QUANTUM
6 0 0 0 Z S E R I E S
INNOVATIVE REHAB SOLUTIONS
Including Models: Quantum 6000Z 3S, Quantum 6000Z 3SP, Quantum 6000Z 3MP,
Quantum 6000Z 4S, Quantum 6000Z 4SP, and Quantum 6000Z 4MP
1-800-800-8586 (US) 1-888-570-1113 (Canada)
Download from Www.Somanuals.com. All Manuals Search And Download.
C O N T E N T S
I.
INTRODUCTION.................................................................................................................................4
II. SAFETY .................................................................................................................................................6
III. YOUR POWER CHAIR....................................................................................................................18
IV. ASSEMBLY.........................................................................................................................................24
V. COMFORT ADJUSTMENTS........................................................................................................27
VI. BATTERIES AND CHARGING ....................................................................................................33
VII. CARE AND MAINTENANCE ........................................................................................................36
VIII.WARRANTY........................................................................................................................................42
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
3
I . I N T R O D U C T I O N
SAFETY
WELCOME to Quantum Rehab, a division of Pride Mobility Products Corporation (Pride). The power chair you have
purchased combines state-of-the-art components with safety, comfort, and styling in mind. We are confident that these
design features will provide you with the conveniences you expect during your daily activities. Once you understand how
to safely operate and care for your power chair, it should give you years of trouble free operation and service.
Read and follow all instructions, warnings, and notes in this manual before attempting to operate your power chair for the
first time. In addition, your safety depends upon you, as well as your provider, caretaker, or healthcare professional in
using good judgement.
If there is any information in this manual which you do not understand, or if you require additional assistance for setup
or operation, please contact your Quantum Rehab Specialist. Failure to follow the instructions in this manual and
those located on your power chair can lead to personal injury and/or damage to the power chair, including
voiding the warranty.
PURCHASER’S AGREEMENT
By accepting delivery of this product, you promise that you will not change, alter, or modify this product or remove or
render inoperable or unsafe any guards, shields, or other safety features of this product; fail, refuse, or neglect to install any
retrofit kits from time to time provided by Pride to enhance or preserve the safe use of this product.
SHIPPING AND DELIVERY
Before using your power chair, make sure your delivery is complete as some components may be individually packaged.
If you do not receive a complete delivery, please contact your Quantum Rehab Specialist immediately. Where damage has
occurred during transport, either to the packaging or content, please contact the delivery company responsible.
INFORMATION EXCHANGE
We want to hear your questions, comments, and suggestions about this manual. We would also like to hear about the safety
and reliability of your new power chair, and about the service you received from your Quantum Rehab Specialist.
Please notify us of any change of address, so we can keep you apprised of important information about safety, new
products, and new options that can increase your ability to use and enjoy your power chair. Please feel free to contact us
at the address below:
USA:
Canada:
Pride Mobility Products Corporation
Attn.: Customer Care Department
182 SusquehannaAvenue
Exeter, PA18643-2694
800-424-8205
Pride Mobility Products Company
380 Vansickle Road Unit 350
St. Catharines, Ontario L2R 6P7
1-888-570-1113
NOTE: If you ever lose or misplace your product registration card or your copy of this manual, contact us and
we will be glad to send you a new one immediately.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I . I N T R O D U C T I O N
PRIDE OWNERS CLUB
As an owner of a Pride product, you are encouraged to enroll in the Pride Owners Club. Complete and return your
From our home page, select “Owners Club” to enter a page dedicated to current and potential Pride product owners. You
will gain access to interviews, stories, recreation ideas, daily living tips, product and funding information, and interactive
message boards. These message boards invite you to communicate with other Pride customers as well as Pride represen-
tatives who are available to assist you with any questions or concerns you may have.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
5
I I . S A F E T Y
PRODUCT SAFETY SYMBOLS
The symbols below are used on the power chair to identify warnings, mandatory actions, and prohibited actions. It is very
important for you to read and understand them completely.
Read and follow the information in the owner’s manual.
Do not allow unsupervised children to play near the power chair while the batteries are
charging.
Maximum seating weight.
Keep your hands away from the tires when driving. Be aware that loose fitting clothing
can become caught in drive tires.
Use correct tie-down points for controller harness to prevent the harness from getting
caught in the drive tires or pinched in the seat frame.
Avoid exposure to rain, snow, ice, salt, or standing water whenever possible. Maintain
and store in a clean and dry condition.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I . S A F E T Y
Do not lift the mobility vehicle while seated in it.
Do not lift the mobility vehicle while seated in it.
Do not connect an extension cord to the AC/DC converter or the battery charger.
Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged
plug access.
Wear safety goggles.
Corrosive chemicals contained in battery.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
7
I I . S A F E T Y
EMI-RFI - This product has been tested and passed at an immunity level of 20 V/m.
Explosive conditions exist!
Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive
conditions.
Keep tools and other metal objects away from battery terminals.
Battery Set Configuration:
+ = Positive (Red) Terminal Post
- = Negative (Black) Terminal Post
Connect Red wire to Red Positive (+) Terminal Post
Connect Black wire to Black Negative (–) Terminal Post
Do not use batteries with different amp-hour (Ah) capacities. Do not mix old and
new batteries. Always replace both batteries at the same time.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I . S A F E T Y
Battery charger for indoor use only.
Disposal and recycling - Contact your Quantum Rehab Specialist for information on proper
disposal and recycling of your Pride product and its packaging.
Disposal and recycling - Contact your Quantum Rehab Specialist for information on proper
disposal and recycling of your Pride product and its packaging.
Locked and in drive mode.
Unlocked and in freewheel mode.
Do not place power chair in freewheel mode on a decline.
Do not place power chair in freewheel mode on an incline.
Contains lead.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
9
I I . S A F E T Y
GENERAL GUIDELINES
MANDATORY! Do not operate your new power chair for the first time without completely reading
and understanding this owner’s manual.
Your power chair is a state-of-the-art life-enhancement device designed to increase mobility. Pride provides an extensive
variety of products to best fit the individual needs of the power chair user. Please be aware that the final selection and
purchasing decision regarding the type of power chair to be used is the responsibility of the power chair user, who is
capable of making such a decision, and his/her healthcare professional (i.e., medical doctor, physical therapist, etc.).
The contents of this manual are based on the expectation that a mobility device expert has properly fitted the power chair
to the user and has assisted the prescribing healthcare professional and/or the Quantum Rehab Specialist in the instruction
process for the use of the product.
There are certain situations, including some medical conditions, where the power chair user will need to practice operating
the power chair in the presence of a trained attendant.Atrained attendant can be defined as a family member or care
professional specially trained in assisting a power chair user in various daily living activities.
As you begin using your power chair during daily activities, you will probably encounter situations in which you will need
some practice. Simply take your time and you will soon be in full and confident control as you maneuver through doorways,
on and off of elevators, up and down ramps, and over moderate terrain.
Below are some precautions, tips, and other safety considerations that will help you become accustomed to operating your
power chair safely.
Modifications
Pride has designed and engineered your power chair to provide maximum mobility and utility.Awide range of accessories
is available from your Quantum Rehab Specialist to further customize your power chair to better suit your needs and/or
preferences. However, under no circumstances should you modify, add, remove, or disable any feature, part, or function
of your power chair.
WARNING! Do not modify your power chair in any way not authorized by Pride. Do not use
accessories if they have not been tested or approved for Pride products.
Pre-Ride Safety Check
Get to know the feel of your power chair and its capabilities. Pride recommends that you perform a safety check before
each use to make sure your power chair operates smoothly and safely.
Perform the following inspections prior to using your power chair:
! Check for proper tire inflation. Maintain but do not exceed35 psi (2.4 bar) in each tire if equipped with pneumatic tires.
! Check all electrical connections. Make sure they are tight and not corroded.
! Check all controller connections to the power base. Make sure they are secured properly.
! Check the brakes. See VII. “Care and Maintenance.”
! Check battery charge. See VI. “Batteries and Charging.”
NOTE: If you discover a problem, contact your Quantum Rehab Specialist for assistance.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I . S A F E T Y
Weight Limitations
Your power chair is rated for a maximum weight capacity. Please refer to the specifications table for this limit.
MANDATORY! Stay within the specified weight capacity of your power chair. Exceeding the weight
capacity voids your warranty. Pride will not be held responsible for injuries and/or property damage
resulting from failure to observe weight limitations.
WARNING! Do not carry passengers on your power chair. Carrying passengers on your power
chair may affect the center of gravity, resulting in a tip or a fall.
Tire Inflation
If your power chair is equipped with pneumatic tires, you should check or have the air pressure checked regularly. Proper
inflation pressures will prolong the life of your tires and help ensure the smooth operation of your power chair.
