Pride Mobility Mobility Aid Jazzy Select 6 User Manual

JAZZY  
S E L E C T S E R I E S  
How a Power Chair should FEEL!  
Jazzy Select  
Jazzy Select 6  
Including Models: Jazzy Select and Jazzy Select 6  
1-800-800-8586 (US) 1-888-570-1113 (Canada)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
C O N T E N T S  
I.  
INTRODUCTION ...................................................................................................................................4  
II. SAFETY....................................................................................................................................................6  
III. YOUR POWER CHAIR ......................................................................................................... 18  
IV. ASSEMBLY............................................................................................................................ 23  
V.  
COMFORT ADJUSTMENTS .............................................................................................. 25  
VI. BATTERIES AND CHARGING ........................................................................................... 31  
VII. CARE AND MAINTENANCE............................................................................................... 35  
VIII. WARRANTY ........................................................................................................................... 42  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
I . I N T R O D U C T I O N  
SAFETY  
WELCOME to Pride Mobility Products Corporation (Pride). The power chair you have purchased combines state-of-  
the-art components with safety, comfort, and styling in mind. We are confident that these design features will provide you  
with the conveniences you expect during your daily activities. Once you understand how to safely operate and care for  
your power chair, it should give you years of trouble free operation and service.  
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the  
first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in  
using good judgement.  
If there is any information in this manual which you do not understand, or if you require additional assistance for setup  
or operation, please contact your authorized Pride Provider. Failure to follow the instructions in this manual and  
those located on your power chair can lead to personal injury and/or damage to the power chair, and may void  
the warranty.  
PURCHASER’S AGREEMENT  
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or  
render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any  
retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.  
SHIPPING AND DELIVERY  
Before using your power chair, make sure your delivery is complete as some components may be individually packaged.  
If you do not receive a complete delivery, please contact your authorized Pride Provider immediately. Where damage has  
occurred during transport, either to the packaging or content, please contact the delivery company responsible.  
INFORMATION EXCHANGE  
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety  
and reliability of your new power chair, and about the service you received from your authorized Pride Provider.  
Please notify us of any change of address, so we can keep you apprised of important information about safety, new  
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to contact us  
at the address below:  
USA:  
Canada:  
Pride Mobility Products Corporation  
Attn.: Customer Care Department  
182 SusquehannaAvenue  
Exeter, PA18643-2694  
800-424-8205  
Pride Mobility Products Company  
380 Vansickle Road Unit 350  
St. Catharines, Ontario L2R 6P7  
1-888-570-1113  
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and  
we will be glad to send you a new one immediately.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I . I N T R O D U C T I O N  
PRIDE OWNERS CLUB  
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and return your  
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You  
will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive  
message boards. These message boards invite you to communicate with other Pride customers as well as Pride represen-  
tatives who are available to assist you with any questions or concerns you may have.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
I I . S A F E T Y  
PRODUCT SAFETY SYMBOLS  
The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very  
important for you to read and understand them completely.  
Read and follow the information in the owner’s manual.  
Do not allow unsupervised children to play near the power chair while the batteries are  
charging.  
Maximum seating weight.  
Keep your hands away from the tires when driving. Be aware that loose fitting clothing  
can become caught in drive tires.  
Use correct tie-down points for controller harness to prevent the harness from getting  
caught in the drive tires or pinched in the seat frame.  
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain  
and store in a clean and dry condition.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I . S A F E T Y  
Do not lift the mobility vehicle while seated in it.  
Do not lift the mobility vehicle while seated in it.  
Do not connect an extension cord to the AC/DC converter or the battery charger.  
Removal of grounding prong can create electrical hazard. If necessary, properly  
install an approved 3-pronged adapter to an electrical outlet having 2-pronged  
plug access.  
Wear safety goggles.  
Corrosive chemicals contained in battery.  
Do not remove the anti-tip wheels.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
I I . S A F E T Y  
EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m.  
Explosive conditions exist!  
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive  
conditions.  
Keep tools and other metal objects away from battery terminals.  
Battery Set Configuration:  
+ = Positive (Red) Terminal Post  
- = Negative (Black) Terminal Post  
Connect Red wire to Red Positive (+) Terminal Post  
Connect Black wire to Black Negative (–) Terminal Post  
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and  
new batteries. Always replace both batteries at the same time.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I . S A F E T Y  
Battery charger for indoor use only.  
Disposal and recycling - Contact your authorized Pride Provider for information on proper  
disposal and recycling of your Pride product and its packaging.  
Disposal and recycling - Contact your authorized Pride Provider for information on proper  
disposal and recycling of your Pride product and its packaging.  
Locked and in drive mode.  
Unlocked and in freewheel mode.  
Do not place power chair in freewheel mode on a decline.  
Do not place power chair in freewheel mode on an incline.  
Contains lead.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
I I . S A F E T Y  
GENERAL GUIDELINES  
MANDATORY! Do not operate your new power chair for the first time without completely reading  
and understanding this owner’s manual.  
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive  
variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and  
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is  
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).  
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair  
to the user and has assisted the prescribing healthcare professional and/or the authorized Pride Provider in the instruction  
process for the use of the product.  
There are certain situations, including some medical conditions, where the power chair user will need to practice operating  
the power chair in the presence of a trained attendant.Atrained attendant can be defined as a family member or care  
professional specially trained in assisting a power chair user in various daily living activities.  
As you begin using your power chair during daily activities, you will probably encounter situations in which you will need  
some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,  
on and off of elevators, up and down ramps, and over moderate terrain.  
Below are some precautions, tips, and other safety considerations that will help you become accustomed to operating your  
power chair safely.  
Modifications  
Pride has designed and engineered your power chair to provide maximum mobility and utility.Awide range of accessories  
is available from your authorized Pride Provider to further customize your power chair to better suit your needs and/or  
preferences. However, under no circumstances should you modify, add, remove, or disable any feature, part, or function  
of your power chair.  
WARNING! Do not modify your power chair in any way not authorized by Pride. Do not use  
accessories if they have not been tested or approved for Pride products.  
Pre-Ride Safety Check  
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before  
each use to make sure your power chair operates smoothly and safely.  
Perform the following inspections prior to using your power chair:  
! Check for proper tire inflation. Maintain but do not exceed35 psi (2.4 bar) in each tire if equipped with pneumatic tires.  
! Check all electrical connections. Make sure they are tight and not corroded.  
! Check all controller connections to the power base. Make sure they are secured properly.  
! Check the brakes. See VII. “Care and Maintenance.”  
! Check battery charge. See VI. “Batteries and Charging.”  
NOTE: If you discover a problem, contact your authorized Pride Provider for assistance.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I . S A F E T Y  
Weight Limitations  
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.  
MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the weight  
capacity voids your warranty. Pride will not be held responsible for injuries and/or property damage  
resulting from failure to observe weight limitations.  
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power  
chair may affect the center of gravity, resulting in a tip or a fall.  
Tire Inflation  
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly. Proper  
inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.  
