Poulan Snow Blower 406281 User Manual

IMPORTANT MANUAL  
Do Not Throw Away  
OWNER'S MANUAL  
MODEL NUMBER:  
WARNING:  
Read the Owner's Manual and  
follow all Warnings and Safety  
Instructions. Failure to do so  
can result in serious injury.  
PP11H30ES  
SNOW THROWER  
406281 08.14.06 BY  
Printed in U.S.A.  
Always Wear Eye Protection During Operation  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6. Whencleaning,repairingorinspectingthesnowthrower,  
stoptheengineandmakecertainthecollector/impeller  
and all moving parts have stopped. Disconnect the  
spark plug wire and keep the wire away from the plug  
to prevent someone from accidentally starting the en-  
gine.  
16. Never touch a hot engine or muffler.  
Clearing a Clogged Discharge Chute  
Handcontactwiththerotatingimpellerinsidethedischarge  
chute is the most common cause of injury associated with  
snow throwers. Never use your hand to clean out the dis-  
charge chute. To clear the chute:  
7. Do not run the engine indoors, except when starting  
the engine and for transporting the snow thrower in or  
out of the building. Open the outside doors; exhaust  
fumes are dangerous.  
1. SHUT THE ENGINE OFF!  
2. Wait 10 seconds to be sure the impeller blades have  
stopped rotating.  
8. Exercise extreme caution when operating on slopes.  
3. Always use a clean-out tool, not your hands.  
9. Neveroperatethesnowthrowerwithoutproperguards,  
and other safety protective devices in place and work-  
ing.  
Maintenance and Storage  
1. Check shear bolts and other bolts at frequent intervals  
for proper tightness to be sure the equipment is in safe  
working condition.  
10. Never direct the discharge toward people or areas  
where property damage can occur. Keep children  
and others away.  
2. Never store the machine with fuel in the fuel tank  
inside a building where ignition sources are present  
such as hot water heaters, space heaters, or clothes  
dryers. Allow the engine to cool before storing in any  
enclosure.  
11. Do not overload the machine capacity by attempting  
to clear snow at too fast a rate.  
12. Never operate the machine at high transport speeds  
on slippery surfaces. Look behind and use care when  
operating in reverse.  
3. Always refer to operator’s manual for important details  
if the snow thrower is to be stored for an extended  
period.  
13. Disengage power to the collector/impeller when snow  
thrower is transported or not in use.  
14. Use only attachments and accessories approved by  
the manufacturer of the snow thrower (such as wheel  
weights, counterweights, or cabs).  
4. Maintain or replace safety and instruction labels, as  
necessary.  
5. Run the machine a few minutes after throwing snow  
to prevent freeze-up of the collector/impeller.  
15. Never operate the snow thrower without good visibility  
or light. Always be sure of your footing, and keep a firm  
hold on the handles. Walk; never run.  
CONGRATULATIONS on your purchase of a new snow  
thrower. Ithasbeendesigned,engineeredandmanufactured  
to give best possible dependability and performance.  
PRODUCT SPECIFICATIONS  
Gasoline Capacity 4.0 Quarts (4,54 Liters)  
and Type:  
Unleaded Regular only  
Should you experience any problem you cannot easily  
remedy, please contact your nearest authorized service  
center. We have competent, well-trained technicians and  
the proper tools to service or repair this unit.  
Oil Type  
(API SG–SL):  
SAE 5W-30 or 10W-30  
(0° to +40°F)  
SAE 0W-30 (below 0°F)  
Please read and retain this manual. The instructions will  
enable you to assemble and maintain your snow thrower  
properly. Always observe the “SAFETY RULES”.  
Oil Capacity:  
26 Ounces (0,74 Liters)  
Spark Plug  
Gap:  
Champion RJ19LM  
0.030" (0,072 mm)  
SERIAL NUMBER: ___________________________  
DATE OF PURCHASE: _______________________  
THEMODELANDSERIALNUMBERSWILLBEFOUND  
ONADECALATTACHEDTOTHEREAROFTHESNOW  
THROWER HOUSING.  
CUSTOMER RESPONSIBILITIES  
Read and observe the safety rules.  
Follow a regular schedule in maintaining, caring for  
and using your snow thrower.  
YOUSHOULDRECORDBOTHSERIALNUMBERAND  
DATE OF PURCHASE AND KEEP IN A SAFE PLACE  
FOR FUTURE REFERENCE.  
FollowtheinstructionsunderMaintenanceandStor-  
age” sections of this owner’s manual.  
TABLE OF CONTENTS  
SAFETY RULES ........................................................ 2-3  
MAINTENANCE SCHEDULE ..................................... 14  
SERVICE AND ADJUSTMENTS ........................... 16-18  
STORAGE................................................................... 18  
TROUBLESHOOTING................................................ 19  
REPAIR PARTS ..................................................... 20-31  
WARRANTY................................................................ 32  
PRODUCT SPECIFICATIONS...................................... 3  
CUSTOMER RESPONSIBILITIES................................ 3  
ASSEMBLY / PRE-OPERATION............................... 5-7  
OPERATION ............................................................ 8-13  
MAINTENANCE..................................................... 14-15  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS PACKED SEPARATELY IN CARTON  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
Read these instructions and this manual in its entirety  
SPEED  
CONTROL  
ROD  
before you attempt to assemble or operate your new  
snow thrower. Reading the entire manual will familiar-  
ize you with the unit, which will assist you in assembly,  
operation and maintenance of the product.  
PLASTIC TIE  
Your new snow thrower has been assembled at the factory  
with the exception of those parts left unassembled for ship-  
ping purposes. All parts such as nuts, washers, bolts, etc.,  
necessary to complete the assembly have been placed in  
the parts bag. To ensure safe and proper operation of your  
snow thrower, all parts and hardware you assemble must  
be tightened securely. Use the correct tools as necessary  
to ensure proper tightness.  
UPPER  
HANDLE  
HANDLE  
KNOB  
LOWER  
HANDLE  
REMOVE SNOW THROWER FROM CARTON  
1. Remove all accessible loose parts and parts boxes  
from carton.  
2. Cut down all four corners of carton and lay panels flat.  
3. Removethetwo(2)screwssecuringtheaugerhousing  
to the pallet.  
4. Removeallpackingmaterialsexceptplastictieholding  
speed control rod to lower handle.  
5. Remove the two (2) plastic ties securing the upper  
handle to the pallet.  
6. Remove snow thrower from carton and check carton  
thoroughly for additional loose parts.  
FIG. 1  
SPEED CONTROL ROD  
HOW TO SET UP YOUR SNOW THROWER  
TOOL BOX (See Fig. 10)  
RETAINER  
SPRING  
A toolbox is provided on your snow thrower. The toolbox is  
located on top of the belt cover. Store the extra shear bolts,  
nuts and multi-wrench provided in parts bag in the toolbox.  
NOTE: The multi-wrench may be used for assembly of the  
chuterotatorheadtosnowthrowerandmakingadjustments  
to the skid plates.  
UNFOLD UPPER HANDLE  
1. Raiseupperhandletotheoperatingpositionandtighten  
handle knobs securely.  
SPEED  
CONTROL  
BRACKET  
SPEED  
CONTROL  
LEVER  
INSTALL SPEED CONTROL ROD (See Figs. 1 and 2)  
1. Remove plastic tie securing rod to lower handle.  
FIG. 2  
2. Insert rod into speed control bracket and secure with  
retainer spring.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
INSTALL TRACTION DRIVE CONTROL ROD  
(See Figs. 3 and 4)  
The traction drive control rod has the long loop on the end  
of the spring as shown.  
INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)  
The auger control rod has the short loop on the end of the  
spring as shown.  
1. Slide rubber sleeve up rod and hook end of spring into  
control arm with loop opening up as shown.  
1. Slide rubber sleeve up rod and hook end of spring into  
eye of cable with loop opening down as shown.  
2. With top end of rod positioned under right side of  
control panel, push down on rod and insert end of rod  
into hole in auger control bracket. Secure with retainer  
spring.  
2. With top end of rod positioned under left side of control  
panel, pushroddownandinserttopendofrodintohole  
in drive control bracket. Secure with retainer spring.  
TRACTION DRIVE  
CONTROL ROD  
AUGER  
CONTROL  
ROD  
RUBBER  
SLEEVE  
RUBBER  
SLEEVE  
LOOP  
OPENING  
DOWN  
CONTROL  
ARM  
LOOP  
OPENING  
UP  
CABLE  
FIG. 3  
FIG. 5  
AUGER CONTROL ROD  
AUGER  
CONTROL  
LEVER  
TRACTION DRIVE  
CONTROL LEVER  
RETAINER  
SPRING  
RETAINER  
SPRING  
TRACTION  
DRIVE  
CONTROL  
ROD  
DRIVE  
CONTROL  
BRACKET  
AUGER  
CONTROL  
BRACKET  
FIG. 4  
FIG. 6  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
ASSEMBLY / PRE-OPERATION  
INSTALL DISCHARGE CHUTE / CHUTE ROTATOR  
HEAD (See Fig. 7)  
NOTE: The multi-wrench provided in your parts bag may  
be used to install the chute rotator head.  
