R
Please do not return unit to retailer.
Por favor, no devuelva el aparato al lugar de compra.
Veuillez ne pas retourner l’outil au détaillant.
1--800--554--6723
Instruction Manual
Manual de Instrucciones
Manuel d’Instructions
SM400
IMPORTANT MANUAL -- Do not throw away
MANUAL IMPORTANTE - No lo descarte
MANUEL IMPORTANT -- À Conserver
WARNING:
Read and follow all Safety Rules and Operating Instructions before
using this product. Failure to do so can result in serious injury.
ADVERTENCIA:
Lea el manual de instrucciones y siga todas las advertencias e
instrucciones de seguridad. El no hacerlo puede resultar en lesiones
graves.
AVERTISSEMENT:
Veuillez lire le manuel d’instructions et bien respecter tous les
avertissements et toutes les instructions de sécurité. Tout défaut
de le faire pourrait entraîner des blessures graves.
Poulan PRO
1030 Stevens Creek Road
Augusta, GA 30907
545117517
7/31/06
Download from Www.Somanuals.com. All Manuals Search And Download.
IDENTIFICATION OF SAFETY SYMBOLS
WARNING: Stop the engine before opening the vacuum inlet door. The engine must
be stopped and the impeller blades no longer turning to avoid serious injury from the rotating
blades. Gently tilt the handle of the screwdriver toward the back of the unit to release the latch
while pulling up on the vacuum inlet cover with your other hand.
When using the vacuum attachment, the unit is designed to pick up dry
material such as leaves, grass, small twigs, and bits of paper. Do not
vacuum stones, gravel, metal, broken glass, etc., to avoid severe dam-
age to the impeller.
WARNING: Fire hazard. Never mix, pour, or store gasoline or
use the unit near a flame or sparks (including smoking, open flames, or
work that can cause sparks).
SAFETY RULES
PLAN AHEAD
WARNING: Failure to follow all
Safety Rules and Precautions can result in
serious injury.
D Always wear eye protection when operat-
ing, servicing, or performing maintenance
on unit. Wearing eye protection will help to
prevent rocks or debris from being blown or
ricocheting into eyes and face which can
result in blindness and/or serious injury.
Eye protection should be marked Z87.
D Always wear foot protection. Do not go
barefoot or wear sandals.
KNOW YOUR UNIT
S Read your instruction manual carefully until
you completely understand and can follow
all warnings and safety rules before operat-
ing the unit.
D Always wear respirator or face mask when
working with unit in dusty environments.
D Secure hair above shoulder length. Secure or
remove jewelry, loose clothing, or clothing
with loosely hanging straps, ties, tassels, etc.
They can be caught in moving parts.
D Restrict unit to users who understand and
will follow all warnings and safety rules in
this manual.
WARNING: Inspect area before start-
ing unit. Remove all debris and hard objects
such as rocks, glass, wire, etc. that can rico-
chet, be thrown, or otherwise cause injury or
damage during operation.
D Do not operate unit when you are tired, ill, up-
set, or if you are under the influence of alco-
hol, drugs, or medication.
D Keep children, bystanders, and animals
away from work area a minimum of 30 feet
(10 meters) when starting or operating unit.
Do not point the blower nozzle in the direc-
tion of people or pets.
Use your unit as a blower for:
D
Sweeping debris or grass clippings from
driveways, sidewalks, patios, etc.
Blowing grass clippings, straw, or leaves into
piles, around joints, or between bricks.
D
HANDLE FUEL WITH CAUTION, IT IS
HIGHLY FLAMMABLE
Use your unit as a vacuum for:
D Eliminate all sources of sparks or flame (in-
cluding smoking, open flames, or work that
can cause sparks) intheareas where fuelis
mixed, poured, or stored.
D
D
D
Picking up dry material such as leaves,
grass, small twigs, and bits of paper.
For best results during vacuum use, operate
your unit at high speed.
Move slowly back and forth over the mate-
rial as you vacuum. Avoid forcing the unit
intoa pile of debris as this can clog theunit.
Keep the vacuum tube about an inch above
the ground for best results.
D Mix and pour fuel in an outdoor area; store
fuel in a cool, dry, well ventilated place; use
an approved, marked container for all fuel
purposes.
D
D Do not smoke while handling fuel or while
operating the unit.
-- 3 --
Download from Www.Somanuals.com. All Manuals Search And Download.
D Make sure the unit is properly assembled
and in good operating condition.
