ESPA OL: P`GINA19
FRAN˙AISE : PAGE 39
Instruction 10" Compound
Manual Slide Miter Saw
MODEL3807
IMPORTANT
Please make certain that the person who is to
use this equipment carefully reads and
understands these instructions before starting
operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. _________________________________
Type______________________________________
Serial No.__________________________________
Part No. 897462-001
Download from Www.Somanuals.com. All Manuals Search And Download.
20. DANGER: KEEP HANDS AWAY FROM CUTTING AREA. Keep hands away from blades. Do not reach
underneath work while blade is rotating. Do not attempt to remove cut material when blade is moving.
CAUTION: Blades coast after being turned of.f
21. MAKE WORKSHOPCHILDPROOFwith padlocks, master switches, or by removing starter keys.
22. USE RECOMMENDED ACCESSORIES. The use of accessories and attachments not recommended by
Porter-Cable may cause hazards or risk of injury to persons.
23. NEVER STAND ON TOOL.Serious injury could occur if the tool is tipped or if the cutting tool is accidentally
contacted.
24. DIRECTION OF FEED.Feed work into a blade or cutter against the direction of rotation of the blade or cutter
only.
25. NEVER LEAVE TOOLRUNNING UNATTENDED. TURN POWER OFF.Dontleave tool until it comes to a
complete stop.
26. ALWAYS HOLD THE WORK FIRMLYagainst the fence and table. DO NOT perform any operation freehand.
27. WARNING:ALWAYSkeep hands out of path of saw blade. If the workpiece you are cutting would cause your
hand to be inside the table hazard area (see section TABLE HAZARD AREA ), the workpiece should be
clamped in place before making cut.
28. NEVERuse blades larger or smaller in diameter than recommended. Recommended size of blade is 10"in
diameter.
29. NEVER use blades recommended for operation at less than 6000 RPM.
30. USE the blade guard at all times.
31. NEVERreach around or behind saw blade.
32. TURN OFF SAW and MAKE SURE blade has come to a complete stop before removing or securing
workpiece, changing workpiece angle or changing the angle of the blade.
33. USE PROPER EXTENSION CORD.Make sure your extension is in good condition. When using an extension
cord, be sure to use one heavy enough to carry the current your product will draw.An undersized cord will cause
a drop in line voltage resulting in loss of power and overheating. The table in EXTENSION CORD SELECTION
shows the correct size to use depending on cord length and nameplate ampere rating of the tool. If in doubt, use
the next heavier gage. The smaller the gage number, the heavier the cord.
SAVE THESE INSTRUCTIONS
ADDITIONALSAFETYRULES FOR COMPOUND SLIDE MITER SAW S
1. WARNING: USE ONLYCROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES BE
SURE THE HOOK ANGLE IS 5 DEGREES OR LESS. DO NOT USE BLADES WITH DEEP GULLETS AS
THEYCAN DEFLECT AND CONTACT GUARD.
2. WARNING: Donot operate the miter saw until it is completely assembled and installedaccordingtotheinstructions.
3. IFYOU ARE NOTthoroughly familiar with the operation of compound slide miter saws, obtain advice from
your supervisor, instructor or other qualified person.
4. BE SURE blade is sharp, runs freely and is free of vibration.
5. ALLOWthe motor to come up to full speed before starting cut.
6. KEEPmotor air slots clean and free of chips.
7. ALWAYS MAKE SURE rotatingtable is tight before cutting, even if the table is positioned in one of the
positive stops.
8. BE SURE blade and flanges are clean and that arbor screw is tightened securely.
9. USE ONLY blade flanges specified for your saw.
10. NEVER apply lubricants to the blade when it is running.
11. ALWAYS CHECK the blade for cracks or damage before operation. Replace cracked or damaged blade
immediately.
12. ALWAYS KEEPthe lower blade guard in place and operating properly.
13. MAKE SURE blade is not contacting workpiece before switch is turned on.
14. NEVER LOCKthe switch in the O N position.
15. IMPORTANT:After completing cut, release power switch and wait for coasting blade to stop before returning
saw to raised position.
16. DO NOT remove jammed or cut-off pieces until blade has stopped.
17. NEVERcut ferrous metals or masonry.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
18. NEVER recut small pieces.
19. PROVIDE ADEQUATESUPPORTtothe sides of the saw table for long workpieces.
20. NEVER use the miter saw in an area with flammable liquids or gases.
21. NEVER USE SOLVENTS TO CLEAN PLASTIC PARTS. Solvents could possibly dissolve or otherwise
damage the material. Only a soft, damp cloth should be used to clean plastic parts.
22. DISCONNECT SAW from power source and clean the machine before leaving it.
23. MAKE SURE the work area is cleaned before leaving the machine.
24. ADDITIONALINFORMATIONregarding the safe and proper operation of this product is available from the
National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201, in the Accident Prevention Manual for
Industrial Operation and also in the Safety Data Sheets provided by the NSC. Please also refer to the American
National Standard Institute ANSI 01.1 Safety Requirements for the Woodworking Machinery and the U.S.
Department of Labor OSHA1910.213 Regulations.
