Poulan Snow Blower 430429 User Manual

IMPORTANT MANUAL

Do Not Throw Away

OWNER'S MANUAL

MODEL NUMBER:

WARNING:

Read the Owner's Manual and

follow all Warnings and Safety

Instructions. Failure to do so

can result in serious injury.

PP265E27

SNOW THROWER

430429 09.08.09 AP

Printed in the U.S.A.

Always Wear Eye Protection During Operation

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Whencleaning,repairingorinspectingthesnowthrower,

stop the engine and make certain the collector/impel-

ler and all moving parts have stopped. Disconnect the

sparkplugwireandkeepthewireawayfromtheplugto

preventsomeonefromaccidentallystartingtheengine.

7. Do not run the engine indoors, except when starting

the engine and for transporting the snow thrower in or

out of the building. Open the outside doors; exhaust

fumes are dangerous.

Clearing a Clogged Discharge Chute

Handcontactwiththerotatingimpellerinsidethedischarge

chute is the most common cause of injury associated with

snow throwers. Never use your hand to clean out the dis-

charge chute. To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

8. Exercise extreme caution when operating on slopes.

9. Neveroperatethesnowthrowerwithoutproperguards,

andothersafetyprotectivedevicesinplaceandworking.

3. Always use a clean-out tool, not your hands.

Maintenance and Storage

10. Never direct the discharge toward people or areas

where property damage can occur. Keep children and

others away.

1. Check shear bolts and other bolts at frequent intervals

for proper tightness to be sure the equipment is in safe

working condition.

11. Do not overload the machine capacity by attempting

to clear snow at too fast a rate.

12. Never operate the machine at high transport speeds

on slippery surfaces. Look behind and use care when

operating in reverse.

13. Disengage power to the collector/impeller when snow

thrower is transported or not in use.

14. Use only attachments and accessories approved by

the manufacturer of the snow thrower (such as wheel

weights, counterweights, or cabs).

2. Never store the machine with fuel in the fuel tank

inside a building where ignition sources are present

such as hot water heaters, space heaters, or clothes

dryers. Allow the engine to cool before storing in any

enclosure.

3. Always refer to operator’s manual for important details

if the snow thrower is to be stored for an extended

period.

4. Maintain or replace safety and instruction labels, as

necessary.

5. Run the machine a few minutes after throwing snow

to prevent freeze-up of the collector/impeller.

15. Never operate the snow thrower without good visibility

or light. Always be sure of your footing, and keep a firm

hold on the handles. Walk; never run.

16. Never touch a hot engine or muffler.

CONGRATULATIONS on your purchase of a new snow

thrower. Ithasbeendesigned,engineeredandmanufactured

to give best possible dependability and performance.

PRODUCT SPECIFICATIONS

Gasoline Capacity 0.5 Gallons (1,89 Liters)

and Type:

Unleaded Regular only

Should you experience any problem you cannot easily

remedy,pleasecontactyournearest servicecenter/depart-

ment. We have competent, well-trained technicians and

the proper tools to service or repair this unit.

Oil Type

(API SG–SL):

SAE 30 (above 50°F)

SAE 5W-30 or 10W-30 (32° to 50°F)

SAE 5W-30 (below 32°F)

Please read and retain this manual. The instructions will

enable you to assemble and maintain your snow thrower

properly. Always observe the “SAFETY RULES”.

Oil Capacity:

33.8 Ounces (1 Liters)

Spark Plug:

Gap:

Champion-RN9YC/NGK-BPR6ES

0.028-0.031" (0.7-0.8mm)

SERIAL NUMBER: ___________________________

DATE OF PURCHASE: _______________________

THEMODELANDSERIALNUMBERSWILLBEFOUND

ONADECALATTACHEDTOTHEREAROFTHESNOW

THROWER HOUSING.

CUSTOMER RESPONSIBILITIES

•

Read and observe the safety rules.

Follow a regular schedule in maintaining, caring for

and using your snow thrower.

YOUSHOULDRECORDBOTHSERIALNUMBERAND

DATE OF PURCHASE AND KEEP IN A SAFE PLACE

FOR FUTURE REFERENCE.

•

Follow the instructions under “Maintenance” and “Stor-

age” sections of this owner’s manual.

TABLE OF CONTENTS

SAFETY RULES ........................................................ 2-3

MAINTENANCE..................................................... 14-15

SERVICE AND ADJUSTMENTS........................... 16-18

STORAGE................................................................... 19

TROUBLESHOOTING................................................ 20

REPAIR PARTS ..................................................... 21-39

WARRANTY........................................................... 40-43

PRODUCT SPECIFICATIONS...................................... 3

CUSTOMER RESPONSIBILITIES................................ 3

ASSEMBLY / PRE-OPERATION ............................... 4-7

OPERATION ............................................................ 8-13

MAINTENANCE SCHEDULE ..................................... 14

Download from Www.Somanuals.com. All Manuals Search And Download.

PARTS PACKED SEPARATELY IN CARTON

(1) POWER CORD

(1) MULTI-

WRENCH

(180684)

(3) RETAINER

SPRINGS

(198563)

(169675)

(2) LOCKNUTS

1/4-20

(73800400)

(2) SHEAR BOLTS 1/4-20 x 1-3/4

(192090)

(2) FLAT WASHERS

SAFTEY

IGNITION KEY (S)

(428498)

(2) CARRIAGE BOLTS

3/8-16 x 2.25

(1) LOCKNUT

5/16-18

(1) CARRIAGE BOLT

5/16-18 x 5/8

(751153)

(72250505)

(1) LOCKNUT

1/4-20

(191730)

(1) SHOULDER

BOLT 1/4-20

(179829)

(1) LOCKNUT 3/8

(73800600)

(1) WASHER 3/8

(19131316)

(1) SPRING

(184505)

(2) HANDLE KNOBS

ASSEMBLY / PRE-OPERATION

Read these instructions and this manual in its entirety

before you attempt to assemble or operate your new

snow thrower. Reading the entire manual will familiar-

ize you with the unit, which will assist you in assembly,

operation and maintenance of the product.

2. Cut down all four corners of carton and lay panels flat.

3. Removethetwo(2)screwssecuringtheaugerhousing

to the pallet.

4. Removeallpackingmaterialsexceptplastictieholding

speed control rod to lower handle.

5. Remove the two (2) plastic ties securing the upper

handle to the pallet.

Your new snow thrower has been assembled at the factory

with the exception of those parts left unassembled for ship-

ping purposes. All parts such as nuts, washers, bolts, etc.,

necessary to complete the assembly have been placed in

the parts bag. To ensure safe and proper operation of your

snow thrower, all parts and hardware you assemble must

be tightened securely. Use the correct tools as necessary

to ensure proper tightness.

6. Remove snow thrower from carton and check carton

thoroughly for additional loose parts.

HOW TO SET UP YOUR SNOW THROWER

TOOL BOX (See Fig. 10)

A toolbox is provided on your snow thrower. The toolbox is

located on top of the belt cover. Store the extra shear bolts,

nuts and multi-wrench provided in parts bag in the toolbox.

REMOVE SNOW THROWER FROM CARTON

1. Remove all accessible loose parts and parts boxes

from carton.

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY / PRE-OPERATION

NOTE: The multi-wrench may be used for assembly of the

INSTALL TRACTION DRIVE CONTROL ROD

(See Figs. 3 and 4)

The traction drive control rod is installed on the snow

thrower.

chuterotatorheadtosnowthrowerandmakingadjustments

to the skid plates.

UNFOLD UPPER HANDLE

1. Raise upper handle to the operating position and

tighten handle knobs securely. Additional carriage

bolts, washers and handle knobs are in bag of parts.

Use to secure upper handle to lower handle. Install

in lower holes in handles.

1. Remove plastic tie securing rod to lower handle.

2. With top end of rod positioned under left side of control

panel, pushroddownandinserttopendofrodintohole

in drive control bracket. Secure with retainer spring.

INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)

PLASTIC TIE

1. Remove plastic tie securing rod to lower handle.

2. Insert rod into speed control bracket and secure with

retainer spring.

TRACTION DRIVE

CONTROL ROD

SPEED

CONTROL

ROD

VINYL

SLEEVE

PLASTIC TIE

UPPER

HANDLE

KNOB

LOWER

HANDLE

FIG. 3

TRACTION DRIVE

CONTROL LEVER

RETAINER

SPRING

FIG. 1

SPEED CONTROL ROD

TRACTION

DRIVE

RETAINER

SPRING

CONTROL

ROD

DRIVE

CONTROL

BRACKET

FIG. 4

SPEED

CONTROL

BRACKET

SPEED

CONTROL

LEVER

FIG. 2

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY / PRE-OPERATION

INSTALL DISCHARGE CHUTE / CHUTE ROTATOR

HEAD (See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may

be used to install the chute rotator head.

1. Place discharge chute assembly on top of chute base

with discharge opening toward front of snow thrower.