D
D
To avoid spreading fire, do not use near
leaf or brush fires, fireplaces, barbecue
pits, ashtrays, etc.
D Do not fill fuel tank while engine is hot or
running.
Use only for jobs explained in this manual.
D Avoid spilling fuel or oil. Wipe up fuel spills
before starting engine.
D Move at least 10 feet (3 meters) away from
fuel and fueling site before starting engine.
D Always store gasoline in a container ap-
proved for flammable liquids.
MAINTAIN YOUR UNIT PROPERLY
D Have all maintenance other than the rec-
ommended procedures described in the in-
struction manual performed by an autho-
rized service dealer.
D Disconnect spark plug before performing
maintenance except for carburetor adjust-
ments.
OPERATE YOUR UNIT SAFELY
D Use only recommended Poulan PRO re-
placement parts; use of any other parts
may void your warranty and cause damage
to your unit.
WARNING: Stop the engine before
opening the vacuum inlet door. The engine
must be stopped and the impeller blades no
longer turning to avoid serious injury from the
rotating blades.
D Inspect unit before each use for worn,
loose, missing, or damaged parts. Do not
use until unit is in proper working order.
D Keep outside surfaces free of oil and fuel.
D Never start or run engine inside a closed
room, building or other unventilated area.
Breathing exhaust fumes can kill.
D To avoid static electricity shock, do not
wear rubber gloves or any other insulated
gloves while operating unit.
D Empty fuel tank before storing the unit. Use
up fuel left in carburetor by starting engine and
letting it run until it stops.
D Do not use any accessory or attachment
other than those recommended by manufac-
turer for use with your unit.
D Do not store the unit or fuel in a closed area
where fuel vapors can reach sparks or an
open flame from hot water heaters, electric
motors or switches, furnaces, etc.
D Store in a dry area out of reach of children.
D Do not set unit on any surface except a
clean, hard area while engine is running.
Debris such as gravel, sand, dust, grass,
etc. could be picked up by the air intake and
thrown out through discharge opening,
damaging unit, property, or causing serious
injury to bystanders or operator.
SPECIAL NOTICE: Exposure to vibra-
tions through prolonged use of gasoline pow-
ered hand tools could cause blood vessel or
nerve damage in the fingers, hands, and
joints of people prone to circulation disorders
or abnormal swelling. Prolonged use in cold
weather has beenlinked to blood vesseldam-
age in otherwise healthy people. If symptoms
occur such as numbness, pain, loss of
strength, change in skin color or texture, or
loss of feeling in the fingers, hands, or joints,
discontinue the use of this tool and seek
medical attention. An antivibration system
does not guarantee the avoidance of these
problems. Users who operate power tools on
a continual and regular basis must monitor
closely their physical condition and the condi-
tion of this tool.
D Avoid dangerous environments. Do not use
in unventilated areas or where explosive
vapors or carbon monoxide build up could
be present.
D Do not overreach or use from unstable sur-
faces such as ladders, trees, steep slopes,
rooftops, etc. Keep firmfooting andbalance
at all times.
D Never place objects inside the blower
tubes; always direct the blowing debris
away frompeople, animals, glass, andsolid
objects such as trees, automobiles, walls,
etc. The forceof aircan causerocks, dirt, or
sticks to be thrown or to ricochet which can
hurt people or animals, break glass, or
cause other damage.
SPECIAL NOTICE: For users on U.S. For-
est Land and in some states, including Cali-
fornia (Public Resources Codes 4442 and
4443), Idaho, Maine, Minnesota, New Jersey,
Oregon, and Washington: Certain internal
combustion engines operated on forest,
brush, and/or grass covered landin the above
areas are required to be equipped with a
spark arresting screen, maintained in effec-
tive working order, or the engine must be con-
structed, equipped, and maintained for the
prevention of fire. Check with your state or lo-
cal authorities for regulations pertaining to
these requirements. Failure to follow these
requirements is a violation of thelaw. This unit
is not factory equipped with a spark arresting
screen; however, a spark arresting screen is
available as an optional part. If a spark arrest-
ing screen is required in your area, contact
your authorized service dealer for the correct
kit. The spark arresting screen, blower tubes,
and nozzles must be assembled to unit to be
in full compliance with regulations.
D
Never run unit without the proper equip-
ment attached. When using your unit as a
blower, always install blower tubes. When
usingyour unit as a vacuum, always install
vacuum tubes and vacuum bagassembly.