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at all  
times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and  
overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic tires at  
all times may result in tire and/or wheel failure.  
WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure  
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting in a  
burst tire.  
Incline Information  
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps  
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.  
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.  
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s rear  
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.  
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure a  
safely controlled descent.  
! Avoid sudden stops and starts.  
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate  
cautiously. When driving down an incline, set your power chair to the slowest speed setting and drive in the forward  
direction only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come  
to a complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.  
WARNING! When on any sort of an incline or decline, never place the power chair in  
freewheel mode while seated on it or standing next to it.  
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of  
the incline. Drive your power chair straight up the incline. This greatly reduces the  
possibility of a tip or a fall. Always exercise extreme caution when negotiating an  
incline.  
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas  
covered with snow, ice, cut grass, or wet leaves).  
WARNING! Never travel down an incline backward. Doing so may cause the power  
chair to tip. Always exercise extreme caution when negotiating an incline.  
WARNING! If your power chair is equipped with a reclining seatback, do not attempt  
to negotiate inclines with the seat in a reclined position. Do not attempt to negotiate  
obstacles with the seat in a reclined position unless an attendant is present to help  
stabilize the chair. Failure to heed could result in the power chair tipping over.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
I I . S A F E T Y  
WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated  
in figure 1, do not, under any circumstances, exceed the incline guidelines or any other  
specifications presented in this manual. Doing so could cause instability in your power chair.  
In compliance with theAmericans with DisabilitiesAct of 1990, all handicap public access ramps are required to have a  
maximum slope of 6° (10.5%). Therefore, Pride recommends that the maximum slope of an incline you attempt to safely  
ascend or descend on your power chair does not exceed 6° (10.5%). See figure 1.  
WARNING! Any attempt to climb or descend a slope steeper than 6° (10.5%) may put your power  
chair in an unstable position and cause it to tip.  
6 (10.5%)  
Figure 1. Maximum Safe Slope (Ascending and Descending)  
Freewheel Mode  
Your power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trained attendant.  
For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.”  
WARNING! Do not use your power chair in freewheel mode without an attendant present.  
WARNING! Do not attempt to personally place your power chair in freewheel mode  
while seated on it. Ask an attendant for assistance if necessary.  
WARNING! Do not place your power chair in freewheel mode while on an incline or  
decline. This could cause the chair to roll uncontrollably on its own.  
Braking Information  
Your power chair is equipped with two powerful brake systems:  
! Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.  
! Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when power is  
removed from the system for any reason.  
Cornering Information  
While your power chair is equipped with front and rear caster wheels, excessively high cornering speeds can still create the  
possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to: cornering speed, steering  
angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from an area of low traction to an  
area of high traction (such as passing from a grassy area to a paved area – especially at high speed while turning), and  
abrupt directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a corner,  
reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your power chair from tipping.  
WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.  
This greatly reduces the possibility of a tip or fall.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I . S A F E T Y  
Public Streets and Roadways  
WARNING! You should not operate your power chair on public streets and roadways. Be aware  
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all  
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with  
extreme caution.  
Outdoor Driving Surfaces  
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed  
of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encounter other surface  
types. For this reason, your power chair is designed to perform admirably on packed soil, grass, and gravel. Feel free to  
use your power chair safely on lawns and in park areas.  
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.  
! Avoid tall grass that can entangle the running gear.  
! Avoid loosely packed gravel and sand.  
! If you feel unsure about a driving surface, avoid that surface.  
Inclement Weather Precautions  
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly caught  
up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest opportunity.  
Thoroughly dry your power chair before storing, charging, or operating your power chair.  
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces  
can have an adverse affect on the electrical system. Maintain and store your power chair in a dry  
and clean condition.  
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of upholstered  
and non-upholstered items on the power chair, possibly resulting in skin irritation. Exercise caution  
when using the power chair in extremely hot or cold conditions or when exposing your power  
chair to direct sunlight for prolonged periods of time.  
Stationary Obstacles (Steps, Curbs, etc.)  
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches,  
stairs, etc.). Be sure your power chair is traveling perpendicular to any curb you may be required to navigate. See figure 2.  
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher  
than 2.0 in. (5.08 cm) unless you have the assistance of an attendant.  
WARNING! Do not attempt to have your power chair proceed backward down any step, curb, or  
other obstacle. This may cause the power chair to tip.  
Figure 2. Correct Curb Approach  
Figure 3. Incorrect Curb Approach  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
I I . S A F E T Y  
Stairs and Escalators  
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.  
WARNING! Never use your power chair to negotiate steps or escalators.  
Doors  
! Determine if the door opens toward or away from you.  
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly  
backward to pull the door open.  
Elevators  
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).  
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow the  
rubber door edge to contact the power chair and the door will reopen.  
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.  
Lift/Elevation Products  
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in transporta-  
tion. Pride recommends that you closely review the instructions, specifications, and safety information set forth by the  
manufacturer of the lift/elevation product before using that product.  
WARNING! Never sit on your power chair when it is being used in connection with any  
type of lift/elevation product. Your power chair was not designed with such use in mind  
and any damage or injury incurred from such use is not the responsibility of Pride.  
Motor Vehicle Transport  
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair  
should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and properly secured.  
WARNING! Do not sit on your power chair while it is in a moving vehicle.  
WARNING! Always be sure your power chair and its batteries are properly secured when it is being  
transported. Batteries should be secured in an upright position and protective caps should be  
installed on the battery terminals. Batteries should not be transported with any flammable or  
combustible items.  
Positioning Belts  
Your authorized Pride Provider, therapist(s), and other healthcare professionals are responsible for determining your re-  
quirement for a positioning belt in order to operate your power chair safely.  
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is  
fastened securely in order to reduce the possibility of a fall from the power chair.  
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is  
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be  
properly belted into seats approved by the vehicle manufacturer.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I . S A F E T Y  
Batteries  
In addition to following the warnings below, be sure to comply with all other battery handling information. For more  
information about your power chair’s batteries, see VI. “Batteries and Charging.”  
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead  
compounds. Wear goggles and gloves when handling batteries and wash hands after  
handling.  
WARNING! Power chair batteries are heavy. See specifications table. If you are unable  
to lift that much weight, be sure to get help. Use proper lifting techniques and avoid  
lifting beyond your capacity.  
WARNING! Always protect the batteries from freezing and never charge a frozen battery.  
Charging a frozen battery may result in damage to the battery.  
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables must  
be connected to positive (+) battery terminals/posts. BLACK (-) cables must be  
connected to negative (-) battery terminals/posts. Protective caps should be installed  
over all battery terminals. REPLACE cables immediately if damaged.  
Removable Parts  
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including the  
armrests, seat, foot riggings, controller, and shrouds.  
Preventing Unintended Movement  
WARNING! If you anticipate being seated in a stationary position for an extended period of time,  
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This  
will also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources.  
Reaching and Bending  
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while seated  
on your power chair, it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride  
recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the  
presence of a qualified healthcare professional.  
