ESPAÑOL : PÁGINA 15
FRANÇAISE : PAGE 3131
Instruction
manual
Double Insulated
Circular Saw
MODELS
423MAG and 424MAG
IMPORTANT
Please make certain that the person who is
to use this equipment carefully reads and
understands these instructions before
starting operations.
To learn more about Porter-Cable
visit our website at:
The Model and Serial No. plate is located on the main
housing of the tool. Record these numbers in the
spaces below and retain for future reference.
Model No. ______________________________________
Type ___________________________________________
Serial No._______________________________________
Copyright © 2004 Porter-Cable Corporation
Part No. 912490 - 05-12-04
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
4. Do not abuse the cord. Never use the cord to carry the tools or pull
the plug from an outlet. Keep cord away from heat, oil, sharp edges or
moving parts. Replace damaged cords immediately. Damaged cords
increase the risk of electric shock.
5. When operating a power tool outside, use an outdoor extension
cord marked “W-A” or “W”. These cords are rated for outdoor use and
reduce the risk of electric shock.
PERSONAL SAFETY
1. Stay alert, watch what you are doing, and use common sense when
operating a power tool. Do not use tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in moving parts.
3. Avoid accidental starting. Be sure switch is OFF before plugging in.
Carrying tools with your finger on the switch or plugging in tools that have
the switch ON invites accidents.
4. Remove adjusting keys or wrenches before turning the tool ON. A
wrench or a key that is left attached to a rotating part of the tool may result
in personal injury.
5. Do not overreach. Keep proper footing and balance at all times.
Proper footing and balance enables better control of the tool in unexpected
situations.
6. Use safety equipment. Always wear eye protection. Dust mask, non-
skid safety shoes, hard hat, or hearing protection must be used for
appropriate conditions.
TOOLS USE AND CARE
1. Use clamps or other practical way to secure and support the
workpiece to a stable platform. Holding the work by hand or against your
body is unstable and may lead to loss of control.
2. Do not force tool. Use the correct tool for your application. The
correct tool will do the job better and safer at the rate for which it is
designed.
3. Do not use tool if switch does not turn it ON or OFF. Any tool that
cannot be controlled with the switch is dangerous and must be repaired.
4. Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
5. Store idle tools out of reach of children and other untrained
persons. Tools are dangerous in the hands of untrained users.
6. Maintain tools with care. Keep cutting tools sharp and clean.
Properly maintained tools, with sharp cutting edges are less likely to bind
and are easier to control.
7. Check for misalignment or binding of moving parts, breakage of
parts, and any other condition that may affect the tool’s operation. If
damaged, have the tool serviced before using. Many accidents are
caused by poorly maintained tools.
8. Use only accessories that are recommended by the manufacturer
for your model. Accessories that may be suitable for one tool may become
hazardous when used on another tool.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
1. Tool service must be performed only by qualified repair personnel.
Service or maintenance performed by unqualified personnel could result in a
risk of injury.
2. When servicing a tool, use only identical replacement parts. Follow
instructions in the Maintenance Section of this manual. Use of
unauthorized parts or failure to follow Maintenance Instructions may create a
risk of electric shock or injury.
ADDITIONAL SPECIFIC SAFETY RULES
1.
Keep hands away from cutting area and blade. Keep
your second hand on auxiliary handle or motor housing. If both hands are
holding the saw, they cannot be cut by the blade.
2. Keep your body positioned to either side of the saw blade, but not in
line with the saw blade. KICKBACK could cause the saw to jump backwards.
(See "Causes and Operator Prevention of KICKBACK.")
3. Do not reach underneath the work. The guard cannot protect you from
the blade below the work.
4. Check lower guard for proper closing before each use. Do not operate
saw if lower guard does not move freely and close instantly. Never clamp
or tie the lower guard into the open position. If saw is accidentally dropped,
lower guard may be bent. Raise the lower guard with the Retracting Handle and
make sure it moves freely and does not touch the blade or any other part, in all
angles and depths of cut.
5. Check the operation and condition of the lower guard spring. If the
guard and the spring are not operating properly, they must be serviced
before use. Lower guard may operate sluggishly due to damaged parts, gummy
deposits, or a buildup of debris.
6. Lower guard should be retracted manually only for special cuts such
as “Pocket Cuts” and “Compound Cuts.” Raise lower guard by Retracting
Handle. As soon as blade enters the material, lower guard must be
released. For all other sawing, the lower guard should operate automatically.
