Pioneer Car Video System AVH P2300DVD User Manual

Owners Manual  
DVD RDS AV RECEIVER  
AVH-P2300DVD  
English  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
3
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
01  
Precautions  
IMPORTANT SAFEGUARDS  
Please read all of these instructions regarding  
your display and retain them for future refer-  
ence.  
WARNING  
!
Do not attempt to install or service your  
display by yourself. Installation or servi-  
cing of the display by persons without  
training and experience in electronic  
equipment and automotive accessories  
may be dangerous and could expose you  
to the risk of electric shock or other  
hazards.  
1
Read this manual fully and carefully be-  
fore operating your display.  
2
Keep this manual handy as a reference for  
operating procedures and safety informa-  
tion.  
3
4
5
Pay close attention to all warnings in this  
manual and follow the instructions care-  
fully.  
Do not allow other persons to use this sys-  
tem until they have read and understood  
the operating instructions.  
To ensure safe driving  
WARNING  
!
LIGHT GREEN LEAD AT POWER CON-  
NECTOR IS DESIGNED TO DETECT  
PARKED STATUS AND MUST BE CON-  
NECTED TO THE POWER SUPPLY SIDE  
OF THE PARKING BRAKE SWITCH. IM-  
PROPER CONNECTION OR USE OF  
THIS LEAD MAY VIOLATE APPLICABLE  
LAW AND MAY RESULT IN SERIOUS IN-  
JURY OR DAMAGE.  
Do not install the display where it may (i)  
obstruct the drivers vision, (ii) impair the  
performance of any of the vehicles oper-  
ating systems or safety features, includ-  
ing air bags, hazard lamp buttons or (iii)  
impair the drivers ability to safely oper-  
ate the vehicle.  
Do not operate this display if doing so in  
any way will divert your attention from  
the safe operation of your vehicle. Always  
observe safe driving rules and follow all  
existing traffic regulations. If you experi-  
ence difficulty in operating the system or  
reading the display, park your vehicle in a  
safe location and make necessary adjust-  
ments.  
Please remember to wear your seat belt at  
all times while operating your vehicle. If  
you are ever in an accident, your injuries  
can be considerably more severe if your  
seat belt is not properly buckled.  
Never use headphones while driving.  
To promote safety, certain functions are  
disabled unless the parking brake is on,  
and the vehicle is not in motion.  
6
!
!
!
To avoid the risk of damage and injury and the  
potential violation of applicable laws, this unit  
is not for use with a video screen that is visible  
to the driver.  
To avoid the risk of accident and the potential  
violation of applicable laws, no viewing of  
front seat video should ever occur while the  
vehicle is being driven.  
In some countries or states the viewing of  
images on a display inside a vehicle even by  
persons other than the driver may be illegal.  
Where such regulations apply, they must be  
obeyed and this units DVD features should  
not be used.  
7
8
9
When you attempt to watch a video image  
while driving, the warning Viewing of front  
seat video source while driving is strictly  
prohibited. will appear on the front display.  
To watch a video image on the front display,  
park your vehicle in a safe place and apply the  
parking brake.  
10 Never set the volume of your display so  
high that you cannot hear outside traffic  
and emergency vehicles.  
4
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Precautions  
01  
backing up. Do not use for entertainment pur-  
poses.  
Parking brake interlock  
Certain functions (Video viewing and certain  
touch panel keys) offered by this unit could be  
dangerous and/or unlawful if used while driv-  
ing. To prevent such functions from being  
used while the vehicle is in motion, there is an  
interlock system that senses when the parking  
brake is set. If you attempt to use the functions  
described above while driving, they will be-  
come disabled until you stop the vehicle in a  
safe place, and (1) apply the parking brake, (2)  
release the parking brake, and then (3) apply  
the parking brake again. Please keep the  
brake pedal pushed down before releasing the  
parking brake.  
!
Please note that the edges of the rear view  
camera images may differ slightly according  
to whether full screen images are displayed  
when backing up, and whether the images are  
used for checking the rear when the vehicle is  
moving forward.  
To avoid battery exhaustion  
Keep the vehicle engine running when using  
this unit to avoid draining the battery power.  
!
When no power is supplied to this unit,  
such as when the vehicle battery is being  
replaced, the microcomputer of this unit re-  
turns to its initial condition. We recom-  
mend that you transcribe the audio  
adjustment data.  
When using a display  
connected to V OUT  
This units V OUT is for connection of a dis-  
play to enable passengers in the rear seats to  
watch the DVD or Video CD.  
WARNING  
Do not use with vehicles that do not feature an  
ACC position.  
WARNING  
NEVER install the rear display in a location  
where the driver can watch a DVD while driving.  
When using the rear view camera  
With an optional rear view camera, this unit  
can be used as an aid to keep an eye on trai-  
lers, or when backing into a tight parking spot.  
WARNING  
SCREEN IMAGE MAY APPEAR RE-  
VERSED.  
USE INPUT ONLY FOR REVERSE OR  
MIRROR IMAGE REAR VIEW CAMERA.  
OTHER USE MAY RESULT IN INJURY  
OR DAMAGE.  
!
!
CAUTION  
!
The rear view camera function is to be used  
as an aid to keep an eye on trailers, or while  
5
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
02  
Before you start  
!
Once you have established a comfortable  
sound level, set the dial and leave it there.  
This device complies with part 15 of the FCC  
Rules. Operation is subject to the following  
two conditions:  
(1) This device may not cause harmful interfer-  
ence, and (2) this device must accept any inter-  
ference received, including interference that  
may cause undesired operation.  
BE SURE TO OBSERVE THE FOLLOWING  
GUIDELINES:  
!
!
!
Do not turn up the volume so high that you  
cant hear whats around you.  
Use caution or temporarily discontinue use  
in potentially hazardous situations.  
Do not use headphones while operating a  
motorized vehicle; the use of headphones  
may create a traffic hazard and is illegal in  
many areas.  
Information to User  
Alteration or modifications carried out without  
appropriate authorization may invalidate the  
users right to operate the equipment.  
About this unit  
The tuner frequencies on this unit are allo-  
cated for use in North America. Use in other  
areas may result in poor reception.  
For Canadian model  
This Class B digital apparatus complies with  
Canadian ICES-003.  
WARNING  
Handling the cord on this product or cords asso-  
ciated with accessories sold with the product  
may expose you to chemicals listed on proposi-  
tion 65 known to the State of California and other  
governmental entities to cause cancer and birth  
defect or other reproductive harm. Wash hands  
after handling.  
The Safety of Your Ears is in  
Your Hands  
Get the most out of your equipment by playing  
it at a safe levela level that lets the sound  
come through clearly without annoying blar-  
ing or distortion and, most importantly, with-  
out affecting your sensitive hearing. Sound  
can be deceiving. Over time, your hearing  
comfort leveladapts to higher volumes of  
sound, so what sounds normalcan actually  
be loud and harmful to your hearing. Guard  
against this by setting your equipment at a  
safe level BEFORE your hearing adapts.  
CAUTION:  
USE OF CONTROL OR ADJUSTMENT OR  
PERFORMANCE OF PROCEDURES  
OTHER THAN THOSE SPECIFIED HEREIN  
MAY RESULT IN HAZARDOUS RADIATION  
EXPOSURE.  
CAUTION:  
THE USE OF OPTICAL INSTRUMENTS  
WITH THIS PRODUCT WILL INCREASE  
EYE HAZARD.  
ESTABLISH A SAFE LEVEL:  
!
!
Set your volume control at a low setting.  
Slowly increase the sound until you can  
hear it comfortably and clearly, without dis-  
tortion.  
6
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Before you start  
02  
Operating environment  
CAUTION  
This unit should be used within the tempera-  
ture ranges shown below.  
Operating temperature range: 10 °C to +60 °C  
(14 °F to 140 °F)  
EN300328 ETC test temperature: -20 °C and  
+55 °C (-4 °F and 131 °F)  
!
Do not allow this unit to come into contact  
with liquids. Electrical shock could result.  
Also, damage to this unit, smoke, and over-  
heating could result from contact with liquids.  
Keep this manual handy for future reference.  
Always keep the volume low enough to hear  
outside sounds.  
!
!
!
!
Avoid exposure to moisture.  
If the battery is disconnected or discharged,  
any preset memory will be erased.  
After-sales service for  
Pioneer products  
Please contact the dealer or distributor from  
where you purchased this unit for after-sales  
service (including warranty conditions) or any  
other information. In case the necessary infor-  
mation is not available, please contact the  
companies listed below:  
Important (Serial number)  
The serial number is located on the bottom of  
this unit. For your own security and convenience,  
be sure to record this number on the enclosed  
warranty card.  
Please do not ship your unit to the companies  
at the addresses listed below for repair without  
advance contact.  
DVD video disc region numbers  
Only DVD video discs with compatible region  
numbers can be played on this player. You can  
find the region number of the player on the  
bottom of this unit and in this manual (refer to  
U.S.A.  
Pioneer Electronics (USA) Inc.  
CUSTOMER SUPPORT DIVISION  
P.O. Box 1760  
Long Beach, CA 90801-1760  
800-421-1404  
CANADA  
Pioneer Electronics of Canada, Inc.  
CUSTOMER SATISFACTION DEPARTMENT  
300 Allstate Parkway  
Markham, Ontario L3R 0P2  
1-877-283-5901  
About this manual  
This unit features a number of sophisticated  
functions to ensure superior reception and op-  
eration. All the functions have been designed  
for the easiest possible use, but many are not  
self-explanatory. This operation manual will  
help you benefit fully from this units potential  
and to maximize your listening enjoyment.  
We recommend that you familiarize yourself  
with the functions and their operation by read-  
ing through the manual before you begin  
using this unit. It is especially important that  
you read and observe WARNINGs and CAU-  
TIONs in this manual.  
905-479-4411  
For warranty information please see the Lim-  
ited Warranty sheet included with this unit.  
Visit our website  
Visit us at the following site:  
7
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
02  
Before you start  
Note  
1
Register your product. We will keep the details  
of your purchase on file to help you refer to  
this information in the event of an insurance  
claim such as loss or theft.  
Receive updates on the latest products and  
technologies.  
Download owners manuals, order product  
catalogues, research new products, and  
much more.  
Switch your engine ON or set the ignition switch  
to ACC ON before pressing RESET in the follow-  
ing situations:  
!
!
!
After completing connections  
When erasing all stored settings  
When resetting the unit to its initial (factory)  
settings  
2
3
4
Your feedback is important in our continual ef-  
fort to design and build the most advanced,  
consumer-focused product in the industry.  
Serial number  
Demo mode  
The feature demo automatically starts when  
you select Off for the source and continues  
while the ignition switch is set to ACC or ON.  
To cancel the feature demo, press and hold  
MUTE. Press and hold MUTE again to restart.  
Operating the feature demo while the car en-  
gine is turned off it may drain the battery  
power.  
Important  
Resetting the microprocessor  
By pressing RESET, you can reset the micro-  
processor to its initial settings without chan-  
ging the bookmark information.  
Failure to connect the red lead (ACC) of this unit  
to a terminal coupled with ignition switch on/off  
operations may lead to battery drain.  
The microprocessor must be reset in the fol-  
lowing situations:  
Adjusting the response  
positions of the touch panels  
(Touch Panel Calibration)  
If you feel that the touch panel keys on the  
screen deviate from the actual positions that  
respond to your touch, adjust the response po-  
sitions of the touch panel. Refer to Adjusting  
!
Before using this unit for the first time after  
installation  
!
!
If the unit fails to operate properly  
When strange or incorrect messages ap-  
pear on the display  
1
2
Turn the ignition switch OFF.  
Press RESET with a pen tip or other  
pointed instrument.  
Use and care of the remote  
control  
Installing the battery  
Slide the tray on the back of the remote con-  
trol out and insert the battery with the plus (+)  
and minus () poles aligned properly.  
RESET button  
8
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Before you start  
02  
!
!
The remote control may not function properly  
in direct sunlight.  
Do not let the remote control fall onto the  
floor, where it may become jammed under the  
brake or accelerator pedal.  
!
When using for the first time, pull out the  
film protruding from the tray.  
WARNING  
!
!
Keep the battery out of the reach of children.  
Should the battery be swallowed, consult a  
doctor immediately.  
Batteries (battery pack or batteries installed)  
must not be exposed to excessive heat such  
as sunshine, fire or the like.  
CAUTION  
!
!
Use one CR2025 (3 V) lithium battery.  
Remove the battery if the remote control is not  
used for a month or longer.  
!
There is a danger of explosion if the battery is  
incorrectly replaced. Replace only with the  
same or equivalent type.  
!
!
!
Do not handle the battery with metallic tools.  
Do not store the battery with metallic objects.  
If the battery leaks, wipe the remote control  
completely clean and install a new battery.  
When disposing of used batteries, comply  
with governmental regulations or environmen-  
tal public institutionsrules that apply in your  
country/area.  
!
!
Perchlorate Material special handling may  
apply.  
perchlorate. (Applicable to California, U.S.A.)”  
Using the remote control  
Point the remote control in the direction of the  
front panel to operate.  
Important  
!
Do not store the remote control in high tem-  
peratures or direct sunlight.  