WARNING! It is important that 35 psi (2.4 bar) tire pressure be maintained in pneumatic tires at all
times. Do not underinflate or overinflate your tires. Low pressure may result in loss of control, and
overinflated tires may burst. Failure to maintain 35 psi (2.4 bar) tire pressure in pneumatic tires at
all times may result in tire and/or wheel failure.
WARNING! Inflate your power chair drive tires from a regulated air source with an available pressure
gauge. Inflating your tires from an unregulated air source could overinflate them, resulting in a
burst tire.
Incline Information
More and more buildings have ramps with specified degrees of inclination, designed for easy and safe access. Some ramps
may have turning switchbacks (180-degree turns) that require you to have good cornering skills on your power chair.
! Proceed with extreme caution as you approach the downgrade of a ramp or other incline.
! Take wide swings with your power chair’s front wheels around any tight corners. If you do that, the power chair’s rear
wheels will follow a wide arc, not cut the corner short, and not bump into or get hung up on any railing corners.
! When driving down a ramp, keep the power chair’s speed adjustment set to the slowest speed setting to ensure a
safely controlled descent.
! Avoid sudden stops and starts.
When climbing an incline, try to keep your power chair moving. If you must stop, start up again slowly and then accelerate
cautiously. When driving down an incline, set your power chair to the slowest speed setting and drive in the forward
direction only. If your power chair starts to move down the incline faster than you anticipated or desired, allow it to come
to a complete stop by releasing the joystick, then push the joystick forward slightly to ensure a safely controlled descent.
WARNING! When on any sort of an incline or decline, never place the power chair in
freewheel mode while seated on it or standing next to it.
WARNING! When climbing an incline, do not zigzag or drive at an angle up the face of the incline.
Drive your power chair straight up the incline. This greatly reduces the possibility of a tip or a fall.
Always exercise extreme caution when negotiating an incline.
WARNING! You should not travel up or down a potentially hazardous incline (i.e., areas covered
with snow, ice, cut grass, or wet leaves).
WARNING! Never travel down an incline backward. Doing so may cause the power chair to tip.
Always exercise extreme caution when negotiating an incline.
WARNING! If your power chair is equipped with a reclining seatback, do not attempt to negotiate
inclines with the seat in a reclined position. Do not attempt to negotiate obstacles with the seat
in a reclined position unless an attendant is present to help stabilize the chair. Failure to heed
could result in the power chair tipping over.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
11
I I . S A F E T Y
WARNING! Even though your power chair is capable of climbing slopes greater than those illustrated
in figure 1, do not, under any circumstances, exceed the incline guidelines or any other
specifications presented in this manual. Doing so could cause instability in your power chair.
In compliance with theAmericans with DisabilitiesAct of 1990, all handicap public access ramps are required to have a
maximum slope of 5° (8.7%). Therefore, Pride recommends that the maximum slope of an incline you attempt to safely
ascend or descend on your power chair does not exceed 5° (8.7%). See figure 1.
WARNING! Any attempt to climb or descend a slope steeper than 5° (8.7%) may put your power
chair in an unstable position and cause it to tip.
5 (8.7%)
Figure 1. Maximum Safe Slope (Ascending and Descending)
Freewheel Mode
Your power chair is equipped with two manual freewheel levers to allow for manual maneuverability by a trained attendant.
For more information about how to place your power chair into and out of freewheel mode, see III. “Your Power Chair.”
WARNING! Do not use your power chair in freewheel mode without an attendant present.
WARNING! Do not attempt to personally place your power chair in freewheel mode while seated
on it. Ask an attendant for assistance if necessary.
WARNING! Do not place your power chair in freewheel mode while on an incline or
decline. This could cause the chair to roll uncontrollably on its own.
Braking Information
Your power chair is equipped with two powerful brake systems:
! Regenerative — uses electricity to rapidly slow the vehicle when the joystick returns to the center/stop position.
! Disc Park Brake — activates mechanically after regenerative braking slows the vehicle to near stop, or when power is
removed from the system for any reason.
Cornering Information
While your power chair is equipped with front and rear caster wheels, excessively high cornering speeds can still create the
possibility of tipping. Factors which affect the possibility of tipping include, but are not limited to: cornering speed, steering
angle (how sharply you are turning), uneven road surfaces, inclined road surfaces, riding from an area of low traction to an
area of high traction (such as passing from a grassy area to a paved area – especially at high speed while turning), and
abrupt directional changes. High cornering speeds are not recommended. If you feel that you may tip over in a corner,
reduce your speed and steering angle (i.e., lessen the sharpness of the turn) to prevent your power chair from tipping.
WARNING! When cornering sharply, reduce your speed and maintain a stable center of gravity.
This greatly reduces the possibility of a tip or fall.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I . S A F E T Y
Public Streets and Roadways
WARNING! You should not operate your power chair on public streets and roadways. Be aware
that it may be difficult for traffic to see you when you are seated on your power chair. Obey all
local pedestrian traffic rules. Wait until your path is clear of traffic, and then proceed with
extreme caution.
Outdoor Driving Surfaces
Your power chair is designed to provide optimum stability under normal driving conditions—dry, level surfaces composed
of concrete, blacktop, or asphalt. However, Pride recognizes that there will be times when you will encounter other surface
types. For this reason, your power chair is designed to perform admirably on packed soil, grass, and gravel. Feel free to
use your power chair safely on lawns and in park areas.
! Reduce your power chair’s speed when driving on uneven terrain and/or soft surfaces.
! Avoid tall grass that can entangle the running gear.
! Avoid loosely packed gravel and sand.
! If you feel unsure about a driving surface, avoid that surface.
Inclement Weather Precautions
Exposure of your power chair to inclement weather conditions should be avoided whenever possible. If suddenly caught
up in rain, snow, severe cold or heat while operating your power chair, proceed to shelter at the earliest opportunity.
Thoroughly dry your power chair before storing, charging, or operating your power chair.
PROHIBITED! Operating in rain, snow, salt, mist/spray conditions, and on icy/slippery surfaces
can have an adverse affect on the electrical system. Maintain and store your power chair in a dry
and clean condition.
WARNING! Prolonged exposure to hot or cold conditions may affect the temperature of upholstered
and non-upholstered items on the power chair, possibly resulting in skin irritation. Exercise caution
when using the power chair in extremely hot or cold conditions or when exposing your power
chair to direct sunlight for prolonged periods of time.
Stationary Obstacles (Steps, Curbs, etc.)
Proceed with extreme caution when driving near raised surfaces, unprotected ledges and/or drop-offs (curbs, porches,
stairs, etc.). Be sure your power chair is traveling perpendicular to any curb you may be required to navigate. See figure 2.
WARNING! Do not attempt to have your power chair climb or descend an obstacle that is higher
than 2 in. (5) cm) unless you have the assistance of an attendant.
WARNING! Do not attempt to have your power chair proceed backward down any step, curb, or
other obstacle. This may cause the power chair to tip.
Figure 2. Correct Curb Approach
Figure 3. Incorrect Curb Approach
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
13
I I . S A F E T Y
Stairs and Escalators
Power chairs are not designed to travel up or down stairs or escalators. Always use an elevator.
WARNING! Never use your power chair to negotiate steps or escalators.
Doors
! Determine if the door opens toward or away from you.
! Drive your power chair gently and slowly forward to push the door open. Or drive your power chair gently and slowly
backward to pull the door open.
Elevators
Modern elevators have a door edge safety mechanism that, when pushed, reopens the elevator door(s).
! If you are in the doorway of an elevator when the door(s) begin to close, push on the rubber door edge or allow the
rubber door edge to contact the power chair and the door will reopen.
! Use care that pocketbooks, packages, or power chair accessories do not become caught in elevator doors.
Lift/Elevation Products
If you will be traveling with your power chair, you may find it necessary to use a lift/elevation product to aid in transporta-
tion. Pride recommends that you closely review the instructions, specifications, and safety information set forth by the
manufacturer of the lift/elevation product before using that product.
WARNING! Never sit on your power chair when it is being used in connection with any
type of lift/elevation product. Your power chair was not designed with such use in mind
and any damage or injury incurred from such use is not the responsibility of Pride.
Motor Vehicle Transport
Pride recommends that you do not remain seated in your power chair while traveling in a motor vehicle. The power chair
should be stowed in the trunk of a car or in the back of a truck or van with batteries removed and properly secured.
WARNING! Do not sit on your power chair while it is in a moving vehicle.
WARNING! Always be sure your power chair and its batteries are properly secured when it is being
transported. Batteries should be secured in an upright position and protective caps should be
installed on the battery terminals. Batteries should not be transported with any flammable or
combustible items.
Positioning Belts
Your Quantum Rehab Specialist, therapist(s), and other healthcare professionals are responsible for determining your
requirement for a positioning belt in order to operate your power chair safely.