SPRING  
1/4-20  
SHOULDER  
BOLT  
CHUTE  
DEFLECTOR  
HOOK  
1. Place discharge chute assembly on top of chute base  
with discharge opening toward front of snow thrower.  
BETWEEN  
HEX NUTS  
ON CHUTE  
ROTATER  
HEAD  
NYLON  
WASHER  
2. Positionchuterotatorheadoverchutebracket. Ifneces-  
sary,rotatechuteassemblytoalignsquareandpinonun-  
dersideofchuterotatorheadwithholesinchutebracket.  
1/4-20  
LOCKNUT  
5/16-18  
3. With chute rotator head and chute bracket aligned,  
position chute rotator head on pin and threaded stud  
of mounting bracket.  
CARRIAGE  
BOLT  
CABLE  
EYELET  
4. Install 3/8 washer and locknut on threaded stud and  
tighten securely.  
CHUTE  
ROTATOR  
HEAD  
REMOTE  
3/8 LOCKNUT  
3/8 WASHER  
CABLE  
BRACKET  
5/16-18  
LOCKNUT  
FIG. 8  
PIN  
THREADED  
STUD  
ROTATOR HEAD  
MOUNTING  
CHUTE  
ALIGN BEFORE  
BRACKET  
BRACKET TIGHTENING LOCKNUT  
FIG. 7  
CHUTE DEFLECTOR  
CONTROL LEVER  
INSTALL CHUTE DEFLECTOR REMOTE CONTROL  
(See Figs. 8 and 9)  
FIG. 9  
1. Install remote cable bracket to discharge chute with  
5/16-18 carriage bolt and 5/16-18 locknut as shown.  
Tighten securely.  
CHECK TIRE PRESSURE  
Thetiresonyoursnowthrowerwereoverinflatedatthefac-  
tory for shipping purposes. Correct and equal tire pressure  
is important for best snow throwing performance.  
2. Install remote cable eyelet to chute deflector with  
1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut  
as shown. Tighten securely.  
Reduce tire pressure to 14-17 PSI (19-24.5 N-m).  
3. Install spring hooks between hex nuts on chute rotater  
head and into hole in chute deflector as shown.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
KNOW YOUR SNOW THROWER  
READ THIS OWNER'S MANUALANDALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare  
the illustrations with your snow thrower to familiarize yourself with the location of various controls and adjustments. Save  
this manual for future reference.  
These symbols may appear on your snow thrower or in literature supplied with the product. Learn and understand  
their meaning.  
PRIMER  
DANGER  
OR WARNING  
READ AND FOLLOW ALL SAFETY INFORMATION  
AND INSTRUCTIONS BEFORE USE OF THIS PRODUCT.  
KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCE.  
FORWARD REVERSE  
IGNITION KEY.  
INSERT TO START  
AND RUN,  
PULL OUT TO STOP.  
DISENGAGED  
ENGAGED  
SNOW  
TRACTION  
DISCHARGE  
DRIVE CONTROL  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
AUGER  
CONTROL  
LEVER  
DISCHARGE CHUTE CONTROL LEVER  
SPARK  
PLUG  
ENGINE OIL CAP  
WITH DIPSTICK  
SAFETY  
IGNITION  
KEY  
DEFLECTOR REMOTE  
DRIVE SPEED  
CONTROL LEVER  
CONTROL LEVER  
GASOLINE  
FILLER  
CAP  
TRACTION  
DRIVE  
CONTROL  
LEVER  
CHUTE  
DEFLECTOR  
CHOKE  
CON-  
TROL  
OIL  
DRAIN  
PLUG  
LH TURN  
TRIGGER  
THROTTLE  
/ ENGINE  
CONTROL  
DISCHARGE  
CHUTE  
RECOIL  
POWER  
CORD  
PLUG  
(AUXILIARY)  
STARTER  
HANDLE  
LIGHT  
ELECTRIC  
START  
BUTTON  
FUEL  
SHUT-OFF  
VALVE  
CLEAN-  
OUT  
TOOL  
HANDLE  
KNOB  
PRIMER  
MUFFLER  
TOOLBOX  
NOTE: ITEMS ABOVE  
ARE SHOWN IN  
THEIR TYPICAL  
LOCATION ON THE  
ENGINE. ACTUAL  
LOCATION MAY VARY  
WITH THE ENGINE  
ON YOUR UNIT.  
FREEWHEEL  
CONTROL  
DRIFT CUTTER  
SKID PLATE  
AUGERS  
MEETS A.N.S.I. SAFETY REQUIREMENTS  
Oursnowthrowersconformtothestandardsof  
the American National Standards Institute.  
FIG. 10  
LH and RH turn triggers - used to steer the snow thrower.  
Toolbox - used to store spare shear bolts, locknuts and  
wrench.  
Throttle/engine control - used to select either FAST or  
SLOW engine speed and to STOP the engine.  
Safety ignition key - must be inserted for the engine to  
start and run. Remove when snow thrower is not in use.  
Traction drive control lever - used to engage power-pro-  
pelled forward or reverse motion of snow thrower.  
Electric start button - used for starting the engine.  
Recoil(auxiliary)starterhandle-usedforstartingengine.  
Drift cutter - used to cut through deep snowdrifts.  
Auger control lever - used to engage auger motion (throw  
snow).  
Discharge chute control lever - used to change the di-  
rection the snow is thrown.  
Primer - pumps additional fuel from the carburetor to the  
cylinder for use when starting a cold engine.  
Skid plate - used to adjust height of scraper bar from the  
ground.  
Freewheelcontroldisengagestransmissionforpushing  
the snowthrower with the engine off.  
Deflector remote control lever - used to change the  
distance the snow is thrown.  
Choke control - used for starting a cold engine.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
The operation of any snow thrower can result  
in foreign objects thrown into the eyes, which  
canresultinsevereeyedamage. Alwayswear  
safety glasses or eye shields while operating  
your snow thrower or performing any adjust-  
OFF  
FULL  
00155  
ments or repairs. We recommend standard safety glasses  
or a wide vision safety mask worn over spectacles.  
HOW TO USE YOUR SNOW THROWER  
Know how to operate all controls before adding fuel or  
attempting to start the engine.  
FIG. 13  
TO CONTROL SNOW DISCHARGE (See Fig. 14)  
STOPPING  
TRACTION DRIVE  
WARNING: Snow throwers have ex-  
posed rotating parts, which can cause  
severe injury from contact, or from ma-  
terial thrown from the discharge chute.  
Keep the area of operation clear of all  
persons, small children and pets at all  
times including startup.  
Release traction drive control lever to stop the forward  
or reverse movement of the snow thrower.  
AUGER  
Release the auger control lever to stop throwing snow.  
ENGINE  
1. Move throttle control to “STOP” position.  
Ifthedischargechuteoraugerbecomeclogged,  
shut-off engine and wait for all moving parts to  
stop.Usetheclean-outtool,NOTYOURHANDS,  
to unclog the chute and/or auger.  
2. Remove (do not turn) safety ignition key to prevent  
unauthorized use.  
NOTE: Never use choke to stop engine.  
TO USE FUEL SHUT-OFF VALVE (See Fig. 11)  
TheDIRECTIONinwhichsnowistobethrowniscontrolled  
by the discharge chute control lever.  
The fuel shut-off valve is located beneath the fuel tank on  
the engine. Always operate the snow thrower with the fuel  
shut-off valve in the OPEN position.  
To change the discharge chute position, press down-  
ward on discharge chute control lever and move lever  
left or right until chute is in desired position. Be sure  
lever springs back and locks into desired position.  
DISCHARGE CHUTE  
CONTROL LEVER  
OFF  
OPEN  
FIG. 11  
TO USE THROTTLE CONTROL (See Fig. 12)  
Thethrottlecontrolislocatedontheengine.Alwaysoperate  
the snow thrower with the engine at full throttle. Full throttle  
offers the best snow thrower performance.  
CHUTE DEFLECTOR  
REMOTE CONTROL LEVER  
FAST  
FIG. 14  
The DISTANCE that snow is thrown is controlled by the  
position of the chute deflector. Set the deflector low to  
throw snow a short distance; set the deflector higher to  
throw snow farther.  
Press downward on chute deflector control lever and  
moveleverforwardtolowerthedeflectoranddecrease  
the distance. Move lever back to raise the deflector  
and increase the distance. Be sure lever springs back  
and locks into desired position.  
SLOW  
FIG. 12  
TO THROW SNOW (See Fig. 15)  
TO USE CHOKE CONTROL (See Fig. 13)  
The auger rotation is controlled by the auger control lever  
located on the right side handle.  