9
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
03  
Whats what  
Note  
Head unit  
When the navigation system is connected, press  
MODE to switch to the navigation display. Press  
MODE and hold to turn the display off.  
Press MODE again to turn the display on.  
2
1
3
4
5
7
8
6
9
a
b
Part  
Part  
1
2
RESET  
7
8
MUTE  
MODE  
Turning the infor-  
mation display off.  
h (eject)  
MENU  
Displaying the  
menu.  
Returning to the  
normal display.  
3
4
Disc loading slot  
9
a
b
USB port  
+/(VOLUME/  
VOL)  
When connecting,  
open the USB con-  
nector lid.  
AUX input jack  
(3.5 mm stereo/  
video jack)  
Use to connect an  
auxiliary device.  
c/d (TRACK/  
SEEK)  
5
6
SRC/OFF  
CAUTION  
!
Use an optional Pioneer USB cable (CD-U50E)  
to connect the USB audio player/USB mem-  
ory as any device connected directly to the  
unit will protrude out from the unit and may  
be dangerous.  
!
!
Do not use unauthorized products.  
For details on how to operate a navigation sys-  
tem from this unit, refer to its operation man-  
ual.  
10  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Whats what  
03  
Remote control  
Part  
Operation  
Press to select the  
tuner band when  
tuner is selected as a  
source. Also used to  
cancel the control  
mode of functions.  
Press to switch be-  
tween modes when  
playing discs with  
compressed audio  
and audio data (CD-  
DA) such as CD-  
4
7 6  
j
h
c
g
BAND/ESC  
EXTRA and MIXED-  
MODE CDs.  
i
g
d
e
Press to display the  
DVD menu during  
DVD playback.  
f
5
MENU  
h
Press to return to the  
top menu during DVD  
playback.  
TOP MENU  
Press to change the  
audio language during  
DVD playback.  
Press to switch audio  
output for Video CD/  
DivX.  
Part  
Operation  
Use to select a menu  
on the DVD menu.  
c
d
Thumb pad  
AUDIO  
Press to display the  
PBC (playback con-  
trol) menu during PBC  
playback.  
RETURN  
i
Press to change the  
subtitle language dur-  
ing DVD playback.  
SUBTITLE  
Press to pause or re-  
sume playback.  
f
o
Press to change the  
viewing angle during  
DVD playback.  
ANGLE  
Press to return to the  
previous track (chap-  
ter).  
j
REAR SRC  
Not used.  
e
Press to go to the next  
track (chapter).  
p
g
Press to stop play-  
back.  
Press to select the  
next/previous disc/  
folder.  
f
a/b(FOLDER/P.CH)  
Press to recall radio  
station frequencies as-  
signed to preset tun-  
ing keys.  
11  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
04  
Basic operations  
Basic operations  
Selecting a source using the buttons  
1
Press SRC/OFF to cycle through the sources  
1
2
listed below:  
Selecting a source using the touch panel keys  
Wed 28 May  
12:45 PM  
1
Touch the source icon and then touch the desired  
source name.  
!
!
!
!
!
!
!
!
!
!
!
XM XM tuner  
Sirius SIRIUS tuner  
Radio/HD Radio Radio/Digital Radio tuner  
AV AV input  
Disc Built-in DVD player  
USB/iPod USB/iPod  
EXT1 External unit 1  
EXT2 External unit 2  
AUX AUX  
3
4
5
Rear  
View  
Radio  
TEL/Audio Bluetooth telephone/audio  
When the source icon is not displayed, it can be  
displayed by touching the screen.  
Disc  
iPod  
AUX  
Adjusting the volume  
Press +/(VOLUME/VOL) to adjust the volume.  
1
!
Touch panel keys  
Notes  
!
In this manual, iPod and iPhone will be re-  
ferred to as iPod.  
1
Displaying the source menu.  
!
The USB/iPod icon will change as follows:  
USB is displayed when a USB storage de-  
vice is connected.  
iPod is displayed when an iPod is con-  
nected.  
Switching to clock adjust-  
ment display.  
Wed 28 May  
2
3
12:45 PM  
Source icon  
USB/iPod is displayed when no device is  
connected.  
Selecting a favorite source.  
When the source icon is not  
displayed, it can be displayed  
by touching the screen.  
Radio  
!
!
When appropriately set up, the image from  
the rear view camera can be displayed auto-  
matically. For details, refer to Setting the rear  
An external unit refers to a Pioneer product,  
such as those which will be available in the fu-  
ture. Although incompatible as a source, the  
basic functions of up to two external units can  
be controlled with this unit. When two exter-  
nal units are connected, the external units are  
automatically allocated to external unit 1 or  
external unit 2.  
Rear  
View  
Switching the rear view  
image on or off.  
4
5
Turning the unit off.  
Turning the unit on using the buttons  
Press SRC/OFF to turn the unit on.  
1
Turning the unit off using the buttons  
Press SRC/OFF and hold until the unit turns off.  
1
!
If the HD Radio tuner is connected to this  
unit, tuner source is skipped.  
12  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Basic operations  
04  
Operating the scroll bar  
and the scrubber bar  
Activating the touch panel  
keys  
1
1
12  
Audio  
Fader/Balance  
Wed 28 May  
12:45 PM  
F/R 0 L/R  
0
Graphic EQ  
Loudness  
Subwoofer  
Super Bass  
1
01  
1
L+R  
Abcdeabcdeabcdeabcdeab  
High  
Off  
0
Bass Booster  
High Pass Filter  
8
12  
Off  
01:45  
-02:45  
2 1  
22  
1
1
Wed 28 May  
12:45 PM  
Return  
1
01  
1
L+R  
Abcdeabcdeabcdeabcdeab  
3
2
8
12  
1 Touch panel keys  
01:45  
-02:45  
Perform various operations by touching the  
panel.  
2 Open/close keys  
2
Control the touch panel key area by touching  
these keys.  
1 Scroll icon  
Appears when selectable items are hidden.  
2 Scrubber bar  
Turning the display to simpli-  
fied display.  
Returning to the normal dis-  
play by touching the screen  
Appears when the playback point can be spe-  
cified or set by dragging.  
1
when playing moving  
images.  
Returning to the normal dis-  
play by touching same posi-  
tion when playing audio.  
Viewing the hidden items  
1
Touch the scroll icon or drag the scrubber bar to  
view any hidden items.  
Specifying the playback point  
1
Drag the scrubber bar on the screen.  
(Not available when the scrubber bar is grayed  
out.)  
Viewing the hidden touch  
panel keys.  
2
3
Shorten the touch panel  
area.  
13  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
04  
Basic operations  
Common operations for  
menu settings/lists  
Displaying the list menu.  
Starting the search function.  
Displaying the menu.  
Displaying still images as a slide  
show when listening to another  
source.  
Viewing slide shows.  
Returning to the previous display.  
Returning to the previous list/cate-  
gory (the folder/category one level  
higher.)  
!
Press and hold MENU to display  
Picture Adjustment.  
Ejecting a disc  
%
Press h (eject).  
Setting the clock  
1
Switch to Clock Adjustment display.  
2
3
Select the item to set.  
Touch a or b to set the correct date  
and time.  
14  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Tuner  
05  
Introduction of tuner  
operations  
1
2
3
Wed 28 May  
12:45 PM  
Local  
Radio  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
87.9  
MHz  
P.ch  
2
Band:  
FM1  
87.9 MHz  
4
5
!
Touch panel keys  
Turning local seek tuning on  
and off.  
1
Switching the equalizer  
curves.  
2
3
Displaying the preset chan-  
nel list.  
Band:  
Selecting a band (FM1, FM2,  
FM3 for FM or AM).  
4
5
Recalling radio station fre-  
quencies assigned to preset  
tuning keys.  
Manual tuning (step by step) using the buttons  
Press c or d (TRACK/SEEK).  
1
Seek tuning using the buttons  
Press and hold c or d (TRACK/SEEK).  
1
Note  
Listening AM radio while an iPod is charged from  
this unit may generate noise. In this case, discon-  
nect the iPod from this unit.  
15  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
06  
Playing moving images  
such as the CD-IU50V (sold separately), you  
can enjoy the video contents of the iPod as  
an iPod source.  
Introduction of video  
playback operations  
You can view DVD/DVD-R/DVD-RW/CD/CD-R/  
CD-RW/USB/iPod.  
!
Touch panel keys  
Selecting the repeat range.  
DVD video  
1
Wed 28 May  
12:45 PM  
During playback, touch the  
point at which you want to re-  
sume playback the next time  
the disc is loaded.  
1
01  
1
L+R  
Abcdeabcdeabcdeabcdeab  
2
8
12  
Changing the screen mode.  
01:45  
-02:45  
3
4
Return  
Switching the equalizer  
curves.  
Video CD  
DivX  
Switching between audio  
languages during playback.  
Return  
5
6
7
Switching between subtitle  
languages during playback.  
iPod video  
Switching among viewing  
angles during playback.  
Wed 28 May  
12:45 PM  
S.Rtrv  
iPod  
ALL  
Songs  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Switching the audio output,  
when playing video discs re-  
corded with LPCM audio.  
2067/12345  
01:45  
-02:45  
8
Switching between stereo  
and monaural audio output,  
when playing Video CD  
discs.  
When playing a disc containing a mixture  
of various media file types  
01:45  
-02:45  
!
If an iPod with video capabilities is con-  
nected to this unit using an interface cable  
16  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Playing moving images  
06  
Starting the search function.  
Displaying iPod menus.  
Moving ahead one frame at a  
time during playback.  
Touch and hold for more  
than two seconds to slow  
down playback speed.  
Speeding up the playback  
speed in four steps during  
slow motion playback on  
DVD video/Video CD.  
9
h
Pausing playback.  
Returning to normal play-  
back during paused, slow  
motion, or frame-by-frame  
playback.  
Returning to the specified  
scene to which the DVD cur-  
rently being played has been  
preprogrammed to return.  
a
Return  
i
j
k
Displaying the DVD menu  
during DVD playback.  
b
c
Playing the video on your  
iPod in a random order.  
Returning to the top menu  
during DVD playback.  
Switching the S.Rtrv (sound  
retriever) function setting  
when playing a video on your  
iPod.  
Stopping playback.  
Stopping playback at the  
point set in Resume play-  
back.  
Touch one more time to stop  
playback completely when  
playing DivX.  
d
Conducting operation from  
your iPod and listening to it  
using your cars speakers.  
l
m
Displaying arrow keys to op-  
erate the DVD menu.  
e
f
g
Switching between media  
file types to play on DVD/CD/  
USB.  
Skipping to another title.  
Selecting a folder during  
DivX file playback.  
Speeding down the playback  
speed in four steps, during  
slow motion playback on  
Video CD.  
17  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
06  
Playing moving images  
!
Some operations may not be available while  
watching a DVD due to the programming of  
the disc. In such cases, the icon appears  
on the screen.  
To ensure proper operation, connect the dock  
connector cable from the iPod directly to this  
unit.  
Playing back videos  
1
Insert the disc into the disc loading slot with the  
label side up.  
Playback will automatically start.  
!
If you are playing a DVD or Video CD, a menu  
may appear. Refer to Operating the DVD menu on  
When the automatic playback function is on, the  
unit will skip the DVD menu and automatically  
start playback from the first chapter of the first  
!
!
!
While the iPod is connected to this unit, the  
iPod cannot be turned on or off.  
!
While an iPod is connected to this unit, PIONEER,  
OK to disconnect or (check mark) is displayed  
on the iPod.  
!
!
!
When the source icon is not displayed, it can be  
displayed by touching the screen.  
Disconnect headphones from the iPod before  
connecting it to this unit.  
Depending on the iPod model and the amount of  
data stored in the iPod, it may take some time for  
playback to begin.  
!
!
!
Use the touch panel keys to select the iPod after  
connecting it to this unit.  
No Device is displayed when disconnecting the  
iPod.  
If a message is displayed after loading a disc con-  
taining DivX VOD content, touch Play.  
Refer to Playing DivXâ VOD content on page 35.  
Ejecting a disc  
Selecting a chapter using the buttons  
1
Press c or d (TRACK/SEEK).  
Fast forwarding or reversing using the buttons  
1
Press and hold c or d (TRACK/SEEK).  
Fast forward/fast rewind may not always be possi-  
ble on some discs. In such cases, normal play-  
back will automatically resume.  
!
Notes  
!
This DVD player can play back a DivX file re-  
corded on CD-R/RW or DVD-R/RW. (Please  
see the following section for files that can be  
played back. Refer to page 78.)  
!
!
Do not insert anything other than a DVD (-R/-  
RW) or CD (-R/-RW) into the disc loading slot.  
If the bookmark function is on, DVD playback  
resumes from the selected point. For more de-  
18  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
Playing audio  
07  
Introduction of sound  
playback operations  
Switching the equalizer  
curves.  
4
You can listen to DVD-R/DVD-RW/CD/CD-R/  
CD-RW/USB/iPod sound files.  
Displaying a list of track  
titles/file names to select  
songs on a CD.  
CD  
1 2  
3 4  
5
Wed 28 May  
12:45 PM  
S.Rtrv  
ROM  
Disc  
On  
Displaying the file name  
list to select the files.  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
Abcdeabcdeabcdeabcdeab  
5
87  
125  
Displaying iPod menus.  