25. SOME WOOD CONTAINS PRESERVATIVES WHICH CAN BE TOXIC.Take extra care to prevent inhalation
and skin contact when working with these materials. Request, and follow, any safety information available from
your material supplier.
26. DON T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges. Have damaged or worn power cord and strain reliever replaced immediately. DO NOT
ATTEMPTTO REPAIR POWER CORD.
27. WEAR EAR PROTECTIONtosafeguard against possible hearing loss.
28. AVOID CUTTING NAILS AND KNOTS.Inspect for and remove all nails from lumber before cutting. Trytodo
layout cuts between knots.
29. NEVER USE LIQUID COOLANT.Todosocould present electrical shock hazard.
30. KEEPCLEAR OF SAWDUST EJECTION CHUTE.Sawdust and chipsare expelled out the ejection chute at
rear of saw. Do not allow anyone in this area while saw is in operation.
31. WARNING:Slide cutting by PULLINGthe saw towards the operator can be dangerous, causing the saw to
kick upwards and towards the operator.Always PUSHthe saw forward, away from the operator, and towards the
fence when slide cutting.
32. WHEN USING THE SAW AS AMITER AND MAKING CHOPCUTS, MAKE SUREthe saw sliding mechanism
is locked in place to prevent the saw from kicking towards the operator.
33. WHEN THE MITER SAW IS NOT IN USE, the switch should be locked in the OFF position to prevent
unauthorized use of the saw.
REPLACEMENT PARTS
When servicing use only identical replacement parts.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60 cycle A.C. current and voltage
within plus or minus 5 percent of that shown on the specification plate of the tool. Several models, however,are
designed for A.C. current only. Refer to the specification plate on your tool for proper voltage and current rating.
CAUTION: Donot operate your tool on a current on which the voltage is not within correct limits. Do not
operate tools rated A.C. only on D.C. current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
sure the conductor size is large
enough to prevent excessive voltage
drop which will cause loss of power
and possible motor damage. A table of
recommended extension cord sizes
will be found in this section. This table
is based on limiting line voltage drop to
5 volts (10 volts for 230 volts) at 150%
of rated amperes.
Length of Cord in Feet
100 Ft. 150 Ft. 200 Ft. 250 Ft. 300 Ft. 400 Ft. 500 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft. 500 Ft. 600 Ft. 800 Ft. 1000 Ft.
115V
230V
25 Ft.
50 Ft.
50 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
If an extension cord is to be used
outdoors it must be marked with the
suffix W-A following the cord type
designation. For example SJTW-Ato
indicate it is acceptable for outdoor
use.
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
4
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATING INSTRUCTIONS
FOREWORD
Porter-Cable Model 3807 is a high capacity 10" compound miter saw designed to cut wood and non-ferrous
metals. It can crosscut 111…2"x33…16" and 9" x 37…8", miter at 45 both left and right 81…8"x33…16", and 63…8"x
37…8", bevel at 45 left111…2"x23…16" and 81…2"x25…8", compound 45 left miter and 45 bevel 81…8"x23…16" and
61…2"x25…8" and compound 45 right miter and bevel 81…8"x17…8" and 31…2"x25…8".
POWER CONNECTIONS
A separate electrical circuit should be used for your tools. If an extension cord is used, make sure the conductor
size is large enough to prevent excessive voltage drop which will cause loss of power and possible motor
damage. For distances up to 100 feet use #12 wire. For distances up to 150 feet use #10 wire. If an extension
cord is to be used outdoors it must be marked with the suffix W-A following the cord type designation. For
example SJTW-A toindicate it is acceptable for outdoor use. Replace damaged or worn cord immediately.
Before connecting the motor to the power line, make sure the switch is in the OFF position and be sure that
the electric current is of the same characteristics as stamped on motor nameplate.
CAUTION: Keep the extension cord away from the cutting area and position the cord so that it will not
be a tripping hazard or contact material being placed into or removed from the machine.
UNPACKING
1. Carefully remove the machine from the carton.
W e recommend you retain all packing materials until
after you have inspected and satisfactorily operated
the machine.
WARNING: Do not connect the machine to the
power source until you have read and
understood this entire instruction manual.
2. Place the machine on a firm, level surface where
there is plenty of room for handling and properly
supporting the workpiece.
3. Familiarize yourself with all features and controls
as explained in this manual.
4. The machine is shipped with the cuttinghead
locked in the down position and the table rotated to
Fig. 2
the 45 degree right miter position, Fig. 2. To release
the head and move it to the operating position see MOVING CUTTINGHEAD TO THE UP POSITION and
MOVING THE TABLE TO THE 90 DEGREE CUT-OFF POSITION inthis section.
5. Unassembled items are shown in Fig. 3 for identification and use in assembling the saw.
1
4
1 Dust Elbow
2 W ork Clamp
3 Dust Bag
2
3
4 Open End Wrench
Fig. 3
5
Download from Www.Somanuals.com. All Manuals Search And Download.
E
D
A
Fig. 5
Fig. 4
MOVING CUTTINGHEAD
TO THE REAR POSITION
1. MAKE CERTAIN THE MACHINE IS DISCON-
NECTED FROM THE POWER SOURCE.
2. Carefully remove cable tie (A) Fig. 4, which is
holding the cuttinghead in the down position.