The choke control is located on the engine. Use the choke  
control whenever you are starting a cold engine. Do not  
use to start a warm engine.  
Squeeze auger control lever to handle to engage the  
auger and throw snow.  
To engage choke, turn knob clockwise. Slowly turn  
knob counterclockwise to disengage.  
Release the auger control lever to stop throwing snow.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
Slower speeds are for heavier snow and faster speeds  
AUGER  
CONTROL  
LEVER  
are for light snow and transporting the snow thrower. It  
is recommended that you use a slower speed until you  
are familiar with the operation of the snow thrower.  
NOTE: When both traction drive and auger control levers  
are engaged, the traction drive control lever will lock the  
auger control lever in the engaged position. This will allow  
you to release your right hand from the handle and adjust  
the discharge chute direction without interrupting the snow  
throwing process.  
FIG. 15  
USING THE CLEAN-OUT TOOL (See Fig. 16)  
In certain snow conditions, the discharge chute may be-  
come clogged with ice and snow. Use the clean-out tool to  
dislodge this blockage.  
TRACTION DRIVE  
CONTROL LEVER  
When cleaning, repairing, or inspecting,  
make certain all controls are disengaged and  
the auger/impeller and all moving parts have  
stopped. Disconnect the spark plug wire and  
keep the wire away from the spark plug to pre-  
vent accidental starting.  
Releasetheaugercontrolleverandshutofftheengine.  
DRIVE SPEED  
CONTROL LEVER  
Removetheclean-outtoolfromit'smountingclip. Grasp  
the tool firmly by the handle and push and twist the tool  
into the discharge chute to dislodge the blockage.  
FIG. 17  
POWER STEERING OPERATION (See Fig. 18)  
Afterthepackedsnowhasbeendislodged,returntheclean-  
out tool to it's mounting clip by pushing it into the clip.  
Steeringtriggersareusedtoassistinsteeringyoursnowthrow-  
er.Thetriggersarelocatedontheundersideofeachhandle.  
Whenatriggerissqueezed,itdisengagesthedrivewheelon  
thatsideofsnowthrowerandallowsittoturninthatdirection.  
Makesurethedischargechuteispointedinasafedirec-  
tion(novehicles,buildings,people,orotherobjectsare  
inthedirectionofdischarge)beforerestartingtheengine.  
To turn left – squeeze left side trigger.  
To turn right – squeeze right side trigger.  
Restart the engine, then squeeze the auger control  
lever to the handle to clear snow from the auger hous-  
ing and the discharge chute.  
LH TURN  
TRIGGER  
RH TURN  
TRIGGER  
DISCHARGE CHUTE  
CLEAN-OUT  
TOOL  
MOUNTING CLIP  
FIG. 16  
FIG. 18  
TO ADJUST SKID PLATES (See Fig. 19)  
NOTE:Thewrenchprovidedinyourpartsbagmaybeused  
TO MOVE FORWARD AND BACKWARD (See Fig. 17)  
to adjust the skid plates.  
SELF-PROPELLING, forward and reverse movement of  
the snow thrower, is controlled by the traction drive control  
lever located on the left side handle.  
Skid plates are located on each side of the auger housing  
and adjust the clearance between the scraper bar and the  
ground surface. Adjust skid plates evenly to proper height  
for current surface conditions. For removal of snow in  
normal conditions, such as a paved driveway or sidewalk,  
place skid plates in the highest position (lowest scraper  
clearance) to give a 1/8" clearance between the scraper  
bar and the ground. Use a middle position if the surface  
to be cleared is uneven.  
Squeezetractiondrivecontrollevertohandletoengage  
the drive system.  
Release traction drive control lever to stop the forward  
or reverse movement of the snow thrower.  
SPEED and DIRECTION are controlled by the drive speed  
control lever.  
NOTE: It is not recommended to operate the snow thrower  
overgravelorrockysurfaces.Objectssuchasgravel,rocks  
or other debris, can easily be picked up and thrown by the  
impeller, which can cause serious personal injury, property  
damage or damage to the snow thrower.  
Press downward on the speed control lever and move  
lever to desired position BEFORE engaging the trac-  
tion drive control lever. Be sure lever springs back and  
locks into desired position.  
CAUTION: Do not move speed control lever  
when traction drive control lever is engaged.  
Damage to the snow thrower can result.  
If snow thrower must be operated over gravel surface,  
use extra caution and be sure skid plates are adjusted  
to lowest (highest scraper clearance) position.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
1. Shut off engine and wait for all moving parts to stop.  
BEFORE STARTING THE ENGINE  
2. Adjust skid plates by loosening the rear 1/2" hex nut  
only,thenmovingskidplatetodesiredposition.Besure  
both plates are adjusted evenly. Tighten securely.  
CHECK ENGINE OIL LEVEL (See Fig. 22)  
The engine on your snow thrower has been shipped, from  
the factory, already filled with oil.  
1. Check engine oil with snow thrower on level ground.  
HIGH POSITION  
(LOW GROUND  
CLEARANCE)  
2. Remove oil fill cap/dipstick and wipe clean, reinsert  
the dipstick and screw tight, wait for a few seconds,  
remove and read oil level. If necessary, add oil until  
“FULL” mark on dipstick is reached. Do not overfill.  
AUGER  
HOUSING  
To change engine oil, see “TO CHANGE ENGINE OIL”  
in the Maintenance section of this manual.  
SKID PLATE  
ADD GASOLINE (See Fig. 22)  
1/2" HEX NUT  
Fill fuel tank to bottom of tank filler neck. Do not over-  
fill. Use fresh, clean, regular unleaded gasoline with  
a minimum of 87 octane. Do not mix oil with gasoline.  
Purchase fuel in quantities that can be used within 30  
days to assure fuel freshness.  
LOW POSITION (HIGH GROUND CLEARANCE)  
FIG. 19  
SCRAPER BAR  
The scraper bar is not adjustable, but is reversible. After  
considerable use it may become worn. When it has worn  
almost to the edge of the housing, it can be reversed,  
providing additional service before requiring replacement.  
Replace a damaged or worn scraper bar.  
WARNING: Wipe off any spilled oil or  
fuel. Do not store, spill or use gasoline  
near an open flame.  
CAUTION: Alcohol blended fuels (called  
gasohol or using ethanol or methanol) can at-  
tract moisture which leads to separation and  
formation of acids during storage. Acidic gas  
can damage the fuel system of an engine while  
in storage. To avoid engine problems, the fuel  
system should be emptied before storage of  
30 days or longer. Drain the gas tank, start  
the engine and let it run until the fuel lines  
and carburetor are empty. Use fresh fuel next  
season. SeeStorageInstructionsforadditional  
information. Never use engine or carburetor  
cleaner products in the fuel tank or permanent  
damage may occur.  
TO USE DRIFT CUTTERS (See Fig. 20)  
Use the drift cutters to cut through deep snowdrifts that are  
higher than the front of the snow thrower.  
Loosen upper adjustment nut enough to allow drift  
cutter to be raised to highest position and tighten nut  
securely. Repeat for opposite side of snow thrower.  
When not using drift cutters, loosen adjustment nut,  
lower to storage position and tighten nut securely.  
AUGER  
HOUSING  
CHOKE  
CONTROL  
THROTTLE PRIMER ENGINE OIL  
FILL CAP /  
STORAGE  
POSITION  
DRIFT  
CUTTER  
DIPSTICK  
SAFETY  
IGNITION  
KEY  
ADJUST-  
MENT NUT  
FIG. 20  
TO TRANSPORT (See Fig. 21)  
When pushing or towing your snowthrower, be sure to  
disengage transmission by placing freewheel control into  
FREEWHEELposition. Freewheel control is located at the  
rear of snowthrower.  
GASOLINE  
FILLER CAP  
FUEL SHUT-  
OFF VALVE  
Pull freewheel control out to FREEWHEEL position.  
To reengage transmission, push control back in.  
RECOIL  
STARTER  
HANDLE  
STARTER BUTTON  
POWER CORD PLUG  
NOTE: ALL ITEMS ARE SHOWN IN THEIR TYPICAL LOCATION.  
ACTUAL LOCATION MAY VARY WITH ENGINE ON YOUR UNIT.  
FIG. 22  
TO START ENGINE  
Be sure fuel shut-off valve is in the OPEN position.  
Your snow thrower engine is equipped with both a 120 Volt  
A.C. electric starter and a recoil starter. The electric starter  
is equipped with a three-wire power cord and plug and is  
designed to operate on 120 Volt A.C. household current.  
FREEWHEEL POSITION  
TRANSMISSION ENGAGED  
FIG. 21  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION  
BEFORE STOPPING  
Be sure your house is a 120 Volt A.C. three-wire  
grounded system. If you are uncertain, consult a  
licensed electrician.  
Run the engine for a few minutes to help dry off any mois-  
ture on the engine.  
