OPERATOR'S MANUAL
R161 ROUTER
DOUBLE INSULATED
SPECIFICATIONS:
Depth Of Cut
0 - 1-1/2 in. (0 - 38.1 mm)
1/4 in. (6.4 mm)
1-1/2 HP
Collet
Horsepower
Rating
120 Volts, 60Hz, AC Only
8.0
Amperes
No Load Speed
Net Weight
25,000 RPM
7.8 lbs. (3.5 kg)
THANK YOU FOR BUYING A RYOBI ROUTER.
Your new router has been engineered and manufactured to Ryobi's high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
CAUTION: Carefully read through this entire operator's manual before using your new router.
Pay close attention to the Rules for Safe Operation, Warnings, and Cautions. If you use your router properly and only for what
it is intended, you will enjoy years of safe, reliable service.
Thank you again for buying a Ryobi router.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and the
explanations with them, deserve your careful attention and understanding. The safety warnings do not by
themselves eliminate any danger. The instructions or warnings they give are not substitutes for proper
accident prevention measures.
SYMBOL
MEANING
SAFETY ALERT SYMBOL:
Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs.
DANGER: Failure to obey a safety warning will result in serious injury to yourself or to others. Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
WARNING:Failuretoobeyasafetywarningcanresultinseriousinjurytoyourselfortoothers.Always
follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CAUTION: Failure to obey a safety warning may result in property damage or personal injury to
yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and
personal injury.
NOTE:
Advises you of information or instructions vital to the operation or maintenance of the equipment.
DOUBLE INSULATION
IMPORTANT
Your Ryobi power tool is double insulated. This means you Servicing of a tool with double insulation requires extreme
areseparatedfromthetool'selectricalsystembytwocomplete care and knowledge of the system and should be performed
sets of electrical insulation. This extra layer of insulation is only by a qualified service technician. For service we suggest
intended to protect the user from electrical shock due to a you return the tool to your nearest RYOBI AUTHORIZED
break in the wiring insulation. All exposed metal parts are SERVICE CENTER for repair. When servicing use only
isolated from the internal metal motor components with identical Ryobi replacement parts.
protecting insulation. Double insulated tools do not need to
be grounded.
WARNING:
WARNING:
The double insulated system is intended to protect the
user from shock resulting from a break in the tool's
internal wiring. Observe all normal safety precautions
related to avoiding electrical shock.
Do not attempt to operate this tool until you have read
thoroughly and understand completely all instructions,
safety rules, etc. contained in this manual. Failure to
comply can result in accidents involving fire, electric
shock, or serious personal injury. Save operator's manual
and review frequently for continuing safe operation, and
instructing others who may use this tool.
WARNING:
WEAR YOUR
The operation of any router can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety
goggles or safety glasses with side shields and a full face shield when needed. We recommend
Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
SAFETY GLASSES
FORESIGHT IS BETTER
THAN NO SIGHT
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
Safe operation of this power tool requires that you read and
frees both hands to operate the tool.
understand this operator's manual and all labels affixed to
the tool. Safety is a combination of common sense, staying
alert, and knowing how your router works.
I DON'T OVERREACH. Keep proper footing and balance
at all times. Do not use on a ladder or unstable support.
I MAINTAIN TOOLS WITH CARE. Keep tools sharp and
clean for best and safest performance. Follow instructions
for lubricating and changing accessories.
READ ALL INSTRUCTIONS
I KNOW YOUR POWER TOOL. Read the operator's
manual carefully. Learn the applications and limitations
as well as specific potential hazards related to this tool.
I DISCONNECT ALL TOOLS. When not in use, before
servicing, or when changing attachments, bits, cutters,
etc., all tools should be disconnected from power supply.
I GUARD AGAINST ELECTRICAL SHOCK by preventing
body contact with grounded surfaces. For example: pipes,
radiators, ranges, refrigerator enclosures.
I AVOID ACCIDENTAL STARTING. Don't carry plugged-
in tools with finger on switch. Be sure switch is off when
plugging in.
I KEEP GUARDS IN PLACE and in working order.
I USE RECOMMENDED ACCESSORIES. The use of
I REMOVE ADJUSTING KEYS AND WRENCHES. Form
habit of checking to see that keys and adjusting wrenches
are removed from tool before turning it on.
improper accessories may cause risk of injury.
I CHECK DAMAGED PARTS. Before further use of the
tool, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting and any other conditions that may affect
its operation. A guard or other part that is damaged
should be properly repaired or replaced by an authorized
service center unless indicated elsewhere in this
instruction manual.
I KEEP THE WORK AREA CLEAN. Cluttered areas and
work benches invite accidents.
