Pioneer Speaker S LX70W User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.  
[Not applicable to the Taiwanese model]  
Replacement and mounting of an AC plug on the power supply cord of this unit should be performed only by qualified  
service personnel.  
IMPORTANT: THE MOULDED PLUG  
This appliance is supplied with a moulded three pin mains plug for your safety and convenience. A 10 amp fuse is fitted in this plug. Should  
the fuse need to be replaced, please ensure that the replacement fuse has a rating of 10 amps and that it is approved by ASTA or BSI to  
BS1362.  
Check for the ASTA mark  
or the BSI mark  
on the body of the fuse.  
If the plug contains a removable fuse cover, you must ensure that it is refitted when the fuse is replaced. If you lose the fuse cover the plug  
must not be used until a replacement cover is obtained. A replacement fuse cover can be obtained from your local dealer.  
If the fitted moulded plug is unsuitable for your socket outlet, then the fuse shall be removed and the plug cut off and disposed of  
safely. There is a danger of severe electrical shock if the cut off plug is inserted into any 13 amp socket.  
If a new plug is to be fitted, please observe the wiring code as shown below. If in any doubt, please consult a qualified electrician.  
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:  
Blue : Neutral Brown : Live  
As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in  
your plug, proceed as follows ;  
The wire which is coloured BLUE must be connected to the terminal which is marked with the  
letter N or coloured BLACK.  
The wire which is coloured BROWN must be connected to the terminal which is marked with the  
letter L or coloured RED.  
How to replace the fuse: Open the fuse compartment with a screwdriver and replace the fuse.  
D3-4-2-1-2-2_B_En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
ACCESSORY ITEMS............................4  
FEATURES ..........................................4  
IN COMBINATION WITH  
FEATURES  
300 W (RMS) power with D class amplifier that serves  
audio and video software playback such as Dolby*  
Digital with a wide dynamic range.  
Equipped with 30 cm driver  
Crossover frequency can be set to 50 Hz, 60 Hz, 70 Hz,  
80 Hz, 100 Hz, 120 Hz, 160 Hz, 200 Hz.  
Equipped with Bass Mode selector (Music/Cinema  
mode).  
SPEAKERS ..........................................4  
INSTALLATION...................................5  
Speaker Installation............................5  
Installation Precautions .....................5  
PANEL FACILITIES..............................6  
FRONT PANEL.....................................6  
REAR PANEL.......................................6  
CONNECTIONS...................................7  
LINE LEVEL CONNECTION.................7  
OPERATION .......................................7  
TROUBLESHOOTING .........................8  
SPECIFICATIONS ................................8  
*
Maunfactured under license from Dolby Laboratories.  
“Dolby” and the double-D symbol are trademarks of Dolby  
Laboratories.  
IN COMBINATION WITH  
SPEAKERS  
The frequency characteristics of the S-LX70W combined  
with small-size speakers are shown below. As shown in  
these figures, the low frequency range is improved.  
• These special characteristics are obtained in an  
echoless chamber. The effect of an additional S-LX70W  
in an ordinary listening room is better than the chart  
indicates when positioned adequately.  
ACCESSORY ITEMS  
Small-size speakers + S-LX70W  
RCA plug cord x 1  
Power cable x 1  
Small-size speaker  
FREQUENCY (Hz)  
Polishing cloth x 1  
Warranty card x 1  
Operating instructions  
• With playback of Dolby* Digital, establishment of a  
special channel for the subwoofer is recommended;  
and with playback of LFE (Low Frequency Effect: sound  
effect like the rumbling of the earth, whose purpose is  
to intensify the force of the video), the S-LX70W is  
especially effective.  
Dolby* Digital  
Dolby Digital is the name of the Dolby Surround multi-  
channel digital system that was developed from Dolby  
Surround, as a continuation of Dolby Pro Logic Surround.  
Dolby Digital is also referred to as a 5.1 channel system.  
This is because it has 5 channels in the 20 Hz to 20 kHz  
frequency range (front left and right, center, and rear left  
and right) and an independent channel for the  
subwoofer. The subwoofer channel is also referred to as  
LFE (Low Frequency Effect).  
The LFE channel is used according to individual tastes to  
enhance the bass effect.  
4
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTES:  
• To avoid interference with the picture on a nearby TV  
set, use magnetically shielded speaker systems. This  
is particularly important for the center speaker since it  
is usually located closest to the TV.  