Toavoidpossiblefreeze-upofthestarter,proceedasfollows:  
WARNING: Do not use the electric  
starter if your house is not a 120 Volt  
A.C. three-wire grounded system. Se-  
riouspersonalinjuryordamagetoyour  
snow thrower could result.  
ELECTRIC STARTER  
1. Connect the power cord to the engine.  
2. Plug the other end of the power cord into a three-hole  
grounded 120 Volt A.C. receptacle.  
3. While the engine is running, push starter button and  
spin the starter for several seconds.  
COLD START - ELECTRIC STARTER  
1. Insert safety ignition key (packed separately in parts  
bag)intoignitionslotuntilitclicks. DONOTturnthekey.  
Keep the extra safety ignition key in a safe place.  
NOTE: The unusual sound made while starter is spinning  
will not harm the engine or starter.  
4. Disconnect the power cord from the receptacle first,  
then from the engine.  
2. Place throttle control in FAST position.  
3. Rotate choke control to FULL position.  
4. Connect the power cord to the engine.  
RECOIL STARTER  
1. Whiletheengineisrunning,pulltherecoilstarterhandle  
5. Plug the other end of the power cord into a three-hole  
grounded 120 Volt A.C. receptacle.  
with rapid, full arm strokes three or four times.  
NOTE: The unusual sound made while pulling the recoil  
starter handle will not harm the engine or starter.  
6. Push the primer three (3) times.  
7. Push starter button until engine starts.  
IF RECOIL STARTER HAS FROZEN  
If the recoil starter has frozen and will not turn the engine,  
proceed as follows:  
IMPORTANT: Do not crank engine more than five con-  
tinuous seconds between each time you try to start. Wait  
5 to 10 seconds between each attempt.  
1. Grasp the recoil starter handle and slowly pull as much  
rope out of the starter as possible.  
8. When the engine starts, release the starter button and  
slowly move the choke control to the “OFF” position.  
2. Release the recoil starter handle and let it snap back  
against the starter.  
9. Disconnect the power cord from the receptacle first,  
then from the engine.  
If the engine still fails to start, repeat the above steps or  
use the electric starter.  
Allow the engine to warm up for a few minutes. Engine will  
not develop full power until it has reached normal operat-  
ing temperature.  
SNOW THROWING TIPS  
Always operate the snow thrower with the engine at  
full throttle. Full throttle offers the best performance.  
Goslowerindeep,freezingorheavywetsnow.Usethe  
drive speed control, NOT the throttle, to adjust speed.  
It is easier and more efficient to remove snow imme-  
diately after it falls.  
The best time to remove snow is the early morning. At  
this time the snow is usually dry and has not been ex-  
posed to the direct sun and warming temperatures.  
WARM START - ELECTRIC STARTER  
Follow the steps above, keeping the choke control in the  
OFF position.  
COLD START - RECOIL STARTER  
1. Insert safety ignition key (packed separately in parts  
bag)intoignitionslotuntilitclicks. DONOTturnthekey.  
Keep the extra safety ignition key in a safe place.  
2. Place throttle control in FAST position.  
3. Rotate choke control to FULL position.  
Slightly overlap each successive path to ensure all  
snow will be removed.  
4. Push the primer four (4) times if the temperature is  
below 15°F, or two (2) times if temperature is between  
15° and 50°F. If temperature is above 50°F, priming is  
not necessary.  
Throw snow downwind whenever possible.  
Adjust the skid plates to proper height for current snow  
conditions. See “TO ADJUST SKID PLATES” in this  
section of this manual.  
NOTE: Overprimingmaycauseooding,preventingtheen-  
ginefromstarting.Ifyoudooodtheengine,waitafewmin-  
utesbeforeattemptingtostartandDONOTpushtheprimer.  
Forextremelyheavysnow,reducethewidthofsnowre-  
movalbyoverlappingpreviouspathandmovingslowly.  
Keep engine clean and clear of snow during use. This  
will help air flow and extend engine life.  
Aftersnow-throwingiscompleted,allowenginetorunfor  
a few minutes to melt snow and ice off the engine.  
Clean the entire snow thrower thoroughly after each  
use and wipe dry so it is ready for next use.  
5. Pull recoil starter handle quickly. Do not allow starter  
rope to snap back.  
6. When the engine starts, release the recoil starter  
handle and slowly move the choke control to the OFF  
position.  
Allow the engine to warm up for a few minutes. Engine will  
not develop full power until it has reached normal operating  
temperature.  
WARNING: Do not operate snow  
throwerifweatherconditionsimpairvis-  
ibility. Throwing snow during a heavy,  
windysnowstormcanblindyouandbe  
hazardous to the safe operation of the  
snow thrower.  
WARM START - RECOIL STARTER  
Follow the steps above, keeping the choke in the OFF  
position. DO NOT push the primer.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
GENERAL RECOMMENDATIONS  
LUBRICATION CHART  
Thewarrantyonthissnowthrowerdoesnotcoveritemsthat  
have been subjected to operator abuse or negligence. To  
receivefullvaluefromthewarranty,operatormustmaintain  
snow thrower as instructed in this manual. Some adjust-  
mentswillneedtobemadeperiodicallytoproperlymaintain  
your snow thrower. All adjustments in the Service and  
Adjustments section of this manual should be checked at  
least once each season.  
SAE 5W-30 Motor Oil  
See “ENGINE” in  
Maintenance section  
General  
Purpose  
Grease  
Once a year, you should replace the spark plug and  
check belts for wear. A new spark plug will help your  
engine run better and last longer.  
Follow the maintenance schedule in this manual.  
NOTE: Use only Original Equipment Manufacturer (OEM)  
parts to service this unit. Failure to do so can cause the unit  
to malfunction and pose a risk of injury to the operator.  
Pivot  
points  
BEFORE EACH USE  
1. Check engine oil level.  
2. Check for loose fasteners.  
3. Checkcontrolstobesuretheyarefunctioningproperly.  
LUBRICATION  
Keep your snow thrower well lubricated  
(See “LUBRICATION CHART”).  
Engine  
oil  
Auger  
grease fittings  
SNOW THROWER  
Always observe the safety rules when performing any  
maintenance.  
V-BELTS  
Check V-belts for deterioration and wear after every 50  
hours of operation and replace if necessary. The belts  
are not adjustable. Replace belts if they begin to slip from  
wear. (See “TO REMOVE BELT COVER” in the Service  
and Adjustments section of this manual).  
TIRES  
Maintain proper air pressure in both tires (14–17 P.S.I.  
/ 19-24.5 N-m).  
Keeptiresfreeofgasolineandoil,whichcanharmrubber.  
TheV-beltsonyoursnowthrowerareofspecialconstruction  
andshouldbereplacedbyoriginalequipmentmanufacturer  
(OEM)beltsavailablefromyournearestdealer.Usingother  
than OEM belts can cause personal injury or damage to  
the snow thrower.  
NOTE: To seal tire punctures and prevent flat tires due to  
slow leaks, tire sealant may be purchased from your local  
parts dealer. Tire sealant also prevents tire dry rot and  
corrosion.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
AUGER GEAR CASE  
Oil will drain more freely when warm.  
Catch oil in a suitable container.  
The gear case was filled with lubricant to the proper  
level at the factory. The only time the lubricant needs  
attention is if service has been performed on the gear  
case.  
NOTE: The left side wheel may be removed from snow  
thrower for easier access to the oil drain plug and place-  
ment of a suitable container. The unit tilted, resting on the  
frame with the left wheel removed, will help drain any oil  
trapped inside the engine. (See “TO REMOVE WHEELS”  
in the Service and Adjustments section of this manual).  
If lubricant is required, use only Ronex ED #1  
grease.  
TRACTION DRIVE SYSTEM  
1. Disconnect spark plug wire from spark plug and place  
wire where it cannot come in contact with plug.  
DO NOT lubricate the drive components inside the snow  
thrower. The sprockets, hex shafts, drive disc and friction  
wheel require no lubrication. The bearings and bushings  
are lifetime lubricated and require no maintenance.  
2. Clean area around drain plug.  
3. Remove drain plug and drain oil in a suitable container.  
4. Install drain plug and tighten securely.  
CAUTION:Anylubricatingoftheabovecompo-  
nents can cause contamination of the friction  
wheel and damage to the drive system of your  
snow thrower.  
5. Wipe off any spilled oil from snow thrower and engine.  
6. Install left wheel (if removed for draining oil). Be sure to  
install klick pin into proper hole in wheel axle (See “TO  
REMOVE WHEELS” in the Service and Adjustments  
section of this manual).  
ENGINE  
See engine manual.  
7. Remove oil fill cap/dipstick. Be careful not to allow dirt  
to enter the engine.  
LUBRICATION  
8. Refill engine with oil through oil dipstick tube. Pour  
slowly. Do not overfill. For approximate capacity see  
“PRODUCTSPECIFICATIONSsectionofthismanual.  
Use only high quality detergent oil rated with API service  
classification SG–SL. Select the oil's SAE viscosity grade  
according to your expected operating temperature.  
