|
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1 General Introduction
Chapter 2 Hardware Description
Chapter 3 Configuration and Application
Chapter 4 Troubleshooting
Appendix A Specifications
Appendix B RJ-45 Pin Specification
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
General Introduction
1.1 Checklist
Check the contents of your package for following parts:
•
•
•
The Fast Ethernet Switch
User’s Manual
Power Cord
If any of these pieces are missing or damaged, please contact your dealer immediately, if
possible, retain the carton including the original packing material, and use them against
to repack the product in case there is a need to return it to us for repair.
1.2 Introduction
The 8/16-port 10/100Mbps Ethernet Switch is designed to allow simultaneous
transmission of multiple packets via an internal high-speed data channel. This means that
it can partition a network more efficiently than bridges or routers in most environments.
This Switch is a highly reliable network switch and is the ideal device for bridging Ethernet
to Fast Ethernet workgroups or networks. Simple and cost-effective, the Switch complies
to IEEE802.3u, IEEE802.3, 100Base-TX, and 10Base-T. Therefore, the Switch will be the
fast being recognized as one of the most important building blocks for today networking
technology. Choice of 100Base-FX optic-fiber ST/SC interface,
The FSD-801/1601ST&SC are also ideal to extend the network distance up to 2 kilometers
away as a link to your remote backbone.
The Switch also provide rack-mounting kits option for being installed On 10-inch or 19-
inch rack to ease the placement and management effort.
Compact in size and designed for Plug and Play installation, the Switch allows the network
administrator to simply connect the network and power cables and the switching/bridging
functions begin automatically. No hardware or software configurations are required.
The front panel of the Switch provides LED indicators for easy recognition of the switch
operation status and for troubleshooting. These LED indicators display the power status
for the system and link/activity, speed, and full-duplex status for each port.
With 8/16-port Fast Ethernet Switching designed specifically for connecting workgroup
devices and desktops, companies no longer have to invest in expensive and inflexible
switches engineered primarily for backbone implementations. Instead, companies can
deploy scaleable, affordable switches that increase the aggregate bandwidth of the
network by boosting throughput to the workgroups that need it most.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.3 Features
•
•
•
8/16-port 10/100base-TX Auto-Negotiation Ethernet Switches
One optional 100Base-FX fiber port for extending up to 2km
Complies with the IEEE802.3 Ethernet and IEEE802.3u Fast Ethernet stan-
dard
•
Features Store-and-Forward architectures with wire-speed filtering and for-
warding rates
•
•
Provide rack-mounting kit option for 10-inch and 19-inch Rack
Full/Half-Duplex capability on every TX ports, total bandwidth is up to
200Mbps/port
•
Support up to 1K/8K Uni-cast address, Layer 2 address resolution-Self Learn-
ing
•
•
•
IEEE802.3x compliant full-duplex flow control
Back pressure half-duplex flow control
Runt and CRC Filtering eliminates erroneous packets to optimize the network
bandwidth
•
•
•
•
Provide internal power supply
LED indicators for simple diagnostics and management
Auto- MDI and MDI-X detect for easily connecting to PC or hub/Switch uplink
DIP Switch for smart function (16-port model only)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Hardware Description
This section describes the hardware features of the Switch. For easier management and
control of the Switch, familiarize yourself with its display indicators, and ports. Front panel
illustrations in this chapter display the unit LED indicators. Before connecting any network
device to the hub, read this chapter carefully.
2.1 Front Panel
The unit front panel provides a simple interface monitoring the Switch. It includes a power
indicator for each port.
2.1.1 FSD-800/FSD-801
Figure 2-1 Front Panel of FSD-800 / FSD-801
LED indicators
Printing
Color
Description
Power
(PWR)
This indicator lights green when the Switch is receiving
power, otherwise it is off.
Green
This indicator green when the port is connected to a either
10Mbps Ethernet or 100Mbs Fast Ethernet station, If the
station to which the Switch connected is powered off, or if
there is a problem with the link, the LED will remain off.
And the indicator blinking green when the data will be re-
ceived to all other connected ports.
LNK/
ACT
Green
Green
This indicator green when the port is connected to a
100Mbps Fast Ethernet station. If the station to which the
Switch is connected is powered off, a 10Mbps Ethernet
station, or if there is a problem with the link, the LED will
remain off.
100
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Lit: Full duplex operation
Unlit: Half duplex operation
FDX/
COL
Blink: indicates data collisions on the respective Ethernet
segment of this port. Whenever a collision is detected, the
respective COL indicator will briefly blink.
