DJ Controller
DDJ-WEGO3
The Pioneer DJ support site shown above offers FAQs, information on software and various other types of
information and services to allow you to use your product in greater comfort.
Operating Instructions (DJ unit Setup)
Download from Www.Somanuals.com. All Manuals Search And Download.
For U.S.A.
11) Only use attachments/accessories specified by
the manufacturer.
1) Read these instructions.
2) Keep these instructions.
12) Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to
avoid injury from tip-over.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s
instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.
10) Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
13) Unplug this apparatus during lightning storms
or when unused for long periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the
apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
D3-7-13-69_En
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
D8-10-1-2_A1_En
FEDERAL COMMUNICATIONS COMMISSION DECLARATION OF CONFORMITY
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Product Name: DJ Controller
Model Number: DDJ-WEGO3-K, DDJ-WEGO3-W, DDJ-WEGO3-R
Responsible Party Name: PIONEER ELECTRONICS (USA) INC.
SERVICE SUPPORT DIVISION
Address: 1925 E. DOMINGUEZ ST. LONG BEACH, CA 90810-1003, U.S.A.
Phone: 1-800-421-1404
D8-10-4*_C1_En
Information to User
CAUTION
Alterations or modifications carried out without
appropriate authorization may invalidate the user’s
right to operate the equipment.
This product satisfies FCC regulations when shielded
cables (with Ferrite-cores attached) and connectors
are used to connect the unit to other equipment. To
prevent electromagnetic interference with electric
appliances such as radios and televisions, use
shielded cables (with Ferrite-cores attached) and
D8-10-2_A1_En
connectors for connections.
D8-10-3b_A1_En
En
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT NOTICE
THE MODEL NUMBER AND SERIAL NUMBER OF
THIS EQUIPMENT ARE ON THE REAR OR BOTTOM.
RECORD THESE NUMBERS ON PAGE 15 FOR
FUTURE REFERENCE.
D36-AP9-3*_A1_En
WARNING: This product contains chemicals known
to the State of California and other governmental
entities to cause cancer and birth defects or other
reproductive harm.
D36-P5_C1_En
4
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
How to read this manual
!
Thank you for buying this Pioneer product.
Be sure to read this booklet and the “Operating Instructions (DJ soft-
ware Setup)” provided on the Pioneer DJ support site. Both include
important information that should be fully understood before using
this product.
After you have finished reading the instructions, put them away in a
safe place for future reference.
!
!
This document describes the hardware operation methods. The
various DJ software usage methods are described in the “Operating
Instructions (DJ software Setup)”.
In this document, the product main unit button name and terminal
name is listed in [ ]. (Example: [CUE] button, [AUX IN] terminal)
Before start
Features....................................................................................................... 6
What’s in the box ........................................................................................ 6
Obtaining the Operating Instructions (DJ software Setup).................... 6
Preparing the software............................................................................... 6
Connections
Connecting with an iPhone/iPad .............................................................. 7
Connecting with a computer..................................................................... 8
Part names and functions
1 Power supply............................................................................................ 9
2 Browser..................................................................................................... 9
3 Deck ........................................................................................................ 10
4 Mixer ....................................................................................................... 10
Utility mode/Firmware update
Utilities modes .......................................................................................... 11
Firmware update....................................................................................... 11
Additional information
Troubleshooting........................................................................................ 12
About trademarks and registered trademarks ...................................... 13
Specifications............................................................................................ 13
En
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Compatibility with various DJ software
programs
Since it is compatible with MIDI, a variety of DJ software can be used to
perform hot cue, sampler, or other operations.
For the latest software support status, see the Pioneer DJ support site
below.
Before start
Features
The unit is a compact size DJ Controller that can stage DJ performances
using dynamic sound changes and a wide variety of light changes. With
use of an iPhone/iPad connection cable, DJ can be enjoyed even on an
iPhone/iPad, and not just on a computer.
Equipped with the “JOG FX” function enabling dynamic sound changes,
and the “PULSE CONTROL” function enabling a wide variety of changes
in light color using the LED of this unit.
The power source for this unit is compatible with AC adapter/USB path
power/USB power adapter, etc. enabling enjoying of DJ performances in
the style and preference of the user.
What’s in the box
!
!
!
!
!
!
!
!
Operating Instructions (DJ unit Setup) (This document)
AC adapter
Power cord
USB cable
Warranty (page 15 of this manual)
iPhone/iPad connection cable (Lightning)*
VIRTUAL DJ LE license key (indicated on this unit’s bottom panel)
djay for Mac license key (indicated on this unit’s bottom panel)
Hybrid DJ Controller
DJ Controller for enjoying DJ on a computer and on an iPhone/iPad.