WARNING! If you require a positioning belt to safely operate your power chair, make sure it is
fastened securely in order to reduce the possibility of a fall from the power chair.
WARNING! The positioning belt is not designed for use as a seat belt in a motor vehicle. Nor is
your power chair suitable for use as a seat in any vehicle. Anyone traveling in a vehicle should be
properly belted into seats approved by the vehicle manufacturer.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I . S A F E T Y
Batteries
In addition to following the warnings below, be sure to comply with all other battery handling information. For more
information about your power chair’s batteries, see VI. “Batteries and Charging.”
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after
handling.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help. Use proper lifting techniques and avoid lifting beyond your
capacity.
WARNING! Always protect the batteries from freezing and never charge a frozen battery. Charging
a frozen battery may result in damage to the battery.
WARNING! Connect the battery harnesses in the proper manner. RED (+) cables must be connected
to positive (+) battery terminals/posts. BLACK (-) cables must be connected to negative (-) battery
terminals/posts. Protective caps should be installed over all battery terminals. REPLACE cables
immediately if damaged.
Removable Parts
WARNING! Do not attempt to lift or move a power chair by any of its removable parts, including the
armrests, seat, foot riggings, controller, and shrouds.
Preventing Unintended Movement
WARNING! If you anticipate being seated in a stationary position for an extended period of time,
turn off the power. This will prevent unexpected motion from inadvertent joystick contact. This
will also eliminate the possibility of unintended chair movement from electromagnetic (EM) sources.
Reaching and Bending
Never reach, lean, or bend while driving your power chair. If it is absolutely necessary to reach, lean, or bend while seated
on your power chair, it is important to maintain a stable center of gravity and keep the power chair from tipping. Pride
recommends that the power chair user determine his/her personal limitations and practice bending and reaching in the
presence of a qualified healthcare professional.
WARNING! Do not bend, lean, or reach for objects if you have to pick them up from the floor by
reaching down between your knees or if you have to reach over the back of the seat. Movements
such as these may change your center of gravity and the weight distribution of the power chair.
This may cause your power chair to tip.
WARNING! Keep your hands away from the tires when driving. Be aware that loose
fitting clothing can become caught in drive tires.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
15
I I . S A F E T Y
Transfers
Transferring onto and off of your power chair requires a
good sense of balance.Always have an attendant or health-
care professional present while learning to properly trans-
fer yourself.
To eliminate the possibility of injury, Pride recommends that
you or a trained attendant perform the following tasks be-
fore attempting a transfer:
! Turn off the power to the controller.
! Ensure your power chair is not in freewheel mode. See
III. “Your Power Chair.”
! Turn the caster wheels toward the transfer destination
to improve power chair stability during transfer.
! Make sure both armrests are flipped up or removed
from your power chair.
! Flip up the foot platform or move the leg rests aside;
this will help to keep your feet from getting caught on
the foot rigging during the transfer.
! Reduce the distance between your power chair and the
object you are transferring onto.
Figure 4. IdealTransfer Position
WARNING! Before transferring, position yourself as far back as possible in the power chair seat
to prevent the power chair from tipping forward during transfer.
WARNING! Avoid putting all of your weight on the power chair armrests and do not use the armrests
for weight bearing purposes, such as transfers. Such use may cause the power chair to tip, resulting
in a fall from the power chair.
WARNING! Avoid putting all of your weight on the foot riggings. Such use may cause the power
chair to tip.
Prescription Drugs/Physical Limitations
Users must exercise care and common sense when operating a power chair. This includes awareness of safety issues when
taking prescribed or over-the-counter drugs or when the user has specific physical limitations.
WARNING! Consult your physician if you are taking prescribed or over-the-counter medication or
if you have certain physical limitations. Some medications and limitations may impair your ability
to operate your power chair in a safe manner.
Alcohol/Smoking
The power chair user must exercise care and common sense when operating his/her power chair. This includes awareness
of safety issues while under the influence of alcohol or while smoking.
WARNING! Do not operate your power chair while you are under the influence of alcohol, as this
may impair your ability to operate your power chair in a safe manner.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I . S A F E T Y
WARNING! Pride strongly recommends that you do not smoke cigarettes while seated in your
power chair, although the power chair has passed the necessary testing requirements for cigarette
smoking. You must adhere to the following safety guidelines if you decide to smoke cigarettes
while seated in your power chair.
!
!
!
Do not leave lit cigarettes unattended.
Keep ashtrays a safe distance from the seat cushions.
Always make sure cigarettes are completely extinguished before disposal.
Electromagnetic and Radio Frequency Interference (EMI/RFI)
WARNING! Laboratory tests have shown that electromagnetic and radio frequency waves can
have an adverse affect on the performance of electrically-powered mobility vehicles.
Electromagnetic and Radio Frequency Interference can come from sources such as cellular phones, mobile two-way
radios (such as walkie-talkies), radio stations, TV stations, amateur radio (HAM) transmitters, wireless computer links,
microwave signals, paging transmitters, and medium-range mobile transceivers used by emergency vehicles. In some
cases, these waves can cause unintended movement or damage to the control system. Every electrically-powered mobility
vehicle has an immunity (or resistance) to EMI. The higher the immunity level, the greater the protection against EMI. This
product has been tested and has passed at an immunity level of 20 V/m.
WARNING! Be aware that cell phones, two-way radios, laptops, and other types of radio transmitters
may cause unintended movement of your electrically-powered mobility vehicle due to EMI.
Exercise caution when using any of these items while operating your mobility vehicle and avoid
coming into close proximity of radio and TV stations.
WARNING! The addition of accessories or components to the electrically-powered mobility vehicle
can increase the susceptibility of the vehicle to EMI. Do not modify your power chair in any way
not authorized by Pride.
WARNING! The electrically-powered mobility vehicle itself can disturb the performance of other
electrical devices located nearby, such as alarm systems.
unintended motion or brake release occurs, turn your power chair off as soon as it is safe to do so. Call Pride
at 800-424-8205 to report the incident.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
17
I I I . Y O U R P O W E R C H A I R
THE QUANTUM 6000Z SERIES
The Quantum 6000Z Series has two main assemblies: the seat assembly and the power base assembly. See figure 5.
Typically, the seat assembly includes the armrests, seatback, and seat base. The power base assembly includes two motor/
brake assemblies, two drive wheels, four caster wheels, two batteries, and wiring harnesses. See figures 5, 6, and 7.
SEATBACK
SEAT ASSEMBLY
ARMREST
JOYSTICK
CONTROLLER
(Q-LOGICSHOWN)
SEAT BASE
POWERBASE
ASSEMBLY
CASTER WHEEL
MANUALFREEWHEELLEVER
FOOT RIGGING
DRIVE WHEEL
(FOOT PLATFORM SHOWN)
CASTER WHEEL
Figure 5.The Quantum 6000Z Series
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I I . Y O U R P O W E R C H A I R
QUANTUM6000ZSERIESSPECIFICATIONS
Suspension:
Active-TracATXwithintegratedreardual-strutsuspensionandarticulatingcasterbeam
14 in. (35.56cm), pneumatic(14in. (35.56cm)solidoptional)
6 in. (15.24 cm) solid
DriveWheels:
CasterWheels:
MaximumSpeed:¹
Upto6mph(9.66km/h)(standardinGroup3)
Upto8mph(12.87km/h)(standardinGroup4;optionalinGroup3)
“IntelligentBraking”electronicregenerative, discparkbrake
3.5 in. (8.89 cm)
Brakes:
GroundClearance:²
MaximumSafeSlope:
TurningRadius:²
OverallSize:²
5°(8.7%)
22.5in.(57.15cm)(withoutfootriggings)
Length:36in.(91.44cm)(withoutfootriggings)
Width: 25.875 in. (65.75 cm)
Drivetrain:
Batteries:³
Twomotor, Mid-wheel-6drive
Two12-volt, deep-cycle, NF-22/Group24batteries(standard)
Two12-volt,NF-22requiredwithPowerElevatingSeat
Up to 20 miles (32.19 km)
Range:¹
BatteryCharger:
5-amp, off-board(standardinGroup3)
8-amp, off-board(standardinGroup4;optionalinGroup3)
300lbs. (136kg)
WeightCapacity:
250lbs. (113.4kg)withTRU-BalancePediatricPowerTilt
160lbs. (72.57)withSynergyManualTilt
Base: 147 lbs. (66.68 kg)
ComponentWeights:
Batteries:NF-22batteries38lbs. each(17.24kg);Group24batteries53lbs. (24.04kg)
¹
Varies with base model, user weight, terrain type, battery amp hour rating (Ah), battery charge, battery condition, motors, controller
type, tire type, and tire condition.
²
³
Due to manufacturing tolerances and continued product improvement, this specification can be subject to a variance of (+ or – ) 3%.
AGM or Gel-Cell type required. See VI. “Batteries and Charging.”
