Download from Www.Somanuals.com. All Manuals Search And Download.
User’s Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international copy-
right laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2008
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no repre-
sentations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations and pend-
ing applications in other countries throughout the world.
All other product names used in this manual are the properties of their respective owners and are ac-
knowledged.
— ii —
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Important Safety Information
Congratulations on purchasing the Planar DLP® projector!
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause per-
sonal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information
ꢀ
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
ꢀ
ꢀ
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
ꢀ
ꢀ
ꢀ
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
— iii —
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Power Safety
ꢀ
ꢀ
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
ꢀ
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 35
for clear and safe instructions for this procedure. Before replacing the lamp:
ꢀ
ꢀ
Unplug the power cord.
Allow the lamp to cool for about one hour.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Cleaning the Projector
ꢀ
ꢀ
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
— iv —
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
Main Features
•
•
•
•
•
•
Lightweight unit, easy to pack away and transport.
Compatible with all major video standards including NTSC, PAL, and SECAM.
A high brightness rating allows for presentations in daylight or in lit rooms.
Supports resolutions up to SXGA at 16.7 million colors to deliver crisp, clear images.
Flexible setup allows for front, rear projections.
Line-of-vision projections remain square, with advanced keystone correction for angled
projections.
•
Input source automatically detected.
Register Your Planar Products Today
Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, reg-
ister your Planar product today. Visit our website to register your product at
Cables, Replacement Lamps and Accessories
To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or
products at http://www.planar.com/howtobuy
About this manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wher-
ever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting
the environment. It is suggested that you only print sections that are relevant to your needs.
— v —
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Table of Contents
GETTING STARTED........................................................................................................................................................... 1
PACKING CHECKLIST........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS............................................................................................................................................... 2
Front-right View ............................................................................................................................................................ 2
Top view—On-screen Display (OSD) buttons and LEDs....................................................................................... 3
Rear view....................................................................................................................................................................... 4
Bottom view................................................................................................................................................................... 5
REMOTE CONTROL PARTS ................................................................................................................................................... 6
REMOTE CONTROL OPERATING RANGE............................................................................................................................... 8
PROJECTOR AND REMOTE CONTROL BUTTONS.................................................................................................................... 8
Remote Control............................................................................................................................................................. 8
SETUP AND OPERATION................................................................................................................................................. 9
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................... 9
CONNECTING INPUT DEVICES............................................................................................................................................ 10
STARTING AND SHUTTING DOWN THE PROJECTOR............................................................................................................. 11
SETTING AN ACCESS PASSWORD (SECURITY LOCK).......................................................................................................... 13
ADJUSTING THE PROJECTOR LEVEL................................................................................................................................... 15
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ................................................................................................................ 16
ADJUSTING THE VOLUME .................................................................................................................................................. 17
ON-SCREEN DISPLAY (OSD) MENU SETTINGS...................................................................................................... 18
OSD MENU CONTROLS ..................................................................................................................................................... 18
Navigating the OSD ................................................................................................................................................... 18
SETTING THE OSD LANGUAGE.......................................................................................................................................... 19
OSD MENU OVERVIEW ..................................................................................................................................................... 20
OSD SUB-MENU OVERVIEW ............................................................................................................................................. 21
IMAGE MENU..................................................................................................................................................................... 22
Advanced Feature...................................................................................................................................................... 23
Color Manager............................................................................................................................................................ 24
COMPUTER MENU.............................................................................................................................................................. 25
VIDEO/AUDIO MENU ......................................................................................................................................................... 26
Audio............................................................................................................................................................................ 27
INSTALLATION I MENU...................................................................................................................................................... 28
INSTALLATION II MENU .................................................................................................................................................... 29
Advanced Feature...................................................................................................................................................... 30
OSD Menu Setting ..................................................................................................................................................... 31
Peripheral Test ........................................................................................................................................................... 32
Lamp Hour Reset ....................................................................................................................................................... 33
Factory Reset.............................................................................................................................................................. 34
Status........................................................................................................................................................................... 34
MAINTENANCE AND SECURITY.................................................................................................................................. 35
REPLACING THE PROJECTION LAMP................................................................................................................................... 35
Resetting the Lamp.................................................................................................................................................... 38
CLEANING THE PROJECTOR................................................................................................................................................ 39
Cleaning the Lens ...................................................................................................................................................... 39
Cleaning the Case...................................................................................................................................................... 39
USING THE KENSINGTON® LOCK ...................................................................................................................................... 40
TROUBLESHOOTING...................................................................................................................................................... 41
COMMON PROBLEMS AND SOLUTIONS ............................................................................................................................... 41
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 41
LED ERROR MESSAGES .................................................................................................................................................... 42
IMAGE PROBLEMS.............................................................................................................................................................. 42
LAMP PROBLEMS ............................................................................................................................................................... 43
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 43
AUDIO PROBLEMS ............................................................................................................................................................. 43
— vi —
Download from Www.Somanuals.com. All Manuals Search And Download.