Since user can use either computer or iPhone/iPad depending on the
situation, DJ can be enjoyed in a variety of DJ scenes.
* : iPhone/iPad connection cable (30-pin dock connector) is sold
separately.
For information related to the separately sold iPhone/iPad connection
cable (30-pin dock connector) and the latest supported models, see the
Pioneer DJ support site below.
iPhone/iPad CONNECTION
By connecting this unit with an iPhone/iPad using the iPhone/iPad con-
nection cable, the contents of the iPhone/iPad can easily be used for DJ
performances.
Caution
The license key cannot be reissued. Be careful not to lose it.
In addition, since the iPhone/iPad can be recharged even while DJing,
the DJ performances can be enjoyed without needing to worry about the
remaining battery charge.
Obtaining the Operating
Instructions (DJ software Setup)
JOG FX
The various instructions are sometimes provided as files in PDF for-
mat. Adobe® Reader® must be installed in order to view files in PDF
format.
This unit is equipped with a JOG FX function allowing multiple effects
to be controlled simultaneously with the jog dial. The parameters of
multiple effects can be controlled through the simple operation of turn-
ing the jog dial, so a wide variety of transformations of the sound can be
enjoyed.
1 Launch a web browser on the computer and access
the Pioneer DJ support site below.
Also, by using in combination with FX PULSE, DJ performances can be
staged with an extensive array of animations using LED lights.
2 On the Pioneer DJ support site, click [Manuals] under
[DDJ-WeGO3].
PULSE CONTROL
Stages DJ performance in animations with a fusion of sound and light.
3 Click on the required language on the download
!
Main animations for PULSE CONTROL
page.
1
LAUNCH PULSE
Downloading of the operating instructions begins.
When a track is loaded, LED light flows toward the jog dial, stag-
ing so that the user knows at a glance that the track has been
loaded.
Preparing the software
The driver software of this unit and the various DJ software are listed
in the Operating Instructions (DJ software Setup). See the Operating
Instructions (DJ software Setup) downloaded in Obtaining the Operating
Instructions (DJ software Setup), and prepare the necessary software.
2
FX PULSE
The LED lights on the jog dial move in various ways according
to the effect that is operated, adding excitement to the DJ per-
formance through the movement of the light in addition to the
changes in the sound.
3
BEAT PULSE
When the JOG FX mode is on, the blue LED on the JOG dial
brightens depending on the volume of the sound, to enable a
visual grasp of the sound volume.
Design
Achieves a flat, compact size that is easy to carry around, and does not
take up space when installed, for a smart, casual design.
Uses a round layout letting first-time DJ users to enjoy DJ without
feelings of difficulty and an aluminum panel on top that accentuates
simplicity.
In addition, a blue LED is mounted on the JOG dial to realize a fusion
of sound and light in the FX PULSE or other function, and this serves
to stage the DJ performance feel, and the enjoyment of sound
manipulation.
6
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Be sure to set the unit to standby mode and unplug the power cord from the power outlet before making or changing connections between devices.
Connect the power cord after all the connections between devices have been completed.
Be sure to use the power cord, AC adapter and USB cable included with this product.
Refer to the operating instructions for the component to be connected.
For the connection cables, check the position of the unit terminal, and connect correctly to the unit.
This unit can be used by connecting it to a computer using a USB cable, even without connecting the AC adapter.
!
!
!
!
!
Connect this unit and the computer directly using the included USB cable.
A USB hub cannot be used.
Connect the computer to which this unit is to be connected to an AC power supply.
The brightness of the buttons that light is dimmer when using on USB bus power.
When USB bus power is being used for operations, there will be situations like the following where the unit does not operate using USB bus power.
— The power supply is insufficient for USB bus power.
— When other USB devices are connected to the computer.
— When headphones with an impedance of less than 32 W are connected.
— When headphones are simultaneously connected to the stereo phone jack and the stereo mini-phone jack.
— When a monaural jack is connected to the [PHONES] terminal.
!
This unit may restart if the AC adapter or USB cable is disconnected during operation.
Connecting with an iPhone/iPad
Rear panel
Side panel
1
2
3
4
5
6
7
8
5
V
2100 mA
12V
R
L
DC IN
USB
iOS DEVICE
MASTER OUT
MIC
AC adapter (included)
iPhone/iPad
R
L
Headphones cord
To headphones
connection cable
Microphone cable
To microphone
USB cable (included)
DJ software
To audio input
terminals
For checking
the output sound
Audio cable
iPhone/iPad
Headphones
To USB port
For audio input
USB
L
R
Left
(L)
Right
(R)
Microphone
For power supply
Audio input
Power cord
(included)
USB Mobile battery /
USB power adapter
For audio output
Component, amplifier,
powered speaker, etc.
