Pre-N Wireless Router
WNRT-610
User’s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Federal Communication Commission (FCC) Radiation Exposure
Statement
This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In
order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity
to the antenna shall not be less than 20 cm(8 inches) during normal operation.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
Protection requirements for health and safety – Article 3.1a
Testing for electric safety according to EN 60950 has been conducted. These are considered relevant
and sufficient.
Protection requirements for electromagnetic compatibility – Article 3.1b
Testing for electromagnetic compatibility according to EN 301 489-1, EN 301 489-17 and EN 55024
has been conducted. These are considered relevant and sufficient.
Effective use of the radio spectrum – Article 3.2
Testing for radio test suites according to EN 300 328-2 has been conducted. These are considered
relevant and sufficient.
CE in which Countries where the product may be used freely:
Germany, UK, Italy, Spain, Belgium, Netherlands, Portugal, Greece, Ireland, Denmark, Luxembourg,
Austria, Finland, Sweden, Norway and Iceland.
France: except the channel 10 through 13, law prohibits the use of other channels
Safety
This equipment is designed with the utmost care for the safety of those who install and use it. However,
special attention must be paid to the dangers of electric shock and static electricity when working with
electrical equipment. All guidelines of this and of the computer manufacture must therefore be allowed
at all times to ensure the safe use of the equipment.
WEEE regulation
To avoid the potential effects on the environment and human health as a result of the
presence of hazardous substances in electrical and electronic equipment, end users of
electrical and electronic equipment should understand the meaning of the crossed-out
wheeled bin symbol. Do not dispose of WEEE as unsorted municipal waste and have to
collect such WEEE separately.
Download from Www.Somanuals.com. All Manuals Search And Download.
Revision
User’s Manual for PLANET Wireless Pre-N Broadband Router
Model: WNRT-610
Rev: 1.0 (January. 2007)
Part No. EM-WRT610
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
1.1 PACKAGE CONTENTS ......................................................................................................................2
1.2 SYSTEM REQUIREMENTS ................................................................................................................2
1.3 FEATURES .......................................................................................................................................2
1.4 SPECIFICATION................................................................................................................................3
1.5 WIRELESS PERFORMANCE ..............................................................................................................3
CHAPTER 2 HARDWARE INSTALLATION....................................................................................5
2.1 HARDWARE CONNECTION...............................................................................................................5
2.2 LED INDICATORS............................................................................................................................6
CHAPTER 3 CONFIGURE THROUGH WEB BROWSER.............................................................7
3.1 SETUP WIZARD ...............................................................................................................................8
3.3 WIRELESS .....................................................................................................................................13
3.4 PASSWORD....................................................................................................................................15
3.5 STATUS .........................................................................................................................................16
3.6 ADVANCED FEATURES...................................................................................................................16
3.6.2 URL Filter............................................................................................................................17
3.6.5 Firewall Rules......................................................................................................................20
3.6.9 Schedule...............................................................................................................................23
3.7 ADMINISTRATOIN..........................................................................................................................23
3.7.1 PC Database........................................................................................................................24
3.7.2 Network Diagnostics............................................................................................................25
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 LOG OUT ......................................................................................................................................29
3.9 RESTART .......................................................................................................................................29
WINDOWS 2000..................................................................................................................................30
WINDOWS XP.....................................................................................................................................30
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
The Planet WNRT-610 is a wireless Pre-N router that supports high-speed wireless networking for home
or SOHO users. The WNRT-610 provides data rate up to 300 Mbps when used with other wireless Pre-N
Planet products, like USB adapter WNL-U550 and PCI WNL-9310. The Pre-N standard is backwards
compatible with 802.11b and 802.11g products. There is no need to change existing network to maintain
connectivity. You may sacrifice some of 802.11g’s performance when using 802.11b and 802.11g
devices in the same WLAN, but you still can keep the ability to communicate when deploying the 802.11g
standard into your 802.11b network.
