LC1200R High-Bright Monitor
USER’S MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
7.3
7.4
Display Uniformity
23
23
Display Chromaticity
8
DISPLAY COSMETICS
Black Display Picture Mode
White Display Picture Mode
24
24
8.1
8.2
24
9
REGULATORY AGENCY REQUIREMENTS
Safety Certification
24
24
24
25
25
25
26
9.1
9.2
9.3
9.4
9.5
9.6
CE Marketing
RFI Emission Certification
System Transient Disturbance Requirements
Labeling
ROHS Compliance
10 RELIABILITY
26
26
10.1
10.2
Design Workload
MTBF
26
11 DESCRIPTION OF WARRANTY
12 SUPPORT AND SERVICE
13 GLOSSARY OF TERMS
26
27
28
LC1200R User’s Guide 021-0183-00 Rev A
3 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introduction
This document defines the electromechanical parameters and operating characteristics for The
Planar Systems, Inc. LC1200R, Very High Bright, 12.1” Active Matrix Liquid Crystal Display (AMLCD)
based product. It is intended for operation as a component in a high ambient light, outdoor system.
The LC1200R has a scaleable video format capable of displaying a minimum of VGA (640 x 480)
through XGA (1024 x 768) input resolution.
The LC1200R can be driven directly from the standard analog video graphics adapter (VGA) output
on a personal computer (PC). It consists of a 12.1" viewable diagonal LCD panel with optical
elements, cold-cathode fluorescent backlight, backlight inverter board, and LCD controller board. A
tethered photodiode provides automatic brightness control. Cooling fans are provided to cool the
back of the LCD module. If used in direct sunlight, it is the system designer’s responsibility to provide
an enclosure that directs the airflow, across the front of the display. Two (2) chassis mounted
connectors at the rear provide for video signal and 12 V DC power input connections. The enclosure
is aluminum for added cooling and ease of installation.
2 Basic Construction
2.1 LCD Display
2.1.1 LCD Panel – Physical Image Characteristics
The LC1200R incorporates an matrix display with the following features:
LCD Size:
307.5mm [12.11in] diagonal
Active Area:
Pixel Format:
Pixel Pitch:
246.0mm [9.69in] by 184.5mm [7.26in]
800 (H) x 600 (V) (1 full color pixel = R + G + B dots)
0.3075mm [0.012in] horizontal x 0.3075mm [0.012in] vertical
R,G,B vertical stripe
Pixel Arrangement:
LC1200R User’s Guide 021-0183-00 Rev A
4 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.2 Display format
The LC1200R is compatible with IBM VGA1 and VESA2 video standards. Its operating
frequency range is 31.5 kHz to 56.5 kHz horizontal; 60 Hz to 72 Hz (non-interlaced) vertical.
Specific video resolutions supported in Table 1
Table 1
Video Resolution
Number of Bits/Color
Number of Colors
640 x 400
640 x 480
720 x 400
800 x 600
1024 x 768
6
6
6
6
6
262,144
262,144
262,144
262,144
262,144
For IBM VGA1 modes, the LC1200R will accept 640 pixels horizontally; 400 or 480 lines
vertically and 800 pixels or 1024 pixels horizontally, 600 lines or 768 lines vertically for the
VESA2 modes. Figure 4 defines the video signal timing requirements.
The LCD controller board will automatically program itself, sensing incoming
horizontal/vertical frequencies and sync pulse polarities to completely “fill” the active display
area of the LC1200R with the video resolution being presented. Section 4.2 defines
parameters for video resolution detection by the LCD controller board.
Note: IBM VGA1 modes with border and the 720 x 400 video resolutions are excluded from
completely filling the active display area horizontally. Only the first 640 pixels will be
displayed.
2.2 Weight
The LC1200R has a lightweight aluminum enclosure and does not exceed 1.8 kg (4 lbs)
2.3 Mechanical
Size: 301mm x 265mm x 63 mm (11.9” x 10.4” x 2.5”)
See Planar Mechanical Outline drawing 076-0549-00 for more detail
Figure 1. View of Display
1 IBM VGA is a registered trademark of International Business Machines Corporation
2 VESA is a registered trademark of Video Electronics Standards Association.
LC1200R User’s Guide 021-0183-00 Rev A
5 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
301
246
Active area
4X M3 mnt holes
123
A
92.50
B
185
Active
area
235
152.15
Active Area
Center
63
83
Front View
Top of removable
standoff
Door to
User control
Connectors
Removable
Button
Board
4X M3 mnt
holes
Power
12 V
VGA
Conn
4X Fan inlet
57.5
185.08
2X M4
mounting holes
Rear View
Right View
LC1200R User’s Guide 021-0183-00 Rev A
6 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.4 Cooling Fans
Four (4) thermostatically controlled cooling fans are provided to cool the rear of the display. The
thermostat is set to turn the fans on when the video board temperature reaches 30° C. If the display
is used in direct sunlight, airflow must be directed across the front of the display or the display LCD
fluid may reach its clearing point, then the LC1200R will become temporarily unreadable.
2.5 Connectors
There are four connectors supplied as an integral part of the LC1200R.