I DON'T USE IN DANGEROUS ENVIRONMENTS. Do not
use power tools near gasoline or other flammable liquids,
in damp or wet locations or expose them to rain. Keep
work area well lighted.
I KEEP CHILDREN AND VISITORS AWAY. All visitors
should wear safety glasses and be kept a safe distance
from work area. Do not let visitors contact tool or
extension cord.
I NEVER LEAVE TOOL RUNNING UNATTENDED.
TURN POWER OFF. Disconnect all tools when not in
use, before servicing, or when changing attachments,
wheels, etc.
I MAKE WORKSHOP CHILDPROOF with padlocks,
master switches, or by removing starter keys.
I DON'T FORCE THE TOOL. It will do the job better and
I DON'T ABUSE CORD. Never carry tool by the cord or
yank it to disconnect from receptacle. Keep cord from
heat, oil, and sharp edges.
safer at the rate for which it was designed.
I USE THE RIGHT TOOL. Do not force tool or attachment
to do a job for which it was not designed. Don't use tool
for purpose not intended; for example, a circular saw
should never be used for cutting tree limbs or logs.
I PROTECT YOUR LUNGS. Wear a face or dust mask if
operation is dusty.
I PROTECT YOUR HEARING. Wear hearing protection
I USE THE PROPER EXTENSION CORD. Make sure
your extension cord is in good condition. When using an
extension cord, be sure to use one heavy enough to carry
thecurrentyourproductwilldraw. Anundersizedcordwill
cause a drop in line voltage resulting in loss of power and
overheating. A wire gauge size (A.W.G.) of at least 14 is
recommended for an extension cord 50 feet or less in
length. A cord exceeding 50 feet is not recommended. If
in doubt, use the next heavier gauge. The smaller the
gauge number, the heavier the cord.
during extended periods of operation.
WARNING: Cutter coasts after turn off.
I ALWAYS WEAR SAFETY GLASSES WITH SIDE
SHIELDS. Everyday eyeglasses have only impact-
resistant lenses; they are NOT safety glasses.
I OUTDOOR USE EXTENSION CORDS. When tool is
used outdoors, use only extension cords suitable for
use outdoors. Outdoor approved cords are marked with
the suffix W-A. For example: SJTW-A or SJOW-A.
I WEAR PROPER APPAREL. Do not wear loose clothing,
neckties, or jewelry that can get caught in tool's moving
parts and cause personal injury. Nonslip footwear is
recommended when working outdoors. Wear protective
hair covering to contain long hair and keep it from being
drawn into nearby air vents.
I KEEP CUTTERS CLEAN AND SHARP. Sharp cutters
minimize stalling and kickback.
I KEEP HANDS AWAY FROM CUTTING AREA. Keep
hands away from cutters. Do not reach underneath work
while cutter is rotating. Do not attempt to remove material
while cutter is rotating.
I STORE IDLE TOOLS. When not in use, tools should be
stored in a high, dry place or locked-up and out of the
reach of children.
I NEVER STAND ON TOOL. Serious injury could occur if
tool is tipped or if the blade is unintentionally contacted.
I SECURE WORK. Use clamps or a vise to hold work
when practical. It is safer than using your hand and it
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
RULES FOR SAFE OPERATION
I NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
I POLARIZED PLUGS. To reduce the risk of electric shock,
this tool has a polarized plug (one blade is wider than the
other). This plug fits in a polarized outlet only one way. If
the plug does not fit fully in the outlet, reverse the plug. If
it still does not fit, contact a qualified electrician to install
the proper outlet. Do not change the plug in any way.
Normal sparking of the motor could ignite fumes.
I INSPECT EXTENSION CORDS PERIODICALLY and
replace if damaged.
I INSPECT TOOL CORDS PERIODICALLY and if
damaged, have repaired at your nearest authorized
service center. Stay constantly aware of cord location.
I WHEN USING THIS ROUTER WITH A ROUTER
TABLE, HELP PREVENT POSSIBLE SERIOUS INJURY
BY KEEPING THE CUTTER GUARDED AT ALL TIMES.
Use only UL listed router tables, with guards, that have
been designed for use on routers that are of this type,
size, and weight.
I KEEP HANDLES DRY, CLEAN, AND FREE FROM OIL
AND GREASE. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based
products or any strong solvents to clean your tool.
I STAY ALERT. Watch what you are doing and use
common sense. Do not operate tool when you are tired.
Do not rush.
I SAVE THESE INSTRUCTIONS. Refer to them frequently
and use them to instruct other users. If you loan someone
this tool, loan them these instructions also.