Preface
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 43
SPECIFICATIONS............................................................................................................................................................. 44
Input Connectors........................................................................................................................................................ 44
PROJECTION DISTANCE VS. PROJECTION SIZE ................................................................................................................... 44
Projection Distance and Size Table......................................................................................................................... 44
TIMING MODE TABLE ........................................................................................................................................................ 45
PROJECTOR DIMENSIONS ................................................................................................................................................... 47
REGULATORY COMPLIANCE....................................................................................................................................... 48
FCC WARNING.................................................................................................................................................................. 48
SAFETY CERTIFICATIONS................................................................................................................................................... 48
EN 55022 WARNING ......................................................................................................................................................... 48
— vii —
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Packing Checklist
Carefully unpack the projector and check that the following items are included:
PR6022 DLP projector
Remote control
(with one 3V CR2025 battery)
RGB cable
Power cord
RGB to Component Adapter
(Optional)
Quick Start Guide
CD-ROM
Carrying case
(This User’s manual)
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
Caution:
Avoid using the projector in dusty environments.
– 1 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Views of Projector Parts
Front-right View
Item
1.
Label
Description
See page:
Ventilation opening
To keep the projector lamp cool
Height-adjuster button Push to release height adjuster
2.
Height adjuster
Lens cap
Adjusts level of projector
3.
Covers lens to protect when not in use
Receiver for IR signal from remote control
Remove lens cap before use
4.
IR receiver
Lens
5.
6.
Focus ring
Zoom ring
Focuses the projected image
7.
Enlarges the projected image
8.
Function keys
9.
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
– 2 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Top view—On-screen Display (OSD) buttons and LEDs
Item
1.
Label
Description
See page:
Turns the projector On or Off
(Power)
▲ (Up cursor)
Navigates and changes settings in the OSD
2.
3.
Green
Off
Power On
Power LED
Power Off (AC Off)
Error code
Flashing
On
System over temperature
Normal State
Over Temp LED
4.
5.
Off
Orange
Lamp is ready to be powered-on.
Ready LED
Menu
Lamp not ready (Warm-up/shutting down/cooling)
Flashing
Open and exits the OSD buttons
6.
7.
8.
9.
◄ (Left cursor) /
Source
Detects the input device
Navigates and changes settings in the OSD
▼ (Down cursor)
Navigates and changes settings in the OSD
► (Right cursor) /
Auto
Optimizes image size, position, and resolution
Navigates and changes settings in the OSD
— 3 —
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Rear view
Item
1.
Label
Description
See page:
AC IN
Connect the power cable
Connect the USB cable from a computer
(service only)
USB (Service Only)
2.
Connect the AUDIO CABLE from the input device
Connect the S-VIDEO CABLE from a video device
Connect the VIDEO CABLE from a video device
AUDIO
S-VIDEO
VIDEO
3.
4.
5.
Connect the RGB CABLE from a computer and
components
VGA
6.
7.
Secure to permanent object with a Kensington®
Lock system
(Security Lock)
Note:
If your video equipment has both S-VIDEO and RCA jacks (composite video) connect to the
S-VIDEO connector. S-VIDEO provides a better quality signal.
– 4 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Bottom view
Item
Label
Description
See page:
Lamp cover
Remove when changing the lamp.
1.
2.
Adjuster drops down when adjuster button is
pushed.
Height adjustor
Lens cap hook
Tilt adjustor
To fasten the lens cap cover.
3.
4.
Rotate adjuster lever to adjust angle position.
Contact your dealer for information on mounting the projector on a
ceiling
Ceiling support holes
5.
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
— 5 —
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluores-
cent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between
the remote control and the projector is obstructed, you can bounce the signal off certain reflective sur-
faces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on the
remote control. This user’s manual describes the functions based on the remote control.
