ViewSonic by Premier Mounts
INSTALLATION INSTRUCTIONS
WMK-027
Universal Short Throw Wall Mount
EUROPE
Swallow House,
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
Phone: 800-368-9700
Fax: 800-832-4888
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2009
9530-070-353-00
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Parts List
This mount is shipped with all proper installation hardware and components. Make sure that none of these parts are
missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Premier Mounts (800) 368-9700.
Extension Hardware Pack
M6 x 12mm Security (Qty 2)
1/4” Flat Washer (Qty 2)
1/4” Nylon Spacer
(Qty 2)
Extension Arm - Optional (Qty 1)
included with the WMK-027
Wall Plate (Qty 1)
Arm Assembly (Qty 1)
Non-Security (Qty 1)
Security (Qty 1)
5/16 x 3” Lag
5/16 Flat
End Cover (Qty 1)
Upper Mounting Bracket
Inner Slide Plate (Qty 1)
M6 Set Screws
Bolts (Qty 4) Washers (Qty 4)
(Qty 1)
M5
M3
M5 x 12mm Security Head
Screws (Qty 11)
3/8” Concrete Wedge
M6 x 12mm Security
Head Screws (Qty 4)
Back Plate
Covers (Qty 2)
Security Wrenches
(PDS-PLUS Hardware Pack)
Anchors (Qty 4)
PDS-PLUS Projector
Mount
Installation Tools (not supplied)
Electronic Stud Finder
Level
Drill
Phillips Screwdriver
1/4” Drill Bit
1/2” Socket and Socket
Wrench
3/8” Masonry Drill Bit
Installation Instructions
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Determining the Installation Height
In order to determine the installation height and throw distance, the PDS-PLUS projector bracket must be mounted to the
projector. Please refer to the PDS-PLUS Installation Instructions prior to performing the following steps.
Refer to the projectors User’s Manual to determine the offset of the projector lens to the top of the screen/whiteboard.
PDS-PLUS Bracket
Projector
Lens
Step 1. Measure distance from center of lens to the top of the PDS-PLUS bracket.
Step 2. Add the distance from the ground to the top of the screen (A), the recommended offset from the projector manual (B),
the measurement from Step 1 (C), and then add 1.5”.
(Example: A + B + C + 1.5” = ?)
Step 3. Measure the calculated distance from the top edge of the viewable area of the screen/whiteboard and mark the wall. This mark
will represent the lower edge of the wall plate.
Mark
Top of Screen
Legend
A -
Distance from ground to the top of the
screen/whiteboard (viewable area).
B -
Manufacturers recommended offset
measurement. This measurement will be
listed in the Users Manual.
C -
Center of the lens to the top of the
PDS-PLUS bracket.
Add 1.5” to the calculated total. This total distance
will be the location for the bottom rail on the wall
plate.
Ground
Page 4
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Wood Stud Installation
Do NOT over-tighten lag bolts when attaching the mount to the wall. Improper installation may result in personal injury
or damage to property.
DEAD CENTER MUST BE LOCATED ON THE STUD FOR CORRECT AND SAFE INSTALLATION.
Wood Stud
Marking
(from page 4)
Marking
Wood Stud
Stud finder
Wall
Plate
Step 1. Use an electronic stud finder
(commercially available) to
locate the center of the stud
that is in the wall.
Step 2. Use a pencil to mark the first
Step 3. Use the level to make sure
the wall plate is level from
top to bottom. After
determining the desired
viewing height, place the
wall plate over the first hole
and use a pencil to mark the
rest of the holes.
mounting hole, just above
your height mark (from
page 4).
Lag Bolt and
Flat Washer
Drill
Marking
Wall Plate
Covers
Socket
Wall
Plate
Step 4. Once the holes have been
marked, use a 1/4” drill bit
and portable drill to drill the
pilot holes.
Step 5. After the pilot holes have
been drilled, use four (4)
5/16” x 3” lag bolts and four
(4) flat washers to mount the
wall plate to the wooden
stud. Use a 1/2” socket and
socket wrench to finish this
step.
Step 6. Insert and gently tap the wall
plate covers into place.
Completed Installation
Installation Instructions
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Solid Surface Installation
Concrete drill bits are commercially available.
Hammer
Marking
Drill
3/8” Drill Bit
Wedge Anchor
Pilot Hole
Step 3. Use a 3/8” drill bit to drill the
mounting holes where the
marks were made with a
pencil.
Step 1. Place the wall plate against
the wall and use a level to
make sure the wall plate is
level from top to bottom.
Step 2. Use a pencil to mark the
location of the mounting
holes.
Step 4. Once the holes have been
drilled, place the concrete
wedge anchors into the
hole. Using
a
hammer,
gently tap into place.
Step 5. Once the wedge anchors
have been inserted into the
mounting holes, remove the
nut and flat washer from the
wedge anchor.
Nut and Washer
Seated Wedge
Anchor
Wall Plate
Covers
Socket
Wall Plate
Wall Plate
Step 7. Place the flat washer and
nut onto the wedge anchor
and tighten using a socket
and socket wrench. Do not
overtighten.
Step 6. Place the wall plate over the
wedge anchors once the
wedge anchors have been
correctly inserted into the
mounting surface.
Step 8. Insert and gently tap the wall
plate covers into place.
Completed Installation
Page 6
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Utilizing the Storage Feature
The storage feature may be used to store electronic components. There is an accessible door on each side of the storage enclosure. It may
be securely held shut with the use of four (4) M5 x 12mm security head screws. It may be easiest to pre-wire all cables down the arm (or
extension) at this time (see Page 11).
Security
Wrench
M5 x 12mm
Security Screw
Electronic
Components
Electronic
Components
Door
Door
Step 4. Close the storage door and secure using two
(2; 1 upper and 1 lower) M5 x 12mm security
head screws. Tighten using a security wrench.