2. Positionchuterotatorheadoverchutebracket. Ifneces-

sary,rotatechuteassemblytoalignsquareandpinonun-

dersideofchuterotatorheadwithholesinchutebracket.

3. With chute rotator head and chute bracket aligned,

position chute rotator head on pin and threaded stud

of mounting bracket.

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

1. Retrieve vinyl sleeve and spring from bag of parts and

retrieve the auger control rod from carton chute tray.

Slide straight rod end through the small hole in the

vinyl sleeve. Hook spring in hole in rod end.

2. Hook end of spring into control arm with loop opening

up as shown. (See Fig. 5)

3. With top end of rod positioned under right side of

control panel, push down on rod and insert end of rod

into hole in auger control bracket. Secure with retainer

spring.

4. Install 3/8 washer and locknut on threaded stud and

tighten securely.

AUGER

CONTROL

ROD

CHUTE

ROTATOR

HEAD

3/8 LOCKNUT

3/8 WASHER

VINYL

SLEEVE

CONTROL

ARM

THREADED

STUD

LOOP

OPENING

ROTATOR HEAD

MOUNTING

ALIGN BEFORE

TIGHTENING LOCKNUT

CHUTE

BRACKET

FIG. 7

FIG. 5

AUGER CONTROL ROD

AUGER

CONTROL

LEVER

RETAINER

SPRING

AUGER

CONTROL

BRACKET

FIG. 6

Download from Www.Somanuals.com. All Manuals Search And Download.

ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL

(See Figs. 8 and 9)

1. Install remote cable bracket to discharge chute with

5/16-18 carriage bolt and 5/16-18 locknut as shown.

Tighten securely.

2. Install remote cable eyelet to chute deflector with

1/4-20 shoulder bolt and 1/4-20 locknut as shown.

Tighten nut securely. Cable eyelet will be loose on

shoulder bolt.

3. Install spring hooks between hex nuts on chute rotater

head and into hole in chute deflector as shown.

SPRING

1/4-20

CHUTE

SHOULDER

DEFLECTOR

BOLT

HOOK

BETWEEN

HEX NUTS

ON CHUTE

ROTATER

HEAD

1/4-20

LOCKNUT

5/16-18

CARRIAGE

BOLT

CABLE

EYELET

REMOTE

CABLE

BRACKET

5/16-18

LOCKNUT

FIG. 8

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 9

CHECK TIRE PRESSURE

Thetiresonyoursnowthrowerwereoverinflatedatthefac-

tory for shipping purposes. Correct and equal tire pressure

is important for best snow throwing performance.

•

Reduce tire pressure to 14-17 PSI.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

KNOW YOUR SNOW THROWER

READ THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare

the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save

this manual for future reference.

These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand

their meaning.

PRIMER

DANGER

OR WARNING

READ AND FOLLOW ALL SAFETY INFORMATION

AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.

KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.

FORWARD REVERSE

IGNITION KEY.

INSERT TO START

AND RUN,

PULL OUT TO STOP.

DISENGAGED

ENGAGED

SNOW

TRACTION

DISCHARGE

DRIVE CONTROL

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

POWER

CORD

PLUG

AUGER

DISCHARGE CHUTE CONTROL LEVER

GASOLINE

FILLER

CAP

CONTROL

LEVER

DEFLECTOR REMOTE

DRIVE SPEED

CONTROL LEVER

ELECTRIC

PRIMER

START

BUTTON

TRACTION

DRIVE

CONTROL

LEVER

CHUTE

DEFLECTOR

CHOKE

CON-

TROL

SAFETY

IGNITION KEY

DISCHARGE

CHUTE

LIGHT

FUEL SHUT-OFF VALVE

THROTTLE

RECOIL (AUXILIARY) STARTER HANDLE

CLEAN-OUT TOOL

HANDLE

KNOB

MUFFLER

TOOLBOX

NOTE: ITEMS ABOVE

ARE SHOWN IN

THEIR TYPICAL

LOCATION ON THE

ENGINE. ACTUAL

LOCATION MAY

VARY WITH THE

ENGINE ON YOUR

UNIT.

SKID PLATE

AUGERS

FIG. 10

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and

wrench.

Drive speed control lever - used to select forward or

reverse motion and speed of snow thrower.

Safety ignition key - must be inserted for the engine to

start and run. Remove when snow thrower is not in use.

Traction drive control lever - used to engage power-

propelled forward or reverse motion of snow thrower.

Electric start button - used for starting the engine.

Auger control lever - used to engage auger motion (throw

snow).

Recoil(auxiliary)starterhandle-usedforstartingengine.

Dischargechutecontrollever-usedtochangethedirec-

tion the snow is thrown.

Primer - pumps additional fuel from the carburetor to the

cylinder for use when starting a cold engine.

Deflector remote control lever - used to change the

distance the snow is thrown.

Throttle- used to select FAST or SLOW engine speeds.

Choke Control - used for starting a cold engine.

Skid plate - used to adjust height of scraper bar from the

ground.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

The operation of any snow thrower can result

TO USE THROTTLE CONTROL (See Fig. 13)

in foreign objects thrown into the eyes, which

canresultinsevereeyedamage. Alwayswear

Thethrottlecontrolislocatedontheengine.Alwaysoperate

the snow thrower with the engine at full throttle. Full throttle

offers the best snow thrower performance.

safety glasses or eye shields while operating

your snow thrower or performing any adjust-

ments or repairs. We recommend standard safety glasses

or a wide vision safety mask worn over spectacles.

HOW TO USE YOUR SNOW THROWER

Know how to operate all controls before adding fuel or

attempting to start the engine.

FIG. 13

STOPPING

TO CONTROL SNOW DISCHARGE (See Fig. 14)

TRACTION DRIVE

•

Release traction drive control lever to stop the forward

or reverse movement of the snow thrower.

WARNING: Snow throwers have ex-

posed rotating parts, which can cause

severeinjuryfromcontact, orfromma-

terialthrownfromthedischargechute.

Keep the area of operation clear of all

persons, small children and pets at all

times including startup.

AUGER

•

Release the auger control lever to stop throwing snow.

ENGINE

1. Move throttle control to “STOP” position.

2. Remove (do not turn) safety ignition key to prevent

unauthorized use.

WARNING: If the discharge chute or

augerbecomeclogged,shut-offengine

andwaitforallmovingpartstostop.Use

the clean-out tool, NOT YOUR HANDS,

to unclog the chute and/or auger.

NOTE: Never use choke to stop engine.

TO USE FUEL SHUT-OFF VALVE (See Fig. 11)

The fuel shut-off valve is located beneath the fuel tank on

the engine. Always operate the snow thrower with the fuel

shut-off valve in the OPEN position.

TheDIRECTIONinwhichsnowistobethrowniscontrolled

by the discharge chute control lever.

•

To change the discharge chute position, press down-

ward on discharge chute control lever and move lever

left or right until chute is in desired position. Be sure

lever springs back and locks into desired position.

OFF

The DISTANCE that snow is thrown is controlled by the

position of the chute deflector. Set the deflector low to

throw snow a short distance; set the deflector higher to

throw snow farther.

•

Press downward on chute deflector control lever and

move lever forward to raise the deflector and increase

the distance. Move lever back to lower the deflector

and decrease the distance. Be sure lever springs back

and locks into desired position.

FIG. 11

TO USE CHOKE CONTROL (See Fig. 12)

DISCHARGE CHUTE

CONTROL LEVER

The choke control is located on the engine. Use the choke

control whenever you are starting a cold engine. Do not

use to start a warm engine.

•

To engage choke, rotate lever to “FULL” position.

CHUTE DEFLECTOR

REMOTE CONTROL LEVER

FIG. 14

FIG. 12

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

TO THROW SNOW (See Fig. 15)

TO MOVE FORWARD AND BACKWARD (See Fig. 17)

The auger rotation is controlled by the auger control lever

located on the right side handle.

SELF-PROPELLING, forward and reverse movement of

the snow thrower, is controlled by the traction drive control

lever located on the left side handle.

•

Squeeze auger control lever to handle to engage the

auger and throw snow.

•

Squeezetractiondrivecontrollevertohandletoengage

the drive system.

•

Release the auger control lever to stop throwing snow.

•

Release traction drive control lever to stop the forward

or reverse movement of the snow thrower.

AUGER

CONTROL

LEVER

SPEED and DIRECTION are controlled by the drive speed

control lever.

•

Press downward on the speed control lever and move

lever to desired position BEFORE engaging the trac-

tion drive control lever. Be sure lever springs back and

locks into desired position.

CAUTION: Do not move speed control lever

when traction drive control lever is engaged.

Damage to the snow thrower can result.

FIG. 15

USING THE CLEAN-OUT TOOL (See Fig. 16)

•

Slower speeds are for heavier snow and faster speeds

are for light snow and transporting the snow thrower. It

is recommended that you use a slower speed until you

are familiar with the operation of the snow thrower.

