Planar PS-Series RS232 protocol
(Applies to PS4200, PS4200TL, PS4250, PS4650, PS5550, PS5551, PS6500 models only)
Table of contents
1 Introduction ...............................................................................................................2
2 Description.................................................................................................................2
2.1 Hardware specification.......................................................................................2
2.2 Communication Setting ......................................................................................2
2.3 Command Message Reference ...........................................................................2
3 Protocol 1 : with ID ...................................................................................................3
3.1 Command Description........................................................................................3
3.2 Set-Function Listing ...........................................................................................3
3.3 Get-Function Listing...........................................................................................8
4 Protocol 2 : without ID............................................................................................16
4.1 Set function listing............................................................................................16
4.2 Remote Control Pass-through mode.................................................................20
________________________________________________________________
V1.0
1 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
1. If the message is receives correctly it will send “+” (02Bh) followed by “CR” (00Dh)
2. If the message is receives incorrectly it will send “-” (02Dh) followed by “CR” (00Dh)
Protocol 1: with ID
3
3.1 Command Description
Length:
TV ID
Total Byte of Message excluding “CR”
Identification for each of TV
Command
Type
Identify command type,
“s” (0x73h) : Set Command
“g” (0x67h) : Get Command
“r” (0x72h) : Reply Command
“p” (0x70h) : RCU Pass-through
“+” (0x2Bh) : Valid command Reply
“-“ (0x2Dh) : Invalid command Reply
Function command code: One byte ASCII code
Command:
Value[1~3]: Three bytes ASCII that defines the value
0x0D
CR
3.2
Set-Function Listing
The PC can control the LCD Monitor for specific actions. The Set-Function command allows you to
control the LCD monitor behavior in a remote sit through the RS232 port. The Set-Function packet
format consists of 11 bytes.
Set-Function description:
Length:
TV ID
Total Byte of Message excluding “CR”
Identification for each of TV
If we want to set all TV settings, TV ID can use “99” to achieve, and it
will not have Reply command on this function.
Identify command type,
“s” (0x73h) : Set Command
Function command code: One byte ASCII code
Command
Type
Command:
Value[1~3]: Three bytes ASCII that defines the value
CR 0x0D
Set-Function format
Send: (Command Type=”s”)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
d
1
2
3
Byte 1 Byte
Count
2
Byte
2~3
1 Byte
1 Byte
1 Byte 1 Byte 1 Byte
1
Byte
9
Bytes
order
1
4
5
6
7
8
Reply: (Command Type=”+” or “-”)
Name Lengt
h
ID
Command
Type
CR
1
Byte 1 Byte
2
1 Byte
________________________________________________________________
V1.0
3 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Count
Bytes
order
Byte
2~3
Byte
5
1
4
Example1: Set Brightness as 76 for TV-02 and this command is valid
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
0x73
d
1
2
3
Hex
0x38 0x30
0x32
0x24
0x30
0x37
0x36 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command
Type
CR
Hex
0x34 0x30
0x32
0x2B
0x0
D
Example2: Set Brightness as 176 for TV-02 and this command is NOT valid
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
3
Type
0x73
d
1
2
Hex
0x38 0x30
0x32
0x24
0x31
0x37
0x36 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command
Type
CR
Hex
0x34 0x30
0x32
0x2D
0x0
D
Example3: Set Tint as 32 for TV-03 and this command is valid
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
3
Type
0x73
d
1
2
Hex
0x38 0x30
0x33
0x27
0x30
0x33
0x32 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command
Type
CR
Hex
0x34 0x30
0x33
0x2B
0x0
D
Example4: Set Tint as 75 for TV-03 and this command is NOT valid
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
d
Type
0x73
1
2
3
Hex
0x38 0x30
0x33
0x27
0x30
0x37
0x35 0x0
D
________________________________________________________________
V1.0
4 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Reply (Hex Format)
Name Lengt
h
ID
Command
Type
CR
Hex
0x34 0x30
0x33
0x2D
0x0
D
Example5: Set Brightness as 76 for all TV and this command is valid
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
0x73
d
1
2
3
Hex
0x38 0x39
0x39
0x24
0x30
0x37
0x36 0x0
D
No Reply.