7. Always observe that the lower guard is covering the blade before
placing saw down on bench or floor. An unprotected, coasting blade will
cause the saw to walk backwards, cutting whatever is in its path. Be aware of
the time it takes for the blade to stop after switch is released.
8. NEVER hold piece being cut in your hands or across your Ieg. It is
important to support the work properly to minimize body exposure, blade
binding, or loss of control.
9. Hold tool by insulated gripping surfaces when performing an operation
where the cutting tool may contact hidden wiring. Contact with a “live” wire
will also make exposed metal parts of the tool “live” and shock the operator.
10. When ripping always use a rip fence or straight edge guide. This
improves the accuracy of cut and reduces the chance for blade binding.
11. Always use blades with correct size and shape (diamond vs. round)
arbor holes. Blades that do not match the mounting hardware of the saw will
run eccentrically, causing loss of control.
12. Never use damaged or incorrect blade washers or bolts. The blade
washers and bolt were specially designed for your saw, for optimum
performance and safety of operation.
Kickback is the result of tool misuse and/or incorrect operating procedures or
conditions and can be avoided by taking proper precautions as given below:
13. Causes and Operator Prevention of Kickback:
Kickback is a sudden reaction to a pinched, bound, or misaligned saw blade,
causing an uncontrolled saw to lift up and out of the workpiece toward the
operator.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ
ꢀ
ꢀ
When the blade is pinched or bound tightly by the kerf closing down,
the blade stalls and the motor reaction drives the unit rapidly back
toward the operator.
If the blade becomes twisted or misaligned in the cut, the teeth at the
back edge of the blade can dig into the top surface of the wood causing
the blade to climb out of the kerf and jump back toward the operator.
Kickback is the result of tool misuse and/or incorrect operating procedures
or conditions and can be avoided by taking proper precautions as given
below:
14. Maintain a firm grip on the saw and position your body and arm in a
way that allows you to resist KICKBACK forces. KICKBACK forces can be
controlled by the operator, if proper precautions are taken.
15. When blade is binding, or when interrupting a cut for any reason,
release the trigger and hold the saw motionless in the material until the
blade comes to a complete stop. Never attempt to remove the saw from the
work or pull the saw backward while the blade is in motion or KICKBACK
may occur. Investigate and take corrective actions to eliminate the cause of
blade binding.
16. When restarting a saw in the workpiece, center the saw blade in the
kerf and check that teeth are not engaged into the material. If saw blade is
binding, it may walk up or KICKBACK from the workpiece as the saw is
restarted.
17. Support large panels to minimize the risk of blade pinching and
KICKBACK. Large panels tend to sag under their own weight. Supports must be
placed under the panel on both sides, near the line of cut and near the edge of
the panel.
18. Do not use dull or damaged blade. Unsharpened or improperly set blades
produce narrow kerf causing excessive friction, blade binding, and KICKBACK.
19. Blade depth and bevel adjusting locking levers must be tight and
secure before making cut. If blade adjustment shifts while cutting, it will cause
binding and KICKBACK.
20. Use extra caution when making a “Pocket Cut” into existing walls or
other blind areas. The protruding blade may cut objects that can cause
KICKBACK.
21. Some wood contains preservatives which can be toxic. Take extra care to
prevent inhalation and skin contact when working with these materials. Request,
and follow, all safety information available from your material supplier.
Improper operation or maintenance of this product could result
in serious injury and property damage. Read and understand all warnings and
operating instructions before using this tool. When using power tools, basic
safety precautions should always be followed to reduce the risk of personal
injury. For additional information visit our website www.porter-cable.com.
Additional Information regarding the safe and proper operation of power tools
(i.e. a safety video) is available from the Power Tool Institute, 1300 Sumner
Information is also available from the National Safety Council, 1121 Spring Lake
Drive, Itasca, IL 60143-3201, the American National Standards Institute ANSI
01.1Safety Requirements for Woodworking Machines, and the U.S. Department
of Labor regulations.
There are certain applications for which this tool was
designed. Porter-Cable strongly recommends that this tool NOT be modified
and/or used for any application other than for which it was designed. If you have
any questions relative to its application, DO NOT use the tool until you have
written Porter-Cable and we have advised you.