9. Use gauge on oil fill cap/dipstick for checking level. Be  
sure dipstick cap is tightened securely for accurate  
reading. Keep oil at “FULL” line on dipstick.  
10. Wipe off any spilled oil.  
MUFFLER  
Inspect and replace corroded muffler as it could create a  
fire hazard and/or damage.  
SPARK PLUG  
Replacesparkplugatthebeginningofeachseasonorafter  
every100hoursofoperation,whicheveroccursrst. Spark  
plug type and gap setting are shown in the “PRODUCT  
SPECIFICATIONS” section of this manual.  
NOTE: Although multi-viscosity oils (5W30, 10W30 etc.)  
improve starting in cold weather, these multi-viscosity oils  
will result in increased oil consumption when used above  
32°F. Check your engine oil level more frequently to avoid  
possible engine damage from running low on oil.  
CLEANING  
IMPORTANT: For best performance, keep snow thrower  
housing free of any dirt or trash. Clean the outside of your  
snow thrower after each use.  
Changetheoilafterevery25hoursofoperationoratleastonce  
ayearifthesnowthrowerisnotusedfor25hoursinoneyear.  
Checkthecrankcaseoillevelbeforestartingtheengineand  
after each five (5) hours of continuous use. Tighten oil fill  
cap / dipstick securely each time you check the oil level.  
WARNING: Disconnectsparkplugwire  
fromsparkplugandplacewirewhereit  
cannot come in contact with plug.  
TO CHANGE ENGINE OIL  
Keepnishedsurfaces/wheelsfreeofgasoline,oil,etc.  
Determine temperature range anticipated before next oil  
change.AlloilmustmeetAPIserviceclassificationSG–SL.  
We do not recommend using a garden hose to clean  
yoursnowthrowerunlesstheelectricalsystem,muffler  
and carburetor are covered to keep water out. Water  
in engine can result in shortened engine life.  
Be sure snow thrower is on level surface.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
WARNING: To avoid serious injury, before performing any service or adjustments:  
1. Be sure throttle is in STOP position.  
2. Remove safety ignition key.  
3. Make sure the augers and all moving parts have completely stopped.  
4. Disconnect spark plug wire from spark plug and place wire where it cannot contact plug.  
SNOW THROWER  
TO ADJUST SNOW THROWER HEIGHT  
See “TO ADJUST SKID PLATES” and “SCRAPER BAR”  
in the Operation section of this manual.  
CAUTION: Do not substitute. Use only original  
equipment capscrew/shear bolts as supplied  
with your snow thrower.  
4. Connect spark plug wire to spark plug.  
CHUTE DEFLECTOR  
1/4-20  
LOCKNUT  
1/4-20 x 1-5/8  
CAPSCREW /  
SHEAR BOLT  
1/4-20 x 2  
SHOULDER /  
SHEAR BOLT  
The chute deflector, attached to the top of the discharge  
chute, is provided to direct discharging snow away from  
the operator. If the deflector becomes damaged, it should  
be replaced.  
IMPELLER HUB  
SPACER  
IMPELLER  
SHAFT  
WARNING: To avoid serious injury,  
never operate your snow thrower with  
the deflector removed or damaged.  
Tochangedirectionand/ordistancesnowisdischarged,  
see “TO CONTROL SNOW DISCHARGE” in the Op-  
eration section of this manual.  
AUGER  
HUB  
SHEAR BOLTS (See Fig. 23)  
AUGER SHEAR BOLTS  
Both right and left-hand augers are secured to the auger  
shaft with a shoulder/shear bolt and hex nut. Should a for-  
eign object or ice become lodged in the augers, the shear  
bolts are designed to break, preventing damage to any  
other components. If one or both augers do not turn when  
auger control lever is engaged, check to see if one or both  
of the bolts have sheared. To replace the shear bolts:  
1/4-20  
LOCKNUT  
AUGER HUB  
FIG. 23  
AUGER SHAFT  
TO REMOVE BELT COVER (See Fig. 24)  
1. Remove the two screws securing belt cover to frame.  
2. Remove belt cover.  
1. Disengage all controls and move throttle control to  
STOP position. Wait for all moving parts to stop.  
Replace belt cover by installing cover and screws and  
tighten securely.  
2. Disconnect spark plug wire from spark plug and place  
wire where it cannot come in contact with plug.  
3. Alignholeinaugerhubwithholeinaugershaftandinstall  
anew1/4-20x2"shoulder/shearboltandspacer.Install  
1/4-20 lock nut and tighten securely.  
CAUTION: Do not substitute. Use only original  
equipment shear bolts as supplied with your  
snow thrower.  
4. Connect spark plug wire to spark plug.  
IMPELLER SHEAR BOLTS  
FRAME  
BELT COVER  
FIG. 24  
SCREWS  
The impeller is secured to the impeller shaft with two (2)  
capscrew/shearboltsandhexnuts. Shouldaforeignobject  
or ice become lodged in the impeller, the capscrews are  
designed to break, preventing damage to any other com-  
ponents. If impeller does not turn when auger control lever  
is engaged, check to see if the capscrews have sheared.  
To replace the capscrew/shear bolts:  
TO REPLACE BELTS (See Fig. 25)  
The auger and traction drive belts are not adjustable. If the  
belts are damaged or begin to slip from wear, they should  
be replaced. It is recommended that the belt(s) be replaced  
by a qualified service center.  
1. Disengage all controls and move throttle control to  
STOP position. Wait for all moving parts to stop.  
NOTE: It is recommended that both the auger and traction  
drive belt be replaced at the same time.  
2. Disconnect spark plug wire from spark plug and place  
wire where it cannot come in contact with plug.  
TheV-beltsonyoursnowthrowerareofspecialconstruction  
andshouldbereplacedbyoriginalequipmentmanufacturer  
(OEM)beltsavailablefromyournearestdealer.Usingother  
than OEM belts can cause personal injury or damage to  
16 the snow thrower.  
3. Align holes in impeller hub with holes in impeller shaft  
and install two (2) new 1/4-20 x 1-5/8" capscrew/shear  
bolts. Install 1/4-20 locknuts and tighten securely.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
12. Install the two (2) hex bolts and lock washers and  
WARNING: Belt replacement requires  
separation of the snow thrower. While  
separating the auger housing from the  
frame assembly, it is important that an  
assistantstandintheoperatingposition  
andholdthesnowthrowerhandles.Se-  
rious personal injury and/or damage to  
theunitcouldoccurifthesnowthrower  
should fall during the belt changing  
process.  
tighten securely.  
13. INSTALLENGINEPULLEY-Placebeltinpulleygroove  
and slide pulley on crankshaft. Install flat washer, lock-  
washer and bolt and tighten securely (30-35 ft. lbs.  
torque). Make sure belt is inside belt keeper.  
14. INSTALL BELT COVER and two (2) screws. Tighten  
securely.  
15. INSTALL DISCHARGE CHUTE – See “INSTALL DIS-  
CHARGE CHUTE / CHUTE ROTATER HEAD” in the  
Assembly / Pre-Operation section of this manual.  
FRAME  
ASSEMBLY  
AUGER  
HOUSING  
BELT KEEPER  
TRACTION DRIVE BELT  
ENGINE  
FLAT WASHER  
PULLEY  
HANDLES  
LOCKWASHER  
BOLT  
1. REMOVEGASOLINEFROMFUELTANK-Draingaso-  
line from fuel tank into a suitable container, outdoors,  
away from fire or flame. Wipe up any spilled gasoline.  
AUGER  
BELT  
IDLER ARM  
SQUARE  
HOLE  
2. REMOVE DISCHARGE CHUTE - Loosen locknut  
securing chute rotator head to mounting bracket only  
enough to allow chute rotator head to be raised and  
discharge chute to be removed from snow thrower.  
CLUTCHING  
IDLER ARM  
BRACKET  
3. REMOVE BELT COVER - See “TO REMOVE BELT  
COVER” in this section of this manual.  
AUGER PULLEY  
BOLT  
LOCK  
WASHER  
4. REMOVEENGINEPULLEY-Removebolt,lockwasher  
and flat washer securing pulley to engine crankshaft.  
Remove outside (auger) pulley only from crankshaft.  
5. SEPARATE SNOW THROWER - With your assistant  
standing in the operating position holding the handles,  
remove the two (2) bolts and lock washers holding  
auger housing and frame together.  
AUGER  
WARNING: As the last bolt is removed,  
have your assistant carefully lower the  
handles down to the ground.  
FRAME  
HOUSING  
FIG. 25  
TO REMOVE WHEELS (See Fig. 26)  
Remove the klik pin and remove wheel from axle.  
6. REMOVE AUGER BELT from around pulley.  
7. RELIEVETENSIONONTRACTIONDRIVEBELTIDLER  
and remove traction drive belt from around pulleys.  