Make sure vacuum bag assembly is com-
pletely zipped.
D
Check air intake opening, blower tubes,
vacuum tubes, and elbow tube frequently,
always with engine stopped and spark
plug disconnected. Keep vents and dis-
charge tubes free of debris which can ac-
cumulate and restrict proper air flow.
Never place any object in the air intake
opening as this could restrict proper air flow
and cause damage to the unit.
D
D
Never use for spreading chemicals, fertil-
izers, or other substances which may con-
tain toxic materials.
-- 4 --
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
Rib
Groove
WARNING: If you receive your unit
assembled, check each step to insure your
unit is properly assembled and all fasteners
are secure. Follow all safety information in
the manual and on the unit.
5. Insert theelbow tube into the blower outlet.
Make sure elbow tube rib is aligned with
the blower outlet groove.
D
A standard screwdriver is required for as-
sembly.
6. Turn knob clockwiseto secure elbow tube.
BLOWER TUBE ASSEMBLY
1. Align the rib on the blower tube with the
groove in the blower outlet; slide the tube
into place.
NOTE: Knob must be loose enough to allow
blower tube to be inserted in blower outlet.
Loosen knob by turning counterclockwise.
VACUUM TUBE ASSEMBLY
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury.
1. Align the lower vacuum tube as shown.
Push lower vacuum tube into upper vacu-
um tube.
Blower
Blower
Outlet
Tube
Upper Vacuum
Tube
Groove
Rib
2. Secure the tube by turning the knob clock-
Lower Vacuum Tube
wise.
3. To remove the tube, turn the knob counter-
clockwise to loosen the tube; remove the
tube.
2. Insert the tip of a screwdriver into the latch
area of the vacuum inlet.
Blower
Latch
Outlet
Ar
VACUUM BAG ASSEMBLY
1. Open the zipper on the vacuum bag and
insert the elbow tube.
Latch Area
Vacuum
Inlet Cover
2. Push the small end of the elbow tube
through the small opening in the bag.
Elbow
Tube
3. Gently tilt the handle of the screwdriver to-
ward the back of the unit to release the
latch while pulling up on the vacuum inlet
cover with your other hand.
4. Hold the vacuum inlet cover open until up-
per vacuum tube is installed.
Small
Opening
Zipper
Opening
Rib
Vacuum Inlet
NOTE: Make sureedge of the small opening
is flush against the flared area of the elbow
tube, and the rib on the elbow tube is on the
bottom.
Retaining Post
Vacuum
Inlet
Cover
3. Close the zipper on the bag. Make sure the
zipper is closed completely.
4. Remove blower tube from engine.
-- 5 --
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Placethehooks on the upper vacuumtube
on the retaining posts of the unit.
SHOULDER STRAP ADJUSTMENT
1. Hold the unit as shown with the muffler side
facing away from your body and clothes.
2. Pass the shoulder strap over your head
and onto your right shoulder.
6. Pivot the tube until it is secured to the
blower unit by the vacuum inlet latch.
3. Extend your left arm toward the rear of the
vacuum bag.
PIVOT
Inlet Cover
4. Adjust shoulder strap until the vacuum
bag/shoulder strap seam lies between
your thumb and index finger.
5. Make sure air flows freely from the elbow
tube into bag. If bag is kinked, the unit will
not operate properly.
Latch
Retaining
Hook
Post
HOW TO CONVERT UNIT FROM
VACUUM USE TO BLOWER USE
1. Remove the vacuum tubes by inserting
the tip of a screwdriver into the latch area
of the vacuum inlet.
2. Gently tilt handle of screwdriver toward
the back of the unit to release the latch
while pulling up on the upper vacuum tube
with your other hand.
Latch Area
3. Remove the vacuum bag.
4. Close the vacuum inlet cover and make
sure it is latched closed.
5. Reinstall the blower tube (see BLOWER
TUBE ASSEMBLY).
-- 6 --
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
KNOW YOUR BLOWER
READ THIS INSTRUCTION MANUAL AND SAFETY RULES BEFORE OPERATING YOUR UNIT.
Compare the illustrations with your unit to familiarize yourself with the location of the various controls
and adjustments. Save this manual for future reference.
Upper
Lower
Vacuum Tube
Primer Button
Choke Lever
Vacuum Bag
Fuel Mix
Throttle
Fill Cap
Lever
Starter
Rope
Spark Plug
Elbow Tube
Blower
Tube
Rear
Handle
THROTTLE LEVER
CHOKE LEVER
The THROTTLE LEVER is used to select the
desired engine speed and to stop the engine.
