Pioneer Home Theater System HTZ 434DVD User Manual

Setting up your DVD/CD Receiver  
When connecting this system or changing connections, be sure to switch the power off with the STANDBY/ON button, and disconnect the power cord from the AC outlet.  
Do not use these speakers with any other system or amplifier as this may result in damage or fire.  
Using the remote control  
Additional notes on connecting antennas  
Keep antenna cables away from the main unit and other  
cables.  
To assure optimum reception, pull the FM antenna so that it is  
fully extended and not coiled or hanging at the rear of the unit.  
If reception with the supplied antenna is poor, see the Other  
connections section in the main operating instructions for details  
Check that you have all the accessories, then put  
the batteries in the remote control.  
Connect the AM and FM antennas to the rear panel of the DVD/CD receiver.  
The remote control can be used within a range of about 7  
meters from the remote sensor on the front panel, and  
within a 30 degree angle.  
2
1
Precautions:  
The remote control may not work if there is an obstacle  
between the remote control and the display unit, or if the  
remote control is not directed towards the remote sensor  
of the display unit at the correct angle.  
The remote control may not work properly if strong  
light such as direct sunlight or fluorescent light is shining  
onto the units remote sensor.  
The remote control may not work properly when this  
unit is used near devices emitting infrared rays, or when  
remote controls of other devices which use infrared rays  
are used. Also, the use of this remote control may cause  
other devices to work improperly.  
When the operating range of the remote becomes too  
short, replace the batteries.  
Batteries and  
remote control  
Pull off the protective shields  
of both AM antenna wires.  
1
2
on connecting outdoor antennas.  
STANDBY/ON  
fig. A  
fig. B  
fig. C  
CD  
FM/AM  
TUNER  
L1/L2  
LINE  
DVD  
TV  
Power cord*  
FRONT  
Additional notes on speaker placement  
SURROUND  
OPEN CLOSE  
0
Push open the tabs, then insert  
one wire fully into each terminal.  
8
3
7
* Illustration shows the Taiwan model  
If your listening room is of adequate size, place the speakers as  
shown in step 3 to achieve the optimum surround sound effect.  
If you are listening in a fairly small room and a typical surround  
speaker setup is not possible, see Home theater sound setup in  
the instruction manual and the Speaker Setup guide for  
information on the Front surround 3-spot setup option.  
When using the standard surround speaker setup as shown in  
step 3, please observe the following guidelines:  
Install the main front left and right speakers at an equal  
distance from the TV.  
For optimum effect, install the rear speakers slightly above ear  
level.  
1
4
¡
4
4
DVD MENU  
RETURN  
TUNE+  
ST–  
ST+  
ENTER  
BASS  
TUNE–  
MUTE  
MODE  
Release the tabs to secure the AM  
antenna wires.  
3
4
MASTER  
VOLUME  
Video cord  
FM antenna  
6
TV CONTROL  
CH  
INPUT  
VOL  
OPEN  
1
Fix the AM loop antenna to the  
attached stand.  
Remote control battery caution  
Incorrect use of batteries may cause leakage or  
rupture.  
Always be sure to follow these guidelines:  
Always insert batteries into the battery compartment  
2
To fix the stand to the antenna, bend in the  
direction indicated by the arrow (fig. A) then  
clip the loop onto the stand (fig. B).  
Install the center speaker above or below the TV so that the  
sound of the center channel is localized at the TV screen.  
3
FM  
AM  
ANTENNA  
UNBAL 75  
LOOP ANTENNA  
AM loop antenna  
Precautions:  
correctly matching the positive ª and negative ·  
polarities, as shown by the display inside the  
compartment.  
When installing the center speaker on top of the TV, be sure  
Note: If you plan to mount the AM antenna  
to a wall or other surface, secure the stand  
with screws (fig. C) before clipping the loop  
to the stand. Make sure the reception is clear.  
to secure it with tape or some other suitable means. Otherwise,  
the speaker may fall from the TV due to external shocks such as  
earthquakes, endangering those nearby or damaging the speaker.  
Microphone  
Never mix new and used batteries.  
Batteries of the same size may have different voltages,  
(for Auto MCACC setup)  
Do not connect the supplied speakers with any other  
amplifier. This may result in malfunction or fire.  
The front, center and surround speakers supplied with this  
depending on brand. Do not mix different brands of  
batteries.  
3
1
2
When disposing of used batteries, please comply with  
system are magnetically shielded. However, depending on the  
installation location, color distortion may occur if the speaker is  
installed extremely close to the screen of a television set. If this  
happens case, turn the power switch of the television set OFF,  
and turn it ON after 15 to 30 minutes. If the problem persists,  
place the speaker system away from the television set.  