The WNRT-610 supports the most advanced security features available today: WPA-PSK/WPA2-PSK.
Authorizes and identifies users based on a secret key that changes automatically at a regular interval.
WPA-PSK/WPA2-PSK uses TKIP or AES to change the temporal key periodically. This insures much
greater security than the standard WEP security. (By contrast, the older WEP encryption required the
keys to be changed manually.)
The WNRT-610 will obtain a new security key every time it connects to the 802.11g network. You only
need to enter your encryption information once in the configuration menu. Then you will automatically
receive a new key every time you connect, thus highly increasing the safety of your communications.
The WNRT-610 allows you setup trigger ports of special applications, and let you utilize Internet services
smoothly. The firewall features can protect your Intranet PCs from illegal access and many kinds of DoS
attacks from the Internet. The Virtual Server and DMZ functions let you setup your servers in the Intranet
and still can provide services to the Internet users. Access Control function allows you to block the
Internet service to different clients.
The WNRT-610 supports the most advanced security features available today: WPA-PSK/WPA2-PSK.
WPA (Wi-Fi Protected Access) authorizes and identifies users based on a secret key that changes
automatically at a regular interval. WPA/WPA2-PSK uses TKIP or AES to change the temporal key
periodically. This insures much greater security than the standard WEP security. (By contrast, the older
WEP encryption required the keys to be changed manually.)
Utilizing the PSK (Pre Shared Key) mode of WPA, the WNRT-610 will obtain a new security key every
time it connects to the 802.11g network. You only need to enter your encryption information once in the
configuration menu. Then you will automatically receive a new key every time you connect, thus highly
increasing the safety of your communications.
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 Package Contents
Make sure that you have the following items:
• One WNRT-610
• One AC Power Adapter
• One User’s Manual CD
• One Quick Installation Guide
Note: If any of the above items are missing, contact your supplier as soon as
possible.
1.2 System Requirements
Before installation, please check the following requirements with your equipment.
• Ethernet-based ADSL / Cable modem
• Computers with Microsoft Windows, Macintosh, or Linux operating systems
equipped with an Ethernet adapter and a CD-ROM drive
• Internet Explorer v6.0 or Netscape Navigator v6.0 and above
1.3 Features
• Compliant with IEEE802.11n (draft 1.0) standard
• 2.4GHz ISM band, unlicensed operation
• Supports WPA/WPA2-PSK (TKIP or AES)
• Backward compatible 802.11g and 802.11b
• Supports DHCP server
• Web Configuration provide a user friendly interface for the user to configure
through web browser
• Supports UPnP (Universal Plug and Play)
• Supports MAC / IP / Protocol Filter
• Supports DDNS, virtual server and DMZ
• Build-in 4 -port switch
• Provides Setup Wizard for the user to configure easily in the first time
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
1.4 Specification
Standards
IEEE 802.3u 100BASE-TX Fast Ethernet
IEEE802.11n, IEEE 802.11g, IEEE 802.11b
CSMA/CD
Protocol
Radio Technology
Data Transfer Rate
OFDM
802.11b: 1, 2, 5.5, 11Mbps
802.11g: 6, 9, 12, 18, 24, 36, 48, 54Mbps
Pre-802.11n: Up to 300Mbps
20dBm (Max)
TX Power
Power Consumption
5W (Max)
Frequency Range
2412 ~ 2484 MHz ISM band (channels 1 ~ 14)
DBPSK/DQPSK/CCK/OFDM
Modulation Schemes
64/128-bits WEP Encryption; WPA, WPA-PSK
Security
Channels
1 ~ 11 channels (FCC); 1 ~ 13 channels (ETSI);
1 ~ 14 channels (MKK)
Number of Ports
LAN: 4 x 10/100Mbps Auto-MDIX Fast Ethernet port
WAN: 1 x 10/100Mbps Auto-MDIX Fast Ethernet port
DC inputs
Temperature
Humidity
Dimensions
EMI:
DC 12V 1A
Operating: 0° ~ 40° C, Storage: -10° ~ 70° C
Operating: 10% ~ 90%, Storage: 5% ~ 90%
153 x 173 x 64 mm (W x H x D) without Antenna
FCC Class B, CE Mark B
1.5 Wireless Performance
The following information will help you utilizing the wireless performance, and operating coverage of
WNRT-610.