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the  
floor by reaching down between your knees or if you have to reach over the back of  
the seat. Movements such as these may change your center of gravity and the weight  
distribution of the power chair. This may cause your power chair to tip.  
WARNING! Keep your hands away from the tires when driving. Be aware that loose  
fitting clothing can become caught in drive tires.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
I I . S A F E T Y  
Transfers  
Transferring onto and off of your power chair requires a  
good sense of balance.Always have an attendant or health-  
care professional present while learning to properly transfer  
yourself.  
To eliminate the possibility of injury, Pride recommends that  
you or a trained attendant perform the following tasks be-  
fore attempting a transfer:  
! Turn off the power to the controller.  
! Ensure your power chair is not in freewheel mode. See  
III. “Your Power Chair.”  
! Turn the caster wheels toward the transfer destination  
to improve power chair stability during transfer.  
! Make sure both armrests are flipped up or removed  
from your power chair.  
! Flip up the foot platform or move the leg rests aside;  
this will help to keep your feet from getting caught on  
the foot rigging during the transfer.  
! Reduce the distance between your power chair and the  
object you are transferring onto.  
Figure 4. IdealTransfer Position  
WARNING! Before transferring, position yourself as far back as possible in the power chair seat  
to prevent the power chair from tipping forward during transfer.  
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the armrests  
for weight bearing purposes, such as transfers. Such use may cause the power chair to tip, resulting  
in a fall from the power chair.  
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power  
chair to tip.  
Prescription Drugs/Physical Limitations  
Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when  
taking prescribed or over-the-counter drugs or when the user has specific physical limitations.  
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or  
if you have certain physical limitations. Some medications and limitations may impair your ability  
to operate your power chair in a safe manner.  
Alcohol/Smoking  
The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness  
of safety issues while under the influence of alcohol or while smoking.  
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this  
may impair your ability to operate your power chair in a safe manner.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I . S A F E T Y  
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your  
power chair, although the power chair has passed the necessary testing requirements for cigarette  
smoking. You must adhere to the following safety guidelines if you decide to smoke cigarettes  
while seated in your power chair.  
!
!
!
Do not leave lit cigarettes unattended.  
Keep ashtrays a safe distance from the seat cushions.  
Always make sure cigarettes are completely extinguished before disposal.  
Electromagnetic and Radio Frequency Interference (EMI/RFI)  
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can  
have an adverse affect on the performance of electrically-powered mobility vehicles.  
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way  
radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,  
microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency vehicles. In some  
cases, these waves can cause unintended movement or damage to the control system. Every electrically-powered mobility  
vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the greater the protection against EMI. This  
product has been tested and has passed at an immunity level of 20 V/m.  
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio transmitters  
may cause unintended movement of your electrically-powered mobility vehicle due to EMI.  
Exercise caution when using any of these items while operating your mobility vehicle and avoid  
coming into close proximity of radio and TV stations.  
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle  
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way  
not authorized by Pride.  
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other  
electrical devices located nearby, such as alarm systems.  
unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call Pride  
at 800-424-8205 to report the incident.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
I I I . Y O U R P O W E R C H A I R  
THE JAZZY SELECT SERIES POWER CHAIR  
The Jazzy Select Series Power Chair has two main assemblies: the seat assembly and the power base assembly. See figure 5.  
Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/  
brake assemblies, two drive wheels, two batteries, and wiring harnesses. The Select power base will also include two rear  
caster wheels and two front anti-tip wheels, while the Select 6 will include four caster wheels. See figures 5, 6, 7, and 8.  
SEATBACK  
ARMRESTS  
SEAT ASSEMBLY  
SEAT BASE  
CONTROLLER  
BODY SHROUD  
POWERBASE  
ASSEMBLY  
SEAT  
RELEASE  
LEVER  
CASTERWHEEL  
DRIVEWHEEL  
FOOT RIGGING  
(FOOT PLATFORM SHOWN)  
CASTER WHEELS  
Figure 5.The Jazzy Select Series Power Chair (Jazzy Select 6 Shown)  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I I . Y O U R P O W E R C H A I R  
JAZZYSELECTSERIESSPECIFICATIONS  
Suspension:  
Jazzy Select :Active-Trac  
Jazzy Select 6:Active-Trac with Mid-Wheel 6Technology  
10 in. (25.4 cm), pneumatic or solid available  
Jazzy Select: 6 in. (15.24 cm), solid, rear-mounted  
Jazzy Select 6: 6 in. (15.24 cm), solid, front- and rear-mounted  
Jazzy Select only: 5 in. (12.7 cm), solid, front-mounted  
Up to 4.0 mph (6.44 km/h)  
DriveWheels:  
Caster Wheels:  
Anti-tip Wheels  
MaximumSpeed:1  
Range:1  
Up to 15 miles (24.14 km)  
Brakes:  
“IntelligentBrakingelectronicregenerative, discparkbrake  
Jazzy Select: 3.0 in. (7.62 cm)  
GroundClearance:2  
Jazzy Select 6: 2.0 in. (5.08 cm)  
MaximumSafeSlope:  
TurningRadius:2  
6°(10.5%)  
Jazzy Select: 22 in. (55.88 cm)  
Jazzy Select 6: 20 in. (50.8 cm)  
Jazzy Select Length: 40.5 in. (102.87 cm) with foot platform  
Jazzy Select 6 Length: 35.625 in. (90.49 cm) without foot platform  
Width: 23.5 in. (59.69 cm)  
OverallSize:2  
Drivetrain:  
JazzySelect:Twomotor, Mid-wheeldrive  
JazzySelect6:Twomotor, Mid-wheel-6drive  
Two12-volt, U-1batteries  
Batteries:3  
BatteryCharger:  
Weight Capacity:  
ComponentWeights:  
5-amp,off-board  
300 lbs. (136.08 kg)  
Jazzy Select Base: 90 lbs. (40.82 kg)  
Jazzy Select 6 Base: 100 lbs. (45.36 kg)  
Standard Seat: 37 lbs. (16.78 kg)  
Batteries: 24.5 lbs. (11.11 kg) each  
¹
²
³
Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery condition,  
motors, controller type, tire type, and tire condition.  
Due to manufacturing tolerances and continued product improvement, this specification can be subject to variance of  
(+ or – ) 3%.  
AGM or Gel-Cell type required. See VI. “Batteries and Charging.”  
NOTE: All specifications subject to change without notice.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
I I I . Y O U R P O W E R C H A I R  
CHARGING HARNESS  
REARSHROUD  
SEAT POST  
FRONT COVER  
MAINCIRCUITBREAKER  
CONTROLLER HARNESS  
Figure 6.The Jazzy Select Power Base  
CHARGING HARNESS  
MAIN CIRCUIT BREAKER  
REARSHROUD  
CONTROLLER HARNESS  
Figure 7.The Jazzy Select 6 Power Base  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I I I . Y O U R P O W E R C H A I R  
Electrical Components  
The electrical components are located either on or inside the power base. The main circuit breaker is located on the front  
of the power base. The power module is located under the front cover. See figures 6 and 7.  