– 6 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Item
1.
Label
Description
See page:
Up cursor
Navigates and changes settings in the OSD
Changes settings in the OSD
Enter
2.
Power
Turns the projector On or Off
3.
Right cursor
Volume +
Volume -
Mute
Navigates and changes settings in the OSD
Increase volume
4.
5.
Decrease volume
6.
Mutes the built-in speaker
7.
Freeze
Freeze/unfreezes the on-screen picture
Detects the input device
8.
Source
9.
Auto
Auto adjustment for frequency, tracking, size, position
Corrects image-trapezoid (wider top) effect
Corrects image trapezoid (wider bottom) effect
Navigates and changes settings in the OSD
Navigates and changes settings in the OSD
Opens the OSD
10.
11.
12.
13.
14.
15.
Keystone top
Keystone bottom
Down cursor
Left cursor
Menu
— 7 —
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or
the rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and
15 degrees above or below the projector level. If the projector does not respond to the remote control,
move a little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are lim-
ited in use. The following illustration shows the corresponding buttons on the remote control and on
the projector.
Remote Control
Some buttons on the projector have multiple functions. For example, item 3/6/7 on the projector func-
tions as the keystone button and as the down cursor key.
– 8 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup and Operation
Inserting the Remote Control Batteries
Remove the battery compartment
1.
cover by sliding the cover in the di-
rection of the arrow (A). Pull out the
cover (B).
Insert the battery with the positive
side facing up.
2.
Replace the cover.
3.
Caution:
1. Only use a 3V lithium battery (CR2025).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the battery when not using the projector for prolonged periods.
– 9 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Connecting Input Devices
A PC or notebook computer and video devices can be connected to the projector at the same time. Video
devices include DVD, VCD, and VHS players, as well as movie camcorders and digital still cameras.
Check the user manual of the connecting device to confirm it has the appropriate output connector.
Item
A
Label
Description
USB (Service Only)
Connect the USB cable from a computer (service only).
Connect the audio cable from the computer’s audio-out connector.
Connect the audio cable (mini jack-to-RCA x 2) from a video device.
AUDIO
S-VIDEO
VIDEO
B
Connect the S-video cable from a video device.
Connect the video cable from a video device.
C
D
Connect the RGB cable from a computer.
Connect DVD input YCbCr / YPbPr, through optional RGB to
COMPONENT ADAPTOR.
VGA
E
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
– 10 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Starting and Shutting down the Projector
Connect the power cord to the
projector. Connect the other end to
a wall outlet.
1.
The
Power and Ready LEDs on
the projector light.
Turn on the connected devices.
2.
3.
Ensure the Ready LED displays a
solid orange and not a flashing or-
ange. Then press the
Power
button to turn on the projector.
The projector splash screen displays
and connected devices are de-
tected.
See Setting an Access Password
If more than one input device is con-
nected, press the Source button
and use ▲▼ to scroll among de-
vices.
4.
(Component is supported through
the RGB to Component adapter.)
•
RGB: Analog RGB
Component: DVD input YCbCr / YPbPr, or HDTV
input YPbPr via HD15 connector
•
•
Composite Video: Traditional composite video
S-Video: Super video (Y/C separated)
– 11 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
When the “Power Off? /Press
5.
Power again” message appears,
press the Power button. The projec-
tor turns off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until the Ready LED stops flashing–indicating the projector has
cooled down.
– 12 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projec-
tor. When enabled, the password must be entered after you power on the projector. (See Navigating
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
Press the Menu button to open the
OSD menu.
1.
Press the cursor ◄► button to move
to the Installation I menu.
2.
Press the cursor ▲▼ button to select
Security Lock.
3.
Press the cursor ◄► button to enable
or disable security lock function.
4.
A password dialog box automatically
appears.
– 13 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
You can use the cursor buttons
▲▼◄►
5.
either on keypad or IR remote control
for password entry. You can use any
combination including the same arrow
five times, but not less than five.
Press the cursor buttons in any order
to set the password. Push the Menu
button to exit the dialog box.
The password confirm menu appears
6.
when user presses the power-on key
in case the Security Lock is enabled.
Enter the password in the order you
set it at step 5. In case you forget the
password, please contact the service
center.
Service center will validate the owner
and help reset the password.