In certain snow conditions, the discharge chute may be-

come clogged with ice and snow. Use the clean-out tool

to dislodge this blockage.

NOTE: When both traction drive and auger control levers

are engaged, the traction drive control lever will lock the

auger control lever in the engaged position. This will allow

you to release your right hand from the handle and adjust

the discharge chute direction without interrupting the snow

throwing process.

When cleaning, repairing, or inspecting, make

certain all controls are disengaged and the au-

ger/impellerandallmovingpartshavestopped.

Disconnect the spark plug wire and keep the

wire away from the spark plug to prevent ac-

cidental starting.

TRACTION DRIVE

CONTROL LEVER

•

Releasetheaugercontrolleverandshutofftheengine.

Removetheclean-outtoolfromit'smountingclip. Grasp

the tool firmly by the handle and push and twist the tool

into the discharge chute to dislodge the blockage.

Afterthepackedsnowhasbeendislodged,returntheclean-

out tool to it's mounting clip by pushing it into the clip.

•

Make sure the discharge chute is pointed in a safe di-

rection(novehicles, buildings, people, orotherobjects

are in the direction of discharge) before restarting the

engine.

•

Restart the engine, then squeeze the auger control

lever to the handle to clear snow from the auger hous-

ing and the discharge chute.

DRIVE SPEED

CONTROL LEVER

DISCHARGE CHUTE

FIG. 17

CLEAN-OUT

TOOL

MOUNTING

CLIP

FIG. 16

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

TO ADJUST SKID PLATES (See Fig. 18)

ADD GASOLINE (See Fig. 19)

•

Fill fuel tank to bottom of tank filler neck. Do not over-

fill. Use fresh, clean, regular unleaded gasoline with

a minimum of 87 octane. Do not mix oil with gasoline.

Purchase fuel in quantities that can be used within 30

days to assure fuel freshness.

NOTE: The wrench provided in your parts bag may be

used to adjust the skid plates.

Skid plates are located on each side of the auger housing

and adjust the clearance between the scraper bar and the

ground surface. Adjust skid plates evenly to proper height

for current surface conditions. For removal of snow in

normal conditions, such as a paved driveway or sidewalk,

place skid plates in the highest position (lowest scraper

clearance) to give a 1/8" clearance between the scraper

bar and the ground. Use a middle position if the surface

to be cleared is uneven.

WARNING: Wipe off any spilled oil or

fuel. Do not store, spill or use gasoline

near an open flame.

CAUTION:Alcoholblendedfuels(calledgasohol

or using ethanol or methanol) can attract mois-

ture which leads to separation and formation of

acids during storage. Acidic gas can damage

the fuel system of an engine while in storage. To

avoid engine problems, the fuel system should

be emptied before storage of 30 days or longer.

Emptythegastank, starttheengineandletitrun

untilthefuellinesandcarburetorareempty. Use

freshfuelnextseason. SeeStorageInstructions

for additional information. Never use engine or

carburetor cleaner products in the fuel tank or

permanent damage may occur.

NOTE: It is not recommended to operate the snow thrower

overgravelorrockysurfaces.Objectssuchasgravel,rocks

or other debris, can easily be picked up and thrown by the

impeller, which can cause serious personal injury, property

damage or damage to the snow thrower.

•

If snow thrower must be operated over gravel surface,

use extra caution and be sure skid plates are adjusted

to lowest (highest scraper clearance) position.

1. Shut off engine and wait for all moving parts to stop.

2. Adjust skid plates by loosening the hex nuts, then

moving skid plate to desired position. Be sure both

plates are adjusted evenly. Tighten securely.

ENGINE OIL FILL

CAP / DIPSTICK

HIGH POSITION

(LOW GROUND

CLEARANCE)

PRIMER

GASOLINE

FILLER CAP

AUGER

HOUSING

POWER

CORD

PLUG

SCRAPER BAR

HEX

SKID PLATE

NUTS

LOW POSITION (HIGH GROUND CLEARANCE)

RECOIL

(AUXILIARY)

STARTER

CHOKE

CONTROL

FIG. 18

HANDLE

SAFETY

IGNITION KEY

SCRAPER BAR (See Fig. 18)

The scraper bar is not adjustable, but is reversible. After

considerable use it may become worn. When it has worn

almost to the edge of the housing, it can be reversed,

providing additional service before requiring replacement.

Replace a damaged or worn scraper bar.

FUEL SHUT-OFF

VALVE

THROTTLE

NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.

ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.

FIG. 19

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL (See Fig. 19)

The engine on your snow thrower has been shipped, from

the factory, already filled with oil.

1. Check engine oil with snow thrower on level ground.

2. Remove oil fill cap/dipstick and wipe clean, reinsert

the dipstick and screw tight, wait for a few seconds,

remove and read oil level. If necessary, add oil until

“FULL” mark on dipstick is reached. Do not overfill.

TO START ENGINE

•

Be sure fuel shut-off valve is in the “OPEN” position.

Your snow thrower engine is equipped with both a 120 Volt

A.C. electric starter and a recoil starter. The electric starter

is equipped with a three-wire power cord and plug and is

designed to operate on 120 Volt A.C. household current.

•

Be sure your house is a 120 Volt A.C. three-wire

grounded system. If you are uncertain, consult a

licensed electrician.

•

To change engine oil, see “TO CHANGE ENGINE OIL”

in the Maintenance section of this manual.

WARNING: Do not use the electric

starter if your house is not a 120 Volt

A.C.three-wiregroundedsystem. Seri-

ous personal injury or damage to your

snow thrower could result.

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

COLD START - ELECTRIC STARTER

IF RECOIL STARTER HAS FROZEN

If the recoil starter has frozen and will not turn the engine,

proceed as follows:

1. Grasp the recoil starter handle and slowly pull as much

rope out of the starter as possible.

2. Release the recoil starter handle and let it snap back

against the starter.

1. Insert safety ignition key (tied to recoil start cord) into

ignition slot until it clicks. DO NOT turn the key. Keep

the extra safety ignition key in a safe place.

2. Place throttle control in “FAST” position.

3. Rotate choke control to “FULL” position.

4. Connect the power cord to the engine.

If the engine still fails to start, repeat the above steps or

use the electric starter.

5. Plug the other end of the power cord into a three-hole

grounded 120 Volt A.C. receptacle.

SNOW THROWING TIPS

NOTE: Do not use primer when starting engine with the

electric starter.

•

Always operate the snow thrower with the engine at

full throttle. Full throttle offers the best performance.

Goslowerindeep,freezingorheavywetsnow.Usethe

drive speed control, NOT the throttle, to adjust speed.

It is easier and more efficient to remove snow imme-

diately after it falls.

The best time to remove snow is the early morning. At

this time the snow is usually dry and has not been ex-

posed to the direct sun and warming temperatures.

6. Push starter button until engine starts.

IMPORTANT: Do not crank engine more than five continu-

ous seconds between each time you try to start. Wait 5 to

10 seconds between each attempt.

7. When the engine starts, release the starter button and

slowly move the choke control to the “OFF” position.

8. Disconnect the power cord from the receptacle first,

then from the engine.

•

Slightly overlap each successive path to ensure all

snow will be removed.

Allow the engine to warm up for a few minutes. Engine will

not develop full power until it has reached normal operat-

ing temperature.

•

Throw snow downwind whenever possible.

Adjust the skid plates to proper height for current snow

conditions. See “TO ADJUST SKID PLATES” in this

section of this manual.

WARM START - ELECTRIC STARTER

Follow the steps above, keeping the choke control in the

“OFF” position.

•

For extremely heavy snow, reduce the width of snow

removal by overlapping previous path and moving

slowly.

COLD START - RECOIL STARTER

1. Insert safety ignition key (tied to recoil start cord) into

ignition slot until it clicks. DO NOT turn the key. Keep

the extra safety ignition key in a safe place.

2. Place throttle control in “FAST” position.

3. Rotate choke control to “FULL” position.

4. Push the primer four (4) times if the temperature is

below 15°F, or two (2) times if temperature is between

15° and 50°F. If temperature is above 50°F, priming is

not necessary.

•

Keep engine clean and clear of snow during use. This

will help air flow and extend engine life.

Aftersnow-throwingiscompleted,allowenginetorunfor

a few minutes to melt snow and ice off the engine.

Clean the entire snow thrower thoroughly after each

use and wipe dry so it is ready for next use.

WARNING: Do not operate snow

thrower if weather conditions impair

visibility. Throwing snow during a

heavy, windy snowstorm can blind

you and be hazardous to the safe

operation of the snow thrower.

NOTE: Over priming may cause flooding, preventing the

engine from starting. If you do flood the engine, wait a few

minutes before attempting to start and DO NOT push the

primer.

5. Pull recoil starter handle quickly. Do not allow starter

rope to snap back.

6. Whentheenginestarts,releasetherecoilstarterhandle

and slowly move the choke control to the “OFF” posi-

tion.

