POWERCLASS™
PC2400 / PC2600 / PC21400 OWNER’S MANUAL
CONTENTS
(click on a topic to view)
CONGRATULATIONS
INPUTS
FEATURES / SPECIFICATIONS
QBASS PLUS
CROSSOVER/GAIN CONTROL
THERMAL MANAGEMENT
TROUBLE SHOOTING
SYSTEM DIAGRAM ONE
SYSTEM DIAGRAM TWO
SYSTEM DIAGRAM THREE
SYSTEM DIAGRAM FOUR
BLOCK DIAGRAM
INSTALLATION
WIRING
WIRING (continued)
POWER / GROUND
POWER, GROUND, and REMOTE
REAR ENDPLATE DIAGRAM
FRONT ENDPLATE DIAGRAM
SPEAKER WIRING
ADDENDUM
WARRANTY
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES / SPECIFICATIONS
Adaptive MOSFET Switching Power Supply
Fully Complementary Triple Darlington Output Stage
AM IV Protection Circuitry
™
QBASS PLUS Bass Boost
™
QBASS REMOTE Compatible
Advanced Buss Technology
Forced Air Thermal Management
Two-Way 24dB/Octave Linkwitz-Riley 90Hz Crossover
Crossover Line Outputs
Balanced Differential Input Stage
High Voltage Input Capability with Input Attenuation Switch
Gold Plated RCA Input and Output Connectors
PowerLock Speaker and Power Wire Connectors
Mixed Mono/Stereo Operation
Three Year Warranty when installed by an Authorized PrecisionPower Dealer
Completely Designed and Handcrafted in the USA
Specifications
Power Bandwidth
Total Harmonic Distortion
Input Topology
4.5 Hz - 100 kHz
0.02 %
Differential
Input Sensitivity
150mv - 12 volts RMS
10 k Ohms
2 - 8 Ohms
4 - 8 Ohms
11 - 15 volts
Input Impedance
Load Impedance (stereo)
Load Impedance (bridged)
Supply Voltage
Damping Factor
>500
Slew Rate
>50 V/µS
QBASS PLUS™
Frequency Centers
Idle Current:
Up To +18dB Boost
30Hz, 36Hz, 44Hz and 60Hz
PC2400 1.5 Amps
PC2600 2 Amps
PC21400 3 Amps
Two Way, 24dB/Octave Linkwitz-Riley
90Hz
Crossover
Crossover Frequency
Continuous Output Power
PC2400
Dimensions
100 WRMS x 2 @ 4Ω per channel
200 WRMS x 2 @ 2Ω per channel
400 WRMS x 1 @ 4Ω bridged
PC2600
Length - 15.75"
Height - 2.25"
Width - 8.9"
150 WRMS x 2 @ 4Ω per channel
300 WRMS x 2 @ 2Ω per channel
600 WRMS x 1 @ 4Ω bridged
PC21400
Length - 17.75"
Height - 2.25"
Width - 8.9"
350 WRMS x 2 @ 4Ω per channel
700 WRMS x 2 @ 2Ω per channel
1400 WRMS x 1 @ 4Ω bridged
Length - 25.25"
Height - 2.25"
Width - 8.9"
1
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
QBASS PLUS™
QBASS PLUS™
On PC2400, PC2600 and PC21400 amplifiers, we've
taken bass control to a higher level with QBASS PLUS™.
The two QBASS switches (labeled 1 and 2) on the front
end of the amplifier allow you to select one of four
frequency centers - 30Hz, 36Hz, 44Hz and 60Hz. The Q
SELECT switch determines the width of boosted
frequencies. A 'Q' of 2 (switch out) will give you a wide
boost while a 'Q' of 4 will boost a narrow range of
frequencies (See chart below). On the rear end panel
you will find the QBASS™ level control and the plug-in for
an optional QBASS REMOTE™ dash mounted level
control. Adjust the level control clockwise for up to 18dB
of boost at your selected frequency and Q.
QBASS PLUS™
QBASS™ Settings
Q = 2
Q = 4
1
IN
IN
OUT
OUT
2
IN
OUT
IN
Freq.
30Hz
36Hz
44Hz
60Hz
+18dB
+12dB
+6dB
0dB
OUT
36Hz
44Hz
30Hz
60Hz
CAUTION: QBASS PLUS™ should only be used in systems with
strong subwoofers. 18dB is a lot of bass boost and could damage full
range speakers.