Technical Service Manager
Porter-Cable Corporation
4825 Highway 45 North
Jackson, TN 38305
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SYMBOL
DEFINITION
........................ volts
V
A
........................ amperes
........................ hertz
........................ watts
........................ kilowatts
........................ microfarads
........................ liters
Hz
W
kW
µF
l
kg
........................ kilograms
N/cm2 ........................ newtons per square centimeter
Pa
h
min
s
........................ pascals
........................ hours
........................ minutes
........................ seconds
........................ alternating current
3
........................ three-phase alternating current
3N
........................ three-phase alternating current with neutral
........................ direct current
........................ no load speed
n0
........................ alternating or direct current
....................... Class II Construction
........................ splash-proof construction
........................ watertight construction
…/min ........................ revolutions or reciprocation per minute
REPLACEMENT PARTS
When servicing use only identical replacement parts.
MOTOR
Many Porter-Cable tools will operate on either D.C., or single phase 25 to 60
cycle A.C. current and voltage within plus or minus 5 percent of that shown
on the specification plate on the tool. Several models, however, are designed
for A.C. current only. Refer to the specification plate on your tool for proper
voltage and current rating.
Do not operate your tool on a current on which the voltage is
not within correct limits. Do not operate tools rated A.C. only on D.C.
current. To do so may seriously damage the tool.
EXTENSION CORD SELECTION
If an extension cord is used, make sure the conductor size is large enough to
prevent excessive voltage drop which will cause loss of power and possible
motor damage. A table of recommended extension cord sizes will be found
in this section. This table is based on limiting line voltage drop to 5 volts (10
volts for 230 volts) at 150% of rated amperes.
If an extension cord is to be used outdoors it must be marked with the suffix
W-A or W following the cord type designation. For example – SJTW-A to
indicate it is acceptable for outdoor use.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
RECOMMENDED EXTENSION CORD SIZES FOR USE WITH PORTABLE ELECTRIC TOOLS
Length of Cord in Feet
115V
230V
25 Ft.
50 Ft.
50 Ft.
100 Ft. 150 Ft. 200 Ft.
250 Ft. 300 Ft.
500 Ft. 600 Ft.
400 Ft. 500 Ft.
800 Ft. 1000 Ft.
100 Ft. 200 Ft. 300 Ft. 400 Ft.
0-2
2-3
18
18
18
18
18
18
18
16
16
16
14
14
18
18
18
18
16
16
14
14
12
12
12
12
18
16
16
14
14
12
12
10
10
10
8
16
14
14
12
12
10
10
8
16
14
12
12
10
10
8
14
12
12
10
10
8
14
12
10
10
8
12
10
10
8
12
10
8
3-4
4-5
8
5-6
8
6
6-8
6
6
6
8-10
10-12
12-14
14-16
16-18
18-20
8
6
6
4
8
6
6
4
4
8
6
6
6
4
2
8
6
6
4
4
2
8
6
4
4
2
2
8
6
6
4
4
2
2
FUNCTIONAL DESCRIPTION
FOREWORD
Your Porter-Cable circular saw is designed for use with 7-1/4" diameter
blades that have a 5/8" diameter bore. Blades must be rated for 6000 RPM
operation (or higher).
A mounting flange kit for diamond-hole blades is available. This kit adapts
the saw for use with 7-1/4" diameter blades that have a diamond-shaped
mounting hole.
BLADE BRAKE (Model 424MAG only)
Model 424MAG is equipped with an electric blade brake that energizes
automatically when the trigger switch is released.
ASSEMBLY
REMOVING THE BLADE
DISCONNECT TOOL FROM POWER SOURCE.
Avoid contact with the blade teeth to prevent personal
injury.
This tool is equipped with a Quick Change
™
blade clamp
and is designed to be tightened hand-tight only. The use of
external tools may cause damage to the blade clamp.
DO NOT USE the Quick
blade clamp with any product
Change
™
A
other than specified Porter-Cable tools
423MAG and 424MAG.
1. Push in the arbor lock button (A) Fig. 1
and rotate the blade by hand until the
lock engages the blade arbor.
Fig. 1
Download from Www.Somanuals.com. All Manuals Search And Download.
7
A
A
Fig. 2
Fig. 3
2. While pressing the arbor lock button, extend the lever on the Quick
Change the blade clamp (A) Fig. 2 and turn it clockwise (left-hand
thread).