Allow the engine to warm up for a few minutes. Engine will

not develop full power until it has reached normal operat-

ing temperature.

WARM START - RECOIL STARTER

Follow the steps above, keeping the choke in the “OFF”

position. DO NOT push the primer.

BEFORE STOPPING

Run the engine for a few minutes to help dry off any mois-

ture on the engine.

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

Thewarrantyonthissnowthrowerdoesnotcoveritemsthat

have been subjected to operator abuse or negligence. To

receivefullvaluefromthewarranty,operatormustmaintain

snow thrower as instructed in this manual. Some adjust-

mentswillneedtobemadeperiodicallytoproperlymaintain

your snow thrower.

➀ SAE 5W-30 Motor Oil

See “ENGINE” in

➁

Maintenance section

General

Purpose

Grease

➂

At least once a season, check to see if you should make

any of the adjustments described in the Service and Ad-

justments section of this manual.

•

At least once a year, you should replace the spark plug

and check belts for wear. A new spark plug will help

your engine run better and last longer.

➀ Pivot points

•

Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM)

parts to service this unit. Failure to do so can cause the unit

to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1. Check engine oil level.

2. Check for loose fasteners.

3. Checkcontrolstobesuretheyarefunctioningproperly.

LUBRICATION

Keep your snow thrower well lubricated

(See “LUBRICATION CHART”).

➁

Engine oil

➂ Auger

grease fittings

SNOW THROWER

Always observe the safety rules when performing any

maintenance.

•

Keep tires free of gasoline and oil, which can harm

rubber.

NOTE: To seal tire punctures and prevent flat tires due to

slow leaks, tire sealant may be purchased from your local

parts dealer. Tire sealant also prevents tire dry rot and

corrosion.

TIRES

•

Maintain proper air pressure in both tires (14–17 PSI).

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

BELTS

TO CHANGE ENGINE OIL

Check belts for deterioration and wear after every 50 hours

of operation and replace if necessary. The belts are not

adjustable. Replace belts if they begin to slip from wear.

(See “TO REMOVE BELT COVER” in the Service and

Adjustments section of this manual).

Determine temperature range anticipated before next oil

change.AlloilmustmeetAPIserviceclassificationSG–SL.

•

Be sure snow thrower is on level surface.

Oil will drain more freely when warm.

Catch oil in a suitable container.

The belts on your snow thrower are of special construction

andshouldbereplacedbyoriginalequipmentmanufacturer

(OEM)beltsavailablefromyournearestdealer.Usingother

than OEM belts can cause personal injury or damage to

the snow thrower.

NOTE: The left side wheel may be removed from snow

thrower for easier access to the oil drain plug and place-

ment of a suitable container. The unit tilted, resting on the

frame with the left wheel removed, will help drain any oil

trapped inside the engine. (See “TO REMOVE WHEELS”

in the Service and Adjustments section of this manual).

1. Remove safety ignition key and disconnect spark plug

wire from spark plug. Place wire where it cannot come

in contact with plug.

AUGER GEAR CASE

•

The gear case was filled with lubricant to the proper

level at the factory. The only time the lubricant needs

attention is if service has been performed on the gear

case.

•

If lubricant is required, use only Ronex ED #1 grease.

2. Clean area around drain plug.

3. Remove drain plug and drain oil in a suitable container.

4. Install drain plug and tighten securely.

5. Wipe off any spilled oil from snow thrower and engine.

6. Install left wheel (if removed for draining oil). Be sure to

install klick pin into proper hole in wheel axle (See “TO

REMOVE WHEELS” in the Service and Adjustments

section of this manual).

7. Remove oil fill cap/dipstick. Be careful not to allow dirt

to enter the engine.

TRACTION DRIVE SYSTEM

DO NOT lubricate the drive components inside the snow

thrower. The sprockets, hex shafts, drive disc and friction

wheel require no lubrication. The bearings and bushings

are lifetime lubricated and require no maintenance.

CAUTION:Anylubricatingoftheabovecompo-

nents can cause contamination of the friction

wheel and damage to the drive system of your

snow thrower.

8. Refill engine with oil through oil dipstick tube. Pour

slowly. Do not overfill. For approximate capacity see

“PRODUCTSPECIFICATIONS”sectionofthismanual.

ENGINE

LUBRICATION

9. Use gauge on oil fill cap/dipstick for checking level. Be

sure dipstick cap is tightened securely for accurate

reading. Keep oil at “FULL” line on dipstick.

Use only high quality detergent oil rated with API service

classification SG–SL. Select the oil's SAE viscosity grade

according to your expected operating temperature.

10. Wipe off any spilled oil.

MUFFLER

Inspect and replace corroded muffler as it could create a

fire hazard and/or damage.

SPARK PLUG

Replacesparkplugatthebeginningofeachseasonorafter

every100hoursofoperation,whicheveroccursfirst. Spark

plug type and gap setting are shown in the “PRODUCT

SPECIFICATIONS” section of this manual.

CLEANING

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)

improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption when used above

32°F/0°C. Check your engine oil level more frequently to

avoid possible engine damage from running low on oil.

IMPORTANT: For best performance, keep snow thrower

housing free of any dirt or trash. Clean the outside of your

snow thrower after each use.

WARNING: Removesafetyignitionkey

and disconnect spark plug wire from

spark plug and place wire where it can-

not come in contact with plug.

Change the oil after every 25 hours of operation or at least

once a year if the snow thrower is not used for 25 hours

in one year.

Checkthecrankcaseoillevelbeforestartingtheengineand

after each five (5) hours of continuous use. Tighten oil fill

cap / dipstick securely each time you check the oil level.

•

Keepfinishedsurfaces/wheelsfreeofgasoline,oil,etc.

We do not recommend using a garden hose to clean

yoursnowthrowerunlesstheelectricalsystem,muffler

and carburetor are covered to keep water out. Water

in engine can result in shortened engine life.

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

1. Disengage all controls and move throttle control to

WARNING: To avoid serious injury, before

performing any service or adjustments:

STOP position. Wait for all moving parts to stop.

2. Remove safety ignition key and disconnect spark plug

wire from spark plug. Place wire where it cannot come

in contact with spark plug.

3. Align holes in impeller hub with holes in impeller shaft

and install two (2) new 1/4-20 x 1-5/8" capscrew/shear

bolts. Install 1/4-20 locknuts and tighten securely.

1. Be sure throttle is in STOP position.

2. Remove safety ignition key.

3. Make sure the augers and all moving

parts have completely stopped.

4. Disconnect spark plug wire from

spark plug and place wire where it

cannot come in contact with plug.

CAUTION: Do not substitute. Use only original

equipment capscrew/shear bolts as supplied

with your snow thrower.

SNOW THROWER

TO ADJUST SNOW THROWER HEIGHT

4. Insertsafetyignitionkeyandreconnectsparkplugwire

to spark plug.

See “TO ADJUST SKID PLATES” and “SCRAPER BAR”

in the Operation section of this manual.

CHUTE DEFLECTOR

1/4-20

LOCKNUT

1/4-20 x 1-5/8

CAPSCREW /

SHEAR BOLT

1/4-20 x 2

SHOULDER /

SHEAR BOLT

The chute deflector, attached to the top of the discharge

chute, is provided to direct discharging snow away from

the operator. If the deflector becomes damaged, it should

be replaced.

IMPELLER HUB

IMPELLER

SHAFT

WARNING: To avoid serious injury,

never operate your snow thrower with

the deflector removed or damaged.

•

Tochangedirectionand/ordistancesnowisdischarged,

see “TO CONTROL SNOW DISCHARGE” in the Op-

eration section of this manual.

AUGER

HUB

SHEAR BOLTS (See Fig. 20)

AUGER SHEAR BOLTS

1/4-20

LOCKNUT

AUGER HUB

FIG. 20

AUGER SHAFT

Both right and left-hand augers are secured to the auger

shaftwithaspacer, shearboltandhexnut. Shouldaforeign

object or ice become lodged in the augers, the shear bolts

are designed to break, preventing damage to any other

components. If one or both augers do not turn when auger

control lever is engaged, check to see if one or both of the

bolts have sheared. To replace the shear bolts:

TO REMOVE BELT COVER (See Fig. 21)

1. Remove the two (2) screws securing belt cover to

frame.

2. Remove belt cover.

•

Replace belt cover by installing cover and screws and

tighten securely.

1. Disengage all controls and move throttle control to

STOP position. Wait for all moving parts to stop.

2. Remove safety ignition key and disconnect spark plug

wire from spark plug. Place wire where it cannot come

in contact with spark plug.

BELT

COVER

3. Align hole in auger hub with hole in auger shaft and

install a new 1/4-20 x 2" shear bolt. Install 1/4-20

lock nut and tighten securely.

CAUTION: Do not substitute. Use only original

equipment shear bolts as supplied with your

snow thrower.

4. Insertsafetyignitionkeyandreconnectsparkplugwire

to spark plug.