Main Circuit Breaker:The main circuit breaker is a safety feature built into your power chair. When the batteries and the  
motors are heavily strained (e.g., from excessive loads), the main circuit breaker trips to prevent damage to the motors and  
the electronics. If the circuit trips, allow your power chair to “rest” for approximately one minute. Next, push in the circuit  
breaker button, turn on the controller, and continue normal operation. If the main circuit breaker continues to trip repeat-  
edly, contact your authorized Pride Provider.  
Power Module: Provides connection between the joystick module and the motors, batteries, and off-board charger port.  
XLR OFF-BOARD CHARGER  
HARNESS CONNECTOR  
JOYSTICK MODULE CONNECTOR  
BATTERY  
CONNECTORS  
MOTOR CONNECTOR  
MAIN CIRCUIT BREAKER  
BATTERY  
CONNECTORS  
Figure 8. Jazzy Select Series Electrical Components (Jazzy Select 6 Shown)  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
I I I . Y O U R P O W E R C H A I R  
Manual Freewheel Levers  
Your power chair has a manual freewheel lever on each motor. Manual freewheel levers enable you to disengage the drive  
motors from the gearboxes and maneuver the chair manually.  
WARNING! Do not use the power chair while the drive motors are disengaged! Do not  
disengage the drive motors when the power chair is on an incline or decline, as the  
unit could roll on its own. Only engage the freewheel mode when on a level surface.  
WARNING! It is important to remember that when your power chair is in freewheel  
mode, the braking system is disengaged.  
To engage or disengage the drive motors:  
1. Locate the lever on each side of the power base. See figure 5.  
2. Pull both levers upward to engage the drive motors (drive mode). See figure 9.  
3. Push both levers downward to disengage the drive motors (freewheel mode). See figure 10.  
If a lever is difficult to move in either direction, slightly rock the power chair back and forth. The lever should then move to  
the desired position.  
WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.  
FREEWHEELLEVER  
FREEWHEELLEVER  
Figure 9. Drive Mode (Drive Engaged)  
Figure 10. Freewheel Mode (Drive Disengaged)  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
I V . A S S E M B L Y  
INITIAL ASSEMBLY  
Your power chair may require some assembly either before initial use or after transportation.  
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be  
replaced with a new nylon insert lock nut. Nylon insert lock nuts should not be reused as it may cause damage  
to the nylon insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local  
hardware stores or through your authorized Pride Provider.  
Seat Installation  
It may be necessary to install the seat either prior to initial  
operation or after transporting your power chair.  
WARNING! Do not pick up the seat  
frame by the armrests. They are free  
to pivot, and you may lose control of  
the seat if they do so.  
To install the seat:  
1. Slidetheseatdownontothepowerbase. Seefigure 11.  
WIRE TIES  
NOTE: The bottom hole on the seat post is  
SEAT  
equipped with an internal welded pin, which sets  
the seat height in the lowest position. If a seat  
JOYSTICK  
MODULE  
SETSCREW  
height other than the lowest position is desired,  
you must install the supplied clevis pin into either  
the middle hole or top hole on the seat post before  
installing the seat.  
QUICKRELEASE  
FASTENER  
CLEVIS PIN  
2. Tighten and clamp the quick-release fastener. See  
figure 12.  
3. Install the joystick module into one of the armrests.  
Tighten the setscrew with the supplied hex key. See  
figure 11.  
4. Lift the armrest straight up, then route the joystick  
module cable and secure with wire-ties as shown in  
figure 11.  
POWERBASE  
NOTE: It is important that the armrest be lifted  
straight up prior to securing the joystick module  
cable with wire-ties.  
Figure 11. Seat and Controller Assembly  
MANDATORY! Prevent controller  
harness damage! Use correct tie-  
down points for controller harness.  
5. Plug the joystick module cable into the connector on  
the power base. See figure 6 or 7.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
I V . A S S E M B L Y  
Quick Release Fasteners: The seat is secured to the seat  
CLAMPED  
UNCLAMPED  
BOLT  
post with a quick release fastener. The quick release fas-  
tener consists of a bolt, a lever, and a nut. See figure 12.  
The lever has a cam on the end that allows it to clamp into  
place. The quick release fastener has two states: clamped  
and unclamped. When the lever is open, the quick release  
fastener is unclamped. When the lever is closed, the quick  
release fastener is clamped.  
LEVER(FULLYCLOSED)  
NUT  
LEVER(OPEN)  
CAM  
To clamp the quick release fastener:  
1. Make sure the lever is in the open position.  
2. Turn the nut clockwise until it is snug.  
3. Rotate the lever until it is in the fully closed position.  
Figure 12. Quick Release Fastener Operation  
NOTE: If the lever will not rotate to the fully closed  
position, then turn the nut counterclockwise one-  
quarter or one-half turn.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V . C O M F O R T A D J U S T M E N T S  
COMFORT ADJUSTMENTS  
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase  
your comfort, such as seat height, armrest angle, foot platform height and angle, and joystick module position. Refer to the  
following information before making comfort adjustments.  
NOTE: If your power chair is equipped with an optional seating system, please refer to the information pro-  
vided in separate manuals.  
WARNING! If your power chair was configured by your authorized Pride Provider, please consult  
your healthcare professional before changing the seat position or making any other adjustment.  
Some adjustments may degrade your power chair’s performance and safety by changing its center  
of gravity.  
WARNING! Some power chair components are heavy. You may need assistance to lift or carry  
them. Please refer to the specifications table for specific component weights before you  
disassemble the power chair.  
WARNING! Remove the occupant from the power chair before making any adjustments.  
Seat Height Adjustment  
You can change the seat height to one of three positions in  
SEAT  
1-in. (2.5 cm) increments.  
To change the seat height:  
1. Turn off the power to the controller.  
2. Make sure that the power chair is in drive mode. See  
figure 9.  
3. Loosen the quick-release fastener. See figure 13.  
4. Remove the seat. See figure 13.  
5. To set the seat to the lowest position, remove the  
SEAT  
RELEASE  
LEVER  
clevis pin (if equipped) from the seat post and reinstall  
the seat post and then the seat.  
QUICK  
RELEASE  
NOTE: The bottom hole on the seat post is equipped  
with an internal welded pin, which sets the seat height  
in the lowest position. The clevis pin is not necessary  
SEAT POST  
FASTENER  
CLEVIS PIN  
for this adjustment.  
6. To set the seat to one of two higher positions, install the  
clevispinintoeitherthemiddleholeforthemiddleheight  
or the top hole for the highest height, then reinstall the  
seat post, and then the seat.  
7. Tighten and clamp the quick-release fastener. See  
figure 12.  
POWERBASE  
NOTE: To rotate the seat use the seat release lever  
located under the seat.  
Figure 13. Seat Height Adjustment  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
V . C O M F O R T A D J U S T M E N T S  
Manual Recline Seatback Adjustment  
If your power chair is equipped with a manual recline  
seatback, you can adjust the seatback angle with the  
seatback release lever. The lever is located on the right side  
of the seat base. See figure 5.  
