AMPLIFIER MODELS
A500/2
A800/2
A1000/2
Download from Www.Somanuals.com. All Manuals Search And Download.
CONGRATULATIONS
TM
Thank you for choosing Precision Power audio equipment.
Designed and engineered in the USA, this product combines
innovative technology with the finest materials to consistently deliver
Absolutely State of the Art™ performance, sound quality, reliability,
TM
and value. This Precision Power product reflects our commitment
to offer you unparalleled performance and quality for years of
dependable service and listening enjoyment.
SERVICE
TM
Do not attempt to service Precision Power products yourself.
Performing maintenance on your audio equipment will void the
TM
warranty. Many parts of the Precision Power product are custom
built to our specifications. Our factory parts are not made
available to anyone else nor are they for sale. Our goal is to
TM
make sure that your Precision Power product will always sound as
good as the day it was purchased. Contact your Authorized
TM
Precision Power Dealer about obtaining any warranty service
TM
through Precision Power . (See the Warranty on the outside of the
back cover).
CAUTION
Extended use of a high powered audio system may result in hearing
TM
loss or damage. While Precision Power systems are capable of
“Concert Level” volumes with incredible accuracy, they are also
designed for you to enjoy at more reasonable levels all of the sonic
subtleties created by musicians. Please observe all local sound
ordinances.
FEATURES
Advanced Instrumentation Input Stage.
24dB/Octave; HP/LP/FULL; 30-4kHz Crossover.
Independent Line Output Crossover 30-4kHz
PWM Power Supply
Triple Darlington Output Stage.
AP-IV Protection Circuity
TM
QBASS Bass Boost
2
Download from Www.Somanuals.com. All Manuals Search And Download.
High Voltage Input Capability with -12dB Attenuation Switch.
Gold Plated RCA Input and Output Connectors.
TM
PowerLock Speaker and Power Wire Connectors.
WHAT’S INCLUDED
Amplifier (with speaker and power plugs mounted)
(4) Mounting screws and washers
2mm hex wrench
2.5mm hex wrench
3mm hex wrench
CEA SPECIFICATIONS
A500/2
Power Output: 80 Watts RMS x 2 at 4 ohms and < 1% THD+N
Signal to Noise Ratio: -70 dBA (reference 1 Watt into 4 ohms)
Additional Power Output: 125 Watts RMS x 2 at 2 ohm at 14.4 Supply<1% THD+N
A800/2
Power Output: 125 Watts RMS x 2 at 4 ohms and < 1% THD+N
Signal to Noise Ratio: -88 dBA (reference 1 Watt into 4 ohms)
Additional Power Output: 220 Watts RMS x 2 at 2 ohm at 14.4 Supply<1% THD+N
A1000/2
Power Output: 230 Watts RMS x 2 at 4 ohms and < 1% THD+N
Signal to Noise Ratio: -92 dBA (reference 1 Watt into 4 ohms)
Additional Power Output: 325 Watts RMS x 2 at 2 ohm at 14.4 Supply<1% THD+N
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Nominal Power Ratings
MODEL
A500/2
A800/2
A1000/2
4 ohm
2 X 75
2 X 125
2 X 175
2 ohm
4 ohm MONO
1 X 250
1 X 400
2 X 125
2 X 200
2 X 250
1 X 500
General Specifications
Load Impedance (Stereo)
Load Impedance (Bridged)
Input Topology
Conversion Efficiency
Frequency Response
Linear Bandwidth
Input Sensitivity
2–8 ohms
4–8 ohms
Balanced differential
>50% @2 ohms max power
20Hz–200Hz 0.25dB
10–50kHz 3dB
150mv - 12 Volts RMS
HP/LP/Full; 30Hz to 4kHz
20,000 Ohms
RCA Output Jacks
Input Impedance
Supply Voltage
9–16 Volts
Damping Factor
>250 (A500/2), >1000 (A800/2),
>350 (A1000/2)
Slew Rate
>20V/µs
Crossovers Type/Range
HP—off/12dB switch 30Hz to 4kHz
LP—off/12dB switch 30Hz to 4kHz
12dB/octave
Crossover Slope
QBass (n/a to A500/2)
Variable 0 to +12dB boost @ 40Hz
QBassPlusTM remote (A500/2) Variable 0 to +18dB boost
(option)
Variable frequency (30Hz, 36Hz, 44Hz, 60Hz)
Protection Functions
Short and thermal
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Fuse Requirements
You will need to install an in-line fuse or circuit breaker in the power
wire within 18” of the battery.This fuse or circuit breaker is to protect
your vehicle from fire in case the power wire shorts to the vehicle
body. If you are only using one amplifier, use the fuse rating
indicated in this chart. If you are using more than one amplifier, add
up the fuse ratings for all the amplifiers. This sum is the rating for
your fuse or circuit breaker. You may also want to add a power
distribution block near your amplifiers to distribute large gauge
power cable to multiple amplifiers.