IMPELLER SHEAR BOLTS

The impeller is secured to the impeller shaft with two (2)

capscrew/shearboltsandhexnuts. Shouldaforeignobject

or ice become lodged in the impeller, the capscrews are

designed to break, preventing damage to any other com-

ponents. If impeller does not turn when auger control lever

is engaged, check to see if the capscrews have sheared.

To replace the capscrew/shear bolts:

FRAME

SCREWS

FIG. 21

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

TO REPLACE BELTS (See Fig. 22)

8. RELIEVE TENSION ON TRACTION DRIVE BELT

IDLER and remove traction drive belt from around

pulleys.

The auger and traction drive belts are not adjustable. If the

belts are damaged or begin to slip from wear, they should

be replaced. It is recommended that the belt(s) be replaced

by a service center/department.

HINT: Insert a 3/8" drive ratchet (in the “ON” position) into

the square hole in idler arm and rotate ratchet clockwise

to relieve tension.

9. With tension relieved on idler, install new traction drive

belt around pulleys and inside belt keepers.

10. Install clutch rod in swing plate; secure with hairpin.

11. Placeaugerbeltaroundandinsidethegrooveofauger

pulley only.

12. While your assistant slowly raises handles to rejoin

the auger housing and frame assembly, pull up on the

auger belt and squeeze sides together above pulley

so belt is fully seated in groove of pulley.

13. Move idler arm so it does not hit impeller pulley as you

bring snow thrower completely together and check

carefully for proper routing of belts. If auger belt has

becomedislodgedfromthepulley(bycatchingtheidler

arm bracket while bringing snow thrower together),

separate the snow thrower and repeat step 12. Belt

must be fully seated in pulley groove when bringing

the snow thrower together.

NOTE: It is recommended that both the auger and traction

drive belt be replaced at the same time.

The V-belts on your snow thrower are of special construc-

tion and should be replaced by original equipment manu-

facturer (OEM) belts available from your nearest service

center/department. Using other than OEM belts can cause

personal injury or damage to the snow thrower.

WARNING: Belt replacement requires

separation of the snow thrower. While

separating the auger housing from the

frame assembly, it is important that

an assistant stand in the operating

position and hold the snow thrower

handles. Serious personal injury and/

or damage to the unit could occur if the

snowthrowershouldfallduringthebelt

changing process.

FRAME

ASSEMBLY

AUGER

HOUSING

14. Install the two (2) hex bolts and tighten securely.

15. INSTALLENGINEPULLEY-Placebeltinpulleygroove

and slide pulley on crankshaft. Install flat washer, bolt

and tighten securely (41-47 N-m torque). Make sure

belt is inside belt keeper.

16. INSTALL BELT COVER and two (2) screws. Tighten

securely.

17. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-

CHARGE CHUTE / CHUTE ROTATER HEAD” in the

Assembly / Pre-Operation section of this manual.

HANDLES

1. REMOVE GASOLINE FROM FUEL TANK - Drain

gasoline from fuel tank into a suitable container, out-

doors, away from fire or flame. Wipe up any spilled

gasoline.

BELT KEEPER

TRACTION DRIVE BELT

ENGINE

2. REMOVE DISCHARGE CHUTE - Loosen locknut

securing chute rotator head to mounting bracket only

enough to allow chute rotator head to be raised and

discharge chute to be removed from snow thrower.

3. REMOVE BELT COVER - See “TO REMOVE BELT

COVER” in this section of this manual.

4. REMOVEENGINEPULLEY-Removebolt,flatwasher

securingpulleytoenginecrankshaft. Removeoutside

(auger) pulley only from crankshaft.

5. SEPARATE SNOW THROWER - With your assistant

standing in the operating position holding the handles,

remove the two (2) bolts holding the auger housing

and frame together.

FLAT WASHER

PULLEY

BOLT

AUGER

BELT

IDLER ARM

SQUARE

HOLE

CLUTCHING

IDLER ARM

BRACKET

AUGER

HOUSING

FRAME

AUGER PULLEY

BOLTS

WARNING: As the last bolt is removed,

haveyourassistantcarefullylowerthe

handles down to the ground.

6. REMOVE HAIRPIN FROM CLUTCH ROD and re-

move clutch rod from swing plate. Tip swing plate

forward.

7. REMOVE AUGER BELT from around pulley.

FIG. 22

Download from Www.Somanuals.com. All Manuals Search And Download.

SERVICE AND ADJUSTMENTS

TO REMOVE WHEELS (See Fig. 23)

Remove the klik pin and remove wheel from axle.

ENGINE

•

SEE ENGINE MANUAL.

CARBURETOR

Your carburetor is not adjustable. Engine performance

should not be affected at altitudes up to 2,134 meters. If

your engine does not operate properly due to suspected

carburetor problems, take your snow thrower to a service

center/department.

IMPORTANT: When installing wheel, be sure to use the in-

nermost hole in axle and the wheel hub hole. To disengage

drive system from the wheels (for pushing or transporting

the snow thrower), remove klik pin from wheel hub and

insert pin into the outermost hole in axle only.

NOTE: To seal punctures or prevent flat tires due to slow

leaks, tire sealant may be purchased from your local parts

dealer. Tire sealant also prevents tire dry rot and corrosion.

ENGINE SPEED

Never tamper with the engine governor, which is factory set

for proper engine speed. Overspeeding the engine above

the factory high speed setting can be dangerous and will

void the warranty. If you think the engine-governed high

speed needs adjusting, contact a service center/depart-

ment, which has the proper equipment and experience to

make any necessary adjustments.

KLIK PIN

OUTER HOLE

INNER

HOLE

WHEEL

WHEEL HUB

FIG. 23

TO ADJUST CABLE TENSION (See Fig. 24)

Adjust cable tension by turning the adjuster turn buckle,

located on the right hand cable. Grasp the long section

tightly and turn the short section to lengthen the adjuster.

Adjust until cable is snug.

ADJUSTER TURN

BUCKLE

FIG. 24

Download from Www.Somanuals.com. All Manuals Search And Download.

STORAGE

Immediately prepare your snow thrower for storage at

•

Empty the fuel tank by starting the engine and letting

the end of the season or if the unit will not be used for 30

it run until the fuel lines and carburetor are empty.

days or more.

Never use engine or carburetor cleaner products in the

fuel tank or permanent damage may occur.

Use fresh fuel next season.

WARNING: Never store the snow

throwerwithgasolineinthetankinside

a building where fumes may reach an

open flame, spark or pilot light as on a

furnace, water heater, clothes dryer or

gasappliance. Allowtheenginetocool

before storing in any enclosure.

NOTE: Fuel stabilizer is an acceptable alternative in min-

imizing the formation of fuel gum deposits during storage.

Add stabilizer to gasoline in fuel tank or storage container.

Always follow the mix ratio found on stabilizer container.

Run engine at least 10 minutes after adding stabilizer to

allow the stabilizer to reach the carburetor. Do not empty

the gas tank and carburetor if using fuel stabilizer.

SNOW THROWER

When snow thrower is to be stored for a period of time,

clean it thoroughly, remove all dirt, grease, leaves, etc.

Store in a clean, dry area.

1. Clean entire snow thrower (See “CLEANING” in the

Maintenance section of this manual).

ENGINE OIL

Drain oil (with engine warm) and replace with clean en-

gine oil. (See “ENGINE” in the Maintenance section of

this manual).

CYLINDER

1. Remove spark plug.

2. Pour approximately one ounce (30 ml) of oil through

spark plug hole into cylinder.

3. Pullrecoilstarterhandleslowlyafewtimestodistribute

oil.

2. Inspect and replace belts, if necessary (See “TO RE-

PLACEBELTS”intheServiceandAdjustmentssection

of this manual).

3. Lubricate as shown in the Maintenance section of this

manual.

4. Besurethatallnuts,bolts,screws,andpinsaresecurely

fastened. Inspect moving parts for damage, breakage

and wear. Replace if necessary.

5. Touch up all rusted or chipped paint surfaces; sand

lightly before painting.

4. Replace with new spark plug.

OTHER

•

Remove safety ignition key; store in a safe place.

Do not store gasoline from one season to another.

Replace your gasoline can if your can starts to rust.

Rust and/or dirt in your gasoline will cause problems.

ENGINE

FUEL SYSTEM

•

If possible, store your snow thrower indoors and cover

it to protect it from dust and dirt.

Cover your snow thrower with a suitable protective

cover that does not retain moisture. Do not use plastic.

Plastic cannot breathe, which allows condensation to

form and will cause your snow thrower to rust.

IMPORTANT: It is important to prevent gum deposits

from forming in essential fuel system parts such as

carburetor, fuel hose, or tank during storage. Alcohol

blended fuels (called gasohol or using ethanol or metha-

nol) can attract moisture which leads to separation and

formation of acids during storage. Acidic gas can dam-

age the fuel system of an engine while in storage.