Optional QBASS REMOTE™
This boost control can be mounted in the
™
TE
REMO
dash and will supersede the boost
control on the endplate.
ASS
B
Q
Designed and handcrafted in the USA
Q
B
ASS
Optional QPORT™ expansion
™
module allows one boost control
to operate multiple amplifiers. Each
+18
QPORT™ has outputs for four amplifiers
as well as another QPORT™ for greater
expansion. See your Authorized PrecisionPower
Dealer for more information!
2
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
INSTALLATION
Tools/Parts needed for Installation (not supplied)
Small flat blade screwdriver
Phillips Screwdriver (#2 or medium sized)
Wire cutters
Wire strippers
4 - #6 round head screws, and 1 - #8 sheet metal screw
(or nut, bolt, and star washer)
2 - Ring connectors (large enough to accommodate your
method of grounding)
In-line fuse or circuit breaker - see fuse chart below
Power and ground wire - see Power Wire Calculator on page 3
Speaker wire - 16 gauge or larger
Grommets (sized to work with the power wire you plan to use
in your installation)
Tube of silicone sealant
Fuse requirements
Amplifier
PC2400
PC2600
PC21400
Maximum Fuse Rating
60 Amp
80 Amp
160 Amp
You will need to install an in-line fuse or circuit breaker in
the power wire within 18" of the battery. This fuse or circuit
breaker is to protect your vehicle from fire in case the power
wire shorts to the vehicle body. If you are only using one
amplifier, use the fuse rating indicated in this chart. If you are
using more than one amplifier, add up the fuse ratings for all the
amplifiers. This sum is the rating for your fuse or circuit breaker.
You may also want to add a power distribution block near your
amplifiers to keep the wiring tidy.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
WIRING
The following is a basic formula to be used as a guide to determine current
draw. A 50% amplifier efficiency rating is used as an average. Your new
™
POWERCLASS amplifier is more efficient, other amplifiers will probably
be less. This formula is to be used as a guideline. Using wire of a larger
gauge can only improve the current transfer of your system. Do not use
smaller gauge wire.
Total RMS output x 2 = Total Input Wattage
Total Input Wattage
= Current Draw (in Amps)
Supply Voltage
™
Example:A POWERCLASS 2600 amplifier has two channels at 150 watts
per channel RMS rating into 4 Ohms (150 x 2 = 300).You would use the
formula in the following way:
300W x 2 = 600W
600W
12V
= 50A Total current draw.
If the same amplifier is driven into a 2 Ohm stereo or 4 Ohm mono load,
™
double it's 4 Ohm RMS rating.All POWERCLASS amplifiers will effectively
double their power at this load.
300W x 2 x 2 = 1200W
1200W
12V
= 100A Total current draw.
If you are using more than one amplifier, add up the total current draw
for all of them and choose the appropriate gauge based on the grand total.
Power Wire Calculator
Recommended MINIMUM Gauge
Total Current Draw
Length Of Wire To Be Run
( in Amps)
Up to 4ft. 4 to 7ft. 7 to 10ft. 10 to 13ft. 13 to 16ft. 16 to 19ft. 19 to 22ft. 22 to 28ft.
0-20
20-35
35-50
50-65
65-85
85-105
105-125
125-150
14
12
10
8
6
6
12
10
8
8
6
6
4
2
12
8
8
6
4
4
4
2
10
8
6
4
4
2
2
2
10
6
6
4
2
2
2
0
8
6
4
4
2
2
0
0
8
6
4
4
2
2
0
0
8
4
4
2
0
0
0
00
4
2
(
NOTE: The ground wire should be the same gauge as the power wire.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
WIRING
Before beginning, disconnect the negative (-) terminal of the
battery prior to working on the positive (+) terminal to prevent
a short to ground. This is important, unless you want to spend
the rest of your life with a nickname like "Sparky," or "Smokey."
Reconnect the negative terminal only after all connections have
been made.
Warning!
Fuse must be installed within 18" of battery
5
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
POWER / GROUND
Grounding
Locate an area near the amplifier(s) that is metal and clean
an area about the size of a quarter to bare metal. Inspect the
area around and underneath to be sure you won't drill into wires,
brake or fuel lines, etc. Drill a pilot hole in the middle of this
area.Terminate the ground wire with a ring connector and attach
it to the bare metal using a #8 sheet metal screw and washer
or preferably, a bolt, nut and a star washer (not supplied). We
suggest crimping and soldering this connection. After the
connection is complete, coat the area (on both sides) with
silicone or some similar material to prevent rust from
developing on the bare metal.