Amp
Fuse
25 A
35 A
50 A
A500/2
A800/2
A1000/2
Dimensions
Length
Width
Height
A500/2
A800/2
A1000/2
12-½”
24-¾”
27-3/8”
10-½”
2-¾”
10-½”
10-½”
2-¾”
2-¾”
5
Download from Www.Somanuals.com. All Manuals Search And Download.
AMPLIFIER STATUS LEDS
1
2
The LEDs provide the following indications:
1. Power - These LEDs illuminates the center Precision Power logo
background when the amplifier power is turned on.
2. Short - These LEDs behind the PPI logo will flash to indicate a
short on the output.
2. Thermal - These LEDs behind the PPI logo will extinguish if the
amplifier is in thermal shutdown protection.
Note: Read the AP-IV Protection Circuit section for additional
information regarding Short and Thermal protection.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
TOOLS/PARTS FOR INSTALLATION
NOTE:TOOLS ARE NOT SUPPLIED.
Small flat blade screwdriver
Phillips screwdriver (#2 or medium sized)
Wire cutters
Wire strippers
4 - #6 round head screws, and 1 - #8 sheet metal screw. (or nut, bolt,
flat washer, star washer) (see details)
2 - Ring connectors (large enough to accommodate your method of
grounding)
In-line fuse or circuit breaker
Power and ground wire
Speaker wire - 12-16 gauge
Grommets (sized to work with the power wire you plan to use in your
installation)
Tube of silicone sealant
WIRING
Before beginning, disconnect the negative (-) terminal of the battery
prior to connecting the amplifier to the positive (+) 12V terminal to
prevent a short to ground and potential damage to wiring and
equipment. Some vehicle radios have an anti-theft feature where
when the radio is removed from 12V the radio will no longer function
and must be code reset.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The cables running from the battery to the rear of the car
should be installed on the side of the car opposite to the antenna.
When using 16 gauge wire or larger, run the speaker wires from the
amplifier location through the vehicle to the speakers. Observe the
same precautions for routing these wires that you followed for running
the power and remote turn on wires. Cut off excess and, using wire
strippers, strip 1/4-inch of insulation. Locate the speaker/remote turn-
on PowerLockTM connector. Using a hex wrench loosen the screws on
the upperside of the connector. Insert the speaker leads into the end
and secure with the hex wrench. Check to be sure you've maintained
proper polarity before securing each wire.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The amplifier comes with the connector inserted into the
amplifier with the wire clamping screws in the up position as
shown below. Use a 2mm hex head wrench to secure the wires
to the connector. If the connector needs to be unplugged from
the amplifier, use a 2.5mm hex head wrench to remove the
retaining screw from the connector (set aside and save the
retaining screw).The two negative outputs are common to each
other as are the two positive outputs. A speaker may be
connected to either terminal.