1. Site selection
To avoid interferences, please locate WNRT-610 and wireless clients away from transformers,
microwave ovens, heavy-duty motors, refrigerators, fluorescent lights, and other industrial
equipments. Keep the number of walls, or ceilings between AP and clients as few as possible;
otherwise the signal strength may be seriously reduced. Place WNRT-610 in open space or add
additional Access Point as needed to improve the coverage.
2. Environmental factors
The wireless network is easily affected by many environmental factors. Every environment is
unique with different obstacles, construction materials, weather, etc. It is hard to determine the
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
exact operating range of WNRT-610 in a specific location without testing.
3. Antenna adjustment
The bundled antenna of WNRT-610 is adjustable. Firstly install the antenna pointing straight up,
then smoothly adjust it if the radio signal strength is poor. But the signal reception is definitely weak
in some certain areas, such as location right down the antenna.
Moreover, the original antenna of WNRT-610 can be replaced with other external antennas to
extend the coverage. Please check the specification of the antenna you want to use, and make
sure it can be used on WNRT-610.
4. WLAN type
If WNRT-610 is installed in an 802.11b/g/n mixed WLAN, its performance will reduced significantly.
Because every OFDM packet needs to be preceded by an RTS-CTS or CTS packet exchange that
can be recognized by legacy 802.11b devices. This additional overhead lowers the speed. If there
are no 802.11b devices connected, or if connections to all 802.11b devices are denied so that
WNRT-610 can operate in 11g-only mode, then its data rate should actually 300Mbps.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Hardware Installation
Before you proceed with the installation, it is necessary that you have enough information about the
WNRT-610.
2.1 Hardware Connection
1. Locate an optimum location for the WNRT-610. The best place for your WNRT-610 is usually at
the center of your wireless network, with line of sight to all of your mobile stations.
2. Connect the power adapter to the receptor at the rear panel of the WNRT-610, and plug the other
end of the power adapter to a wall outlet or power strip. The Power LED will light up to indicate
proper operation.
3. Power off the ADSL / Cable modem first. Connect ADSL/Cable Modem to the WAN port on
WNRT-610. Use the cable supplied with your modem. If no cable was supplied with your modem,
please use a RJ-45 Ethernet cable. After the Ethernet cable is securely connected, power on the
ADSL / Cable modem. The WAN LED will light up to indicate proper connection.
4. Use an Ethernet cable to connect one of the LAN ports on the WNRT-610 and the computer you
are using to configure the router. The corresponding LAN LED will light up to indicate proper
connection. The LAN ports on the WNRT-610 are Auto-MDI/MDIX; thus, you can use a straight or
crossover Ethernet cable freely.
5. Adjust the antennas of WNRT-610. Try to adjust them to a position that can best cover your
wireless network. The antenna’s position will enhance the receiving sensitivity.
Note: ONLY use the power adapter supplied with the WNRT-610. Otherwise, the product may be
damaged.
Note: If you want to reset WNRT-610 to default settings, press and hold the Reset button over 5
seconds. And then wait for 10 seconds for WNRT-610 restart.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
2.2 LED Indicators
Security
Wireless
On - Wireless security is On.
Off - Wireless security is Off.
On - Wireless enabled.
Off - No Wireless connections currently exist.
Flashing - Data is being transmitted or received via the Wireless
access point. This includes "network traffic" as well as user data.
On - Corresponding LAN (hub) port is active.
Off - No active connection on the corresponding LAN (hub) port.