If your grand total current draw is over 50 amps (or total output
power is over 300 watts), you should run a ground wire beside
your power wire from the battery to the amplifier(s) in addition
to your regular ground wire. Keep the ground and power wires
as close together as possible, and use the same gauge wire
for both. This will ensure that you have a good ground path,
and may eliminate such potential problems as engine noise
and overheated amplifiers.
Charging System Considerations
If your grand total current draw is over 100 amps (or total output
power is over 600 watts), you are probably exceeding the
capability of your charging system. Dimming lights and
fluctuating voltage are solid indicators that you need to upgrade
your alternator, battery (or go to multiple batteries), or both.
Keep in mind that your amplifiers simply convert electrical
energy to acoustical energy, and any electrical deficiency will
compromise the performance of your sound system.
For more information about charging system upgrades, see
your local authorized PrecisionPower Dealer or call the
PrecisionPower technical support office at 1-800-62POWER.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
POWER / GROUND and REMOTE
Once you have run both the power and ground wires, it's time
to connect the cables to the amplifier. Cut off excess wire and,
using wire strippers, strip the ends of the power and ground
cables approximately 1/4 inch. Locate the PowerLock power
and ground connector (supplied).With a small flat bladed screw
driver, loosen the screws before attempting to insert the cables.
Insert the wires into the appropriate hole, and tighten the
screws. Once the wires are secure, the PowerLock may be
plugged into the amplifier. The Power/Ground PowerLock will
accommodate 4 gauge wire for the PC2400, PC2600 and
PC21400.
Power/Ground PowerLock
Fastening screws
Power wires
Connect to Amplifier
7
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
ENDPLATE DIAGRAM
2400 / 2600 / 21400
1. QBASS REMOTE™ plug in
Plug in the data cable from the optional QBASS REMOTE™ dash mount level control here.
(This will bypass the amplifier's on board QBASS control)
2. COOLING VENTS (see page 13).
3. POWER / GROUND POWERLOCK
After you have securely connected your power and ground wires, plug in the
Power / Ground POWERLOCK connector here (see page 7).
4. POWER indicator
A green light indicates that the amplifier is on.
5. QBASS™ Level
Turn this control clockwise to boost the QBASS PLUS™ circuit by up to 18dB.
6. FORCED AIR INTAKE VENTS (see page 13).
1
4
2
3
POWER
Designed and Handcrafted in the U.S.A.
QBASS
0
+
18
QBASS
+
-
REMOTE
5
6
8
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
ENDPLATE DIAGRAM
2400 / 2600 / 21400
1. FRONT INPUTS
Plug in the RCA leads from your head unit here (see page 11).
2. GAIN
Use this control to match the output level of the head unit to the amplifier (see page 12).
3. HP/LP switch
This switch is used to select whether the amplifier will provide a high
pass (switch in) or low pass (switch out) signal to the speakers. (see page 12).
4. QBASS 1
Use this switch with the QBASS 2 to program the QBASS PLUS™ circuit. (see page 2).
5. QBASS 2
Use this switch with the QBASS 1 to program the QBASS PLUS™ circuit. (see page 2).
6. FORCED AIR EXHAUST VENTS (see page 13).
7. SPEAKER/REMOTE CONNECTOR
After connecting remote and speaker wires, plug in the PowerLock
connector here (see page 10).
1
2
3
4
5
6
7
QBASS
2
INPUTS
GAIN
OUTPUTS
L- L+ REM R+ R-
L
R
1
L
HP/LP
-12dB
Q SELECT
4/2
XOVER ON/OFF
R
8
10 11
12
9
8. -12dB
For use with high level inputs (4V up to 12V). Push this switch
in to attenuate the input by 12dB (see page 11).
9. XOVER ON/OFF switch
Push this switch in to activate the crossover, or out for full range speaker outputs (see page 12).
10. OUTPUTS
Left and Right RCA outputs provide high pass or low pass signal to another amplifier
(see page 12). NOTE - RCA outputs are always high pass or low pass.
11. Q SELECT 4/2
Push this button in for a Q setting of 4 and out for a setting of 2 (see page 2).
12. FORCED AIR INTAKE VENTS (see page 13).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
SPEAKER WIRING
Using 16 gauge or larger, run the speaker wires from the
amplifier location through the vehicle to the speakers.Observe
the same precautions for routing these wires that you followed
for running the power and remote turn-on wires.Cut off excess
and, using wire strippers, strip 1/4 inch of insulation. Locate
the speaker/remote turn-on PowerLock connector. Loosen
the four outer screws on the underside of the connector. Insert
the speaker leads into the end. Check to be sure you've
maintained proper polarity before securing each wire, and plug
the PowerLock into the amplifier.