The CHOKE helps to supply fuel to the engine
to aid in cold starting. Activate the choke by
moving the choke lever to the FULL CHOKE
position. After engine attempts to start, move the
choke lever to the HALF CHOKE position.
Once engine starts, move choke lever to the
RUN position.
Movethethrottlelever to the
full speed operation. Move the throttle lever
position for
to the
positionfor idlespeed. To stop the
engine, move the throttle lever to the STOP
position.
PRIMER BUTTON
The PRIMER BUTTON removes air from the
carburetor and fuel lines and fills them with fuel.
This allows you to start the engine with fewer
pulls on the starter rope. Activate primer button
by pressing it and allowing it to return to its origi-
nal position.
S To reduce the risk of hearing loss
associated with sound level(s), hearing
protection is required.
OPERATING POSITION
ye
otec
S To reduce the risk of injury associated with
contacting rotating parts, stop the engine be-
fore installing or removing attachments. Do
not operate without guard(s) in place.
S Operate power equipment only at reasonable
hours--not early in the morning or late at night
when people might be disturbed. Comply with
times listed in local ordinances. Usual recom-
mendations are 9:00 a.m. to 5:00 p.m.,
Monday though Saturday.
S To reduce noise levels, limit the number of
pieces of equipment used at any one time.
S To reduce noise levels, operate power
blowers at the lowest possible throttle
speed to do the job.
S Use rakes and brooms to loosen debris be-
fore blowing.
Blower
OPERATING TIPS
Vacuum
S While vacuuming or blowing debris, hold
the unit with the muffler side facing away
from your body and clothes (see OPERAT-
ING POSITION illustration above).
-- 7 --
Download from Www.Somanuals.com. All Manuals Search And Download.
S In dusty conditions, slightly dampen sur-
faces or use a mister attachment when wa-
ter is available.
NOTE: Unit must be placed on its side when
adding fuel (see illustration below).
S Conserve water by using power blowers
instead of hoses for many lawn and garden
applications, including areas such as gutters,
screens, patios, grills, porches, and gardens.
S Watchout for children, pets, openwindows,
or freshly washed cars. Blow debris away
safely.
S Use the full blower nozzle extension so the
air stream can work close to the ground.
S After using blowers and other equipment,
CLEAN UP! Dispose of debris in trash re-
ceptacles.
BEFORE STARTING ENGINE
WARNING: Be sure to read the fuel
information in the safety rules before you be-
gin. If you do not understand the safety rules,
do not attempt to fuel your unit. Call
1-800-554-6723.
TO STOP THE ENGINE
FUELING ENGINE
D To stop the engine, move the throttle lever
to the STOP position.
WARNING: Remove fuel cap slowly
BEFORE STARTING THE ENGINE
when refueling.
WARNING: You MUST make sure
HELPFUL TIP
To obtain the correct oil mix
ratio, pour 3.2 ounces of
2-cycle synthetic oil into
one gallon of fresh gas.
the tubes are secure before using the unit.
D
Fuel engine. Move at least 10 feet (3 me-
ters) away from the fueling site.
Hold the unit in the starting position as
shown. Make sure the blower end is di-
rected away from people, animals, glass,
and solid objects.
D
This engine is certified to operate on
unleaded gasoline. Before operation,
gasoline must be mixed with a good quality
synthetic 2-cycle air-cooled engine oil
designed to bemixed at a ratioof 40:1. Poulan
PRO brand synthetic oil is recommended.
Mix gasoline and oil at a ratio of 40:1. A 40:1
ratio is obtained by mixing 3.2 ounces (95 ml)
of oil with 1 gallon (4 liters) of unleaded
gasoline. DO NOT USE automotive oil or
boat oil. These oils will cause engine damage.
When mixing fuel, follow instructions printed
on container. Once oil is added to gasoline,
shake container momentarily to assure that
the fuel is thoroughly mixed. Always read and
follow the safety rules relating to fuel before
fueling your unit.
STARTING POSITION
Blower
WARNING: When starting engine,
IMPORTANT
hold the unit as illustrated. Do not set unit on any
surface except a clean, hard area when starting
engine or while engine is running. Debris such
as gravel, sand, dust, grass, etc. could be
picked up by the air intake and thrown out
through the discharge opening, damaging the
unit or property, or causing serious injury to by-
standers or the operator.