01:45  
-02:45  
6
7
8
9
iPod audio  
Pausing and starting  
playback.  
6
7
f
1 a b 3 4 i  
5
Wed 28 May  
12:45 PM  
S.Rtrv  
iPod  
ALL  
Songs  
Switching the text infor-  
mation to display on this  
unit when playing MP3/  
WMA/AAC files.  
Abcdeabcdeabcdeabcdea  
Abcdeabcdeabcdeabcdea  
Abcdeabcdeabcdeabcdea  
2067/12345  
01:45  
-02:45  
8
9
Selecting a folder.  
c d e  
6
h
g
You can control an iPod with this unit by using  
a cable such as the CD-IU50 (sold separately).  
Switching between  
media file types on a  
DVD/CD/USB.  
!
Touch panel keys  
Selecting the repeat  
range.  
1
Playing songs on the  
iPod in random order.  
a
b
Playing songs in random  
order.  
2
3
Changing the speed of  
audiobook playback on  
the iPod.  
Switching the S.Rtrv  
(sound retriever) function  
setting when playing  
audio.  
19  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
07  
Playing audio  
Switching to Link Search  
mode to play songs re-  
lated to the currently  
playing song on the iPod.  
Playing back sound  
1
Insert the disc into the disc loading slot with the  
label side up.  
Playback will automatically start.  
While an iPod is connected to this unit, PIONEER,  
OK to disconnect or (check mark) is displayed  
on the iPod.  
c
!
!
!
!
When the source icon is not displayed, it can be  
displayed by touching the screen.  
Disconnect headphones from the iPod before  
connecting it to this unit.  
Depending on the iPod model and the amount of  
data stored in the iPod, it may take some time for  
playback to begin.  
Playing all songs on the  
iPod in random order.  
d
e
Conducting operation  
from your iPod and listen-  
ing to it using your cars  
speakers.  
!
!
Use the touch panel keys to select the iPod after  
connecting it to this unit.  
No Device is displayed when disconnecting the  
iPod.  
Ejecting a disc  
Selecting a track using the buttons  
!
Text information  
1
Press c or d (TRACK/SEEK).  
Displaying the Songs list  
on the iPod.  
Fast forwarding or reversing using the buttons  
1
Press and hold c or d (TRACK/SEEK).  
f
Notes  
!
!
When playing back files recorded as VBR  
Displaying the Artists list  
on the iPod.  
(variable bit rate) files, the play time will not be  
correctly displayed if fast forward or reverse  
operations are used.  
To ensure proper operation, connect the dock  
connector cable from the iPod directly to this  
unit.  
While the iPod is connected to this unit, the  
iPod cannot be turned on or off.  
If the characters recorded on the disc are not  
compatible with this unit, those characters  
will not be displayed.  
g
Displaying the Albums  
list on the iPod.  
h
!
!
!
Artwork display  
Starting Album Link Search on your iPod  
when you touch the artwork display.  
!
Text information may not be correctly dis-  
played depending on the recorded environ-  
ment.  
i
!
!
Disconnect the USB portable audio player/  
USB memory when you are done using it.  
When you select Clock on Selecting the back-  
ground display on page 55, the artwork is not  
displayed.  
20  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
Playing still images  
08  
Introduction of still image  
playback operations  
You can view still images saved in CD-R/CD-  
RW/USB.  
Displaying the file name  
list to select the files.  
4
Starting or pausing the sli-  
deshow.  
CD  
5
6
1 2 3  
4
Wed 28 May  
12:45 PM  
Photo  
Rotating the displayed pic-  
ture 90° clockwise.  
Off  
Full  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Capturing an image in  
JPEG files.  
7
8
2
2
Capture  
5
6 7  
8
Selecting a folder.  
When playing a disc containing a mixture  
of various media file types  
01:45  
-02:45  
Switching between media  
file types.  
9
When loading a CD-R/CD-RW/USB containing  
JPEG picture files, this unit starts a slideshow  
from the first folder/picture on the disc/device.  
The player displays the pictures in each folder  
on the CD-R/CD-RW in alphabetical order by  
file name.  
Playing still images  
1
Insert the disc into the disc loading slot with the  
label side up.  
Playback will automatically start.  
When the source icon is not displayed, it can be  
displayed by touching the screen.  
!
The table below shows the controls for viewing  
a slideshow.  
Ejecting a disc.  
!
Touch panel keys  
Touch any of the following touch panel keys  
to select the function to be adjusted.  
Selecting a file using the buttons  
1
Press c or d (TRACK/SEEK).  
Fast file searching  
Selecting the repeat range.  
1
Press and hold c or d (TRACK/SEEK).  
1
2
!
You can search 10 JPEG files at a time.  
Playing files in a random  
order.  
Notes  
This unit can play back a JPEG file recorded  
!
on CD-R/CD-RW/USB storage device. (Please  
see the following section for files that can be  
played back. Refer to JPEG picture files on  
Changing the screen  
mode.  
3
21  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
08  
Playing still images  
!
Files are played back in file number order and  
folders are skipped if they contain no files. (If  
folder 01 (ROOT) contains no files, playback  
commences with folder 02.)  
5
Selecting a file.  
Starting or pausing the sli-  
deshow.  
6
7
Introduction of still image  
playback as a slideshow  
operations  
Rotating the displayed pic-  
ture 90° clockwise.  
You can view still images saved in CD-R/CD-  
RW/USB as a slideshow when listening to an-  
other source.  
Capturing an image in  
JPEG files.  
8
1 2 3  
4
5
Off  
1
Start slideshow when listening to an-  
Full  
other source.  
Displaying still images as a slide  
show.  
Capture  
7 8  
6
2
Select the device containing the files  
The table below shows the controls for viewing  
a slideshow.  
that you want to display.  
!
!
Disc Built-in DVD player  
USB USB  
To cancel searching, touch Cancel.  
!
Touch panel keys  
Touch any of the following touch panel keys  
to select the function to be adjusted.  
#
Note  
Selecting the repeat range.  
When the disc or USB source is selected, this  
unit cannot view still images on disc/USB as a  
slideshow.  
1
2
Playing files in a random  
order.  
Changing the screen  
mode.  
3
4
Selecting a folder.  
22  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
XM/SIRIUS tuner  
09  
When the SIRIUS tuner is used together  
with this unit, some operations differ  
slightly from those described in the SIRIUS  
operation manual. This manual provides in-  
formation on these points. For all other in-  
formation on using the SIRIUS tuner,  
please refer to the SIRIUS operation man-  
ual.  
Introduction of XM/SIRIUS  
tuner operations  
SIRIUS tuner  
1 2 3  
4
5
Mode  
Wed 28 may  
12:45 PM  
Memo Team  
SIRIUS  
All CH  
Off  
Off  
!
!
With this unit, you can operate one addi-  
tional function: XM/SIRIUS channel direct  
selection. Refer to Selecting an XM/SIRIUS  
Abcdeabcdeabcde  
2
CH183  
P.CH  
SBIRanIdU: S  
CH183  
6
7
Touch panel keys  
Instant  
Replay  
Memo Game Team  
Info Setting  
Memo  
Edit  
Selecting a channel by  
number or category.  
Mode  
All CH  
8
9 a b c d  
1
2
Mode  
Category  
XM tuner  
1
4
5
Tuning the MyMix func-  
tion on or off for the SIR-  
IUS tuner.  
Memo  
On  
Mode  
Wed 28 may  
12:45 PM  
XM  
XM  
All CH  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Abcdeabcdeabcde  
Memo  
CH183  
Off  
P.ch  
2
Band:  
XM  
CH183  
Turning the Game Alert  
on or off for the SIRIUS  
tuner.  
Team  
On  
6
3
4
Team  
Memo  
Edit  
Memo  
Off  
8
a b  
Switching the equalizer  
curves.  
!
!
You can use this unit to control an XM sa-  
tellite digital tuner (GEX-P920XM), which is  
sold separately.  
For details concerning operation, refer to  
the XM tuners operation manuals. This  
section provides information on XM opera-  
tions with this unit which differs from that  
described in the XM tuners operation man-  
ual.  
You can use this unit to control a SIRIUS  
Satellite Radio tuner, which is sold sepa-  
rately.  
23  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
09  
XM/SIRIUS tuner  
Displaying the preset  
channel list.  
Switching to memo edit  
mode.  
Selecting a channel di-  
rectly.  
Selecting a channel from  
the XM channel list.  
Memo  
Edit  
b
5
6
8
Displaying information  
on games for the SIRIUS  
tuner.  
Game  
Info  
c
d
Selecting a band (XM1,  
XM2 or XM3) for XM  
tuner.  
Selecting a band (SIR-  
IUS1, SIRIUS2 or SIR-  
IUS3) for the SIRIUS  
tuner.  
Band:  
Selecting teams for  
game alert on the SIRIUS  
tuner.  
Team  
Setting  
Recalling radio station  
frequencies assigned to  
preset tuning keys.  
Selecting the channel ca-  
tegory when selecting  
Mode Category.  
!
SIRIUS tuner information  
Switching the SIRIUS information.  
7
Touch and hold for more than two seconds  
to scroll the text.  
Manual tuning (step by step) using the buttons  
Press c or d (TRACK/SEEK).  
1
Seek tuning using the buttons  
Press and hold c or d (TRACK/SEEK).  
Selecting a track, fast for-  
warding/reversing or  
pausing/playing for the  
SIRIUS tuner.  
1
Instant  
Replay  
Note  
9
a
You can also perform tuning from a desired chan-  
nel category. (Refer to Selecting a XM/SIRIUS  
Storing the song title and  
artist name.  
Refer to Making the  
Memo  
24  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
HD Radioä tuner  
10  
Introduction of HD Radioä  
tuner operations  
Band:  
Selecting a band (FM1, FM2,  
FM3 for FM or AM).  
6
8
2 3  
4
5
1
Recalling radio station fre-  
quencies assigned to preset  
tuning keys.  
Blending  
Seek  
Digital  
Radio  
Wed 28 may  
12:45 PM  
Local  
D/AAuto  
All  
Abcdeabcdeabcde  
2
87.9  
MHz  
!
Digital Radio tuner information  
P.CH  
Band:  
FM1  
87.9 MHz  
Switching the digital radio tuner informa-  
tion.  
7
6
7
8
Manual tuning (step by step) using the buttons  
Press c or d (TRACK/SEEK).  
This HD Radio Ready receiver is ready to re-  
ceive HD Radio broadcasts when connected  
to the HD Radio tuner (e.g. GEX-P20HD), sold  
separately.  
1
Seek tuning using the buttons  
Press and hold c or d (TRACK/SEEK).  
1
For details concerning operation, refer to the  
HD Radio tuners operation manual.  
!
Touch panel keys  
Turning local seek tuning on  
or off.  
1
Seek  
All  
Switching between Digital  
broadcasting station seek  
and normal seek.  
2
3
Seek  
HD  
Blending  
D/AAuto  
Blending  
Analog  
Switching to the analog  
broadcast of the same fre-  
quency.  
Switching the equalizer  
curves.  
4
5
Displaying the preset chan-  
nel list.  
25  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
11  
Using Bluetooth wireless technology  
Introduction of Bluetooth  
Switching the equalizer  
curves.  
1
telephone operations  
During a call  
Accepting an incoming call.  
Making a phone call, when  
selecting a phone number  
from the dialed and received  
call history.  
2
3
1
Wed 28 May  
12:45 PM  
2
3
TEL  
Abcdeabc  
Ending a call.  
Rejecting an incoming call.  
Canceling call waiting.  
Text  
Scroll  
REG  
Displaying the received/  
missed call history.  
Selecting a phone number  
from the call history.  
4 5 6 7 8 9  
4
Except during a call  
Text  
REG  
Scroll  
a
Displaying the dialed call his-  
tory.  
Selecting a phone number  
from the call history.  
When you connect a Bluetooth adapter (e.g.  
CD-BTB200)(sold separately) to AVH-  
P2300DVD, you can control Bluetooth tele-  
phone.  
5
But the available features are limited.  
Scrolling the phone number.  
Touch and hold for more  
than two seconds to activate  
connection mode on this  
unit and establish a Blue-  
tooth wireless connection  
from your phone.  
Important  
!
!
In some countries, CD-BTB200 is not sold on  
the market.  
Text  
Scroll  
6
Since this unit is on standby to connect with  
your cellular phone via Bluetooth wireless  
technology, using it without the engine run-  
ning can drain the battery power.  
Advanced operations that require attention  
such as dialing numbers on the monitor, etc.,  
are prohibited while driving. Park your vehicle  
in a safe place when using these advanced  
operations.  
!
Registering connected cellu-  
lar phone to take full advan-  
tage of the features available  
with Bluetooth wireless tech-  
nology.  
Touch and hold for more  
than two seconds to termi-  
nate the Bluetooth wireless  
connection.  
!
!
Operations available may be limited depend-  
ing on the cellular phone connected to this  
unit.  
7
Touch panel keys  
26  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Using Bluetooth wireless technology  
11  
Turning automatic answering  
on or off.  
1
Connection  
First, you need to connect a Bluetooth telephone  
to this unit.  