E
3. To move the cuttinghead (D) Fig. 5, to the rear
position, loosen lock knob (E) and push cuttinghead (D)
to the rear position. Then tighten lock knob (E) Fig. 6.
4. Fig. 6, illustrates the cuttinghead locked in the rear
position.
Fig. 6
A
RAISING THE CUTTINGHEAD
B
1. While holding the cuttinghead (A) Fig. 7, down, pull
out and rotate cuttinghead lock knob (B) 90 degrees
untilpin(C)Fig. 8, isinthehorizontal position as shown.
The cuttinghead can then be raised.
2. Fig. 9 illustrates the cuttinghead (A) in the raised
position.
3. WARNING: Cutterhead lock knob (B) Fig. 7, is
designed to lock the cutterhead in the down position for
only storage or carrying. Never operate saw with the
cutterhead in the lock down position.
Fig. 7
A
C
B
Fig. 8
Fig. 9
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
WARNING: FOR YOUR OWN SAFETY, DO NOT CONNECT THE MITER SAW TO THE POWER
SOURCE UNTIL THE MACHINE IS COMPLETELY ASSEMBLED AND YOU HAVE READ AND
UNDERSTOOD THE ENTIRE OWNER S MANUAL.
D
C
A
A
B
Fig. 10
Fig. 11
ASSEMBLING DUST ELBOW AND DUST BAG
1. Insert smooth end of dust elbow (A) Fig. 10, into opening (B). The dust elbow (A) can be rotated as desired.
2. Compress spring clips(C) Fig. 11, on dust bag (D) and clip dust bag onto end of elbow (A) as shown.
MOVING TABLE TO THE 0 DEGREE CUT-OFF POSITION
1. Rotate locking knob (A) Fig. 12, counterclockwise to unlock. Depress lever (B) and rotatetable (C) to the 0
degree straight cut-off position, release lever (B) and tighten locking knob (A).
2. Fig. 13, illustrates the table (C) in the 0 degree straight cut-offposition.
3. For proper operation and adjustment of the table, refer to sections, ROTATING TABLE FOR MITER
CUTTING , ADJUSTING CLAMPING ACTION OF TABLE LOCKING MECHANISM and ADJUSTING
SLIDING FIT BETWEEN MOVABLE TABLE AND BASE.
C
C
A
B
Fig. 13
Fig. 12
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLING WORK CLAMP
1. Insert post (A) Fig. 14, of work clamp assembly (B)
down through hole in the base of the machine as shown
and lock in place by tightening lock knob (C). The work
clamp (B) Fig. 14, can be used on the right or leftsideof
the cuttinghead.
B
A
2. For proper operation of the work clamp, refer to
section WORK CLAMPOPERATION.
C
Fig. 14
STARTING AND STOPPING MACHINE
Tostart the machine, depress switch trigger (A) Fig. 15.
To stop the machine, release the switch trigger.
This saw is equipped with an automatic electric blade
brake. As soon as the switch trigger (A) Fig. 15, is
released, the electric brake is activated and stops the
blade in seconds.
A
DANGER: A TURNING SAW BLADE CAN BE
DANGEROUS. AFTER COMPLETING CUT,
RELEASE SWITCH TRIGGER (A) FIG. 15, TO
ACTIVATE BLADE BRAKE. KEEP CUTTING-
HEAD DOWN UNTIL BLADE HAS COME TO A
COMPLETE STOP.
Fig. 15
WARNING: THE TORQUE DEVELOPED DURING
BRAKING MAY LOOSEN THE ARBOR SCREW.
THE ARBOR SCREW SHOULD BE CHECKED
PERIODICALLY AND TIGHTENED IF
NECESSARY.
B
LOCKING SWITCH IN THE OFF
POSITION
IMPORTANT:When the miter saw is not in use, the
switch should be locked in the OFF position using a
padlock (B) Fig. 16, with a 3…16" diameter shackle to
prevent unauthorized use of the saw.
Fig. 16
ROTATING TABLE
FOR MITER CUTTING
1. Your compound slide saw will cut any angle from a
straight 0 degree cut to 57 degrees right and 47 degrees
left. Rotate locking knob (A) Fig. 17, counterclockwise,
depress lock lever (B), and move table to desired position.
2. The compound miter saw is equipped with positive
stops at the 0 degree cut-offposition and at the 15, 22.5,
31.62, and 45 degrees left and right positions.
B
A
Fig. 17
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING SLIDING FIT BETWEEN
MOVABLE TABLE AND BASE
CAUTION: DISCONNECT THE MACHINE FROM
THE POWER SOURCE.
A
If it ever becomes necessary to adjust the sliding fit
between the movable table and the base, turn nut (A)
Fig. 18, clockwise to increase or counterclockwise to
decrease the sliding fit. This adjustment should not be
too tight that it restricts the rotating movement of the
table or too loose that it affects the accuracy of the saw.
Fig. 18
ADJUSTING FENCE 90 DEGREES
TO BLADE
CAUTION: DISCONNECT THE MACHINE FROM
THE POWER SOURCE.
B
C
IMPORTANT: BEFORE MAKING THIS ADJUST-
MENT MAKE CERTAIN THE BLADE IS SET AT0
DEGREES TO THE TABLE. SEE SECTION
ADJUSTING 0 AND 45 DEGREE BEVEL
POSITIVE STOPS.