Speaker PowerLock Connector
Right Speaker negative
Right Speaker positive
Remote turn on
Left Speaker positive
Left Speaker negative
Speaker/Remote PowerLock
Bridging
™
All two-channel POWERCLASS amplifiers are capable of being
bridged into a 4 ohm mono output without switches or bridging
modules. This feature permits the creation of a mono channel
for a subwoofer or center channel.
Deriving the mono channel is accomplished by using the left
channel positive wire as the positive speaker wire and the right
channel negative wire as the negative speaker wire.
NOTE: It is important that a minimum 4 ohm impedance is
observed. If the impedance drops below 4 ohms while the
amplifier is wired in the bridged configuration, the amplifier's
protection circuitry (AM IV) may engage.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
INPUTS
There are two sets of RCA jacks on the front end of your
amplifier. The RCA cables from your head unit go in the set
labeled INPUTS. If your head unit doesn't have RCA outputs
don't worry. Simply add a set of RCA plugs (available at your
dealer) to your front or rear set of speaker leads (see drawing
below), plug them into the input jacks, and push in the -12dB
input attenuation switch.
SOURCE Headunit
eject
1
5
2
6
3
7
4
8
Trk 1
BASS
TREBLE
PPI MAR KET ING DPT
BALANCE
TRACK
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
(+) Positive
LEFT input
(-) Negative
(+) Positive
RIGHT input
(-) Negative
WARNING: If you are using a source unit with bridged high powered (or
"floating ground") speaker outputs, a suitable high to low level adapter must be
used. If you are unsure about your head unit see your local PrecisionPower
dealer or call 1-800-62Power
Balanced Differential Inputs
This circuitry reduces noise radiated into your
signal cables by up to 40dB. This is equivalent to a noise
reduction of approximately one hundred times what the noise
level would be without this circuitry. It provides all the benefits
of a true 'balanced' line without the need of any special cables
(see diagram below). This type of input works with any
conventional RCA cable.
music
noise
(+)
(
+
=)
( )
signal and ground
music noise
music
and noise
music
noise
noise
(+)
( )
(
-
= 0 )
noise cancels
music
NO noise
11
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
CROSSOVER and GAIN CONTROL
Crossover
Your new POWERCLASS™ amplifier has a 90Hz fourth-order
Linkwitz-Riley type, 24dB per octave phase correlated
crossover built in to provide system flexibility without the added
expense and installation of an outboard crossover. The speaker
outputs of your amplifier are high pass or low pass according
to the HP/LP switch on the front endplate.
You would choose low pass (switch out) to use this amp for
subwoofers, or choose high pass (switch in) to use this amp
for full range speakers.The RCA outputs are controlled by the
same HP/LP switch, but are always the inverse of the speaker
output crossover. If the HP/LP switch is out (LP) the RCA
outputs will be high pass, and if the HP/LP switch is in (HP) the
RCA outputs will be low pass. In addition, the speaker outputs
can be all pass (no crossover) by setting the XOVER ON/OFF
switch to the off (out) position.
NOTE:The RCA outputs are always crossed over.The System
Diagrams beginning on page 14 show several ways to use the
internal crossover in your system.
Adjusting The Amplifier Input Gain
1. Adjust all amplifier input gain controls to just above minimum
sensitivity (fully counterclockwise).
2. Using the cleanest source (CD), with music playing turn up
the head unit until you can hear distortion. Now turn it down a
bit until you cannot hear the distortion.
3. Increase the Amplifier gain (clockwise) until the onset of
audible distortion. Then decrease the gain to the point just
before the distortion starts.This setting minimizes background
noise and prevents overload.
4. Repeat step 3 for any remaining amplifiers in the system.
12
Download from Www.Somanuals.com. All Manuals Search And DownloBadA.CK TO CONTENTS
THERMAL MANAGEMENT
Heatsink Cooling
The unique heatsink on
™
your POWERCLASS
amplifier has been
designed with fins on the
inside of the aluminum
mass. This allows for the
transfer of heat from the
circuitry to the heatsink fins and out through the vents in the
endplates.Be sure you have ample space around the amplifier
for cooling, at least 2" on all sides.