Set-function table
Set Function
Len ID Cmd
Command
Type Code Code (Three ASCII
Value Range
Comments
(ASCII) (Hex)
bytes)
Picture mode
8
s
81
Contrast
Brightness
Color
8
8
8
8
8
8
s
s
s
s
s
s
#
$
23
24
82
83
25
84
Tint
Sharpness
Backlight
%
Step : 20 for OSD
display range 0~5
8
8
s
85
86
DCR
S
Color Temp
8
s
87
Input Resolution
8
s
5
35
Volume
________________________________________________________________
V1.0
5 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
8
8
s
s
6
36
88
Mute
Audio Source
8
s
89
Only effected for
models include
internal speakers.
Speaker
8
8
8
s
s
s
1
31
8A
8B
Aspect Ratio
PIP Enable
Full
PIP Main Input
8
s
8C
PIP Sub Input
8
8
s
s
8D
8E
PIP Size
PIP Position
8
s
“
000 : VGA
Video Source
001 : HDMI1
003 : CVBS1
004 : YPbPr
005 : S-Video
006 : DVI
8
s
Auto adjustment
________________________________________________________________
V1.0
6 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
8
8
8
8
8
s
s
s
s
s
000 ~ 32
000 ~ 32
000 ~ 100
000 ~ 100
000: OFF
Clock frequency
Phase
H.Position
V.Position
Ambient Light
Sensor
001: ON
000: OFF
001: ON
000: OFF
8
8
s
s
Blue Screen
Auto Detect
001: ON
8
8
s
s
000: OFF
Only effected for
Touch models.
Touch Feature
Language
001: On
2
000: English
001: French
002: Spanish
003: Czech
Optional by
different models.
Optional by
different models.
004: Danish
8
s
000: OFF
001: ON
Over Scan
8
8
8
8
8
8
s
s
s
s
s
s
000 ~ 099
000 ~ 012
000 ~ 031
000 ~ 023
000 ~ 059
000: OFF
From 2000~2099
RTC Year
RTC Month
RTC Day
RTC Hour
RTC Minute
Daylight saving
time
001: ON
8
8
8
8
8
s
s
s
s
s
001 ~ 010
001 ~ 010
001 ~ 010
001 ~ 010
000: OFF
001: ON
H Monitor
V Monitor
H Position
V Position
Frame Comp.
8
s
000: OFF
001: Eco
Power save
________________________________________________________________
V1.0
7 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
002: VGA Only
003: Standard
8
8
s
s
3D 001 ~ 098
Monitor ID
47 000: OFF
001: ON
Image retention
8
8
s
s
AA 000: OFF
001: ON
Auto adjustment
DDC/CI
AB 000: OFF
001: ON
8
8
s
s
AC
Reset User Default
OSD Info Box
5B 000: OFF
001: ON
8
8
8
s
s
AD
Store User Default
Factory Reset
Power
7E
!
21
000: STBY
001: ON
8
s
A
41
000 : POWER
001 : SOURCE
002 : MENU
003 : UP
Key Pad
004 : DOWN
005 : LEFT
006 : RIGHT
007 : MUTE
000: Disable
001: Enable
s
B
42
Remote Control
002: Pass
through
8
8
8
s
s
s
C
E
F
43
45
46
000: Disable
001: Enable
000: Disable
001: Enable
000: Disable
001: Enable
Key Pad function
Menu Key function
Power Key
function
3.3 Get-Function Listing
The PC can interrogate the LCD Monitor for specific information. The Get-Function packet format
consists of 5 bytes which is similar to the Set-Function packet structure. Note that the “Value” byte is
always = 00.
________________________________________________________________
Document 020-1156-00 Rev B
V1.0
8 / 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Get-Function description:
Length:
TV ID
Total Byte of Message excluding “CR”
Identification for each of TV
Command
Type
Command:
Identify command type,
“g” (0x67h) : Get Command
Function command code: One byte ASCII code
Value[1~3]: Three bytes ASCII that defines the value
NOTE: to get backlight senor, thermal sensor, and ambient sensor
need four bytes ASCII that defines the value and the length is 9.
0x0D
CR
Get-Function format
Send: (Command Type=”g”)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
d
1
2
3
Byte 1 Byte
Count
2
Byte
2~3
1 Byte
1 Byte
1 Byte 1 Byte 1 Byte
1
Byte
9
Bytes
order
1
4
5
6
7
8
Reply: (Command Type=”r” or “-”)
If the Command is valid, Command Type =”r”
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
d
1
2
3
Byte 1 Byte
Count
2
Byte
2~3
1 Byte
1 Byte
1 Byte 1 Byte 1 Byte
1
Byte
9
Bytes
order
1
4
5
6
7
8
If the Command is Not valid, Command Type=”-“
Name Lengt
h
ID
Command
Type
CR
Byte 1 Byte
Count
2
Byte
2~3
1 Byte
1
Byte
5
Bytes
order
1
4
Example1: Get Brightness from TV-05 and this command is valid.