1. DISCONNECT THE SAW FROM THE POWER
SOURCE.
A
D
2. Rotate the movable table so that the blade is 90
degrees to the fence and the positive stop for the 0
degree mark on the scale is engaged.
Fig. 19
3. Using a square (A) Fig. 19, place one end of the
square against the front of the fence (B) and the other
end against the blade (C), with the blade in the down
position, as shown. Check to see if the fence is 90
degrees to the blade.
4. If an adjustment is necessary, the fence (B) Fig. 19,
can be adjusted by loosening the two screws, shown at
(D), that attach the fence to the base, using wrench
supplied. Adjust the fence (B) as required and tighten
the two screws (D).
G
F
5. After you are sure the fence is 90 degrees to the
blade, adjust the cursor (F) Fig. 20, so the pointer is
aligned with the 0 degree mark on the scale by
loosening screw (G), adjusting cursor (F) and tightening
screw (G).
Fig. 20
A
A
TABLE HAZARD AREA
WARNING: THE AREA INSIDE THE TWO RED
LINES (A) FIG. 21, ON THE TABLE IS
DESIGNATED AS A HAZARD ZONE. NEVER
PLACE YOUR HANDS INSIDE THIS AREA
WHILE THE TOOLIS BEING OPERATED.
Fig. 21
9
Download from Www.Somanuals.com. All Manuals Search And Download.
G
A
A
D
E
D
C
F
B
Fig. 22
Fig. 23
WORK CLAMPOPERATION
1. The height of the work clamp (A) Fig. 22, can be
adjusted by loosening lock knob (B) and moving post (C)
up or down, or depressing lock lever (D) and sliding clamp
body (E) up or down. After height of clamp (A) is adjusted,
tighten lock knob (B) and/or release lock lever (D).
G
A
2. During operation, lower clamp (A) Fig. 23, by
depressing lock lever (D), until the bottom of the clamp
(A) lightly contacts top of workpiece (F). IMPORTANT:
When lowering clamp (A) make certain cam lever
(G) is in the up position as shown.
F
3. For final clamping of the workpiece (F) Fig. 24,
against the table, lower cam lever (G) as shown. After
cut is completed, lift lever (G). This will raise clamp (A)
slightly, allowing you to slide or remove workpiece (F).
Fig. 24
TILTING CUTTINGHEAD FOR BEVELCUTTING
CAUTION:DISCONNECT THE MACHINE FROM THE POWER SOURCE.
1. The cuttinghead of your compound miter saw can be tilted to cut any bevel angle from a 90 degree straight
cut-off to a 45 degree left bevel angle by loosening bevel lock handle (A) Fig. 25, tilting cuttinghead (B) to the
desired angle, and tightening lock handle (A).
2. Positive stops are provided to rapidly position the saw blade at 90 and 45 degrees to the table. Refer to the
section of this manual titled Adjusting 90 and 45 degree bevel positive stops. The bevel angle of the cutting
arm is determined by the position of the pointer (C) Fig. 26, on scale (D).
3. In addition, an indicator (E) Fig. 26, is provided on the bevel scale at the 33.9 degree bevel angle for cutting
crown moulding. Refer to the CUTTING CROWN MOULDING section of this manual.
B
D
E
C
A
Fig. 25
Fig. 26
10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING SLIDING FIT BETWEEN
TRUNNION AND BEVELBRACKET
D
After a long period of time it may become necessary to
adjust the sliding fit between the trunnion (A) Fig. 27,
and the bevel bracket (B) by tightening adjusting nut
(C). NOTE: This adjustment must be made with the
bevel lock handle (D) loose. Correct adjustment is when
a good snug sliding fit is obtained between these two
parts. This adjustment should not be too tight that it
restricts the sliding movement or too loose that it affects
the accuracy of the saw cut.
B
C
A
Fig. 27
ADJUSTING 90 AND 45 DEGREE
BEVELPOSITIVE STOPS
1. DISCONNECT THE SAW FROM THE POWER
SOURCE.
2. Loosen bevel lock handle and move the
cuttinghead all the way to the right. Then tighten bevel
lock handle.
A
3. Using a square (A) Fig. 28, place one end of the
square on the table and the other end against the blade,
as shown. Check to see if the blade is at 90 degrees to
thetable.
4. If an adjustment is necessary, loosen bevel lock
handle. Then loosen locknut (B) Fig. 29, and turn
adjusting screw (C) until head of screw (C) contacts
inside of casting (D) when blade is 90 degrees to the
table. Then tighten locknut (B).
Fig. 28
5. When you are certain blade is 90 degrees to table,
loosen screw (J) Fig. 30, and adjust pointer (H) to line
up with the 0 degree mark on bevel scale (K).
G
C
6. Loosen bevel lock handle and move cuttinghead all
the way to the left bevel position and tighten bevel lock
handle.
B
E
7. Using a square (A) Fig. 31, check to see if the blade
is at 45 degrees to the table, as shown.
D
F
8. If an adjustment is necessary, loosen bevel lock
handle. Then loosen locknut (E) Fig. 29, and turn
adjusting screw (F) until head of screw (F) contacts
surface (G) when blade is 45 degrees to the table. Then
tighten locknut (E).