Flashing - Data is being transmitted or received via the corresponding
LAN (hub) port.
LAN
Power LED
(Blue)
On - Power on.
Off - No power.
Flashing - This LED blinks during start up, and during a Firmware
Upgrade.
WAN
On - Connection to the modem attached to the WAN (Internet) port is
established.
Flashing - Data is being transmitted or received via the WAN port.
On - Internet connection is available.
Internet
Off - No Internet connection available.
Flashing - Data is being transmitted or received via the ADSL
connection.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Configure through Web Browser
Web configuration provides a user-friendly graphical user interface (web pages) to manage your
WNRT-610.
WNRT-610 contains an HTTP server. This enables you to connect to it, and configure it, using your Web
Browser. Your Browser must support JavaScript.
The configuration program has been tested on the following browsers:
Netscape 7.1 or later. Mozilla 1.6 or later or Internet Explorer V5.5 or later
1. Open your web browser.
2. Enter the IP address of your WNRT-610 in the address field (default IP address is http://192.168.0.1).
3. A User Name and Password dialog box will appear. Please enter your User Name and Password here.
Default User Name is “admin” and Password is “password”. Click “OK”.
4. When the first time you enter WNRT-610, Setup Wizard will pop up. Please refer to our Quick
Installation Guide to use the Setup Wizard for initial configuration. Setup Wizard will guide you through
configuration step by step.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1 Setup Wizard
3.1.1 Dynamic IP address
Please refer to your Internet connection method to select the Connection Type. And please configure
those settings per the information your ISP provides.
If you choose the Dynamic IP address type, click the “ Next “,you wil see the following web screen.
Connection Type: Select the connection type, Dynamic, Fixed IP, PPPoE, or PPTP from the drop-down
list.
When using Dynamic client/Fixed IP, enter the following information in the fields (some information are
provided by your ISP):
WAN IP: Select whether you want to specify an IP address manually, or want DHCP to obtain an IP
address automatically. When “Specify IP” is selected, type the IP address, subnet mask, and default
gateway in the fields. Your ISP will provide you with this information.
Copy from PC: If required by your ISP, type the MAC address for the WNRT-610 WAN interface in this
field. You can also copy the MAC address of your PC’s network card to the WNRT-610 WAN interface
by clicking “Copy from PC”.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.3 PPPoE
When using PPPoE, enter the following information in the fields (some information are provided by your
ISP):
Login Name: Type your PPPoE user name.
Password: Type your PPPoE password.
IP Address: Select whether you want the ISP to provide the IP address automatically, or whether you
want to assign a static IP address to the WNRT-610 WAN interface. When “Specify IP” is selected, type
the PPPoE IP address in the field. Your ISP will provide you with this information.
DNS : Type up to three DNS numbers in the fields. Your ISP will provide you with this DNS information.
Connect on Demand: Enables or disables the connect on demand function, which enables WNRT-610
to initiate a connection with your ISP when an Internet request is made to the WNRT-610. When enabled,
the WNRT-610 automatically connects to the Internet when you open your browser.
- 10 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.1.4 PPTP
When using PPTP, enter the following information in the fields (some information are provided by your
ISP):
PPTP Server : Type the IP address or name of server which offers Internet service. Your ISP will provide
you with this information.
Login Name: Type your PPTP account.
PPTP Password: Type your PPTP password.
Auto-reconnect: If this function is enabled, WNRT-610 will try to rebuild Internet connection once the
link is down.
- 11 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 LAN
You can configure WNRT-610 DHCP server function in this screen. When configuration is completed,
please click “Save” to save and restart WNRT-610.
IP address: Set for the Wireless Broadband Router, as seen from the local LAN. Use the default value
unless the address is already in use or your LAN is using a different IP address range. In the latter case,
enter an unused IP Address from within the range used by your LAN.
Subnet Mask: The default value 255.255.255.0 is standard for small (class "C") networks. For other
networks, use the Subnet Mask for the LAN segment to which the Wireless Broadband Router is
attached (the same value as the PCs on that LAN segment).