To power
outlet
!
!
!
!
This unit can use an iPhone/iPad connection cable to recharge on an iPhone/iPad. The unit can also be recharged while in Standby mode.
Connect an AC adapter when recharging an iPhone/iPad.
If power is supplied by USB bus power, iPhone/iPad recharging cannot be performed.
When the iPhone/iPad power is off, or when residual battery power has been exhausted, iPhone/iPad recharging cannot be performed.
En
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting with a computer
Since the iPhone/iPad connection has priority, do not connect an iPhone/iPad to the unit when using a computer.
Rear panel
Side panel
5
V
2100 mA
12V
R
L
DC IN
USB
iOS DEVICE
MASTER OUT
MIC
AC adapter (included)
USB cable (included)
To USB port
R
L
Headphones cord
To headphones
Microphone cable
Audio cable
To microphone
To audio input
terminals
For checking
the output sound
DJ software
For audio input
L
R
Left
(L)
Right
(R)
Computer
USB
Headphones
Microphone
Audio input
Power cord
(included)
For audio output
Component, amplifier,
powered speaker, etc.
To power
outlet
1 PHONES terminals
8 MIC terminal
Connect headphones here.
Connects a microphone here.
Both stereo phone plugs (Ø 6.3 mm) and stereo mini phone plugs
(Ø 3.5 mm) can be used.
!
!
Only the volume of the microphone’s sound can be adjusted.
Supports unbalanced input only.
!
Connect headphones with an impedance of 32 W or more.
Headphones with an impedance of less than 32 W are not
supported.
Caution when using the iPhone/iPad
stand
!
Do not connect headphones simultaneously to the stereo phone
jack and the stereo mini-phone jack.
iPhone/iPad stand
2 Cord hook
TEMPO
STANDBY ON
MASTER VOL
TEMPO
Secure the AC adapter’s power cord and USB cable on this hook.
!
The sound will be interrupted if the AC adapter’s power cord or
USB cable is disconnected from the unit during playback.
MIC VOL
BROWSE BACK
LOAD
A
HI
B
LOAD
HI
DJ CONTROLLER
3 DC IN terminal
!
!
!
!
This stand is exclusively for use with an iPhone/iPad. Do not place
tablets other than iPad or large devices on the stand.
Set the iPhone/iPad on the stand in the horizontal direction. It may
be unstable if set in the vertical direction.
Do not apply excessive force to the stand. Doing so may damage this
unit.
Please note that Pioneer will accept no responsibility whatsoever for
damage to or malfunction of the device, injury, etc., due to the device
falling, etc.
Do not move with an iPhone/iPad placed on the stand. The iPhone/
iPad could fall off.
Connect the included AC adapter’s DC plug here. Wait until all con-
nections of the equipment are completed before connecting the
power cord.
Be sure to use the power cord and AC adapter included with this
product.
4 USB terminal
When using a computer
!
Connect this unit and the computer directly using the included
USB cable.
!
!
!
A USB hub cannot be used.
If there is a cover on the iPhone/iPad, remove the cover before plac-
ing the iPhone/iPad on the stand. If the cover is left on, the iPhone/
iPad could be unstable.
When using an iPhone/iPad
!
If not using an AC adapter, connect this unit and a USB mobile
battery or USB power adapter using the included USB cable.
If power is supplied by USB bus power, iPhone/iPad recharging
cannot be performed. To recharge the iPhone/iPad, use an AC
adapter.
!
Using the cord hook
Fasten the AC adapter’s power cord and USB cable in place by hooking
them on the cord hook. This prevents the power cord and USB cable
from being accidentally pulled and the plugs from being disconnected
from the terminals.
!
USB bus power must have a power supply capacity of
DC 5 V/500 mA or greater. Note that depending on the capacity
and charging status of the product being used, operation may be
unstable.
Cord hook
USB cable
5 iOS DEVICE terminal
Connect this unit with the iPhone/iPad using the iPhone/iPad con-
nection cable.
12V
6 Kensington security slot
7 MASTER OUT terminals
DC IN
USB
Connect powered speakers, etc., here.
AC adapter’s power cord
8
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Part names and functions
4 Mixer
2 Browser
3
4 Mixer
1 Power supply
1
4
4
STANDBY ON
MASTER VOL
TEMPO
TEMPO
2
MIC VOL
l
8
m
9
5
5
BACK
BROWSE
LOAD
A
HI
B
LOAD
9
8
HI
DJ CONTROLLER
VOL
o
MID
MID
7
a
7
a
n
n
p
6
b
6
b
c
d
c
d
LOW
SELECT
MASTER
LOW
SYNC
SYNC
A
B
q
r
s
i
i
SHIFT
SHIFT
e
f
g
h
j k
e
f
g
h
j k
3 Deck
4 Mixer
3 Deck
* : The SHIFT function operation varies depending on the DJ software. For details, see the Pioneer DJ support site below.