2.5.1 Video Signal Connector
The LC1200R unit includes a chassis mounted 15-pin female mini D-Shell connector (AMP
748390-5 or equivalent) with socket contacts at the rear of the LC1200R. It is shielded for
electromagnetic interference (EMI) purposes. Refer to Section 4.1 for electrical connections.
2.5.2 DC Power Input Connector
The DC power input connector is a chassis mounted 2-pin connector (Molex Mini Fit Jr
Header 5569 Molex p/n 39-30-0020) with pin contacts at the side of the LC1200R. The
connections are insulated to prevent accidental contact.
2.5.3 Photodiode Connector
A 3-pin connector, Molex p/n 22-03-5035, is provided on the inverter board. The connector
accepts the cable assembly provided with the product that attaches to the provided
photodiode board.
2.5.4 Dimming Control Connector
A 5-pin connector, Molex p/n 22-03-5055, provides an analog input that can override the
automatic photodiode dimming and allows the backlight to be shut down using an inhibit
input.
2.5.5 Button Board Connector
The Button board can be mounted remotely or removed for better access when mounted
into the larger system.
2.6 Interface Cables
The display is shipped with a remote photo-sensor and cable, removable button board, and 6 ft VGA
interface cable. No other interface cables are provided. An external power supply brick is available
for purchase from Planar Systems, Inc.
LC1200R User’s Guide 021-0183-00 Rev A
7 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.7 Power Supply
The LC1200R does not ship with a power supply. It is recommended that the Planar Systems, Inc.
power adapter, part number 997-3066-00 (US) or 997-3067-00 (EU) be purchased with each unit.
Refer to Section 5 for power requirements.
2.8 LCD Controller Board
The LCD controller board incorporates components necessary to drive the LCD panel. Accepting VGA
and VESA video standards (Section 1.2), these video signals are digitized and processed for the LCD
panel. Due to the LCD panel’s fixed video resolution (800 x 600), the LCD controller board will
perform independent horizontal and vertical zoom and shrink scaling of specified video resolutions
less than or greater than the LCD panel’s video resolution to fully accommodate the LCD panel’s
capability.
Magnification or reduction of specified video resolutions to match the native LCD panel’s resolution
incorporates scaling algorithms minimizing aliasing and image distortion. The LCD controller board
includes the following characteristics:
•
Per pixel scaleable filters providing text sharpening and graphics smoothing for improved
image quality.
•
•
Color depth enhancement by performing spatial-temporal dithering reducing visual artifacts.
External controls. See User Controls (Page 18) for more information.
There are 5 connectors for 12 V fans located on the controller board. They are attached to a 30º C
thermostat.
2.9 Inverter Board
The inverter PCB drives the LC1200R’s 6 cold cathode fluorescent lamps (CCFL). It is capable of
automatic brightness control of the backlight. See User Controls (Page 17) for more information on
the dimming functions.
There are 4 connectors to power 12 V fans on the inverter PCB. They are on constantly.
2.10 Photodiode Board
A photodiode (Siemens BPW21) mounted on a separate circuit board is provided for sensing the
ambient light conditions. A cable (40 cm in length) is connected from the photodiode board to the
inverter board on the LC1200R.
Size: approximately 1 x 3 cm with two 3mm diameter mounting holes. Refer to mechanical outline
drawing for details
LC1200R User’s Guide 021-0183-00 Rev A
8 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
2.11 Button Board
The button board controls the user controls noted in Section 6.1 LCD Controller Board Controls It can
be removed or mounted in another area after initial adjustments are made.
3 Environmental
3.1 Temperature and Humidity
The LC1200R withstands operating and storage environmental conditions listed in Table 2.
Table 2
General Operating Shipping and Storage
Comments
Note 2,3,4,5
Temperature 0°C to 60°C
-20°C to 60°C
[-4°F to 140°F]
Note 1
[32°F to 140°F]
Relative
Note 1
Without
Humidity
Condensation
Tair is defined as ambient air temperature surrounding the LC1200R.
Note 1:
Note 2:
Note 3:
Tair
Tair
Tair
Tair
<
32°C : 95% RH maximum.
>
32°C : Absolute humidity content not to exceed 100% at 32oC.
-20°C < 48 hours
@
@
60°C < 168 hours
Slight background color changes are allowed depending on ambient temperature.
This phenomenon is reversible.
Note 4:
High temperature operation assumes the use of an enclosure that properly directs the
fan airflow
Note 5:
Upper operating temperature limit of 60°C is without solar loading.
Reference to "room ambient" is interpreted as 20°C - 25°C [68°F°-77°F] and applies throughout this
specification unless otherwise noted.
For product reliability predictions, the assumed temperature profile is:
Table 3
Operating Time
Temperature
0°C [32°F]
5%
90%
5%
30°C [86°F]
60°C [140°F]
LC1200R User’s Guide 021-0183-00 Rev A
9 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 Direct Sunlight Operation
This monitor will absorb approximately 45 W of solar power on the front surface of the display in a
typical setup when facing the sun directly. It is the integrator’s responsibility to design a system that
cools the front surface adequately. Otherwise, the display’s LC material will overheat and
temporarily phase change. The display will temporarily become black and unreadable.