NOTE: All specifications subject to change without notice.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
19
I I I . Y O U R P O W E R C H A I R
REAR SEAT MOUNT CONNECTORS
FRONT SEAT MOUNT CONNECTORS
REARSHROUD
REARSHROUDFASTENER
(FASTENER ON OPPOSITE
SIDE NOT SHOWN)
FRONT COVER
MANUALFREEWHEELLEVER
Figure 6.The Quantum 6000Z Series Power Base
Electrical Components
The electrical components consist of the controller assembly, the batteries, and the motors. The batteries, motors, and
controller power module (if equipped) are located on the power base assembly. The controller is located on the seat
assembly. Connectivity between the controller and the motors, batteries, and the battery charger is provided by one or
more wiring harnesses. See figure 7.
Controller Cable Connector: This is where the controller connects to the power base. Each controller uses a different
type of cable. Regardless of which type of controller is used, the cable must be secured to the assembly and not allowed
to drag on the floor.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I I I . Y O U R P O W E R C H A I R
Motor Connectors: This is where the controller connects to the motors.
Battery Connector: This is where the controller connects to the batteries.
Controller Power Module: This enables the controller to communicate with the batteries and the motors.
Main Circuit Breaker (located on the rear main frame): The main circuit breaker is a safety feature built into your
power chair. When the batteries and the motors are heavily strained (e.g., from excessive loads), the main circuit breaker
trips to prevent damage to the motors and the electronics. If the circuit trips, allow your power chair to “rest” for approxi-
mately one minute. The circuit breaker will reset itself. Turn on the controller, and continue normal operation. If the main
circuit breaker continues to trip repeatedly, contact your Quantum Rehab Specialist.
CONTROLLER
POWERMODULE
CONTROLLER
CABLE
TO MOTOR
CONNECTORS
QUICKRELEASE
BATTERY CONNECTORS
MAINCIRCUITBREAKER
Figure 7. Quantum 6000Z Series Electrical Components
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
21
I I I . Y O U R P O W E R C H A I R
Dual Manual Freewheel Levers
For your convenience, your power chair is equipped with dual manual freewheel levers. The levers are located on each
motor, and allow you to disengage the drive motors and maneuver the chair manually.
WARNING! Do not use the power chair while the drive motors are disengaged! Do not
disengage the drive motors when the power chair is on an incline, as the unit could roll
on its own! Only engage the freewheel mode when on a level surface.
WARNING! It is important to remember that when your power chair is in freewheel mode, the
braking system is disengaged.
To operate the dual manual freewheel levers:
1. Push down both manual freewheel levers for freewheel mode (drive motor disengaged). See figure 8.
2. Pull up both manual freewheel levers for drive mode (drive motor engaged). See figure 9.
NOTE: You must turn off the power before disengaging the drive motors, otherwise you may get an error code
on the controller. To clear this code, turn off the controller, place the power chair in drive mode, then turn on
the controller. The error message should be cleared. If it is not cleared, contact your Quantum Rehab Special-
ist.
NOTE: The power chair will be significantly easier to push with the power off.
! Avoid applying excessive force to the manual freewheel levers.
WARNING! Do not use your foot to operate the manual freewheel levers. Do not stand on the
manual freewheel levers. Applying excessive force to the manual freewheel levers may result in
damage to the freewheel levers, motors, and brakes.
WARNING! Do not use the freewheel lever handles as tie-down points to secure this product.
MANUAL FREEWHEELLEVER
MANUAL FREEWHEELLEVER
Figure 8. Freewheel Mode (Drive Disengaged)
Figure 9. Drive Mode (Drive Engaged)
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I V . A S S E M B L Y
INITIAL ASSEMBLY
Your power chair may require some assembly either before initial use or after transportation. It may also require disassembly
to make some comfort adjustments. Figure 10 details those parts of the power chair that are designed to be disassembled and
assembled by an end user or by a qualified caregiver before using the product or making comfort adjustments.
NOTE: Any nylon insert lock nut removed during the disassembly or adjustment of the power chair must be
replaced with a new nut. Nylon insert lock nuts should not be reused as it may cause damage to the nylon
insert, resulting in a less secure fit. Replacement nylon insert lock nuts are available at local hardware stores
or through your Quantum Rehab Specialist.
ARMREST ANGLE ADJUSTMENT
CONTROLLER POSITION
SEAT HEIGHT/ANGLE ADJUSTMENT
FOOT PLATFORM
ANGLEADJUSTMENT
FOOT PLATFORM HEIGHT/DEPTH ADJUSTMENT
Figure 10. Quantum 6000Z Series AssemblyView (Synergy Seat Shown)
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
23
I V . A S S E M B L Y
Seat Installation
SEAT
It may be necessary to install the seat either prior to initial
operation or after transporting your power chair. Contour
seats are attached to the power base with the Universal
Mounting System (UMS). The UMS consists of universal
parts that may be attached to the seat, regardless of seat
width or seat depth. The two main components are alumi-
num extrusions mounted to the seat base. These extrusions
attach to a pair of trapeze bars that are mounted to the
power base. See figure 11.
LATCH
SAFETY
NOTE: If your power chair is equipped with a Spe-
cialty Seat, Synergy Seat, or a Synergy TRU-Balance
Power Positioning System, refer to the information
provided in separate manuals.
REAR
EXTRUSION
FRONT
EXTRUSION
TRAPEZE
BARS
WARNING! Do not pick up the seat frame
by the armrests. They are free to pivot,
and you may lose control of the seat if
they do so.
To install the seat:
1. Tilt the seat back and slide the rear extrusion onto the
rear trapeze bar. See figure 11.
2. Lower the front extrusion onto the front trapeze bar
until the seat locks into place.
3. Flip the seat latch safety down.
Figure 11. Universal Mounting System and Contour
Seat
WARNING! Make sure the seat latch
safety is flipped down before using your
power chair.
4. Install the controller and route the cable to the back of
the power base. See figures 12 and 13.
5. Loosen the rear shroud fasteners and remove the rear
shroud. See figure 6.
6. Plug the controller connector into the power base. See
figure 7.
7. Replace the rear shroud and tighten the rear shroud
fasteners. See figure 6.
8. Secure the controller cable to the armrest receiver with
wire ties (contour seats only). See figure 13.
WARNING! Prevent controller harness
damage! Use correct tie-down points for
controller harness.
Figure 12. Controller Routed on a Synergy Seat
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
I V . A S S E M B L Y
Power Seat Option Installation
Your power chair maybeequipped with the power seat op-
tion. Whilethe seatitselfmay beanyoneofthe styles offered
for this model, the way the seat base attaches to the power
baseisdifferent.
To install the power seat:
l. Place the seat plate interface bracket onto the actuator.
Seefigure 14.
2. Insert screws into the actuator and insert and tighten
the hardware.
3. Place seating system onto the seat plate and secure.
Figure 13. Controller Routed on a Contour Seat
SEAT PLATE INTERFACE BRACKET
ACTUATOR
Figure 14. Power Seat Actuator
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
25
V . C O M F O R T A D J U S T M E N T S
COMFORT ADJUSTMENTS
After becoming familiar with your power chair’s operation, you may find the need to make some adjustments to increase
your comfort, such as seat height and angle, armrest width, armrest angle and height, foot platform height, depth, and
angle, and controller position.
NOTE: If your power chair is equipped with a Specialty Seat, Synergy Seat, or Synergy TRU-Balance Power
Positioning System, refer to the information provided in separate manuals.
WARNING! If your power chair was configured by your Quantum Rehab Specialist, please consult
your healthcare professional before making any adjustment that may degrade your power chair’s
performance and safety by changing its center of gravity.
WARNING! Some power chair components are heavy. You may need assistance to lift or carry
them. Please refer to the specifications table for specific component weights before you
disassemble the power chair.
WARNING! Remove the occupant from the power chair before making any adjustments.
You may need the following to make comfort adjustments:
! metric/standard socket set and ratchet
! adjustable wrench
! metric/standard hex key set
! thread lock
TRAPEZE BARS
SEAT
POSTS
Seat Height and Seat Angle Adjustment
You can change the seat height to one of three positions in
1-in. increments by raising the front and rear trapeze bars.
If you raise or lower only one trapeze bar (front or rear),
you can also change the seat base angle (dump).
RETAINING
CLIPS
SEAT POSTS
To change the seat height:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Loosen the rear shroud fasteners and remove the rear
shroud. See figure 6.
4. Disconnect the controller connector(s) from the power
base. See figure 7.
5. Flip up the seat latch safety. See figure 11.
6. Squeeze the seat latch and release the seat from
the front trapeze bar.
RETAINING
CLIPS
7. Slide the seat forward and remove it from the power
base.
8. Remove the retaining clips that attach the trapeze bars
to the seat posts. See figure 15.