DHCP Server: Click to enable the function.
- 12 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3 Wireless
This screen enables you to configure advanced wireless functions.
Region: Select the correct domain for your location.
Wireless Radio: Enable or disable wireless LAN via the WNRT-610.
SSID: Type an SSID in the field. The SSID of any wireless device must match the SSID typed here in
order for the wireless device to access the LAN and WAN via the WNRT-610.
Mode: Select the Mode off / 802.11b / 802.11b + g /802.11b + g + n/ 802.11 g + n /802.11 n
Channel: Select a work channel for wireless communications. The channel of any wireless device must
match the channel selected here in order for the wireless device to access the LAN and WAN via the
WNRT-610.
SSID Broadcast: If disabled, no SSID is broadcast. If enabled, the SSID of WNRT-610 will then be
broadcast to all wireless stations. Stations which have no SSID (or a "null" value) can then adopt the
correct SSID for connections to this router.
MAC Filter : Select disable / Allow / Deny to use Wireless MAC Filter function
802.11e QoS : It defines a set of Quality of Service enhancements for LAN applications, in particular the
802.11 WiFi standard.
- 13 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.3.1 Wireless Security
Authentication Type: Select the type from the listed options. If WEP is selected, the screen would
appear as above.
WEP Type: You can choose to use Open system or Shared key.
Mode: Select the key code you want to use for WEP Key, HEX or ASCII. When Hex is selected, you may
enter alphanumeric characters in the range of “A-F”, “a-f” and “0-9” in the WEP Key entry field.
Alternatively, you may enter digit hexadecimal values in the range of “a-z”, “A-Z” and “0-9”.
WEP Key: Select the level of encryption you want from the drop-down list. WRT-415 supports 64, and
128-bit encryption.
Key 1 ~ Key 4: There are 4 keys available, please ensure you have enter correct number for the key
values with different Key Length and coding (Hex or ASCII) as 64bit (10 Hex digit / 5 ASCII), 128bit (26
Hex digit / 13 ASCII) or 256bit (58 Hex digit / 29 ASCII), please select one of them and enter the key you
want to use. Click “Clear” to erase key values.
Note: 128bit WEP encryption will require more system resources than 64bit encryption. Use 64-bit
encryption for better performance.
Authentication Type: Select the type from the listed options. If WPA/WPA2-PSK is selected, the screen
would appear as above.
WPA/WPA2-PSK is selected in the Authentication Type field, the screen appears as below.
- 14 -
Download from Www.Somanuals.com. All Manuals Search And Download.
If WPA/WPA2-PSK is selected, the screen appears as below. Please enter a hard-to-guess passphrase
(between 8 and 63 characters) in the field.
3.4 Password
The password screen allows you to assign a password to the Wireless Broadband
Router.
Old Password: Enter the existing password in this field.
New password: Enter the new password here.
Verify password: Re-enter the new password here.
- 15 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.5 Status
This screen enables you to view the router LAN, wireless LAN, and WAN configuration.
Connection Details : Click this button to open a sub-window and view a detailed description of the
current connection. Depending on the type of connection, a "log" may also be available.
3.6 Advanced Features
3.6.1 Internet
Type a host IP address for the DMZ. The computer with this IP address acts as a DMZ host with
unlimited Internet access.
- 16 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.2 URL Filter
If you want to limit access to certain sites on the Internet, you can use this feature.
The URL filter will check each Web site access. If the address, or part of the address,
is included in the block site list, access will be denied.
Current Filter Strings: The list contains the current list of items to block.
Add Filter String : To add to the current list, type the word or domain name you want to block into the
field provided, then click the Add button.
Filter strings should be as specific as possible. Otherwise, you may block access to many more sites
than intended.
Allow Trusted PC: Enable this to allow one computer to have unrestricted access to the Internet. For
this PC, the URL filter will be ignored.