Speaker
TM
POWERLOCK
Connector
2mm hex
wrench
Left Speaker -
Left Speaker +
Remote turn on
Right Speaker +
Right Speaker -
Remove retaining
screw with a
2.5mm hex wrench
GROUND WIRING
Locate an area near the amplifier(s) that is metal and clean an area
about the size of a quarter down to bare metal. Inspect the area
around and underneath to be sure you will not drill into wires, brake
or fuel lines, etc. Drill a pilot hole in the middle of this area.Terminate
the ground wire with a ring connector and attach it to the bare metal
using a #8 sheet metal screw and washer or preferable, a bolt, nut
and a star washer. (not supplied). We suggest crimping and
soldering this connection. After the
connection is complete, coat the area
(on both sides) with silicone or some
similar material to prevent rust from
developing on the bare metal. If your total current draw is over 80
amps (or total power is over 500 watts). Keep the ground and power
9
Download from Www.Somanuals.com. All Manuals Search And Download.
wires as close together as possible, and use the same gauge wire
for both.This will ensure that you have a good ground path, and may
eliminate such potential problems as engine noise and overheated
amplifiers.
CHARGING SYSTEM
If your total current draw is over 100 amps (or total output power is
over 600 watts), you are probably exceeding the capability of your
charging system. Dimming lights and fluctuating voltage are solid
indicators that you need to upgrade your alternator, battery, or both.
You should also check the condition and current capacity of the
stock battery negative cable and connections, and replace or
upgrade as necessary. Keep in mind that your amplifiers simply
convert electrical energy to acoustical energy, and any electrical
deficiency will compromise the performance of your sound system.
For more information about charging system upgrades, see you
TM
TM
local authorized Precision Power Dealer or call Precision Power
Technical Support at 1-800-62POWER x2033.
CURRENT DRAW
The following is a basic formula to be used as a guide to determine
current draw. Your new PPI amplifier is more efficient than most
other amplifiers.This formula is to be used as a guideline. Using wire
of a larger gauge can only improve the current transfer of your
system. Do NOT use smaller wire gauge.
Total RMS output X 1.5 = Total Input Wattage
Total Input Wattage
= Current Draw (in Amps)
Supply Voltage
Example: A PPI amplifier has two channels at 125 watts per
channel RMS rating into 4 ohms (125X2 = 250 watts).
You would use the formula in the following way:
250 W X 1.5 = 375 watts
10
Download from Www.Somanuals.com. All Manuals Search And Download.
375W
12V
= 31.25 Amps total current draw
If the same amplifier is driven into a 2 ohm stereo or 4 ohm mono
load, double it’s 4 ohm RMS rating. These amplifiers will effectively
double their power at this load.
250W X 1.5 X2 = 750 watts
750W
12V
= 62.5 Amps total current draw
If you are using more than one amplifier, add up the total current
draw for all of them and choose the appropriate gauge based on the
grand total.
POWER WIRE SIZE
A minimum of 8 gauge or a maximum of 4 gauge wire is
recommended dependent on the application.
The ground wire must be the same gauge as the power wire.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
POWERLOCK CONNECTORS
Once you have run both the power and ground wires, then connect
the cables to the amplifier. Cut off excess wire, and using wire
strippers, strip the ends of the power and ground cables
TM
approximately 1/4 inch. Locate the PowerLock power and ground
connector (supplied). Using a hex wrench, loosen the screws before
attempting to insert the cable wires. Insert the wires into the
appropriate hole, and tighten the screws. The Power/Ground
TM
PowerLock will accommodate 4 gauge wire for these amplifiers.
Note: The amplifier comes with the connector inserted into the
amplifier with the wire clamping screws in the up position as
shown below. Use a 3mm hex head wrench to secure the wires
to the connector. If the connector needs to be unplugged from
the amplifier, use a 2.5mm hex head wrench to remove the two
retaining screws from the connector (set aside and save the
retaining screws).
3mm hex
wrench
Power wires
Remove retaining
screw with a 2.5mm hex
wrench
Connection to
amplifier
12
Download from Www.Somanuals.com. All Manuals Search And Download.
FRONT PLATE DIAGRAM
12
11
R
R
L
BRIDGE
-
+
R- R+ REM L+ L-
OUTPUT XOVER
XOVER
LP
INTPUT FREQ FULL HP
GAIN
FREQ QBASS ATT
LP
30 40k
30 40k
L
MIN MAX
2
1
-12dB
OUTPUT FREQ FULL HP
1
2
3
4
5
6
7
8
9
10
1. Cooling Plenums: Maintain a minimum 2” clearance around
cooling plenums for proper amplifier cooling.