Figure 15. Seat Height/Angle Adjustment
9. Move the trapeze bars up or down to the desired height.
NOTE: Change the seat dump by raising or lowering
only one set of towers (front or rear).
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V . C O M F O R T A D J U S T M E N T S
10. Reinstall the retaining clips.
11. Reinstall the seat.
12. Reconnect the controller to the power base.
13. Reinstall the rear shroud and tighten the fasteners.
Seat Position
You can move the seat forward or rearward by changing
the extrusion mounting position.
To change the position:
1. Turn off the power to the controller.
2. Make sure the power chair is in drive mode.
3. Loosen the rear shroud fasteners and remove the rear
shroud.
4. Unplug the controller connector(s) from the power base.
5. Remove the seat from the power base.
6. Remove both extrusions from the bottom of the seat.
7. Reposition the extrusions on a different set of mounting
holes.You must move both extrusions the same number
of holes either forward or backwards. See figure 16.
8. Fasten the extrusions back onto the bottom of the seat.
9. Reinstall the seat.
SEAT MOUNTING
HOLES
Figure 16. Seat Position Adjustment
10. Reconnect the controller to the power base.
11. Reinstall the rear shroud and tighten the fasteners.
JAMNUT
ARMRESTANGLE
ADJUSTINGSCREW
Manual Recline Seatback Adjustment
If your power chair is equipped with a reclining seat, you
can adjust the seatback angle with the seatback release le-
ver. The lever is located on the right side of the seat base.
ARMREST HEIGHT
ADJUSTING
SETSCREWS
To adjust the recline angle:
1. Pull up on the seatback release lever.
2. Lean forward or backwards to the desired position.
3. Release the lever.
SEATBACKANGLE
ADJUSTINGSCREW
Seatback Angle Adjustment
If your power chair is equipped with an adjustable seatback,
you can adjust it to four (4) different angles: 90°, 102°,
105°, or 107°.
ARMREST KNOB
Figure 17. Seatback/Armrest Adjustment
To adjust the seatback angle:
1. Remove the adjusting screws from each seat hinge. See
figure 17.
2. Set the seatback at the desired angle.
3. Reinstalltheadjustingscrewstoeachseathingeandtighten.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
27
V . C O M F O R T A D J U S T M E N T S
Armrest Width Adjustment
Youcanchangeeacharmrest’swidthindependentlyoftheother.
NOTE: Changing the armrest width may increase the
overall width of your power chair.
To change the armrest width:
SETSCREW
1. Locate the two armrest knobs on each side of the arm
rest receiver bracket. See figure 17.
2. Loosen the knobs.
3. Slide the armrests in or out to the desired width.
4. Tighten the knobs.
Armrest HeightAdjustment
To change the armrest height:
1. Loosen the two setscrews located on the armrest receiver.
2. Raise or lower the armrest to the desired height.
3. Tighten the setscrews to secure the armrest.
Armrest Angle Adjustment
To change the armrest angle:
1. Lift the armrest straight up so that it is perpendicular to
the floor. See figure 17.
Figure 18. Underside of Armrest (Contour Seat)
2. Loosen the jam nut.
3. Turn the adjusting screw to raise the front of the armrest
or to lower the front of the armrest.
MOUNTING BLOCK
MOUNTING SCREWS
4. Tighten the jam nut to lock the adjusting screw into place.
Controller Position
You can position the controller for either left-hand or right-
hand use.
WARNING! Do not place the controller
cable so that it can be pinched in the
seat frame or the power base frame.
SETSCREWS
To extend the controller:
Figure 19. Adjusting Controller Position (Mounting
Block)
1. Flip up the armrest so it is perpendicular to the floor.
2. Loosen the setscrew on the controller bracket. See
figure 18.
3. Slide the controller into or out of the armrest to the de-
sired position.
NOTE: If your power chair is equipped with a Spe-
cialty Seat, Synergy Seat, or TRU-Balance Power Po-
sitioning System, loosen the setscrews in the mount-
ing block, slide the controller in or out to the desired
position, then tighten the setscrews. See figure 19.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V . C O M F O R T A D J U S T M E N T S
To change the controller position:
1. Turn off the power to the controller.
2. Loosen the rear shroud fasteners and remove the rear
shroud.
3. Unplug the controller connector from the power base.
4. Remove any wire ties securing the controller cable to
the armrest.
FOOT
PLATFORM
BRACKET
QUICK
RELEASE
FASTENERS
5. Loosen the mounting screws in the controller mounting
block. See figure 19.
6. Move the controller mounting block and controller to
the other armrest and tighten the mounting screws.
NOTE: For contour seats, loosen the setscrew on the
underside of both armrests, transfer the controller, and
tighten the setscrews. See figure 18.
Figure 20. Foot Platform Adjustment
7. Route the controller cable to the back of the power
base and plug in the controller. See figures12 and 13.
8. Replace the rear shroud and tighten the fasteners.
9. Secure the controller cable to the armrest with wire ties.
See figure 13.
LEVER(FULLY
CLOSED)
CAM
NUT
Foot Platform Height Adjustment
The foot platform height is easily adjusted to different heights
in 1/2-in. (1.27-cm) increments.
BOLT
CLAMPED
To raise or lower the foot platform:
1. Remove the quick release fasteners from the foot plat-
form bracket. See figure 20.
UNCLAMPED
LEVER(OPEN)
2. Raise or lower the foot platform to the desired height.
3. Reinstall the quick release fasteners into the foot plat-
form bracket and tighten.
Figure 21. Quick Release Fastener Operation
Foot Platform Depth Adjustment
To adjust the foot platform depth:
1. Remove the quick release fasteners from the foot plat-
form bracket. See figure 20.
2. Move the foot platform in or out to the desired depth.
3. Reinstall the quick release fasteners into the foot plat-
form bracket and tighten.
Quick Release Fasteners: The foot platform is attached
to the power base with two quick release fasteners. See
figure 20. Each quick release fastener consists of a bolt, a
lever, and a nut. See figure 21. The lever has a cam on the
end that allows it to clamp into place. The quick release fas-
tener has two states: clamped and unclamped. When the
lever is open, the quick release fastener is unclamped. When
the lever is closed, the quick release fastener is clamped
NUT
SET SCREW
Figure 22. Underside of Foot Platform
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
29
.
V . C O M F O R T A D J U S T M E N T S
To clamp the quick release fastener:
1. Make sure the lever is in the open position.
2. Turn the nut clockwise until it is snug.
3. Rotate the lever until it is in the fully closed position.
SFR RELEASE LEVER
NOTE: If the lever will not rotate to the fully closed
position, then turn the nut counterclockwise one-
quarter or one-half turn.
FOOTREST
EXTENSION
ADJUSTMENT
SCREWS
Foot Platform Angle Adjustment
You can adjust the angle of the foot platform with a hex key.
To adjust the foot platform angle:
1. Flip up the foot platform and locate the setscrew. See
figure 22.
Figure 23. Swing-Away Footrests
2. Loosen the nut securing the setscrew.
3. Turn the setscrew to raise or lower the front of the foot
platform.
RELEASE LEVERA
RELEASE LEVERB
4. Tighten the nut to secure the setscrew.
Swing-away Footrests
Swing-away Footrests (SFRs) enable you to rotate the foot-
rests to the side before you transfer onto or off or your power
chair. See figure 23.
LEG REST
EXTENSION
ADJUSTMENT
SCREWS
To rotate the SFRs:
1. Push in the release lever.
2. Rotate the SFRs.
To adjust the SFR length:
Figure 24. Elevating Leg Rests
1. Remove the two adjustment screws from the back of
each footrest extension.
2. Slide the footrest up or down to the desired length.
3. Reinstall the two adjustment screws.
LEG REST
HANGER
Elevating Leg Rests (Optional)
ADJUSTMENT BOLT
Elevating Leg Rests (ELRs) offer an infinite range of ad-
justment for the leg angle and a footrest adjustment range
of 12–19 in. (30.48-48.26 cm). See figure 24.
LEG REST ADJUSTMENT
SCREWS
To rotate the ELRs:
1. Push in release leverA.
2. Rotate the ELRs.
To adjust the ELR angle:
1. Push down release lever B.
2. Move the leg rest to the desired angle.
Figure 25. Heavy Duty Drop-In Leg Rests
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V . C O M F O R T A D J U S T M E N T S
To adjust the ELR length:
1. Remove the two adjustment screws from the side of
each leg rest extension.
2. Slide the leg rest up or down to the desired length.
3. Reinstall the two adjustment screws.
Heavy Duty Drop-in Leg Rests
You can adjust the forward/back position, as well as the
length of the heavy duty drop-in leg rests. See figure 25.
A
B
To adjust the forward/back position:
1. Remove the adjustment bolt from each side rail.
2. Move the leg rest hanger in or out to the desired position.
3. Align the adjustment holes in the leg rest hanger with
those in the side rail.