I DO NOT USE TOOL IF SWITCH DOES NOT TURN IT
ON AND OFF. Have defective switches replaced by an
authorized service center.
WARNING:
I INSPECT FOR and remove all nails from lumber before
Some dust created by power sanding, sawing, grinding,
drilling, and other construction activities contains
chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
routing.
I DO NOT OPERATE THIS TOOL WHILE UNDER THE
INFLUENCE OF DRUGS, ALCOHOL, OR ANY
MEDICATION.
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals, work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
I DO NOT USE TOOL UNDER "BROWNOUT" OR
OTHER LOW VOLTAGE CONDITIONS. Also, do not
use with any device that could cause the power supply
voltage to change.
DO NOT EXPOSE
TO RAIN OR USE IN
DAMP LOCATIONS
SAVE THESE INSTRUCTIONS
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
ELECTRICAL
EXTENSION CORDS
ELECTRICAL CONNECTION
When using a power tool at a considerable distance from the
power source, use an extension cord heavy enough to carry
the current that the tool will draw. An undersized extension
cord will cause a drop in line voltage, resulting in a loss of
power and causing the motor to overheat. Use the chart
provided below to determine the minimum wire size required
in an extension cord. Only round jacketed cords listed by
Underwriter's Laboratories (UL) should be used.
Your router has a precision built electric motor. It should be
connected to a power supply that is 120 volts, 60Hz, AC
only (normal household current). Do not operate this tool
on direct current (DC). A substantial voltage drop will cause
loss of power and the motor will overheat. If your tool does
not operate when plugged into an outlet, double-check the
power supply.
Length of Extension Cord
Wire Size (A.W.G.)
CAUTION:
Keepthecordawayfromthecuttingareaandpositionthe
cord so that it will not be caught on lumber, tools, or other
objects during cutting.
Up to 50
14
When working with the tool outdoors, use an extension cord
that is designed for outside use. This is indicated by the
letters WA on the cord's jacket.
Before using an extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
UNPACKING
Your router has been shipped completely assembled and
ready for use. Inspect it carefully to make sure no breakage
or damage has occurred during shipping. If any parts are
damaged or missing, contact your nearest dealer to obtain
replacement parts before attempting to operate router. A
wrench, operator's manual, and warranty registration are
also included.
WARNING:
If any parts are missing, do not operate your router until
the missing parts are replaced. Failure to do so could
result in possible serious personal injury.
I Carefully lift router from the carton and place it on a level
work surface.
WARNING:
I Do not discard the packing materials until you have
carefully inspected the router, identified all parts, and
satisfactorily operated your new router.
To prevent accidental starting or electrical shock that
could cause possible serious personal injury, assemble
all parts to your router before connecting it to power
supply. Router should never be connected to power
supply when you are assembling parts, making
adjustments, lubricating, installing or removing cutters,
cleaning, or when not in use.
Note: If any parts are damaged or missing, do not attempt to
plug in the power cord and turn the switch on until the
damaged or missing parts are obtained and are installed
correctly.
Look for this symbol to point out important safety precautions.
It means attention!!! Your safety is involved.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
FEATURES
KNOW YOUR ROUTER
WARNING:
See Figure 1.
Before attempting to use your router, familiarize yourself
with all operating features and safety requirements.
Always wear safety goggles or safety glasses with side
shields when operating your router. Failure to do so could
result in dust, shavings, loose particles or foreign objects
being thrown into your eyes, causing possible serious
injury.
WARNING:
Do not allow familiarity with your router to make you
careless. Remember that a careless fraction of a second
is sufficient to inflict severe injury.
LOCK-ON BUTTON
The switch of your router is equipped with a "lock-on" feature
which is convenient when operating for extended periods of
time. To lock on, depress the trigger, push in the lock button
located on the side of the handle, then while holding the lock
button pushed in, release the trigger. To release the lock,
depress the trigger and release it. See Figure 1.
CHIP SHIELD
A clear plastic chip shield is installed on the front of your
routerforprotectionagainstflyingdustandchips. Theshield
is designed to fit the front opening of the router base. See
Figure 1. If necessary to remove chip shield, squeeze the
tabs on each end and pull outward. To replace, squeeze the
tabs at each end, fit into opening, then release.
Note: For your protection, do not use router without chip
shield properly in place.