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which leads to
separation and formation of acids during
storage. Acidic gas can damage the fuel
system of an engine while in storage. Toavoid
engine problems, empty the fuel system
before storage for 30 days or longer. Drain the
gas tank, start theengine and let it run until the
fuel lines and carburetor are empty. Use fresh
HELPFUL TIP
If your engine still does not
start after following these
instructions, please call
1 -800 -554-6723.
fuel next season.
Never use engine or
carburetor cleaner products in the fuel tank or
permanent damage may occur.
-- 8 --
Download from Www.Somanuals.com. All Manuals Search And Download.
If engine has not started after 5 pulls (at HALF
CHOKE), repeat STARTING A COLD ENGINE
procedure. If engine still does not start, proceed
to STARTING A FLOODED ENGINE.
9. To stop the engine, move the throttle lever to
the STOP position.
STARTING A COLD ENGINE
1. Move throttle lever to the
position.
2. Move choke lever to the FULL CHOKE
position.
3. Slowly press the primer button 8 times.
T
STARTING A WARM ENGINE
NOTE: If fuel tank is empty, add fuel; then,
follow STARTING A COLD ENGINE proce-
dure. Do not fill fuel tank while engine is hot.
1. Move throttle lever to the
position.
2. Pull starter rope sharply until engine runs,
but no more than 5 pulls.
NOTE: If engine has not started, pull starter
rope 5 more pulls. If engine still does not run,
it is probably flooded.
3. To stop the engine, move the throttle lever to
the STOP position.
Choke Lever
4. Pull starter rope sharply until engine at-
tempts to run, but no more than 5 pulls (be-
low 30_ F, 8 pulls).
STARTING A FLOODED ENGINE
Flooded engines can be started by placing the
choke lever in the RUN position. Move throttle
NOTE: If engine attempts to start before the
th
5
pull, go to next step immediately.
lever to the fast position
; then, pull rope
5. Move the choke lever to the HALF
CHOKE position.
until engine starts. After engine starts, move the
6. Pull the starter rope sharply until the en-
gine runs, but no more than 5 pulls (below
30_ F, 10 pulls).
throttle lever to the slow position
engine to idle.
to allow
Starting could require pulling the starter rope
many times depending on how badly the unit is
flooded.
If unit still doesn’t start refer to the TROUBLE-
SHOOTING TABLE or call 1-800-554-6723.
7. After a 5 second warm--up, move the
choke lever to the RUN position.
8. Allow the unit to run for 30 more seconds
at the RUN position before moving the
throttle lever to
position.
MAINTENANCE
GENERAL RECOMMENDATIONS
Thewarranty onthis unit does not cover items
that have been subjected to operator abuse
or negligence. To receive full value from the
warranty, the operator must maintain unit as
instructed in this manual. Various adjust-
ments will need to be made periodically to
properly maintain your unit.
WARNING: Avoid touching muffler
unless engine and muffler are cold. A hot
muffler can cause serious burns.
WARNING: Stop engine and be sure
the impeller blades have stopped turning be-
fore opening the vacuum inlet door or at-
tempting to insert or remove the vacuum or
blower tubes. The rotating blades can cause
serious injury. Always disconnect the spark
plug before performing maintenance or ac-
cessing movable parts.
CHECK FOR LOOSE
FASTENERS AND PARTS
S Spark Plug Boot
S Air Filter
S Housing Screws
S Muffler
CHECK FOR DAMAGED OR WORN
PARTS
HELPFUL TIP
IMPORTANT: Have all
repairs other than the rec-
Contact an authorized service dealer for re-
placement of damaged or worn parts.
S Fuel Tank -- Do not use unit if fuel tank shows
signs of damage or leaks.
ommended maintenance
described in the instruction
manual performed by an
S Vacuum Bag -- Do not use vacuum bag if it
is torn or damaged.
authorized service dealer.
If any dealer other than an authorized
service dealer performs work on the
product, Poulan PRO may not pay for
repairs under warranty. It is your re-
sponsibility to maintain and perform
general maintenance.
INSPECT AND CLEAN UNIT AND
DECALS
S After each use, inspect complete unit for
loose or damaged parts. Clean the unit and
decals using a damp cloth with a mild deter-
gent.
S Wipe off unit with a clean dry cloth.
-- 9 --
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAN AIR FILTER
REPLACE FUEL FILTER
Toreplacefuelfilter, drain unit by running it dry
of fuel, then remove fuel cap/retainer assem-
bly from tank. Pull filter from tank and remove
it fromthe fuelline. Install new fuel filter onfuel
line; reinstall parts.