3.3 Altitude
Maximum operating altitude is 3,000 meters [9,850 feet]. Maximum shipping and storage altitude is
12,000 meters [39,400 feet].
3.4 Mechanical Vibration and Shock
Note: Tests performed with unpackaged monitors are mounted in a Planar approved rigid retaining
fixture.
3.4.1 Vibration
Non-operating (sinusoidal):
10-200 Hz, 0.9g acceleration, 120 seconds per sweep for 15
minutes, three axes, (x, y, z).Following exposure unit shall
meet all performance requirements.
Non-operating (random):
10-200 Hz, 0.02g2/Hz, 10 min/axis, three (x, y, z).Following
exposure unit shall meet all performance requirements.
3.4.2 Shock
Non-operating:
30 g, > 2.5 ms duration, ½ sine, 1 shocks per axis. Following
exposure unit shall meet all performance requirements.
3.4.3 Shock Packaged Product
Non-operating:
30 inch free fall or simulated drop, 1 drop per side, 6 sides
and 1 drop per edge, 3 edges, 1 shocks per axis. With
accelerometer attached to center of product display screen,
a maximum of 50 G’s is allowed. Following exposure unit
shall meet all performance requirements.
Figure 2 Monitor unit orientation
Y (rear)
X (side)
DISPLAY
Z (bottom)
LC1200R User’s Guide 021-0183-00 Rev A
10 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Video Signal Requirements
4.1 Video Input Lines
The video signal connector that connects to the customer’s equipment is a female 15-pin connector
in a high density 9-pin D-Shell housing. Pin number assignments are defined in Table 4, and physical
layout as seen by the interface cable from user logic is shown in EErrrroorr!!RReeffeerreenncceessoouurrcceennoottffoouunndd..
The "NC" positions of this connector are not used for any purpose.
Table 4 Video Signal Connector – Pin Number Assignments
Pin Number Signal Name
Signal Name
1
2
3
4
Red Video
Green Video
Blue Video
Monitor Sense Line 3 (connected to Pin
10)
5
6
7
8
9
NC
Red video return
Green video return
Blue video return
NC
1
0
Signal Ground Reference
1
1
Monitor Sense Line 1 (connected to Pin
10)
1
2
Monitor Sense Line 2 (NC)
Horizontal Sync Input
Vertical Sync Input
NC
1
3
1
4
1
5
4.2 Signal Functions
4.2.1 Video Parameters
As seen by the video source, input resistance is 75-ohm, 10%; input capacitance at (150
MHZ) <10-pF. The video input signal must have a range of 0-mv to 714-mv (maximum)
where 0-mv is minimum luminance. Rise and fall times for the input signal (10% - 90%) will
be 5-ns (Figure 4). When terminated with a 75-ohm termination, the dark state (black level) is
LC1200R Use
11 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
defined as a level between 0-mv and 10-mv. The white state (full white) is dependent on the
VGA controller driving the LC1200R. Maximum levels may range from 550-mv to 714-mv.
Nominal 680-mv input voltage shall be defined as the default for supplier setup
requirements.
Displayed image intensity and colors will change linearly with the video analog input. This is
necessary to provide a uniform user color change on the screen in response to a uniformly
stepped analog input. The LC1200R is capable of resolving a minimum color range of
262,144 displayable colors (6 bit resolution for red, green and blue). This interpolates to 64
shades of gray (or color) at the red, green, and blue analog video inputs. Accomplishing
specified shades of gray requires a “Video Gain” control adjustment (Section 6.1) of red,
green, and blue analog input signals based on the maximum output level range previously
specified.
Figure 3
OVERSHOOT
HIGH
STEADY
LEVEL
POS
LOW
STEADY
LEVEL
NEG
RISE
TIME
FALL
TIME
4.2.2 Synchronization
Sync pulses for horizontal and vertical are TTL levels. Figure 4 TTL Allowable Signal Levels
defines the levels and drive current capabilities.
LC1200R User’s Guide 021-0183-00 Rev A
12 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 4 TTL Allowable Signal Levels
LC1200R User’s Guide 021-0183-00 Rev A
13 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
4.2.3 Mode Detection
The polarity of incoming horizontal/vertical frequencies and synchronization pulses define
the video resolution being presented. Video modes are listed in Table 5 Video Mode
Definitions.
Table 5 Video Mode Definitions
Video Mode Displayed
Image
Scanning
Frequency)
Sync Polarity
Resolution
Horizon Vertical Horizont Vertic
tal (KHz) (Hz)
al
-
-
-
al
+
-
IBM VGA
IBM VGA
IBM VGA
w/Border
IBM VGA
IBM VGA
w/Border
VESA
640 x 400
640 x 480
656 x 496
31.468
31.468
31.468
70
60
60
-
-
720 x 400
738 x 414
31.468
31.468
70
70
-
800 x 600
1024 x 768
48.077
56.48
72
70
+
-
+
-
VESA
4.2.4 Color Display Detection
The video signal source determines which type of display is connected to it based on the
state of the LC1200R sense lines. The LC1200R will indicate to the source that it is a "color
display" when the monitor sense line 1 (Pin 11) is physically connected to signal ground
reference (Pin 10) as defined by the wiring definitions ofTable 4 Video Signal Connector – Pin
Number Assignments.