Fig. 29
9. These positive stops enable you to rapidly position
the blade at the most common bevel angles to the table, 90 and 45 degrees.
J
H
K
A
Fig. 30
Fig. 31
11
Download from Www.Somanuals.com. All Manuals Search And Download.
A
E
D
B
C
Fig. 32
Fig. 33
ADJUSTING BLADE GUARD
1. After an extended period of time, the movable blade guard (A) Fig. 32, might become sloppy and move
erratically when the cuttinghead is lowered. This can be easily corrected by slightly tightening nut (B) until the
lower blade guard (A) moves smoothly.
2. As soon as the cuttinghead begins to lower, the lower blade guard (A) Fig. 32, should begin to move. If it does
not, simply loosen screw (C) Fig. 33, and rotate eccentric (D) so that the eccentric (D) is contacting the actuating
arm (E) when the cuttinghead is in the top position. Then tighten screw (C).
ADJUSTING THE TENSION OF CUTTINGHEAD RETURN SPRING
The tension of the cuttinghead return spring has been adjusted at the factory in order that the cuttinghead returns to
the up position after a cut has been made. If it ever becomes necessary to re-adjust the spring tension, proceed as
follows: Turn adjusting screw (A) Fig. 34, clockwise to increase or counterclockwise to decrease the spring tension.
ADJUSTING SLIDING FIT BETWEEN CUTTINGHEAD ARM AND TRUNNION
After a long period of time it may become necessary to adjust the sliding fit between the cuttinghead arm (B) Fig.
34, and the trunnion (C) by tightening nut (D). Correct adjustment is when a good snug sliding fit is obtained
between these two parts.This adjustment should not be too tight that it restricts the sliding movement of the
cuttinghead arm (B) or too loose that it affects the accuracy of the saw cut.
ADJUSTING DOWNWARD TRAVEL
OF SAW BLADE
A
B
D
C
F
The downward travel of the saw blade was adjusted at the factory
to prevent the saw blade from contacting any metalsurfaces of the
machine. If an ajustment is ever necessary to limit the downward
travel of the saw blade for operations such as dado cutting (see
section of manual on DADO CUTTING ), loosen wing nut (E)
Fig. 34, and make adjustment by turning adjusting screw (F).
Tighten wing nut (E) after adjustment is completed.
E
H
J
L
K
G
LOCKING CUTTINGHEAD GUIDE RODS
The cuttinghead guide rods (G) Fig. 34, can be locked in place in
order to use the saw as a conventional miter saw (using the saw
as a chop saw instead of a sliding saw) by tightening lock knob
(H). When using the saw as a chop saw, the cuttinghead should
be all the way to the rear position before locking in place.
Fig. 34
ADJUSTING SLIDING FIT BETWEEN GUIDE RODS AND TABLE ASSEMBLY
To adjust the sliding fit between guide rods (G) Fig. 34, and table assembly (J), remove lock knob (H) and loosen
locknut (K). With wrenches provided, hold locknut (K) while turning adjusting nut (L) clockwise to increase or
counterclockwise to decrease the sliding action of the guide rods (G). This adjustment should not be too tight that
itrestricts the sliding movement of the rods or too loose that it affects the accuracy of the saw cut. When correct
adjustment is made, hold adjusting nut (L) and tighten locknut (K) with wrenches provided. Replace lock knob (H).
Periodically lubricate guide rods (G) using a light oil or spray lubricant to keep the guide rods (G) sliding smoothly.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
A
A
A
A
A
Fig. 35
Fig. 36
TOOLSTORAGE
A clip is provided on the rear of the saw and provides a convenient
storage area for wrench (A) Fig. 35, as shown.
FASTENING THE SAW TO A WORKBENCH
Before operating the saw, make sure it is firmly mounted to a workbench
or other supporting surface. Four holes (A) Fig. 36, are provided for
fastening the saw to a supporting surface.
USING THE SAW ON SAW HORSES
Fig. 37 illustrates the saw placed for use on saw horses. Notches in the
front and rear of the mounting feet are designed to fit conveniently on saw
horses.
Fig. 37
USING SAW WITH
2 X 4 EXTENSIONS
R
S
Fig. 38 illustrates the saw being
used with 2 x 4 extensions.
Note that notches in the front
and rear of the mounting feet
(K) are designed to fit and
fasten to the top of the two 2 x
4s(P). The length of the two 2
x4 s (P) can vary depending on
your preference. The distance
from the top of the 2 x 4 s(P)to
the saw table is 31…2". This
enables you to nail or fasten
standard 2 x 4 s (R) to the 2 x
4s (P), as shown. The top of
the 2 x 4 s (R) will then be in
alignment with the saw table,
providing support for long
workpieces. If desired, fence
extensions (S) made of 2 x 2 s
can be aligned with fence (T)
and bolted to 2 x 4 s(R).
P
P
T
R
S
P
K
P
K
Fig. 38
13
Download from Www.Somanuals.com. All Manuals Search And Download.