3. Remove the Quick Change blade clamp, release the arbor lock button,
and remove the outer blade flange.
NOTE: DO NOT use wet lubricants on the Quick Change blade clamp.
Verify that the Quick Change blade clamp lever is tight, and
quickly returns to its closed position before connecting the tool to the
power source. If it doesn’t return, clear the debris from the clamp. Visually
inspect the blade clamp lever regularly to ensure that it is not extended
during use.
INSTALLING THE BLADE
DISCONNECT TOOL FROM POWER SOURCE.
Avoid contact with the blade teeth to prevent personal
injury.
A
Fig. 4
Fig. 5
1. Remove any accumulated sawdust or other contaminants from the
guards, from around the arbor, and from the blade clamp.
2. Clean the inner blade flange, retract the telescoping guard, and place
the new blade on the arbor. Verify that the teeth point up at the front of
the saw (Fig. 4).
3. Place the outer blade flange (A) Fig. 5 on the arbor with the smooth side
against the blade. Mate the flats with those on the arbor.
4. Replace the Quick Change blade clamp (A) Fig. 2 finger tight by turning
it counter-clockwise. Push in the arbor lock button (A) Fig.1, extend the
lever on the Quick Change blade clamp (A) Fig. 2, and hand-tighten the
assembly securely. Release the arbor lock.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
TELESCOPING GUARD
The telescoping guard (A) Fig. 3 is a safety device important to your
protection. Every time you use the saw, verify that the telescoping guard
rotates freely and returns quickly and completely to its closed position. At
least once a month, remove any accumulated debris (sawdust, pitch, etc.)
from the area around the hub (B) of the telescoping guard. DO NOT
LUBRICATE THIS AREA. The hub has a dry film lubricated surface that
does not need oiling. DO NOT block or wedge the telescoping guard in the
open position.
DO NOT use your saw if the telescoping guard is not in
working order. If telescoping guard movement is sluggish or
binding exists, return the saw to your nearest AUTHORIZED
PORTER-CABLE SERVICE STATION or PORTER-CABLE
SERVICE CENTER for repair.
TO ADJUST DEPTH OF CUT FOR NORMAL CUTTING
Adjust the depth of cut so that the saw blade barely protrudes through the
thickness of the workpiece. To adjust:
DISCONNECT TOOL FROM POWER SOURCE.
1. Lift the depth adjustment locking lever (A) Fig. 6, located at the rear of
the saw.
2. Raise or lower the saw housing to the correct level.
NOTE: The upper guard (B) Fig. 6 is marked in 1/4" increments for
convenience in setting the depth of cut. Align the depth segment mark
(C) Fig. 6 with the desired depth marking on the guard.
3. Press the depth-adjusting locking lever down firmly to lock the saw in
the selected position.
A
C
B
A
B
C
D
Fig. 6
Fig.7
TO ADJUST FOR BEVEL CUTS
DISCONNECT TOOL FROM POWER SOURCE.
1. Loosen the bevel adjusting lever (A) Fig. 7.
2. Tilt the saw base until the desired graduation line on the bevel segment
(B) Fig. 7 aligns with the indicator (C) Fig. 7 on the bracket.
3. Tighten the bevel adjusting lever firmly.
4. For bevel cuts greater than 45°, set the guide on the 45° mark. Lift the
bevel adjusting lever into the slot (D) Fig. 7 and move the saw base to
the greater angle. Tighten the bevel adjusting lever firmly.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
0° POSITIVE STOP
The saw is equipped with an adjustable positive stop at 0°. Check the
accuracy of this stop periodically. To adjust:
DISCONNECT TOOL FROM POWER SOURCE.
1. Loosen the bevel adjustment lever (A) Fig. 8, and position the base for a
0° cut. Confirm that the bevel-stop sleeve (B) Fig. 8 is against the 0°
stop screw (C).
2. Turn the saw upside down, retract the telescoping guard, and check to
see that the blade is square (Fig. 9).
3. To adjust, loosen the bevel adjustment knob (A) Fig. 8. While keeping
the bevel stop sleeve (B) Fig. 8 in contact with the stop screw (C) Fig. 8,
use a screwdriver to turn the adjusting screw (A) Fig. 10 until the blade
is square.
A
A
B
C
Fig. 8
Fig.9
Fig. 10
LINE-OF-CUT INDICATOR
Line-of-cut indicator slots (A) Fig. 11 are provided
at the front of the saw base. The right slot is used
to follow a line when making a 0° cut. The left slot
is used to follow a line when making a 45° cut.