This is normal when the network is busy.
Amber
Port # 8 of FSD-801 is a shared port. Either Twisted Pair port
or Fiber-optic port can operate in one time. Please power off
FSD-801 before switching the share port to different con-
nection type.
NOTE:
DIP Switch (FSD-801)
Printing
Description
The 100Base-FX fiber port of the switch is operating in full-
duplex mode.
FDX (default)
HDX
The port is operating in half-duplex mode.
check the opposite end is using the same transmit mode
before make the connection. If you want to adjust the DIP
switch, please power off FSD-801 first.
NOTE:
2.1.2 FSD-1600/FSD-1601
Figure 2-2 Front Panel of FSD-1600/ FSD-1601
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LED indicators
Printing
Color
Description
Power
(PWR)
This indicator lights green when the Switch is receiving
power; otherwise, it is off.
Green
Green
This indicator green when the port is connected to a either
10Mbps Ethernet or 100Mbs Fast Ethernet station , If the
station to which the Switch is connected is powered off, or if
there is a problem with the link, the LED will remain off.
And the indicator blinking green when the data will be re-
ceived to all other connected ports.
LNK/
ACT
This indicator green when the port is connected to a
100Mbps Fast Ethernet station. If the station to which the
100
Green Switch is connected is powered off, a 10Mbps Ethernet
station, or if there is a problem with the link, the LED will
remain off.
Lit: Full duplex operation
Unlit: Half duplex operation
FDX/
COL
Blink: indicates data collisions on the respective Ethernet
Amber
segment of this port. Whenever a collision is detected, the
respective COL indicator will briefly blink
This is normal when the network is busy.
Port # 16 of FSD-1601 is a shared port. Either Twisted Pair
NOTE:
port or Fiber-optic port can operate in one time.
2.2 Rear Panel
There is one power socket on the back of the switch, 100~240VAC, 50/60Hz. And one
more DIP-switch for FSD-1600 and FSD-1601 for smart function.
Figure 2-3 Rear Panel of the FSD-800/801
Figure 2-4 Rear Panel of the FSD-1600/1601
5
Download from Www.Somanuals.com. All Manuals Search And Download.
DIP Switch (Smart function for FSD-1600/1601)
DIP
Function
Description
ON: Enable FX
OFF: Enable TP
1
TP / FX Selection
Fiber Full/Half
duplex Switch
ON: Enable Fiber Full Duplex
OFF: Enable Fiber Half Duplex
2
3
ON: 15VLANs (port#1-15) with 1 overlapping
port (port#16) topology
VLAN topology
type selection
OFF: 14VLANs (port#1-14) with 2 overlapping
port (port#15,16) topology
ON: Enable VLAN
OFF: NO VLAN
4
5
6
7
8
Port Based VLAN
Port Trunk 0
ON: Enable Trunk group 0
OFF: Disable group 0
(port 1,2,3,4)
Port Trunk 1
ON: Enable Trunk group 1
OFF: Disable group 1
(port 5,6,7,8)
Port Trunk 2
ON: Enable Trunk group 2
OFF: Disable group 1
(port 9,10,11,12)
Port Trunk 3
ON: Enable Trunk group 3
(port 13,14,15,16) OFF: Disable group 3
TCP/IP TOS / DS
ON: Enable QoS
(Diffserv)
9
OFF: Turn off the QoS
Based QoS
802.1Q VLAN Tag
ON: Enable
10
Priority Based Qos OFF: Disable
12
11
Description
Off
Off
On
Off
On
Off
Disable
Port Based Prior-
ity QoS
Port 1-2 high priority ports (2 ports)
Port 1-4 high priority ports (4 ports)
11&12
On
On
Port 1-8 high priority ports (8 ports)
6
Download from Www.Somanuals.com. All Manuals Search And Download.
1. For fiber-optic connection, please check the opposite end is us-
ing the same transmit mode before make the connection.
2. Port#16 of the switch is shared with 100Base-FX port. Make
sure either Fiber-optic or twisted pair port is being connected.
NOTE:
3. For more information about the Smart function, please refer to
Chapter 3.
4. All the DIP is in OFF position by default!
2.3 Hardware Installation
1. Place the Switch on a smooth surface
2. Connect the output cord of power supply to the AC inlet.
3. Connect hub or PC to one port of the Switch using Category 3/4/5 UTP/STP
cabling.
4. Connect another hub or PC to the other port of Switch by following the same
process as described in Step 3.
Notice:
Cable distance for the Switch
The cable distance between the Switch and hub / PC should not exceed 100
meter.