The Brightness value is 67.
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
0x67
d
1
2
3
Hex
0x38 0x30
0x35
0x62
0x30
0x30
0x30 0x0
D
Reply(Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
d
1
2
3
________________________________________________________________
V1.0
9 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Hex
0x38 0x30
0x35
0x72
0x62
0x30
0x36
0x37 0x0
D
Example2: Get Brightness from TV-05 , but the Brightness command ID is error
and it is NOT in the command table.
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
0x67
d
1
2
3
Hex
0x38 0x30
0x35
0XD3
0x30
0x30
0x30 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command
Type
CR
Hex
0x34 0x30
0x35
0x2D
0x0
D
Example3: Get Tint from TV-0007 and this command is valid.
The Tint value is 32.
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
0x67
d
1
2
3
Hex
0x38 0x30
0x37
0X65
0x30
0x30
0x30 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
Type
0x72
d
1
2
3
Hex
0x38 0x30
0x37
0x65
0x30
0x33
0x32 0x0
D
Example4: Get Tint from TV-07 , but the Brightness command ID is error and it is NOT in the
command table.
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value CR
2
Type
0x67
d
1
3
Hex
0x38 0x30
0x37
0XD7
0x30
0x30
0x30 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command
Type
CR
Hex
0x34 0x30
0x37
0x2D
0x0
D
Example5 Get backlight sensor from TV-0007 and this command is valid.
The lux value is 1786 (ASCII code).
Send (Hex Format)
________________________________________________________________
Document 020-1156-00 Rev B
V1.0
10 / 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Name Lengt
h
ID
Command Comman Value Value Value Value CR
Type
0x67
d
1
2
3
4
Hex
0x39 0x30
0x37
0X6F
0x30
0x30
0x30
0x30 0x0
D
Reply (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value Value CR
Type
0x72
d
1
2
3
3
Hex
0x39 0x30
0x37
0X6F
0x31
0x37
0x38
0x36 0x0
D
Example6 Get ambient sensor from TV-0007 and this command is valid.
The lux value is 1568 (ASCII code).
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value Value CR
Type
0x67
d
1
2
3
4
Hex
0x39 0x30
0X70
0x30
0x30
0x30
0x30 0x0
D
0x37
Reply (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value Value CR
3
Type
0x72
d
1
2
4
Hex
0x39 0x30
0X70
0x31
0x35
0x36
0x38 0x0
D
0x37
Example7 Get thermal sensor from TV-0007 and this command is valid.
The value is +075 degree (ASCII code). NOTE: positive degree is “+”ASCII code and negative degree
is “-”ASCII code.
Send (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value Value CR
Type
0x67
d
1
2
3
4
Hex
0x39 0x30
0X71
0x30
0x30
0x30
0x30 0x0
D
0x37
Reply (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value Value CR
4
Type
0x72
d
1
2
3
Hex
0x39 0x30
0X71
0x2B 0x30
0x37
0x35 0x0
D
0x37
Example8 Get Running Hours from TV-0007 and this command is valid.
The value is 21,356 hours (ASCII code).
Send (Hex Format)
Name Lengt
ID
Command Comman Value Value Value Value Value CR
________________________________________________________________
V1.0
11 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
h
Type
0x67
d
1
2
3
4
5
Hex
0x3A 0x30
0X76
0x30
0x30
0x30
0x30
0x30 0x0
D
0x37
Reply (Hex Format)
Name Lengt
h
ID
Command Comman Value Value Value Value Value CR
Type
0x72
d
1
2
3
4
5
Hex
0x3A 0x30
0X76
0x32
0x31
0x33
0x35
0x36 0x0
D
0x37
________________________________________________________________
V1.0
12 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
PC Get-function command to LCD Monitor
Get Function
Len ID Cmd
Command
Type Code Code (Three ASCII
Value Range
Comments
(ASCII) (Hex)
bytes)
Picture mode
8
B1
Contrast
Brightness
Color
8
8
8
8
8
8
61
62
B2
B3
63
B4
Tint
Sharpness
Backlight
Step : 20 for OSD
display range 0~5
8
8
B5
B6
DCR
Color Temp
8
B7
Input Resolution
8
8
66
67
Volume
Mute
8
B8
Audio Source
8
B9
Only effected for
models include
internal speakers.