UPSIDE DOWN VIEW OF ROUTER
DEPTH
INDICATOR
RING(S)
INDICATOR
POINT(S)
64
3
7
32
1
SPINDLE
LOCK
32
15
0
64
1
64
LOCK-ON
BUTTON
INDICATOR
POINT(S)
DEPTH
ADJUSTING
RING
1
3
3
64
3
3 16
7 64
1
1
64
1 8
9 64
HANDLE
DEPTH
INDICATOR
RING(S)
POWER
HANDLE
CLAMPING
LEVER
DEPTH
ADJUSTING RING
SWITCH
TRIGGER
CHIP
SHIELD
SUBBASE WITH
STRAIGHT EDGE
FRONT VIEW OF ROUTER
REAR VIEW OF ROUTER
Fig. 1
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
SPINDLE LOCK
WARNING:
Your router should never be connected to a power supply
when you are assembling parts, making adjustments,
installing or removing cutters, or when not in use.
Disconnecting your router will prevent accidental starting
that could cause serious injury.
1
3
1
INSTALLING/REMOVING CUTTERS
See Figures 2 and 3.
2
3
2
I Unplug your router.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
TO UNLOCK
SPINDLE
TO LOCK
SPINDLE
Fig. 2
CUTTER
COLLET
NUT
WRENCH
CAUTION:
To prevent damage to the spindle or spindle lock, always
allow motor to come to a complete stop before engaging
spindle lock.
TO LOOSEN
COLLET NUT
6
I A spindle lock is located on the top of the end cap. See
Figure 2. To activate lock: (1) push the spindle lock in,
(2) slide into lock position then, (3) release the spindle
lock.
4
0
1
5
64
7
3
2
I Place your router upside down on a table, then turn the
collet nut with a wrench until the lock mechanism inter-
locks. See Figure 3.
TO TIGHTEN
COLLET NUT
Fig. 3
Note: Spindle lock is spring loaded and will snap into
position when lock mechanism interlocks.
WARNING:
WARNING:
Do not use cutters with undersized shanks. Undersized
shanks will not tighten properly and could be thrown from
the tool causing injury.
If you are changing a cutter immediately after use, be
careful not to touch the cutter or collet with your hands or
fingers. They will get burned because of the heat buildup
from cutting. Always use the wrench provided.
WARNING:
I Remove cutters by turning collet nut counterclockwise
enough to allow cutter to slip easily from collet. See
Figure 3. The collet is machined to precision tolerances
to fit cutters with 1/4 in. (6 mm) diameter shank size.
Before connecting your router to a power supply, always
check to be sure the switch is not in "lock-on" position.
Failure to do so could result in accidental starting of your
router resulting in possible serious injury.
I With your router still upside down on a table, insert
shank of cutter into the collet. The shank of your cutter
should be close to but not touching the bottom of collet.
I Tighten the collet nut securely by turning clockwise with
the wrench provided. See Figure 3. Put spindle lock
back in unlock position. Otherwise, the interlocking
mechanism of the spindle lock will not let you turn your
router on. To unlock spindle: (1) push spindle lock in, (2)
slide into unlock position then, (3) release spindle lock.
See Figure 2.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
DEPTH OF CUT ADJUSTMENTS
DEPTH
INDICATOR
RING
See Figures 4, 5, 6, and 7.
We recommend that cuts be made at a depth not exceeding
1/8 in. (3 mm) and that several passes be made to reach
depths of cut greater than 1/8 in. (3 mm).
INDICATOR
POINT
I Unplug your router.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
I Place your router on a flat surface, unlock clamping
lever, and turn depth adjusting ring until cutter is inside
subbase. See Figures 4 and 5.
DEPTH
ADJUSTING
RING
I Turn the depth adjusting ring until tip of cutter touches
flat surface (zero depth of cut). See Figure 6. Next turn
depth indicator ring until the zero lines up with the indi-
cator point on front of motor housing. See Figure 5.
CUTTER
INSIDE SUBBASE
Fig. 5
SUBBASE
I Position your router so that the cutter can extend below
the subbase for desired depth setting.
I Turn the depth adjusting ring to obtain the desired depth
of cut. The distance the cutter moves can be read on the
depth adjusting ring. Each mark on the depth adjusting
ring indicates 1/64 in. (0.4 mm) change in depth setting.
One indicator point is located on front of the motor
housing, the other one is located on the base.
I Lock clamping lever, securing depth adjusting ring to
motor housing and base.
DEPTH OF CUT ADJUSTMENTS WHEN ROUTER
IS MOUNTED TO A ROUTER TABLE
See Figure 7.
The depth of cut is readable from both sides of the depth
adjusting ring. There is a depth indicator ring and indicator
point on both sides of the depth adjusting ring. The bottom
ring is convenient when using your router mounted to a
router table. The indicator point on the base should also be
used when using your router mounted to a router table.