4.3 Signal Quality
4.3.1 TTL Sync Pulse Signal Levels
Input levels for the horizontal and vertical sync pulses are defined in Figure 5.
4.3.2 Rise and Fall Times
Rise and fall times are the times required for signal transitions between 10% of Vs above low
steady level and 10% of Vs below high steady level where Vs is the peak-to-peak video input
signal level. The overshoot, if present, shall be exempted from establishing these high/low
levels referenced in. Both rise and fall times of each input signal shall be as follows:
Video:
Less than 5-ns
Less than 50-ns
Less than 100-ns
Horizontal Sync:
Vertical Sync:
LC1200R User’s Guide 021-0183-00 Rev A
14 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
4.4 Timing and Frequency
4.4.1 Video, Horizontal and Vertical Sync
Figure 6 illustrate video timing relationships the LC1200R operates within when the specified
video mode (Table 5 Video Mode Definitions) is applied.
Front Porch defines the time from end of active video data to the start of Horiz/Vert Sync
Pulse.
Back Porch defines the time from end of Horiz/Vert Sync Pulse to the start of active video
data.
Blanking is the total time comprising Front Porch, Back Porch and Sync Pulse time(s).
The horizontal sync circuitry synchronizes to horizontal frequencies of 31.468 KHz 0.5 KHz,
48.077KHz 0.5KHz, and 56.476KHz 0.5KHz. Horizontal sync pulse width variation is 1.813-
µsec to 3.813-µsec. The LC1200R will "sync" to the specified format vertical frequencies
between 60Hz and 72Hz without adjustment.
Absence of Horizontal and/or Vertical Sync will not damage the LC1200R.
4.5 Video Signal On-Off Sequences
The sequence for bringing up and removal of each video input signal can be in any sequence or
combination of input signals.
Table 6. Video Mode Timing Data
Video Modes
IBM VGA
VESA
Resolution
Video Clock
Horizontal Scan
Freq.
Horizontal Line
Period
640x400
25.175 MHz
640x480
25.175 MHz
800x600
50.000 MHz
1024x768
75.000 MHz
31.468 KHz
31.778 us 800
pixels
31.468 KHz
31.778 us 800
pixels
48.077 KHz
20.800 us 1040
pixels
56.476 KHz
17.707 us 1328
pixels
Horizontal
Blanking
6.356 us 160
pixels
6.356 us 160
pixels
4.800 us 240
pixels
4.053 um 304
pixels
Horizontal Sync
Pulse
2.400 us 120
3.813 us 96 pixels 3.813 us 96 pixels pixels
1.813 us 136
pixels
Horizontal Front
Porch
Horizontal Back
Porch
0.636 us 16 pixels 0.636 us 16 pixels 1.120 us 56 pixels 0.320 us 24 pixels
1.920 us 144
1.907 us 48 pixels 1.907 us 48 pixels 1.280 us 64 pixels pixels
Horizontal Active
Display
25.422 us 640
pixels
25.422 us 640
pixels
16.000 us 800
pixels
13.653 us 1024
pixels
Horizontal Sync
Polarity
-
-
-
-
Vertical Scan Freq. 70.087 Hz
59.94 Hz
16.683ms 525
lines
72.184 Hz
13.853 ms 666
lines
70.069
14.272 ms 806
lines
Vertical Frame
Period
14.268 ms 449
lines
Vertical Blanking
Vertical Sync
1.557 ms 49 line
0.064 ms 2 lines
1.430 ms 45 line
0.064 ms 2 lines
1.373 ms 66 lines
0.125 ms 6 lines
0.673 ms 38 lines
0.106 ms 6 lines
LC1200R User’s Guide 021-0183-00 Rev A
15 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Pulse
Vertical Front
Porch
0.381 ms 12 lines
0.318 ms 10 lines
0.770 ms 37 lines
0.053 ms 3 lines
Vertical Back
Porch
Vertical Active
Display
1.112 ms 35 lines
12.711 ms 400
lines
1.049 ms 33 lines
15.254 ms 480
lines
0.478 ms 23 lines
12.480 ms 600
lines
0.514 ms 29 lines
13.599 ms 768
lines
Vertical Sync
Polarity
-
-
-
-
Note: VGA border is not included in the active display time described above.
Note: For video mode 720 x 400 missing video rows and columns are allowed. This is a text
mode only. Performance is acceptable if characters as defined section 1.2.1 are legible.
Missing row or columns at the edge of the display is acceptable as long as characters remain
legible.
5 DC Power Input Requirements
5.1 DC Power Input Lines
The DC Power Input Connector consists of two (2) positions wired numerically and supplied attached
to the LC1200R as a chassis mounted connector per definitions listed in Table 7.