1 Power supply
1 STANDBY/ON indicator
2 STANDBY/ON button
Shows the unit power status.
0
When unit power is on standby
— Press:
0
When red
The unit power is on standby.
When green
The unit power is on.
Turn on the power of this unit.
When unit power is on
— Press for over 1 second:
0
0
Set this unit’s power to the standby mode.
2 Browser
3 Rotary selector
4 LOAD button
!
Turn:
!
Press:
Select the track.
[SHIFT] + press:
Load the selected track to each deck.
[SHIFT] + press:
!
!
Operations differ depending on the DJ software.*
Operations differ depending on the DJ software.*
En
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Deck
5 TEMPO slider
d Jog dial
Adjusts the playing speed.
0
When JOG FX mode is off
— Scratch
When turned while touching a metallic part of the top of the
jog dial, the sound is played according to the direction and
speed at which the jog dial is turned.
— Pitch bend
The playing speed can be adjusted by turning the outer part
of the jog dial during playback.
— Search
6 Loop half button
!
Press:
Set the width of loop playback interval to 1/2 times.
[SHIFT] + press:
!
Operations differ depending on the DJ software.*
7 AUTO LOOP mode button
!
Press:
When loading a track to each deck, turning the jog dial while
holding down the [SHIFT] button enable move to playback
position at higher speed than scratch.
Turns the auto loop function on and off.
[SHIFT] + press:
!
Operations differ depending on the DJ software.*
0
When JOG FX mode is on
— JOG FX control
8 Loop double button
Effect parameters can be adjusted by turning the jog dial.
!
Press:
Set the width of loop playback interval to 2 times.
[SHIFT] + press:
Operations differ depending on the DJ software.*
e SHIFT button
!
When another button is pressed while pressing the [SHIFT] button, a
different function is called out.
9 FX1 button
f CUE button
!
Press:
!
Press:
Turns effect 1 on and off.
[SHIFT] + press:
Sets a cue point or moves the cue point.
[SHIFT] + press:
!
!
Switches the effect types of FX1.
The playing position moves to the beginning of the track.
a FX2 button
g Play/Pause button
!
Press:
Use this to play/pause tracks.
Turns effect 2 on and off.
[SHIFT] + press:
!
h Performance buttons
Switches the effect types of FX2.
0
When in hot cue mode
— Press:
b FX3 button
Sets the hot cue point.
— [SHIFT] + press:
!
Press:
Turns effect 3 on and off.
[SHIFT] + press:
Delete the hot cue set for that button.
When in sampler mode
— Press:
!
0
Switches the effect types of FX3.
Replays the sample sound.
— [SHIFT] + press:
c SYNC button
!
Press:
Operations differ depending on the DJ software.*
Synchronize the track tempo.
[SHIFT] + press:
!
i HOT CUE mode indicator
Operations differ depending on the DJ software.*
Lights up when the performance buttons are in hot cue mode.
j SAMPLER mode indicator
Lights up when the performance buttons are in sampler mode.
k HOT CUE/SAMPLER mode switching button
Switches the performance button mode to hot cue mode or sampler
mode.
4 Mixer
l MIC VOL control
p HEADPHONES SELECT MASTER button
Adjusts the audio level input to the [MIC] terminal.
Monitors the master sound over the headphones.
m MASTER VOL control
q HEADPHONES SELECT A/B buttons
Use this to monitor the sound of the respective decks over the
headphones.
Adjusts the sound level output from the master.
!
Not linked to [MASTER] on each DJ software screen.
n EQ (HI, MID, LOW) controls
r Channel faders
These adjust the sound quality input to the various decks.
[HI] (treble range), [MID] (middle range), [LOW] (low range)
Adjusts the sound level output from the various decks.
s Crossfader
o HEADPHONES VOL control
Switches the sound of the decks assigned to the left and right sides
of the crossfader for output.
Adjusts the audio level output from the [PHONES] terminal.
!
Not linked to [VOL] (headphone sound volume control) on each
DJ software screen.
!
The sound of the microphone connected to the [MIC] jack is not
output from the headphones.
10
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility mode/Firmware update
0 Pulse mode (illumination) setting
Utilities modes
The following settings can be changed:
This unit is equipped with two types of pulse mode (illumination lighted/
flashing mode).