– 14 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:
•
•
•
The projector table or stand should be level and sturdy.
Position the projector so that it is perpendicular to the screen.
Ensure the cables are in a safe location. You could trip over them.
To raise the level of the projector, lift the projector [A] and press the height-adjuster
button [B].
1.
The height adjuster drops down [C].
To lower the level of the projector, press the height-adjuster button and push down on
the top of the projector.
2.
3.
To adjust the angle of the picture, turn the tilt-adjuster [D] right or left until the
desired angle has been achieved.
– 15 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Adjusting the Zoom, Focus and Keystone
Use the Image-zoom
1.
control (on the projector
only) to resize the pro-
jected image and
B
screen size
.
Use the Image-focus
control (on the projector
only) to sharpen the
2.
3.
A
projected image
.
Remote control and OSD panel
The keystone control
appears on the display.
– 16 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Adjusting the Volume
Press the Volume +/-
buttons on the remote
control.
1.
The volume control
appears on the display.
Press the Left or Right
2.
Cursor buttons on the
keypad to adjust Vol-
ume +/-.
Press the Mute button
3.
to turn off the volume
(This feature is avail-
able only on the
remote).
– 17 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
On-Screen Display (OSD) Menu Settings
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the buttons on the top of the projector to navigate
and make changes to the OSD. The following illustration shows the corresponding buttons on the re-
mote control and on the projector.
1. To enter the OSD, press the
Menu button.
2. There are five menus. Press
the cursor ◄► button to
move through the menus.
3. Press the cursor ▲▼ button
to move up and down in a
menu.
4. Press ◄► to change values
for settings.
5. Press Menu to close the
OSD or leave a submenu.
Note:
Depending on the video source, not all items in the OSD are available. For example, the Horizon-
tal/Vertical Position items in the Computer menu can only be modified when connected to a PC.
Items that are not available cannot be accessed and are grayed out.
– 18 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the Menu button. Press the cursor ◄► button to navigate to Installation I.
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ◄► button until the language you want is highlighted.
4. Press the Menu button twice to close the OSD.
– 19 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Image Menu
Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Image
Menu. Press the cursor ▲▼ button to move up and down in the Image menu. Press ◄► to change
values for settings.
Item
Display Mode
Brilliant Color
Brightness
Contrast
Description
Press the cursor ◄► button to set the Display Mode.
Press the cursor ◄► button to adjust the Brilliant Color value.
Press the cursor ◄► button to adjust the display brightness.
Press the cursor ◄► button to adjust the display contrast.
Press the cursor ◄► button to adjust the display sharpness level.
Press the cursor ◄► button to adjust the gamma correction of the display.
Sharpness
Gamma
Press
Advanced
Reset
Press
(Enter) / ► to reset all settings to default values.
– 22 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Image menu. Press ▼▲
to move to the Advanced menu and then press Enter or ►. Press ▼▲ to move up and down in the
Advanced menu.
Item
Description
Press the cursor ◄► button to adjust the color space.
(Range: Auto – RGB – YPbPr- YCbCr)
Color Space
Press the cursor ◄► button to adjust the color temperature.
(Range: 6500 °K ~ 10500 °K)
Color Temperature
Color Manager
Press
(Enter) / ► to enter the color manager menu. (Range: Red-
– 23 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Color Manager
Press
(Enter) / ► to enter the Color Manager sub menu.
Item
Description
Select to enter the Red Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Red
Select to enter the Green Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Green
Blue
Select to enter the Blue Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the Cyan Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Cyan
Select to enter the Magenta Color Manager.
Press the ◄► buttons to adjust the Hue, Saturation, and Gain.
Magenta
Yellow
White
Select to enter the Yellow Color Manager.
Press the◄► buttons to adjust the Hue, Saturation, and Gain.
Select to enter the White Color Manager.
Press the ◄► buttons to adjust the Red, Green, and Blue.
– 24 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Computer Menu
Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Com-
puter menu. Press the cursor ▲▼ button to move up and down in the Computer menu. Press ◄►
to change values for settings.
Item
Horizontal Position
Vertical Position
Frequency
Description
Press the cursor ◄► button to adjust the display position to left or right.
Press the cursor ◄► button to adjust the display position to up or down.
Press the cursor ◄► button to adjust the A/D sampling clock.
Press the cursor ◄► button to adjust the A/D sampling dot.
Tracking
Press
and position.