Table 7. DC Power Input Connector- Pin Assignments
PIN NUMBER
SIGNAL NAME
1
2
Positive Input Voltage (12V)
Return (GND)
The DC Power Input Connector is a 2 pin Molex Mini Fit Jr. Pin
number assignments are defined in Table 7; shown below is the
physical layout as seen by the interface cable from the DC power
source.
Figure 5
5.2 DC Input Voltage / Current
DC Input Voltage: 12 V DC nominal, +/- .4 V DC.
Over the specified input voltage range:
•
•
•
No loss of image synchronization occurs.
White display luminance level is within 10% of luminance at nominal input voltage.
DC Input Current: 4.3 amp maximum current draw (12.4-vdc applied) steady state conditions.
LC1200R User’s Guide 021-0183-00 Rev A
16 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
The LC1200R is not damaged by input voltages ranging from 0-vdc to 12.4-vdc.
5.3 Power On-Off Sequences
The LC1200R will automatically return to normal operation upon resumption of power after a power
loss.
6 User Controls
6.1 LCD Controller Board Controls
The display comes from the factory adjusted for the supported modes. When using these modes,
adjustment should not be necessary. However, if it should become necessary, or a non-supported
mode is selected, the following controls are available for adjustment.
There are 4 push buttons located on the back of the display, which allow adjustment of the displayed
image.
The provided controls are:
Name
Dot Clk -
Dot Clk +
Horiz
Vert
Gain
Function
Clock Frequency/Phase Decrease
Clock Frequency/Phase Increase
Horizontal Position Adjustment
Vertical Position Adjustment
Video Gain Adjustment
The Clock Frequency /Phase adjustments are dual function buttons. The clock frequency adjustment
is used to change the horizontal size of the displayed image. The Phase adjustment is used to
minimize the pixel ‘noise’ or ‘jitter’. The phase allows for 32 positions of phase control. If the button is
held down, the clock frequency is adjusted up or down 1 clock each time the phase control register
rolls over. To adjust the clock frequency further, continue to hold the button down. If phase
adjustment is desired, it’s best to use single presses.
The Horizontal Position is adjusted by holding down the Horiz button. The position will shift by 1
column for each press. If the button is held down, the position will continuously adjust until released.
The direction of the adjustment depends on the direction of the last adjustment. The direction will
continue to be true until the maximum or minimum adjustment is reached. At this point, the
direction will reverse.
The Vertical Position is adjusted by holding down the Vert button. The position will shift by 1 column
for each press. If the button is held down, the position will continuously adjust until released. The
direction of the adjustment depends on the direction of the last adjustment. The direction will
continue to be true until the maximum or minimum adjustment is reached. At this point, the
direction will reverse
LC1200R User’s Guide 021-0183-00 Rev A
17 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
The Gain adjustment is to allow the full scale of the input video to be utilized. The direction of this
adjustment will reverse when a limit is reached. For example, it will adjust from maximum to
minimum, then reverse and go from minimum to maximum. The best way to make this adjustment is
with a continuous gray scale pattern on the display. A proper adjustment will give continuous
shading from black to white.
Auto Adjust: All four parameters (clock, Horizontal position, Vertical position, and gain) can be
adjusted automatically by pressing the Horz and DotClk+ button simultaneously. The LC1200R will
sense the incoming video and optimize its settings. For best results, display a pattern containing
white and black with some white pixels along all four edges while the auto adjust is performed.
6.2 User Adjustments
There are features that allow the user to adjust the properties of the LC1200R. These adjustments
will require access to the video board PCB and the inverter. Access to the Photodiode Connector
Section 2.5.3 and Dimming Control Connector Section 2.5.4 can be gained by removing 1 screw and a
small access panel. See Figure 6. ESD precautions should be taken when removing this panel or the
back cover of the unit.
Figure 6:
Remove Screw and
Door
6.2.1 Flip and Mirror
The unit has the capability to flip and/or mirror the video image. This can be done to allow
for the power and video connector to be located on the other side of the unit for flexibility in
mounting the LC1200R. Jumpers are located on the LCD Video Controller Board. See Figure
7 for jumper locations. Note the viewing angle in asymmetric. Rotating the display 180° will
affect the apparent view angle. See Section 7 for view angle.
LC1200R User’s Guide 021-0183-00 Rev A
18 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6.2.2 Max Bright Jumper
The photodiode board can be removed from the system. When the photodiode board is
unplugged the LC1200R will default to the minimum brightness mode. If the user would
like to display to run at maximum brightness, the MAX BRIGHT, JP1, jumper must be inserted
on the inverter board. See Figure 8
Figure 7
Install jumper to flip
Install jumper to
Mirror
Figure 8
Insert Jumper for
Max Brightness
LC1200R User’s Guide 021-0183-00 Rev A
19 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
6.3 Dimming
6.3.1 Photodiode Board and Automatic Dimming Connector
The photodiode board must be mounted in the user’s system so that the photodiode is
exposed to the ambient light. In bright conditions, the LC1200R will adjust to maximum
brightness. In dark conditions, the LC1200R will adjust to approximately 25% of the
maximum luminance. Connector Pin Assignments are in Table 8
Table 8
Pin
1
2
Description
Output from photodiode anode
5V input from the LC12F for
photodiode cathode
3
No connection
6.3.2 Dimming Control Connector Pin Assignment and Performance
A separate connector will allow dimming via an analog input and will allow the inverter to be
inhibited. A 5V reference and ground are provided for cases where an external potentiometer is used
to generate the DIM input. If used, a 50k potentiometer is recommended.