If enabled, you must select the PC to be the trusted PC..
Trusted PC: Select the PC to be the Trusted PC..
- 17 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.3 Access Control
The Access Control feature allows administrators to restrict the level of Internet Access available to PCs
on your LAN. With the default settings, everyone has unrestricted Internet access.
Select the desired options for the current group:
None - Nothing is blocked. Use this to create the least restrictive group.
Block all Internet access - All traffic via the WAN port is blocked. Use this to create the most restrictive
group.
Block selected Services - You can select which Services are to block. Use this to gain fine control over
the Internet access for a group.
Block by Schedule : If Internet access is being blocked, you can choose to apply the blocking only
during scheduled times. (If access is not blocked, no Scheduling is possible, and this setting has no
effect.)
Enable Trusted PCs : Enable the checkbox if you want to use this feature.
Set Trusted PCs : Click this button to add or remove PCs from the current Group.
See the following section for details of the Trusted PCs screen.
If you finish all setting about Access Control, remember to click “save” button.
- 18 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.4 Dynamic DNS
You can configure WNRT-61O to use DDNS service if you already have a registered DDNS account.
This free service is very useful when combined with the Virtual Server feature. It allows Internet users to
connect to your Virtual Servers using a URL, rather than an IP Address.
This also solves the problem of having a dynamic IP address. With a dynamic IP address, your IP
address may change whenever you connect, which makes it difficult to connect to you.
DDNS Services work as follows:
1. You must register for the service at one of the listed DDNS Service providers.
2. After registration, use the Service provider's normal procedure to obtain your desired Domain name.
3. Enter your DDNS data on the Wireless Broadband Router's DDNS screen, and enable the DDNS
feature.
4. The Wireless Broadband Router will then automatically ensure that your current IP Address is
recorded at the DDNS service provider's Domain Name Server.
5. From the Internet, users will be able to connect to your Virtual Servers (or DMZ PC) using your
Domain name, as shown on this screen.
- 19 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.5 Firewall Rules
The Firewall Rules screen allows you to define "Firewall Rules" which can allow or prevent certain traffic.
"Traffic" means incoming connection attempts, not packets.
By default:
All Outgoing traffic is permitted.
All Incoming traffic is denied.
Because of this default behavior, any Outgoing rules will generally Block traffic, and Incoming rules will
generally Allow traffic.
3.6.6 Firewall Services
If you wish to create a firewall rule, but the required service is not listed in the "Service" list, you can use
this feature to define the required service or services. Once created, these services will be listed in the
"Service" list, and can be used when creating Firewall Rules.
- 20 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.7 Virtual Servers
This feature, sometimes called Port Forwarding, allows you to make Servers on your LAN accessible to
Internet users. Normally, Internet users would not be able to access a server on your LAN because:
Your Server does not have a valid external IP Address.
Attempts to connect to devices on your LAN are blocked by the firewall in this device.
The "Virtual Server" feature solves these problems and allows Internet users to connect to your
servers, as illustrated below.
192.168.0.1
(LAN IP Address)
Wireless
Router
203.70.212.52
Web Server
(192.168.0.10)
FTP Server
(192.168.0.20)
(Internet IP Address)
Internet
Remote PC
Using Web Server
(http://203.70.212.52)
Remote PC
Using FTP Server
(ftp://203.70.212.52)
- 21 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Defaults : This will delete any Servers you have defined, and set the pre-defined Servers to use their
default port numbers.
Disable All : This will cause the "Enable" setting of all Virtual Servers to be set OFF.
Update Selected Server : Update the current Virtual Server entry, using the data shown in the
"Properties" area on screen.
Add as new Server : Add a new entry to the Virtual Server list, using the data shown in the "Properties"
area on screen. The entry selected in the list is ignored, and has no effect.
Delete : Delete the current Virtual Server entry. Note that the pre-defined Servers can not be deleted.