IMPORTANT:Wheninstallingwheel,besuretousetheaxle  
hole closest to the end of the shaft – do not use the hole  
in the wheel hub (if equipped). Inner hole in axle and hole  
in wheel hub are not used for your model snow thrower.  
HINT: Insert a 3/8" drive ratchet (in the “ON” position) into  
the square hole in idler arm and rotate ratchet clockwise  
to relieve tension.  
NOTE: To seal punctures or prevent flat tires due to slow  
leaks, tire sealant may be purchased from your local parts  
dealer. Tire sealant also prevents tire dry rot and corrosion.  
8. With tension relieved on idler, install new traction drive  
belt around pulleys and inside belt keepers.  
9. Placeaugerbeltaroundandinsidethegrooveofauger  
pulley only.  
KLIK PIN (INSTALL  
IN OUTER HOLE  
OF AXLE ONLY)  
OUTER HOLE  
10. While your assistant slowly raises handles to rejoin  
the auger housing and frame assembly, pull up on the  
auger belt and squeeze sides together above pulley  
so belt is fully seated in groove of pulley.  
11. Bring snow thrower completely together and check  
carefully for proper routing of belts. If auger belt has  
becomedislodgedfromthepulley(bycatchingtheidler  
arm bracket while bringing snow thrower together),  
separate the snow thrower and repeat step 10. Belt  
must be fully seated in pulley groove when bringing  
the snow thrower together.  
AXLE  
WHEEL  
WHEEL HUB  
17  
FIG. 26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SERVICE AND ADJUSTMENTS  
ENGINE SPEED  
ENGINE  
See engine manual.  
Nevertamperwiththeenginegovernor, whichisfactoryset  
for proper engine speed. Overspeeding the engine above  
the factory high speed setting can be dangerous and will  
void the warranty. If you think the engine-governed high  
speed needs adjusting, contact a qualified service center,  
which has proper equipment and experience to make any  
necessary adjustments.  
CARBURETOR  
Your carburetor is not adjustable. Engine performance  
should not be affected at altitudes up to 7,000 feet (2,134  
meters). If your engine does not operate properly due to  
suspected carburetor problems, take your snow thrower to  
a qualified service center.  
STORAGE  
Immediately prepare your unit for storage at the end of the  
season or if the unit will not be used for 30 days or more.  
Empty the fuel tank by starting the engine and letting  
it run until the fuel lines and carburetor are empty.  
Never use engine or carburetor cleaner products in the  
fuel tank or permanent damage may occur.  
WARNING: Never store the snow  
throwerwithgasolineinthetankinside  
a building where fumes may reach an  
open flame, spark or pilot light as on a  
furnace, water heater, clothes dryer or  
gasappliance. Allowtheenginetocool  
before storing in any enclosure.  
Use fresh fuel next season.  
NOTE: Fuel stabilizer is an acceptable alternative in min-  
imizing the formation of fuel gum deposits during storage.  
Add stabilizer to gasoline in fuel tank or storage container.  
Always follow the mix ratio found on stabilizer container.  
Run engine at least 10 minutes after adding stabilizer to  
allow the stabilizer to reach the carburetor. Do not drain the  
gas tank and carburetor if using fuel stabilizer.  
SNOW THROWER  
When snow thrower is to be stored for a period of time,  
clean it thoroughly, remove all dirt, grease, leaves, etc.  
Store in a clean, dry area.  
ENGINE OIL  
Drain oil (with engine warm) and replace with clean en-  
gine oil. (See “ENGINE” in the Maintenance section of  
this manual).  
1. Clean entire snow thrower (See “CLEANING” in the  
Maintenance section of this manual).  
CYLINDER  
1. Remove spark plug.  
2. Inspect and replace belts, if necessary (See “TO RE-  
PLACEBELTSintheServiceandAdjustmentssection  
of this manual).  
2. Pour one ounce (29 ml) of oil through spark plug hole  
into cylinder.  
3. Lubricate as shown in the Maintenance section of this  
manual.  
3. Pullrecoilstarterhandleslowlyafewtimestodistribute  
oil.  
4. Besurethatallnuts,bolts,screws,andpinsaresecurely  
fastened. Inspect moving parts for damage, breakage  
and wear. Replace if necessary.  
4. Replace with new spark plug.  
5. Touch up all rusted or chipped paint surfaces; sand  
lightly before painting.  
OTHER  
Do not store gasoline from one season to another.  
Replace your gasoline can if your can starts to rust.  
Rust and/or dirt in your gasoline will cause problems.  
ENGINE  
See engine manual.  
If possible, store your snow thrower indoors and cover  
it to protect it from dust and dirt.  
FUEL SYSTEM  
IMPORTANT: It is important to prevent gum deposits from  
forming in essential fuel system parts such as carburetor,  
fuelhose,ortankduringstorage.Also,alcoholblendedfuels  
(called gasohol or using ethanol or methanol) can attract  
moisture which leads to separation and formation of acids  
during storage. Acidic gas can damage the fuel system of  
an engine while in storage.  
Coveryoursnowthrowerwithasuitableprotectivecover  
thatdoesnotretainmoisture.Donotuseplastic.Plastic  
cannotbreathe,whichallowscondensationtoformand  
will cause your snow thrower to rust.  
IMPORTANT: Never cover snow thrower while engine/  
exhaust area is still warm.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
See appropriate section in manual unless directed to a qualified service centre.  
PROBLEM  
CAUSE  
CORRECTION  
Does not start  
1. Fuel shut-off valve (if so  
equipped) in OFF position.  
2. Safety ignition key  
is not inserted.  
1. Turn fuel shut-off valve to OPEN position.  
2. Insert safety ignition key.  
3. Out of fuel.  
3. Fill fuel tank.  
4. Throttle in STOP position.  
5. Choke in OFF position.  
6. Primer not depressed.  
7. Engine is flooded.  
8. Spark plug wire is  
disconnected.  
4. Move throttle to FAST position.  
5. Move to FULL position.  
6. Prime as instructed in the Operation section of this manual.  
7. Wait a few minutes before restarting, DO NOT prime.  
8. Connect wire to spark plug.  
9. Bad spark plug.  
10. Stale fuel.  
11. Water in fuel.  
9. Replace spark plug.  
10. Drain fuel tank and carburetor, refill tank with fresh gasoline.  
11. Drain fuel tank and carburetor, refill tank with fresh gasoline.  
Loss of power  
1. Spark plug wire loose.  
2. Throwing too much snow.  
3. Fuel tank cap is covered  
with ice or snow.  
1. Reconnect spark plug wire.  
2. Reduce speed and width of swath.  
3. Remove ice and snow on and around fuel tank cap.  
4. Dirty or clogged muffler.  
4. Clean or replace muffler.  
Engine idles or  
runs roughly  
1. Choke is in FULL position.  
2. Blockage in fuel line.  
3. Stale fuel.  
4. Water in fuel.  
5. Carburetor is in need of  
adjustment or overhaul.  
1. Move choke to OFF position.  
2. Clean fuel line.  
3. Drain tank and refill with fresh, clean fuel.  
4. Drain fuel tank and carburetor, refill tank with fresh gasoline.  
5. Contact a qualified service centre.  
Excessive  
vibration  
1. Loose parts or damaged  
augers or impeller.  
1. Tighten all fasteners. Replace damaged parts.  
If vibration remains, contact a qualified service centre.  
Recoil starter  
is hard to pull  
1. Frozen recoil starter.  
1. See “IF RECOIL STARTER HAS FROZEN”  
in the Operation section of this manual.  
Loss of traction 1. Drive belt is worn.  
1. Check / replace drive belt.  
2. Check / reinstall drive belt.  
drive / slowing  
of drive speed  
2. Drive belt is off of pulley.  
3. Friction drive wheel is worn. 3. Contact a qualified service centre.  
Loss of snow  
discharge or  
slowing of  
1. Auger belt is off of pulley.  
2. Auger belt is worn.  
3. Clogged discharge chute.  
1. Check / reinstall auger belt.  
2. Check / replace auger belt.  
3. Clean snow chute.  
snow discharge 4. Augers / impeller jammed.  
4. Remove debris or foreign object from augers / impeller.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
AUGER HOUSING / IMPELLER ASSEMBLY  
13  
16  
4
6
15  
6
10  
12  
51  
14  
47  
38  
5
7
36  
9
37  
7
11  
9
42  
44  
27  
8
45  
50  
6
43  
43  
42  
41  
46  
27  
52  
24  
21  
23  
40  
39  
10  
49  
28  
53  
55  
19  
32  
54  
18  
34  
48  
26  
19  
33  
20  
35  
19  
29  
28  
25  
55  
53  
10  
31  
52  
17  
24  
57  
54  
56  
30  
23  
18  
26  
25  
21  
17  
20  
22  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
AUGER HOUSING / IMPELLER ASSEMBLY  
KEY PART  
NO. NO.  
KEY PART  
NO. NO.  