C
D
4. Reinstall the adjustment bolts to secure the leg rest
hangers.
To adjust the leg rest length:
1. Remove the adjustment screws from the leg rest
extension.
A
2. Slide the leg rest up or down to the desired length.
3. Align the adjustment holes in the leg rest extension and
reinstall the adjustment screws.
Multi-Axis Foot Plates
The multi-axis foot plate assembly can be installed on either
a swing-away footrest or an elevating leg rest. The multi-
axis foot plate has four adjustments: leg rest length (A), po-
sition (B), tilt (C), and angle (D). See figure 26.
B
To change leg rest length (A):
1. Remove the hardware.
2. Move the leg rest to the desired position.
C
3. Reinstall the hardware.
To change foot plate position (B):
1. Remove the hardware.
2. Move the foot plate to the desired position.
3. Reinstall the hardware.
D
To change foot plate tilt (C):
1. Loosen the hardware.
2. Tilt the foot plate to the desired position.
3. Tighten the hardware.
SETSCREW
To change foot plate angle (D):
1. Turn the setscrew clockwise to decrease the angle.
2. Turnthe setscrew counterclockwiseto increasetheangle.
Figure 26. Multi-Axis Foot Plate (ELR Shown)
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
31
V I . B A T T E R I E S A N D C H A R G I N G
BATTERIES AND CHARGING
Your power chair uses two long-lasting, 12-volt, deep-cycle batteries. These batteries are sealed and maintenance free.
Since they are sealed, there is no need to check the electrolyte (fluid) level. Deep-cycle batteries are designed to handle a
longer and deeper discharge. Though they are similar in appearance to automotive batteries, they are not interchangeable.
Automotive batteries are not designed to handle a long, deep discharge, and also are unsafe for use in power chairs.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after
handling.
WARNING! Always use two batteries of the exact same type, chemistry, and amp-hour
(Ah) capacity. Refer to the specifications table in this manual and in the manual supplied
with the battery charger for recommended type and capacities.
WARNING! Contact your Quantum Rehab Specialist if you have any questions regarding the
batteries in your power chair.
Charging the Batteries
The battery charger is essential in providing long life for your power chair batteries. It is designed to optimize your power
chair’s performance by charging the batteries safely, quickly, and easily.
PROHIBITED! Removal of grounding prong can create electrical hazard. If necessary, properly
install an approved 3-pronged adapter to an electrical outlet having 2-pronged plug access.
PROHIBITED! Never use an extension cord to plug in your battery charger. Plug the charger
directly into a properly wired standard electrical outlet.
MANDATORY! Read the battery charging instructions in this manual and in the manual supplied
with the battery charger before charging the batteries.
WARNING! Explosive gases may be generated while charging the batteries. Keep the power chair
and battery charger away from sources of ignition such as flames or sparks and provide adequate
ventilation when charging the batteries.
WARNING! You must recharge your power chair’s batteries with the supplied off-board battery
charger. Do not use an automotive-type battery charger.
WARNING! Inspect the battery charger, wiring, and connectors for damage before each use.
Contact your Quantum Rehab Specialist if damage is found.
WARNING! Do not attempt to open the battery charger case. If the battery charger does not
appear to be working correctly, contact your Quantum Rehab Specialist.
WARNING! If the battery charger is equipped with cooling slots, then do not attempt to insert
objects through these slots.
PROHIBITED! Do not allow unsupervised children to play near the power chair while the batteries
are charging. Pride recommends that you do not charge the batteries while the power chair is
occupied.
WARNING! If your battery charger has not been tested and approved for outdoor use,
then do not expose it to adverse or extreme weather conditions. If the battery charger
is exposed to adverse or extreme weather conditions, then it must be allowed to
adjust to the difference in environmental conditions before use indoors. Refer to the
manual supplied with the battery charger for more information.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V I . B A T T E R I E S A N D C H A R G I N G
To charge the batteries using the off-board charger:
1. Position the front of your power chair next to a standard electrical outlet.
2. Be certain the controller power is turned off and the freewheel levers are in the engaged position. See III. “Your Power
Chair.”
3. Plug the off-board charger into the off-board charger/programming socket on the controller.
4. Plug the off-board charger into the electrical outlet.
NOTE: If it is a Pride off-board charger, then there are two lights in it. The red light indicates that power to
the off-board charger is on. The green light indicates that the batteries are fully charged. If it is not a Pride off-
board charger, then follow the instructions supplied by the manufacturer.
5. When the batteries are fully charged, unplug the off-board charger from the electrical outlet and then from the controller.
Battery Break-in
To break in new batteries for maximum efficiency:
1. Fully recharge any new battery prior to its initial use. This brings the battery up to about 90% of its peak performance
level.
2. Operate your power chair throughout the house and yard. Move slowly at first, and do not travel too far until you
become accustomed to the controls and break in the batteries.
3. Give the batteries another full charge of 8 to 14 hours and operate your power chair again. The batteries will now
perform at over 90% of their potential.
4. After four or five charging cycles, the batteries will top off at 100% charge and last for an extended period.
Frequently Asked Questions (FAQs)
How does the charger work?
The battery charger takes the standard electrical outlet voltage of 120VAC (alternating current) and converts it to 24VDC
(direct current). The power chair batteries use direct current to run your power chair. When the battery voltage is low, the
charger works harder to charge the battery.As the battery voltage approaches full charge, the charger doesn’t work as
hard to complete the charging cycle. When the battery is fully charged, the amperage from the charger is nearly at zero.
This is how the charger maintains a charge but does not overcharge the battery.
Can I use a different battery charger?
You should use the charger supplied with the power chair. It is the safest, most efficient tool to charge the batteries. We do
not recommend using other types of chargers (e.g., an automotive battery charger).
NOTE: Your power chair’s charger will not operate after the batteries have been discharged to nearly zero
voltage. If this happens, call your Quantum Rehab Specialist for assistance.
HowoftenmustIchargethebatteries?
Many factors come into play when deciding how often to charge the batteries.You may use your power chair all day on a
daily basis or you may not use it for weeks at a time.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
33
V I . B A T T E R I E S A N D C H A R G I N G
! Daily Use
If you use your power chair on a daily basis, charge the batteries as soon as you are finished using your power chair.
Your power chair will be ready each morning to give you a full day’s service. It is recommended that you charge the
batteries 8 to 14 hours after daily use.
! InfrequentUse
If you use your power chair infrequently (once a week or less), you should charge the batteries at least once per week
for 12 to 14 hours.
NOTE: Keep your batteries fully charged and avoid deeply discharging your batteries. Do not charge the
batteries for more than 24 hours at a charging cycle.
How can I get maximum range or distance per charge?
Rarely do you have an ideal driving situation such as smooth, flat, hard terrain with no wind, hills, or curves. More often you
are presented with hills, sidewalk cracks, uneven and loosely packed surfaces, curves, and wind.All of these factors will
affect the distance or running time per battery charge. Below are a few suggestions for obtaining the maximum range per
charge:
! Always charge the batteries fully prior to your trip.
! Plan your trip in advance to avoid inclines if possible.
! Limit baggage weight to essential items.
! Try to maintain an even speed and avoid stop-and-go driving.
What type of batteries should I use?
We recommend deep-cycle batteries that are sealed and maintenance free. BothAGM and Gel-Cell are deep-cycle
batteries that are similar in performance. Refer to the specifications table for more information regarding the batteries used
with your power chair.
WARNING! Corrosive chemicals contained in batteries. Use only AGM or Gel-Cell
batteries to reduce the risk of leakage or explosive conditions.
Why do my new batteries seem weak?
Deep-cycle batteries employ a much different chemical technology than that used in car batteries, nickel-cadmium (nicads),
or in other common battery types. Deep-cycle batteries are specifically designed to provide power, drain down their
charge, and then accept a relatively quick recharge.AGM and Gel-Cell batteries should be charged as often as possible.
They do not have a “memory” like nickel-cadmium batteries.
We work closely with our battery manufacturer to provide a battery that best suits your power chair’s specific demands.
Fresh batteries arrive regularly at Pride and are promptly shipped with a full charge. During shipping, the batteries encoun-
ter temperature extremes that may influence initial performance. Heat robs the charge from the battery, and cold slows the
power available and extends the time needed to recharge the battery (just as with a car battery).
It might take a few days for the temperature of the battery to stabilize and adjust to its new ambient temperature. More
importantly, it will take a few “charging cycles” (a partial drain— then a full recharge) to establish the critical chemical
balance that is essential to the battery’s peak performance and long life. It will be well worth it to take the time to break in
your battery properly.
NOTE: The useful life of a battery is quite often a reflection of the care it receives.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V I . B A T T E R I E S A N D C H A R G I N G
How can I ensure maximum battery life?