INSTALLATION  
Speaker Installation  
• Position the left and right channel speakers at equal  
distances from the TV set and approximately 1.8 meters  
from each other.  
• Install the center speaker above or below the TV so that  
the sound of the center channel is localized at the TV  
screen.  
• Subwoofer Installation Criteria  
1 Left speaker  
2 Right speaker  
3 Recommended installation range for the  
subwoofer  
4 Listening position  
• The rear (surround) speakers are most effective when  
installed in parallel locations directly to the side, or  
slightly behind, the listener, at a level about 1 meter  
above the listener’s ears.  
1
2
CAUTION:  
When installing the center speaker on top of the TV,  
be sure to secure it with tape or some other suitable  
means.  
Otherwise, the speaker may fall from the TV due to  
external shocks such as earthquakes, and it may lead  
to endangering those nearby or damaging the  
speaker.  
3
4
Installation Precautions  
• Install the unit in a well-ventilated location where it will  
not be exposed to high temperatures and high  
humidity.  
The subwoofer plays back the bass in monaural, making  
use of the fact that the human ear is not very sensitive to  
the direction of low-pitched sound. Because of this, the  
subwoofer can be installed almost anywhere. If it is  
installed too far away, however, the sound from the other  
speakers may become unnatural.  
• Do not place the unit near stoves or other heating  
equipment or at locations exposed to direct sunlight,  
as these can have an adverse effect on the cabinet and  
internal components. Also, do not install the unit  
where there is too much dust or high humidity, as  
these can cause malfunctioning or breakdowns.  
(Avoid cooking tables and other locations where the  
unit would be exposed to heat, steam and soot.)  
• Do not place heavy or large objects on top of the  
speaker. Doing so could provoke the speaker to fall,  
causing damages or bodily injury. If speakers fall from  
their installation locations, they may suffer irreparable  
cracks in their finish.  
• An example of speaker positioning  
1 Front left speaker  
2 Center speaker  
3 Front right speaker  
4 Subwoofer  
5 Listening area  
6 Rear left speaker  
7 Rear right speaker  
• Keep the unit away from devices such as cassette  
decks which are sensitive to magnetic fields.  
This speaker system is magnetically shielded.  
However, depending on the installation location,  
color distortion may occur if the speaker system is  
installed extremely close to the screen of a television  
set.  
2
1
3
If this happens, turn off the power switch of the  
television set, and turn it on after 15 to 30 minutes.  
If the problem persists, place the speaker system  
away from the television set.  
4
• Do not place the speaker on an unstable surface, as  
doing so may cause the speaker to fall and cause  
damage or bodily injury.  
5
• Do not place cups, glasses, or other containers with  
fluids on top of the units, since the units may be  
damaged if the liquid spills.  
6
7
5
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
• The installation location selected should have a sturdy  
floor surface. Mounting the speaker on a long-pile  
carpet should be avoided, since the carpet may touch  
the driver’s diaphram, causing distorted sound.  
• Please install this unit away from the antenna cable of  
the tuner, as noise can be caused with installation  
close to the antenna cable. In such a case, use this  
unit at a position away from the antenna and the  
antenna cable, or when playback of extra bass is not  
required, switch off the power for this unit.  
1 Power Indicator (STANDBY/ON)  
Lights blue when the power has been switched ON.  
When AUTO STANDBY switch is set to ON, lights blue  
whenever the speaker receive an audio signal. If the  
power is switched OFF only briefly, the indicator lights  
blue when power is restored. If no signal is present for  
more than 12 minutes, the subwoofer automatically  
reverts to standby mode and the power indicator lights  
red. If, subsequently, a signal is received, power  
automatically comes back on and the power indicator  
lights blue.  
MAINTENANCE OF EXTERNAL SURFACES  
• Clean the surface by wiping with the provided  
polishing cloth, or with another soft, dry cloth.  
• When the surfaces are very dirty, wipe with a soft  
cloth dipped in some neutral cleanser diluted five  
or six times with water, and wrung out well, and  
then wipe again with a dry cloth. Do not use  
furniture wax or cleaners.  
NOTE:  
• If you are planning on switching the unit OFF for a long  
period of time, make sure to check that the indicator  
light has gone out after switching OFF.  
2 Power switch (POWER)  
When pressed, power is turned ON; when pressed  
again, power is turned OFF.  