The straight side of the notch indicates the cut
line.
USING SAWDUST EXHAUST NOZZLE
A
The sawdust exhaust nozzle in the closed position
(Fig. 12) directs the sawdust to the rear of the saw.
Fig. 11
The sawdust exhaust nozzle pointing forward (Fig. 13) directs the sawdust
to the front. To change the position of the nozzle, push down on the top of
the nozzle and turn the nozzle to the new position. An accessory vacuum
hose assembly is available for connecting the sawdust exhaust nozzle in the
forward position directly to a shop type vacuum cleaner.
DO NOT direct sawdust toward yourself or others. To
avoid injury from flying sawdust, keep the exhaust nozzle either in the
forward position or in the closed position. DO NOT insert foreign objects
into the exhaust opening.
Fig. 12
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig.13
10
INSTALLING THE OPTIONAL RIP GUIDE
1. Insert the rip guide (A) Fig. 14 through the slots (B). Slide the guide in
until it extends through the both slots in the sawbase.
2. Place the compression spring on the thumb screw (C) Fig. 14 (supplied
with the rip guide), and thread into the hole in the saw base. DO NOT
TIGHTEN.
3. Adjust the rip guide for the desired width of cut and tighten the thumb
screw.
To avoid personal injury and damage to workpiece, extend
the rip guide through both slots in the base.
B C
A
Fig.14
Fig.15
Fig. 16
HOW TO USE THE SAW
DO NOT use your saw if the telescoping guard is not
working. If the telescoping guard binds or is sluggish, return
the saw to your nearest AUTHORIZED PORTER-CABLE
SERVICE STATION or PORTER-CABLE SERVICE
CENTER for repair.
For your maximum protection, effective control of this
powerful saw requires two-handed operation. Support the
work properly and hold the saw firmly to prevent loss of
control which could cause injury. See Fig. 15 for the proper
way to hold the tool.
Keep the cord away from cutting area to prevent electric
shock.
GUARD AGAINST KICKBACK.
Kickback is a sudden reaction to a pinched, bound, or
misaligned saw blade, causing an uncontrolled saw to lift up
and out of the workpiece toward the operator. Keep your
body to the side of the saw.
Stay alert and maintain a firm grip on the saw. Release the
switch immediately if the blade binds or the saw stalls. Keep
your blade sharp. Support the panels (Fig. 16). Use a fence
or a straight edge guide when ripping. DO NOT force the
tool. DO NOT remove the saw from the workpiece while the
blade is moving.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Fig. 18
Fig.17
CROSS-CUTTING
Cutting directly across the grain of a piece of lumber is called crosscutting.
Position the work so that the cut will be on the left.
RIPPING
Cutting wood lengthwise is referred to as ripping. This operation is
performed in the same manner as crosscutting with the exception of
supporting the workpiece. If the workpiece is supported on a large table,
bench, or floor, place several pieces of scrap stock approximately one inch
thick beneath the workpiece to allow clearance for the portion of the saw
blade that extends through the material (Fig. 17). When using saw horses,
place 2 x 4’s lengthwise between the horses and the large sheets of
paneling or thin plywood to prevent the workpiece from sagging in the
center.
For narrow rip cuts, use the rip guide (available as an accessory). Guide the
saw by keeping the inner face of the rip guide (Fig. 18) tight against the edge
of the board.
For making wider cuts (plywood and wide sheets), tack or clamp a wooden
guide strip to guide the left edge of the saw base (Fig. 17).
NOTE: Adjust the depth of cut to allow for the thickness of the wooden
guide strip.
A
Fig. 19
Fig. 20
BEVEL CUTTING
Bevel cuts are made in the same manner as crosscuts and rip cuts. The
difference is that the blade is set at an angle between 0° and 45°(Fig. 19).
The bevel cut made at an angle to the edge of a board is called a compound
cut. Certain compound cuts may require you to manually retract the
telescoping guard to allow the blade to enter into and/or through the cut.
Use the lever (A) Fig. 20 provided on the telescoping guard
when you have to retract the telescoping guard manually.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
POCKET CUTS (PLUNGE CUTTING)
A pocket cut is one which must be made inside
the area of the workpiece and not starting from
the edge. Mark the area clearly with lines on all
sides. Start near the corner of one side and
place the front edge of the saw base firmly on
the workpiece. Hold the saw up so that the
blade clears the material. Confirm that you have
adjusted the blade properly for the depth of cut.