Any connection made to the DIM input will override the Automatic dimming function, thus leave the
DIM input open if using the photodiode for automatic dimming.
Connector mates with Molex 5264 and 42219 series.
Connector Pin Assignments:
Table 9
Pin
1
Name
5V REF
Description
5V source for upper leg of potentiometer, if use; current
limited with 2.2k series resistance
2
DIM
0-5V input to facilitate manual dimming; leave open if not
used. Connect to wiper of pot if used.
Ground for lower leg of potentiometer, if used
No connection
3
4
5
GND
NC
DISABLE Low (<0.5V) will turn off the backlight, High (>2V) will have no
effect on Monitor brightness
6.3.3 Automatic Brightness Mode
For Automatic Brightness Mode, install the photodiode board so that the ambient light conditions
are monitored and leave the DIM pin on the Dimming Control connector open.
LC1200R User’s Guide 021-0183-00 Rev A
20 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
The typical monitor brightness vs. ambient is as follows:
Figure 9. Monitor Brightness vs. Ambient
1600
1400
1200
1000
800
600
400
200
0
0
100
200
300
400
500
600
700
800
900
1000
Ambient, lux
6.3.4 Manual Brightness Mode
For manual brightness mode, apply a 0-5V input voltage to the DIM pin on the dimming
control connector. The DIM input will override any input from the photodiode board. Note
that the photodiode board may be left disconnected if not used.
The LC1200R brightness vs. DIM voltage relationship is Figure 10. 1.5V will dim the LC1200R
to below 100 nits; and above 3.5V will produce maximum brightness.
Note: At extremely low brightness levels, non uniformity and flickering may become evident.
LC1200R User’s Guide 021-0183-00 Rev A
21 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 10
1600
1400
1200
1000
800
600
400
200
0
1
1.5
2
2.5
3
3.5
4
DIM input, volts
6.3.5 Maximum Brightness Mode
If constant maximum brightness is desired, a jumper may be installed at location JP1 on the
inverter board. The jumper will force the LC1200R to maximum brightness unless the
/DISABLE input is active. Use a 0.1 inch jumper such as Molex, part number 15-29-1024.
7 Monitor Performance
7.1 Monitor Luminance
Minimum white-light luminance at the screen center of the Monitor face is 1500 cd/m2 [467 fL,
measured normal to the screen face. Luminance specification applies to the initial luminance, i.e.
prior to additional operation in the end system and after a 10 minute warm up.
Luminancemin > 1,500cd/m2 [467 fL]
7.2 Display Contrast
Display contrast is a relationship between luminance
levels and the ability to perceive a luminance difference.
It is expressed as a ratio of ON white – luminance to OFF
black background luminance generated by:
LC1200R User’s Guide 021-0183-00 Rev A
22 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
ON white-light luminance
C =
OFF black - background luminance
7.3
Display View Angle
110 Hor. -35 . + 55 vert.
CR> 10
Planar LC12 Viewing Angle
Planar LC12 Viewing Angle
400
350
300
250
200
150
100
50
300
250
200
150
100
50
0
0
-80
-60
-40
-20
0
20
40
60
80
-80
-60
-40
-20
0
20
40
60
80
Vertical Viewing Angle (°)
Horizontal Viewing Angle (°)
7.3 Display Uniformity
Luminance Uniformity (UL) measured within 30 mm from edge of the display image area is + 40% of the
luminance measured at the center of the display screen. Edge luminance shall be +/- 60% of center
luminance, normal to the screen face
7.4 Display Chromaticity
The metric used for color coordinate determination is the CIE 1976 UCS (Uniform Chromaticity Scale) u’, v’
system.
Color determination is performed normal to the display in a dark room environment with ambient light
conditions less than 10 lux [1fC] incident illumination.
The measured u’, v’ color coordinates at room temperature for white-light and the red, green, and blue
primaries are listed as typical values.
Table 10
Color
Red
Blue
Green
White
u•
v•
0.517
0.299
0.559
0.489
Perceived Color
0.449
0.144
0.142
0.215
Red
Blue
Yellowish-Green
Warm White
LC1200R User’s Guide 021-0183-00 Rev A
23 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
White color is concentrated around 5600ºK color temperature.
8 Display Cosmetics
The external visual inspection shall be conducted with the unaided eye at a minimum of 35 cm [14in]
from the display surface. There are acceptable defects when the display is in the black mode and in
the white mode.
8.1 Black Display Picture Mode
Power up the Monitor. Display an all black screen via the video input.
•
•
The LCD Panel is acceptable if there are 4 or less green, red, and blue dots visible from 35cm
[14in] with the unaided eye.
The LCD Panel is acceptable if no more than 5 dots are joined.
8.2 White Display Picture Mode
Power up the Monitor. Display an all white screen via the video input.