Touch and hold for more  
than two seconds to connect  
to a Bluetooth telephone  
automatically.  
For detailed instructions on connecting your  
phone to this unit via Bluetooth wireless technol-  
ogy, see following section. Using a cellular phone  
Volume adjustment  
8
2
Adjust the earpiece volume of your cellular phone  
to your preference.  
Turning the ring tone for in-  
coming calls on or off.  
Touch and hold for more  
than two seconds to display  
the Bluetooth device address  
and the device name.  
!
!
!
The volume of the callers voice and ring tone  
may vary depending on the type of cellular  
phone.  
If there is a large volume difference between  
the ring tone and callers voice, the overall vo-  
lume level may become unstable.  
Make sure to adjust the volume to a proper  
level before disconnecting the cellular phone  
from the unit. If the volume is muted (zero  
level) on your cellular phone, the volume level  
of your cellular phone remains muted even  
after the cellular phone is disconnected.  
9
Switching between Bluetooth  
telephone and Bluetooth  
audio.  
Touch and hold for more  
than two seconds to start  
voice recognition.  
a
Bluetooth audio operations  
When you connect a Bluetooth adapter (e.g.  
CD-BTB200)(sold separately) to AVH-  
P2300DVD, you can control Bluetooth audio.  
Setting up for hands-free phoning  
Before you can use the hands-free phoning  
function you must set up the unit for use with  
your cellular phone. This entails establishing a  
Bluetooth wireless connection between this  
unit and your phone, registering your phone  
with this unit, and adjusting the volume level.  
Important  
!
Depending on the Bluetooth audio player con-  
nected to this unit, the available operations  
will be limited to the following two levels:  
A2DP profile (Advanced Audio Distribution  
Profile): You can only playback songs on  
your audio player.  
AVRCP profile (Audio/Video Remote Con-  
trol Profile): You can perform playback,  
pause playback, select songs, etc.  
!
Since there are a number of Bluetooth audio  
players available on the market, available op-  
erations will vary extensively. When operating  
your player with this unit, refer to the instruc-  
tion manual that came with your Bluetooth  
audio player as well as this manual.  
27  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
11  
Using Bluetooth wireless technology  
!
!
Information related to a song (such as the  
elapsed playing time, song title, song index,  
etc.) cannot be displayed on this unit.  
Setting the action for c and d  
icons.  
As the signal from your cellular phone may  
cause noise, avoid using it when you are lis-  
tening to songs on your Bluetooth audio  
player.  
Auto  
Switching the equalizer curves.  
!
When a call is in progress on the cellular  
phone connected to this unit via Bluetooth  
wireless technology, the sound of the Blue-  
tooth audio player connected to this unit is  
Setting up for Bluetooth audio  
muted.  
Before you can use the Bluetooth audio func-  
tion you must set up the unit for use with your  
Bluetooth audio player. This entails establish-  
ing a Bluetooth wireless connection between  
this unit and your Bluetooth audio player, and  
pairing your Bluetooth audio player with this  
unit.  
!
!
When the Bluetooth audio player is in use,  
you cannot connect to a Bluetooth telephone  
automatically.  
Playback continues even if you switch from  
your Bluetooth audio player to another source  
while listening to a song.  
!
Touch panel keys  
1
Connection  
First, you need to connect a Bluetooth audio to  
this unit.  
For detailed instructions on connecting your  
Bluetooth audio to this unit via Bluetooth wireless  
Switching between Bluetooth tele-  
phone and Bluetooth audio.  
Skipping back or forward to an-  
other track when Auto is set for  
the auto/manual setting.  
Performing fast forward or rewind  
when Manual is set for the auto/  
manual setting.  
Pausing a song.  
Touch and hold for more than two  
seconds to activate connection  
mode on this unit and establish a  
Bluetooth wireless connection  
from your player.  
F1  
Playback starts.  
Touch and hold for more than two  
seconds to terminate the Blue-  
tooth wireless connection.  
F2  
28  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
Detailed instructions  
12  
1
Display the preset screen.  
Storing and recalling stations  
You can easily store up to six stations for each  
band as presets.  
!
!
Six stations for each band can be stored in  
memory.  
The preset screen appears in the display.  
Channels are stored and recalled on a  
broadcast station basis. This means that if  
the broadcast station you stored has been  
assigned to a different channel by SIRIUS,  
you can still recall the same broadcast sta-  
tion (though a different channel number  
may appear in the display).  
2
Touch BSM to turn BSM on.  
The six strongest broadcast frequencies will  
be stored under preset tuning keys in order of  
their signal strength.  
#
To cancel the storage process, touch  
Cancel.  
1
Display the preset screen.  
Tuning in to strong signals  
Local seek tuning lets you tune in to only  
those radio stations with sufficiently strong  
signals for good reception.  
FM: off —  
The preset screen appears in the display.  
AM: off —  
2
Touch and hold one of the preset tun-  
The highest level setting allows reception of  
only the strongest stations, while lower levels  
allow the reception of weaker stations.  
ing keys to store the selected frequency in  
the memory.  
The selected radio station frequency has been  
stored in the memory.  
Tuning in to strong HD  
Radio signals  
Local seek tuning lets you tune in to only  
those radio stations with sufficiently strong  
signals for good reception.  
3
Touch one of the preset tuning keys to  
select the desired station.  
You can also use a and b to recall stations  
#
assigned to preset tuning keys Preset1 to  
Preset6 when the Mode All CH mode is se-  
lected.  
(Function of SIRIUS tuner)  
1
Start local seek tuning  
Storing the strongest stations  
2
Touch On on Local to turn on.  
BSM (best stations memory) automatically  
stores the six strongest stations in the order of  
their signal strength.  
Storing broadcast frequencies with BSM may  
replace broadcast frequencies you have saved  
using the preset tuning keys.  
#
To turn off, touch Off.  
3
Touch c or d on Level to select the de-  
sired level.  
#
#
Level1Level2Level3Level4  
The highest level setting allows reception of  
only the strongest stations, while lower levels  
allow the reception of weaker stations.  
29  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
Switching the media file type  
Returning to the normal DVD video  
display.  
When playing a disc containing a mixture of  
various media file types, such as DivX and  
MP3, you can switch between media file types  
to play.  
Displaying arrow keys.  
Audio data (CD-DA) and JPEG picture files on  
DVD-R/RW/ROM cannot be played back on  
this unit.  
#
Ways to display the menu will differ depend-  
ing on the disc.  
Depending on the contents of the DVD disc,  
#
CD (audio data (CD-DA))Music/ROM (com-  
pressed audio)Video (DivX video files)—  
Photo (JPEG picture files)  
this function may not work properly. In such  
cases, use the touch panel keys to operate the  
DVD menu.  
Operating the DVD menu  
(Function for DVD video)  
Some DVDs allow you to make a selection  
from the disc contents using a menu.  
Operating this units iPod  
function from your iPod  
You can listen to the sound from your iPod ap-  
plications using your car's speakers, when  
App Mode is selected.  
This function is not compatible with the follow-  
ing iPod models.  
Using the arrow keys  
1
Display arrow keys to operate the DVD  
!
!
iPod nano 1st generation  
iPod 5th generation  
menu.  
Refer to Playing moving images on page 16.  
APP mode is compatible with the following  
iPod models.  
2
Select the desired menu item.  
!
!
!
!
!
iPhone 4 (software version 4.1 or later)  
iPhone 3GS (software version 4.1 or later)  
iPhone 3G (software version 4.1 or later)  
iPhone (software version 3.1.3 or later)  
iPod touch 4th generation (software version  
4.1 or later)  
Selecting the desired menu item.  
!
!
!
iPod touch 3rd generation (software version  
4.0 or later)  
iPod touch 2nd generation (software ver-  
sion 4.0 or later)  
iPod touch 1st generation (software version  
3.1.3 or later)  
Starting playback from the se-  
lected menu item.  
1
Switch the control mode to App Mode.  
Operating the DVD menu by di-  
rectly touching the menu item.  
#
When operating the DVD menu by directly  
touching the menu item, touch the icon to oper-  
ate.  
2
Operate the connected iPod to select a  
video/song and play.  
30  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
Note  
!
!
One Repeat just the current video/song/  
track  
All Repeat all videos/songs in the se-  
lected list on the iPod and all files on the  
USB  
The following functions are still accessible from  
the unit even if the control mode is set to  
App Mode.  
However, the operation will depend on your appli-  
cations.  
!
!
!
This function cannot be operated during  
Video CD playback featuring PBC (playback  
control).  
If you perform chapter search, fast forward/  
reverse, frame-by-frame playback or slow  
motion playback, the repeat play will stop.  
When playing discs with compressed audio  
and audio data (CD-DA), playback is re-  
peated within the type of data currently  
playing even if Disc is selected.  
!
!
!
!
Pausing  
Fast forwarding/reversing  
Tracking up/down  
Moving to a chapter up/down  
Random play (shuffle)  
iPod-videos/songs can be played back in ran-  
dom order.  
!
If you select another folder during repeat  
play, the repeat play range changes to Disc.  
If you select USB source, the repeat play  
range changes to All.  
If you perform track search or fast forward/  
reverse during File, the repeat play range  
changes to Folder.  
If you perform title/chapter search or fast  
forward/reverse during Chapter, the repeat  
play range changes to Disc.  
If you perform track search or fast forward/  
reverse during Track, the repeat play range  
changes to Disc.  
!
!
!
!
!
!
Songs Play back videos/songs in the se-  
lected list in random order.  
Albums Play back videos/songs from a  
randomly selected album in order.  
Folder Play back songs/tracks in the se-  
lected folder in random order.  
Disc Play back songs/tracks in the se-  
lected disc in random order.  
On Play back files in random order within  
the repeat range, Folder and Disc.  
Off Cancel random play.  
!
!
!
!
When Folder is selected, it is not possible  
to play back a subfolder of that folder.  
Playing all songs in random  
order (shuffle all)  
(Function for iPod)  
This method plays all songs on the iPod  
randomly.  
Playing videos from your iPod  
(Function for iPod)  
Videos can be played on this unit if an iPod  
with video capabilities is connected.  
!
!
This unit can play back Movies, Music vi-  
deos, Video Podcastand TV show”  
which are downloaded from the iTunes  
store.  
Before you display the video screen, be  
sure to change the video setting on the  
iPod so that the iPod can output the video  
to an external device.  
Repeating playback  
!
!
!
!
!
!
Disc Play through the current disc  
Chapter Repeat the current chapter  
Title Repeat the current title  
Track Repeat the current track  
File Repeat the current file  
Folder Repeat the current folder  
31  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
!
Audiobooks (audiobooks)  
1
Display the iPod menus.  
Refer to Playing moving images on page 16.  
3
Touch the title of the list that you want  
to play.  
2
Switch to iPod video mode.  
Repeat this operation until you find the de-  
sired video/music.  
Switching to iPod video mode.  
Video  
4
Start playback of the selected list.  
3
#
Play the video from the iPod.  
If you want to switch to iPod music mode,  
Starting playback of the selected list.  
touch the icon.  
Switching to iPod music mode.  
Searching the list by alphabet  
Music  
(Function for iPod)  
1
Select a category.  
Browsing for a video/music  
on the iPod  
2
Switch to alphabet search mode.  
(Function for iPod)  
To make operating and searching easy, opera-  
tions to control an iPod with this unit are de-  
signed to be as similar to the iPod as possible.  
Switching to alphabet search mode.  
Alphabet search mode is displayed.  
Touch the first letter of the title of the  
video/song you are looking for.  
While searching, touch panel key operation is  
not available.  
3
Searching for a video/music by  
category  
1
Display the iPod menus.  
Refer to Playing moving images on page 16.  
Refer to Playing audio on page 19.  
#
To refine the search with a different letter,  
touch Cancel.  
2
Touch one of the categories in which  
4
Touch the title of the list that you want  
you want to search for a video/music.  
to play.  
!
!
!
!
!
!
!
!
!
!
!
!
Video Playlists (video playlists)  
Movies (movies)  
Music Videos (music videos)  
Video Podcasts (video podcasts)  
TV Shows (TV shows)  
Playlists (playlists)  
Artists (artists)  
Albums (albums)  
Songs (songs)  
Podcasts (podcasts)  
Genres (genres)  
Repeat this operation until you find the de-  
sired song/video.  
5
Start playback of the selected list.  
Starting playback of the selected list.  
Composers (composers)  
32  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
!
This function cannot be operated during  
some DVD videos or Video CD playback  
featuring PBC (playback control).  
Resume playback (Bookmark)  
(Function for DVD video)  
By using the Bookmark function, you can re-  
sume playback from a selected scene the next  
time the disc is loaded.  
1
Start the search function.  
Refer to Playing moving images on page 16.  
The selected scene will be bookmarked so that  
playback resumes from that point next time.  
2
Touch the desired search option (e.g.,  
Chapter).  
!
To clear the bookmark on a disc, touch and  
hold the button during playback.  
The oldest bookmark is replaced by the  
new one.  
3
ber.  
#
Touch 0 to 9 to input the desired num-  
!
To cancel the entered numbers, touch C.  
4
Start playback from the selected part.  
Frame-by-frame playback  
(Function for DVD video/video CD/DivX file)  
Registering the numbers and start-  
ing playback.  