Forced Air Thermal Management
To manage the additional heat associated with higher output
capability, a thermally controlled fan has been designed into
the PC2600 and PC21400. When the heatsink temperature
reaches a pre-determined value, the fan is activated and
cool air is drawn in through the lower intake vents on the
endplate. This cool air flows below
the circuit board, through the fan
and across the internal fins,
cooling the heatsink. The
warm air is then forced
out through the upper
endplate exhaust
vents.
Cool Air Intake
Warm Air Exhaust
13
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
TROUBLE SHOOTING
NO SOUND
Is the LED lit?
YES
NO
Check Power and Remote turn-on wire
for voltage. Make sure Ground wire is
secure.
STILL NO SOUND - See your Authorized PrecisionPower Dealer or call
1-800-62POWER.
SOUND IN ONE CHANNEL ONLY
Reverse left and right speakers by unplugging the speaker connector, turning it
over and plugging it back in.
SOUND IS NOW IN
OPPOSITE CHANNEL
Reverse RCA inputs
SAME CHANNEL
Problem is in the speaker or speaker
wire of the silent channel.
SOUND IS NOW IN
SAME CHANNEL
OPPOSITE CHANNEL
Problem is in the Amplifier. See your
local Authorized PrecisionPower Dealer
or call 1-800-62POWER.
Reverse RCAs at head unit
SOUND IS NOW IN
OPPOSITE CHANNEL
Problem is in the head unit
SAME CHANNEL
Problem is in the RCA cables
AMPLIFIER TURNS DOWN
Both excessive temperature and low impedance (or short circuit)
conditions will activate the amplifier's AM IV protection circuitry, which
turns down the amplifier's output.When the amplifier cools down, or the
impedance is corrected, the AM IV will restore full power.
If your amp is turning down check your speakers and wiring for low
impedance and short circuits.Also,ensure that there is nothing blocking
the normal convective airflow of the amplifier. No obstruction should be
within 2" of the amplifier on all sides.
NOTE: Low battery voltage will cause the amplifier to run warmer.
Download from Www.Somanuals.co1m4. All Manuals Search And Download.
BACK TO CONTENTS
SYSTEM DIAGRAM
ONE
Source Unit
eject
1
2
3
4
5
6
7
8
Trk
1
BASS
TREBLE
BALANCE
TRACK
P
P
I
M
A
R
K
E
T
I
N
G
D
P
T
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
Passive
Crossover
Passive
Crossover
Tweeter
Tweeter
MidRange
MidRange
™
POWERCLASS Amplifier
Crossover Off
Passive
Crossover
Subwoofer
Mixed Mono Output
The ability to run stereo speakers while simultaneously running a
mono output from the same amplifier is accomplished by running the
stereo speakers normally and tapping into the appropriate wires for
the "mixed mono" channel (left channel positive for the positive
speaker wire and right channel negative for the negative speaker
wire). Speaker impedance should be no lower than 2 Ohms on the
stereo channels and 4 ohms on the mono channel.
NOTE: Passive crossovers must be used for "mixed mono" operation.
Choose a low pass crossover around 100Hz for your subwoofer, then