B
C
A
Fig. 39
Fig. 40
OPERATION
CORRECT OPERATING PROCEDURE FOR SLIDE CUTTING
WARNING: SLIDE CUTTING BY PULLING THE SAW TO WARDS THE OPERATOR CAN BE
DANGEROUS, CAUSING THE SAW TO KICK UPWARDS AND TO WARDS THE OPERATOR.
ALW AYS PUSHTHE SAW FORWARD, AWAY FROM THE OPERATOR, AND TO WARDS THE FENCE
WHEN SLIDE CUTTING.The following steps illustrate the proper operating procedure to follow when
slide cutting with your compound slide saw.
1. Place the workpiece (A) on the table and against the fence, as shown in Fig. 39. Grasp the cuttinghead handle
(B) but do not turn the saw on at this time.
2. Pull the cuttinghead (C) Fig. 40, toward you, with the cuttinghead in the up position. After the cuttinghead is
pulled toward you, compress switch trigger to turn the saw on, as shown.
3. Push down on the cuttinghead (C) Fig. 41, with the blade running, as shown.
4. Push the cuttinghead (C) Fig. 42, forward toward the fence, making the cut as shown.
C
C
Fig. 41
Fig. 42
5. Fig. 43 illustrates the completed cut. Release the switch trigger and keep the cuttinghead in the down position
until the blade (D) comes to a complete stop.
6. After the blade has stopped, raise the cuttinghead (C) to the up position, as shown in Fig. 44.
C
D
Fig. 43
Fig. 44
14
Download from Www.Somanuals.com. All Manuals Search And Download.
B
A
Fig. 45
Fig. 46
USING SAW AS A CHOPSAW
When cutting material that is narrow enough to allow the saw blade to cut through in a chopping motion (similar
to a conventional miter saw) instead of sliding the saw blade through the workpiece, the sliding action of the
saw must be locked in the rear position, as shown in Fig. 45, by tightening lock knob (A). The cuttinghead (B)
is pushed straight down to make the cut. After the cut is completed, release the switch trigger and let the blade
come to a complete stop before returning the cuttinghead to the up position.
DADO CUTTING
Dado cutting can easily be accomplished with your compound slide saw, as shown in Fig. 46, using a single saw
blade and moving the workpiece sideways the width of the saw blade after each cut. The cut is made in the
conventional way as explained in the section CORRECT OPERATING PROCEDURE and the downward travel
of the saw blade is adjusted for the depth of the dado as explained in the section ADJUSTING DOWNWARD
TRAVELOF SAW BLADE.
CUTTING CROWN MOULDING
One of the many features of your saw is the ease of cutting crown moulding. The following is an example of cutting
both inside and outside corners on 52…38 degree wall angle crown moulding.
NOTE:When cutting 45 degree wall angle crown moulding, the following procedure for inside and outside
corners is the same with the exception that the bevel position will always be at 30 degrees and the miter
position will be 351…4 degrees to the right or lef.t
1. Move the table to the 315…8 degree right miter position and lock the table in position.
NOTE:Apositive stop is provided to find this angle quickly.
2. Tilt the saw blade to the 337…8 degree left bevel position and tighten bevel lock handle.
NOTE:Atriangle indicator is provided on the bevel scale to find this angle quickly.
3. Place the crown moulding on the table with the CEILING EDGEofthe moulding against the fence, and make
the cut, as shown in Fig. 47.
C
E
D
E
A
B
Fig. 47
Fig. 48
15
Download from Www.Somanuals.com. All Manuals Search And Download.
D
B
A
C
Fig. 49
Fig. 50
NOTE: The piece of crown moulding used for the outside corner will always be on the right hand side of
the blade, as shown at (A) Fig. 47. The piece of crown moulding used for the inside corner will always be
on the left hand side of the blade, as shown at (B) Fig. 47. Note that the standard equipment work clamp
(E) is being used to hold the workpiece in position.
4. To make the matching halves of the inside and outside corners, simply rotate the table to the 315…8 degree
left miter position.
NOTE:Apositive stop is provided to find this angle quickly.The saw blade is already tilted to the 337…8
degree bevel position from the previous cut.
5. Place the crown moulding on the table with the W ALL EDGEofthe crown moulding against the fence and
make the cut. Again, the piece of crown moulding used for the outside corner will always be on the right side of
the blade, as shown at (C) Fig. 48. The piece of crown moulding used for the inside corner will always be on the
left side of the blade, as shown at (D) Fig. 48. Again, the standard equipment work clamp (E) is being used to
hold the workpiece in position.
6. Fig. 49 illustrates the two outside corner pieces; (A) being the piece cut at (A) Fig. 47, and (C) being the piece
cut at (C) Fig. 48.
7. Fig. 50 illustrates the two inside corner pieces; (B) being the piece cut at (B) Fig. 47, and (D) being the piece
cut at (D) Fig. 48.
MAINTENANCE
CHANGING THE BLADE
WARNING: USE ONLYCROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES
BE SURE THE HOOK ANGLE IS 5 DEGREES OR LESS. DO NOT USE BLADES WITH DEEP
GULLETS AS THEY CAN DEFLECT AND CONTACT GUARD. USE ONLY BLADES RATED FOR
OPERATION OF AT LEAST 6000 RPM WITH 5…8"ARBOR HOLES.