Note  
Note  
Images during frame-by-frame playback may be  
unclear for some discs.  
With discs featuring a menu, you can also use  
the DVD menu to make your selection.  
Refer to Playing moving images on page 16.  
Slow motion playback  
Notes  
Changing audio language  
during playback (Multi-audio)  
With DVDs/DivX files that provides audio play-  
back in different languages and different  
audio systems such as Dolby Digital, you can  
switch between languages/audio systems dur-  
ing playback.  
!
!
!
There is no sound during slow motion play-  
back.  
Images during slow motion playback may be  
unclear for some discs.  
Reverse slow motion playback is not  
available.  
Notes  
Searching for the part you  
want to play  
You can use the search function to find the  
part you want to play.  
For DVD videos, you can select Title (title),  
Chapter (chapter) or 10key (numeric keypad).  
For video CDs, you can select Track (track) or  
10key (numeric keypad).  
!
!
!
!
With some DVDs, switching between lan-  
guages/audio systems may only be possible  
using a menu display.  
You can also switch between languages/audio  
systems using Video Setup menu. For details,  
Depending on the setting, the video may not  
be played back with the audio system used to  
record the DVD.  
!
Chapter search is not available when disc  
playback is stopped.  
You will return to normal playback if you  
change the Audio during fast forward/fast re-  
wind, pause or slow motion playback.  
33  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
Changing the subtitle  
language during playback  
(Multi-subtitle)  
With DVDs/DivX files featuring multi-subtitle  
recordings, you can switch between subtitle  
languages during playback.  
Selecting audio output  
When playing DVD video discs recorded with  
LPCM audio, you can switch the audio output.  
When playing video CDs, you can switch be-  
tween stereo and monaural audio output.  
!
This function is not available when disc  
playback is stopped.  
Notes  
!
!
!
!
L+R left and right  
Left left  
Right right  
!
With some DVDs, switching between subtitle  
languages may only be possible using a menu  
display.  
Mix mixing left and right  
!
You can also switch between subtitle lan-  
guages using Video Setup menu. For details,  
You may not be able to select or use this func-  
tion depending on the disc and the playback  
location.  
!
You will return to normal playback if you  
change the Subtitle during fast forward/fast  
rewind, pause or slow motion playback.  
PBC playback  
(Function for Video CDs)  
During playback of Video CDs featuring PBC  
(Playback Control), PBC ON is displayed.  
Changing the viewing angle  
during playback (Multi-angle)  
With DVDs featuring multi-angle (scenes shot  
from multiple angles) recordings, you can  
switch among viewing angles during play-  
back.  
1
Start the search function.  
Refer to Playing moving images on page 16.  
2
Touch 10key to display the numeric  
keypad.  
!
During playback of a scene shot from mul-  
tiple angles, the angle icon is displayed.  
Use the Video Setup menu to turn the  
angle icon display on or off. For details,  
3
Touch 0 to 9 corresponding to a menu  
number.  
4
Start playback from the selected part.  
Registering the numbers and start-  
ing playback.  
Note  
You will return to normal playback if you change  
the viewing angle during fast forward/fast rewind,  
pause or slow motion playback.  
Notes  
!
You can display the menu by touching Return  
during PBC playback. For details, refer to the  
instructions provided with the disc.  
PBC playback of a Video CD cannot be can-  
celed.  
!
!
Return to the specified scene  
(Function for DVD video)  
During playback of Video CDs featuring PBC  
(Playback Control), you cannot select the re-  
peat play range or use the search function.  
This function cannot be used if a specified  
scene has not been preprogrammed on the  
DVD disc.  
34  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
Selecting tracks from the  
track title list  
You can select tracks to playback using the  
track title list which is a list of the tracks re-  
corded on a disc.  
Changing audiobook speed  
(Function for iPod)  
!
Playback at a speed faster than  
normal  
!
!
Playback at normal speed  
Playback at a speed slower than nor-  
1
Display the track title list.  
mal  
Refer to Playing audio on page 19.  
2
Touch your favorite track title.  
Displaying lists related to  
the currently playing song  
(Link Search)  
Playback begins.  
Selecting files from the file  
name list  
(Function for compressed audio/DivX/JPEG)  
File name list is a list of file names (or folder  
names) from which you can select a file (or  
folder) to play back.  
(Function for iPod)  
1
Start Link Search.  
2
Touch one of the categories in which  
you want to play.  
1
Display the file (or folder) name list.  
!
!
!
Artist Displays an album list of the artist  
currently being played.  
Album Displays a song list from the  
album currently being played.  
Genre Displays an album list from the  
genre currently being played.  
Refer to Playing audio on page 19.  
2
Touch your favorite file (or folder)  
name.  
#
#
To cancel searching, touch Cancel.  
When you have selected a folder, a list of the  
names of the files (or the folders) in it can be  
viewed. Repeat this operation to select the de-  
sired file name.  
3
Touch the title of the list that you want  
to play.  
#
If folder 01 (ROOT) contains no files, playback  
4 Start playback of the selected list.  
commences with folder 02.  
Starting playback of the selected list.  
3
Start playback of the selected list.  
Starting playback of the selected list.  
â
Playing DivX VOD content  
Some DivX VOD (video on demand) content  
may only be playable a fixed number of times.  
When you load a disc containing this type of  
content, the remaining number of times it can  
be played is shown on-screen. You can then  
decide whether or not to play the disc.  
Using sound retriever  
Automatically enhances compressed audio  
and restores rich sound.  
Off —  
!
is more effective than  
.
35  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
!
!
If there is no limit to the number of times  
the DivX VOD content can be viewed, then  
you may load the disc into your player and  
play the content as often as you like, and  
no message will be displayed.  
You can confirm the number of times that  
the content can be played by checking the  
message displayed after This DivX rental  
has used.  
3
When Do you save this image? is dis-  
played, touch Yes.  
While storing the image to this unit, Saving  
the image Don't switch off the battery. is  
displayed. When the process is finished,  
Image saved is displayed.  
#
To cancel the storage process, touch No.  
Important  
!
In order to play DivX VOD contents on this  
unit, you first need to register the unit with  
your DivX VOD contents provider. For details  
on your registration code, refer to Displaying  
the DivXâ VOD registration code on page 51.  
DivX VOD content is protected by a DRM (Di-  
gital Rights Management) system. This re-  
stricts playback of content to specific,  
registered devices.  
Changing the wide screen  
mode  
You can select a desired mode for enlarging a  
4:3 picture to a 16:9 picture.  
!
1
Display the screen mode.  
%
If a message is displayed after loading  
a disc containing DivX VOD content, touch  
Play.  
Playback of the DivX VOD content will start.  
#
#
To skip to the next file, touch Next Play.  
If you do not want to play the DivX VOD con-  
2
Touch the desired wide mode setting.  
tent, touch Stop.  
Full (full screen)  
The 4:3 picture is enlarged in the horizontal direc-  
tion only, giving you a 4:3 TV picture (normal pic-  
ture) without any omissions.  
Capture an image in JPEG files  
You can capture image data and use it as wall-  
paper. Images can be stored and recalled ea-  
sily in this unit.  
Just (just)  
The picture is enlarged slightly at the center and  
the amount of enlargement increases horizontally  
toward the edges of the screen, enabling you to  
enjoy a 4:3 picture without sensing any disparity  
even when viewing on a wide screen.  
!
Only one image can be stored on this unit.  
Old image is overwritten with the new one.  
1
Pause the slideshow when the desired  
image is displayed.  
Cinema (cinema)  
The picture is enlarged by the same proportion as  
Full or Zoom in the horizontal direction and by  
an intermediate proportion between Full and  
Zoom in the vertical direction; ideal for a cinema-  
sized picture (wide screen picture) where cap-  
tions lie outside the picture.  
2
Capture the image.  
36  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
Zoom (zoom)  
1
Select channel category selection  
mode.  
The 4:3 picture is enlarged in the same proportion  
both vertically and horizontally; ideal for a cinema  
sized picture (wide screen picture).  
Mode All CH (channel number select setting)  
Mode Category (channel category select  
setting)  
Normal (normal)  
The 4:3 picture is displayed as it is, giving you no  
sense of disparity since its proportions are the  
same as that of the normal picture.  
2
Touch a or b to select the desired chan-  
nel category.  
Notes  
3
Touch c or d on the buttons to select  
!
!
You cannot operate this function while driving.  
Different settings can be stored for each video  
source.  
the desired channel in the selected channel  
category.  
!
!
When a video is viewed in a wide screen mode  
that does not match its original aspect ratio, it  
may appear different.  
Remember that using the wide mode feature  
of this system for commercial or public view-  
ing purposes may constitute an infringement  
on the authors rights protected by the Copy-  
right Law.  
Selecting a channel from the  
XM channel list display  
The list content can be switched so you can  
search for the track you want to listen to not  
only by the channel name but also by the artist  
name or song title.  
!
!
This function is available for GEX-P920XM.  
The channel list shows all the channels  
during Mode All CH mode, and the chan-  
nels included in the selected category dur-  
ing Mode Category mode.  
!
The video image will appear coarser when  
viewed in Cinema or Zoom mode.  
Switching the XM/SIRIUS  
channel selection mode  
You have two methods for selecting a channel:  
by number and by category. When selecting  
by number, channels in any category can be  
selected. Select by category to narrow your  
search down to only channels in a particular  
category.  
1
Display the preset channel list.  
2
Switch the channel list mode.  
Switching the channel list mode to  
the channel name or the artist  
name/song title.  
Mode All CH (channel number select setting)  
Mode Category (channel category select  
setting)  
3
Touch the desired channel that you  
want to listen to.  
Selecting a XM/SIRIUS channel  
from a channel category  
Channels are organized into various program  
categories, e.g. Rock, Classic, Jazz while lis-  
tening to a XM/SIRIUS station. You can specify  
channels by selecting the desired category.  
Selecting an XM/SIRIUS  
channel directly  
You can select an XM/SIRIUS channel directly  
by entering the desired channel number.  
37  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
1
Display the preset channel list.  
The song title and artist name of the song you  
are listening to are stored, and a confirmation  
message appears.  
#
To delete a song from the MyMix playlist, refer  
2
Switch to direct input display.  
Switching to direct input display.  
#
(XM tuner)  
The song title and artist name of up to 12 tracks  
can be stored. Old tracks will be overwritten  
when saving more than 12 tracks.  
3
Touch 0 to 9 to input the desired chan-  
nel number.  
#
To cancel the input numbers, touch C.  
#
(SIRIUS tuner)  
The song title and artist name of up to 10 tracks  
can be stored.  
4
Select the XM/SIRIUS channel of the en-  
tered number.  
The XM/SIRIUS channel of the entered num-  
ber is selected.  
#
You cannot store the song title or the artist  
name when “– – – – – – – –” is displayed for the  
title information.  
#
You cannot store song titles or artist names  
from channel 000.  
Stored titles may not be displayed correctly.  
Selecting the XM/SIRIUS channel of  
the entered number.  
#
Using the MyMix function  
The MyMix function allows you to make a  
MyMix song playlist. When a song in the  
MyMix playlist is being broadcast on a station  
other than the one you are listening to, you  
will be alerted, and you can tune in to the  
other station to listen to that song.  
!
This function is available for GEX-P920XM/  
SIRIUS tuner.  
!
The track itself is NOT downloaded. Only  
the song title and artist name are stored.  
Making the MyMix playlist  
You can add a song that is being broadcast to  
the MyMix playlist. When it is added, the song  
title and its artist name are stored to this unit.  
The MyMix function will start when you listen  
to a song that matches a song title and its ar-  
tist name in the MyMix playlist.  
%
Store the song title and artist name.  
38  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
MyMix playlist and then change each alert set-  
ting. Set the alert to on to receive an alert  
when the song is broadcast, or set it to off to  
stop the alert for that song.  
When a song in the MyMix  
playlist is broadcast  
(XM tuner)  
As soon as a song in the MyMix playlist starts  
being broadcast on a different station, a mes-  
sage is displayed. Touch Yes to switch to that  
station, and you can listen to that song.  
(SIRIUS tuner)  
1
Switch to memo edit mode.  
The MyMix playlist is displayed.  
As soon as a stored song starts being broad-  
cast on a different station, a song alert is dis-  
played.  
2
Select the song title for which you  
want to turn the alert on or off.  
(XM tuner)  
The check mark is removed, and the alert for  
that song is off.  
Switching to the other station to lis-  
ten to that track.  
(SIRIUS tuner)  
Not tuning in to the other station.  
Selecting the song title for which  
you want to turn the alert off.  
!
!
(XM tuner)  
If you would rather not to tune in to the  
other station, touch No.  
If an alert for a song in the MyMix playlist is  
set to off, no alert will be provided even  
when the song is broadcast. Refer to Set-  
If the stored title and the title of the song  
being broadcast differ, no alert will be pro-  
vided even if they are the same song.  
3
Turn the alert on or off.  
(SIRIUS tuner)  
!
Turning the alert on or off.  
Deleting a song from the  
MyMix playlist for XM tuner  
You can delete each song in the MyMix play-  
list.  