CUTTER AT
ZERO DEPTH OF CUT
Fig. 6
FOR ROUTER TABLE USE ONLY
The depth indicator rings are identical parts. Therefore,
when you have your router mounted upside down on a
router table, you set depth of cut by reading the scale
different. Set the cutter at zero depth of cut, rotate depth
indicator ring to desired depth of cut on the scale, then turn
depth adjusting ring back to zero depth of cut and lock
clamping lever securely.
CLAMPING
LEVER
TO
LOCK
C
K
O
L
BASE
U
K
N
C
L
O
DEPTH
INDICATOR
RING
INDICATOR
POINT
TO
UNLOCK
Fig. 7
Fig. 4
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
For ease of operation and maintaining proper control, your
router has two handles, one on each side of the router base.
When using your router hold it firmly with both hands as
shown in Figure 8. Turn router on and let motor build to its full
speed, then gradually feed cutter into workpiece. Remain
alert and watch what you are doing. Do not operate router
when fatigued.
PROPER FEEDING
The right feed is neither too fast nor too slow. It is the rate at
which the bit is being advanced firmly and surely to produce
a continuous spiral of uniform chips — without hogging into
thewoodtomakelargeindividualchipsor,ontheotherhand,
to create only sawdust. If you are making a small diameter,
shallow groove in soft, dry wood, the proper feed may be
about as fast as you can travel your router along your guide
line. On the other hand, if the bit is a large one, the cut is deep
or the wood is hard to cut, the proper feed may be a very slow
one. Then, again, a cross-grain cut may require a slower
pace than an identical with grain cut in the same workpiece.
Fig. 8
There is no fixed rule. You will learn by experience. . . by
listening to the router motor and by feeling the progress of
each cut. If at all possible, always test a cut on a scrap piece
of the workpiece wood, beforehand.
TOO FAST
RATE OF FEED
IMPORTANT: The whole "secret" of professional routing
and edge shaping lies in making a careful setup for the cut
to be made and in selecting the proper rate of feed.
FORCE FEEDING
Clean, smooth routing and edge shaping can be done only
when the bit is revolving at a relatively high speed and is
taking very small bites to produce tiny, cleanly severed
chips. If your router is forced to move forward too fast, the
RPM of the bit becomes slower than normal in relation to its
forward movement. As a result, the bit must take bigger bites
as it revolves. “Bigger bites” mean bigger chips, and a
rougher finish. Bigger chips also require more power, which
could result in the router motor becoming overloaded.
TOO SLOW
Fig. 9
be advanced. If the wood is very hard, knotty, gummy or
damp, the operation must be slowed still more.
You can always detect “force feeding” by the sound of the
motor. Its high-pitched whine will sound lower and stronger
as it loses speed. Also, the strain of holding the tool will be
noticeably increased.
Under extreme force-feeding conditions the relative RPM of
the bit can become so slow—and the bites it has to take so
large—that chips will be partially knocked off (rather than
fully cut off), with resulting splintering and gouging of the
workpiece. See Figure 9.
TOO SLOW FEEDING
It is also possible to spoil a cut by moving the router forward
too slowly. When it is advanced into the work too slowly, a
revolving bit does not dig into new wood fast enough to take
abite;instead, itsimplyscrapesawaysawdust-likeparticles.
Scraping produces heat, which can glaze, burn, or mar the
cut— in extreme cases, can even overheat the bit so as to
destroy its hardness.
Your router is an extremely high-speed tool (25,000 RPM
no-load speed), and will make clean, smooth cuts if allowed
to run freely without the overload of a forced (too fast) feed.
Three things that cause “force feeding” are bit size,
depth-of-cut, and workpiece characteristics. The larger the
bit or the deeper the cut, the more slowly the router should
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
DEPTH
OF CUT
WIDTH
OF CUT
TOO SLOW FEEDING (Continued)
In addition, it is more difficult to control a router when the bit
is scraping instead of cutting. With practically no load on the
motor the bit will be revolving at close to top RPM, and will
have a much greater than normal tendency to bounce off the
sides of the cut (especially, if the wood has a pronounced
grain with hard and soft areas). As a result, the cut produced
may have rippled, instead of straight sides. See Figure 9.
Fig. 10
2ND. PASS
1ST.
PASS
1ST. PASS
2ND.
PASS
“Too-slow feeding” can also cause your router to take off in
a wrong direction from the intended line of cut. Always
grasp and hold your router firmly with both hands when
routing.
Fig. 11
You can detect “too-slow feeding” by the runaway too-highly
pitched sound of the motor; or by feeling the “wiggle” of the
bit in the cut.