!
!
!
Demo mode setting
Auto standby setting
Pulse mode (illumination) setting
Press the [HEADPHONES SELECT MASTER] button.
[HEADPHONES SELECT A] button lighted: Normal (Standard LED
lighted/flashing pattern)*
[HEADPHONES SELECT B] button lighted: Moderate (LED brightness
suppress lighted/flashing pattern)
Launching utilities mode
1 Sets the unit on standby status.
LED next to [STANDBY/ON] button on the upper right of the unit is in
red lighted status.
Firmware update
Firmware is the software required for controlling the unit.
To determine whether there is a firmware update for the unit, and to
download the update software, check the Pioneer DJ support site below.
2 While holding down the [LOAD] button on the left-
side deck and the [LOAD] button on the right-side deck,
press the [STANDBY/ON] button.
The unit starts up in utility mode. (The [SYNC] buttons on both decks
light up.)
Cautions
!
When performing a firmware update, first disconnect the iPhone/
iPad connection.
3 For items for which you would like to change the
!
Firmware updates for the unit cannot be performed on an iPhone/
iPad.
settings, change the settings.
See the Changing the settings below for the settings that can be
changed, and for the setting change methods.
A separate computer (Windows/Mac) is necessary.
1 Download the update software on the computer
4 Check that the [SYNC] button is in lighted state, and
then press the [STANDBY/ON] button to restart the unit.
Performing restart may be necessary to reflect the changed setting.
(Windows/Mac).
Download the update software from the Pioneer DJ support site below.
Caution
2 Connect this unit to your computer via a USB cable.
3 Press the [STANDBY/ON] button on the unit, and set
the unit to on status.
If the unit is in standby status, update cannot be performed.
When the [SYNC] button is flashing, this unit is writing the setting.
If the [STANDBY/ON] button is pressed to perform restart while the
[SYNC] button is flashing, the set values are not reflected in the unit.
4 Execute the update software that was downloaded in
Changing the settings
*: Setting upon purchase
Step 1.
When the update is complete, the unit goes into standby status.
5 Press the [STANDBY/ON] button on the unit, and set
the unit to on status.
The unit starts up with the updates applied.
0 Demo mode setting
After restarting the unit, if no operation is performed for a certain set
period, it starts in demo mode. The amount of time until start in this
demo mode can be changed.
Press the [HOT CUE/SAMPLER] mode switching button
on the left deck.
Left deck [1] button lighted: 10 min*
Left deck [2] button lighted: 5 min
Left deck [3] button lighted: 1 min
Left deck [CUE] button lighted: OFF
0 Auto standby setting
When the auto standby setting is on and if four hours have passed
while the following conditions are all met, the unit automatically enters
standby status.
!
No buttons or controls, etc. except for the [MIC VOL] control on the
unit are operated.
!
Audio signals are not input to this unit (excluding microphone audio
input).
Press the [HOT CUE/SAMPLER] mode switching button
on the right deck.
Right deck [1] button lighted: ON*
Right deck [CUE] button lighted: OFF
En
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional information
Troubleshooting
!
Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below and the [FAQ] for the [DDJ-WeGO3] on the Pioneer DJ support site.
Sometimes the problem may lie in another component. Inspect the other components and electrical appliances being used. If the problem cannot
be rectified, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
The player may not operate properly due to static electricity or other external influences. In such cases, normal operation may be restored by
unplugging the power cord then plugging it back in.
!
Problem
Check
Remedy
The power is not turned on.
Is the included USB cable properly connected?
Connect the included USB cable properly.
Connect to a USB port providing sufficient power.
Is the supply of power from the connected com-
puter’s USB port insufficient?
If devices not being used for the DJ performance are connected to other USB
ports, also disconnect them to provide sufficient power.
Try running the connected computer with the power supplied from an AC
adapter rather than running it on the battery.
Is the included AC adapter properly connected?
Is the [STANDBY/ON] indicator green?
Is the included USB cable properly connected?
Are you using a USB hub?
Connect the included AC adapter correctly.
Press the [STANDBY/ON] button to turn the power on.
Connect the included USB cable properly.
This unit is not recognized by the
computer.
USB hubs cannot be used. Connect the computer and this unit directly using
the included USB cable.
Is an iPhone/iPad connected?
—
Disconnect the iPhone/iPad.
The unit and DJ software controls and
sliders positions differ.
When the unit controls and sliders are moved, the DJ software controls and
sliders are synchronized.
Distorted sound.
Is the [MASTER VOL] control set to the proper
Adjust the [MASTER VOL] control according to the devices to be connected.
position?