Turning the MyMix function on  
or off  
You can turn the MyMix function off and stop  
the alerts for all the songs in the MyMix play-  
list. To restart, turn this function on.  
The MyMix function is on as the default set-  
ting.  
1
Switch to memo edit mode.  
The MyMix playlist is displayed.  
%
Turn the MyMix function on or off.  
2
Delete the song title.  
Deleting the song title.  
Setting up a song alert  
You can set up an alert (on or off) for each  
song in the MyMix playlist. First, display the  
Deleting all the songs in the MyMix  
playlist.  
39  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
That song will be deleted from the MyMix play-  
list.  
A message to confirm deletion will appear.  
Selecting teams for Game Alert  
1
Start Game Alert setup.  
3
Touch Yes.  
#
To cancel deletion, touch No.  
2
3
4
Select a desired league in League.  
Deleting a song from the  
MyMix playlist for SIRIUS tuner  
You can delete each song in the MyMix play-  
list.  
Switching the league name.  
1
Switch to memo edit mode.  
Select a desired team in Team.  
2
Select the song title that you want to  
Switching the team name.  
delete.  
Selecting the song title that you  
want to delete.  
Turn the alert on or off.  
Turning the alert on or off.  
3
Delete the song title.  
The game alert function is activated for that  
team.  
Deleting the song title.  
#
When you have already selected 12 teams,  
FULL is displayed and additional teams cannot  
be selected. In this case, first delete a selected  
team and then try again.  
A message to confirm deletion will appear.  
Touch Yes.  
That song will be deleted from the MyMix play-  
list.  
4
5
Repeat these steps to select other  
teams.  
Up to 12 teams can be selected.  
#
To cancel deletion, touch No.  
Switching the Game Alert on or off  
Once you select the teams, you need to turn  
the Game Alert function on.  
The Game Alert function is on at the default  
setting.  
Using the Game Alert function  
This system can alert you when games invol-  
ving your favorite teams are about to start. To  
use this function you need to set up a game  
alert for the teams in advance.  
!
This function is available for SIR-PNR2/SIR-  
PNR2C.  
40  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
%
Select CH000.  
When a game of a selected  
team starts  
When a game of the selected team is about to  
start (or is currently playing) on a different sta-  
tion, a game alert is displayed.  
Switching the SIRIUS display  
Switching to the other station to lis-  
ten to the game.  
!
Actions will differ depending on the con-  
nected SIRIUS tuner.  
%
Touch SIRIUS information to switch the  
Not tuning in to the other station.  
SIRIUS display.  
Channel numberChannel nameCategory  
nameArtist nameSong title/Title name—  
Composer namePlay time  
Displaying game information  
If any games of the selected teams are cur-  
rently playing, you can display information on  
the games and tune in to the broadcast chan-  
nel.  
Note  
Play time is displayed during the Instant Replay  
mode.  
1
Display the game information for the  
selected team.  
Using the Instant Replay  
function  
The following functions can be operated in In-  
stant Replay mode.  
2
Touch c or d to select a game.  
The game is displayed, followed by more de-  
tailed game information.  
!
!
To use this function, a Pioneer SIRIUS bus  
interface (e.g. CD-SB10) is required.  
To use this function, a SIRIUS plug-and-  
play unit with an Instant Replay Function is  
required.  
!
The game score will be updated automati-  
cally.  
3
Switch to the other station to listen to  
the game.  
!
For details, refer to the SIRIUS plug-and-  
play units manuals.  
Switching to the other station to lis-  
ten to the game.  
%
To exit from Instant Replay mode, se-  
lect another source or touch the following  
#
If you have not selected any teams, NOT SET  
icon.  
is displayed.  
#
When games involving your favorite teams are  
not currently playing, NO GAME is displayed.  
Exiting from Instant Replay mode.  
%
Select a track  
Displaying the Radio ID  
Channel number selection setting  
Press c or d (TRACK/SEEK).  
%
Fast forward or reverse  
If you select CH000, the ID code is displayed.  
Press and hold c or d (TRACK/SEEK).  
41  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
%
Pause and play  
Using the missed, received  
and dialed call lists on the  
optional Bluetooth adapter  
Playing and pausing.  
The 3 most recent calls dialed, received, and  
missed are stored in the memory. You can  
browse them and call numbers from these  
lists.  
Switching the seek mode  
There are two seek tuning settings, one is  
Seek HD (Digital broadcasting stations seek)  
and the other is Seek All (normal seek).  
1
Switch to the call history list.  
2
Touch a phone number or name (if en-  
Seek AllSeek HD  
tered) you want to call.  
3
Make the call.  
Switching the reception mode  
If the reception for a digital broadcast be-  
comes poor, this unit automatically switches  
to the analog broadcast of the same fre-  
quency. If this function is set to D/A Auto, the  
tuner switches between digital broadcast and  
analog broadcast automatically. If this func-  
tion is set to Analog, the tuner will only re-  
ceive analog broadcasts.  
4
End the call.  
Setting automatic answering  
If this function is on, this unit automatically  
answers all incoming calls.  
D/A AutoAnalog  
Note  
%
Turn automatic answering on or off.  
If SEEK MODE is set to Seek HD and BLENDING  
is set to Analog, the tuner cannot receive broad-  
casts. In this case, the seek mode or reception  
mode is changed automatically as follows:  
!
When SEEK MODE is set to Seek HD, if you  
switch BLENDING from D/A Auto to Analog,  
SEEK MODE is changed to Seek All.  
When BLENDING is set to Analog, if you  
switch SEEK MODE from Seek All to  
Seek HD, BLENDING is changed to  
D/A Auto.  
Switching the ring tone  
You can select whether or not to use this  
units ring tone. If this function is set to on,  
the ring tone for this unit will sound.  
!
1
Connect your cellular phone to this  
unit.  
2
Turn ring tone on or off.  
42  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Detailed instructions  
12  
Using a cellular phone to  
initiate a connection  
A Bluetooth wireless connection can be estab-  
lished from your phone by putting the unit into  
initiating a connection mode.  
You may need to refer to the operation manual  
that came with your phone if you are unsure  
how to initiate a connection from your phone.  
Voice recognition  
If your cellular phone features voice recogni-  
tion technology, you can make a call by voice  
commands.  
!
Operation varies depending on the type of  
cellular phone. Refer to the instruction  
manual that came with your cellular phone  
for detailed instructions.  
1
Start voice recognition.  
1
Put the unit in initiating a connection  
mode.  
2
Say the name of your contact aloud.  
2
Use a cellular phone to connect to this  
unit.  
Connecting a Bluetooth  
audio player  
A Bluetooth wireless connection can be estab-  
lished by putting the unit into initiating a con-  
nection mode.  
#
Operation varies depending on the type of cel-  
lular phone.  
#
cellular phone to complete the connection.  
You may need to enter the link code on your  
Registering a connected  
cellular phone  
You can register a phone that is temporarily  
connected to this unit in order to take full ad-  
vantage of the features available with Blue-  
tooth wireless technology. Only one cellular  
phone can be registered.  
%
mode.  
Put the unit in initiating a connection  
This unit is now on standby for connection  
from Bluetooth audio player.  
If your Bluetooth audio player is set ready for  
Bluetooth wireless connection, connection to  
this unit is automatically established.  
1
Start registering a connected cellular  
phone.  
Connecting to a Bluetooth  
device automatically  
2
Use cellular phone to register to this  
If this function is set to on, a connection be-  
tween your Bluetooth device and this unit will  
take place automatically as soon as the two  
devices are less than a few meters apart.  
Initially, this function is set to on.  
unit.  
If registration is successful, you can browse  
the dialed, received, and missed call lists.  
#
To replace an assignment with a new phone,  
first delete the current assignment.  
If registration failed, return to step 1 and try  
again.  
#
1
Touch Auto Connect to turn automatic  
connection on.  
43  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
12  
Detailed instructions  
If your Bluetooth device is ready for a Blue-  
tooth wireless connection, a connection to  
this unit will automatically be established.  
#
To turn automatic connection off, touch  
Auto Connect again.  
2
Turn your vehicles ACC switch off and  
on.  
Displaying Bluetooth  
Device address  
This unit displays its Bluetooth Device ad-  
dress.  
%
Touch Bluetooth Version to display de-  
vice information.  
The Bluetooth Device address is displayed.  
44  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Menu operations  
13  
!
You cannot display the Audio function menu  
when the mute function/attenuation is on or a  
JPEG file is playing.  
Introduction of menu  
operations  
21  
Audio  
Fader/Balance  
Graphic EQ  
Loudness  
F/R 0 L/R  
0
Super Bass  
High  
Off  
0
Subwoofer  
Bass Booster  
High Pass Filter  
Off  
345  
1
Display menus.  
2
Touch any of the following touch panel  
keys to select the menu to be adjusted.  
Touch panel keys  
!
Video Setup menu  
1
Audio function menu  
2
3
4
System menu  
Entertainment menu  
Custom menu  
You can choose menus within  
each menu (Audio function  
menu, etc.) and register them  
to this custom menu.  
5
Notes  
!
You can display the Video Setup menu when  
a Disc or USB source is selected.  
If you start the Video Setup menu, playback  
is stopped.  
!
45  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
13  
Menu operations  
Audio Adjustments  
Note  
Display  
Vocal  
Equalizer curve  
Vocal  
When selecting FM as the source, you cannot  
switch to Source Level Adjuster.  
Custom1  
Custom2  
Flat  
Custom 1  
Custom 2  
Flat  
Using fader/balance adjustment  
You can change the fader/balance setting to  
provide an ideal listening environment for all  
of the occupied seats.  
Super Bass  
Super bass  
!
!
The equalizer curves for Custom1 and  
Custom2 can be adjusted.  
When Flat, no changes are made to the  
sound. You can check the effects of the  
equalizer curves by switching alternatively  
between Flat and another equalizer curve.  
1
Display the audio function menu.  
2
Touch Fader/Balance on the audio func-  
1
Display the audio function menu.  
tion menu.  
3
Touch a or b to adjust the front/rear  
speaker balance.  
Range: Front:15 to Rear:15  
2
Touch Graphic EQ on the audio function  
menu.  
#
Select F/R: 0 L/R: 0 when only using two  
speakers.  
3
Touch c or d to select the desired item.  
#
The front/rear speaker balance cannot be ad-  
PowerfulNaturalVocalCustom1—  
Custom2FlatSuper Bass  
justed when the rear output setting is  
Subwoofer. Refer to Setting the rear output and  
Adjusting the 5-band graphic equalizer  
You can adjust the level of each band for the  
equalizer curves.  
4
Touch c or d to adjust the left/right  
speaker balance.  
Range: Left:15 to Right:15  
!
A separate Custom1 curve can be created  
for each source. If you make adjustments  
when a curve other than Custom2 is se-  
lected, the equalizer curve settings will be  
stored in Custom1.  
A Custom2 curve that is common for all  
sources can be created. If you make adjust-  
ments when the Custom2 curve is se-  
lected, the Custom2 curve will be updated.  
Using the equalizer  
You can adjust the equalization to match the  
cars interior acoustic characteristics as de-  
sired.  
!
Recalling equalizer curves  
There are seven stored equalizer curves which  
you can easily recall at any time. Here is a list  
of the equalizer curves.  
1
Display the audio function menu.  
Display  
Powerful  
Natural  
Equalizer curve  
Powerful  
2
Touch Graphic EQ on the audio function  
menu.  
Natural  
46  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Menu operations  
13  
3
Touch c or d to select the desired item.  
5
Touch c or d next to Level to adjust  
PowerfulNaturalVocalCustom1—  
the output level of the subwoofer.  
Custom2FlatSuper Bass  
Range: +6 to -24  
4
5
Touch the Equalizer band to adjust.  
6
Touch c or d next to Frequency to se-  
lect the cut-off frequency.  
Touch a or b to adjust the level of the  
50Hz63Hz80Hz100Hz125Hz  
Only frequencies lower than those in the se-  
lected range are outputted from the subwoo-  
fer.  
equalizer band.  
Range: +12dB to -12dB  
#
You can then select another band and adjust  
the level.  
Boosting the bass  
You can boost the bass level.  
Adjusting loudness  
Loudness compensates for deficiencies in the  
low- and high-frequency ranges at low volume.  
1
Display the audio function menu.  
1
Display the audio function menu.  
2
Touch c or d to select a desired level.  
Range: 0 to +6  
2
Touch Loudness on the audio function  
menu.  
Using the high pass filter  
3
Touch c or d to select a desired level.  
When you do not want low sounds from the  
subwoofer output frequency range to play  
from the front or rear speakers, turn on the  
HPF (high pass filter). Only frequencies higher  
than those in the selected range are output  
from the front or rear speakers.  
Off (off)Low (low)Mid (mid)High  
(high)  
Using subwoofer output  
This unit is equipped with a subwoofer output  
which can be turned on or off.  
1
Display the audio function menu.  
!
The cut-off frequency and output level can  
be adjusted when the subwoofer output is  
on.  
2
Touch c or d next to Frequency to se-  
1
Display the audio function menu.  
lect cut-off frequency.  
Off (off)50Hz63Hz80Hz100Hz—  
125Hz  
Only frequencies higher than those in the se-  
lected range are output from the front or rear  
speakers.  
2
Touch Subwoofer on the audio function  
menu.  