2. Speaker/Remote Connector: The PowerLockTM speaker
connector.
3. Output Xover Freq. Control: Use this control to adjust the sub
bass output signal crossover frequency from 30Hz to 4kHz. (See the
Crossover Frequency chart in this manual).
4. Output Xover FULL/LP/HP Switch: Select the desired crossover
setting HP/LP/FULL for the signal of the RCA outputs.
TM
TM
5. QBASS Freq.: Use this switch to set the QBASS frequency
(applicable to model A800/2 and A1000/2, refer to QBass
Plus/QBass Remote section).
6.-12dB Input Attenuation: Push this switch ‘IN’ for high voltage
(4V-12V) capability. This button pushed ‘IN’ must be used for
speaker level input on common ground head-units or for high
voltage line drivers.
7. Gain: Use this control to match the output level of the source unit
to the amplifier.
8. Input: Plug in the RCA leads from your source here.
9. Xover Adjustment: Adjusts the crossover between 30Hz and 4kHz.
10. Xover FULL/LP/HP Switch: Select the desired crossover
setting FULL/LP/HP.
TM
11. QBass: Use this switch to set the QBASS frequency
(applicable to model A800/2 and A1000/2). On the A500/2 this is the
13
Download from Www.Somanuals.com. All Manuals Search And Download.
QBass frequency control adjustment.
12. RCA Outputs: RCA outputs provide HP/LP/FULL 30-4kHz
signal to another amplifier.
END PLATE DIAGRAM
+18
0
QBASS
REMOTE
QBASS
1
2
3
4
1. Cooling Plenums: Maintain a minimum 2” clearance around
cooling plenums for proper amplifier cooling.
TM
2. Power/Ground PowerLock : Connect your power and ground
TM
to this Power/Ground PowerLock connector.
Note: Item descriptions 3 and 4 only apply to the A800/2
and A100/2 amplifiers.
TM
3. QBASS REMOTE : Plug in the data cable from the optional
TM
QBASS REMOTE dash mounted level control here. (The remote
TM
level control will bypass the amplifier’s on board QBASS control.
TM
4. QBASS Level Control: Controls bass boost, centered at 40Hz
with up to 18dB of boost. On the A500/2 this adjustment is on the
control panel (see previous figure).
14
Download from Www.Somanuals.com. All Manuals Search And Download.
INPUTS
There are two sets of RCA jacks on the front end of your amplifier.
The RCA cables from your source unit go in the set labeled
INPUTS. If your source unit doesn’t have RCA outputs, then add a
set of RCA plugs (available at your dealer) to your front or rear set
of speaker leads (see drawing below). Plug them into the input
jacks, and push in the -12dB input attenuation switch.
SOURCE Headunit
eject
1
5
2
6
3
7
4
8
Trk 1
BASS
TREBLE
PPI MAR KET ING DPT
BALANCE
TRACK
VOLUME
LEFT
RIGHT
FOWARD
REVERSE
(+) Positive
LEFT input
(-) Negative
(+) Positive
RIGHT input
(-) Negative
ADVANCED INSTRUMENTATION INPUT
The Advanced Instrumentation Input has been incorporated from
TM
the legendary Precision Power 2500F1. This circuit completely
isolates the chassis ground from the audio circuit of the amplifier
and reduces noise radiated into your signal cables by up to 40dB.
This is equivalent to a noise reduction of approximately one hundred
times what the noise level would be without this circuitry. It provides
all the benefits of a true balanced line without the need of any
special cables (see diagram below). This type of input works with
any conventional RCA cables.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
QBASS PLUS SPECIFICATIONS
Note: Not available on the model A500/2 amplifier.
TM
QBASS PLUS
Up to 18dB of boost with selectable center frequency at 30Hz, 36Hz,
44Hz or 60Hz, with a Q-factor of 2.