(Enter) / ► to automatically adjustment for phase, tracking, size
Auto Image
– 25 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Video/Audio Menu
Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the
Video/Audio menu. Press the cursor ▲▼ button to move up and down in the Video/Audio menu.
Press ◄► to change values for settings.
Item
Description
Press the ◄► buttons to enable or disable the Automatic Gain Control for
video source.
Video AGC
Video Saturation
Video Tint
Film Mode
Video Overscan
Audio
Press the ◄► buttons to adjust the video saturation.
Press the ◄► buttons to adjust the video tint/hue.
Press the ◄► buttons to select a different film mode.
Press the ◄► buttons to enable or disable video over scan.
Press
Press
Reset
(Enter) / ► to reset all settings to default values.
Note:
Video jagging may occur when playing interlace video. To overcome this issue, open the
Video / Audio menu and adjust the Film Mode feature.
– 26 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Installation I Menu
Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Installa-
tion I menu. Press the cursor ▲▼ button to move up and down in the Installation I menu. Press
◄► to change values for settings.
Item
Description
Language
Press the cursor ◄► button to select a different localization Menu.
Press the cursor ◄► button to select different color to blank the screen.
Press the cursor ◄► button to choose from four projection methods:
Press the cursor ◄► button to enable or disable security lock function.
Press the cursor ◄► button to adjust the video aspect ratio.
Blank Screen
Projection
Security Lock
Aspect Ratio
Keystone
Press the cursor ◄► button to adjust the display keystone.
Press the cursor ◄► button to adjust the Digital Zoom menu.
(Range: -10 ~ +10)
Digital Zoom
Reset
Press
(Enter) / ► to reset all settings to default values
(expect Language and Security Lock).
– 28 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Installation II Menu
Press the Menu button to open the OSD menu. Press the cursor ◄► button to move to the Installa-
tion II menu. Press the cursor ▲▼ button to move up and down in the Installation II menu. Press
◄► to change values for settings.
Item
Description
Press the cursor ◄► button to enable or disable automatic source detection.
(Range: On ~ Off)
Auto Source
Auto Power Off
(min.)
Press the cursor ◄► button to enable or disable automatic shutdown of lamp
when no signal.
Press the cursor ◄► button to enable or disable automatic power On when
AC power is supplied.
Auto Power On
Fan Speed
Press the cursor ◄► button to toggle between Normal and High fan speeds.
Note: We recommend selecting high speed in high temperatures, high humid-
ity, or high
altitude areas.
Press the cursor ◄► button to select the lamp mode for higher brightness or
lower brightness to save lamp life.
Lamp Mode
Press
Advanced
Factory Reset
Status
Press
Press
(Enter) / ► to reset all items to factory preset values.
– 29 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Advanced Feature
Press the Menu button to open the OSD menu. Press ◄► to move to the Installation II menu.
Press ▲▼ to move to the Advanced menu and then press Enter or ►. Press ▲▼ to move up and
down in the Advanced menu. Press ◄► to change values for settings.
Item
Description
OSD Menu Set-
ting
Peripheral Test
Lamp Hour Re-
set
– 30 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
OSD Menu Setting
Item
Description
Menu Position
Translucent Menu
Menu Display
Press ◄► button to select different OSD location.
Press ◄► button to select OSD background translucent level.
Press ◄► button to select OSD timeout delay.
– 31 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Peripheral Test
Item
Description
Remote Control Test
Press
(Enter) / ► and follow the on-screen prompts to carry out the
Remote Control Test.
Press the Menu button twice to return to the Peripheral Test menu.
USB Test
Press
Test.
(Enter) / ► and follow on-screen prompts to carry out the USB
Press the Menu button to return to the Peripheral Test menu.
Button Test
Press (Enter) / ► and follow the on-screen prompts to carry out the
Button (display panel) Test.
Press the Menu button twice to return to the Peripheral Test menu.
Color Test
Press
Test.
(Enter) / ► and follow on-screen prompts to carry out the Color
Press the Menu button to return to the Peripheral Test menu.
Sound Test
Press (Enter) / ► and follow on-screen prompts to carry out the
Sound Test.
Press the Menu button to return to the Peripheral Test menu.
– 32 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Factory Reset
Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the Factory
Reset sub menu and press
(Enter) / ► to reset all the menu items to the factory default values
(expect Language and Security Lock).