IMPORTANT: Never cover snow thrower while engine/

exhaust area is still warm.

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

See appropriate section in manual unless directed to an authorized service center/department.

PROBLEM

CAUSE

CORRECTION

Does not start

1. Fuel shut-off valve (if so

equipped) in OFF position.

2. Safety ignition key

is not inserted.

1. Turn fuel shut-off valve to OPEN position.

2. Insert safety ignition key.

3. Out of fuel.

3. Fill fuel tank with fresh, clean gasoline.

4. Move throttle to FAST position

5. Move to FULL position.

6. Prime as instructed in the Operation section of this manual.

7. Wait a few minutes before restarting, DO NOT prime.

8. Connect wire to spark plug.

4. Throttle in STOP position

5. Choke in OFF position.

6. Primer not depressed.

7. Engine is flooded.

8. Spark plug wire is

disconnected.

9. Bad spark plug.

10. Stale fuel.

11. Water in fuel.

9. Replace spark plug.

10. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

11. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

Loss of power

1. Spark plug wire loose.

2. Throwing too much snow.

3. Fuel tank cap is covered

with ice or snow.

1. Reconnect spark plug wire.

2. Reduce speed and width of swath.

3. Remove ice and snow on and around fuel tank cap.

4. Dirty or clogged muffler.

4. Clean or replace muffler.

Engine idles or

runs roughly

1. Choke is in FULL position.

2. Blockage in fuel line.

3. Stale fuel.

4. Water in fuel.

5. Carburetor is in need of

adjustment or overhaul.

1. Move choke to OFF position.

2. Clean fuel line.

3. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

4. Empty fuel tank & carburetor, refill with fresh, clean gasoline.

5. Contact an authorized service center/department.

Excessive

vibration

1. Loose parts or damaged

augers or impeller.

1. Tighten all fasteners. Replace damaged parts. If vibration

remains, contact an authorized service center/department.

Recoil starter

is hard to pull

1. Frozen recoil starter.

1. See “IF RECOIL STARTER HAS FROZEN”

in the Operation section of this manual.

Loss of traction 1. Drive belt is worn.

1. Check / replace drive belt.

2. Check / reinstall drive belt.

drive / slowing

of drive speed

2. Drive belt is off of pulley.

3. Friction drive wheel is worn. 3. Contact an authorized service center/department.

Loss of snow

discharge or

slowing of

1. Auger belt is off of pulley.

2. Auger belt is worn.

3. Clogged discharge chute.

1. Check / reinstall auger belt.

2. Check / replace auger belt.

3. Clean snow chute.

4. Remove debris or foreign object from augers / impeller.

snow discharge 4. Augers / impeller jammed.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

NO.

PART

NO.

DESCRIPTION

404929X428

404932X479

72270505

155377

AUGER HOUSING 27

SCRAPER BAR

CARRIAGE BOLT 5/16−18 X .625

NUT 5/16−18

3 (5x)

4 (5x)

01.07.002-A

KEY

NO.

PART

NO.

DESCRIPTION

01.07.018-A

420495X479

420496X479

AUGER 27 LH

AUGER 27 RH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

AUGER HOUSING / IMPELLER ASSEMBLY

(EXPLODED)

01.07.026-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

NO.

PART

NO.

DESCRIPTION

175321X479 IMPELLER

427148

188909

427146

175322

GEARBOX ASSEMBLY

BEARING

IMPELLER PULLEY

DISCHARGE BASE

178675X008 CORNER BRACKET

192199

405400

73800400

74780426

427942

163183

427145

427154

73900600

180355

194189

407760

427302

427345

407770

407762

174697

407763

407764

189282

407758

174683

427147

7836M

CLEAN OUT TOOL

TOOL CLIP

NUT 1/4-20

SCREW 1/4-20 X .625

NUT 5/16-18

SCREW 5/16-18 X .625

IMPELLER HUB

IMPELLER SLEEVE

NUT 3/8-16

CARRIAGE BOLT

SCREW 13-16 X .625

PLUG

GEARBOX COVER RH

GASKET

SEAL

BEARING

THRUST WASHER 1.00

WORM GEAR

AUGER SHAFT

SQUARE KEY

BEARING

THRUST WASHER

IMPELLER SHAFT

ROLL PIN

THRUST WASHER

THRUST BEARING

BEARING

174681

174684

407769

407768

407767

427317

192090

O-RING

SCREW 5/16-18 X .750

GEARBOX COVER LH

SHEAR BOLT

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

AUGER HOUSING / IMPELLER ASSEMBLY

KEY

NO.

PART

NO.

DESCRIPTION

420478

411939

179582

AUGER BEARING

BEARING PLUG

SCREW 5/16−18 X 1.00

01.07.024-B

KEY

NO.

PART

NO.

DESCRIPTION

174762X479

178777X479

72270506

751153

SKID PLATE LH

SKID PLATE RH

CARRIAGE BOLT 5/16−18 X .75

NUT 5/16−18

01.11.001-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

CONTROL PANEL / CHUTE

*14

*11

*13

KEY

NO.

PART

NO.

*12

DESCRIPTION

420315X428

178633X428

420673

CHUTE WELDMENT

DEFLECTOR WELDMENT

DEFLECTOR CONTROL ASSEMBLY

DEFLECTOR SEAL

420325

414280

128415

KNOB BLACK

POP RIVET

*10

*11

*12

*13

*14

17501010

430324

419822X004

179829

191730

72250505

751153

184505

420679

420672

SCREW 10-24 X .625

CHUTE SNOW SHIELD

SHIELD RETAINER STRAP

SHOULDER BOLT 1/4-20 X .375

NUT 1/4-20

CARRIAGE BOLT 3/8-16 X .625

NUT 5/16-18

DEFLECTOR SPRING

(SERVICE PART) DEFLECTOR CONTROL

(SERVICE PART) DEFLECTOR CABLE Black

01.09.015-A

NOTE:

1. ALL ITEMS INDICATED WITH AN * ARE PROVIDED IN THE BAG OF ITEMS SHIPPED LOOSE WITH PRODUCT.

2. ITEMS 15 AND 16 ARE SERVICE PART NUMBERS TO ALLOW PURCHASE OF INDIVIDUAL ITEMS IF NECES-

SARY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

CONTROL PANEL / CHUTE

KEY

NO.

PART

NO.

DESCRIPTION

428272

17501010

420678

405932

420675

428273

428310

LEVER/CABLE ROTATOR ASSEMBLY

SCREW 10-24 X .625

ROTATOR HEAD

ROTATOR PIVOT BRACKET

PULLEY PIVOT

CABLE ASSEMBLY ADJUSTABLE

CABLE ASSEMBLY HEAT SHIELD

01.09.010-B

NOTES:

1. ITEMS INDICATED WITH AN * ARE LISTED AS REFERENCE FOR SERVICE PARTS ONLY.

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

HANDLES

KEY

NO.

PART

NO.

419798X479

419799 X479 LOOP HANDLE RH

74780524

751153

DESCRIPTION

LOOP HANDLE LH

SCREW 5/16−18 X 1.50

NUT 5/16−18

01.08.004-B

KEY

NO.

PART

NO.

DESCRIPTION

419797X479

418313X479

428867

LOWER TUBE

PIVOT SUPPORT

BOLT 5/16-18 X .750

SCREW 3/8-16 X 1.00

17000616

01.05.004-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

HANDLES

01.08.002-F

KEY

NO.

PART

NO.

DESCRIPTION

412683X479

424517X479

424516X479

426917X008

426918X008

412677

CONTROL PANEL

CONTROL LEVER LH

CONTROL LEVER RH

TRACTION ROD ARM

IMPELLER ROD ARM

INTERLOCK BAIL

SPACER

421613

169675

17060410

414280

414281

178899

19131316

72120618

RETAINER

SCREW 1/4-20 X .62

KNOB BLACK

KNOB RED

HANDLE KNOB

WASHER 3/8

CARRIAGE BOLT 3/8-16 X 2.25

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

HANDLES

KEY

NO.

PART

NO.

DESCRIPTION

180480

405740

180445

187716

180447

178669

180926

72270505

155377

169675

IMPELLER ROD ASSEMBLY

TRACTION ROD ASSEMBLY

SHIFTER ROD TOP

SHIFTER ROD BOTTOM

SPRING SLEEVE

IMPELLER SPRING

TRACTION SPRING

CARRIAGE BOLT 5/16-18 X .75

NUT 5/16-18

RETAINER

01.12.001-E

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

HANDLES

KEY

NO.

PART

NO.

DESCRIPTION

429624

178668

180927

184471

175262

178770

183784

CONSOLE PANEL

HEADLIGHT BEZEL

FLOOD HEADLIGHT

SHOULDERSCREW10−24X.625

SCREW 10−24 X 1.25

WIRE HARNESS

BULB

01.10.027-A

KEY

NO.

PART

NO.

