Premier Mounts TV Mount PWM F110 User Manual

INSTALLATION MANUAL  
PWM-F110  
Premier Mounts  
3130 E. Miraloma Avenue  
Anaheim, CA 92806  
Phone: (800) 368-9700  
Fax: (800) 832-4888  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Table of Contents  
Warning Statements ...........................................................................................................................................- 4 -  
Parts List ............................................................................................................................................................- 6 -  
Installation Tools ...............................................................................................................................................- 6 -  
Mounting Bracket Installation ...........................................................................................................................- 7 -  
Wall Stud Location ..........................................................................................................................................- 10 -  
Installing the Flat Panel Display ......................................................................................................................- 14 -  
Technical Specifications ..................................................................................................................................- 16 -  
Warranty ..........................................................................................................................................................- 17 -  
Contact Premier Mounts ..................................................................................................................................- 17 -  
Notes ................................................................................................................................................................- 18 -  
Installation Manual  
Page - 3 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Warning Statements  
Safety Precautions  
This wall mount should be installed by qualified personnel having sufficient skill and competence to install it. Qualified installation  
specialists or your dealer should install the mount and set up the plasma television in order to avoid personal injury or property damage.  
Premier Mounts does not assume liability for injury or damage caused by improper installation, mounting or setup of the plasma  
television, misuse, modification or natural disasters.  
The entire installation instructions should be fully read and understood, including all of the safety symbols and safety precautions, before  
beginning installation. The installation instructions should be read, understood and followed to prevent personal injury or property  
damage. Keep these installation instructions in an easily accessible location for future reference.  
The wall being considered for mounting must be capable of supporting at least five (5) times the weight of 40Kg. If it is not, the wall  
must be reinforced before beginning installation.  
Only use specified parts for the installation of the mounting bracket. Do not use the mounting hardware from any other mount or any  
other source.  
A secured structure wooden stud wall must always support the weight or load of the plasma. Always confirm the center of  
the wood stud before beginning the installation. Failure to do so could result in personal injury and physical damage.  
Avoid installing the plasma in locations where temperatures and humidity are excessively high, or contact with any water or  
vapors possible. This could result in fire, electrical shock and damage to the plasma television. Water will damage the wall  
structure for wall mount installation. The permissible temperature is (0-40ºC) and humidity is (20%-80%).  
The mount is designed to be used on vertical walls only. Do not install near or on doors, angled ceilings, walls, or any other  
installations other than wall mounting. Failure to do so could result in damage and injury. This wall mount is to be used  
only with plasma television. Use with any plasma television other than is prohibited and may cause injury and damage.  
Make sure the plasma mounting area is completely free of internal or external wires, pipes, gas lines, phone lines etc. Failure  
to do so will result in injury and damage to the walls, wiring or piping system.  
Avoid Installations where there is danger of contact with over excessive dust, oil smoke, and tobacco smoke. Failure to do so  
may result in fire or damage to the plasma or its internals.  
Do not block the ventilation holes. Sufficient clearance must be left in the area surrounding the plasma and wall mount to  
avoid blocking the vents and causing the plasma to overheat which could cause a risk of fire. Leave 100mm or more away  
from all of the surrounding four sides for proper airflow.  
Do not install in locations where there is vibration, movement or danger of impact. Failure to do so could result in plasma  
cracking or falling from the wall causing damage and injury.  
Do not install near heater, fireplace, direct sunlight or air conditioning or any other source of direct heat energy. Failure to  
do so may result in damage to the plasma television and could cause a risk of fire.  
It is not necessarily to open the plasma television prior to installation. Never open the plasma or modify the mount. This  
plasma is to be used only as outlined in the installation instruction. Failure to do so may result in damage and injury. If a  
malfunction or problem occurs, contact the nearest dealer.  
At least two qualified people should always perform the installation work. Injury and damage can result from dropping or  
bending the plasma television.  
All six (6) M8 bolts (part B) and quick release sleeves (part A) must be firmly tightened and secured to the plasma television in  
the correct locations. If the quick release sleeves are not properly installed, do not hang the plasma television to the wall  
mount. Damage and Injury could result from the plasma falling down.  