GUIDE OUTSIDE
DEPTH OF CUT
ROTATION
THRUST
As previously mentioned, the depth of cut is important
because it affects the rate of feed which, in turn, affects the
quality of a cut (and, also, the possibility of damage to your
router motor and bit). A deep cut requires a slower feed than
a shallow one, and a too deep cut will cause you to slow the
feed so much that the bit is no longer cutting, it is scraping,
instead.
ROTATION
FEED
GUIDE
Making a deep cut is never advisable. The smaller bits—
especially those only 1/16 in. (1.6 mm) in diameter—are
easily broken off when subjected to too much side thrust. A
large enough bit may not be broken off, but if the cut is too
deep a rough cut will result— and it may be very difficult to
guide and control the bit as desired. For these reasons, we
recommend that you do not exceed 1/8 in. (3 mm) depth of
cut in a single pass, regardless of the bit size or the softness
or condition of the workpiece. See Figure 10.
GUIDE
FEED
ROTATION
THRUST
GUIDE INSIDE
Fig. 12
To make deeper cuts it is therefore necessary to make as
many successive passes as required, lowering the bit 1/8 in.
(3 mm) for each new pass. In order to save time, do all the
cutting necessary at one depth setting, before lowering the
bit for the next pass. This will also assure a uniform depth
when the final pass is completed. See Figure 11.
bit strike a knot, hard grain, foreign object, etc. that would
affect the normal progress of the cutting action, there will be
a slight kickback—sufficient to spoil the trueness of your cut
if you are not prepared. Such a kickback is always in the
direction opposite to the direction of bit rotation.
To guard against such a kickback, plan your setup and
direction of feed so that you will always be thrusting the
tool—to hold it against whatever you are using to guide the
cut—in the same direction that the leading edge of the bit is
moving.Inshort,thethrustshouldbeinadirectionthatkeeps
the sharp edges of the bit continuously biting straight into
new (uncut) wood.
DIRECTION OF FEED AND THRUST
Theroutermotorandbitrevolveinaclockwisedirection.This
gives the tool a slight tendency to twist (in your hands) in a
counterclockwise direction, especially when the motor revs
up (as at starting).
Because of the extremely high speed of bit rotation during a
“proper feeding” operation, there is very little kickback to
contend with under normal conditions. However, should the
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
ROUTER
WORK
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
ROUTING
Whenever you are routing a groove, your travel should be in
a direction that places whatever guide you are using at the
right-hand side. In short, when the guide is positioned as
shown in the first part of Figure 12, tool travel should be left
to right and counterclockwise around curves. When the
guide is positioned as shown in the second part of Figure 12,
tool travel should be right to left and clockwise around
curves. If there is a choice, the first setup is generally the
easiest to use. In either case, the sideways thrust you use is
against the guide.
PILOT
GUIDE
TOP EDGE SHAPING
ROUTER
WORK
STARTING AND ENDING A CUT
INTERNAL ROUTING
PILOT
Tilt router and place on workpiece, letting edge of subbase
contact workpiece first. Be careful not to let router bit contact
workpiece. Turn router on and let motor build to its full speed.
Gradually feed cutter into workpiece until subbase is level
with workpiece.
WHOLE EDGE SHAPING
Fig. 13
will make less than a full cut — which will alter the shape of
the finished edge.
Upon completion of cut, turn motor off and let it come to a
complete stop before removing router from work surface.
Note: Any of the piloted bits can be used without a pilot for
edge shaping with guides, as preceding. The size (diameter)
of the pilot that is used determines the maximum cut width
that can be made with the pilot against the workpiece edge.
The small pilot exposes all of the bit; the large one reduces
this amount by 1/16 in. (1.6 mm).
WARNING:
Never pull router out of work and place upside down on
work surface before the cutter stops. Failure to do so
could result in possible serious injury.
EDGE ROUTING
Place router on workpiece, making sure the router bit does
not contact workpiece. Turn router on and let motor build to
its full speed. Begin your cut, gradually feeding cutter into
workpiece.
EDGING WITH PILOT BITS
The arbor-type bits with pilots are excellent for quick, easy,
edge shaping of any workpiece edge that is either straight or
curved at a curvature as great or greater than the radius of
the bit to be used. The pilot prevents the bit from making too
deep a cut; and holding the pilot firmly in contact with the
workpiece edge throughout prevents the cut from becoming
too shallow.