DESCRIPTION

412675X004

414572

178831

169675

17060410

421252X004

INTERLOCK SPRING

INTERLOCK CAM

TORSION SPRING

RETAINER

SCREW 1/4−20 X .625

INTERLOCK STOP

01.08.007-B

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

DRIVE

KEY

NO.

PART

NO.

DESCRIPTION

188226

179352

9465M1

402691

174697

179830

17490508

155443

189282

(assy of 1a,1b) AXLE ASSEMBLY

AXLE SHAFT

ROLL PIN 3/16

SPROCKET

THRUST WASHER

BEARING

BOLT 5/16−18 X .500

CLIK PIN

01.03.005-B

SQUARE KEY

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

DRIVE

42 EXPLODED

01.02.013-A

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

DRIVE

KEY

NO.

PART

NO.

KEY

NO.

PART

NO.

DESCRIPTION

179831

175344

178613

74760514

12000012

402187

401619

417234

401984X479

180135

402652

428288

184471

410877

413429X479

402689

414557

178828

402504X008

401820

198791

402393

17541008

402511

418894X479

132010

428867

RUBBER RING

BEARING

WHEEL HUB

SCREW 5/16-18-.875

RETAINER RING

SPROCKET SHAFT

CHAIN

SPROCKET WELDMENT

SHIFTER BRACKET

SPRING

PLATE PIVOT ROD

E-RING .375

SHOULDER SCREW

BOTTOM PAN

SPRING BRACKET

DRIVE PLATE ASSEMBLY

IDLER SPRING

PULLEY SHAFT

DRIVE PLATE

198875

SPEED SELECTOR

ASSEMBLY

SCREW 10-24 X .625

END PLATE

SCREW 5/16-18 X .50

WASHER

CONTROL ARM

CLEVIS PIN

SHIFTER PLATE

SHOULDER BOLT

SHIFTER BRACKET

NUT 1/4-20

CLUTCH PLATE

CLUTCH BRACKET

SHIFTER LINK

RETAINER

CONTROL SHAFT

CLUTCH ROD

RETAINER

SHIFTER YOKE

PIVOT ROD

17501010

402685X428

17490508

57079

405485

198580

403097X004

402881

403096X004

191730

402856X004

416717X004

187101

700279

427542

402568

169675

401732

402310

12000036

402878

751153

BEARING

PULLEY HALF

SCREW 10-24 X .50

SPACER BEARING

SWING PLATE

NUT 3/8-16

SCREW 5/16-18 X .750

RETAINER

RETURN SPRING

NUT 5/16-18

BEARING

NUT 5/16-18

408981

73930500

198176X479

RUBBER WHEEL PLATE

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

CHASSIS / ENGINE / PULLEYS

KEY

NO.

PART

NO.

DESCRIPTION

- -

428757

418694X428

150406

265cc POULAN PRO ENGINE

FRAME

BOLT 3/8-16

01.00.034-A

428867

SCREW 5/16-18 X .750

KEY

NO.

PART

NO.

DESCRIPTION

427928X428

ENGINE MOUNTING PLATE

01.01.005-A

KEY

NO.

PART

NO.

DESCRIPTION

428685

COVER ASSEMBLY

01.21.014-C

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

CHASSIS / ENGINE / PULLEYS

01.21.005-C

KEY

NO.

PART

NO.

KEY

NO.

PART

DESCRIPTION

NO.

DESCRIPTION

419888

427304

423723X479

180523

423990X479

426589

74780524

424297

751153

428867

427576

180522

IMPELLER BELT

TRACTION BELT

IDLER ARM BRACKET

IDLER PULLEY

IDLER BRACKET

NUT 5/16-18

SCREW 5/16-18 X 1.50

SHOULDER BOLT 5/16-18 X .50

NUT 5/16-18 NYLOCK

SCREW 5/16-18 X .625

TRACTION IDLER BRACKET

TRACTION PULLEY

59289

WASHER

NUT 5/16-18

73800500

74780520

851084

19132005

425934

SCREW 5/16-18 X 1.25

SCREW 3/8-24 X 1.375

WASHER

PULLEY ENG IMPELLER

PULLEY ENG TRACTION

SCREW 5/16-24 X 1.00

LOCKWASHER 5/16

BELT GUIDE

425933

74610516

10040500

155452

11050500

175331

LOCKWASHER 5/16

IDLER BUSHING

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

WHEELS

KEY

NO.

PART

NO.

DESCRIPTION

01.06.002-A

187833X421

187865X421

WHEEL ASSEMBLY LH

WHEEL ASSEMBLY RH

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

BAG OF PARTS

KEY

NO.

PART

NO.

DESCRIPTION

198563

169675

POWER CORD

RETAINER PIN

180684X008

184505

179829

WRENCH

REMOTE SPRING

SHOULDER BOLT 1/4-20

LOCKNUT 1/4-20

191730

72250505

751153

73800600

19131316

192090

CARRIAGE BOLT 5/16-18 X 5/8

LOCKNUT 5/16-18

LOCKNUT 3/8-16

WASHER 3/8

SHEAR BOLT 1/4-20 X 1-13/16

LOCKNUT 1/4-20

73800400

01.14.003-B

KEY

NO.

PART

NO.

DESCRIPTION

428498

SAFETY IGNITION KEY

01.14.010-A

2.56

01.14.012-A

KEY

PART

NO.

KEY

NO.

PART

NO.

DESCRIPTION

180445

187716

SHIFTER ROD TOP

SHIFTER ROD BOTTOM

72270505

155377

CARRIAGE BOLT 5/16-18 X .75

NUT 5/16-18

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

DECALS

KEY

NO.

PART

NO.

DESCRIPTION

181037

181035

181042

DECAL, DANGER

DECAL, DANGER, DEFLECTOR

DECAL, DANGER

NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm

IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

REPAIR PARTS SNOW THROWER - - MODEL NUMBER PP265E27(96198002801)

265^CCPOULAN PRO ENGINE-MODEL NUMBER 428757

KEY PART

NO. NO.

KEY PART

NO. NO.

DESCRIPTION

QTY.

DESCRIPTION

QTY.

429944

429945

429946

429947

429948

429949

429950

429951

429952

429953

429954

429955

429957

429959

429960

429962

429963

429964

429965

429966

429967

CRANK CASE

429968

429970

429971

429973

429974

429975

429976

429977

429979

429980

429982

FAN COOLING

CRANKSHAFT COMP

ROD ASSY ., CONNECTING

CAMSHAFT ASSY

PISTON

PULLEY,STARTER

STARTER ASSY.

CONTROL ASSY.

KNOB FUEL SWITCH

COVER, ENGINE

FUEL SWITCH

CRANK CASE COVER

HEAD COMP .,CYLINDER

COVER COMP ., HEAD

CARBURETOR

ARM, GOVERNOR

HOLDER,FUEL TANK

HOLDER,ELECTRIC STARTING

BOX

TANK COMP ., FUEL

REAR SOVER TANK

COVER, ENGINE

A HANGER

CAP ASSY.

SHROUD

GASKET , EX.PIPE

MUFFLER

AIR CLEANER

CHIOKE SET

KEY SWITCH

CHOKE LEVER

429984

429985

429986

429987

429988

429989

429990

429991

TUBE , BREATHER

SHROUD

PLUG , SPARK

STARTER,MOTOR

PLATE,WINDING

COIL ASSY .

COIL ASSY . , IGNITION

FLYWHEEL COMP

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY

1. FEDERAL EMISSION CONTROL WARRANTY STATEMENT

YOUR WARRANTY RIGHTS AND OBLIGATIONS

The United States Environmental Protection Agency(EPA), together with Husqvarna Consumer Outdoor

Products NA, Inc., are pleased to explain the emission control system warranty on your new model year

small off-road engines. In the United States (except California), new small off-road engines must be de-

signed, built and equipped to meet the Federal’s stringent anti-smog standards. Husqvarna Consumer

Outdoor Products NA, Inc. must warrant the emission control system on your small off-road engine for the

periods of time listed below provided there has been no abuse, neglect or improper maintenance of your

small off-road engine. Your emission control system may include parts such as the carburetor or fuel injection

system, the ignition system, and catalytic converter. Also included may be hoses, belts, connectors and other

emission related assemblies. Where a warrantable condition exists, Husqvarna Consumer Outdoor Products

NA, Inc. will repair your small off-road engine at no cost to you including diagnosis, parts and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 2009 and later small off-road engines are warranted for two years. If any emission related part on your

engine is defective, the part will be repaired or replaced by Husqvarna Consumer Outdoor Products NA, Inc.

OPERATOR’S WARRANTY RESPONSIBILITIES:

As the small off-road engine owner, you are responsible for the performance of the required maintenance

listed in your operator’s manual. Husqvarna Consumer Outdoor Products NA, Inc. recommends that you

retain all receipts covering maintenance on your small off-road engine, but Husqvarna Consumer Outdoor

Products NA, Inc. cannot deny warranty solely for the lack of receipts or for your failure to ensure the perfor-

mance of all scheduled maintenance.