Only Servers you have defined yourself can be deleted.
Clear Form : Clear all data from the "Properties" area, ready for input of a new Virtual Server entry.
3.6.8 Options
This screen allows advanced users to enter or change a number of settings. For operation, there is no
need to use this screen or change any settings.
An example Options screen is shown below.
Respond to Ping : If checked, the wireless Router will respond to Ping (ICMP) packets received from
the Internet.
If not checked, Ping (ICMP) packets from the Internet will be ignored.Disabling the option provides a
slight increase in security.
MTU Size : Enter a value between 600 and 1500.
UPnP : UPnP (Universal Plug and Play) allows automatic discovery and configuration of equipment
attached your lan. UPnP is by support Windows ME , XP ,or later.
If enable , the device will be visible via UPnP.
If Disabled , the device will not be visible via UPnP.
Advertisement Period : Enter the desired value , in minutes. The valid range is from 1 to 1440.
Advertisement Time to Live : Enter the desired value , in hops. The valid range is from 1 to 255.
- 22 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.6.9 Schedule
This Schedule can be used for the Firewall Rules and the URL filter.
Day : Each day of week can scheduled independently.
Session 1 and Session 2: Two separate sessions or periods can be defined. Session 2 can be left blank
if not required.
Start Time : Enter the start using a 24 hour clock.
Finished Time : Enter finish using a 24 hour clock
Time Zone : In order to display your local time correctly, you must select your "Time Zone" from the list.
Adjust for Daylight Savings Time : If your region uses Daylight Savings Time, you must manually
check "Adjust for Daylight Savings Time" at the beginning of the adjustment period, and uncheck it at the
end of the Daylight Savings period.
Use this NTP Server : If you prefer to use a particular NTP server as the primary NTP server, check the
checkbox "Use this NTP Server" and enter the Server's IP address in the fields provided..
If this setting is not enabled, the default NTP Servers are used.
Current Time : This displays the current time on the Wireless Broadband Router, at the time the page is
loaded.
3.7 Administratoin
Normally, it is not necessary to use these screens, or change any settings. These screens and settings
are provided to deal with non-standard situations, or to provide additional options for advanced
users.
- 23 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7.1 PC Database
PC Database : This is the list of PCs shown when you select the "DMZ PC" or a "Virtual Server". This
database is maintained automatically, but you can add and delete entries for PCs which use a Fixed
(Static) IP Address.
The PC Database is used whenever you need to select a PC (e.g. for the "DMZ" PC).
It eliminates the need to enter IP addresses.
Also, you do not need to use fixed IP addresses on your LAN.
However, if you do use a fixed IP address on some devices on your LAN, you should enter details of
each such device into the PC database, using the PC Database screen.
PCs which are "DHCP Clients" are automatically added to the database, and updated as required.
By default, non-Server versions of Windows act as "DHCP Clients"; this setting is called "Obtain an IP
Address automatically".
The Wireless Broadband Router uses the "Hardware Address" to identify each PC, not the name or IP
address. The "Hardware Address" can only change if you change the PC's network card or adapter.
- 24 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7.2 Network Diagnostics
Ping this IP Address : Enter the IP address you wish to ping. The IP address can be on your LAN, or on
the Internet. Note that if the address is on the Internet, and no connection currently exists, you could get
a "Timeout" error. In that case, wait a few seconds and try again.
Ping Button : After entering the IP address, click this button to start the "Ping" procedure. The results will
be displayed in the Ping Results pane.
Internet name : Enter the Domain name or URL for which you want a DNS (Domain Name Server)
lookup. Note that if the address in on the Internet, and no connection currently exists, you could get a
"Timeout" error. In that case, wait a few seconds and try again.
Lookup Button : After entering the Domain name/URL, click this button to start the "DNS Lookup"
procedure.
Display : Click this button to display the internal routing table. This information can be used by Technical
Support and other staff who understand Routing Tables.