JAMNUT  
ARMREST  
ANGLE  
ADJUSTMENT  
SCREW  
To adjust the recline angle:  
1. Pull up on the seatback release lever.  
2. Lean forward or backwards to the desired position.  
3. Release the lever.  
ARMREST KNOB  
Seatback Angle Adjustment  
ARMREST  
HEIGHT  
ADJUSTMENT  
SETSCREWS  
If your power chair is equipped with a limited-recline  
seatback, you can adjust it to four (4) different angles: 90°,  
102°, 105°, or 107°.  
To adjust the seatback angle:  
1. Remove the adjusting screws from each seat hinge. See  
figure 14.  
SEATBACK  
ANGLE  
ADJUSTMENT  
SCREW  
2. Set the seatback at the desired angle.  
3. Reinstall the adjusting screws to each seat hinge and  
tighten.  
Figure 14. Seatback/Armrest Adjustment  
Armrest WidthAdjustment  
You can change each armrest’s width independently of  
the other.  
NOTE: Changing the armrest width may increase the  
overall width of your power chair.  
To change the armrest width:  
1. Locate the two armrest knobs on each side of the  
armrest receiver bracket. See figure 14.  
2. Loosen the knobs.  
3. Slide the armrests in or out to the desired width.  
4. Tighten the knobs.  
Armrest Angle Adjustment  
To change the armrest angle:  
1. Lift the armrest straight up so that it is perpendicular to  
the floor. See figure 14.  
2. Loosen the jam nut.  
3. Turn the adjusting screw to raise the front of the  
armrest or to lower the front of the armrest.  
4. Tighten the jam nut to lock the adjusting screw into  
place.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V . C O M F O R T A D J U S T M E N T S  
Armrest HeightAdjustment  
To change the armrest height:  
1. Loosen the setscrews on the armrest. See figure 14.  
2. Raise or lower the armrest to the desired height.  
3. Tighten the setscrews to secure the armrest.  
SETSCREW  
Controller Position  
You can move the controller in toward or out away from the  
armrest, orchangethepositionof thecontrollerforeitherleft-  
handorright-handuse.  
WARNING! Do not place the controller  
cable so that it can be pinched in the  
seat frame or the power base frame.  
To extend the controller:  
1. Flip up the armrest so it is perpendicular to the floor.  
2. Loosen the setscrew on the controller bracket. See  
figure 15.  
Figure 15. Underside of Armrest  
3. Slide the controller into or out of the armrest to the de-  
sired position.  
To change the controller position:  
1. Turn off the power to the controller.  
2. Unplug the joystick module from the connector on the  
power base.  
3. Cut the wire tie(s) that secure the joystick module cable  
to the armrest and seat.  
4. Flipupthearmrest  
5. Loosen the setscrew. See figure 15.  
6. Slide the joystick module out of the armrest.  
7. Loosen the setscrew in the other armrest.  
8. Place the joystick module into the other armrest.  
9. Tighten the setscrew to secure the joystick module.  
10. Route the joystick module cable along the seat frame  
and secure with wire ties. See figure 11.  
11. Plug the controller connector into the power base. See  
figure 6 or 7.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
V . C O M F O R T A D J U S T M E N T S  
Foot Platform Height Adjustment  
Thefootplatformheightiseasilyadjustedtodifferentheights  
in 0.5-in. (1.27-cm) increments.  
To raise or lower the foot platform:  
1. Remove the fasteners from the foot platform bracket.  
See figure 16 or 17.  
2. Raise or lower the foot platform to the desired height.  
3. Reinstall the fasteners into the foot platform bracket and  
tighten.  
FOOT  
PLATFORM  
BRACKET  
Foot Platform Depth Adjustment  
To adjust the foot platform depth:  
1. Remove the fasteners from the foot platform bracket.  
See figure 16 or 17.  
ADJUSTMENT  
2. Move the foot platform in or out to the desired depth.  
3. Reinstall the fasteners into the foot platform bracket and  
tighten.  
SCREW  
Figure 16. Jazzy Select Foot Platform Adjustment  
Foot Platform Angle Adjustment  
You can adjust the angle of the foot platform. See figure 16  
or 17.  
To adjust the foot platform angle:  
1. Flip up the foot platform and locate the adjustment  
screw.  
2. Turn the adjustment screw to raise or lower the front of  
the foot platform.  
FOOT  
PLATFORM  
BRACKET  
ADJUSTMENT  
SCREW  
Figure 17. Jazzy Select 6 Foot Platform Adjustment  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V . C O M F O R T A D J U S T M E N T S  
Swing-away Footrests  
Swing-away Footrests (SFRs) enable you to rotate the foot-  
rests to the side before you transfer onto or off or your power  
chair. See figure 18.  
SFR RELEASE LEVER  
FOOTREST  
EXTENSION  
To rotate the SFRs:  
1. Push in the release lever.  
2. Rotate the SFRs.  
ADJUSTMENT  
SCREWS  
To adjust the SFR length:  
1. Remove the two adjustment screws from the side of  
each footrest extension.  
2. Slide the footrest up or down to the desired length.  
3. Reinstall the two adjustment screws.  
Figure 18. Swing-Away Footrests  
Elevating Leg Rests  
Elevating Leg Rests (ELRs) offer an infinite range of adjust-  
ment for the leg angle and a footrest adjustment range of  
12-19 in. (30.48-48.26 cm). See figure 19.  
RELEASE LEVERA  
RELEASE LEVERB  
To rotate the ELRs:  
1. Push in release leverA.  
2. Rotate the ELRs.  
LEG REST  
EXTENSION  
ADJUSTMENT  
SCREWS  
To adjust the ELR angle:  
1. Push down release lever B.  
2. Move the leg rest to the desired angle.  
To adjust the ELR length:  
1. Remove the two adjustment screws from the side of  
each leg rest extension.  
Figure 19. Elevating Leg Rests  
2. Slide the leg rest up or down to the desired length.  
3. Reinstall the two adjustment screws.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
V . C O M F O R T A D J U S T M E N T S  
Anti-Tip Wheels (Jazzy Select Only)  
The anti-tip wheels are designed to give your power chair increased stability on rough surfaces. The anti-tip wheels are  
preset at the factory for smooth surfaces or indoor use only. If you plan on using your power chair on rough surfaces, it may  
be necessary to adjust the anti-tip wheels to better suit your needs. The anti-tip wheels may need adjustment if the  
followingoccurs:  
! When coming to a stop, your power chair tips forward excessively.  
! The anti-tip wheels constantly rub the ground.  
WARNING! Consult your authorized Pride Provider before attempting to change the anti-tip wheel  
height! Changing the anti-tip wheel height affects handling under acceleration!  
WARNING! The higher you raise the anti-tip wheels, the more you increase your power chair’s  
tendency to tilt forward while decelerating. You can compensate for this by having your authorized  
Pride Provider make a small adjustment to the pre-programmed deceleration setting in the controller  
or by moving the seat assembly farther to the back of your power chair.  
PROHIBITED! Do not remove the anti-tip wheels.  