Push the telescoping guard lever all the way
back so the blade is exposed (Fig. 21).
Fig. 21
Keep your hands and fingers away from the blade.
Start the motor and lower the blade into the work. After the blade has cut
through, and the base rests flat on the work, follow the line to the corner.
Let the saw come to a complete stop before removing it
from the workpiece.
Use a keyhole or bayonet saw to cut clean corners.
MAINTENANCE
KEEP TOOL CLEAN
Periodically blow out all air passages with dry compressed air. All plastic
parts should be cleaned with a soft damp cloth. NEVER use solvents to
clean plastic parts. They could possibly dissolve or otherwise damage the
material.
Wear ANSI Z87.1 safety glasses while using compressed air.
FAILURE TO START
Should your tool fail to start, check to make sure the prongs on the cord
plug are making good contact in the outlet. Also, check for blown fuses or
open circuit breakers in the line.
LUBRICATION
This tool has been lubricated with a sufficient amount of high grade lubricant
for the life of the unit under normal operating conditions. No further
lubrication is necessary.
BRUSH INSPECTION AND LUBRICATION
For your continued safety and electrical protection, brush inspection and
replacement on this tool should ONLY be performed by an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE·DELTA
FACTORY SERVICE CENTER.
At approximately 100 hours of use, take or send your tool to your nearest
authorized Porter-Cable Service Station to be thoroughly cleaned and
inspected. Have worn parts replaced and lubricate with fresh lubricant. Have
new brushes installed, and test the tool for performance.
Any loss of power before the above maintenance check may indicate the
need for immediate servicing of your tool. DO NOT CONTINUE TO
OPERATE TOOL UNDER THIS CONDITION. If proper operating voltage is
present, return your tool to the service station for immediate service.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE AND REPAIRS
All quality tools will eventually require servicing or replacement of parts due
to wear from normal use. These operations, including brush inspection and
replacement, should ONLY be performed by either an AUTHORIZED
PORTER-CABLE SERVICE STATION or a PORTER-CABLE•DELTA
FACTORY SERVICE CENTER. All repairs made by these agencies are fully
guaranteed against defective material and workmanship. We cannot
guarantee repairs made or attempted by anyone other than these agencies.
Should you have any questions about your tool, feel free to write us at any
time. In any communications, please give all information shown on the
nameplate of your tool (model number, type, serial number, etc.).
ACCESSORIES
A complete line of accessories is available from your Porter-Cable•
Delta Supplier, Porter-Cable•Delta Factory Service Centers, and Porter-
Cable Authorized Service Stations. Please visit our Web Site
www.porter-cable.com for a catalog or for the name of your nearest
supplier.
Since accessories other than those offered by Porter-
Cable ·Delta have not been tested with this product, use
of such accessories could be hazardous. For safest
operation, only Porter-Cable·Delta recommended
accessories should be used with this product.
PORTER-CABLE LIMITED
ONE YEAR WARRANTY
Porter-Cable warrants its Professional Power Tools for a period of one year from the date of original
purchase. We will repair or replace at our option, any part or parts of the product and accessories
covered under this warranty which, after examination, proves to be defective in workmanship or
material during the warranty period. For repair or replacement return the complete tool or accessory,
transportation prepaid, to your nearest Porter-Cable Service Center or Authorized Service Station.
Proof of purchase may be required. This warranty does not apply to repair or replacement required
due to misuse, abuse, normal wear and tear or repairs attempted or made by other than our Service
Centers or Authorized Service Stations.
ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE, WILL LAST ONLY FOR ONE (1) YEAR FROM THE DATE
OF PURCHASE.
To obtain information on warranty performance please write to: PORTER-CABLE CORPORATION,
4825 Highway 45 North, Jackson, Tennessee 38305; Attention: Product Service. THE FOREGOING
OBLIGATION IS PORTER-CABLE’S SOLE LIABILITY UNDER THIS OR ANY IMPLIED WARRANTY
AND UNDER NO CIRCUMSTANCES SHALL PORTER-CABLE BE LIABLE FOR ANY INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.