- 25 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7.3 Config File
This feature allows you to download the current settings from the WNRT-610, and save them to a file on
your PC.
You can restore a previously-downloaded configuration file to WNRT-610, by uploading it to the Wireless
Broadband Router.
This screen also allows you to set WNRT-610 back to its factory default configuration. Any existing
settings will be deleted.
An example Config File screen is shown below.
Backup Config : Use this to download a copy of the current configuration, and store the file on your PC.
Click Backup to start the download.
Restore Config : This allows you to restore a previously-saved configuration file back to the Wireless
Broadband Router.
Click Browse to select the configuration file, then click Restore to upload the configuration file.
WARNING!
Uploading a configuration file will destroy (overwrite) ALL of the existing settings.
Default Config : Clicking the Factory Defaults button will reset the Wireless Broadband Router to its
factory default settings.
WARNING!
This will delete ALL of the existing settings.
- 26 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.7.4 Logs
The Logs record various types of activity on the Wireless Broadband Router. This data is useful for
troubleshooting, but enabling all logs will generate a large amount of data and adversely affect
performance.
3.7.5 Remote Administration
If enabled, this feature allows you to manage the Wireless Broadband Router via the Internet.
Enable Remote Management : Check to allow administration/management via the Internet. (To connect,
see below).
If Disabled, this device will ignore Administration connection attempts from the Internet.
Current IP Address : This is the current address you will use when accessing this device from the
Internet. To connect, see details and an example below.
Port Number : Enter a port number between 1 and 65535. The default for HTTP (Web) connections is
port 80, but using port 80 will prevent the use of a Web "Virtual Server" on your LAN. So using a different
- 27 -
Download from Www.Somanuals.com. All Manuals Search And Download.
port number is recommended. The default value is 8080.
The port number must be specified in your Browser when you connect. See the following section for
details.
To connect from a remote PC via the Internet
Ensure your Internet connection is established, and start your Web Browser.
In the "Address" bar, enter "HTTP://" followed by the Internet IP Address of the Wireless Broadband
Router. If the port number is not 80, the port number is also required. (After the IP Address, enter ":"
followed by the port number.)
e.g.
This example assumes the WAN IP Address is 210.172.99.123, and the port number is 8080.
You will then be prompted for the login name and password for this device.
3.7.6 Upgrade Firmware
You can upgrade your WNRT-610 with new firmware in this screen. Please follow these instructions:
save it to your disk.
2. Click “Browse” and find out the location of the downloaded file.
3. Select the file and click “Upload” to update WNRT-610 to the latest firmware.
- 28 -
Download from Www.Somanuals.com. All Manuals Search And Download.
3.8 Log Out
If you want to leave the manage web browser from WNRT-610, Please click “Log Out”button.
Only one lan or wan manager can log in the WNRT-610 manage web browser.
If you do not manage the WNRT-610 for fewer minutes ,you must retype the password to manage the
web browser.
3.9 Restart
You can click :Restart: button to reboot WNRT-610.
- 29 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A TCP/IP Settings for PC
The network TCP/IP settings differ based on the computer’s operating system (2000/XP) and are as
follows.
Windows 2000
Double click on the “My computer” icon on the desktop. When “My computer” window opens, open the
“Control panel” and then open the “Network dialup connection” applet. Double click on the “Local area
network connection” icon. Select “Properties” to enter the TCP/IP setting window.
1. In the “Local area network status” window, click on “Properties.”
2. In the “Local area network connection” window, first select TCP/IP setting and then select
“Properties.”
3. Set both “IP address” and “DNS” to Automatic configuration.
Windows XP
Point the cursor and click the right button on the “My Network Place” icon. Select “properties” to enter the
TCP/IP setting window.
1.
2.
Set “IP address” to “Obtain an IP address automatically.”
Set “DNS” to “Obtain DNS server address automatically.”
- 30 -
Download from Www.Somanuals.com. All Manuals Search And Download.
- 31 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|