1. DISCONNECT THE SAW FROM THE POWER SOURCE.
2. Using the special wrench (A) Fig. 51, supplied, loosen screw (B) to free arbor cover (C).
3. Rotate arbor cover (C) Fig. 52, and lower guard (D) to the up position, as shown.
A
B
D
C
J
H
C
E
Fig. 51
Fig. 52
16
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Remove arbor screw (E) Fig. 52, by turning screw
(E) clockwise while at the same time pressing in on arbor
lock (F) Fig. 53, to keep arbor from turning. Remove
screw (E) Fig. 52, outside blade flange (H) and blade (J).
DO NOT REMOVE INSIDE BLADE FLANGE.
F
5. Make sure the inside surfaces of both the inside and
outside blade flanges are clean and free from any
foreign substance.
6. Make sure the inside blade flange is completely on
the arbor with the flats in the flange engaged with the
flats on the arbor.
7. Install new blade (J) Fig. 52, outside blade flange
(H) and arbor screw (E). Turn arbor screw (E)
counterclockwise to tighten while pressing in on arbor
lock (F) Fig. 53, to keep arbor from turning.
IMPORTANT:Make sure flats in outside blade flange
Fig. 53
(H) Fig. 52, are engaged with flats on arbor shaft and that teeth of saw blade (J) are pointing down at the front,
as shown in Fig. 52.
8. Rotate arbor cover (C) Fig. 51, until hook in cover is engaged under screw (B) and tighten screw (B) which
was loosened in STEP2.
BRUSH INSPECTION AND REPLACEMENT
CAUTION: BEFORE INSPECTING BRUSHES, DISCONNECT THE MACHINE FROM THE POWER
SOURCE.
Brush life varies. It depends on the load on the motor. Check the brushes after the first 100 hours of use for a new
machine, or after a new set of brushes has been installed.
After the first check, examine them after about 10 hours of use until such time that replacement is necessary.
The brush holders (A) Fig. 54, are located on the motor housing opposite each other. Fig. 55, illustrates one of
the brushes removed for inspection. When the carbon on either brush (B) is worn to 3…16" in length or if either
spring or shunt wire (C) is burned or damaged in any way, replace both brushes. If the brushes are found
serviceable after removing, reinstall them in the same position as removed.
A
C
B
Fig. 54
Fig. 55
17
Download from Www.Somanuals.com. All Manuals Search And Download.
KEEPTOOLCLEAN
Periodically blow out all air passages with dry compressed air. Clean all plastic parts with a soft damp cloth.
NEVER use solventstoclean plastic parts.They could possibly dissolve or otherwise damage the material.
CAUTION: WEAR SAFETYGLASSES WHILE USING COMPRESSED AIR.
FAILURE TO START
Shouldyourtoolfailtostart, check to make sure the prongs on the cord plug are making good contactintheoutlet.
Also, check for blown fuses or open circuit breakers in the line.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due to wear from normal use. These
operations should ONLY be performed by either an AUTHORIZED PORTER-CABLE SERVICE STATION or a
PORTER-CABLE SERVICE CENTER. All repairs made by these agencies are fully guaranteed against defective
material and workmanship. We cannot guarantee repairs made or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any time. In any communications, please
give all information shown on the nameplate of your tool (model number, type, serial number,etc.).
PORTER-CABLE LIMITED ONE YEAR WARRANTY
Porter-Cable warrantsits Professional Power Tools for a period of one year from the date of original purchase. Wewill repairor
replace, at our option, any part or parts of the product and accessories covered under this warranty which, after examination,
proves to be defective in workmanship or material during the warranty period. For repair or replacement, return the complete tool
or accessory, transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station. Proof of
purchase may be required. This warranty does not apply to repair or replacement required due to misuse, abuse, normal wear
and tear or repairs attempted or made by other than our Service Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE, WILLLASTONLYFOR ONE (1) YEAR FROM THE DATE OF PURCHASE.
Toobtain information on warranty performance please write to: PORTER-CABLE CORPORATION, 4825 Highway 45 North, P.O.