• Never use thinners, benzine, insecticide sprays  
and other chemicals on or near this unit, since  
these will corrode the surfaces.  
3 Volume knob (VOLUME)  
Sets the subwoofer volume.  
• Turn the knob slowly from the MIN position.  
• With this unit, the bass level can be independently  
set, so do not turn up the bass on the AV amplifier.  
PANEL FACILITIES  
FRONT PANEL  
4 Crossover knob (CROSSOVER)  
When using the subwoofer, set the upper frequency  
limit for the subwoofer (50 Hz, 60 Hz, 70 Hz, 80 Hz,  
100 Hz, 120 Hz, 160 Hz, 200 Hz) so that it  
complemets the output from your other speakers.  
When using the bass managment features of an AV  
receiver, set to BYPASS ON in order to use the low-  
pass filter of the AV receiver for high quality sound.  
5 Bypass switch (BYPASS)  
When set to ON, the audio signal is routed directly to  
the woofer unit, bypassing the amplifier’s filter.  
POWER  
STANDBY/ON  
1
6 Bass mode switch (BASS MODE)  
MUSIC: The characteristic frequencies become flat.  
Recommended for music sources.  
CINEMA: Low frequencies are emphasized.  
Recommended for sources that require strong bass.  
2
7 Phase switch (PHASE 0º /180º)  
REAR PANEL  
When set to 180º , the output phase becomes the  
reverse of the input signal, and when set to , it is in  
the same phase as the input signal.  
• Normally, the switch is set to .  
But when the sound connection between the  
subwoofer and the left and right speakers sounds  
unnatural, try switching to 180º and set the switch  
in the position where the sound is natural.  
• When using two or more subwoofers together,  
make sure that the phase switch of all of them are  
set to the same position.  
3
MIN  
MAX  
VOLUME  
80Hz  
100Hz  
70Hz  
120Hz  
60Hz  
160Hz  
200Hz  
50Hz  
4
CROSSOVER  
BYPASS  
ON  
OFF  
5
6
7
8
INEMA  
USIC  
BASS MODE  
0∞  
180∞  
PHASE  
ON  
OFF  
AUTO STANDBY  
LINE LEVEL  
OUTPUT INPUT  
AC IN  
6
En  
9
11  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8 Auto Standby switch (AUTO STANDBY)  
Switches the Auto Standby feature on/off.  
When switched ON (the default setting is OFF), the  
Auto Standby feature becomes active. In this mode, if  
there is no input signal for 12 minutes the system  
automatically switches to standby. The power is  
automatically switched on again if an input signal is  
detected.  
10 Line Level Input terminal (LINE LEVEL INPUT)  
Connect to the SUBWOOFER PREOUT terminal of an  
amplifier or receiver, with the specially provided RCA  
plug cord.  
11 AC INLET  
• Connect the power cord to the powered subwoofer  
unit’s AC INLET.  
• Connect the power cord to a AC socket.  
NOTE:  
• There may be cases where a connected component  
outputs noise or some other non-audio signal which  
causes this system to automatically power on when in  
Auto Standby mode. If this happens, switch off the  
Auto Standby mode and switch the system on/off  
manually.  
S-LX70W Music mode Frequency response  
100  
Bypass  
90  
80  
70  
9 Line Level Output terminal (LINE LEVEL OUTPUT)  
Used for connecting other equipment through the  
amplifier. The signal output from this jack is not  
affected in any way by the settings of the various  
controls on the unit.  
60  
Non-bypass  
(Crossover 200 Hz)  
50  
40  
10  
100  
1000  
10000  
Frequency (Hz)  
CONNECTIONS  
Before making or changing any connections, switch off the power and disconnect both this unit and the  
amplifier/receiver from the AC outlet.  
LINE LEVEL CONNECTION  
S-LX70W (Rear Panel)  
Supplied RCA plug cord  
This connection is for an amplifier or receiver equipped  
with a SUBWOOFER PREOUT terminal. Connect to the  
LINE LEVEL INPUT terminal on this unit, using the  
specially provided RCA plug cord.  
NOTE:  
• When connected to the PREOUT terminal for  
surround center channel on the amplifier or receiver,  
the bass is heard only on the center channel, so it will  
be insufficient.  
OPERATION  
For details regarding operating part functions, refer to  
page 6.  
2. Operate the amplifier or receiver and adjust the  
volume of the other speakers.  