choose a high pass crossover for your stereo channels. The high
pass crossover must be at the same or slightly higher frequency than
the low pass crossover to maintain the correct impedance. See your
PrecisionPower dealer or call 1-800-62POWER for more information
about passive crossovers.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
SYSTEM DIAGRAM
TWO
Source Unit
eject
1
2
3
4
5
6
7
8
Trk
1
BASS
TREBLE
BALANCE
TRACK
P
P
I
M
A
R
K
E
T
I
N
G
D
P
T
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
Passive
Crossover
Passive
Crossover
Tweeter
Tweeter
MidRange
MidRange
™
POWERCLASS Amplifier
High Pass 90Hz
Low Pass Out to Sub Amplifier
Subwoofer
Subwoofer
™
POWERCLASS Amplifier
Crossover off or Low Pass
16
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
SYSTEM DIAGRAM
THREE
Source Unit
eject
1
2
3
4
5
6
7
8
Trk
1
BASS
TREBLE
BALANCE
TRACK
P
P
I
M
A
R
K
E
T
I
N
G
D
P
T
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
R
In
pu
t
L
In
R
pu
R
pu
t
O
ea
t
r
S
ut
en
si
ti
L
vi
ty
R
Fr
ont
pu
O
ut
t
L
LE
D
S
el
ec
t
1
P
ow
er
2
Fr
e
q
3
ue
n
c
4
y
P
A
d
ju
st
re
c
is
io
P
A
Su
b
V
n
P
ow
o
lu
R
-
m
e
2
4
e
r
Lo
w
5
Po
w
Low
er
-M
id
F
In
H
-
R
igh
-M
i
id
Tr
eb
le
+
M
d
ad
e
in
er
+
D
U
S
ef
ea
A
t
+
+
w
+
id
M
id
l
e
P
A
R
-2
45
PAR-245 Preamp/Equalizer
Front Output
Rear Output
l
tro
on
C
h
ift
A
S
S
U
se
ha
in
e
ad
P
M
0
0
60
22
0
o
10
se
P
ha
-ø
t
R
i
gh
r
e
w
r
e
o
P
w
o
P
n
io
is
c
1
0
60
re
22
0
P
-
22
0
C
S
P
o
10
e
as
P
h
-ø
ft
Le
s
s
a
In
r
e
P
p
y
u
t
w
o
B
r
t
L
P
n
L
e
v
io
I
n
s
s
is
c
re
L
a
P
y
P
B
rt
R
ve
In
R
in
R
•
d
N
t
n
o
n
-in
u
te
u
o
o
ve
r
•
r
In
r
G
m
v
e
d
e
e
rt
/
A
R
w
ed
o
c
/
B
ti
P
e
yP
a
ss
PSC-221 Phase Shift Control
Passive
Crossover
Passive
Crossover
Tweeter
Tweeter
MidRange
MidRange
™
POWERCLASS Amplifier
High Pass at 90 Hz
Subwoofer
Subwoofer
™
POWERCLASS Amplifier
Low Pass at 90 Hz
17
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
SYSTEM DIAGRAM
FOUR
Source Unit
eject
1
2
3
4
5
6
7
8
Trk 1
BASS
TREBLE
BALANCE
TRACK
P
P
I
M
A
R
K
E
T
I
N
G
D
P
T
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
R
In
pu
t
L
R
R
ut
pu
In
pu
ea
r
t
t
O
S
en
si
ti
vi
L
ty
R
Fr
ut
pu
O
ont
t
L
LE
D
S
el
ec
t
1
P
ow
er
2
Fr
e
q
ue
3
n
c
4
y
P
A
d
ju
re
c
st
is
P
A
io
Su
b
V
n
o
P
ow
lu
R
-
m
e
2
4
e
r
Lo
w
5
Po
Low
-M
id
F
In
H
igh
-C
R
l
-M
id
Tr
eb
le
+
a
M
d
ad
e
in
er
+
D
U
S
f
ea
A
t
+
b
+
w
+
M
id
-
M
id
r
l
e
P
A
R
-2
45
Hz
7K
3.3
z-2
KH
14
H
Hz
5K
5.7
-1
Hz
7K
9.3
L
Q
H
z
KH
4
.37
-9
PAR-245 Preamp/Equalizer
4K
Hz
L
t
os
Bo
Q
.
1
H
ut
/
C
hz
.5K
z-4
KH
4
db
L
+
1
2
5
1.9
Q
.
st
oo
A
S
1
b
H
t
/
B
-
1
2
d
in
e
ad
U
Cu
Hz
5K
4
.2
-1
1
2
db
M
0
94
Hz
L
+
a
liz
e
r
Q
.
5
t
q
u
1
os
Bo
E
H
/
db
ric
et
m
ara
-
1
2
z
4
C
ut
KH
z-1
0H
33
b
L
+
1
2
d
d
an
P
Q
.
5
B
1
st
oo
H
1
0
t
Cu
/
B
1
Hz
50
4
z-5
0H
16
+
1
2
db
Q
.
5
1
t
os
H
/
B
o
-
1
2
Hz
60
-2
Hz
80
4
t
Cu
L
2
db
+
1
Q
.
5
1
H
ost
Hz
/
B
o
-
1
2
db
30
4
C
ut
-1
Hz
40
1
2
d
b
Q
.