TM
Optional QBASS REMOTE
This boost control can be mounted in the dash and will supersede
the boost control on the amplifier endplate.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
QBASS PLUS/QBASS REMOTE
On A800/2, and A1000/2 amplifiers, we’ve taken bass control to a
TM
TM
higher level with QBASS PLUS . The two QBASS switches
(labeled 1 and 2) on the front end of the amplifier allow you to select
one of four frequency centers 30Hz, 36Hz, 44Hz and 60Hz. On the
TM
rear end plate you will find the QBASS level control and plug-in for
TM
an optional QBASS REMOTE dash mounted level control. Adjust
the level control clockwise for up to +18dB of boost at your selected
frequency.
TM
QBASS Settings
1
2
Freq.
30Hz
36Hz
44Hz
60Hz
IN
IN
IN
OUT
IN
OUT
OUT
OUT
TM
CAUTION: QBASS PLUS should only be used in systems with a
strong subwoofer section. +18dB is a tremendous amount of bass
boost and may damage your speakers or create excessive distortion
if abused.
TM
The optional QBASS REMOTE : This boost control can be
mounted in the dash and will supersede the boost control on the
endplate.
These Precision Power amplifiers no longer need an optional
TM
TM
QPORT to connect multiple QBASS PLUS equipped amplifiers
TM
TM
while using one QBASS REMOTE . The new QBASS PLUS
circuitry in the A800/2 and A1000/2 amplifiers is now positioned
TM
before the crossover circuit. In doing this, Precision Power
engineers have allowed you to daisy chain your RCA output to the
TM
next amplifier input, causing the first amplifier’s QBASS REMOTE
to become the master control amplifier. See your authorized
TM
Precision Power dealer for more information!
17
Download from Www.Somanuals.com. All Manuals Search And Download.
TC-X CROSSOVER
Your new amplifier has a TC-X Crossover (Total Control X-over®)
30Hz-4kHz (see this guide for Crossover Chart).12dB per octave
phase correlated crossover built-in to provide superior system
flexibility without the added expense and installation of an outboard
crossover. The speaker outputs of your amplifier are high pass, low
pass, or all-pass according to the HP/LP/FULL switch on the front
endplate. You would choose low pass (middle position of switch) to
use this amplifier for subwoofers, choose high pass (left position of
switch), or full (right position of switch) to use this amplifier for full
range speakers.
The RCA outputs are controlled by a separate HP/LP/FULL switch,
and are always independent of the speaker output crossover. As
well as being able to independently select HP/LP/FULL, your new
DCX amplifier allows independent selection of frequencies from
30Hz-4kHz (see Crossover Detent Chart in this guide).
A500/2, A800/2, A1000/2
Speaker Output - 12dB/Octave, Detented HP/LP 30Hz-4kHz
Low Level Output - 12dB/Octave, Detented; HP/LP
TM
QBASS PLUS - up to 18dB @ 30, 36, 44, 60Hz (A800/2 and
A1000.2, only)
18
Download from Www.Somanuals.com. All Manuals Search And Download.
CROSSOVER DETENT CHART
Low Pass
Frequency (Hz)
@ -3dB
28
High Pass
Frequency (Hz)
@ -3dB
52
Detent #
1
2
28
52
3
30
52
4
30
56
5
30
56
6
32
60
7
34
64
8
36
72
9
38
76
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
46
50
52
54
60
66
76
80
88
92
100
116
132
148
168
192
216
244
284
348
404
468
512
88
100
116
136
144
168
198
240
286
310
340
380
424
484
576
632
748
932
1076
1428
1700
2436
2830
2980
564
624
700
800
932
1036
1144
1300
1504
1812
2196
2840
4116
4540
4728
4728
19
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING INPUT GAIN
1. Adjust all amplifier input gain controls to just above minimum
sensitivity (fully counterclockwise).
2. Using the cleanest music source (CD) playing, turn up the head
unit source volume until you can hear distortion. Now turn it down a
bit until you cannot hear the distortion (usually just below full
volume).
3. Increase the amplifier gain (clockwise) until the onset of audible
distortion. Then decrease the gain to the point just before the
distortion starts. This setting minimizes background noise and
prevents overload.
4. Repeat step 3 for any remaining independently controlled
amplifiers (rear and subwoofer gain controls) in the system.