1. Turn the POWER switch (2) ON.  
3. Adjust the volume of the bass with the VOLUME  
knob (3).  
• When necessary, operate the CROSSOVER knob (4)  
and PHASE switch (7), and then adjust with the  
VOLUME knob (3). Set the BASS MODE switch (6) to  
either MUSIC or CINEMA.  
• If the unit’s power cord is connected to a switched AC  
outlet on the amplifier or receiver and the switch is left  
ON, the unit can be turned ON/OFF together with the  
amplifier or receiver.  
• If the unit cannot be connected to the amplifier or  
receiver, turn the power to the amplifier or receiver ON  
before turning the power to the unit ON. When turning  
the power OFF, turn the power to the unit OFF before  
turning the power to the amplifier or receiver OFF.  
4. Turn the POWER switch (2) OFF.  
• The power indicator disappears.  
7
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TROUBLESHOOTING  
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with  
this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other  
components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks  
listed below, ask your nearest PIONEER authorized service center or your dealer to carry out repair work.  
SYMPTOM  
CAUSE  
REMEDY  
• Insert plug securely.  
1
2
3
No power is being supplied  
(Indicator does not light up  
when power switch is turned  
on.)  
• Power supply plug is not  
correctly inserted.  
No sound  
(Indicator is lit.)  
• Connection of accessory RCA  
plug cord is wrong or  
• Check again and connect correctly.  
• Turn clockwise slowly.  
disconnected.  
VOLUME knob is set to MIN.  
Sound is distorted.  
• Level is too high.  
• Turn the VOLUME knob counter-  
clockwise to lower the level.  
• Input level is too high.  
• Turn the amplifier’s output level (volume,  
bass control, bass boost) counter-  
clockwise to lower the level.  
4
5
Howling noise occurs.  
• No power supplied to the  
amplifier.  
• Subwoofer level is set too high.  
• Connect an amplifier and supply power.  
• Place the subwoofer a good distance  
from speakers. Turn the VOLUME knob  
counter-clockwise to lower the volume.  
Much noise when listening to  
AM or FM broadcasts.  
• The AM loop antenna or the FM • Increase the distance between the AM or  
indoor antenna is close to this  
unit.  
FM antenna (for indoor use) and this unit.  
SPECIFICATIONS  
Cabinet ....................... Floor type with CLOSED BOX system  
(magnetically shielded)  
Accessories............................................... RCA plug cord x 1  
Power cable x 1  
Speaker........................................................... 30 cm cone type  
Frequency response  
....................................25 Hz to 4000 Hz (set to BYPASS ON)  
Power Amplifier Continuous Power Output (RMS)  
................................................................... 300 W/4 (100 Hz)  
Input (sensitivity at 100 Hz/impedance)  
Polishing cloth x 1  
Warranty card x 1  
Operating instructions  
Specifications and design subject to possible  
modification without notice, due to improvements.  
LINE LEVEL (RCA jack)................................... 160 mV/33 kΩ  
Output (Level at 100 Hz/impedance)  
LINE LEVEL (RCA jack)...................................... 160 mV/1 kΩ  
Selectable CROSSOVER Frequencies  
.......................................................50 Hz, 60 Hz, 70 Hz, 80 Hz,  
100 Hz, 120 Hz, 160 Hz, 200 Hz  
Published by Pioneer Corporation.  
Copyright © 2007 Pioneer Corporation.  
All rights reserved.  
Outline Dimension  
........................... 362 mm (W) x 365 mm (H) x 362 mm (D)  
Weight (without package).............................................18.2 kg  
Power Requirements  
Taiwanese model................................. 110 V~, 50 Hz/60 Hz  
All other models.....................220 V to 240 V~, 50 Hz/60 Hz  
Power Consumption......................................................... 90 W  
Power Consumption in standby..................................... 1.0 W  
is a trademark placed on a product with  
Pioneer’s Phase Control Technology.  
The Technology enables high-grade 5.1ch with no delay  
in the bass area.  