The fiber-optic should not exceed 412 meters in Half-duplex mode and 2 kilome-
ters for Full-duplex mode
Make sure the wiring is correct
It can be used Category 3/4/5 cable in 10Mbps operation. To reliably operate your
network at 100Mbps, you must use an Unshielded Twisted-Pair (UTP) Category 5
cable, or better Data Grade cabling. While a Category 3 or 4 cable may initially
seem to work, it will soon cause data loss.
The fiber-optic cable should be a multi-mode fiber cable with 62.5/125μm or
50/125μm in specification.
You can find the information from the printing of the cable. If you are not familiar
with it, please consult your local dealers for the information.
Power System
The Switch accepts AC input with 100~240V AC, 50/60Hz. To prevent from data
loss or network downtime, consider install an UPS (Un-interrupt Power Supply) for
the Switch. And in some area, a surge suppression device also can help to prevent
from the Switch being damaged by un-regulated surge or current to it.
All kinds of hub / PC can connect to switch by using straight-through wires. The Switch
also supports auto MDI detection. This means you can direct connect any port of the
Switch to another MDI-X devices with a straight wire.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Configuration and Application
This chapter shows you how the Switch works, and how to install the Switch and also to
configure the smart functions provided in the 16-port model.
3.1 The Switch Operation
Address Table
The Switch is implemented with an address table. This address table composed of many
entries. Each entry is used to store the address information of some node in network,
including MAC address, port no, etc. The information comes from the learning process
of Ethernet Switch.
Learning
When one packet comes in from any port. The Ethernet Switch will record the source
address, port no. and the other related information in address table. These information
will be used to decide either forwarding or filtering for future packets.
Forwarding & Filtering
When one packet comes from some port of the Ethernet Switch, it will also check the
destination address besides the source address learning. The Ethernet Switch will lookup
the address table for the destination address. If not found, this packet will be forwarded
to all the other ports except the port which this packet comes in. And these ports will
transmit this packet to the network it connected. If found, and the destination address is
located at different port from this packet comes in, the Ethernet Switch will forward this
packet to the port where this destination address is located according to the information
from address table. But, if the destination address is located at the same port with
this packet comes in, when this packet will be filtered. Thereby increasing the network
throughput and availability
Store-and-Forward
Store-and-Forward is one type of packet-forwarding techniques. A Store-and-Forward
Ethernet Switch stores the incoming frame in an internal buffer, do the complete error
checking before transmission. Therefore, no error packets occurrence, it is the best
choice when a network needs efficiency and stability.
The Switch scans the destination address from the packet header, searches the routing
table provided for the incoming port and forwards the packet, only if required. The fast
forwarding makes the switch attractive for connecting servers directly to the network,
thereby increasing throughput and availability. However, the switch is most commonly
used to segment existing hubs, which nearly always improves overall performance.
A Ethernet Switch can be easily configured in any Ethernet network environment to
significantly boost bandwidth using conventional cabling and adapters.
Due to the learning function of the Ethernet switch, the source address and corresponding
port number of each incoming and outgoing packet are stored in a routing table. This
information is subsequently used to filter packets whose destination address is on the
same segment as the source address. This confines network traffic to its respective
8
Download from Www.Somanuals.com. All Manuals Search And Download.
domain, reducing the overall load on the network.
The Switch performs “Store-and-forward” therefore, no error packets occur. More
reliably, it reduces the re-transmission rate. No packet loss will occur.
Auto-Negotiation
The STP ports on the Switch have built-in "Auto-Negotiation." This technology
automatically sets the best possible bandwidth when a connection is established with
another network device (usually at Power On or Reset). This is done by detect the modes
and speeds at the second of both device is connected and capable of. Both 10Base-T and
100Base-TX devices can connect with the 100Base-TX port in either Half- or Full-Duplex
mode.
If attached device is:
100Base-TX port will set to:
10Mbps
*10Mbps, no auto-negotiation
*10Mbps, with auto-negotiation
*100Mbps, no auto-negotiation
*100Mbps, with auto-negotiation
10/20Mbps (10Base-T/Full-Duplex)
100Mbps
100/200Mbps (100Base-TX/Full-Duplex)
3.2 The Smart Function (16-port model)
The FSD-1600 and FSD-1601 is with one DIP switch on the rear of the switch, these ON/
OFF switches provides the functions as below:
•
•
•
•
•
Twisted Pair or Fiber-optic selection
Port based VLAN
Port Trunking
ToS/ QoS selection
Priority Setup
They are all in OFF position by default!