Speaker
________________________________________________________________
V1.0
13 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
8
8
8
77
BA
BB
Aspect Ratio
PIP Enable
Full
PIP Main Input
8
BC
BD
PIP Sub Input
8
8
PIP Size
000 : VGA
001 : HDMI1
003 : CVBS1
004 : YPbPr
005 : S-Video
006 : DVI
Video Source
8
8
8
8
8
000 ~ 32
Clock frequency
Phase
000 ~ 32
000 ~ 100
000 ~ 100
000: OFF
001: ON
H.Position
V.Position
Ambient Light
Sensor
8
8
8
8
000: OFF
001: ON
Blue Screen
Auto Detect
Touch Feature
Language
000: OFF
001: ON
g
000: OFF
001: ON
Only effected for
Touch models.
000: English
001: French
002: Spanish
________________________________________________________________
V1.0
14 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
003: Czech,
004: Danish
Optional by
different models.
Optional by
different models.
8
000: OFF
001: ON
Over Scan
8
8
8
8
8
8
000 ~ 099
000 ~ 012
000 ~ 031
000 ~ 023
000 ~ 059
000: OFF
001: ON
From 2000~2099
RTC Year
RTC Month
RTC Day
RTC Hour
RTC Minute
Daylight saving
time
8
8
8
8
8
001 ~ 010
001 ~ 010
001 ~ 010
001 ~ 010
000: OFF
001: ON
H Monitor
V Monitor
H Position
V Position
Frame Comp.
8
000: OFF
001: Eco
Power save
002: VGA Only
003: Standard
8
8
75 001 ~ 098
Monitor ID
72 000: OFF
001: ON
Image retention
8
8
DA 000: OFF
001: ON
Auto adjustment
DDC/CI
DB 000: OFF
001: ON
16
DC PS5550 p.xx
(ASCII), the return
value will be
different for
FW Version
different model
8
8
5D 000: OFF
001: ON
OSD Info Box
Power
6C
000: STBY
001: ON
________________________________________________________________
V1.0
15 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
68
000: Disable
001: Enable
Lock
Remote Control
002: Pass
through
000: Disable
8
8
8
69
73
74
Lock
Lock
Lock
Key Pad function
Menu Key function
001: Enable
000: Disable
001: Enable
000: Disable
Power Key
function
001: Enable
000~50
8
8
9
9
A
g
g
g
g
g
m
n
p
q
v
6D
6E
70
71
76
5V
12V
000~120
0000 ~ 2000
-055 ~ +125
0 ~ 65535
Ambient Sensor
Thermal Sensor
Operating Time
Hour
4
Protocol 2 : without ID
Set function listing
4.1
The PC can control the LCD Monitor for specific actions. The Set-Function command allows you to
control the LCD monitor behavior in a remote sit through the RS232 port. The Set-Function packet
format consists of 5 bytes. Note that the “Value” byte is always = 00.
Set-Function description:
Length: Total bytes of message = 5 ASCII (35H) excluding “CR”
Command: Function command code: One byte ASCII code
Value[1~3]: Three bytes ASCII that defines the value
Set-Function format:
Name
Byte Count 1 Byte
Bytes order
Length Command Value1 Value2 Value3
CR
1 Byte
2
1 Byte 1 Byte 1 Byte 1 Byte
1
3
4
5
6
All Set-Function from PC to Monitor (ASCII)
Name
Length Command Value1 Value2 Value3 CR
Byte Count
Bytes order
5
1
1 Byte
2
1 Byte 1 Byte 1 Byte 00D
3
4
5
6
Example: Set Mute-ON command (ASCII)
Name
Length Command Value1 Value2 Value3 CR
Byte Count
Bytes order
5
1
6
2
0
3
0
4
0
5
00D
6
________________________________________________________________
V1.0
16 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Example: Set Mute-OFF command (ASCII)
Name
Length Command Value1 Value2 Value3 CR
Byte Count
Bytes order
5
1
6
2
0
3
0
4
1
5
00D
6
LCD Monitor will send “+” (02Bh) and “CR” bytes to PC after receiving a valid command.
LCD Monitor will send “-” (02Dh) and “CR” bytes to PC if the command is not valid.