Place the AM antenna on a flat  
surface and point in the direction  
giving the best reception.  
Don’t let it come into contact with metal  
objects and avoid placing near computers,  
television sets or other electrical appliances.  
5
6
Connect the FM wire antenna to the FM UNBAL 75antenna terminal.  
For best results, extend the FM antenna fully and fix to a wall or door  
frame. Dont drape loosely or leave coiled up.  
governmental regulations or environmental public  
instruction's rules that apply in your country or area.  
In order to prevent battery leakage, remove the  
batteries when not using the remote control for an  
extended period (one month or more). If leakage occurs,  
carefully wipe away any battery fluid inside the  
Note: The signal earth (H) is designed to reduce noise that occurs when an  
antenna is connected. It is not an electrical safety earth.  
The subwoofer is not magnetically shielded and so should not  
compartment, and replace the batteries with new ones.  
be placed near a TV or monitor. Since it is not magnetically  
shielded, do not place any magnetic storage media (such as floppy  
disks and tape or video cassettes) close to the subwoofer.  
Do not allow books or other objects to rest on top of  
the remote control, since the buttons may be depressed,  
causing faster exhaustion of the batteries.  
Do not fix the front, center speakers and subwoofer to the  
wall or ceiling; they could cause injury if they fell.  
Connect each speaker as shown below.  
Connect each speaker using the color-coded  
speaker cords. Match them to the colored  
speaker terminals on the rear panel of the  
DVD/CD receiver.  
3
Color-coded wire  
(Connect to speaker)  
Connect the DVD/CD receiver to your TV, then connect the  
supplied power cord.  
4
Surround right  
(Grey)  
Surround left  
(Blue)  
Color-coded connector  
(Connect to rear panel)  
Connect one end to a video input on your TV.  
Use the supplied video cord.  
1
Twist and pull off the protective  
shields on each wire.  
1
Connect the other end to the video output of the DVD/CD receiver.  
This player is equipped with copy protection technology. Do not connect this  
player to your TV via a VCR using AV cables, as the picture from this player will not  
appear properly on your TV.  
2
* Illustration shows the Taiwan model  
Connect the wires to the  
2
IN  
IN  
OUT  
Connect the power cord to the AC inlet.  
speaker. Match the colored  
wire with the color-coded  
label (above the tabs), then  
insert the colored wire into  
the red (+) tab and the other  
wire with the black (–) tab.  
3
MCACC  
6
FRONT  
MIC  
6
CENTER  
L
Listening position  
SPEAKERS  
6
L
L
R
AUDIO  
Subwoofer (Purple)  
TV  
LINE 1  
6
R
R
VIDEO IN  
6
6
SURROUND  
SUB  
WOOFER  
Connect the other end to the color-  
3
coded speaker terminals on the  
rear of the DVD/CD receiver (as  
shown at left). Make sure to insert  
completely.  
OPTICAL IN  
IN  
IN  
IN  
OUT  
AUDIO  
MCACC  
MIC  
6
FRONT  
6
CENTER  
L
CONTROL  
LINE  
2
FM  
SPEAKERS  
L
6
L
ANTENNA  
UNBAL
COMPONENT  
VIDEO OUT  
R
Y
TV AUDIO LINE  
1
PB  
6
Center (Green)  
R
R
6
6
AC IN  
SURROUND  
SUB  
PR  
VIDEO  
OUT  
VIDEO  
OUT  
S-VIDEO  
OUT  
WOOFER  
For the best surround sound, setup your speakers as  
above. The front left and right speakers should be  
about 1.82.7 m apart.  
VIDEO  
VIDEO  
Upper three terminals  
The small lug at the wire-end of the  
* Illustration shows  
the Taiwan model  
speaker plug should face up or  
down depending on whether it's  
being plugged into one of the  
upper or lower three speaker  
terminals. Please make sure to  
AC IN  
Front left  
(White)  
Front right  
(Red)  
To AC outlet  
These speaker terminals can be hazardous when live. When you connect or  
disconnect the speaker cables, to prevent the risk of electric shock, do not  
touch uninsulated parts before disconnecting the power cord.  
Congratulations! You're done setting up.  
connect correctly.  
Lower three terminals  
Printed in  
<XRE3103-A>  
Speaker Setup Guide  
Placing the Subwoofer (Taiwan model only)  
Assembling the speaker stands and securing your front speakers  
Safety precautions  
when setting  
What's in the box  
Choose your subwoofer placement  
Attach the speaker stand bases to the stems using the screws provided.  