All four (4) Lag bolts must be properly secured to the 450mm wall studs. The lag bolts must always be secured through the  
center of the wood studs. Failure to do so could result in the plasma falling from the wall causing damage to the plasma and  
personal injury.  
All bolts must be properly tightened and secured before installing the plasma display. Failure to do so could result in the  
plasma falling causing damage to the plasma and personal injury.  
Objects on the wall may collect dust quicker than anticipated. Check periodically for dust accumulation. Refer to the plasma  
installation instructions for cleaning instructions.  
Do not play around the plasma or throw any objects near or at the screen. The glass screen is very sensitive and may scratch  
or break or cause the plasma television to fall from the wall causing personal injury and damage.  
Page - 4 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Mount Overview  
This PWM-F110 Plasma Wall Mount may be sold as part of a system or as an independent component. Whichever way it is  
purchased the installer must take care to use only the hardware and components that come included in this package and that it  
only be used in conjunction with the appropriate Plasma Television.  
The PWM-F110 plasma wall mount is to be used to attach a plasma television vertically to an appropriate wall. In order to mount  
the plasma television, it is necessary to attach the enclosed mount using the enclosed hardware to the wall and to use enclosed  
hardware to attach to the back of the plasma television, and then to attach them together.  
As described below, there are three main steps involved in the mounting process:  
1. Attach the six Quick Release Sleeves to the rear of the plasma television.  
2. Position and attach the Plasma Wall Bracket to an appropriate wall.  
3. Lift and attach the plasma television to the Plasma Wall Bracket.  
Read the installation instructions completely in order to ensure a complete understanding of the entire installation procedures  
before beginning the installation process. It is recommended that qualified installers install this product.  
Installation Manual  
Page - 5 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Parts List  
NOTE:  
This wall mount is shipped with all proper installation hardware and components. Make sure that  
none of these parts are missing and/or damaged before beginning installation. If there are parts  
missing and/or damaged, please stop the installation and contact Premier Mounts  
(800) 368-9700 Ext.224.  
5/16” Flat  
Washers  
(8ea)  
Wall Plate  
(2ea)  
Griplates™  
(8ea)  
5/16” x 3”  
Lag Bolts  
(wooden  
studs only)  
– (8ea)  
Mounting  
Brackets  
(left and  
right)  
Wall  
Bumpers  
(2ea)  
M8 x 16mm  
Hex Head  
Bolt (2ea)  
M8 x 20mm  
Phillips  
Head Screws  
(8ea)  
M8 Hex Nut  
(2ea)  
M4 x 16mm  
Phillips  
Head Screws  
(8ea)  
Installation Tools  
Phillips Head Screw Driver  
Pencil  
Soft Material/ Blanket  
Tape Measure  
Drill Gun  
5/16” Socket and Wrench  
Level  
Page - 6 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Mounting Bracket Installation  
NOTE: Proper installation procedure by qualified personnel as outlined in the installation instructions must  
be adhered to. Failure to do so could result in serious personal injury and possible damage to the  
flat panel.  
WARNING: INVERT THE FLAT PANEL AND PLACE IT ON A SOFT, FLAT SUFRACE TO PREVENT DAMAGE  
TO THE FLAT PANEL. USE A BLANKET, FOAM, ETC. FAILURE TO DO SO WILL RESULT IN  
DAMAGING THE FLAT PANEL. DO NOT LAY THE FLAT PANEL ON THE FLOOR WITHOUT ANY  
PROTECTION TO THE GLASS. THE FLAT PANEL IS HEAVY AND FRAGILE. AT LEAST (2)  
QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION OF THIS  
PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE DAMAGE  
TO THE FLAT PANEL.  
1. Once the flat panel is inverted, use a measuring tape to find the center of your flat panel measuring  
from outside to outside of the chassis (Figure 1).  