•
•
The LCD panel is acceptable if there are 4 or less black dots visible from 35c [14in] with the
unaided eye.
The LCD panel is acceptable if no more than 3 dots are joined.
9 Regulatory Agency Requirements
9.1 Safety Certification
The LC1200R does not inhibit customer from certifying product to the following safety standards:
•
•
UL 1950/CAN/CSA C22.2 No. 950-95 Safety of Information Technology, including electrical
business equipment
EN 60950 Safety of Information Technology, including electrical business equipment.
9.2 CE Marking
(Declaration according to ISO/IEC Guide 22 and EN45014)
The LC1200R does not inhibit customer from conforming to the following EC Directives:
Council Directive 73/23/EEC and 93/68/EEC (latest amendment) on the harmonization of the laws of
the Member States relating to electrical equipment designed for use within certain voltage limits is
based on compliance with the following harmonized standards:
•
•
EN 60950 June 2000
EN 41003:1991
LC1200R User’s Guide 021-0183-00 Rev A
24 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Council Directive 89/336/EEC, 92/31/EEC and 93/68/EEC (Latest Amendment) on the approximation
of the laws of the Member States relating to electromagnetic compatibility is based on compliance
with the following harmonized standards:
•
•
Electromagnetic Emissions EN 55022 Class A: 1994
Electromagnetic Immunity EN 50082 part 1:1992
9.3 RFI Emission Certification
The LC1200R is certified to the following emissions standards when installed in customer product
configuration:
•
•
FCC, part 15, paragraph 15.107(b) and 15.109(b), Class A RFI emissions standard.
EN 55022 Class A: 1994 • Limits and measurements of radio interference characteristics of
information technology equipment.
•
•
IEC 1000 3-•2/1995; EN 61000-•3-•2 Current Harmonic Tests
IEC 1000 3-•3/1995; EN 61000-•3-•3 Voltage Fluctuation and Flicker Test
9.4 System Transient Disturbance Requirements
The LC1200R meets the following system transient disturbance requirements:
9.4.1 Electrostatic Discharge
The LC1200R performs normally when subjected to static electricity discharges from persons
touching the external surfaces of the LC1200R. Performance is verified by testing according
to EN 50082-1 (Ref IEC 801-2:1984) at severity level 3 (4 Kv contact discharge, 8 Kv air
discharge).
9.4.2 Electromagnetic Energy Susceptibility Requirements
The LC1200R performs normally in an electromagnetic field with a strength of 10-volts per
meter from 10 KHz to 1 GHz. (REF CISPR 22).
9.5 Labeling
Where applicable, the LC1200R complies with IEC 60417 – Graphical Symbols for Use on Equipment
LC1200R User’s Guide 021-0183-00 Rev A
25 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 11 Sample of Product labeling
9.6 ROHS Compliance
This product will be compliant by June 30, 2006
10 Reliability
10.1 Design Workload
The LC1200R is capable of operating 24 hours a day, 365 days a year under the specified
environmental conditions per Section 3
10.2 MTBF
The MTBF (mean time between failures) value excludes the fluorescent backlight assembly
The LC1200R MTBF is > TBD hours.
11 Description of Warranty
Seller warrants that the Goods will conform to published specifications and be free from defects in
material for 12 months from delivery. To the extent that Goods incorporate third-party-owned
software, Seller shall pass on Seller's licensor's warranty to Buyer subject to the terms and conditions
of Seller's license.
Warranty repairs shall be warranted for the remainder of the original warranty period. Buyer shall
report defect claims in writing to Seller immediately upon discovery, and in any event, within the
warranty period. Buyer must return Goods to Seller within 30 days of Seller’s receipt of a warranty
LC1200R User’s Guide 021-0183-00 Rev A
26 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
claim notice and only after receiving Seller’s Return Goods Authorization. Seller shall, at its sole
option, repair or replace the Goods.
If Goods were repaired, altered or modified by persons other than Seller, this warranty is void.
Conditions resulting from normal wear and tear and Buyer's failure to properly store, install, operate,
handle or maintain the Goods are not within this warranty. Repair or replacement of Goods is Seller’s
sole obligation and Buyer's exclusive remedy for all claims of defects. If that remedy is adjudicated
insufficient, Seller shall refund Buyer's paid price for the Goods and have no other liability to Buyer.
All warranty repairs must be performed at Seller’s authorized service center using parts approved by
Seller. Buyer shall pay costs of sending Goods to Seller on a warranty claim and Seller shall pay costs
of returning Goods to Buyer. The turnaround time on repairs will usually be 30 working days or less.
Seller accepts no added liability for additional days for repair or replacement.
If Seller offers technical support relating to the Goods, such support shall neither modify the warranty
nor create an obligation of Seller. Buyer is not relying on Seller’s skill or judgment to select Goods for
Buyer’s purposes. Seller’s software, if included with Goods, is sold as is, and this warranty is
inapplicable to such software.
SELLER DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO,
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
12 Support and Service
Planar is a US company based in Beaverton, Oregon and Espoo, Finland with a worldwide sales
distribution network. Full application engineering support and service are available to make the
integration of Planar displays as simple and quick as possible for our customers.