8
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
目錄  
功能與特色  
)高功率 級擴大器,能提供如同  
D
此種具有寬廣動態範圍的音頻及視頻  
7
300 W RMS  
....................................................4  
功能與特色 .........................................4  
結合揚聲器運..................................4  
....................................................5  
揚聲器安裝 ..........................................5  
安裝注意事項 ......................................6  
面板設備.............................................6  
前面..................................................6  
後面..................................................6  
....................................................7  
線路位準接線 ......................................7  
....................................................7  
故障排除.............................................8  
....................................................8  
Dolby* Digital  
軟體播放。  
搭配  
的音效驅動裝置 (  
)。  
driver  
7
7
30 cm  
交頻可以設置到  
50 Hz 60 Hz 70 Hz 80 Hz  
100 Hz 120 Hz 160 Hz 200 Hz  
具備低音模式選擇器 (音樂/劇院模式。  
7
授權製造杜比與雙  
Dolby  
*
Dolby Laboratories  
標誌是  
的商標。  
Dolby Laboratories  
D
結合揚聲器運用  
結合了小型揚聲器的  
其頻率特性如下圖所示。  
S-LX70W  
如圖中所示,低頻範圍明顯獲得改善。  
這些獨特的特性均是在無迴音室內所測得的結果。只  
要安放的位置妥當,在一般聆聽室內加裝 S-LX70W  
重低音,便可以產生比圖表顯示更棒的效果。  
小型揚聲器 + S-LX70W  
配件  
小型揚聲器  
RCA 插頭連接線 × 1  
電源線 × 1  
頻率(Hz)  
Dolby* Digital  
在播放  
重低音來建立效果特殊的聲道;而在播放  
(低頻效果:此種音效有如來自地表的隆隆聲,功  
杜比數位音效時,建議您採用  
LFE  
音效  
拋光布× 1  
S-LX70W  
用在於加強影像所帶來的震撼力)時,  
低音能讓效果更具震撼有力。  
保證卡× 1  
操作手冊  
Dolby* Digital  
Dolby Digital  
Dolby Surround  
多聲道數位系統的名即是  
指的是自  
中所開發出來  
Dolby Surround  
Dolby  
Pro Logic Surround  
的延續。  
Dolby Digital  
擁有頻率範圍在  
5.1  
亦可視為是一種  
聲道系統。這是因其  
20 Hz 20 kHz  
內的五種聲道 (分別  
是左前右前置、中左後置以及右後置)以及一重  
LFE  
低音的獨立聲道。重低音聲道亦可視為是一種  
頻效果。  
(低  
LFE  
此種  
聲道的使用可根據個人品味來加強低音效果。  
4
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
2
1
3
安裝  
揚聲器安裝  
重低音安裝標準  
左置揚聲器  
1
2
3
4
4
右置揚聲器  
重低音建議安裝距離  
聆聽位置  
5
1
2
6
7
附註:  
為了能夠避免干擾附近的電視畫面採用經過防磁  
處理(magnetically shielded)的揚聲器系中置  