5
+
1
H
s
t
oo
Hz
4
/
B
-
1
2
db
z-
2
70
C
ut
0H
d
b
Q
5
+
1
2
H
st
oo
4
/
B
-
1
2
db
C
ut
b
Q
2
d
+
1
e
r
1
ow
st
oo
r
P
e
4
/
B
w
o
C
ut
P
n
io
1
2
d
b
is
0
1
5
+
c
e
r
-2
t
os
P
Q
/
Bo
M
ut
1
P
C
d
b
+
1
2
EQ
-
1
2
d
at
fe
De
r
e
w
o
P
n
io
is
c
re
P
In
p
u
a
tt
t
e
O
u
n
u
a
t
p
tio
n
u
t
-1
2
st
e
re
d
B
in
o
•
o
u
n
m
t
o
no
•
L
i
R
L
R
d
n
u
te
o
o
r
G
m
r
e
e
R
w
o
P
PMQ-210 Ten Band Parametric EQ
r
ve
so
os
Cr
SA
n
tro
ic
in
e
ad
U
c
E
l
e
M
a
y
W
ix
/S
ive
/F
o
ur
F
+
_
2
3
44
7
5
l
v
e
L
e
F
i
l
l
R
e
a
r
1
5
2
4
1
92
3
4
7
.
4
K
80
t
e
r
e
e
T
w
1
1
2
44
7
5
2
1
.
7
7
K
3
80
n
g
R
a
e
5
2
R
e
a
r
l
tro
on
1
4
4
K
i
d
M
1
92
3
4
7
.
C
8
0
e
r
ift
A
S
e
t
h
S
1
1
2
T
w
e
U
1
72
2
7
2
7
7
K
1
.
se
ha
e
ad
M
in
P
8
0
ge
92
R
a
n
70
6
1
1
8
2
49
M
i
d
r
e
w
5
6
s
n
t
o
3
B
a
s
F
r
o
P
4
0
60
n
16
10
2
5
26
M
i
d
o
0
22
i
si
c
6
2
2
re
45
P
-
P
a
s
s
X
+
o
w
0
10
o
R
4
6
L
F
7
_
i
c
se
P
ha
+
1
0
b
S
o
n
t
S
u
-ø
i
gh
R
e
r
r
e
∞
G
a
i
n
o
o
f
r
s
s
S
u
b
w
e
w
o
P
a
w
o
P
e
r
o
w
L
w
P
n
Po
io
is
In
c
1
0
60
L
p
L
re
22
0
u
P
-
C
22
ts
S
P
o
0
10
r
e
w
e
as
o
c
n
io
P
-ø
ft
Le
P
h
o
m
b
in
is
e
c
in
d
R
re
P
p
u
ts
•
in
R
s
s
d
a
In
r
e
n
P
u
e
y
p
u
t
r
o
o
t
B
t
w
o
re
G
m
r
e
r
L
P
n
a
e
e
L
v
r
R
w
n
s
io
o
I
s
is
c
re
P
L
a
P
fr
y
P
o
B
n
rt
R
ve
In
R
in
R
•
d
N
t
n
o
on
-in
u
te
u
o
o
ve
r
•
r
In
rt
e
G
m
v
e
d
e
e
rt
/
A
R
w
ed
o
c
/
B
ti
P
ve
yP
a
ss
FRX-456 Crossover
PSC-221 Phase Shift Control
High Pass Frequencies
Tweeter
Mid Range
Subwoofer
Tweeter
™
POWERCLASS Amplifier
Crossover off
Mid Range Frequencies
Mid Range
™
POWERCLASS Amplifier
Crossover off
Low Pass Frequencies
Subwoofer
™
POWERCLASS Amplifier
Crossover off
18
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
BLOCK DIAGRAM
BSA
PULS
Q
BSARMOTE
Q
- 12dB INPUT ATTENUATION
19
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
POWERCLASS ADDENDUM
DETENT
XOVER FREQ
™
1
20 Hz
Your new POWERCLASS amplifier
may have been updated to include a
variable detented crossover in place
of the Q 4/2 function switch. The
crossover is adjustable from 20 Hz
to 5 kHz. Please refer to the
2
21 Hz
3
21 Hz
4
21.5 Hz
22 Hz
5
6
23 Hz
7
24.5 Hz
26 Hz
8
9
27.5 Hz
30 Hz
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
32 Hz
endplate diagram and detent chart
provided for frequency adjustments.
The XOVER FREQ control has
detents, or “clicks” as you rotate it.
Each "click" counted from the full
counterclockwise position
35 Hz
39 Hz
43 Hz
49 Hz
56 Hz
64 Hz
73 Hz
80 Hz
88 Hz
100 Hz
114 Hz
134 Hz
160 Hz
196 Hz
260 Hz
320 Hz
368 Hz
432 Hz
496 Hz
608 Hz
752 Hz
864 Hz
1008 Hz
1200 Hz
1488 Hz
1952 Hz
2816 Hz
4512 Hz
4944 Hz
5000 Hz
corresponds to a specific frequency.