3.2.1 TP or Fiber-optic selection (for FSD-1601 only)
Related DIP: 1, 2
Default meaning: Port#16 runs in Twisted pair, Auto-Negotiation.
DIP 1: Turns on will force the fiber-optic port enabled.
Please do not turn on if you are using FSD-1600.
NOTE:
DIP 2: Turns on will force the 100Base-FX fiber-optic port runs in Full-duplex mode.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2.2 Port-based VLAN
Related DIP: 3, 4
Default meaning: No VLAN setting.
VLAN can be used to separate ports into different groups in the same switch. This will
secure port from being accessed by other ports on the switch.
DIP 4: Turns on will enable the port-based VLAN capability
DIP 3: The two positions represent two different VLAN choices:
OFF:There are 14 VLANs. Port 1 to Port 14 can communicate with Port 15,
and Port 16 where 1 to 14 cannot see each other.
ON: There are 15 VLANs. Port 1 to Port 15 cannot see each other but they
all can retrieve data from port 16. i.e. members of VLAN 1 are 1 & 16,
VLAN 2 are 2 & 16, VLAN 3 are 3 & 16, etc.
3.2.3 Port-Trunking
Related DIP: 5, 6, 7, 8
Default meaning: No port-trunking.
Port trunks will four times the bandwidth (800Mbps) while connecting with another
switches that also with port trunk capability. Up to four groups where each group with 4
ports is allowed.
DIP 5: Turns on to enable trunk 0, from port 1 to port 4.
DIP 6: Turns on to enable trunk 1, from port 5 to port 8.
DIP 7: Turns on to enable trunk 2, from port 9 to port 12.
DIP 8: Turns on to enable trunk 3, from port 13 to port 16.
Turn on the Trunk will also disable VLAN capability.
NOTE:
3.2.4 IP ToS/DS (DiffServ), VLAN Tag Based QoS
Related DIP: 9, 10
Default meaning: No priority-packet detection.
The Switch will store each incoming packets and check the tag field to determine the
priority, high or low. Then follow the priority to forward to the destination.
The Switch supports two types of detection.
•
•
VLAN Tag-based detection (Layer 2)
ToS/DS (DiffServ) detection (IP Layer 3)
DIP 9: Turns on for IP ToS/DS QoS.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
DIP 10: Turns on for VLAN tag priority QoS.
The connected end-nodes (PCs, Routers) should also support
VLAN priority or ToS priority. Normally, these functions could
turn off by default. Check the user’s guide of your networked
device for this capability.
NOTE:
3.2.5 Port-based priority
Related DIP: 11, 12
Default meaning: No hardware port priority.
If your end-nodes do not support priority, and you would like to preserve more bandwidth
for those network users, port-based priority will direct set the related port to high
priority.
DIP 11
ON
DIP 12
OFF
ON
Description
Port 1 and Port 2 are high priority ports
Port 1~ 4 are high priority ports
Port 1 ~8 are high priority ports
OFF
ON
ON
FSD-1600/1601 only support dual priority, this means the
priority only will be HIGH or LOW no matter which port you
connected to.
NOTE:
Priority support can co-work with VLAN.
NOTE:
3.3 Application
3.3.1 Basic 100Mbps Server, PCs to 10/100Mbps Switch
Plug one end of the Category 5 UTP Cable into any one port of the Switch, and the other
end of this cable into the RJ-45 of Fast Ethernet Adapter in the server or PC. The cable
length between these 2 connecting points should not exceed 100 meters.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 3-1 10/100Mbps File server to Switch Connection
3.3.2 Connect to 100Base-FX Switch/Device (Model: FSD-801/1601)
Plug the pair the fiber-cable to the Switch’s fiber-optic port, secure the fiber-optic
connector. Connect to other end to the fiber-optic port of the device like repeater hub,
switch or workstations.
Be noted for the duplex mode. For Hub, only Half-Duplex mode can be selected, at the
mean time, the cable distance cannot exceed 412 meters. For Switch or end-node that
works on full-duplex mode, the maximum distance cannot exceed 2 kilometers.
The pair of the connectors must be crossed, ie. TX/RX port of the Switch should connect
to RX/TX Port of the device in other end.
Consult your local dealer for more information about fiber-optic wires, connector type or
network distances.