Repeat this process for the other side as well.
Step 1. Open the storage door that is located on the side of
the wall plate.
Step 2. Place the electronic components inside the storage
enclosure.
Step 3. Make all electronic connections at this time.
Attaching the Projector Arm
Mounting Hook Cutout
Mounting Hooks
Wall Plate
Projector Arm
Step 1. Locate the mounting hook cutout on the top of the wall plate.
Step 2. Tilt the arm slightly and gently insert the mounting hooks into the mounting hook cutouts.
Step 3. Slowly lower and let the projector arm rest against the wall plate.
Installation Instructions
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
MAKE SURE THE PROJECTOR ARM IS FULLY SEATED BEFORE RELEASING THE UNIT.
Lock Mounting Point
M5 x 12mm Security Head Screw
Screwdriver/Security Wrench
Step 4. Locate the two (2) lock mounting points on the projector arm. These two points will be aligned with the lock mounting
points on the wall plate.
Step 5. Using a security wrench, insert and tighten two (2) M5 x 12mm security head screws.
DO NOT OVERTIGHTEN THE SCREWS.
Throw Distance Calculation
Please review the Operator’s Manual that came packaged with your projector before attaching the upper mounting
bracket. The correct throw distance (the distance from the projector to the screen) must be determined prior to mounting
the projector.
Step 1. Refer to the projectors Users Manual to
determine the distance from the lens to the
front of the screen.
Calculations
X = Manufacturers recommended
throw distance
Step 2. Measure the distance from the front of the
lens to the center of the PDS-PLUS (see
diagram).
Z = Distance from wall to face of
whiteboard/screen
Front Lens
Front Mounted Lens
Front Lens Throw Distance =
(X + Y + Z)
For front-mounted lenses, add distance (Y)
to distance listed in projector Users Manual.
Rear Mounted Lens
For rear-mounted lenses, subtract disance (Y) from
the distance listed.
Rear Lens Throw Distance =
(X - Y + Z)
Step 4. Use a tape measure to mark the appropriate
distance on the WMK-027. This
will be where the center of the mounting
bracket will be located.
Rear Lens
If installing WMK-027, please refer
to Page 10 before continuing.
Page 8
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Upper Mounting Bracket Installation
Step 1. Insert the inner slide plate into the projector
arm.
Projector Arm
Step 2. Determine which adjustment slot will be
best for the projector placement.
Step 3. Raise the upper mounting bracket into
position.
Step 4. Align the mounting holes of the upper
projector plate with the mounting holes of
the inner slide plate.
Step 5. Secure and finger-tighten two (2)
M6 x 12mm security head screws.
Adjustment
Slot
Inner Slide
Plate
Upper Mounting
Bracket
M6 x 12mm
Security Screw
Calculated
Throw Distance
Step 6. Once the correct throw distance has been
determined, use the security wrench
(supplied) to tighten the mounting screws.
Do not overtighten the screws.
Security
Wrench
Installation Instructions
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Extension Arm Installation (Optional)
Please see the Operator’s Manual to determine the correct throw distance (the distance from the projector to the screen)
must be determined prior to mounting the projector.
If the extension arm was purchased at a later date, the end cover must be removed prior to installing the extension arm.
WMK-027
1/4” Flat
Washers
1/4” Nylon
Spacer
M6 x 12
Security Screw
Security
Wrench
Upper
Mounting
Bracket
Extension Arm
Step 1. Slide the extension arm into the open end of the WMK-027 (the front of the mount).
Step 2. Attach the upper mounting bracket directly to the extension using two (2) M6 x 12mm set screws (see page 8).
Step 3. Adjust length so that the center of the upper mounting bracket matches the throw distance calibration.
Step 4. Line up the mounting holes on the extension arm with the mounting slots on the WMK-027.
Step 5. Using a screwdriver, insert and tighten two (2) M6 x 12mm security head screws, 1/4” flat washers and 1/4” nylon spacers.
Step 6. Attach the PDS-PLUS (see page 10).
Please review the Operator’s Manual that
came packaged with the PDS-PLUS before
attaching the PDS-PLUS to the upper mounting
bracket.
Base Box Installation
Projector Mount
M6 x 12mm Screws
Security Wrench
Base Box
Step 1. Raise the base box projector mount to the upper mounting bracket.
Step 2. Align the two (2; one each side) mounting holes.
Step 3. Using a screwdriver/security wrench, insert and tighten two (2) M6 x 12mm security head screws. Do not over tighten the
screws.
Step 4. Attach the projector to the base box, referring to the PDS-PLUS Installation Instructions for final adjustments.
Page 10
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Cable Management
WMK-027
Electronic Components
Electronic Components
WMK-027
Electronic
Cables
Components
Cable Opening
Cable Opening
Projector Hook-Ups
Cables
Cable Opening
Projector Hook-Ups
Step 1. The cable access holes are located at the end of the short throw mount and on the wall plate.
Step 2. Route the cables through one end of the WMK-027 and out the other end.
Set Screw Installation (Optional)
The M6 set screw will be used in conjunction with any
standard 1-1/2” NPT or CLS (sold separately).
Step 1. Thread in CLS or any 1-1/2” NPT until
securely fastened.
Upper Mounting
Bracket
Step 2. Thread in one (1) M6 x 6mm set screw.
Step 3. Use an M3 security wrench to tighten the M6
set screw (included in the PDS-PLUS
hardware).
M6 Set Screw
M3 Security
Wrench
Installation Instructions
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Technical Specifications
All measurements are in inches(mm).
Page 12
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
WMK-027
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-
PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN
PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-
ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-
ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Installation Instructions
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
|