DESCRIPTION  
DESCRIPTION  
4
5
6
7
191079  
Pulley, Impeller  
30 405973X479 Auger Assembly, RH  
31 405972X479 Auger Assembly, LH  
188909  
198541  
180355  
Bearing Assembly, Flange  
Nut, Hex Flange 5/16-18  
Bolt, Flat Head, Carriage  
5/16-18 x 5/8  
Bolt, Carriage 5/16-18  
Bolt, Hex Head  
32 407768  
33 407769  
34 174681  
35 174684  
36 407757  
37 174683  
38 407758  
39 407767  
40 407760  
41 407761  
42 407770  
43 407762  
44 189282  
45 407763  
46 407764  
47 407765  
O-Ring  
Bushing, Flange 3/4  
Washer, Thrust 3/4  
Bearing, Thrust 3/4  
Shaft, Impeller  
Washer, Thrust 5/8  
Bushing, Flange 5/8  
Screw, Hex Head 5/16-18 x 3/4  
Plug, Case  
Housing, Gearbox, RH  
Seal, Oil  
Bushing, Flange, 1"  
Key, Square 1/4 x 1/4 x 7/8  
Gear, Worm  
8
9
72270505  
199879  
10 404927X428 Housing, Auger  
11 404933X479 Bar, Scraper  
12 178675X008 Bracket, Corner Discharge  
13 175322  
14 19111507  
15 198552  
16 74950512  
17 405637  
18 179582  
19 73800400  
20 198541  
21 401347  
Base, Discharge Chute  
Washer, Flat  
Washer, Lock 5/16  
Screw, Hex Head 5/16-18 x 3/4  
Grease Fitting  
Screw, Hex Head 5/16 x 1  
Nut, Hex Lock 1/4-20  
Nut, Hex Lock 5/16-18  
Washer, Flat  
Shaft, Auger  
Housing, Gearbox, LH  
48 175321X479 Impeller Assembly  
22 178777X479 Skid Plate, RH  
49 74780426  
50 407766  
51 7836M  
Screw, Hex Head 1/4-20 x 1-5/8  
Gasket, Gearbox  
Pin, Roll 3/16 x 1-1/8  
24 128638  
25 72270506  
26 174658  
27 174697  
28 198636  
Wing Nut  
Bolt, Carriage 5/16-18 x 3/4  
Bearing, Auger  
Washer, Thrust, 1"  
Bolt, Shear  
52 405697X479 Bar, Drift Cutter  
54 198709  
55 198638  
56 180684  
57 196710  
Stop  
Spacer  
Multi-Wrench  
Gearbox Assembly  
29 174762X479 Skid Plate, LH  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
CONTROL PANEL / DISCHARGE CHUTE  
1
2
2
1
19  
2
22  
3
6
23  
32  
22 26  
27  
36  
33  
4
35  
34  
5
6
20  
9
14  
28  
10  
23  
11  
25  
16  
18  
27  
7
29  
12  
14  
30  
17  
31  
3
8
13  
15  
8
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
CONTROL PANEL / DISCHARGE CHUTE  
KEY PART  
NO. NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
183334  
17501010  
198475  
73800600  
19131316  
198473  
405784X479 Support, Pivot  
150078  
184505  
Knob, Lever  
Screw #10-24 x 5/8  
Control Assembly, Deflector  
Nut, Lock 3/8-16  
Washer, Flat 3/8  
Control Assembly, Chute Rotater  
Screw, Hex Head 5/16-18 x 3/4  
Spring, Deflector  
10 179829  
11 179246  
12 191730  
13 72250505  
14 751153  
Bolt, Shoulder  
Washer, Friction, Nylon  
Nut, Lock 1/4-20  
Bolt, Carriage 5/16-18  
Nut, Lock 5/16-18  
15 404770X428 Chute Assembly  
16 178633X428 Deflector Assembly  
17 179145  
18 128415  
19 183333  
20 198648  
22 74041024  
23 188303  
25 169675  
26 192001  
27 169675  
28 187782  
29 187784  
30 192710  
31 192199  
32 192002  
33 192195  
34 155415  
35 179246  
36 74760552  
Seal, Deflector  
Rivet, Blind  
Knob, Speed Control Lever  
Bolt, Carriage 5/16-18 x 3/4  
Screw #10-24 x 1-1/2  
Control Assembly, Power Steering  
Nut, Lock 5/16-18  
Lever Assembly, Speed Control  
Retainer, Hairpin  
Rod, Upper, Speed Control  
Rod, Lower, Speed Control  
Clamp, Mounting, Clean-Out Tool  
Tool, Clean-Out  
Bracket, Shifter  
Spring, Friction  
Washer, Flat  
Washer, Friction  
Capscrew  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
HANDLES  
2
5
28  
7
5
5
4
6
4
36  
8
45  
42  
9
12  
34  
46  
28  
1
37  
44  
15  
13  
4
43  
34  
15  
19  
11  
4
5
15  
17  
46  
35  
18  
16  
33  
35  
22  
11  
21  
10  
22  
15  
23  
12  
20  
14  
16  
24  
17  
25  
27  
24  
31  
32  
26  
31  
27  
32  
30  
38  
39  
40  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
HANDLES  
KEY PART  
NO. NO.  
DESCRIPTION  
1
2
4
5
6
7
8
9
405999X479 Lever, Auger Control, RH  
405783X479 Lever, Traction Drive Control, LH  
178888  
169675  
17060408  
178652  
Bushing, Flange  
Retainer, Hairpin  
Screw, Hex Head 1/4-20 x 3/4  
Rod, Interlock  
196333X008 Arm, Impeller Rod  
196334X008 Arm, Traction Rod  
10 196619X479 Panel, Control  
11 74780524  
12 74780528  
Screw, Hex Head 5/16-18 x 1-1/2  
Screw, Hex Head 5/16-18 x 1-3/4  
13 407856X479 Handle Tube, LH  
14 407857X479 Handle Tube, RH  
15 751153  
16 19131316  
17 178899  
18 193433  
19 179098  
20 180428  
21 73350500  
22 72120618  
Nut, Lock 5/16-18  
Washer, Flat 3/8  
Knob, Handle  
Rod, Auger Control  
Rod, Traction Control  
Rod, Auger Control  
Nut, Hex, Jam 5/16-18  
Bolt, Carriage 3/8-16 x 2-1/4  
23 178643X479 Handle Tube, Lower  
24 192091  
25 180926  
26 178669  
27 17000616  
28 198559  
30 182906  
31 175262  
32 184471  
Sleeve, Spring  
Spring, Traction Drive  
Spring, Auger Control  
Screw, Hex Head 3/8-16 x 1  
Bushing, Pivot Lever  
Console, Panel  
Screw, Hex Head, Tapping #10-24 x 1-1/4  
Screw, Hex Head, Tapping #10-24 x 1/2  
33 196335X008 Latch, Interlock  
34 183518  
35 68038  
36 178831  
37 193885  
38 178666  
- - 401620  
39 178668  
40 180964  
Bolt, Shoulder  
Nut, Lock 1/4-20  
Spring, Torsion, Lever  
Spring, Interlock  
Headlight, Halogen (Includes Bulb)  
Bulb, Halogen  
Bezel, Headlight  
Harness, Headlight (Halogen)  
42 196336X008 Lever, Interlock  
43 196337  
44 196338  
45 700279  
46 57079  
Rod, Latch, Interlock  
Rod, Arm, Interlock  
Clip  
Washer, Hardened  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
DRIVE  
13  
19  
22  
23  
21  
18  
13  
1
5
3
2
20  
16  
1
5
9
6
14  
13  
15  
11  
7
2
4
3
10  
12  
13  
8
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
DRIVE  
KEY PART  
NO. NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
198584  
Screw, Hex Head 5/16-18 x 1/2  
Spacer, Axle  
Washer, Thrust  
Screw, Cap, Hex Head 3/8-16 x 2  
Bearing, Axle  
Nut, Hex, Centerlock 3/8-16  
Transmission Assembly  
Speed Control Arm, Hydro  
Retainer Clip  
187794  
174697  
74780632  
179830  
73930600  
187776  
187787  
700279  
10 188101  
Torque Strap  
11 193255X479 Bracket, Anti-Rotate  
12 73800400  
13 150078  
14 193256  
15 191995  
16 404308  
18 198466  
19 192000  
20 191993  
21 87930  
Nut, Hex, Nylock 1/4-20  
Screw, Hex Washer Head 5/16-18 x 3/4  
Rod, Bypass Valve  
Pop Rivet  
Shaft, Axle  
Cable, Drive Control  
Bracket, Cable, Rear  
Bracket, Cable, Front  
Clip, Cable  
22 17391208  
23 146315  
Screw, Slotted Hex Head 1/8 x 1/2  
Screw, Hex Head 5/16-18 x 3/4  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
CHASSIS / ENGINE / PULLEYS  
3
30  
53  
22  
58  
57  
17  
19  
28  
6
10  
25  
21  
26  
23  
4
6
31  
10  
21  
24  
29  
31  
27  
18 20  
6
7
16  
2
9
1
14  
50  
51  
7
8
52  
34  
13  
35  
44  
15  
12  
44  
5
45  
49  
48  
5
46  
47  
47  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
CHASSIS / ENGINE / PULLEYS  
KEY PART  
NO. NO.  