3
Touch On or Off next to Subwoofer to  
turn the subwoofer output on or off.  
4
Touch Normal or Reverse next to Phase  
to select the phase of subwoofer output.  
47  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
13  
Menu operations  
Adjusting source levels  
Setting up the DVD player  
Setting the subtitle language  
You can set a desired subtitle language. When  
available, the subtitles will be displayed in the  
selected language.  
With SLA (source level adjustment), the vo-  
lume levels of each source can be adjusted to  
prevent significant differences between  
sources.  
!
Settings are based on the FM volume level,  
which remains unchanged.  
1
Display the Video Setup menu.  
1
Display the audio function menu.  
2
Touch Subtitle Language on the  
Video Setup menu.  
A subtitle language menu is displayed.  
2
Compare the FM volume level with the  
level of the source you wish to adjust.  
3
Touch the desired language.  
The subtitle language is set.  
If you have selected Others, refer to When you  
3
Touch Source Level Adjuster on the  
audio function menu.  
#
4
Touch a or b to adjust the source vo-  
lume.  
Range: +4 to 4  
Notes  
!
If the selected language is not available, the  
language specified on the disc is displayed.  
You can also switch the subtitle language by  
touching the icon during playback. (Refer to  
Playing moving images on page 16.)  
The setting made here will not be affected  
even if the subtitle language is switched dur-  
ing playback using Subtitle.  
Notes  
!
The AM volume level can also be adjusted  
with this function.  
Video CD, CD, compressed audio and DivX  
are automatically set to the same source level  
adjustment volume.  
iPod and USB storage device are automati-  
cally set to the same source level adjustment  
volume.  
External unit 1 and external unit 2 are automa-  
tically set to the same source level adjustment  
volume.  
!
!
!
!
!
When you select Others  
A language code input display is shown when  
Others is selected. Refer to Language code  
1
Touch 0 to 9 to input the language  
code.  
#
To cancel the entered numbers, touch C.  
Registering the code.  
2
Registering the code.  
Setting the audio language  
You can set the preferred audio language.  
48  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Menu operations  
13  
1
Display the Video Setup menu.  
1
Display the Video Setup menu.  
2
Touch Audio Language on the Video  
2
Touch Multi Angle on the Video Setup  
Setup menu.  
menu to turn angle icon display on or off.  
An audio language menu is displayed.  
3
Touch the desired language.  
The audio language is set.  
If you have selected Others, refer to When you  
Setting the aspect ratio  
There are two kinds of display: a wide screen  
display that has a width-to-height ratio (TV as-  
pect ratio) of 16:9, and regular display that has  
a TV aspect of 4:3. Be sure to select the correct  
TV aspect for the display connected to V OUT.  
#
Notes  
!
If the selected language is not available, the  
language specified on the disc is used.  
You can also switch the audio language by  
touching Audio during playback. (Refer to  
Playing moving images on page 16.)  
The setting made here will not be affected  
even if the audio language is switched during  
playback using Audio.  
!
When using regular display, select either  
Letter Box or Pan Scan. Selecting 16 : 9  
may result in an unnatural picture.  
!
!
If you select the TV aspect ratio, the units  
display will change to the same setting.  
!
1
Display the Video Setup menu.  
Setting the menu language  
You can set the preferred language in which  
the menus recorded on a disc are displayed.  
2
Touch TV Aspect on the Video Setup  
menu to select the TV aspect ratio.  
Touch TV Aspect repeatedly until the desired  
aspect ratio appears.  
1
Display the Video Setup menu.  
!
16 : 9 Wide screen picture (16:9) is dis-  
played as is (initial setting)  
!
Letter Box The picture is the shape of a  
letterbox with black bands on the top and  
bottom of the screen  
Pan Scan The picture is cut short on the  
right and left sides of the screen  
2
Touch Menu Language on the  
Video Setup menu.  
A menu language menu is displayed.  
!
3
Touch the desired language.  
The menu language is set.  
If you have selected Others, refer to When you  
Notes  
!
When playing discs that do not specify  
#
Pan Scan, the disc is played back in  
Letter Box display even if you select the  
Pan Scan setting. Confirm whether the disc  
16 : 9 LB  
Note  
package bears the  
mark.  
If the selected language is not available, the lan-  
guage specified on the disc is displayed.  
!
The TV aspect ratio cannot be changed for  
some discs. For details, refer to the discs in-  
structions.  
Setting the multi-angle DVD  
display  
The angle icon can be set so it appears on  
scenes where the angle can be switched.  
49  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
13  
Menu operations  
4
Registering the code.  
Setting the slide show interval  
JPEG files can be viewed as a slide show on  
this unit. In this setting, the interval between  
each image can be set.  
Registering the code.  
1
Display the Video Setup menu.  
The code number is set, and the level can now  
be set.  
5
Touch 1 to 8 to select the desired level.  
2
Touch Time Per Photo Slide on the  
6
Touch Enter.  
Video Setup menu to select the slide show  
interval.  
Touch Time Per Photo Slide repeatedly until  
the desired setting appears.  
The parental lock level is set.  
!
!
!
8 Playback of the entire disc is possible  
(initial setting)  
7 to 2 Playback of discs for children and  
non-adult-oriented discs is possible  
1 Playback of discs for children only is  
possible  
!
!
!
!
5sec JPEG images switch at intervals of 5  
seconds  
10sec JPEG images switch at intervals of  
10 seconds  
15sec JPEG images switch at intervals of  
15 seconds  
Notes  
!
We recommend to keep a record of your code  
Manual JPEG images can be switched  
manually  
number in case you forget it.  
!
The parental lock level is stored on the disc.  
Look for the level indication written on the  
disc package, included literature or on the  
disc itself. Parental lock of this unit is not pos-  
sible if a parental lock level is not stored on  
the disc.  
Setting parental lock  
Some DVD video discs let you use parental  
lock to restrict children from viewing violent  
and adult-oriented scenes. You can set paren-  
tal lock to the desired level.  
!
With some discs, the parental lock may be ac-  
tive only for certain levels of scenes. The play-  
back of those scenes will be skipped. For  
details, refer to the instruction manual that  
came with the disc.  
!
When you have a parental lock level set  
and play a disc featuring parental lock,  
code number input indications may be dis-  
played. In such cases, playback will begin  
when the correct code number is entered.  
Changing the level  
You can change the set parental lock level.  
Setting the code number and level  
A code number must be registered in order to  
play back discs with parental lock.  
1
Display the Video Setup menu.  
1
Display the Video Setup menu.  
2
Touch Parental on the Video Setup  
menu.  
2
Touch Parental on the Video Setup  
3
Touch 0 to 9 to input the registered  
menu.  
code number.  
3
Touch 0 to 9 to input a four digit code  
number.  
#
To cancel the entered numbers, touch C.  
50  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Menu operations  
13  
â
4
Registering the code.  
Displaying the DivX VOD  
registration code  
Registering the code.  
In order to play DivX VOD (video on demand)  
contents on this unit, the unit must first be re-  
gistered with a DivX VOD contents provider.  
For registration, generate a DivX VOD registra-  
tion code and submit it to your provider.  
This sets the code number, and the level can  
now be changed.  
If you enter an incorrect code number, the  
icon is displayed. Touch C and enter the correct  
#
!
Keep a record of the code as you will need  
it when you register your unit to the DivX  
VOD provider.  
code number.  
#
If you forget your code number, refer to If you  
1
Display the Video Setup menu.  
5
6
Touch 1 to 8 to select the desired level.  
Touch Enter.  
2
Touch DivX VOD on the Video Setup  
The new parental lock level is set.  
menu.  
Registration Code and Deregistration Code  
appear.  
If you forget your code number  
Press RESET.  
3
Touch Registration Code.  
Your registration code is displayed.  
Setting the DivX subtitle file  
You can select whether or not to display DivX  
external subtitles.  
Displaying the deregistration code  
If your device is already activated, deregister it  
by entering the deregistration code.  
!
The DivX subtitles will be displayed even  
when Custom is selected if no DivX exter-  
nal subtitle files exist.  
1
Display the Video Setup menu.  
1
Display the Video Setup menu.  
2
Touch DivX VOD on the Video Setup  
menu.  
2
Touch DivX Subtitle on the Video Setup  
3
Touch Deregistration Code.  
menu to select the desired subtitle setting.  
#
To cancel deregistration, touch Cancel.  
!
!
Original Display the DivX subtitles  
Custom Display the DivX external subti-  
tles  
4
Touch OK.  
The deregistration is complete.  
Notes  
!
Up to 42 characters can be displayed on one  
Automatic playback of DVDs  
line. If more than 42 characters are set, the  
line breaks and the characters are displayed  
on the next line.  
Up to 126 characters can be displayed on one  
screen. If more than 126 characters are set,  
the excess characters will not be displayed.  
When a DVD disc with a DVD menu is in-  
serted, this unit will cancel the menu automa-  
tically and start playback from the first chapter  
of the first title.  
!
!
Some DVDs may not operate properly. If  
this function is not fully operated, turn this  
function off and start playback.  
51  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
13  
Menu operations  
1
Display the Video Setup menu.  
System settings  
Switching the auxiliary setting  
Activate this setting when using an auxiliary  
device connected to this unit.  
2
Touch DVD Auto Play to turn automatic  
playback on.  
To turn automatic playback off, touch  
#
1
Display the system menu.  
DVD Auto Play again.  
2
Touch AUX Input on the system menu  
to turn AUX Input on or off.  
Setting AV input  
Activate this setting when using an external  
video component connected to this unit.  
1
Display the system menu.  
2
Touch AV Input on the system menu to  
turn AV Input on or off.  
Setting the rear output and  
subwoofer controller  
This unit's rear speaker leads can be con-  
nected with full-range speaker (Full) or sub-  
woofer (Subwoofer). If you switch the rear  
speaker setting to Subwoofer, you can con-  
nect the lead directly to a subwoofer without  
using an auxiliary amp.  
!
When no subwoofer is connected to the  
rear output, select Full (full-range speaker).  
If the rear speaker leads are connected  
with a subwoofer, select Subwoofer (sub-  
woofer).  
!
This unit's rear output (RCA rear output) can  
be used for subwoofer (Subwoofer) or rear  
(Rear Speaker) connection.  
!
When no subwoofer is connected to the  
rear output, select Rear Speaker (Rear).  
When a subwoofer is connected to the rear  
output, select Subwoofer (subwoofer).  
!
1
Turn the unit off.  
52  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Menu operations  
13  
!
!
When ATT is displayed, the sound is attenu-  
ated and no other audio adjustments can be  
made.  
Operation returns to normal when the phone  
connection is ended.  
2
Display the system menu.  
3
Touch Rear Speaker on the system  
menu.  
4
Touch Rear Speaker to switch the sub-  
Selecting the menu language  
The menu language can be selected from four  
languages.  
woofer output or full-range speaker.  
5
Touch Preout to switch the subwoofer  
or rear output.  
If text information such as the title name, artist  
name or a comment is embedded in a Eur-  
opean language, they can also be displayed  
on this unit.  
Notes  
!
!
Even if you change this setting, there will be  
no output unless you turn the subwoofer out-  
If you change this setting, subwoofer output  
in the audio menu will return to the factory  
settings.  
!
The language can be changed for the fol-  
lowing:  
System menu  
Video Setup  
On-screen display  
Multi language setting for DivX  
Language for cautions  
Some operations on this unit are prohib-  
ited from use while driving or require  
careful attention when operated. In  
such cases, a caution will appear on the  
display. You can change the language  
for caution messages with this setting.  
If the embedded language and the selected  
language setting are not the same, text in-  
formation may not display properly.  
Some characters may not be displayed  
properly.  
Switching sound muting/  
attenuation  
Sound from this system is automatically  
muted or attenuated when a signal from  
equipment with a mute function is received.  
!
Sound from this system returns to normal  
when the muting or attenuation is can-  
celed.  
!
!
!
1
Display the system menu.  
To complete this operation, switch the igni-  
tion key off and on after you set this set-  
ting.  
2
Touch Mute/ATT until the desired set-  
ting appears.  
Touch Mute/ATT until the desired setting ap-  
pears in the display.  
1
Display the system menu.  
!
!
Mute Muting  
ATT-20dB Attenuation (ATT-20dB has a  
stronger effect than ATT-10dB)  
ATT-10dB Attenuation  
Off Turns the sound muting/attenuation  
off  
2
Touch System Language on the system  
menu to select the desired language.  
!
!
3
Touch the desired language.  
English (English)Français (French)—  
Español (Spanish)Português (Portuguese)  
Notes  
When Mute is displayed, the sound is turned  
off and no audio adjustments can be made.  
!
53  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
13  
Menu operations  
Setting the rear view camera  
(back up camera)  
Setting the video signal  
When you connect this unit to an AV equip-  
ment to this unit, select the suitable video sig-  
nal setting.  
CAUTION  
Pioneer recommends the use of a camera  
which outputs mirror-reversed images.  
Otherwise, the screen image will appear re-  
versed.  
!
As this function is initially set to Auto, the  
unit will automatically adjust the video sig-  
nal setting.  
However, the screen may turn black or  
images may not be displayed properly  
when Auto has been selected and the re-  
ception is weak. Normally, select the appro-  
priate video signal.  