NOTE: Each drive tire must be inflated to 35 psi (2.4 bar) if equipped with pneumatic tires. The user must also  
be seated in the power chair in order to properly adjust the anti-tip wheels.  
To adjust the anti-tip wheels:  
1. Loosen nut A. See figure 20.  
2. Remove bolt B.  
3. Raise or lower the anti-tip wheel. Each hole is in 0.5 in.  
(1.27 cm) increments.  
4. Reinstall bolt B.  
5. Tighten nutA.  
6. Raise or lower the other anti-tip wheel so that it is at the  
same height.  
A
B
Figure 20. Anti-TipWheel Adjustment  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I . B A T T E R I E S A N D C H A R G I N G  
BATTERIES AND CHARGING  
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.  
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a  
longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.  
Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.  
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead  
compounds. Wear goggles and gloves when handling batteries and wash hands after  
handling.  
PROHIBITED! Always use two batteries of the exact same type, chemistry, and amp-  
hour (Ah) capacity. Refer to the specifications table in this manual and in the manual  
supplied with the battery charger for recommended type and capacities.  
WARNING! Contact your authorized Pride Provider if you have any questions regarding  
the batteries in your power chair.  
Charging the Batteries  
The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power  
chair’s performance by charging the batteries safely, quickly, and easily. The battery charger is only functional when the  
charger power cord is plugged into an electrical outlet.  
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly  
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.  
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger directly  
into a properly wired standard electrical outlet.  
MANDATORY! Read the battery charging instructions in this manual and in the manual supplied  
with the battery charger before charging the batteries.  
PROHIBITED! Do not allow unsupervised children to play near the power chair while the batteries  
are charging. Pride recommends that you do not charge the batteries while the power chair is  
occupied.  
WARNING! Explosive gases may be generated while charging the batteries. Keep the power chair  
and battery charger away from sources of ignition such as flames or sparks and provide adequate  
ventilation when charging the batteries.  
WARNING! You must recharge your power chair’s batteries with the supplied off-board/onboard  
battery charger. Do not use an automotive-type battery charger.  
WARNING! Inspect the battery charger, wiring, and connectors for damage before each use. Contact  
your authorized Pride Provider if damage is found.  
WARNING! Do not attempt to open the battery charger case. If the battery charger does not  
appear to be working correctly, contact your authorized Pride Provider.  
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to insert  
objects through these slots.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
V I . B A T T E R I E S A N D C H A R G I N G  
WARNING! If your battery charger has not been tested and approved for outdoor use,  
then do not expose it to adverse or extreme weather conditions. If the battery charger  
is exposed to adverse or extreme weather conditions, then it must be allowed to adjust  
to the difference in environmental conditions before use indoors. Refer to the manual  
supplied with the battery charger for more information.  
To charge the batteries using the off-board charger:  
1. Position the front of your power chair next to a standard electrical outlet.  
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power  
Chair.”  
3. Plug the off-board charger into the off-board charger/programming socket on the controller.  
4. Plug the off-board charger into the electrical outlet.  
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to  
the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride off-  
board charger, then follow the instructions supplied by the manufacturer.  
5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.  
Battery Break-in  
To break in new batteries for maximum efficiency:  
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance  
level.  
2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you  
become accustomed to the controls and break in the batteries.  
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now  
perform at over 90% of their potential.  
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.  
Frequently Asked Questions (FAQs)  
How does the charger work?  
The battery charger takes the standard electrical outlet voltage of 120VAC (alternating current) and converts it to 24 VDC  
(direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is low, the  
charger works harder to charge the battery.As the battery voltage approaches full charge, the charger doesn’t work as  
hard to complete the charging cycle. When the battery is fully charged, the amperage from the charger is nearly at zero.  
This is how the charger maintains a charge but does not overcharge the battery.  
Can I use a different battery charger?  
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do  
not recommend using other types of chargers (e.g., an automotive battery charger).  
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero  
voltage. If this happens, call your authorized Pride Provider for assistance.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I . B A T T E R I E S A N D C H A R G I N G  
How often must I charge the batteries?  
Many factors come into play when deciding how often to charge the batteries.You may use your power chair all day on a  
daily basis or you may not use it for weeks at a time.  
! Daily Use  
If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair.  
Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the  
batteries 8 to 14 hours after daily use.  
! InfrequentUse  
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per week  
for 12 to 14 hours.  
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the  
batteries for more than 24 hours at a charging cycle.  
How can I get maximum range or distance per charge?  
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More often you  
are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind.All of these factors will  
affect the distance or running time per battery charge. Below are a few suggestions for obtaining the maximum range per  
charge:  
! Always charge the batteries fully prior to your trip.  
! Plan your trip in advance to avoid inclines if possible.  
! Limit baggage weight to essential items.  
! Try to maintain an even speed and avoid stop-and-go driving.  
What type of batteries should I use?  
We recommend deep-cycle batteries that are sealed and maintenance free. BothAGM and Gel-Cell are deep-cycle  
batteries that are similar in performance.  
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell  
batteries to reduce the risk of leakage or explosive conditions.  
Why do my new batteries seem weak?  
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads),  
or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain down their  
charge, and then accept a relatively quick recharge.AGM and Gel-Cell batteries should be charged as often as possible.  
They do not have a “memory” like nickel-cadmium batteries.  
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific demands.  
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encoun-  
ter temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the  
power available and extends the time needed to recharge the battery (just as with a car battery).  
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More  
importantly, it will take a few “charging cycles” (a partial drain— then a full recharge) to establish the critical chemical  
balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in  
your battery properly.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
33  
V I . B A T T E R I E S A N D C H A R G I N G  
How can I ensure maximum battery life?  
Afully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s  
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or  
stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery life.  
NOTE: The useful life of a battery is quite often a reflection of the care it receives.  
How should I store my power chair and its batteries?  
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least  
once per week.  
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect  
the battery harnesses and store the power chair in a warm, dry environment.Avoid temperature extremes, such as freezing  
and excessively hot conditions, and never attempt to charge a frozen battery.Acold or frozen battery should be warmed  
for several days prior to recharging.  
What about public transportation?  
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are  
FederalAviationAdministration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no  
danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s  
specific requirements.  
What about shipping?  
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the  
original shipping container and ship the batteries in separate boxes.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I I . C A R E A N D M A I N T E N A N C E  
CARE AND MAINTENANCE  
Your Jazzy Select 6 is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance checks.You  
can perform some of these checks, but others require assistance from your authorized Pride Provider. Preventive mainte-  
nance is very important. If you follow the maintenance checks in this section as scheduled, you can help ensure that your  
power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care or operation,  
contact your authorized Pride Provider.  
WARNING! Do not service the power chair when the seat is occupied.  
Your power chair, like most electrical equipment, is susceptible to damage from the elements.Avoid damp areas of any kind.  