揚聲器位置通常最接近電視機,因此這點相當重要。  
請將左聲道與右聲道的揚聲器擺在電視機兩側距離  
相同的位置上,同時彼此應相距 1.8 m。  
3
4
請將中置揚聲器安裝在電視機的上方或下方此才  
能讓中置聲道的音效彷如就從電視畫面傳出來一樣。  
當將後置(環繞聲器直接相互平行地置放在聆聽  
者的兩或稍微後方一點的位高度大約在聆聽  
者耳朵上方1 m的地會是最有效果的安裝方。  
重低音是透過單聲道的方式來播放低音,實際上人類耳  
low-pitched  
敏感。也因此,重低 音幾乎可 以安裝 在任何 地方。然  
而,如果安裝位置相距太遠,其他揚聲器的音效亦可能  
會變得不自然。  
朵對於低調(  
)音效傳來的 方向不會太過  
注意:  
當要將中置揚聲器安裝在電視機上方,請確實利用膠  
帶或其他一些合適的方式將其固定。  
不然,揚聲器可能會因為受到地震等外力震動而掉落  
下來,導致附近的人受傷或揚聲器因此而受損。  
1
2
3
4
5
6
7
揚聲器安裝位置之範例  
左前置揚聲器  
中置揚聲器  
右前置揚聲器  
重低音揚聲器  
聆聽位置  
安裝注意事項  
請將本機安裝在溫度及濕度不致過高且通風良好的  
地方。  
左後置揚聲器  
右後置揚聲器  
請勿將本機擺放在烤箱或其他加熱設備附近陽光  
會直射到的地方免對外箱及內部零件造成不利影  
響。另外,請勿將本機安裝在灰塵太多或濕氣太重的  
地方,以免功能異常或發生故障請避免將本機安  
放在餐桌上或其他暴露在熱氣、蒸汽及油煙下的地  
方。)  
請勿將笨重或大型的物體放置於本機上樣做會導  
致本機掉落,從而造成損壞或人體受傷。若揚聲器從  
安裝位置掉下,將會使其面層發生無法修復的裂痕。  
請儘量避免將本機放在錄音機座等對磁場敏感設備  
的附近。  
5
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
後面板  
本揚聲器系統採防磁處理。  
仍需視安裝的位置而揚聲器系統如安裝得  
太過靠近電視機螢幕時可能會造成色彩失真。  
如果發生這種現象,請按下電源開關將電視機關閉,  
然後過  
分鐘後再打開。  
15 30  
如果問題仍在,請將揚聲器系統遠離電視機擺放。  
3
4
5
6
7
8
MIN  
MAX  
VOLUME  
80Hz  
100Hz  
70Hz  
120Hz  
60Hz  
160Hz  
200Hz  
50Hz  
請勿將本機放置於不穩定表面,否則將會導致本機跌  
落,從而造成損壞或人體受傷。  
CROSSOVER  
BYPASS  
ON  
OFF  
CINEMA  
USIC  
BASS MODE  
0∞  
80∞  
PHASE  
ON  
請勿將裝有液體的杯子、玻璃或其他容器放在本機  
上,因為如果液體溢出時,本機將會受到損壞。  
所選擇的安裝位置必須有堅固的地板表面免將揚  
聲器安裝在長毛地毯上為地毯會碰到驅動器的振  
動膜,從而導致聲音失真。  
OFF  
AUTO STANDBY  
LINE LEVEL  
OUTPUT INPUT  
AC IN  
請將本機遠離調諧器天線擺放,以免安裝位置大過接  
近天線而產生雜音。此時,使用本機請遠離天線,或  
在不需要播放重低音時關閉本機電源。  
9
11  
10  
1
(STANDBY/ON)  
電源指示燈  
電源打開時,會亮起藍燈AUTO STANDBY(自動待  
關打開時(ON每當揚聲器接收到音頻信,  
就會亮起藍燈。如果電源關閉時間短暫,電源在接通  
時,指示燈會亮起藍燈。如果超過12分鐘仍無信號出  
低音揚聲器會自動轉換為待機模電源指示  
燈則會亮起紅燈。其後,如果接收到,電源會自動接  
通,而電源指示燈也就亮起藍燈。  
外觀保養  
請用隨附的拋光布或其他細布、乾布來擦拭表面。  
外表很髒時,請用軟布沾上一些五倍清水稀釋的中  
性清潔劑澈底擰乾後擦拭,接著以乾布再擦拭一  
次。請勿使用傢俱蠟或清潔劑。  
嚴禁在本機上面或其附近使用稀釋劑、揮發油、除  
蟲噴劑或其他化學物品,以免腐蝕表面。  
附註:  
如果您準備長期間關掉本則請確認電源關閉後指  
示燈已經熄滅。  
面板設備  
2 電源開關 (POWER)  
按下此鍵可打開電源;再按時,則可關閉電源。  
前面板  
3 音量調整鈕 (VOLUME)  
可設定重低音的音量。  
請從最低音量 (MIN)的位置慢慢轉動旋鈕。  
使用本低音位準可以獨立設因此不必將影音  
擴大器上的低音音量提高。  
4 分頻旋鈕 (CROSSOVER)  