Status
Press the cursor ▲▼ button to move up and down in the Installation II menu. Select the
Installation II sub menu and press
(Enter) / ► to enter the Status sub menu.
Item
Description
Active Source
Display the activated source.
Video Informa-
tion
Displays resolution/video information for RGB source and color standard for
Video source.
Lamp hour used information is displayed. Eco and Normal counters are sepa-
rated.
Lamp Hours
– 34 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Security
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. It should only be replaced with a certified
replacement part, which you can order from your local dealer.
Important:
a. The projection lamp used in this product contains a small amount of mercury.
b. Do not dispose this product with general household waste.
c. Disposal of this product must be carried out in accordance with the regulations of your local
authority.
Warning:
Be sure to turn off and unplug the projector at least 30 minutes before replacing the lamp. Failure to
do so could result in a severe burn.
Loosen the two captive
screws on the lamp com-
1.
partment cover (A).
Remove the lamp com-
partment cover (B).
2.
– 35 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Remove the two screws
from the lamp module (A).
3.
Lift the module handle up
(B).
4.
Pull firmly on the module
handle to remove the lamp
module.
5.
– 36 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Reverse steps 1 to 5 to
install the new lamp mod-
ule. While installing, align
the lamp module with the
connector and ensure it is
level to avoid damage.
6.
Note: The lamp module
must sit securely in place
and the lamp connector
must be connected prop-
erly before tightening the
screws.
– 37 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Resetting the Lamp
After replacing the lamp, you should reset the lamp hour counter to zero. Refer to the following:
Press the Menu button to open
the OSD menu.
1.
Press the cursor ◄► button to
2.
move to the Installation II menu.
Press the cursor button to move
down to Advanced.
Press the cursor ▼▲ button to
move down to Lamp Hour Reset.
3.
Press the cursor ► or Enter
button.
4.
A message screen appears.
Press ▼▲◄► buttons to reset
the lamp hour.
5.
Press the Menu button to get
back to Installation II.
6.
– 38 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 30 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the pro-
jector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent (such as used to wash dishes), and then wipe
the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
– 39 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Using the Kensington® Lock
If you are concerned about security, attach the projector to a permanent object with the Kensington
slot and a security cable.
Note:
Contact your vendor for details on purchasing a suitable Kensington security cable.
The security lock corresponds to Kensington’s MicroSaver Security System. If you have any com-
ment, contact: Kensington, 2853 Campus Drive, San Mateo, CA 94403, U.S.A. Tel: 800-535-4242,
– 40 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Common problems and solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact your dealer for assistance.
Often after time spent troubleshooting, the problem is traced to something as simple as a loose con-
nection. Check the following before proceeding to the problem-specific solutions.
•
•
•
•
•
•
Use some other electrical device to confirm that the electrical outlet is working.
Ensure the projector is turned on.
Ensure all connections are securely attached.
Ensure the attached device is turned on.
Ensure a connected PC is not in suspending mode.
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing an Fn-key combination on the notebook.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pin point the problem and thus avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting: The information may be useful when call-
ing for technical support or for passing on to service personnel.
– 41 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
LED Error Messages
Over Temp
LED
Error Code Messages
Power LED Blink
Ready LED Blink
Over temperature
Thermal break status error
Lamp error
0
ON
0
0
4
0
0
1
2
3
0
0
0
5
6
6
6
7
8
9
0
Fan1 error
0
Fan2 error
0
Fan3 error
0
Lamp door open
DMD error
0
0
Color wheel error
0
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before re-
starting the projector. If the Power or Ready LEDs are still blinking or the Over Temp LED is lit,
contact your service center.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
Problem: The image is blurred
3. Adjust the Focus on the projector.
4. Press the Auto button on the remote control or projector.
5. Ensure the projector-to-screen distance is within the 10-meter (33-feet) specified range.
6. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone button on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Installation I menu of the OSD.
Problem: The image is streaked
1. Set the Frequency and Tracking settings on the Computer menu of the OSD to the
default settings.
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
Problem: The image is flat with no contrast
Adjust the Contrast setting on the Image menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the Image menu of the OSD.
– 42 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the Power LED is green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Re-plug power cord. When the Ready LED
is on, press the power button.
2. Replace the lamp module.
3. Put the old lamp back in the projector and have the projector serviced.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other Infrared-enabled devices in the vicinity.