WARNING! Direct or prolonged exposure to water or dampness could cause the power  
chair to malfunction electronically and mechanically. Water can cause electrical  
components to corrode and the chair’s frame to rust. Power chairs should be examined  
periodically for signs of corrosion cause by water exposure, bodily fluids exposure, or  
incontinence. Damaged components should be replaced or treated immediately.  
Should your power chair come in contact with water:  
1. Dry your power chair as thoroughly as possible with a towel.  
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.  
3. Check the joystick operation and the brakes before using your power chair again.  
4. If any inconsistencies are found, take your power chair to your authorized Pride Provider. Power chairs that are  
frequently exposed to sources of water, such as incontinence, should be inspected often for corrosion and electronic  
components may need to be replaced frequently.  
Temperature  
! Some of the parts of your power chair are susceptible to extreme changes in temperature.Always keep your power  
chair between the temperatures of 18°F (-8°C) and 122°F (50°C).  
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a  
number of factors, such as battery charge, usage, and composition of the batteries (e.g.,AGM or Gel-Cell).  
! Temperatures above 122°F (50°C) may cause your power chair to operate at a reduced speed. This reduced speed  
is a safety feature built into the controller that helps prevent damage to the motor and other electrical components.  
General Guidelines  
! Avoid knocking or bumping the controller, especially the joystick.  
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.  
! Keep the controller clean.  
! Check all connectors to ensure that they are all tight and secured properly.  
! Make sure pneumatic tires are inflated to 35 psi (2.4 bar).  
WARNING! Make sure your tires are inflated to 35 psi (2.4 bar). Do not underinflate or overinflate  
your tires. Low pressure may result in loss of control, and overinflated tires may burst. Overinflating  
tires can cause them to explode.  
WARNING! Do not use a high pressure hose to inflate your tires.  
! Use a rubber conditioner on the tire sidewalls to help preserve them.  
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the  
tires slippery and cause your power chair to skid.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
35  
V I I . C A R E A N D M A I N T E N A N C E  
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.  
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain  
its high-gloss appearance.  
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery  
boxes and battery well frame with the battery terminals facing inward toward each other. Refer to the battery wiring  
label for the correct wiring layout.  
WARNING! Even though the power chair has passed the necessary testing requirements  
for ingress of liquids, you should keep electrical connections away from sources of  
dampness, including direct exposure to water or bodily fluids and incontinence. Check  
electrical components frequently for signs of corrosion and replace as necessary.  
Daily Checks  
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral  
position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the  
boot. Do not handle or try to repair it. See your authorized Pride Provider if there is a problem.  
! Visually inspect the controller communications cable. Make sure that it is not frayed, cut, or has any wires exposed.  
See your authorized Pride Provider if there is a problem.  
! Check for flat spots on solid tires. Flat spots could adversely affect stability.  
Weekly Checks  
! Disconnect and inspect the controller cable and the charger harness from the power base. Look for corrosion. Contact  
your authorized Pride Provider if necessary.  
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.  
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see your  
authorized Pride Provider for replacement of the tube.  
! Checkthebrakes. Thistestshouldbecarriedoutonalevelsurfacewithatleast3feetofclearancearoundyourpowerchair.  
To check the brakes:  
1. Turn on the controller and turn down the speed level of your power chair.  
2. After one second, check the battery condition meter. Make sure that it remains on.  
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick.You must be  
able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this test three times,  
pushing the joystick backward, then left, and then right.  
Monthly Checks  
! Check that the anti-tip wheels do not rub the ground when you operate the power chair.Adjust them as necessary.  
! Check for extreme wear on the anti-tip wheels. Replace them as necessary.  
! Check for drive tire wear. See your authorized Pride Provider for repair.  
! Check the caster wheels for wear. Replace them as necessary.  
! Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings  
replaced. See your authorized Pride Provider for repair.  
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.  
Yearly Checks  
Take your power chair to your authorized Pride Provider for yearly maintenance, especially if you use your power chair on  
a daily basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I I . C A R E A N D M A I N T E N A N C E  
Storage  
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries  
from the power chair. See VI. “Batteries and Charging.”  
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be  
damaged.  
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored without  
a full charge may be permanently damaged, causing unreliable performance and limited service life. It is recommended that  
you charge the batteries periodically throughout periods of prolonged storage to ensure proper performance.  
You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of  
prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the  
tires contacting the ground.  
Disposal of Your Power Chair  
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact your local  
waste disposal agency or authorized Pride Provider for information on proper disposal of power chair packaging, metal  
frame components, plastic components, electronics, and batteries.  
Cleaning and Disinfection  
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair.Avoid using  
products that may scratch the surface of your power chair.  
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your  
product before application.  
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning  
agent before applying it to your product. Failure to comply may result in skin irritation or premature  
deterioration of upholstery and/or power chair finishes.  
WARNING! Never hose off your power chair or place it in direct contact with water. Your power  
chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a  
damp cloth.  
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become  
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.  
Wheel Replacement  
If you have pneumatic tires and you have a flat tire, replace the tube. If your chair is equipped with a solid tire insert, then  
you must replace the whole wheel assembly. Replacement tires, tubes, and wheel assemblies are readily available through  
your authorized Pride Provider.  
WARNING! The wheels on your power chair should only be serviced or replaced by an authorized  
Pride Provider or a qualified technician.  
WARNING! Be sure that the power to the controller is turned off and the power chair is not in  
freewheel mode before performing this procedure.  
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the  
wheel. If any further disassembly is required, deflate the tire completely or it may explode.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
37  
V I I . C A R E A N D M A I N T E N A N C E  
DRIVE  
WHEEL  
MOTOR  
KEY  
TUBE  
ACORN NUTS  
RIM HALF  
DRIVE WHEEL NUT  
HUBCAP  
WHEEL  
HUB  
RIM  
HALF  
AXLE  
TIRE  
WARNING! Completely deflate  
the tire before attempting repair.  
DRIVEWHEELWASHER  
Figure 21. Jazzy Select 6 DriveWheel  
Figure 22.Tire Removal  
Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:  
1. Turn off the power to the controller.  
2. Make sure that the power chair is in drive mode. See figure 8.  
3. Raise and support the power base so that the wheel is at least 1 in. (2.5 cm) off of the ground.  
4. Completely deflate the tire (if the tire is pneumatic).  
5. Remove the hub cap. See figure 21.  
6. Remove the drive wheel nut and washer from the axle. See figure 21.  
7. Remove the drive wheel from the axle. Make sure that you keep the key.  
8. Remove the acorn nuts that fasten the two rim halves together. See figure 22.  
9. Remove the old tube from the pneumatic tire and replace it with a new tube or replace the entire assembly if it is a solid tire.  
10. Reassemble the two rim halves.  
11. Slide the wheel back onto the axle. Make sure that the key is in the axle slot.  
12. Reinstall the drive wheel nut and washer onto the axle and tighten. See figure 22.  
13. Reinstall the hub cap.  
14. Inflate the pneumatic tire to 35 psi (2.4 bar).  
15. Remove the power chair from the base support.  
Battery Replacement  
A battery wiring diagram is printed on a decal located the power base. See VI. “Batteries and Charging” for correct  
battery specifications.  