使用重低音請設定好頻率上限(50 Hz, 60 Hz, 70  
Hz, 80 Hz, 100 Hz, 120 Hz, 160 Hz, 200 Hz以便  
能夠補償其他揚聲器的輸使用到影音接收機的低  
音管理功能,請將其設定為 BYPASS ON,以便有機會  
使用影音接收機的低通濾波器(low-pass filter)來提  
高音效品質。  
POWER  
STANDBY/ON  
1
5 略過濾波開關 (BYPASS)  
2
設定在 ON 音頻信號會直接傳送至低音揚聲器上,  
而略過擴大器的濾波裝置。  
6 低音模式開關 (BASS MODE)  
MUSIC:特性頻率均會呈現較低的狀態。建議可用於  
音樂來源。  
CINEMA:低階頻率會加強議可用在對重低音有需  
求的來源。  
6
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
相位開關 (  
線路位準輸出端子 ( )  
LINE LEVEL OUTPUT  
7
PHASE 0º/180º)  
出的相位會呈現出與輸入信號反,  
9
設定為  
用於透過擴大器來連接其他設備。此插孔的信號輸出  
可藉由本機 上各種控制的設定讓其 不會受到任何影  
響。  
180º  
而設定為 時,則會呈現出與輸入信號同向。  
0º  
一般來說,此開關會設定在  
0º  
但當重低音與左、右置揚聲器之間的音效連結呈現出  
的位置。  
線路位準輸入端子  
10  
(LINE LEVEL INPUT)  
不自然的情形時,請嘗試切換至  
於音效自然的位置。  
並將開關設置  
180º,  
利用特別附贈的  
器的  
插頭連接線來連接擴大器或接收  
重低音前置輸出 端。  
RCA  
SUBWOOFER PREOUT (  
)
當將兩只以上的重低音一起使用確定這些重低音  
的相位開關均設定在相同的位置。  
11 AC IN  
將電源線連接於供電的重低音揚聲器的  
AC IN  
自動待機開關 (  
8
AUTO STANDBY  
用於打開或關閉自動待機裝置。  
打開開關時 ( 默認設置為  
將電源線連接於  
插座。  
AC  
S-LX70W音樂模式頻率響應  
自動待機裝  
ON  
OFF  
,
100  
置將被激活。在此模式下,如果在 分鐘內沒有輸入  
12  
未濾波  
90  
80  
70  
60  
50  
40  
信號,該系統會自動切換到待機。如果檢測到輸入信  
號,電源將自動再接通。  
附註:  
在自動待機模式下果所連接的部件輸出噪音或其  
他非音頻信號,也可能會導致本系統自動接通電源。  
在此情況下,請關閉自動待機模式,並用手動方式打  
開或關閉本系統。  
濾波頻率  
200 Hz分頻)  
10  
100  
1000  
10000  
頻率(Hz)  
接線  
進行或變更任何接線之前,請先關閉電源,並拔除  
插座上本機及擴大器/接收機的連接線。  
AC  
線路位準接線  
S-LX70W(後面板)  
附贈的RCA插頭連接線  
此種接線方式適用於配備  
(重低  
附註:  
在連接至擴大器或接收機上專為提供環繞中置聲道  
SUBWOOFER PREOUT  
音前置輸出端子)的擴大器或接收機。請利用特別附贈  
插頭連接線連至本機上的  
的前置輸出  
端子時,只能從中置聲道聽到  
RCA  
LINE LEVEL  
(PREOUT)  
低音效果,以這樣來說效果是不夠的。  
(線路位準輸入)端子。  
INPUT  
操作  
有關操作功能部份的詳細說明請參閱第 頁。  
操作擴大器或接收機並調整其他揚聲器的音量。  
6
2.  
打開電源 (  
)開關 ( 。  
POWER  
利用音量(  
)調整鈕( )調整低音的音量。  
VOLUME  
1.  
2
3.  
3
必要,請操作分頻CROSSOVER)鈕(4)及 位  
PHASE)開關(7),然後再利用音量(VOLUME)  
調整鈕(3)。將低音模式(BASS MODE)開關(6)  
設定在 MUSIC CINEMA 的位置。  
如果本機的電源線是連接至擴大器或接收機上的開關  
AC 輸出插座 , 且開關在 ON( ) 的位置時,那麼  
便可將擴大器或接收機與本機一起打開關閉。  
如果本機無法連接至擴大器或接收機上,那麼請先打  
開擴大器或接收機,然後再打開本機電源。在關閉電  
源時,請關閉本機電源,然後再關閉擴大器或接收機  
電源。  
關閉電源 ( )開關 ( 。  
POWER 2  
4.  