Value Range: Three bytes ASCII value range
Command Function command code in ASCII
Code:
set command table
Set Function
Len Value Range
Comments
Code (Three ASCII
bytes)
(Hex)
Picture mode
5
81
Contrast
Brightness
Color
5
5
5
5
5
5
23
24
82
83
25
84
Tint
Sharpness
Backlight
Step : 20 for OSD
display range 0~5
5
5
85
86
DCR
Color Temp
5
87
VGA only
Input Resolution
5
35
Volume
________________________________________________________________
V1.0
17 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
5
5
36
88
Mute
Audio Source
5
89
Only effected for
models include
internal speakers.
Speaker
5
5
5
31
8A
8B
Aspect Ratio
PIP Enable
Full
PIP Main Input
5
8C
PIP Sub Input
5
5
8D
8E
PIP Size
PIP Position
5
000 : VGA
Video Source
001 : HDMI1
003 : CVBS1
004 : YPbPr
005 : S-Video
006 : DVI
5
Auto adjustment
________________________________________________________________
V1.0
18 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
5
5
5
5
5
000 ~ 32
Clock frequency
Phase
000 ~ 32
000 ~ 100
000 ~ 100
000: OFF
001: ON
H.Position
V.Position
Ambient Light
Sensor
5
5
5
5
000: OFF
001: ON
Blue Screen
Auto Detect
Touch Feature
Language
000: OFF
001: ON
000: OFF
001: ON
Only effected for
Touch models.
000: English
001: Franch
002: Spanish
003: Czech,
Optional by
different models.
Optional by
different models.
004: Danish
5
000: OFF
001: ON
Over Scan
5
5
5
5
5
5
000 ~ 099
000 ~ 012
000 ~ 031
000 ~ 023
000 ~ 059
000: OFF
001: ON
From 2000~2099
RTC Year
RTC Month
RTC Day
RTC Hour
RTC Minute
Daylight saving
time
5
5
5
5
5
001 ~ 010
001 ~ 010
001 ~ 010
001 ~ 010
000: OFF
001: ON
H Monitor
V Monitor
H Position
V Position
Frame Comp.
5
000: OFF
001: ECO
002: VGA Only
Power save
________________________________________________________________
V1.0
19 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
003: Standard
3D 001 ~ 098
5
5
Monitor ID
Image retention
47 000: OFF
001: ON
5
5
AA 000: OFF
001: ON
Auto adjustment
DDC/CI
AB 000: OFF
001: ON
AC
5
5
Reset User Default
OSD Info Box
5B 000: OFF
001: ON
AD
5
5
5
Store User Default
Factory Reset
Power
7E
21
000: STBY
001: ON
5
41
000 : POWER
001 : SOURCE
002 : MENU
003 : UP
Key Pad
004 : DOWN
005 : LEFT
006 : RIGHT
007 : MUTE
000: Disable
42
Remote Control
001: Enable
002: Pass
through
5
5
5
43
45
46
000: Disable
001: Enable
000: Disable
001: Enable
000: Disable
001: Enable
Key Pad function
Menu Key function
Power Key
function
4.2 Remote Control Pass-through mode
When PC sets the LCD monitor to Remote Control Pass through mode, the LCD shall send a three bytes
packet (followed by “CR”) in response to RCU button activation. Note, that in this mode the RCU shall
have no effect on the monitor function. For example: “+Volume” will not change the volume in the
LCD but only sends “+Volume” code to PC over the RS232 port.
Remote Control pass-through packet format from LCD monitor to PC(ASCII)
Name
Length RCU-Code1 RCU-Code2
CR
00D
4
Byte Count
Bytes order
3
1
MSB
2
LSB
3
Example: Remote Control pass-through when “Menu” key is pressed (2E)
Name
Length RCU-Code1 RCU-Code2
CR
Byte Count
3
2
E
00D
________________________________________________________________
V1.0
20 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
Bytes order
1
2
3
4
Example: Remote Control pass-through when key “DOWN” is pressed (21)
Name
Length RCU-Code1 RCU-Code2
CR
00D
4
Byte Count
Bytes order
3
1
2
2
1
3
Example: Remote Control pass-through when “Power” key is pressed (0C)
Name
Length RCU-Code1 RCU-Code2
CR
00D
4
Byte Count
Bytes order
3
1
0
2
C
3
RCU Key
Support
CODE (HEX)
Notes
Y
PWR
Exit
0C
0F
10
11
20
21
0D
0A
2E
12
28
4B
39
38
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
= MENU key
Vol +
Vol -
UP
DOWN
Mute
Enter
= SOURCE key
= SOURCE key
Menu
Information
Input
DVI
VGA
HDMI
AV
37
70
Y
YPbPr
________________________________________________________________
V1.0
21 / 21
Document 020-1156-00 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
|