Air Filter
Cover
Fuel Line
Fuel Filter
Screws
CHECK MUFFLER MOUNTING
Air Filter
SCREWS
Once each year, ensure muffler mounting
screws are secure and tightened properly to
Cleaning the air filter:
prevent damage.
Mounting
A dirty air filter decreases engine perform-
ance and increases fuel consumption and
harmful emissions. Always clean or replace
air filter after every 5 hours of operation or
yearly, whichever comes first.
Screw
Holes
Muffler Cover
1. Clean the cover and the area around it to
keep debris from falling into the carburetor
chamber when the cover is removed.
2. Remove parts as illustrated.
Screws
NOTE: Do not cleanfilter ingasoline or other
flammable solvent. Doing so can create a fire
hazard or produce harmful evaporative emis-
sions.
3. Wash the filter in soap and water.
4. Allow filter to dry.
1. Loosen and remove the 2 screws from the
muffler cover.
5. Apply a few drops of oil to the filter;
squeeze filter to distribute oil.
2. Remove the muffler cover.
3. Tighten the 2 muffler mounting screws se-
curely.
6. Replace parts.
4. Reinstall muffler cover and 2 screws.
REPLACE SPARK PLUG
Tighten securely.
Replace spark plug each year to ensure the
engine starts easier and runs better. Set
spark plug gap at 0.025 inch. Ignition timing is
fixed, nonadjustable.
CARBURETOR ADJUSTMENTS
There is no screw for idle adjustment on your
blower. The throttle lever is used to control
engine speed. The throttle lever can be
placed in one of four positions: STOP, IDLE
1. Twist, then pull off spark plug boot.
2. Remove spark plug from cylinder and dis-
card.
or
, FULL THROTTLE or
, and one
3. Replace with Champion RCJ-6Y spark
plug and tighten securely with a 3/4 inch
socket wrench.
intermittent position. If your enginewill not run
properly or you require further assistance,
contact an authorized service dealer or call
1--800--554--6723.
4. Reinstall the spark plug boot.
STORAGE
S Store unit and fuel well out of the reach of
children.
WARNING: Perform the following
steps after each use:
SEASONAL STORAGE
S Allow engine to cool, and secure the unit
before storing or transporting.
Prepare unit for storage at end of season or if
it will not be used for 30 days or more.
If your unit is to be stored for a period of time:
S Clean the entire unit before lengthy stor-
age.
S Store unit and fuel in a well ventilated area
where fuel vapors cannot reach sparks or
open flames from water heaters, electric
motors or switches, furnaces, etc.
S Store unit with all guards in place. Position
unit so that any sharp object cannot acci-
dentally cause injury.
S Store in a clean dry area.
S Lightly oil external metal surfaces.
-- 1 0 --
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL SYSTEM
ENGINE
Under FUELING ENGINE in the OPERA-
TION section of this manual, see messagela-
beled IMPORTANT regarding the use of ga-
sohol in your engine.
S Remove spark plug and pour 1 teaspoon of
40:1, 2-cycle engine oil (air cooled) through
the spark plug opening. Slowly pull the
starter rope 8 to 10 times to distribute oil.
S Replace spark plug with new one of recom-
mended type and heat range.
Fuel stabilizer is an acceptable alternative in
minimizing the formation of fuel gum deposits
during storage. Add stabilizer to gasoline in fuel
tank or fuel storage container. Follow the mix
instructions found on stabilizer container. Run
engine at least 5 minutes after adding stabilizer.
S Clean air filter.
S Check entire unit for loose screws, nuts,
and bolts. Replace any damaged, broken,
or worn parts.
S At the beginning of the next season, use
only fresh fuel having the proper gasolineto
oil ratio.
HELPFUL TIP
During storage of your gas/
oil mixture, the oil will sepa-
rate from the gas.
We recommend that you
shake the gas can weekly
to insure proper blending of
the gas and oil.
OTHER
S Do not store gasoline from one season to
another.
S Replace your gasoline can if it starts to rust.
TROUBLESHOOTING TABLE
WARNING: Always stop unit and disconnect spark plug before performing any of the
recommended remedies below other than remedies that require operation of the unit.
TROUBLE
Engine will not
start.
CAUSE
1. Engine flooded.
REMEDY
1. See “Starting a Flooded Engine”
in Operation section.