MANDATORY! Battery posts, terminals, and related accessories contain lead and lead  
compounds. Wear goggles and gloves when handling batteries and wash hands after  
handling.  
WARNING! The batteries in your power chair should only be serviced or replaced by an  
authorized Pride Provider or a qualified technician.  
WARNING! Do not replace batteries when seat is occupied.  
WARNING! Power chair batteries are heavy. See specifications table. If you are unable  
to lift that much weight, be sure to get help.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I I . C A R E A N D M A I N T E N A N C E  
CORRECT  
CONNECTION  
INCORRECT  
CONNECTION  
REAR  
SHROUD  
CONTROLLER  
COVER SHROUD  
YELLOW  
THUMBSCREWS  
REAR BATTERY  
FRONT  
BATTERY  
SIDE COVER  
Figure 23. Battery Installation (Seat Removed for Clarity)  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
39  
V I I . C A R E A N D M A I N T E N A N C E  
WARNING! Use proper lifting techniques and avoid lifting beyond your capacity. Do not mix or  
match new and old batteries. If you encounter a situation where one battery needs to be replaced,  
then replace both batteries. Refer to specifications table in this manual and the manual supplied  
with the battery charger for recommended type and capacities.  
To replace the batteries:  
1. Turn off power to the controller.  
2. Make sure that the power chair is in drive mode. See figure 8.  
3. Remove the rear shroud. See figure 23.  
4. Loosen the yellow thumbscrews and remove the side cover.  
5. Disconnect the rear battery harness from the power base. See figure 23.  
6. Slide the rear battery out of the power base.  
7. Slide the front battery rearward.  
8. Disconnect the front battery harness from the power base. See figure 23.  
9. Slide the front battery out of the power base.  
10. Remove the battery harnesses from the old batteries and install them onto the new batteries. Make sure that the  
hardware is facing the correct direction. See figure 23.  
WARNING! Make sure you tighten the fasteners so that the connections are secure.  
11. Place the front battery into the power base. Make sure that the terminals are facing the front of the power base. See  
figure 23.  
12. Connect the front battery harness to the power base.  
13. Slide the front battery forward.  
14. Place the rear battery onto the power base. Make sure that the terminals are facing the front of the power base. See  
figure 23.  
15. Connect the rear battery harness to the power base.  
16. Reinstall the side cover.  
17. Reinstall the rear shroud.  
18. Charge the batteries. See VI. “Batteries and Charging.”  
When to See Your Authorized Pride Provider for Service  
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your authorized  
Pride Provider. When calling, have the model number, serial number, nature of the problem, and the error code if available.  
! Motor noise  
! Frayed harnesses  
! Cracked or broken connectors  
! Uneven wear on any of the tires  
! Jerky motion  
! Pulling to one side  
! Bent or broken wheel assemblies  
! Does not power up  
! Powers up, but does not move  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I I . C A R E A N D M A I N T E N A N C E  
Corrective Maintenance  
If the battery condition meter does not light up when you turn on the power:  
! Check the harness connections. Make sure they are tight.  
! Check the circuit breaker. Reset it if necessary.  
! Check the battery connections.  
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available  
at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load  
tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up,  
contact your authorized Pride Provider.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
41  
V I I I . W A R R A N T Y  
LIFETIME LIMITED WARRANTY  
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the original  
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Pride to be  
defective in material and/or workmanship:  
Structural frame components, including:  
! Main Frame  
! Fixed-position seat post  
TWO-YEAR LIMITED WARRANTY  
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of  
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in  
material and/or workmanship:  
Electronic components, including:  
! ChargerAssembly  
! Controller  
Main frame assemblies, including:  
! Caster forks  
! Caster beam ! Metal seat framing  
! Joystick  
Other components, including:  
! Foot riggings  
! Electrical Harness ! Foot rigging mounting brackets  
18-MONTH LIMITED WARRANTY  
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free  
of charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in  
material and/or workmanship:  
! Motor/gearbox assembly ! Power seat actuator  
ONE-YEAR LIMITED WARRANTY  
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of  
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in  
material and/or workmanship:  
! Accessories  
! Brakes (electronic function ONLY)  
SIX-MONTH LIMITED WARRANTY  
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of  
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in  
material and/or workmanship:  
! Bearings and bushings  
! Plastic components, except body  
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are not  
warranted by Pride.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Jazzy Select Series  
V I I I . W A R R A N T Y  
RECONDITIONED UNITS WARRANTY  
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.  
WARRANTY EXCLUSIONS  
This warranty does not extend to those items which may require replacement due to normal wear and tear.  
! ABS Plastic shrouds  
! Motor brushes  
! Upholstery and seating  
! Brake Pads  
! Tires and tubes  
! Fuses/Bulbs  
! Circumstances beyond the control of Pride  
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically authorized, IN  
ADVANCE, by Pride Mobility Products Corporation  
! Repairs and/or modifications made to any part without specific consent from Pride  
Exclusions also include components with damage caused by:  
! Contamination  
! Abuse, misuse, accident, or negligence  
! Battery fluid spillage or leakage  
! Commercial use, or use other than normal  
! Improper operation, maintenance, or storage  
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in  
cold conditions for an extended period of time, or worn out through heavy use is not covered.  
SERVICE CHECKS AND WARRANTY SERVICE  
Warranty service must be performed by an authorized Pride Provider. Do not return faulty parts to Pride without prior  
written authorization.All transportation costs and shipping damage incurred while submitting parts for repair or replacement  
are the responsibility of the purchaser.  
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride product can  
result in personal injury or product damage and will void Pride’s product warranty.  
There is no other express warranty.  
IMPLIED WARRANTIES  
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from  
the date of purchase and to the extent permitted by law.Any and all implied warranties are excluded. This is the exclusive  
remedy. Liabilities for consequential damages under any and all warranties are excluded.  
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation  
incidental or consequential damages. The above limitation or exclusion may not apply to you.  
This warranty gives you specific rights, and you may also have other rights which vary from state to state.  
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible technical  
and customer service.  
Jazzy Select Series  
Download from Www.Somanuals.com. All Manuals Search And Download.  
43  
Quality Control - Jazzy Select Series  
Inclusion of all Parts  
Joystick Serial Number  
Controller Serial Number  
Left Motor Serial Number  
Right Motor Serial Number  
Fit and Finish  
Performance  
Jazzy Select  
Jazzy Select 6  
Date Inspected  
Inspector  
*I NFMANU3351  
Product Serial #  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Computer Monitor 105S05 User Manual
Philips DVD Player DVD 620 User Manual
Philips Garage Door Opener 32PF9631D 10 User Manual
Philips Iron GC3260 User Manual
Phoenix Gold Speaker SX110D2 User Manual
Planar Computer Monitor PL2010MW User Manual
Planar Computer Monitor PT1814NUV User Manual
Planet Technology Switch WGS3 2840 User Manual
Plantronics Headphones BackBeat 903+ User Manual
Polaroid Digital Camera ProCamCamera User Manual