電源指示燈熄滅。  
7
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
故障排除  
人們經常錯將操作不當認為是系統故障或異常。如果您覺得本機有那裏不對勁,便請按以下各點進行檢查。有時問題  
可能是來自其他裝置。請仔細檢查其他使用中的裝置和電器設備。如果在查證過以下各點後問題仍未改善,則就近洽  
請您的  
授權服務中心或經銷商前來維修。  
PIONEER  
癥狀  
原因  
電源插頭未正確插好。  
排除辦法  
確實將插頭插好。  
沒有電源供應  
1
2
關時沒  
亮。)  
RCA  
插頭連接線的連接錯誤或  
請再檢查一次並正確接上。  
順時針慢慢轉動。  
沒有聲音  
附件  
未連接。  
音量 (  
(指示燈亮。)  
)調整鈕設定在  
)的位置。  
VOLUME  
最低音量 (  
MIN  
聲音失真。  
3
VOLUME  
調整鈕以  
位準太高。  
反時針轉動音量 (  
降低位準。  
輸入位準太高。  
反時針轉動擴大器的輸出位準(音量低  
音控制、低音加重)以降低位準。  
4
5
發出咆哮聲。  
無電源供應到擴音器。  
重低音位準設定太高。  
連接擴音器並供電。  
將重低音放在與揚聲器距離適當的位置  
上。反時針轉動音量 (  
鈕以降低音量。  
)調整  
VOLUME  
聆聽  
多。  
廣播時雜音太  
FM  
AM  
AM  
FM  
AM FM  
室內用本機之  
環型天線或  
室內天線與本  
增加  
機太過接近。  
間的距離。  
規格  
機箱 ........ 附有  
封閉箱 系統的落地式  
)
配件  
插頭連接線  
...............................................RCA  
CLOSED BOX(  
× 1  
× 1  
× 1  
× 1  
(磁屏蔽)  
圓錐體型  
電源線  
拋光布  
保證卡  
揚聲器  
................................................. 30 cm  
頻率響應  
設置於  
.........25 Hz 4000 Hz ( BYPASS ON)  
功率擴大器持續功率輸出 (  
操作手冊  
規格與設計如因改良而有所變動時,恕不另行通知。  
RMS  
....................................................300 W/4 (100 Hz)  
輸入 (  
/阻抗下之靈敏度)  
插孔)  
100 Hz  
線路位準 (  
RCA  
........................ 160 mV/33 kΩ  
輸出 (  
/阻抗下之位準)  
100 Hz  
線路位準 (  
插孔)  
RCA  
.......................... 160 mV/1 kΩ  
日本先鋒公司出版。  
可選擇分頻  
.......................50 Hz, 60 Hz, 70 Hz, 80 Hz,  
100 Hz, 120 Hz, 160 Hz, 200 Hz  
2007  
版權  
日本先鋒公司。  
版權所有。  
外部尺寸  
(寬)  
......362 mm  
重量 (不含外包裝)  
(高)  
(深)  
× 365 mm  
× 362 mm  
.........................................18.2 kg  
是採用先鋒相位控制技術的產品上的商標。  
電源需求  
此項技術使高級  
延。  
聲道變成可能,且在低音區毫無遲  
5.1  
台灣機型  
其他機型  
∼,  
∼,  
............................... 110 V  
................. 220 V 240 V  
50 Hz/60 Hz  
50 Hz/60 Hz  
功功率消耗  
..........................................................90 W  
待機時的功率消耗  
................................................1.0W  
8
ChH  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PIONEER CORPORATION  
4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654, Japan  
PIONEER ELECTRONICS (USA) INC.  
P.O. BOX 1540, Long Beach, California 90801-1540, U.S.A. TEL: (800) 421-1404  
PIONEER ELECTRONICS OF CANADA, INC.  
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada TEL: 1-877-283-5901, 905-479-4411  
PIONEER EUROPE NV  
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium TEL: 03/570.05.11  
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.  
253 Alexandra Road, #04-01, Singapore 159936 TEL: 65-6472-7555  
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.  
178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: (03) 9586-6300  
PIONEER ELECTRONICS DE MEXICO S.A. DE C.V.  
Blvd.Manuel Avila Camacho 138 10 piso Col.Lomas de Chapultepec, Mexico,D.F. 11000 TEL: 55-9178-4270  
K002_B_En  
Published by Pioneer Corporation.  
Copyright © 2007 Pioneer Corporation.  
All rights reserved.  
<SRD1343-A>  
Printed in China  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Video Game Keyboard KBD5000 User Manual
Philips Baby Accessories SCF147 User Manual
Philips Cassette Player AQ 6598 17 User Manual
Philips CRT Television 15PT2536 User Manual
Philips Iron GC1010 User Manual
Philips VCR VR20D User Manual
Poulan Tiller 184860 User Manual
Poulan Trimmer 530163516 User Manual
Precor Elliptical Trainer 521 User Manual
PYLE Audio Car Video System PLD58MUT User Manual