Box 2468, Jackson, Tennessee 38302-2468; Attention: Product Service. THE FOREGOING OBLIGATION IS PORTER-CABLE S
SOLE LIABILITYUNDER THIS OR ANYIMPLIED WARRANTYAND UNDER NO CIRCUMSTANCES SHALLPORTER-CABLE
BE LIABLE FOR ANY INCIDENTALOR CONSEQUENTIALDAMAGES. Some states do not allow limitations on how long an
implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion
may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary from state to state.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE)
(CENTRE DE SERVICE PORTER-CABLE)
Parts and Repair Service for Porter-Cable Power Tools are Available at These Locations
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable)
(Locations oø vous trouverez les piŁces de rechange nØcessaires ainsi qu un service d entretien)
ARIZONA
GEORGIA
MINNESOTA
Cleveland 44125
Forest Park 30297 (Atlanta)
5442 Frontage Road, Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Minneapolis 55429
4315 68th Avenue North
Phone: (612) 561-9080
Fax: (612) 561-0653
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ILLINOIS
Addison 60101 (Chicago)
311 Laura Drive
Phone: (630) 628-6100
Fax: (630) 628-0023
PENNSYLVANIA
MISSOURI
CALIFORNIA
W illow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
North Kansas City 64116
1141 SwiftAvenue
P.O. Box 12393
Phone: (816) 221-2070
Fax: (816) 221-2897
Ontario 91761 (Los Angeles)
3949AEast Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
W oodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
TENNESSEE
Nashville 37214
2262 Lebanon Pike
Phone: (615) 882-0320
Fax: (615) 882-0051
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
St. Louis 63119
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
MARYLAND
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
COLORADO
Denver 80216
5855 Stapleton Drive North
Suite A-140
Phone: (303) 370-6909
Fax: (303) 370-6969
TEXAS
Dallas 75220
10720 N. Stemmons Freeway
Phone: (214) 353-2996
Fax: (214) 350-3943
NEW YORK
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
MASSACHUSETTS
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Houston 77055
NORTH CAROLINA
Charlotte 28209
4303-B South Boulevard
Phone: (704) 525-4410
Fax: (704) 525-0618
FLORIDA
W est 10 Business Center
1008 Wirt Road, Suite 120
Phone: (713) 682-0334
Fax: (713) 682-4867
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
WASHINGTON
OHIO
Renton 98055 (Seattle)
268 Southwest 43rd Street
Phone: (425) 251-6680
Fax: (425) 251-9337
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
MICHIGAN
Tampa 33609
Troy 48083 (Detroit)
1355 Combermere
Phone: (248) 597-5000
Fax: (248) 597-5004
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or901-541-6042 for assistance locating one. Parts and accessories for
Porter-Cable products should be obtained by contacting any Porter-Cable Distributor,Authorized Service Center, or Porter-Cable Factory Service Center.Ifyou
do not have access to any of these, call 888-848-5175 and you will be directed to the nearest Porter-Cable Factory Service Center. Las Estaciones de Servicio
Autorizadas estÆn ubicadas en muchas grandes ciudades. Llame al 800-487-8665 al901-541-6042 para obtener asistencia a fin de localizar una. Las piezas
y los accesorios para los productos Porter-Cable deben obtenerse poniØndose en contacto con cualquier distribuidor Porter-Cable, Centro de Servicio Autorizado
o Centro de Servicio de FÆbrica Porter-Cable. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirÆn al Centro de Servicio de
FÆbrica Porter-Cable mÆs cercano. Des centres de service agrØØs sont situØs dans beaucoup de grandes villes. Appelez au 800-487-8665 ou au 901-541-6042
pour obtenir de l aide pour en repØrer un. Pour obtenir des piŁces et accessoires pour les produits Porter-Cable, s adresser tout distributeur Porter-Cable, centre
de service agrØØ ou centre de service d usine Porter-Cable. Si vous n avez accŁs aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le
centre de service d usine Porter-Cable le plus proche.
DELTA SERVICE CENTERS
MANITOBA
QU BEC
ALBERTA
1699 Dublin Avenue
W innipeg, Manitoba
R3H 0H2
Phone: (204) 633-9259
Fax: (204) 632-1976
1515 Ave.
Bay 6, 2520-23rd St.N.E.
Calgary,Alberta
T2E 8L2
Phone: (403) 735-6166
Fax: (403) 735-6144
St-Jean Baptiste,
QuØbec, QuØbec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby,B.C.
505 Southgate Drive
Guelph, Ontario
N1H 6M7
1447, Begin
St-Laurent, (MontrØal), QuØbec
H4R 1V8
V5A4T8
Phone: (519) 836-2840
Fax: (519) 767-4131
Phone: (514) 336-8772
Fax: (514) 336-3505
Phone: (604) 420-0102
Fax: (604) 420-3522
The following are trademarks of PORTER-CABLE Corporation (Las siguientes son marcas registradas de PORTER-CABLE S.A.) (Les marques suivantes sont des
marques de fabriquant de la PORTER-CABLE Corporation): BAMMERfi,LASERLOCfi, OMNIJIGfi, POCKET CUTTERfi, PORTA-BANDfi, PORTA-PLANEfi,
PORTER-CABLEfi, QUICKSANDfi, SANDTRAPfi,SAW BOSSfi, SPEED-BLOCfi, SPEEDMATICfi, SPEEDTRONICfi,STAIR-EASEfi,THE PROFESSIONALEDGEfi,
THE PROFESSIONAL SELECTfi,TIGER CUBfi,TIGER SAW fi,TORQ-BUSTERfi, VERSA-PLANEfi,WHISPER SERIESfi, DURATRONIC , FRAME SAW ,
INNOVATION THAT WORKS , JETSTREAM , MICRO-SET , MORTEN , NETWORK , RIPTIDE , TRU-MATCH , WOODWORKER S CHOICE .
Trademarks noted with fi are registered in the United States Patent and Trademark Office and may also be registered in other countries. Las Marcas Registradas
con el signo de fi son registradas por la Oficina de Registros y Patentes de los Estados Unidos y tambiØn pueden estar registradas en otros pa ses. Marques
dØposØes, indiquØes par la lettre fi, sont dØposØes au Bureau des brevets d invention et marques dØposØes aux Etats-Unis et pourraient Œtre dØposØes aux
autres pays.
Copyright ' 1999 PORTER-CABLE Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
Printed in U.S.A.
|