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
Whenevertheworkpiecethicknesstogetherwiththedesired
depth of cut (as adjusted by router depth setting) are such
that only the top part of the edge is to be shaped (leaving at
least a 1/16 in. (1.6 mm) thick uncut portion at bottom), the
pilot can ride against the uncut portion, which will serve to
guide it. See Figure 13. However, if the workpiece is too thin
or the bit set too low so that there will be no uncut edge to ride
the pilot against, an extra board to act as a guide must be
placed under the workpiece. This “guide” board must have
exactly the same contour—straight or curved—as the
workpiece edge. If it is positioned so that its edge is flush with
the workpiece edge, the bit will make a full cut (in as far as
the bit radius). On the other hand, if the guide is positioned
as shown in Figure 13 (out from the workpiece edge), the bit
Upon completion of cut, turn motor off and let it come to a
complete stop before removing router from work surface.
WARNING:
Never pull router out of work and place upside down on
work surface before the cutter stops. Failure to do so
could result in possible serious injury.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING:
Keep a firm grip on router with both hands at all times.
Failure to do so could result in loss of control leading to
possible serious injury.
FREEHAND ROUTING
See Figure 14.
When used freehand, your router becomes a flexible and
versatile tool. This flexibility makes it possible to easily rout
signs, relief sculptures, etc.
Therearetwobasictechniquesforfreehandrouting:
I Routing letters, grooves, and patterns into wood. See
Figure 14.
I Routing out the background, leaving the letters or pattern
raised above the surface.
When freehand routing, we suggest the following:
I Draw or layout the pattern on workpiece.
I Choose the appropriate cutter.
FREEHAND ROUTING
Fig. 14
Note: A core box or V-groove bit is often used for
routing letters and engraving objects. Straight bits and
ball mills are often used to make relief carvings. Veining
bits are used to carve small, intricate details.
I Rout the pattern in two or more passes. Make the first
pass at 25 percent of the desired depth of cut. This will
provide better control as well as being a guide for the
next pass.
1
3
3
6
4
3
3
16
4
6
7
I Do not rout deeper than 1/8 in. (3 mm) per pass or cut.
8
1
5
3
2
4
6
9
WARNING:
Do not use large router bits for freehand routing. Use of
large router bits when freehand routing could cause loss
of control or create other hazardous conditions that could
cause possible serious personal injury.
ROUTINGWITHSTRAIGHTEDGEOFSUBBASE
See Figure 15.
The subbase on your router has a straight edge. It should be
used when placing your router against an edge guide or
fence and routing grooves parallel to the fence.
ROUTING WITH STRAIGHT EDGE OF
SUBBASE AGAINST AN EDGE GUIDE
Fig. 15
WARNING:
ALWAYS make sure the shank of the router bit is seated
within 1/16 in. of the bottom of the collet. Extending the
shank of the router bit more than 1/16 in. beyond the
base of the collet could cause improper engagement of
the collet to the bit and result in serious personal injury.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
#10-32 PAN HEAD
SCREW
5/16-18 X 3/4 IN.
FLATHEAD SCREW
BASE
BASE
SUBBASE
Fig. 16
Fig. 17
WARNING:
WARNING:
Do not use with router tables that fail to conform to safe
wood working practices and offer proper guarding for the
cutter. Failure to comply can result in an accident causing
possible serious injury.
Use only 5/16-18 x 3/4 in. machine screws to mount the
router in an inverted position for table use. The use of
smaller screws, such as the #10-32 machine screws
provided for mounting the subbase, could provide an
insecure mounting and result in the risk of serious
personal injury.
ROUTER TABLE USE
See Figures 16 and 17.
I Your router can be used on UL listed router tables such
as the Ryobi BT3000SXI Precision Cutting System. It
may be necessary to remove the subbase to utilize the
full pattern of some edge forming bits such as Roman
Ogee and round-over bits. Remove the four (4) #10-32
pan head screws and subbase. With the subbase base
removed, the router is secured to the mounting plate
with 5/16-18 x 3/4 in., tapered flat head screws provided
in the Ryobi Router Mounting Kit model number 4950300
or available at your local hardware store.
WARNING:
When using a UL listed router table, large router bits
should be used for edging only. Do not use router bits that
are larger in diameter than the opening in router base for
any purpose. Failure to heed this warning could result in
serious personal injury.
MAINTENANCE
WARNING:
WARNING:
When servicing use only identical Ryobi replacement
parts. Use of any other parts may create a hazard or
cause product damage.
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc. come in contact
with plastic parts. They contain chemicals that can
damage, weaken, or destroy plastic.
WARNING:
Failure to unplug your router could result in accidental
starting causing serious injury.
Whenelectrictoolsareusedonfiberglassboats, sportscars,
wallboard, spackling compounds, or plaster, it has been
found that they are subject to accelerated wear and possible
premature failure, as the fiberglass chips and grindings are
highly abrasive to bearings, brushes, commutators, etc.