7. Have the remote control serviced.
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
Check the audio cable connection.
1. Test the source audio output with other speakers.
2. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem, you should have the projector serviced. Pack the projector in
the original carton. Include a description of the problem and a checklist of the steps you took when
trying to fix the problem: The information may be useful to service personnel. For servicing, return the
projector to the place you purchased it.
– 43 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Specifications
Input Connectors
VGA
USB (service only)
PC
Composite video (RCAx1)
S-Video (Mini-DIN)
Mini-jack
Video
Audio
Security
Kensington slot
Projection Distance vs. Projection Size
Projection Distance and Size Table
PR6022
Tele
4.47
140.94 175.98 351.97 60.63
Wide
m
1.34
52.76
30
3.58
8.94
1.54
3.09
3.86
11.58
Distance
feet
121.65 151.97 455.91
Diagonal
Keystone
inches
degree
mm
80
100
200
40
80
100
300
12.3
457
12.3
1219
47.99
1626
64.01
171
12.3
1524
60.00
2032
80.00
213
12.3
1864
73.39
3762
14.2
610
24.02
813
14.2
1219
47.99
1626
64.01
171
14.2
1524
60.00
2032
80.00
213
14.2
4572
180.00
6096
160.00
640
Image Height
Image Width
A (Offset)
inches
mm
17.99
610
inches
mm
24.02
64
148.11 32.01
427
85
inches
2.52
6.73
8.39
16.81
3.35
6.73
8.39
25.20
– 44 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
Timing Mode Table
The projector can display several resolutions. The following table outlines the resolutions that can be
displayed by the projector.
H-Sync
(KHz)
V-Sync
(Hz)
Composite /
S-Video
Signal
NTSC
Resolution
Component RGB
—
15.734
15.625
37.9
60.0
50.0
85.0
85.0
85.0
60.0
72.0
75.0
85.0
56.0
60.0
72.0
75.0
85.0
60.0
70.0
75.0
85.0
60.0
60.0
75.0
60.0
O
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
PAL/SECAM
—
O
640 x 350*
640 x 400*
720 x 400*
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1440 x 900
1280 x 1024
1280 x 1024
1400 x 1050
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
37.9
37.9
31.5
37.9
37.5
43.3
35.2
37.9
48.1
VESA
46.9
53.7
48.4
56.5
60.0
68.7
55.6
63.98
79.98
65.3
– 45 –
Download from Www.Somanuals.com. All Manuals Search And Download.
DLP® Projector – User’s Manual
H-Sync
(KHz)
V-Sync
(Hz)
Composite /
S-Video
Signal
Resolution
Component RGB
35.0
49.725
60.24
66.68
74.55
75.0
75.06
60
640 x 480
832 x 624
1024 x 768
1152 x 870
480i
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
O
O
O
O
O
O
O
O
O
O
Apple Mac
O
68.68
O
15.734
15.625
31.469
31.25
37.5
—
—
—
—
—
—
—
—
SDTV
EDTV
576i
50
480p
60
576p
50
720p
50
720p
45.0
60
HDTV
1080i
33.8
60
1080i
28.1
50
O: Frequency supported
—: Frequency not supported
* : Displayable level
The resolution of the panel is 1024 x 768. Resolution other than native resolution may display with
uneven size of text or lines.
HDTV timing: DVD player (main source), VG828 (secondary source).
– 46 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Compliance
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pur-
suant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communica-
tions. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
Safety Certifications
FCC-B, UL, cUL, CE class B, CB and C-Tick.
EN 55022 Warning
This is a Class B product. In a domestic environment, it may cause radio interference, in which case
the user may be required to take adequate measures. The typical use is in a conference room, meet-
ing room, or auditorium.
– 48 –
Download from Www.Somanuals.com. All Manuals Search And Download.
Planar Systems, Inc.
Corporate Headquarters
1195 NW Compton Drive
Beaverton, OR 97006-1992
Planar Customer Support
Telephone:
US: 1-866-PLANAR1 (866) 752-6271
Outside US: (503) 748-5799
E-mail: [email protected]
24/7 Technical Support
© 2008 Planar Systems, Inc. Planar is a registered trademark of Planar Systems, Inc.
Other brands and names are the property of their respective owners.
Technical information in this document is subject to change without notice
P/N: 020-0915-00A
Download from Www.Somanuals.com. All Manuals Search And Download.
|