HIGH MASS INTERNAL HEATSINK
The unique heatsink on your amplifier has been designed with fins
on the inside of the aluminum extrusion. This allows for the transfer
of heat from the circuitry to the heatsink fins and out through the
vents in the endplates. Be sure you provide ample space around the
amplifier for cooling: at least 2” on all sides.
AP-IV PROTECTION CIRCUIT
Short Circuit Protection engaged: The amplifiers will turn off and try
to come back on immediately. The amplifier will cycle like this
indefinitely with “blips” of sound each time. If this is the case, check
your speakers and wiring for low impedance and short circuits.
Thermal Protection engaged. The amplifiers will turn off and after a
minute or so will come back on. In this case, ensure that there is
nothing blocking the normal convection airflow of the amplifier. No
obstruction should be within 2” of the amplifier on all sides.
Note: Low battery voltage will cause the amplifier to run
warmer and possibly damage the amplifier.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
NO SOUND Is the LED illuminated?
YES
NO
Check Power and Remote
turn-on wire for voltage.
Make sure the ground wire
is secure.
STILL NO SOUND
TM
See your Authorized Precision Power Dealer or call 1-800-62POWER.
SOUND IN ONE CHANNEL ONLY
Reverse the left and right speakers by unplugging the speaker connector,
turning it over and plugging it back in.
SOUND IS NOW IN
OPPOSITE CHANNEL
Reverse RCA inputs.
SAME CHANNEL
Problem is in the speaker or
speaker wire of the silent
channel.
SOUND IS NOW IN
OPPOSITE CHANNEL
Reverse RCA inputs
at head unit.
SAME CHANNEL
Problem is in the amplifier.
See your local Authorized
TM
Precision Power Dealer or
call 1-800-62POWER.
SOUND IS NOW IN
OPPOSITE CHANNEL
Problem is in the head
unit or before the amplifier.
SAME CHANNEL
Problem is in the RCA
cables.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED TWO YEAR CONSUMER WARRANTY:
Directed Electronics promises to the original purchaser, to replace this product
should it prove to be defective in workmanship or material under normal use, for
a period of two years from the date of purchase by the dealer as indicated by the
date code marking of the product PROVIDED the product was installed by an
authorized Directed dealer. During this two-year period, there will be no charge for
this replacement PROVIDED the unit is returned to Directed, shipping pre-paid. If
the unit is installed by anyone other than an authorized Directed dealer, the
warranty period will be 1 year from the date of purchase by the dealer as indicated
by the date code marking of the product. During this 1-year period there will be no
charge for this replacement PROVIDED the unit is returned to Directed, shipping
pre-paid.This warranty is non-transferable and does not apply to any unit that has
been modified or used in a manner contrary to its intended purpose, and does not
cover damage to the unit caused by installation or removal of the unit. This
warranty is void if the product has been damaged by accident or unreasonable
use, neglect, improper service or other causes not arising out of defects in
materials or construction. ALL WARRANTIES INCLUDING BUT NOT LIMITED
TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF
MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND
WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE
EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT ALLOWED BY LAW,
AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON TO
ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT. DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL
ACTS OF THIRD PARTIES INCLUDING ITS AUTHORIZED DEALERS OR
INSTALLERS. Unit must be returned to Directed, postage pre-paid, with:
consumer’s name, telephone number, and address, authorized dealer’s name and
address, and product description. IN ORDER FOR THIS WARRANTY TO BE
VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF INSTALLATION BY
AN AUTHORIZED DIRECTED DEALER. ALL UNITS RECEIVED BY DIRECTED
FOR WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER
INSTALLATION WILL BE COVERED BY THE LIMITED 1-YEAR PARTS AND
LABOR WARRANTY. Note: This warranty does not cover labor costs for the
removal and reinstallation of the unit. BY PURCHASING THIS PRODUCT, THE
CONSUMER AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE
CONSUMER AND Directed SHALL BE RESOLVED IN ACCORDANCE WITH
CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.
© 2005 Directed Electronics, All rights reserved. G48320.25.30 12-05
Download from Www.Somanuals.com. All Manuals Search And Download.
|