Is the [HEADPHONES VOL] control set to the
Adjust the [HEADPHONES VOL] control according to the devices to be
proper position?
connected.
Is the sound level input to the [MIC] terminal set to Set the audio level input to the terminals to a suitable level for the connected
an appropriate level?
devices.
Sound being played is interrupted
when using DJ software.
Is the computer connected to this unit connected
to an AC power supply?
When using a notebook computer on battery power, the power management
system may set the battery energy saving mode, decreasing the CPU’s clock
frequency. If this happens, noise may be generated and operation may become
slower.
Connect the computer to which this unit is to be connected to an AC power
supply.
Is the driver software’s latency value suitable?
Set the driver software’s latency to a suitable value.
No sound or small sound.
Are the channel faders, crossfader and
[MASTER VOL] control set to the proper
positions?
Set the channel faders, crossfader and [MASTER VOL] control to the proper
positions.
Is the connected, power amplifier, powered speak- Properly set the external input selection, volume, etc., on the power amplifier,
ers, etc., properly set?
powered speakers, etc.
Are the connection cables properly connected?
Are the terminals and plugs dirty?
Is the driver software properly set? (Windows)
Connect the connection cables properly.
Clean the terminals and plugs before making connections.
Set the driver software properly. (With Mac OS X, no driver software is
necessary.)
Sound is interrupted when the ASIO
driver is set.
Has the ASIO driver been set with the DJ software Set the ASIO driver before starting up the DJ software.
started up?
Sound being played is interrupted
when using DJ software.
Is the driver software’s latency value suitable?
Set the driver software’s latency to a suitable value.
Set the DJ software’s latency to a suitable value.
When trying to update the firmware,
[Your DDJ-WeGO3 is not con-
nected.] is displayed.
Is an iPhone/iPad connected to the unit?
If an iPhone/iPad is connected to the unit, the computer cannot be recognized.
Disconnect the iPhone/iPad from the unit, and perform the update again.
The iPhone/iPad cannot be recharged. Are you using the unit on USB bus power?
Only when the unit is connected to an AC adapter, the iPhone/iPad can be
recharged.
Connect the unit and the AC adapter, and then connect the iPhone/iPad.
Is the [STANDBY/ON] indicator flashing?
Temporarily disconnect the connected iPhone/iPad, and check the connection
cable.
Is the iPhone/iPad power supply off?
If the iPhone/iPad power supply is off, iPhone/iPad recharging cannot be
performed.
Turn on the iPhone/iPad power supply, and connect to the unit.
Is the iPhone/iPad battery residual power
exhausted?
If the iPhone/iPad battery residual power is exhausted and the power supply can-
not be turned on, iPhone/iPad recharging cannot be performed.
Use the battery charger included in the iPhone/iPad to recharge the iPhone/
iPad, turn on the power supply and then connect to the unit.
12
En
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Check
Remedy
[STANDBY/ON] indicator is flashing.
—
If operation is abnormal, or it won’t start up, disconnect the AC adapter or USB
cable, wait for a little while, and then restart again.
If the symptoms still appear, put in a request for repairs.
Noise occurs in the sound.
—
When engaged in voice conversation or data transfer or receiving on the iPhone/
iPad, sound interruptions (communication noise) may occur in the unit. If these
symptoms occur, change the iPhone/iPad install location or orientation.
If this still does not improve the symptoms, turn off the iPhone/iPad mobile data
communications and use the Wi-Fi connection or turn on the flight mode.
About trademarks and registered
trademarks
!
!
Pioneer is a registered trademark of PIONEER CORPORATION.
The other names of companies, products, and technologies men-
tioned herein are the registered trademarks or trademarks of their
respective owners.