As the small off-road engine owner, you should however be aware that Husqvarna Consumer Outdoor Prod-

ucts NA, Inc. may deny you warranty coverage if your small off-road engine or a part has failed due to abuse,

neglect, improper maintenance or unapproved modifications.

You are responsible for presenting your small off-road engine to a Husqvarna Consumer Outdoor Products

NA, Inc. distribution center as soon as a problem exists. The warranty repairs should be completed in a rea-

sonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact Husqvarna

Consumer Outdoor Products NA, Inc. at 1-800-849-1297

IMPORTANT NOTE: This warranty statement explains your rights and obligations under the Emission Con-

trol System Warranty (ECS Warranty), which is provided to you by Husqvarna Consumer Outdoor Products

NA, Inc. pursuant to EPA and federal law. See also the Husqvarna Consumer Outdoor Products NA, Inc.

Limited Warranties for additional product warranties, also provided to you by Husqvarna Consumer Outdoor

Products NA, Inc. The ECS Warranty applies only to the emission control system of your new engine. If there

is any conflict in terms between the ECS Warranty and the Husqvarna Consumer Outdoor Products NA, Inc.

Warranty, the ECS Warranty shall apply except in circumstances where the Husqvarna Consumer Outdoor

Products NA, Inc. Warranty may provide a longer warranty period. Both the ECS Warranty and the Husq-

varna Consumer Outdoor Products NA, Inc. Warranty describes important rights and obligations with respect

to your new engine.

Warranty service can be performed only by a Husqvarna Consumer Outdoor Products NA, Inc. Authorized

Warranty Service Facility. When requesting warranty service, evidence must be presented showing the date

of the sale to the original purchaser/owner. The purchaser/owner shall be responsible for any expenses or

other charges incurred for service calls and/or transportation of the product to/from the inspection or repair

facilities. The purchaser/owner shall also be responsible for any and/or all damages or losses incurred while

the engine is being transported/shipped for inspection or warranty repairs.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY

II. EMISSION CONTROL SYSTEM WARRANTY

Emission Control System Warranty (ECS Warranty) for 2009 and later model engines:

(a) Applicability: This warranty shall apply to 2009 and later model year engines. The ECS Warranty Period

shall begin on the date the new engine or equipment is purchased by/delivered to its original, end-use pur-

chaser/owner and shall continue for 24 consecutive months thereafter.

(b) General Emissions Warranty Coverage: Husqvarna Consumer Outdoor Products NA, Inc. warrants to the

original, end-use purchaser/owner of the new engine or equipment and to each subsequent purchaser/owner

that each of its engines is...

(1) Designed, built and equipped so as to conform with all applicable regulations adopted by the EPA pursu-

ant to their respective authority, and

(2) Free from defects in materials and workmanship, which, at any time during the ECS Warranty Period,

may cause a warranted emissions-related part to fail to be identical in all material respects to the part as

described in the engine manufacturer’s application for certification.The ECS Warranty only pertains to emis-

sions-related parts on your engine, as follows:

(1) Any warranted, emissions-related parts that are not scheduled for replacement as required maintenance

in the Operator’s Manual must be warranted for the ECS Warranty Period. If any such part fails during the

ECS Warranty Period, it shall be repaired or replaced by Husqvarna Consumer Outdoor Products NA, Inc.

according to Subsection (4) below. Any such part repaired or replaced under the ECS Warranty shall be war-

ranted for the remainder of the ECS Warranty Period.

(2) Any warranted emissions-related part that is scheduled only for regular inspection as specified in the

Operator’s Manual must be warranted for the ECS Warranty Period. A statement in such written instructions

to the effect of “repair or replace as necessary” shall not reduce the ECS Warranty Period. Any such part

repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS Warranty

Period.

(3) Any warranted emissions-related part that is scheduled for replacement as required maintenance in the

Operator’s Manual shall be warranted for the period of time prior to the first scheduled replacement point for

that part. If the part fails prior to the first scheduled replacement, the part shall be repaired or replaced by

Husqvarna Consumer Outdoor Products NA, Inc. according to Subsection (4) below. Any such emissions-

related part repaired or replaced under the ECS Warranty shall be warranted for the remainder of the ECS

Warranty Period prior to the first scheduled replacement point for such emissions-related part.

(4) Repair or replacement of any warranted, emissions-related part under this ECS Warranty shall be per-

formed at no charge to the owner at a Husqvarna Consumer Outdoor Products NA, Inc. Authorized Warranty

Service Facility.

(5) When the engine is inspected by a Husqvarna Consumer Outdoor Products NA, Inc. Authorized Warranty

Service Facility, the owner shall not be held responsible for diagnostic costs if the repair is deemed warrant-

able.

(6) Husqvarna Consumer Outdoor Products NA, Inc. shall be liable for damages to other original engine

components or approved modifications proximately caused by a failure under warranty of any emission-relat-

ed part covered by the ECS Warranty.

(7) Throughout the ECS Warranty Period, Husqvarna Consumer Outdoor Products NA, Inc. shall maintain a

supply of warranted emission-related parts sufficient to meet the expected demand for such emission-related

parts.

(8) Any Husqvarna Consumer Outdoor Products NA, Inc. authorized and approved emission-related replace-

ment part may be used in the performance of any ECS Warranty maintenance or repairs and will be provided

without charge to the purchaser/owner. Such use shall not reduce Husqvarna Consumer Outdoor Products

NA, Inc. ‘s ECS Warranty obligations.

Download from Www.Somanuals.com. All Manuals Search And Download.

WARRANTY

(9) Unapproved, add-on, modified, counterfeit and/or “grey market” parts may not be used to modify or repair

a Husqvarna Consumer Outdoor Products NA, Inc. engine. Such use voids this ECS Warranty and shall

be sufficient grounds for disallowing an ECS Warranty claim. Husqvarna Consumer Outdoor Products NA,

Inc. shall not be held liable hereunder for failures of any warranted parts of a Husqvarna Consumer Outdoor

Products NA, Inc. engine caused by the use of such an unapproved, add-on, modified, counterfeit and/or

“grey market” part.

EMISSION RELATED PARTS INCLUDE THE FOLLOWING: (New Phase III language inserted, but may not

be necessary to use.)

I. For exhaust emissions, emission-related components include any engine parts related to the following sys-

tems:

1. Air-induction system.

2. Fuel system.

3. Ignition system.

4. Exhaust gas recirculation systems.

II. The following parts are also considered emission-related components for exhaust emissions:

1. Aftertreatment devices.

2. Crankcase ventilation valves.

3. Sensors.

4. Electronic control units.

III. The following parts are considered emission-related components for evaporative emissions:

1. Fuel Tank.

2. Fuel Cap.

3. Fuel Line.

4. Fuel Line Fittings.

5. Clamps*.

6. Pressure Relief Valves*.

7. Control Valves*.

8. Control Solenoids*.

9. Electronic Controls*.

10. Vacuum Control Diaphragms*.

11. Control Cables*.

12. Control Linkages*.

13. Purge Valves.

14. Vapor Hoses.

15. Liquid/Vapor Separator.

16. Carbon Canister.

17. Canister Mounting Brackets.

18. Carburetor Purge Port Connector.

*As related to the evaporative emission control system.

IV. Emission-related components also include any other part whose only purpose is to reduce emissions or

whose failure will increase emissions without significantly degrading engine/equipment performance.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

HOP (The "Manufacturer") warrants to the original consumer purchaser that this product as manufactured is free from

defects in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer

purchaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part which

we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations and exclusions.

1. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the

purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by the

purchaser unless such return is requested by the manufacturer.

2. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date of

original purchase.

3. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained in

accordance with the instructions furnished. This Warranty does not apply to any product which has been subjected to

alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the product.

4. Exclusions: Excluded from this Warranty are normal wear, normal adjustments, standard hardware and normal

maintenance.

5. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.

Should you have any unanswered questions concerning this Warranty, please contact:

Poulan Pro

HOP Customer Service Dept.

1030 Stevens Creek Road

Augusta, GA 30907 USA

1-800-849-1297

giving the model number, serial number and date of purchase of your product and the name and address of the authorized

dealer from whom it was purchased.

THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED

WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WARRANTIES.

Some areas do not allow the limitation of consequential damages or limitations of how long an implied Warranty may last,

so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights, and you may have

other rights which vary from locale to locale.

This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Fan DTH 4 User Manual
Pelco Video Gaming Accessories C561M F User Manual
Pentax Digital Camera PC 550 User Manual
Philips Baby Monitor M2922A User Manual
Philips Cell Phone SE735 User Manual
Philips DVD Player MDV458 User Manual
Philips Projector LC4331 User Manual
Philips Speaker HTL5120 User Manual
Pioneer Car Stereo System DEH P4800MP User Manual
Planet Technology Network Card WL 8317 User Manual