2. Fill tank with correct fuel mixture.
3. Install new spark plug.
2. Fuel tank empty.
3. Spark plug not firing.
4. Fuel not reaching
carburetor.
4. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
5. Contact an authorized service dealer.
5. Compression low.
1. Fuel not reaching
1. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
Engine will not
idle properly.
carburetor.
2. Carburetor requires
adjustment.
3. Crankshaft seals worn.
4. Compression low.
2. Contact an authorized service dealer.
3. Contact an authorized service dealer
4. Contact an authorized service dealer.
1. Clean or replace air filter.
2. Check for dirty fuel filter; replace.
Check for kinked or split fuel line;
repair or replace.
1. Air filter dirty.
2. Fuel not reaching
carburetor.
Engine will not
accelerate,
lacks power, or
dies under a
load.
3. Clean or replace spark plug
and re-gap.
3. Spark plug fouled.
4. Contact an authorized service dealer.
4. Carburetor requires
adjustment.
5. Carbon build up.
6. Compression low.
5. Contact an authorized service dealer.
6. Contact an authorized service dealer.
1. Choke partially on.
1. Adjust choke.
Engine smokes
excessively.
2. Fuel mixture incorrect.
2. Empty fuel tank and refill with
correct fuel mixture.
3. Air filter dirty.
4. Carburetor requires
adjustment.
3. Clean or replace air filter.
4. Contact an authorized service dealer.
Engine runs hot.
1. See “Fueling Engine” in Operation
section.
1. Fuel mixture incorrect.
2. Replace with correct spark plug.
3. Contact an authorized service dealer.
2. Spark plug incorrect.
3. Carburetor requires
adjustment.
4. Contact an authorized service dealer.
4. Carbon build up.
-- 11 --
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMITED WARRANTY
Poulan PRO warrants to the original purchaser
not cover predelivery setup or normal adjust-
that each new Poulan PRO brand gasoline tool
or attachment is free from defects in material
and workmanship and agrees to repair or re-
place under this warranty any defective gaso-
line product or attachment as follows from the
original date of purchase:
ments explained in the instruction manual.
THIS WARRANTY GIVES YOU SPECIFIC
LEGAL RIGHTS, AND YOU MAY HAVE
OTHER RIGHTS WHICH VARY FROM
STATE TO STATE.
NO CLAIMS FOR CONSEQUENTIAL OR
OTHER DAMAGES WILL BE ALLOWED,
AND THERE ARE NO OTHER EXPRESS
WARRANTIES EXCEPT THOSE EX-
PRESSLY STIPULATED HEREIN.
SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WAR-
RANTY LASTS OR THE EXCLUSION OR
LIMITATIONS OF INCIDENTAL OR CONSE-
QUENTIAL DAMAGES, SO THE ABOVE
LIMITATIONS OR EXCLUSION MAY NOT
APPLY TO YOU.
The policy of Poulan PRO is to continuously im-
prove its products. Therefore, Poulan PRO re-
serves the right to change, modify, or discon-
tinue models, designs, specifications, and ac-
cessories of all products at any time without no-
tice or obligation to any purchaser.
2 YEARS - Parts and Labor, when used for
household purposes.
90 DAYS - Parts and Labor, when used for
commercial, professional, or income producing
purposes.
30 DAYS - Parts and Labor, if used for rental
purposes.
This warranty is not transferable and does not
cover damage or liability caused by improper
handling, improper maintenance, or the use of
accessories and/or attachments not specifically
recommended by Poulan PRO for this tool. Ad-
ditionally, this warranty does not cover tune-ups,
spark plugs, filters, starter ropes, starter springs,
cutting line, or rotating head parts that will wear
and require replacement with reasonable use
during the warranty period. This warranty does
U.S. EPA
EMISSION CONTROL WARRANTY STATEMENT
YOUR WARRANTY RIGHTS AND OB-
LIGATIONS: The U. S. Environmental Protec-
tion Agency and Poulan/WEED EATER are
pleased to explain the emissions control sys-
tem warranty on your year 2005 and later
smalloff--road engine. Poulan/WEED EATER
must warrant the emission control system on
your small off--road engine for the periods of
time listed below provided there has been no
abuse, neglect, or improper maintenance of
your small off--road engine. Your emission
control system includes parts such as the
carburetor and the ignition system. Where a
warrantable condition exists, Poulan/WEED
EATER will repair your small off--road engine
at no cost to you. Expenses covered under
warranty include diagnosis, parts and labor.