Specifications
AC adapter
Power............................................................AC 100 V to 240 V, 50 Hz/60 Hz
Rated current ......................................................................................... 0.6 A
Rated output............................................................................... DC 12 V, 2 A
Power consumption (standby)............................................................. 0.5 W
General – Main Unit
Power consumption
When an AC adapter is used
When connected to iPhone/iPad.......................... DC 12 V, 1 400 mA
When connected to a computer...............................DC 12 V, 300 mA
When using USB bus power..........................................DC 5 V, 500 mA
Main unit weight .......................................................................1.8 kg (4.0 lb)
Max. dimensions.........................380 mm (W) × 59 mm (H) × 240 mm (D)
(14.96 in. (W) × 2.32 in. (H) × 9.45 in. (D))
Tolerable operating temperature .........+5 °C to +35 °C (+41 °F to +95 °F)
Tolerable operating humidity ...................... 5 % to 85 % (no condensation)
Audio Section
Rated output level
MASTER OUT............................................................................ 3.2 Vrms
Total harmonic distortion (20 Hz to 20 kHzBW)
MASTER OUT..............................................................................0.006 %
Frequency characteristic
MASTER OUT................................................................. 20 Hz to 20 kHz
S/N ratio (rated output, A-WEIGHTED)
MASTER OUT................................................................................. 95 dB
Input impedance
MIC .................................................................................................. 11 kW
Output impedance
MASTER OUT....................................................................... 1 kW or less
PHONES ................................................................................ 10 W or less
USB AUDIO......................................... 24 bit/Fs: 44.1 kHz, 24 bit/Fs: 48 kHz
16 bit/Fs: 44.1 kHz, 16 bit/Fs: 48 kHz
Input / Output terminals
MASTER OUT output terminal
RCA pin jacks....................................................................................1 set
PHONES output terminal
Stereo phone jack (Ø 6.3 mm) .........................................................1 set
Stereo mini phone jack (Ø 3.5 mm).................................................1 set
MIC input terminal
Phone jack (Ø 6.3 mm).....................................................................1 set
USB terminal
B type.................................................................................................1 set
iOS device connection terminal
13-pin.................................................................................................1 set
!
For improvement purposes, specifications and design of this unit
and the driver software are subject to change without notice.
En
13
Download from Www.Somanuals.com. All Manuals Search And Download.
14
En
Download from Www.Somanuals.com. All Manuals Search And Download.
PIONEER ELECTRONICS (USA) INC.
LIMITED WARRANTY
WARRANTY VALID ONLY IN THE U.S.A. AND CANADA
WARRANTY
Pioneer Electronics (USA) Inc. (PUSA) warrants that products distributed by PUSAin the U.S.A. and Canada that fail to function properly under normal use due to a manufacturing
defect when installed and operated according to the owner’s manual enclosed with the unit will be repaired or replaced with a unit of comparable value, at the option of PUSA,
without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of PUSA.
THISLIMITEDWARRANTYAPPLIESTOTHEORIGINALORANYSUBSEQUENTOWNEROFTHISPIONEERPRODUCTDURINGTHEWARRANTYPERIODPROVIDEDTHE
PRODUCTWAS PURCHASED FROM AN AUTHORIZED PIONEER DISTRIBUTOR/DEALER INTHE U.S.A. OR CANADA. YOUWILL BE REQUIREDTO PROVIDE A SALES
RECEIPT OR OTHERVALID PROOF OF PURCHASE SHOWINGTHE DATE OF ORIGINAL PURCHASE OR, IF RENTED,YOUR RENTAL CONTRACT SHOWINGTHE PLACE
AND DATE OF FIRST RENTAL. IN THE EVENT SERVICE IS REQUIRED, THE PRODUCT MUST BE DELIVERED WITHIN THE WARRANTY PERIOD, TRANSPORTATION
PREPAID, ONLY FROMWITHINTHE U.S.A. AS EXPLAINED INTHIS DOCUMENT. YOUWILL BE RESPONSIBLE FOR REMOVAL AND INSTALLATION OFTHE PRODUCT.
PUSAWILLPAYTO RETURNTHEREPAIREDORREPLACEMENTPRODUCTTOYOUWITHINTHEU.S.A.
Parts
Labor
PRODUCT WARRANTY PERIOD
DJ Audio and Video ...................................................................................................................................................................................
1 Year
1 Year
The warranty period for retail customers who rent the product commences upon the date product is first put into use (a) during the rental period or (b) retail sale, whichever occurs first.
WHAT IS NOT COVERED
IFTHIS PRODUCTWAS PURCHASED FROM AN UNAUTHORIZED DISTRIBUTOR,THERE ARE NOWARRANTIES, EXPRESS OR IMPLIED, INCLUDINGTHE IMPLIEDWARRANTY
OF MERCHANTABILITY ANDTHE IMPLIEDWARRANTY OF FITNESS FOR A PARTICULAR PURPOSE ANDTHIS PRODUCT IS SOLD STRICTLY “AS IS” AND“WITH ALL FAULTS".
PIONEER SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL AND/OR INCIDENTAL DAMAGES.
THIS WARRANTY DOES NOT APPLY IF THE PRODUCT HAS BEEN SUBJECTED TO POWER IN EXCESS OF ITS PUBLISHED POWER RATING.