DESCRIPTION  
1
2
3
192873  
180522  
- - -  
Spring, Traction Idler  
Pulley, Idler (2-1/4)  
Engine, Tecumseh, Model Number LH358SA  
(For engine service and replacement parts,  
call Tecumseh Products at 1-800-558-5402)  
Screw, Hex Head 5/16-18 x 1-1/4  
Washer, Flat  
Nut, Jam, Lock 5/16-18  
Pin, Idler Pivot  
V-Belt, Traction Drive  
4
6
7
8
9
74780520  
59289  
166785  
175330  
187788  
10 198552  
11 198584  
Washer, Lock 5/16  
Screw, Hex Washer Head  
5/16-18 x 1/2  
12 179259  
13 85179  
Impeller Arm / Pad Assembly  
Retainer, Hairpin  
14 178828  
15 408010  
16 150406  
17 187786  
18 74780524  
19 198559  
20 180523  
21 74610516  
22 179371  
23 180478  
24 179157  
25 400026  
26 850263  
27 851084  
28 193607  
29 192213  
Spring, Brake  
V-Belt, Impeller Drive  
Screw, Hex Head 3/8-16 x 1-1/4  
Arm, Idler  
Screw, Hex Head 5/16-18 x 1-1/2  
Bushing, Idler Pivot  
Pulley, Idler (2-3/4)  
Screw, Hex Head 5/16-18 x 1  
Spacer, Engine Pulley  
Pulley, Engine, Traction Drive  
Pulley, Engine, Impeller Drive  
Washer, Flat 3/8  
Washer, Lock 3/8  
Screw, Hex Head 3/8-24 x 1-3/8  
Guide, Belt  
Belt Cover Assembly  
(Includes Toolbox Cover)  
Cover, Toolbox  
Screw, Hex Head 1/4-20 x 1/2  
Screw, Hex Head 1/4-28 x 3/4  
Arm, Auger Control  
30 178830  
31 405024  
34 198580  
35 405484  
44 17000616  
Screw, Hex Head 3/8-16  
45 193397X479 Bracket, Pivot, Idler  
46 187785X479 Pan, Frame Bottom  
47 71020512  
48 181156  
Screw, Hex Head 5/16-18 x 3/4  
Nut, Speed 5/16-18  
49 404431X428 Frame Assembly  
50 192115X428 Plate, Frame End  
51 406109  
52 57079  
Shaft, Auger Control  
Washer, Hardened  
57 11050500  
58 198563  
Washer, Lock, External Tooth 5/16  
Power Cord  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
WHEELS / DECALS  
18  
14  
27  
10  
30  
15  
32  
13  
10  
20  
12  
17  
19  
11  
11  
7
2
28  
8
28  
26  
22  
29  
31  
11  
25  
4
7
24  
23  
9
4
33  
21  
3
4
1
4
34  
24  
3
22  
29  
25  
21  
33  
2
23  
14  
28  
30  
26  
18  
10  
28  
15  
12  
27  
11  
16  
19  
34  
11  
20  
32  
13  
1
2
4
12  
9
8
6
7
5
11  
10  
3
1
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
REPAIR PARTS  
SNOW THROWER - MODEL PP11H30ES (96192001400)  
WHEELS / DECALS  
KEY PART  
NO. NO.  
DESCRIPTION  
1
2
3
4
7
8
9
196752X421 Wheel Assembly, 16", Power Steering, LH  
155443  
405161  
184471  
17000616  
Pin, Klik 1/4  
Cover, Power Steering  
Screw, Hex Head #10-24 x 1/2  
Capscrew, Hex Head, Flanged 3/8-16 x 1  
185603X479 Bracket, Steering Cable, RH  
185602X479 Bracket, Steering Cable, LH  
10 17600406  
11 198584  
12 406057  
Screw, Hex Head 1/4-20 x 3/8  
Screw, Hex Head 5/16-18 x 1/2  
Link, Steering Lever  
13 193506X498 Yoke, Steering  
14 182015 Pin, Steering Lever  
15 194944X008 Bellcrank  
16 194939X008 Bracket, LH Steering  
17 194943X008 Bracket, RH Steering  
18 181847  
19 85179  
Pin, Steering Bellcrank  
Retainer, Hairpin  
20 179148X479 Bracket, Steering  
21 192126  
22 182466  
23 187622  
24 194941  
25 179139  
26 194940  
27 189282  
28 174697  
29 179830  
30 193885  
Driver, Wheel  
Ring, Wire Retainer  
Lobe, Wheel  
Slide, Clutch  
Spring, Clutch Slide  
Lobe, Axle  
Key, Square 1/4 x .875  
Washer, Thrust (1")  
Bearing, Axle  
Spring, Return, Steering Latch  
31 196753X421 Wheel Assembly, 16", Power Steering, RH  
32 700279  
33 12000045  
34 146315  
Clip, Retainer  
Ring, Retaining  
Screw, Hex Head, Tapping 5/16-18 x 5/8  
KEY PART  
NO. NO.  
DESCRIPTION  
1
2
3
4
5
6
7
8
9
181037  
187867  
181035  
181042  
187892  
181033  
155798  
155800  
181039  
Decal, Danger  
Decal, Poulan Pro, 11 HP / 30"  
Decal, Danger, Deflector  
Decal, Danger  
Decal, Poulan Pro  
Decal, Instruction  
Decal, Traction Lever  
Decal, Auger Lever  
Decal, Speed Control  
Decal, Remote Deflector Control  
Decal, LH Trigger  
Decal, RH Trigger  
Owner’s Manual, English  
Owner’s Manual, French  
10 183730  
11 183907  
12 183905  
- - 406281  
- - 406282  
NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mm  
IMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement parts.  
Failure to do so could be hazardous, damage your snow thrower and void your warranty.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
LIMITED WARRANTY  
The Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects  
in materials and workmanship. For a period of two (2) years from date of purchase by the original consumer pur-  
chaser, we will repair or replace, at our option, without charge for parts or labor incurred in replacing parts, any part  
which we find to be defective due to materials or workmanship. This Warranty is subject to the following limitations  
and exclusions.  
1. This warranty does not apply to the engine or components parts thereof. Please refer to the applicable manu-  
facturer's warranty on these items.  
2. Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the  
purchaser. Transportation charges for any parts submitted for replacement under this warranty must be paid by  
the purchaser unless such return is requested by the manufacturer.  
3. The Warranty period for any products used for rental or commercial purposes is limited to 90 days from the date  
of original purchase.  
4. This Warranty applies only to products which have been properly assembled, adjusted, operated, and maintained  
in accordance with the instructions furnished. This Warranty does not apply to any product which has been sub-  
jected to alteration, misuse, abuse, improper assembly or installation, delivery damage, or to normal wear of the  
product.  
5. Exclusions: Excluded from this Warranty are belts, shear pins, normal wear, normal adjustments, standard hard-  
ware and normal maintenance.  
6. In the event you have a claim under this Warranty, you must return the product to an authorized service dealer.  
Should you have any unanswered questions concerning this Warranty, please contact:  
In Canada contact:  
Poulan Pro  
Poulan Pro, Customer Service Department  
Customer Service Department  
5855 Terry Fox Way  
1030 Stevens Creek Road  
Mississauga, Ontario  
Augusta, GA 30907 USA  
L5V 3E4  
giving the complete mfg. ID#, serial number and date of purchase of your product and the name and address of the  
authorized dealer from whom it was purchased.  
THIS WARRANTY DOES NOT APPLY TO INCIDENTAL OR CONSEQUENTIAL DAMAGES AND ANY IMPLIED  
WARRANTIES ARE LIMITED TO THE SAME TIME PERIODS STATED HEREIN FOR OUR EXPRESSED WAR-  
RANTIES. Some areas do not allow the limitation of consequential damages or limitations of how long an implied  
Warranty may last, so the above limitations or exclusions may not apply to you. This Warranty gives you specific  
legal rights, and you may have other rights which vary from locale to locale.  
This is a limited Warranty within the meaning of that term as defined in the Magnuson-Moss Act of 1975.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pentair Landscape Lighting PG2000 User Manual
Philips CRT Television 14PT3525 V7 User Manual
Philips CRT Television TS2768C User Manual
Philips Headphones SBC HC060 User Manual
Philips MP3 Player ACT400 17 User Manual
Philips Refrigerator AZ9217 User Manual
Philips Speaker HTL4110B User Manual
Philips Stereo System SWA3304W User Manual
Poulan Blower 530088953 User Manual
PYLE Audio Car Video System PL2DNTV7 User Manual