Consequently, it is not recommended that this tool be used
for extended work on any fiberglass material, wallboard,
spackling compounds, or plaster. During any use on these
materials, it is extremely important that the tool is cleaned
frequently by blowing with an air jet.
GENERAL
Avoidusingsolventswhencleaningplasticparts.Mostplastics
are susceptible to damage from various types of commercial
solvents and may be damaged by their use. Use clean cloths
to remove dirt, carbon dust, etc.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
PROPER CARE OF CUTTERS
WARNING:
Get faster more accurate cutting results by keeping cutters
clean and sharp. Remove all accumulated pitch and gum
from cutters after each use.
Always wear safety goggles or safety glasses with side
shieldswhenoperatingyourrouter. Failuretodosocould
result in dust, shavings, loose particles or foreign objects
being thrown into your eyes, causing possible serious
injury.
When sharpening cutters, sharpen only the inside of the
cutting edge. Never grind the outside diameter. Be sure
when sharpening the end of a cutter to grind the clearance
angle the same as originally ground.
PROPER CARE OF COLLET
LUBRICATION
From time to time, it also becomes necessary to clean your
collet and collet nut. To do so, simply remove collet nut from
collet and clean the dust and chips that have collected. Then
return collet nut to its original position. Do not tighten collet
nut on collet without a cutter installed.
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normaloperatingconditions. Therefore,nofurtherlubrication
is required.
HELPFUL HINTS
I Always clamp workpiece securely before routing.
I A safe operator is one who thinks ahead.
I Always wear eye protection when routing.
I Make setup adjustments carefully. Then double check. Measure twice and cut once.
I Keep cutters clean and properly sharpened.
I Don’t let familiarity make you careless.
I Study all safety rules and do the job safely.
I NEVER place your hands in jeopardy.
IIIIMake certain clamps can’t loosen while in use.
I Test difficult setups on scrap — Don’t waste lumber.
I Plan each operation before you begin.
I Clean your router frequently. This will provide smoother operation of depth adjusting ring and clamping lever areas.
Shake router or blow with an air jet to remove sawdust buildup.
I THINK SAFETY BY THINKING AHEAD.
OPTIONAL ACCESSORIES
The following recommended accessories are current and were available at the time this manual was printed:
ITEM NO.
DESCRIPTION
4070175
4070176
6090080
Template Guide Adapter For Ryobi Template Guides
Template Guide Adapter For Porter Cable Rockwell and B&D Template Guides
Straight Guide For Ryobi Routers - Model Nos. R160, R161, R165, R175, R180, RE170,
RE170VS, RE175, and RE185
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATOR'S MANUAL
R161 ROUTER
DOUBLE INSULATED
EXTENSION CORD CAUTION
**Ampere rating
(on tool data plate) 0-2.0
2.1-3.4 3.5-5.0 5.1-7.0 7.1-12.0 12.1-16.0
When using a power tool at a considerable distance from a power
source, be sure to use an extension cord that has the capacity to
handle the current the tool will draw. An undersized cord will
cause a drop in line voltage, resulting in overheating and loss of
power. Use the chart to determine the minimum wire size re-
quired in an extension cord. Only round jacketed cords should be
used.
Cord Length
Wire Size (A.W.G.)
25'
50'
16
16
16
16
16
16
16
14
14
14
14
12
CAUTION: Keep the extension cord clear of the working
area. Position the cord so that it will not get caught on workpiece,
tools, or other obstructions while you are working with a power
tool.
When working with a tool outdoors, use an extension cord that is
designed for outside use. This is indicated by the letters "WA" on
the cord's jacket.
**Used on 12 gauge - 20 amp circuit.
Before using any extension cord, inspect it for loose or exposed
wires and cut or worn insulation.
• SERVICE
Now that you have purchased your tool, should a need ever exist for repair parts or
service, simply contact your nearest Ryobi Authorized Service Center. Be sure to
provide all pertinent facts when you call or visit. Please call 1-800-525-2579 for your
nearest Ryobi Authorized Service Center. You can also check our web site at
• MODEL NO.
The model number and serial number of your tool will be found on a plate attached to
the motor housing. Please record the model number and serial number in the space
provided below.
•
•
MODEL NUMBER
SERIAL NUMBER
R161
RYOBI TECHNOLOGIES, INC.
1428 Pearman Dairy Road Anderson SC 29625
Post Office Box 1207
Anderson SC 29622-1207
Phone 1-800-525-2579
972000-891
6-01
Printed in U.S.A.
Download from Www.Somanuals.com. All Manuals Search And Download.
|