THISWARRANTY DOES NOT COVERTHE CABINET OR ANY APPEARANCE ITEM,USER ATTACHED ANTENNA, ANY DAMAGETO RECORDS OR RECORDINGTAPES OR DISCS, ANY
DAMAGETOTHE PRODUCT RESULTING FROM ALTERATIONS, MODIFICATIONS NOT AUTHORIZED INWRITING BY PIONEER,ACCIDENT, MISUSE OR ABUSE, DAMAGE DUETO
LIGHTNINGORTO POWERSURGES,SUBSEQUENTDAMAGEFROMLEAKING,DAMAGEFROMINOPERATIVEBATTERIES,ORTHEUSEOFBATTERIESNOTCONFORMINGTOTHOSE
SPECIFIEDINTHEOWNER’SMANUAL.
THISWARRANTY DOES NOT COVERTHE COST OF PARTS OR LABORWHICHWOULD BE OTHERWISE PROVIDEDWITHOUT CHARGE UNDERTHISWARRANTY OBTAINED FROM
ANYSOURCEOTHERTHANAPIONEERAUTHORIZEDSERVICECOMPANYOROTHERDESIGNATEDLOCATION. THISWARRANTYDOESNOTCOVERDEFECTSORDAMAGECAUSED
BYTHEUSEOFUNAUTHORIZEDPARTSORLABORORFROMIMPROPERMAINTENANCE.
ALTERED, DEFACED, OR REMOVED SERIAL NUMBERS VOID THIS ENTIRE WARRANTY
NO OTHER WARRANTIES
PIONEER LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITEDTO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE,TO A PERIOD NOTTO EXCEEDTHE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTERTHE WARRANTY PERIOD.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND SOME STATES DO NOT ALLOWTHE EXCLUSIONS OR LIMITATIONS
OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SOTHE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLYTOYOU. THISWARRANTY GIVESYOU SPECIFIC LEGAL
RIGHTS ANDYOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATETO STATE.
TO OBTAIN SERVICE
PUSA has appointed a number of Authorized Service Companies throughout the U.S.A. and Canada should your product require service. To receive warranty service you
need to present your sales receipt or, if rented, your rental contract showing place and date of original owner’s transaction. If shipping the unit you will need to package it
carefully and send it, transportation prepaid by a traceable, insured method, to an Authorized Service Company. Package the product using adequate padding material to
prevent damage in transit. The original container is ideal for this purpose. Include your name, address and telephone number where you can be reached during business
hours.
On all complaints and concerns in the U.S.A. and Canada call Customer Support at 1-800-872-4159.
For hook-up and operation of your unit or to locate an
Authorized Service Company, please call or write:
CUSTOMER SUPPORT
PIONEER ELECTRONICS (USA) INC.
P.O. BOX 1720
LONG BEACH, CALIFORNIA 90801
1-800-872-4159
DISPUTE RESOLUTION
Following our response to any initial request to Customer Support, should a dispute arise between you and Pioneer, Pioneer makes available its Complaint Resolution Program
to resolve the dispute. The Complaint Resolution Program is available to you without charge. You are required to use the Complaint Resolution Program before you exercise
any rights under, or seek any remedies, created by Title I of the Magnuson-MossWarranty-FederalTrade Commission Improvement Act, 15 U.S.C. 2301 et seq.
To use the Complaint Resolution Program call 1-800-872-4159 and explain to the customer service representative the problem you are experiencing, steps you have taken
to have the product repaired during the warranty period and the name of the authorized Distributor/Dealer from whom the Pioneer product was purchased. After the complaint
has been explained to the representative, a resolution number will be issued. Within 40 days of receiving your complaint, Pioneer will investigate the dispute and will either:
(1) respond to your complaint in writing informing you what action Pioneer will take, and in what time period, to resolve the dispute; or (2) respond to your complaint in writing
informing you why it will not take any action.
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No. ____________________________________________ Serial No. _________________________________________ Purchase Date ______________________
Purchased From ____________________________________________________________________________________________________________________________
_
KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE
UCP0212
En
15
Download from Www.Somanuals.com. All Manuals Search And Download.
To register your product, find the nearest authorized service location, to
purchase replacement parts, operating instructions, or accessories,
please go to one of following URLs :
Pour enregistrer votre produit, trouver le service après-vente agréé le plus
proche et pour acheter des pièces de rechange, des modes d’emploi ou
des accessoires, reportez-vous aux URL suivantes :
In the USA & Canada/Aux Etats-Unis & Canada
S018_B1_EnFr_PSV
© 2014 PIONEER CORPORATION.
All rights reserved.
PIONEER CORPORATION
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi, Kanagawa 212-0031, Japan
PIONEER ELECTRONICS (USA) INC.
P. O. BOX 1720, Long Beach, California 90801-1720, U.S.A. TEL: (800) 421-1404
K002_PSV_CU
Printed in
<DRH1289-A>
Download from Www.Somanuals.com. All Manuals Search And Download.
|