Returned Material Authorization (RMA) Procedure: For a RMA number, please contact Planar
Systems, Inc., with the serial number(s) and original purchase order number(s). When returning
goods for repair, please include a brief description of the problem, and mark the outside of the
shipping container with the RMA number.
Planar Systems, Inc.
Customer Service
503.748.1462
Americas Support
1195 NW Compton Drive
Beaverton, OR 97006-1992
Tel: 1-866-PLANAR1 (866) 752-6271
Hours: M-F, 5am - 5pm Pacific Time
Europe and Asia-Pacific Support
Olarinluoma 9 P.O. Box 46
FIN-02201 Espoo, Finland
Tel: +358-9-420-01
LC1200R User’s Guide 021-0183-00 Rev A
27 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Hours: M-F, 7:00am - 4pm CET
13 Glossary of Terms
Aspect Ratio: The ratio of width to height of a display surface. The standard television aspect ratio is 4:3.
Back Porch: The portion of a composite display signal which lies between the trailing edges of a horizontal sync
pulse and the corresponding blanking pulse.
Black Level: The display-signal level corresponding to a specified limit for black peaks.
Blanking: The process of decreasing (or increasing) the display-signal level so that no visible retrace will appear
on the display screen.
Blanking Level: The level of a composite display signal which separates the range containing display information
from the range containing synchronizing information. Also called the pedestal level, or blacker-than-black.
Brightness: A psycho-physiological attribute of visual perception in which a source appears to emit or reflect
more or less light. Its psycho-physical, photometric equivalence is luminance.
Candela-per-meter-squared [cd/m2]: The international unit of luminance (same as nits).
Chrominance: The colorimetric difference (dominant wavelength and purity) between any color and a reference
"white" of equal luminance. In three-dimensional CIE color space, chrominance is a vector which lies in a plane of
constant luminance.
Chromaticity: The color quality of light which is defined by its dominant wavelength and purity (see
Chrominance).
Chromaticity Value: The scalar value of any one component of a three-component color (also called a tristimulus
value). The unit value of each component is the amount of that component added to the other two components
to produce a reference "white".
Color Saturation: A psycho-physiological measurement of the degree to which a color appears to be free of
white light.
Color Temperature: The temperature to which a black body must be heated to produce a color matching that of
the source.
Contrast: The ratio between the maximum and minimum luminance values of a display.
dB (Decibel): A measure of the ratio of two signals. The dB value is 20 x log10 of a voltage or current ratio or 10 x
log10 of a power ratio.
Foot-Candle [fC]: A unit of illumination equal to the illumination which occurs when uniformly distributed
luminous flux is impinging on an area at a rate of one lumen per square foot.
Foot-Lambert [fL]: A unit of luminance equal to the uniform luminance of a perfectly diffusing surface emitting
or reflecting luminance flux at the rate of one lumen per square foot.
Front Porch: The portion of a composite display signal which lies between the leading edges of a horizontal
blanking pulse and the corresponding sync pulse.
Gray Scale: Variations in the luminance value of "white" light, from black to white. Shades of gray are defined as
gray-scale graduations that differ by the square root of 2.
Illuminance: The density of luminance flux impinging on a surface. It is the quotient of the flux divided by the
"apparent" or projected area of the surface.
Image: A displayed view of one or more objects or parts of objects.
Lambert: A unit of luminance equal to the uniform luminance of a perfectly diffusing surface emitting or
reflecting light at the rate of one lumen per square centimeter.
LC1200R User’s Guide 021-0183-00 Rev A
28 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Luminance: Luminous intensity reflected or emitted by a surface in a given direction per unit of apparent area.
Measured in nits.
Lumen: The unit of luminous flux or rate of luminous energy flow. It is equal to the flux radiating through a unit
solid angle (steradian) from a uniform point source of one candela.
Luminous Flux: The time rate of luminous energy flow, measured by its capacity to evoke a visual sensation. It is
expressed in lumens.
Luminous Intensity: The luminous flux radiated by a point source. It is expressed in candela.
LUX: The international unit of illumination. One LUX equals one lumen per square meter.
MTBCF: Mean Time Between Critical Failure
Photometer: Any optical device which uses a comparison technique to measure luminous intensity, luminance,
or illumination. An equality-of-brightness photometer is based on simultaneous comparison of adjoining visual
areas; a flicker photometer compares successive stimuli in the same visual area.
Resolution: The number of addressable, controllable display or picture elements, or the number of hypothetical
coordinate locations which can be used to position graphic elements on a display surface.
Shades of Gray: A division of the gray scale from black to white into a series of discrete luminance shades with a
square-root-of-2 difference between successive shades.
SVGA- Super Video Graphics Adapter
Sync: A contraction of synchronous or synchronization.
VESA: Video Electronics Standards Association
VGA: Video Graphics Adapter
White: The common usage word for high-luminance achromatic colors.
XGA: Extended Graphics Adapter
LC1200R User’s Guide 021-0183-00 Rev A
29 of 29
Download from Www.Somanuals.com. All Manuals Search And Download.
|