2. Using a pencil lightly mark the center of your flat panel (Figure 2).  
Measuring tape  
Inverted flat panel  
Top of flat panel  
C
L
C
L
Mark the center  
of the flat panel  
Bottom of flat panel  
Inverted flat panel  
Figure 1  
Figure 2  
Installation Manual  
Page - 7 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
3. If needed, install the nylon spacers to the mounting points on the flat panel (Figure 3).  
4. Lay the left and right mounting brackets (stamped arrows facing out) - (Figure 4).  
Nylon Spacers, If Applicable  
Mounting Brackets  
Center Mark  
Inverted Flat Panel  
Bottom of Flat Panel  
Arrows Facing Out  
Figure 3  
Figure 4  
5. Match the center of viewing guide with the centerline you marked in step 1 (Figure 5).  
6. The mounting brackets are designed with a center of viewing guide on the side of them (Figure 6).  
Page - 8 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Mounting Bracket  
C
L
Bottom of Flat  
Panel  
Center of  
Viewing Guide  
Center of Flat  
Panel  
Bottom of the  
Flat Panel  
Align the Mounting  
Brackets  
Figure 5  
Figure 6  
7. The Griplates™ have M4, M5, M6 and M8 hole patterns to fit the hardware that your flat panel requires.  
EXAMPLE: If your flat panel uses M8 x 20 Phillip screws, use the M8 mounting points (Figure 7).  
8. Once the mounting brackets are aligned, secure the Griplate™ to the flat panel. Use (1) Griplate™ per  
mounting point (Figure 8).  
NOTE:  
The dimples of the top plates have to be facing up and the bottom dimples must be facing down.  
Dimples Facing  
Up  
Screw Driver  
DIMPLES  
FACING UP  
Bottom of Flat  
Panel  
DIMPLES  
FACING UP  
DIMPLES  
FACING DOWN  
M4  
M5  
M6  
M8  
DIMPLES  
FACING DOWN  
3/4"  
Figure 7  
Figure 8  
Installation Manual  
Page - 9 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Wall Stud Location  
1. Using a (commercially available) wood stud finder, locate four 16" or 24" stud centers behind the wall.  
Once found, make a pencil marking on the center of the wood studs (Figure 9).  
NOTE:  
The wall plates have (3) 16" and (1) 24" mounting slot positions (see Technical Specifications on  
Page 17)  
2. Measure from the floor to the desired viewing height and mark the wall.  
NOTE:  
This marking will reference the center of your flat panel display once mounted on the wall  
(Figure 10).  
Mark the wall and  
Wood Stud Finder  
(Commercially available)  
the center of the  
wood studs.  
16”  
16”  
Measure and  
mark the  
viewing height  
desired on the  
wall.  
16”  
Wood studs  
behind the  
wall  
structure.  
Figure 9  
Figure 10  
NOTE:  
Although not depicted in the illustrations shown above, the width of this wall mount will  
encompass four wall studs (three wall studs if 24” apart).  
Page - 10 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
3. To connect the two wall plates, lay them on a flat surface, end to end. Make sure that the holes line up  
(Figure 11).  
4. Insert two (2) M8 x 16mm Hex Head bolts through the two holes and secure with two (2) M8 Hex nuts  
(Figure 11).  
5. Place the bottom portion of the wall plate to the reference line and mark the eight (8) lag bolt  
mounting points through the wall plate slots on the wall.  
6. Level the wall plate with the reference arrow pointing up to the ceiling (Figure 11).  
Mounting Surfaces (Figure 14)  
Wood studs: Drill eight (8) ¼" pilot holes to the marked wall (16”studs, on center – Figure 12).  
Concrete wall: Drill eight (8) 3/8” pilot holes to the marked wall (Figure 18).  
Drill Gun  
Pilot  
Holes  
16"  
Wall Plate  
Mounting  
Slots  
Level  
Wood Studs  
Figure 11  
Figure 12  
NOTE:  
Although not depicted in the illustrations shown above, the width of this wall mount will  
encompass four wall studs (three wall studs if 24” apart).  
Page - 11 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
7. Level and secure the plate to the wall with the reference arrow facing up to the ceiling.  
8. Secure the plate using the eight (8) 5/16" lag bolts and flat washers (supplied) – (Figure 13).  
CAUTION:  
Do not over tighten the lag bolts.  
NOTE:  
Use a minimum diameter of 5/16” x 3” long wood screws.  