This warranty gives you specific legal rights and you may also have other legal rights which vary
from state to state.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
(CENTRE DE SERVICE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
(Locations où vous trouverez les pièces de rechange nécessaires ainsi qu’un service d’entretien)
•
Delta Power Tools are Available at These Locations
•
Delta)
Cleveland 44125
8001 Sweet Valley Drive
Unit #19
Phone: (216) 447-9030
Fax: (216) 447-3097
ARIZONA
MINNESOTA
Minneapolis 55429
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
GEORGIA
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Phone: (602) 437-1200
Fax: (602) 437-2200
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Phone: (404) 608-0006
Fax: (404) 608-1123
OREGON
MISSOURI
Portland 97230
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
ILLINOIS
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
PENNSYLVANIA
St. Louis 63119
Willow Grove 19090 (Philadelphia)
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
San Diego 92111
7638 Clairemnot Blvd.
Phone: (858) 277-9595
Fax: (858) 277-9696
NEW YORK
TEXAS
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
MARYLAND
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
COLORADO
Houston 77043
4321 Sam Houston Parkway, West
Suite 180
Phone: (713) 983-9910
Fax: (713) 983-6645
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
OHIO
FLORIDA
WASHINGTON
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
Phone: (954) 321-6635
Fax: (954) 321-6638
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
MICHIGAN
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
Fax: (248) 597-5004
Tampa 33609
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
Authorized Service Stations are located in many large cities. Telephone 800-487-8665 or 731-541-6042 for assistance locating one. Parts and
accessories for Porter-Cable Delta products should be obtained by contacting any Porter-Cable Delta Distributor, Authorized Service
Center, or Porter-Cable Delta Factory Service Center. If you do not have access to any of these, call 888-848-5175 and you will be directed to
the nearest Porter-Cable Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas grandes ciudades.
Llame al 800-487-8665 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios para los productos Porter-
Cable Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable Delta, Centro de Servicio Autorizado o Centro
de Servicio de Fábrica Porter-Cable Delta. Si no tiene acceso a ninguna de estas opciones, llame al 888-848-5175 y le dirigirán al Centro de
Servicio de Fábrica Porter-Cable Delta más cercano. Des centres de service agréés sont situés dans beaucoup de grandes villes. Appelez au
800-487-8665 ou au 731-541-6042 pour obtenir de l’aide pour en repérer un. Pour obtenir des pièces et accessoires pour les produits Porter-
•
•
•
•
•
•
•
•
Cable
•
Delta, s’adresser à tout distributeur Porter-Cable
•
Delta, centre de service agréé ou centre de service d’usine Porter-Cable
•
Delta. Si
vous n’avez accès à aucun de ces centres, appeler le 888-848-5175 et on vous dirigera vers le centre de service d’usine Porter-Cable
•
Delta le
plus proche.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
QUÉBEC
ALBERTA
MANITOBA
1515 Ave.
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, P.Q.
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
V5A 4T8
Phone: (604) 420-0102
Fax: (604) 420-3522
ONTARIO
1447, Begin
St-Laurent, (Mtl), P.Q.
H4R 1V8
Phone: (514) 336-8772
Fax: (514) 336-3505
505 Southgate Drive
Guelph, Ontario
N1H 6M7
Phone: (519) 767-4132
Fax: (519) 767-4131
The following are trademarks of PORTER-CABLE
•
DELTA (Las siguientes son marcas registradas de PORTER-CABLE
•
DELTA S.A.) (Les
marques suivantes sont des marques de fabriquant de la PORTER-CABLE
•
DELTA): Auto-Set®, BAMMER®, B.O.S.S.®, Builder’s Saw®,
Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series 2000™, DURATRONIC™, Emc²™, FLEX®, Flying
Chips™, FRAME SAW®, Grip Vac™, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®, JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-
SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-
CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, PORTER-CABLE REDEFINING PERFORMANCE™, Posi-Matic®, Q-
3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-LOC®,
Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®, STAIR EASE®,
The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL SELECT®, THIN-
LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®, UNIGUARD®, Unifence®,
UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER SERIES®,
WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other countries.
Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y también pueden
estar registradas en otros países. Marques déposées, indiquées par la lettre ™ et ®, sont déposées au Bureau des brevets d’invention et
Printed in U.S.A. PC-0104-150
Download from Www.Somanuals.com. All Manuals Search And Download.
marques déposées aux Etats-Unis et pourraient être déposées aux autres pays.
|