Included Hardware
M4 x 12mm Phillips
Head Screw
(Qty 4)
¾” Spacer (Qty 4)
INSTALLATION GUIDE: XUA-1330L
M4 x 30mm Phillips
Head Screw
(Qty 4)
Victory LCD Wall Mounting System
2” Wood Screw
(Qty 2)
The Victory LCD Mounting System is designed for secure installation of LCD displays of up to
40 lbs. in weight.
Bubble Level (Qty 1)
Tool List
Warning Statements
Phillips Head Screw Driver
Electronic Stud Finder
THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A MAXIMUM
WEIGHT OF 40 LBS. IF NOT, THE WALL MUST BE REINFORCED. PROPER
INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS OUTLINED IN
THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO. FAILURE TO DO SO
COULD RESULT IN SERIOUS PERSONAL INJURY OR EVEN DEATH.
WARNING:
Allen Wrenches (3mm and 4mm – supplied)
Portable Drill
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE INSTALLATION
OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR THE INSTALLATION
PROCEDURE TO PREVENT PERSONAL INJURY.
WARNING:
WARNING:
¼” Masonry Bit for Concrete Installation
NOTE: The included level may be permanently attached to the
wall plate by inserting the level into the receptacle on
the back of the wall plate.
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS
SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE INSTALLATION
INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY AND PROPERTY
DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE
LOCATION FOR FUTURE REFERENCE.
Wood Stud Installation
NOTE:
Using a wood stud finder, locate the stud centers
behind the wall. Once found, make a pencil marking
on the center of the wood studs. Once the mark is
made, it is strongly recommended that a pilot hole be
drilled with a 1/8” drill bit.
A secure structure must support the weight or load of the display. When mounting to a wall that
contains wooden studs, dead center of the wooden stud must be confirmed prior to installation.
1. Place the back plate against the wall with the hook towards
the bottom.
2. Secure the back plate using one (1) 2” wood screw.
3. Using the integrated bubble guide, carefully adjust the back
plate until it is level.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to
do so could result in damage to the display and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct
heat energy. Failure to do so may result in damage to the display and could increase the risk of
fire.
4. Attach the remaining 2” wood screw into the back plate and
tighten.
At least two qualified people should perform the installation procedure. Injury and/or damage
can result from dropping or mishandling the display.
Concrete Installation
NOTE: ¼” x 2 ¼” Threshold anchors must be used for concrete
installation. They can be purchased at your local
hardware store.
1. Place the back plate against the wall with the hook towards
the bottom.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be
installed on any surface other than wooden studs, use suitable hardware (which is
commercially available).
2. Level and mark with a pencil the two mounting points found
on the back plate.
Contact Victory Mounts with any technical / installation questions.
3. Next, drill two holes using an electric drill and ¼” masonry bit.
4. Insert the threshold anchors into the holes that were drilled in
the wall.
NOTE: If necessary, use a hammer to lightly tap each anchor
into place so that they are flush with the wall. Once
mounted in the wall, unscrew the slotted cap off of
the threshold screw.
Threshold
Anchor
5. Once the anchors are in place, set the back plate back over
the concrete anchors.
6. Using a Slot Head screw driver, attach the back plate by
threading the two slotted caps onto the threaded insert that
is recessed into the wall.
7. Make sure all screws are snug, but be careful not to over-
tighten them.
Slotted Cap
Threaded Insert
Threshold Anchor
Download from Www.Somanuals.com. All Manuals Search And Download.
|