This will add more accurate tuning
to your system.
Also, refer to your owner’s manual
for installation instructions.
As always, PrecisionPower will
continue to improve the products
and services we have to offer you.
Thank you for choosing
PrecisionPower!
New variable crossover
QBASS
2
INPUTS
GAIN
OUTPUTS
L- L+ REM R+ R-
L
R
1
L
HP/LP
-12dB
XOVER
FREQ.
XOVER ON/OFF
R
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
WARRANTY
Three-Year Limited U.S.A. Warranty
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state. PrecisionPower warrants its products to be free from defects in materials and
workmanship under normal use and service for a period of three (3) years from the date of
original purchase when the unit is installed by an Authorized Dealer. Non-Authorized Dealer
installed products carry a one (1) year parts and ninety (90) days labor limited warranty. The
extent and conditions of Limited Warranty are as follows:
1. Authorized Dealer Installed Products:PrecisionPower will either repair or replace at no charge,
to the original purchaser, any unit which PrecisionPower’s examination discloses to be defective
and under warranty, provided the defect occurs within three (3) years from the date of original
purchase when the unit is installed by an Authorized Dealer and the product is returned immedi-
ately to PrecisionPower. This warranty is not transferable.
2. Non-Authorized Dealer Installed Products: PrecisionPower will either repair or replace at no
charge, to the original purchaser, any unit which PrecisionPower’s examination discloses to be
defective and under warranty, provided the defect occurs within ninety (90) days from the date of
purchase and the product is returned immediately to PrecisionPower. Warranty claims beyond
ninety (90) days for Non-Authorized Dealer Installed Products will be for parts only and will
extend for one (1) year from the date of purchase. This warranty is not transferable.
3. The date of purchase and proof of Authorized Dealer Installation of a PrecisionPower product
must be established by an original sales receipt which must accompany the article being re-
turned for warranty work.
4. This warranty shall NOT apply to any PrecisionPower product found to have the original fac-
tory serial number removed or defaced. All products received (by PrecisionPower) for in war-
ranty or out of warranty repair, with their original serial numbers removed or defaced, will NOT be
repaired and will be returned to sender, freight collect. Refer to original packaging for the serial
number of your component speakers.
5. The provisions of this warranty shall not apply to any PrecisionPower product used for a
purpose for which it is not designed, which has been repaired or altered in any way, or which has
been connected, installed, or adjusted other than in accordance with the instructions furnished in
PrecisionPower’s owner’s manual. Nor shall this warranty apply to any part which has been
subject to misuse, neglect, or accident.
6. PrecisionPower does not authorize any other persons to assume any other liability in connec-
tion with its products. THIS WARRANTY IS THE ONLY EXPRESS WARRANTY MADE BY
PRECISIONPOWER APPLICABLE TO ITS PRODUCTS. ANY IMPLIED WARRANTY OR MER-
CHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE APPLICABLE TO
PRECISIONPOWER PRODUCTS IS LIMITED IN DURATION TO THE DURATION OF THIS
LIMITED WARRANTY. PRECISIONPOWER SHALL NOT BE LIABLE FOR THE INCIDENTAL,
CONSEQUENTIAL, OR COMMERCIAL DAMAGES RESULTING FROM THE BREACH OF THIS
WRITTEN WARRANTY. Some states or provinces do not allow the exclusion or limitation of
incidental or consequential damages or limitations on how long an implied warranty lasts; so the
above limitations or exclusions may not apply to you.
7.Your product will be serviced on an in-warranty basis within the warranty period for the correc-
tion of warranted defects. If improper operation of your PrecisionPower product should occur,
contact your Authorized Dealer for assistance with the return and factory repair of your
PrecisionPower
product. If an Authorized Dealer is not available, return the unit including your name, telephone
number, return address, a copy of your sales receipt, and a description of the problem to:
PrecisionPower,Inc.
Service Department
4829 S. 38th Street
Phoenix, AZ 85040-2964
TO RETURN PRECISIONPOWER PRODUCTS OUT OF WARRANTY: Return the unit, postage
prepaid, in the original protective carton. Please include a description of the problem and, if
desired, a request for an estimate of repair costs. Unless a request for an estimate is included,
the unit will be repaired as necessary. Please contact PrecisionPower Customer Service at 1-
800-62-POWER for questions concerning out of warranty repair charges. Repaired unit will be
returned with an itemized statement, C.O.D.
Download from Www.Somanuals.com. All Manuals Search And Download.
BACK TO CONTENTS
|