Before securing the base to the stand, thread the speaker wire through the holes provided on the  
base as shown below. Then, once you have aligned the stem and base, secure with the small  
screws at the points shown at right.  
• Front speakers x 2  
• Center speaker x 1  
• Surround speakers x 2  
• Subwoofer x 1  
• Front speaker stand bases  
x 2  
• Screws (for bases) x 6  
• Brackets x 2  
The subwoofer supplied with this  
system can be placed upright or  
Flat position  
Upright position  
When assembling the speakers, lay  
them down flat on their side to avoid  
accidents or injury. Make sure to use  
a stable surface when assembling,  
setting up, and placing the speakers.  
on its side (flat). Choose the  
position that works best for your  
room, then attach the large non-  
skid pads as shown at right.  
• Speaker cords:  
• Screws (for brackets) x 4  
Red/White (Front speakers)  
4 m x 2  
Mounting brackets x 2  
Screws  
*
Green (Center speaker) 4 m x 1  
Blue/Grey (Surround speakers)  
10m x 2  
Purple (Subwoofer) 4 m x 1  
• Non-skid pads (small) x 4  
• Non-skid pads (large)  
Taiwan model x 4  
(for mounting brackets) x 2  
*
* Please refer to Wall-mounting  
the front and surround speaker  
system in the operating  
instructions for installation.  
All other models x 6  
Attach the non-skid pads to the Subwoofer  
(Singapore/Indonesia/Hong Kong/Phillipines/Malaysia models)  
Caution  
Standard surround 5-spot setup  
This is a standard multichannel surround sound speaker  
setup for optimal 5.1 channel home theatre sound.  
Connect the speaker system.  
2
Refer to the Setting up your DVD/CD Receiver (the other part of this  
setup guide) to connect the speakers properly. Place them as  
shown in the diagram at far left optimal surround sound.  
Please don't use the any attachments with the front speakers  
other than the brackets provided.  
Attach the large non-skid pads to the base of the subwoofer.  
Use the supplied adhesive to attach 6 pads to the base of subwoofer.  
Attach the smaller non-skid pads to the  
base of the center speaker.  
Use the supplied adhesive to attach 4 pads to the  
base of center speaker.  
1
Front  
left  
Front  
right  
: Non-skid pads  
Center  
Subwoofer  
Surround  
left  
Surround  
right  
Listening position  
Center speaker  
* Illustration shows the Taiwan model  
Front surround  
3-spot setup  
Attach the smaller non-  
Secure the speaker wire.  
When you're finished, thread  
the surround speaker cords  
through the outlet on the  
back of the speaker stand and  
through the base of the  
Secure in position with the brackets provided.  
Place the surround speakers on top of the front  
3
1
2
5
Line up the holes in the bracket with the holes in the speakers, then secure  
with two screws at the points shown below. Make sure you've matched the  
right and left brackets with the speakers (as shown).  
skid pads to the base of  
speakers, turn the surround speakers towards  
the closest wall, lining the arrows up for  
optimal Front Surround.  
the center speaker.  
Use the supplied adhesive to  
attach 4 pads to the base of  
center speaker.  
This setup is ideal when rear surround speaker placement  
isnt possible or you want to avoid running long speaker  
cables in your listening area.  
Turn each surround speaker so that the arrow at the base  
is lined up with the FRONT SURROUND arrow on the front  
speaker. This is only necessary with the FrtMovie or  
FrtMusic modes. With ExtPower (Extra Power), the  
surround speakers should be in the same direction as the  
front speakers (as shown below). See the operating  
instructions for more on the Front Surround modes.  
brackets as shown below.  
Surround  
left  
Surround  
right  
Front  
left  
Front  
right  
Center speaker  
Center  
Subwoofer  
FrtMovie / FrtMusic  
ExtPower  
Connect the speaker system.  
Refer to the Setting up your DVD/CD Receiver (the other part of this setup guide) to  
4
Listening position  
connect the speakers properly.  
* Illustration shows the Taiwan model  
FrtMovie / FrtMusic  
ExtPower  
Caution  
Please don't use the any attachments with the  
front speakers other than the brackets provided.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Automobile Accessories 12258ECO User Manual
Philips Car Satellite TV System 32PFL3406H User Manual
Philips Headphones SBC HC065 User Manual
Philips Headphones SBCHP 625 00 User Manual
Philips Headphones SHE3600 User Manual
Philips Microwave Oven 3164965063 User Manual
Philips Stereo System DC910W User Manual
Philips Stereo System FW V39 User Manual
Polk Audio Speaker System SR52505 User Manual
Polycom Conference Phone VTXTM 1000 User Manual