MANUFACTURER’S WARRANTY COV-
ERAGE: If any emissions relatedpart onyour
engine (as listed under Emissions Control
Warranty Parts List) is defective or a defect in
the materials or workmanship of the engine
causes the failure of suchan emissionrelated
part, the part will be repaired or replaced by
Poulan/WEED EATER. OWNER’S WAR-
RANTY RESPONSIBILITIES: As the small
off--road engine owner, you are responsible
for the performance of the required mainte-
nance listed in your instruction manual. Pou-
lan/WEED EATER recommends that you re-
tain all receipts covering maintenance on
your small off--road engine, but Poulan/
WEED EATER cannot deny warranty solely
for the lack of receipts or for your failure to en-
sure the performance of all scheduled main-
tenance. As the small off--road engine owner,
you should be aware that Poulan/WEED
EATER may deny you warranty coverage if
your small off--road engine or a part of it has
faileddue to abuse, neglect, improper mainte-
nance, unapproved modifications, or the use
of parts not made or approved by the original
equipment manufacturer. You are responsi-
ble for presenting your small off--road engine
to a Poulan/WEED EATER authorized repair
center as soon as a problem exists. Warranty
repairs should be completed in a reasonable
amount of time, not to exceed 30 days. If you
have any questions regarding your warranty
rights andresponsibilities, you shouldcontact
your nearest authorized service center or call
Poulan/WEED EATER at 1--800--554--6723.
WARRANTY COMMENCEMENT DATE:
The warranty period begins on the date the
small off--road engine is purchased.
LENGTH OF COVERAGE: This warranty
shall be for a period of two years from the ini-
tial date of purchase. WHAT IS COVERED:
REPAIR OR REPLACEMENT OF PARTS.
Repair or replacement of any warranted part
will be performed at no charge to the owner at
an approved Poulan/WEED EATER servic-
ing center. If you have any questions regard-
ing your warranty rights and responsibilities,
you should contact your nearest authorized
service center or call Poulan/WEED EATER
at 1--800--554--6723. WARRANTY PERIOD:
Any warranted part which is not scheduledfor
replacement as required maintenance, or
which is scheduled only for regular inspection
to the effect of “repair or replace as neces-
sary” shall be warranted for 2 years. Any war-
ranted part which is scheduled for replace-
ment as required maintenance shall be war-
ranted for the period of time up to the first
scheduled replacement point for that part.
-- 1 2 --
Download from Www.Somanuals.com. All Manuals Search And Download.
DIAGNOSIS: The owner shall not be
charged for diagnostic labor which leads to
the determination that a warranted part is de-
fective if the diagnostic work is performed at
an approved Poulan/WEED EATER servic-
ing center. CONSEQUENTIAL DAMAGES:
Poulan/WEED EATER may be liable for dam-
ages to other engine components caused by
the failure of a warranted part still under war-
ranty. WHAT IS NOT COVERED: All failures
caused by abuse, neglect, or improper main-
tenance are not covered. ADD -ON OR
MODIFIED PARTS: The use of add--on or
modified parts can be grounds for disallowing
a warranty claim. Poulan/WEED EATER is
not liable to cover failures of warranted parts
caused by the use of add--on or modified
parts. HOW TO FILE A CLAIM: If you have
any questions regarding your warranty rights
and responsibilities, you should contact your
nearest authorized service center or call Pou-
lan/WEED EATER at 1--800--554--6723.
WHERE TO GET WARRANTY SERVICE:
Warranty services or repairs shall be pro-
vided at all Poulan/WEED EATER service
centers. Call 1--800--554--6723. MAINTE-
NANCE, REPLACEMENT AND REPAIR
OF EMISSION RELATED PARTS: Any Pou-
lan/WEED EATER approved replacement
part used in the performance of any warranty
maintenance or repair on emission related
parts will be provided without charge to the
owner if the part is under warranty. EMIS-
SION CONTROL WARRANTY PARTS
LIST: Carburetor, Ignition System: Spark
Plug (covered up to maintenance schedule),
Ignition Module. MAINTENANCE STATE-
MENT: The owner is responsible for the per-
formance of all required maintenance as de-
fined in the instruction manual.
This engine is certified to be emissions compliant for the following use:
Moderate (50 hours)
Intermediate (125 hours)
Extended (300 hours)
-- 1 3 --
Download from Www.Somanuals.com. All Manuals Search And Download.
|