Level  
5/16" x 3" lag  
bolts and (4) flat  
washers (4ea)  
Wall Plates  
Figure 13  
NOTE: Although not depicted in the illustrations shown above, the width of this wall mount will encompass  
four wall studs (three wall studs if 24” apart).  
Installation Manual  
Page - 12 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
9. Level and secure the plate to the wall with the reference arrow facing up to the ceiling.  
10. Use a minimum diameter of 5/16” x 2 ¼” large concrete wedge anchors (commercially available) –  
(Figure 14).  
CAUTION:  
Do not over tighten the wedge anchors bolts.  
NOTE:  
Use a minimum diameter of 5/16” x 2 ¼” long wedge anchors (commercially available).  
(4) 5/16" x 2 ¼”  
wedge anchors  
(commercially  
available)  
Wall Plate  
(4) 5/16" x 2 ¼”  
wedge anchors  
(commercially  
available)  
Figure 14  
NOTE: Although not depicted in the illustrations shown above, the width of this wall mount will encompass  
four wall studs (three wall studs if 24” apart).  
Page - 13 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Installing the Flat Panel Display  
WARNING:  
AT LEAST (2) QUALIFIED PERSONNEL ARE STRONGLY RECOMMENDED FOR INSTALLATION  
OF THIS PRODUCT. FAILURE TO DO SO COULD RESULT IN SERIOUS INJURY AND POSSIBLE  
DAMAGE TO THE FLAT PANEL.  
1. Raise the flat panel with the LEFT and RIGHT mounting brackets secured to the flat panel and insert  
the top hooks from each bracket to the rod from the wall plates (Figure 15).  
Wall Plate  
Top  
Figure 15  
Installation Manual  
Page - 14 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
2. Make any lateral shift adjustment and lock it by tightening the two (2) ¼”-20 Phillips screws found on  
the bottom of the mounting brackets. Use the wall bumper to adjust your flat panel.  
CAUTION:  
NOTE:  
Do not over tighten the ¼”-20 screws to the rods (Figure 16).  
To remove the flat panel from the wall, simply back off the ¼”-20 screws using a Phillips  
screwdriver and lift the unit of the wall carefully.  
Wall Plate  
Wall  
Bumper  
Figure 16  
Page - 15 -  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Technical Specifications  
28.000  
(171.2)  
16.000  
1.245  
(406.4)  
(31.75)  
A
C
L
B
5.000 3.500  
(127) (88.9)  
21.790  
(553.4)  
C
L
H
C
16.000  
(406.4)  
D
16.000  
(406.4)  
E
16.000  
(406.4)  
G
F
24.290  
(616.97)  
1.943  
(49.3)  
B
A
H
5.000  
(127)  
21.790  
(553.4)  
F
Figure 17  
Installation Manual  
Page 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Warranty  
Limited Lifetime Warranty  
All Premier Mounts products carry a limited lifetime warranty from ship date against defects in materials and  
workmanship. Premier Mounts is not liable for improper installation that results in damage to mounts,  
adapters, display equipment or personal injury.  
Contact Premier Mounts  
In the event of missing and/or damage equipment, or technical questions, the following information can help  
in the completion of the installation.  
Customer Service – (800) 368-9700 Ext. 224  
Technical Support – [email protected]  
Page 20  
Installation Manual  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PWM-F110  
Notes  
Premier Mounts  
3130 E. Miraloma Avenue  
Anaheim, CA 92806  
Phone: (800) 368-9700  
Fax: (800) 832-4888  
Installation Manual  
Page - 18 -  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Stereo Amplifier CS 800X User Manual
Philips Air Conditioner RAC 18C9 User Manual
Philips Portable DVD Player PD7013 55 User Manual
Philips Portable DVD Player PET835 00 User Manual
Philips Portable Speaker SBC BM100 User Manual
Philips Projection Television 64P8341 User Manual
Philips Speaker System VL1405 User Manual
Pride Mobility Mobility Aid INFINFB2046 User Manual
ProForm Home Gym PFEX441772 User Manual
PYLE Audio Car Stereo System PIFMDK6 User Manual