Afully charged deep-cycle battery will provide reliable performance and extended battery life. Keep your power chair’s
batteries fully charged whenever possible. Batteries that are regularly and deeply discharged, infrequently charged, or
stored without a full charge may be permanently damaged, causing unreliable power chair operation and limited battery life.
NOTE: If the need is urgent, then it is acceptable to occasionally use the power chair before the batteries are
fully charged.
How should I store my power chair and its batteries?
If you do not use your power chair regularly, we recommend maintaining battery vitality by charging the batteries at least
once per week.
If you do not plan on using your power chair for an extended period, fully charge the batteries prior to storage. Disconnect
the battery harnesses and store the power chair in a warm, dry environment.Avoid temperature extremes, such as freezing
and excessively hot conditions, and never attempt to charge a frozen battery.Acold or frozen battery should be warmed
for several days prior to recharging.
What about public transportation?
AGM and Gel-Cell batteries are designed for application in power chairs and other mobility vehicles. These batteries are
FederalAviationAdministration (FAA) approved, allowing safe transportation on aircraft, buses, and trains, as there is no
danger of spillage or leakage. We suggest you contact the carrier’s ticket counter in advance to determine that carrier’s
specific requirements.
What about shipping?
If you wish to use a freight company to ship your power chair to your final destination, repack your power chair in the
original shipping container and ship the batteries in separate boxes.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
35
V I I . C A R E A N D M A I N T E N A N C E
CARE AND MAINTENANCE
Your Quantum 6000Z Series is a sophisticated power chair. Like any motorized vehicle, it requires routine maintenance
checks. You can perform some of these checks, but others require assistance from your Quantum Rehab Specialist.
Preventive maintenance is very important. If you follow the maintenance checks in this section as scheduled, you can help
ensure that your power chair gives you years of trouble-free operation. If you have any doubt as to your power chair’s care
or operation, contact your Quantum Rehab Specialist.
WARNING! Do not service the power chair when the seat is occupied.
Your power chair, like most electrical equipment, is susceptible to damage from the elements.Avoid damp areas of
any kind.
WARNING! Direct or prolonged exposure to water or dampness could cause the power chair to
malfunction electronically and mechanically. Water can cause electrical components to corrode
and the chair’s frame to rust. Power chairs should be examined periodically for signs of corrosion
cause by water exposure, bodily fluids exposure, or incontinence. Damaged components should
be replaced or treated immediately.
Should your power chair come in contact with water:
1. Dry your power chair as thoroughly as possible with a towel.
2. Allow your power chair to sit in a warm, dry place for 12 hours to allow unseen water to evaporate.
3. Check the joystick operation and the brakes before using your power chair again.
4. If any inconsistencies are found, take your power chair to your Quantum Rehab Specialist. Power chairs that are
frequently exposed to sources of water, such as incontinence, should be inspected often for corrosion and electronic
components may need to be replaced frequently.
Temperature
! Some of the parts of your power chair are susceptible to extreme changes in temperature.Always keep your power
chair between the temperatures of 18° F/-8° C and 122° F/50° C.
! In extremely cold temperatures the batteries may freeze. The specific temperature at which they freeze depends on a
number of factors, such as battery charge, usage, and composition of the batteries (e.g.,AGM or Gel-Cell).
! Temperatures above 122° F/50° C may cause your power chair to operate at a reduced speed. This reduced speed
is a safety feature built into the controller that helps prevent damage to the motor and other electrical components.
General Guidelines
! Avoid knocking or bumping the controller, especially the joystick.
! Avoid prolonged exposure of your power chair to extreme conditions, such as heat, cold, or moisture.
! Keep the controller clean.
! Check all connectors to ensure that they are all tight and secured properly.
! Make sure the pneumatic tires are inflated to 35 psi (2.4 bar) if equipped with pneumatic tires..
WARNING! Make sure your tires are inflated to 35 psi (2.4 bar). Do not underinflate or overinflate
your tires. Low pressure may result in loss of control, and overinflated tires may burst. Overinflating
tires can cause them to explode.
WARNING! Do not use a high pressure hose to inflate your tires.
! Use a rubber conditioner on the tire sidewalls to help preserve them.
WARNING! Never use a rubber conditioner on the tread area of the tires; doing so may make the
tires slippery and cause your power chair to skid.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V I I . C A R E A N D M A I N T E N A N C E
! The body shroud has been sprayed with a clear sealant coating. You can apply a light coat of car wax to help it retain
its high-gloss appearance.
! Check all electrical connections. Make sure they are tight and are not corroded. Batteries must sit flat within the battery
boxes and battery well frame with the battery terminals facing inward toward each other. Refer to the battery wiring
label for the correct wiring layout.
WARNING! Even though the power chair has passed the necessary testing requirements
for ingress of liquids, you should keep electrical connections away from sources of
dampness, including direct exposure to water or bodily fluids and incontinence. Check
electrical components frequently for signs of corrosion and replace as necessary.
! All wheel bearings are prelubricated and sealed. They require no subsequent lubrication.
Daily Checks
! With the controller turned off, check the joystick. Make sure it is not bent or damaged and that it returns to the neutral
position when you release it. Check the rubber boot around the base of the joystick for damage. Visually inspect the boot.
Do not handle or try to repair it. See your Quantum Rehab Specialist if there is a problem.
! Visually inspect the controller communications cable. Make sure that it is not frayed, cut, or has any wires exposed.
See your Quantum Rehab Specialist if there is a problem.
! Check for flat spots on solid tires. Flat spots could adversely affect stability.
Weekly Checks
! Disconnect and inspect the controller cable and the charger harness from the power base. Look for corrosion. Contact
your Quantum Rehab Specialist if necessary.
! Ensure that all parts of the controller system are securely fastened to your power chair. Do not overtighten any screws.
! Check for proper tire inflation. There should be 35 psi (2.4 bar) in each tire. If a tire does not hold air, see your
Quantum Rehab Specialist for replacement of the tube.
! Check the brakes. This test should be carried out on a level surface with at least 3 feet (1 meter) ofclearance around your
powerchair.
To check the brakes:
1. Turn on the controller and turn down the speed level of your power chair.
2. After one second, check the battery condition meter. Make sure that it remains on.
3. Slowly push the joystick forward until you hear the electric brakes click. Immediately release the joystick.You must be
able to hear each electrical brake operating within a few seconds of joystick movement. Repeat this test three times,
pushing the joystick backward, then left, and then right.
Monthly Checks
! Check for drive tire wear. See your Quantum Rehab Specialist for repair.
! Check the caster wheels for wear. Replace them as necessary.
! Check the caster forks for damage or fluttering which indicates that they may need to be adjusted or have the bearings
replaced. See your Quantum Rehab Specialist for repair.
! Keep your power chair clean and free of foreign material, such as mud, dirt, hair, food, drink, etc.
Yearly Checks
Take your power chair to your Quantum Rehab Specialist for yearly maintenance, especially if you use your power chair
on a daily basis. This helps ensure that your power chair is functioning properly and helps prevent future complications.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
37
V I I . C A R E A N D M A I N T E N A N C E
Storage
Your power chair should be stored in a dry place, free from temperature extremes. When storing, disconnect the batteries
from the power chair. SeeVI. “Batteries and Charging.”
WARNING! If you fail to store the unit properly, the frame can rust and the electronics can be
damaged.
Batteries that are regularly and deeply discharged, infrequently charged, stored in extreme temperatures, or stored without
a full charge may be permanently damaged, causing unreliable performance and limited service life. It is recommended that
you charge the batteries periodically throughout periods of prolonged storage to ensure proper performance.
You may wish to place several boards under the frame of your power chair to raise it off of the ground during periods of
prolonged storage. This takes the weight off the tires and reduces the possibility of flat spots developing on the areas of the
tires contacting the ground.
Disposal of Your Power Chair
Your power chair must be disposed of according to applicable local and national statutory regulations. Contact your local
waste disposal agency or Quantum Rehab Specialist for information on proper disposal of power chair packaging, metal
frame components, plastic components, electronics, and batteries.
Cleaning and Disinfection
! Use a damp cloth and mild, non-abrasive cleanser to clean the plastic and metal parts of your power chair. Avoid using
products that may scratch the surface of your power chair.
! If necessary, clean your product with an approved disinfectant. Make sure the disinfectant is safe for use on your
product before application.
WARNING! Follow all safety instructions for the proper use of the disinfectant and/or cleaning
agent before applying it to your product. Failure to comply may result in skin irritation or premature
deterioration of upholstery and/or power chair finishes.
WARNING! Never hose off your power chair or place it in direct contact with water. Your power
chair has a painted, ABS plastic body shroud that allows it to be easily wiped clean with a damp
cloth.
WARNING! Never use any chemicals to clean a vinyl seat, as they may cause the seat to become
slippery or dry out and crack. Use soapy water and dry the seat thoroughly.
