INSTALLATION INSTRUCTIONS
GB-PIPE1/GB-PIPE1B
Pipe-Mounted Equipment Enclosure
AUSTRALIA, NEW ZEALAND, OCEANIA
EUROPE
Swallow House,
NORTH AMERICA
3130 East Miraloma Avenue
Anaheim, CA 92806 USA
USA and Canada –
(DISTRIBUTOR)
P.O. Box 295
Shilton Industrial Estate,
Shilton, Coventry, England CV79JY
Phone: +44 (0) 2476 614700
Fax: +44 (0) 2476 614710
Mordialloc Victoria 3195
Australia
Phone: 039586 6330
Phone: 800-368-9700
Fax: 800-832-4888
Other Locations – Phone: (001)-714-632-7100; Fax: (001)-714-632-1044
©Premier Mounts 2008
9534-004-003-00
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
Parts List
This accessory is shipped with all proper installation hardware and components. Make sure that none of these parts
are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop the
installation and contact Premier Mounts (800-368-9700).
Equipment Tray (Qty 1)
Side Panel (Qty 2)
Upper Plate (Qty 1)
M5 x 10mm Security Head Screw (Qty4)
M4 x 8mm Security Head Screw (Qty 10)
M8 x 12mm Security Head Screw (Qty8)
Installation Tools
M5 Security Wrench
M3 Security Wrench
Installation Instructions
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
GB-PIPE1 Installation
The GB-PIPE1 is designed for use with either a standard piece of 1-1/2” NPT pipe or any available ceiling mount adapter
from Premier Mounts. Please refer to the ceiling mount adapter installation instructions when mounting.
Unpack the Gear Box and review any WARNING statements that apply to the installation. Select the desired location for
the GB-PIPE1.
1-1/2” NPT
Set Screw
M3 Security
Wrench
Upper Plate
Step 1. Determine where the GB-PIPE1 will be
Step 4. Use an M3 security wrench to tighten the
located.
set screw.
Step 2. Install your 1-1/2” NPT or ceiling adapter.
Step 3. Attach the upper plate to the NPT or
adapter by rotating counter-clockwise.
The upper plate must rotate onto the
threads at least four (4) complete
rotations.
Pipe
Electronic
Component
Cables
Step 5. At this time, run all existing cables through
the pipe and down through the upper
plate.
At this time, you may pre-install your
electronic components in the equipment
tray.
Page 4
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
M4 x 10mm
Security
Screws
Upper Plate
Spring Loaded
Nuts
Electronic Components
Mounting Hole
Step 7. Line up the mounting holes with the
threaded shaft of the spring loaded nuts.
Step 6. Lift the equipment tray into position.
Step 8. Once the holes are lined up, press down
on the spring loaded nuts and tighten.
Step 9. Insert and tighten two (2) M4 x 10mm
security screws on the upper plate.
1-1/2” NPT Installation
Before attaching the lower 1-1/2” NPT, it is strongly recommended that all connections in the equipment tray be made at
this time. Once the connections are made, feed the cables through the plate hole and then through the 1-1/2” NPT. Please
read instructions below to complete the installation.
1-1/2” NPT
Equipment Tray
Plate Hole
Set Screw
1-1/2” NPT
Step 1. Place the threaded end of the 1-1/2” NPT
Step 2. Use an M3 security wrench to tighten the
set screw.
into the plate hole.
Step 3. Attach projector mount to NPT.
The NPT must rotate onto the
equipment tray four (4) complete
rotations.
Please follow the instructions
included with the mount to complete
this step. If using a PDS Series mount,
connection may be made directly to
the bottom of the equipment tray.
Installation Instructions
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
PDS-PLUS Installation without NPT (Optional)
Before attaching the PDS-PLUS, it is strongly recommended that all connections in the equipment tray be made at this
time. Once the connections are made, feed the cables through the plate hole and then through the 1-1/2” NPT. Please read
instructions below to complete the installation.
Please refer to the PDS-PLUS Installation Instructions before proceeding with the following steps.
Mounting Slots
Equipment
Tray
M8 x 12mm
Security Head
Screw
M5 Security
Wrench
Base Box
Bridge
Step 1. Remove the lower mounting plate from
the equipment tray by removing the four
(4) M8 x 12mm security head screws with
an M5 security wrench.
Step 2. Locate the mounting slots that are on the
base box bridge of the PDS-PLUS.
Mounting
Point
Equipment
Tray
Equipment
Tray
Base Box
Bridge
Base Box
Bridge
M5 x 10mm
Security Head
Screw
M5 Security
Wrench
M5 Security
Wrench
M5 x 10mm
Security Head
Screw
Step 3. Line up the mounting slots on the base box
bridge with the mounting points on the
equipment tray.
Step 4. Insert four (4) M5 x 10mm security screws
and tighten using the M5 security wrench.
Be aware of the screen location and
orient the base accordingly.
Page 6
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
Cable Connections
Please refer to the PDS-PLUS Installation Instructions before proceeding with the following steps.
Equipment
Tray
PDS-PLUS
Base Box
Cables
Cables
Step 1. Pull all cables down through the
Step 2. Pull all cables down through the
PDS-PLUS projector plate.
PDS-PLUS base box.
Step 3. Attach all cables to the installed
projector.
Side Panel Installation
M4 x 8mm
Security Screw
Side Panel
Side Panel
M3 Security
Wrench
Side Panel
Step 2. Tighten these screws using the M5
Step 1. Attach the two side panels using eight (8)
security wrench.
M4 x 8mm security screws.
Installation Instructions
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
Lateral Shift Adjustment
M5 Security
Wrench
M8 x 12mm
Security Head
Screw
Step 1. Use the M5 security wrench and loosen
Step 2. Once the screws have been loosened,
slide the GB-PIPE1 laterally side to side
(or front to back).
Step 3. When the desired position has been
determined, use the M5 security wrench to
tighten the M8 x 12mm security screws.
the four (4) M8 x 12mm security screws.
Do not completely remove these screws.
Technical Specifications
All measurements are in inches(mm).
Page 8
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
GB-PIPE1
Warranty
PREMIER MOUNTS
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Premier Mounts warrants this product to be free from defects in material and workmanship for the lifetime of
the original owner of this product. The limited warranty is valid only for the original purchaser of the product.
What Premier Mounts Will Do
At the sole option of Premier Mounts, Premier Mounts will repair or replace any product or product part that is
defective. If Premier Mounts chooses to replace a defective product or part, a replacement product or part will
be shipped to you at no charge, but you must pay any labor costs.
What is Not Covered; Limitations
PREMIER MOUNTS DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DIS-
PLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN
PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
PREMIER MOUNTS DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. PREMIER
MOUNTS IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUD-
ING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOV-
ING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to
the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original con-
sumer purchaser must accompany all warranty claims. Warranty claims must also include a description of the
problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to Premier
Mounts Customer Service at 1-800-368-9700. Warranty claims will not be accepted over the phone or by fax.
Premier Mounts
Attn: Warranty Claim
3130 East Miraloma Ave.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER
RIGHTS WHICH VARY FROM STATE TO STATE.
Installation Instructions
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
|