Figure 3-2 Fiber-cable Switch to Switch Connection
12
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.3 Set up the workgroup and uplink to the backbone (Model: FSD-
1600/1601)
Figure 3-3 Connection with VLAN enable
Turn on the DIP 4, the FSD-1600 soon separate the fourteen ports (Port 1 to Port 14) into
different group, then you can install two file servers to port 15, port 16, those fourteen
users shall not see each other where they can freely access the information from the
two file server. Or, port 15 is connect to your local server and port 16 up connect to your
networks backbone, either 100 meters (FSD-1600) or 2 kilometers away (FSD-1601, both
DIP 1 & 2 in ON position)
3.3.4 Set up Video/Voice Networks (Model: FSD-1600/1601)
Some networks could have a devices like Video or Voice device like Internet Telephony
Gateway, the support of priority may help you to make your voice or video in higher
position to get the precious networks bandwidth, for example to the Intermet.
If your Voice Gateway support ToS, you may direct turn on the DIP 9 to get the higher
priority, or if your device or network nodes do not support you can turn on DIP 11 or DIP
12 to have the hardware priority,
Figure 3-4 3 Voice Gateway to Switch Connection
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Troubleshooting
This chapter contains information to help you solve problems. If the Switch is not
functioning properly, make sure the Switch was set up according to instructions in this
manual.
The Link LED is not Lit
Solution:
Make sure the switch configuration is consistent with the connecting device
Check the cable connections.
Performance is bad
Solution:
Check the full duplex status of the Ethernet Switch. If the Ethernet Switch is set to full
duplex and the partner is set to half duplex, then the performance will be poor.
Some stations can not talk to other stations located on the other port
Solution:
The address table may contain older information than of the address table of that node.
Please power down to refresh the address information.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Specifications
General (Ethernet)
IEEE 802.3 10Base-T EthernetIEEE 802.3u 100 Base-TX and
100Base-FX Fast EthernetIEEE 802.3x Flow control
Standards:
Protocol:
CSMA/CD
Ethernet:
Data Transfer
Rate:
10Mbps(half duplex) / 20Mbps (full duplex) Fast Ethernet:
100Mbps (half duplex) / 200Mbps (full duplex)
Topology:
Star
General (Cabling)
• 10Base-T:2-pair UTP Cat. 3,4, 5 (100 m, max.)EIA/TIA-
568 100-ohm STP (100 m, max.)
• 100Base-TX:2-pair UTP Cat. 5 (100 m, max.)EIA/TIA-568
100-ohm STP (100 m, max.)
Network Cables:
• 100Base-FX: (Models: FSD-4/8/1601)
1-pair Multi-mode optic fiber 62.5/125μm, 50/125μm(2
km, max.)
8/16-STP ports
Number of
Ports:
Models:FSD-8/1601
1-ST/SC fiber-optic port (1300nm wavelength)
Hardware Physical /Environmental Specification
100~240VAC, 50/60Hz
AC inputs
Power Con-
sumption
15~25 watts
System : PowerPort: 3 LED Indicators per port
(LINK/ACT, 100, FDX/ COL)
LED Indication
Operating Tem-
perature
0 ~ 50 degree C
Storage Tem-
perature
-20 ~ 70 degree C
Humidity
10% ~ 90% non-condensing
Dimensions
220 x 135 x 44 mm (W x D x H)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
EMI
FCC Class A, CE Mark Class A
Performance
Transmission
Method
Store-and-forward
Filtering Address
Table
1/8K entries
Packet Filtering/
14,880pps per port (for 10Mbps)
Forwarding Rate 148,800pps per port (for 100Mbps)
MAC Address
Automatic update / Max age: fixed
Learning
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
RJ-45 Pin Specification
When connecting your FSD-series 10/100Mbps Ethernet Switch to another switch, a
bridge or a hub, a modified crossover cable is not necessary. Each port of the Switch
is auto-MDI detection. That means you can direct connect the Switch to any Ethernet
devices with a Category 5, UTP straight wire.
However, the following diagram and tables also show the standard RJ-45 receptacle/
connector and their pin assignments for the switch-to-network adapter card connection,
and the straight / crossover cable for the Switch-to-switch/hub/bridge connection.
RJ-45 Connector pin assignment
Contact
Media Direct Interface Signal
TX + (transmit)
TX - (transmit)
Rx + (receive)
Not used
Media Direct Interface -Cross
Rx + (receive)
1
2
Rx - (receive)
3
TX + (transmit)
4, 5
6
Rx - (receive)
Not used
TX - (transmit)
7, 8
The standard cable, RJ-45 pin assignment
The standard RJ-45 receptacle/connector
17
Download from Www.Somanuals.com. All Manuals Search And Download.
This page is intentionally left blank
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Part No.: 2010-000004-003
Download from Www.Somanuals.com. All Manuals Search And Download.
|