Wheel Replacement
If you have pneumatic tires and you have a flat tire, you can replace the tube. If your chair is equipped with a solid tire
insert, then you must replace the entire wheel assembly. Replacement tires, tubes, and wheel assemblies are readily avail-
able through your Quantum Rehab Specialist.
WARNING! The wheels on your power chair should only be serviced or replaced by a Quantum
Rehab Specialist or a qualified technician.
WARNING! Be sure that the power to the controller is turned off and the power chair is not in
freewheel mode before performing this procedure.
WARNING! When changing a tire, remove only the center lug nut and washer, then remove the
wheel. If any further disassembly is required, deflate the tire completely or it may explode.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V I I . C A R E A N D M A I N T E N A N C E
TIRE
TUBE
FRONT RIM HALF
SCREWS
WHEELHUB
REAR RIM HALF
LUG NUTS
Figure 27. Quantum 6000Z Series DriveWheel
Figure 28. Quantum 6000Z Series DriveWheel Disassembled
Follow these easy steps for a quick and safe repair for both pneumatic and solid tires:
1. Turnoffthepowertothecontroller.
2. Setthepowerchairuponblocks.
3. Ifyouarechangingapneumatictire,completelydeflateitbeforeremovingthewheel.
4. Removethe(5)lugnutsfromthewheelhub.Seefigure27.
5. Pullthewheeloffofthehub.
6. Removethescrewsandseparatethefrontandrearrim. Seefigure28.
7. Removethe old tube from thepneumatic tire and replace it with a newtube or replacethe entire assemblyifit is a solid tire.
8. Screwtogetherthetworimhalves.
9. Slidethewheelbackontothehub.
10. Reinstallthefive(5)lugnutsontothewheelhubandtighten.
11. Inflatethepneumatictireto35psi(2.4bar).
12. Removethepowerchairfromtheblocks.
Battery Replacement
A battery wiring diagram is printed on a decal located the power base. See VI. “Batteries and Charging” for correct
battery specifications.
WARNING! Battery posts, terminals, and related accessories contain lead and lead
compounds. Wear goggles and gloves when handling batteries and wash hands after
handling.
WARNING! The batteries in your power chair should only be serviced or replaced by a Quantum
Rehab Specialist or a qualified technician.
WARNING! Do not replace batteries when seat is occupied.
WARNING! Power chair batteries are heavy. See specifications table. If you are unable to lift that
much weight, be sure to get help.
WARNING! Use proper lifting techniques and avoid lifting beyond your capacity. Do not mix or
match new and old batteries. If you encounter a situation where one battery needs to be replaced,
then replace both batteries. Refer to specifications table in this manual and the manual supplied
with the battery charger for recommended type and capacities.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
39
V I I . C A R E A N D M A I N T E N A N C E
BATTERY WIRING DIAGRAM
FRONT COVER
REARSHROUD
REARSHROUDFASTENER
(OPPOSITE SIDE NOT SHOWN)
RELEASEHANDLES
FRONT BATTERY
REAR BATTERY
Figure 29. Battery Installation
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V I I . C A R E A N D M A I N T E N A N C E
To replace the batteries:
1. Turn off the power to the controller.
2. Make sure that the power chair is in drive mode. See III “Your Power Chair.”
3. Remove the foot platform by squeezing the release handles (see figure 29) and lifting the foot platform bracket up
and away from the power base.
4. Disconnect the quick release battery connectors. See figure 7.
5. Remove the batteries.
6. Disconnect the battery harness from each battery.
WARNING! Make sure you tighten the fasteners so that the connections are secure.
7. Connect the battery harness to the new front battery according to the battery wiring diagram. See figure 29.
8. Connect the battery harness to the new rear battery according to the battery wiring diagram. See figure 29.
9. Install the new batteries.
10. Reinstall the front cover and foot platform.
11. Charge the batteries. See VI. “Batteries and Charging.”
When to See Your Quantum Rehab Specialist for Service
The following symptoms could indicate a serious problem with your power chair. If necessary, contact your Quantum
Rehab Specialist. When calling, have the model number, serial number, nature of the problem, and the error code if
available.
! Motor noise
! Frayed harnesses
! Cracked or broken connectors
! Uneven wear on any of the tires
! Jerky motion
! Pulling to one side
! Bent or broken wheel assemblies
! Does not power up
! Powers up, but does not move
Corrective Maintenance
If the battery condition meter does not light up when you turn on the power:
! Check the harness connections. Make sure they are tight.
! Check the circuit breaker. Reset it if necessary.
! Check the battery connections.
If the above conditions prove normal, you can load test the batteries with a battery load tester. These testers are available
at automotive parts stores. Disconnect both batteries before load testing and follow the directions that come with the load
tester. If either one of the batteries fails the load test, replace both of them. If your power chair still does not power up,
contact your Quantum Rehab Specialist.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
41
V I I I . W A R R A N T Y
LIFETIME LIMITED WARRANTY
For the lifetime of your power chair from the date of purchase, Pride will repair or replace at our option to the original
purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Pride to be
defective in material and/or workmanship:
Structural frame components, including:
! Main Frame
! Fixed-position seat post
TWO-YEAR LIMITED WARRANTY
For two (2) years from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
Electronic components, including:
! ChargerAssembly
! Controller
Main frame assemblies, including:
! Anti-tip forks ! Caster forks
! Caster beam ! Metal seat framing
! Joystick
Other components, including:
! Foot riggings
! Electrical Harness ! Foot rigging mounting brackets
18-MONTH LIMITED WARRANTY
For eighteen (18) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free
of charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Motor/gearbox assembly ! Power seat actuator
ONE-YEAR LIMITED WARRANTY
For one (1) year from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Accessories
! Brakes (electronic function ONLY)
SIX-MONTH LIMITED WARRANTY
For six (6) months from the date of purchase, Pride will repair or replace at our option to the original purchaser, free of
charge, any of the following parts found upon examination by an authorized representative of Pride to be defective in
material and/or workmanship:
! Bearings and bushings
! Plastic components, except body
The battery is covered by a separate six-month warranty, provided by the battery manufacturer. The batteries are not
warranted by Pride.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
V I I I . W A R R A N T Y
RECONDITIONED UNITS WARRANTY
All reconditioned units are covered by a six-month warranty from Pride effective from the date of purchase.
WARRANTY EXCLUSIONS
This warranty does not extend to those items which may require replacement due to normal wear and tear.
! ABS Plastic shrouds
! Motor brushes
! Upholstery and seating
! Brake Pads
! Tires and tubes
! Fuses/Bulbs
! Circumstances beyond the control of Pride
! Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically authorized, IN
ADVANCE, by Pride Mobility Products Corporation
! Repairs and/or modifications made to any part without specific consent from Pride
Exclusions also include components with damage caused by:
! Contamination
! Abuse, misuse, accident, or negligence
! Battery fluid spillage or leakage
! Commercial use, or use other than normal
! Improper operation, maintenance, or storage
NOTE: Gradual deterioration in performance because the battery has been left in a discharged state, left in
cold conditions for an extended period of time, or worn out through heavy use is not covered.
SERVICE CHECKS AND WARRANTY SERVICE
Warranty service must be performed by a Quantum Rehab Specialist. Do not return faulty parts to Pride without prior
written authorization.All transportation costs and shipping damage incurred while submitting parts for repair or replacement
are the responsibility of the purchaser.
Failure to follow the instructions, warnings, and notes in the owner’s manual and those located on your Pride product can
result in personal injury or product damage and will void Pride’s product warranty.
There is no other express warranty.
IMPLIED WARRANTIES
Implied warranties, including those of merchantability and fitness for a particular purpose, are limited to one (1) year from
the date of purchase and to the extent permitted by law.Any and all implied warranties are excluded. This is the exclusive
remedy. Liabilities for consequential damages under any and all warranties are excluded.
Some states do not allow limitations on how long an implied warranty lasts or do not allow the exclusion of limitation
incidental or consequential damages. The above limitation or exclusion may not apply to you.
This warranty gives you specific rights, and you may also have other rights which vary from state to state.
Please fill out and return the product registration card to Pride. This will aid Pride in providing the best possible technical
and customer service.
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
43
N O T E S
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
N O T E S
Quantum 6000Z Series
Download from Www.Somanuals.com. All Manuals Search And Download.
45
N O T E S
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Quantum 6000Z Series
Quality Control - Quantum 6000Z Series
Inclusion of all Parts
Joystick Serial Number
Controller Serial Number
Left Motor Serial Number
Right Motor Serial Number
Fit and Finish
Performance
Pride keeps a more detailed report on file at the factory.
Date Inspected
Inspector
*I NFMANU3447*
Product Serial #
Download from Www.Somanuals.com. All Manuals Search And Download.
|