This unit features a function that automatically  
switches to the rear view camera video (R.C  
IN) when a rear view camera is installed on  
your car and the gear shift is moved to the RE-  
VERSE (R) position. (For more details, con-  
sult your dealer.)  
1
Display the system menu.  
!
After you set up the rear view camera set-  
ting, move the gear shift to REVERSE (R)  
and confirm that the rear view camera  
video is shown on the display.  
2
Touch Video Signal Setting on the func-  
tion menu.  
!
!
!
Change this setting if the display switches  
to the rear view camera video by error while  
you are driving forward.  
To stop watching the rear view camera  
video and return to the source display,  
press and hold MUTE.  
Touch the RearView source icon to display  
the rear view camera image while driving.  
Touch the source icon again to turn the  
rear view camera off. For details, refer to Se-  
Video Signal Setting items are displayed.  
!
!
!
AV Adjusts the AV video signal  
AUX Adjusts the AUX video signal  
Camera Adjusts the rear view camera  
video signal  
3
Touch c or d to select the desired  
video signal appears.  
AutoPALNTSCPAL-MPAL-N—  
SECAM  
1
Display the system menu.  
2
Touch Camera Polarity on the system  
menu to select the appropriate setting.  
!
!
!
Battery When the polarity of the con-  
nected lead is positive while the gear shift  
is in REVERSE (R) position  
Ground When the polarity of the con-  
nected lead is negative while the gear shift  
is in REVERSE (R) position  
Off When a rear view camera is not con-  
nected to this unit  
54  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Menu operations  
13  
Selecting the OSD color  
The OSD color can be changed.  
Entertainment settings  
Selecting the illumination color  
This unit is equipped with multiple-color illu-  
mination.  
1
Display the entertainment menu.  
Direct selection from preset  
illumination colors  
You can select an illumination color from the  
color list.  
2
3
4
Touch Appearance.  
Touch Screen.  
Touch one of the colors on the list.  
1
Display the entertainment menu.  
Selecting the background display  
You can switch the background that is dis-  
played when listening to a source.  
2
Touch Appearance.  
1
Display the entertainment menu.  
3
Touch Illumination and then touch a  
color on the list.  
Customizing the illumination color  
2
Touch Background.  
1
Display the entertainment menu.  
3
#
Touch the desired setting.  
If no JPEG images are stored in this unit, you  
cannot select photo. To store a JPEG image to  
2
Touch Appearance.  
3
Touch Illumination and then touch  
Custom icon.  
Custom icon  
4
Touch the color bar to customize the  
color.  
5
6
Touch c or d to fine-tune the color.  
Touch the Memo icon and hold to store  
the customized color in the memory.  
Memo  
Memo icon  
The customized color has been stored in the  
memory.  
The set color will be recalled from the memory  
the next time you touch the same icon.  
55  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
13  
Menu operations  
Customizing menus  
1
Display menu columns to register.  
You can customize menus except  
Video Setup menu.  
2
Touch and hold the menu column to  
register it.  
#
To cancel registration, touch and hold the  
menu column again.  
3
Display the custom menu and choose a  
registered menu.  
Note  
You can register up to 12 columns.  
56  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Other Functions  
14  
#
You cannot adjust the picture adjustment for  
Changing the picture  
adjustment  
You can adjust the Brightness (brightness),  
Contrast (contrast), Color (color) , Hue (hue),  
Dimmer (dimmer), Temperature (tempera-  
ture), Black Level (black level) and  
the rear view camera when Camera Polarity is  
set to Off. (Refer to Setting the rear view camera  
#
If the color system is set to PAL/PAL-N/PAL-M/  
SECAM, you cannot adjust Hue.  
With some rear view cameras, picture adjust-  
ment may not be possible.  
#
RGB Dot ADJ (RGB dot clock adjustment) for  
each source and rear view camera.  
4
Touch c or d to adjust the selected  
!
You cannot adjust Color, Hue, Contrast  
and Black Level for the audio source.  
item.  
Each time you touch c or d, the level of the  
selected item increases or decreases.  
1
Press and hold MENU to display  
Picture Adjustment.  
The adjustment function names are displayed.  
#
#
Dimmer can be adjusted from +1 to +48.  
Temperature can be adjusted from +3 to 3.  
2
If you are adjusting the  
5
Touch Black Level and RGB Dot ADJ to  
Picture Adjustment, select the unit.  
adjust.  
#
#
Black Level can be set on or off.  
RGB Dot ADJ can be set to 1 or 2.  
Adjusting the Picture Adjustment  
for the Navigation system.  
NAVI  
Notes  
!
!
You cannot operate this function while driving.  
Different Brightness/Contrast/Dimmer set-  
tings can be set for when the illumination  
switch is on and when it is off.  
Rear  
View  
Adjusting the Picture Adjustment  
for the rear view camera.  
Adjusting the Picture Adjustment  
for the source.  
Source  
Adjusting the response  
positions of the touch panels  
(Touch Panel Calibration)  
3
Touch any of the following touch panel  
keys to select the function to be adjusted.  
Picture Adjustment items are displayed.  
If you feel that the touch panel keys on the  
screen deviate from the actual positions that  
respond to your touch, adjust the response po-  
sitions of the touch panel. There are two ad-  
justment methods: 4-point adjustment, in  
which you touch four corners of the screen;  
and 16-point adjustment, in which you make  
fine-adjustments on the entire screen.  
!
!
!
!
Brightness Adjusts the black intensity  
Contrast Adjusts the contrast  
Color Adjusts the color saturation  
Hue Adjusts the tone of color (red or  
green is emphasized)  
!
!
!
Dimmer Adjusts the brightness of the dis-  
play  
Temperature Adjusts the color tempera-  
ture, resulting in a better white balance  
Black Level Emphasizes the dark portions  
of images making the difference between  
bright and dark more distinct  
RGB Dot ADJ Adjusts phase shifting by  
dot clock when a Navigation system is con-  
nected  
!
Touch the screen gently for adjustment.  
Forcefully pressing the touch panel may da-  
mage the touch panel. Do not use a sharp  
pointed tool such as a ballpoint pen or me-  
chanical pen. Doing so may damage the  
screen.  
!
57  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
14  
Other Functions  
!
If the touch panel cannot be adjusted prop-  
erly, consult your local Pioneer dealer.  
is automatically recognized as an AUX source  
and is assigned to AUX.  
1
Turn the unit off.  
About AUX connection methods  
You can connect auxiliary devices to this unit.  
2
Press and hold MENU to display  
Picture Adjustment.  
Mini pin plug cable (AUX)  
When connecting an auxiliary device using a  
mini plug cable  
iPods and portable audio/video players can be  
connected to this unit via mini plug cable.  
3
Press and hold MENU to start Touch  
Panel Calibration.  
The 4-point touch panel adjustment screen ap-  
pears.  
!
If an iPod with video capabilities is con-  
nected to this unit via 3.5 mm plug (4 pole)  
cable (such as the CD-V150M), you can  
enjoy the video contents of the connected  
iPod.  
A portable audio/video player can be con-  
nected by using a 3.5 mm plug (4 pole) with  
an RCA cable (sold separately). However,  
depending on the cable, a reverse connec-  
tion between the red (right side audio)  
cable and yellow (video) cable may be re-  
quired in order for the sound and video  
image to be reproduced correctly.  
4
Touch each of the arrows on the four  
corners of the screen.  
To cancel the adjustment, press and hold  
MENU.  
#
5
Press MENU to complete 4-point adjust-  
!
ment.  
Data for the adjusted position is saved.  
#
being saved.  
Do not turn off the engine while the data is  
6
Press MENU to proceed to 16-point ad-  
justment.  
The 16-point touch panel adjustment screen  
appears.  
#
%
Insert the stereo mini plug into the  
To cancel the adjustment, press and hold  
AUX input jack on this unit.  
Refer to Whats what on page 10.  
MENU.  
7
Gently touch the center of the + mark  
displayed on the screen.  
After you touch all the marks, the data for the  
adjusted position is saved.  
Using an external unit  
An external unit refers to a Pioneer product,  
such as those which will be available in the fu-  
ture. Although incompatible as a source, the  
basic functions of up to two external units can  
be controlled with this unit. When two external  
units are connected, the external units are  
automatically allocated to external unit 1 or ex-  
ternal unit 2.  
#
Do not turn off the engine while the data is  
being saved.  
8
Press and hold MENU to complete the  
adjustment.  
Using an AUX source  
A separately sold auxiliary device such as a  
VCR or portable device can be connected to  
this unit. When connected, the auxiliary device  
58  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Other Functions  
14  
The basic operations of the external unit are  
explained below. The allocated functions will  
differ depending on the connected external  
unit. For details concerning these functions,  
refer to the owners manual for the external  
unit.  
F1  
F2  
F3  
F4  
Function 1 to 4  
Actions will differ depending on  
the connected external unit.  
Basic operations  
The functions allocated to the following opera-  
tions will differ depending on the connected  
external unit. For details concerning these  
functions, refer to the owners manual for the  
connected external unit.  
Using the functions allocated to 1  
to 6 keys.  
Actions will differ depending on  
the connected external unit.  
Auto  
Switching to auto or manual.  
Audio  
Switching to video and audio.  
Video  
Changing the screen mode.  
Switching the equalizer curves.  
Actions will differ depending on  
the connected external unit.  
59  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
15  
Installation  
Connecting the units  
WARNING  
!
LIGHT GREEN LEAD AT POWER CON-  
NECTOR IS DESIGNED TO DETECT  
PARKED STATUS AND MUST BE CON-  
NECTED TO THE POWER SUPPLY SIDE  
OF THE PARKING BRAKE SWITCH. IM-  
PROPER CONNECTION OR USE OF  
THIS LEAD MAY VIOLATE APPLICABLE  
LAW AND MAY RESULT IN SERIOUS IN-  
JURY OR DAMAGE.  
WARNING  
!
To avoid the risk of accident and the potential  
violation of applicable laws, no viewing of  
front seat video should ever occur while the  
vehicle is being driven. Also, rear displays  
should not be in a location where they are visi-  
bly distracting to the driver.  
!
In some countries or states the viewing of  
images on a display inside a vehicle even by  
persons other than the driver may be illegal.  
Where such regulations apply, they must be  
obeyed and this units DVD features should  
not be used.  
WARNING  
!
!
Use speakers over 50 W (output value) and be-  
tween 4 W to 8 W (impedance value). Do not  
use 1 W to 3 W speakers for this unit.  
The black cable is ground. When installing  
this unit or power amp (sold separately), make  
sure to connect the ground wire first. Ensure  
that the ground wire is properly connected to  
metal parts of the cars body. The ground wire  
of the power amp and the one of this unit or  
any other device must be connected to the car  
separately with different screws. If the screw  
for the ground wire loosens or falls out, it  
could result in fire, generation of smoke or  
malfunction.  
CAUTION  
!
PIONEER does not recommend that you in-  
stall or service your display unit yourself. In-  
stalling or servicing the product may expose  
you to risk of electric shock or other hazards.  
Refer all installation and servicing of your dis-  
play unit to authorized Pioneer service person-  
nel.  
!
!
Secure all wiring with cable clamps or electri-  
cal tape. Do not allow any bare wiring to re-  
main exposed.  
Do not drill a hole into the engine compart-  
ment to connect the yellow cable of the dis-  
play unit to the vehicle battery. Engine  
vibration may eventually cause the insulation  
to fail at the point where the wire passes from  
the passenger compartment into the engine  
compartment. Take extra care in securing the  
wire at this point.  
POWER AMP  
Ground wire  
Other devices  
(Another electronic  
device in the car)  
Metal parts of cars body  
!
It is extremely dangerous to allow the micro-  
phone lead to become wound around the  
steering column or gearstick. Be sure to in-  
stall the unit in such a way that it will not ob-  
struct driving.  
!
!
Make sure that cables will not interfere with  
moving parts of the vehicle, such as the gear-  
shift, parking brake or seat sliding mechan-  
ism.  
Do not shorten any cables. If you do, the pro-  
tection circuit may fail to work properly.  
60  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Section  
Installation  
15  
na, connect it to the antenna booster power  
supply terminal.  
Important  
!
This unit cannot be installed in a vehicle with-  
out ACC (accessory) position on the ignition  
switch.  
!
!
Never connect the blue/white cable to the  
power terminal of an external power amp.  
Also, never connect it to the power terminal of  
the auto antenna. Doing so may result in bat-  
tery drain or a malfunction.  
IP-BUS connectors are color-coded. Be sure  
to connect connectors of the same color.  
ACC position  
No ACC position  
!
!
Use this unit with a 12-volt battery and nega-  
tive grounding only. Failure to do so may result  
in a fire or malfunction.  
To prevent a short-circuit, overheating or mal-  
function, be sure to follow the directions  
below.  
Disconnect the negative terminal of the  
battery before installation.  
Secure the wiring with cable clamps or ad-  
hesive tape. Wrap adhesive tape around  
wiring that comes into contact with metal  
parts to protect the wiring.  
Place all cables away from moving parts,  
such as the gear shift and seat rails.  
Place all cables away from hot places,  
such as near the heater outlet.  
Do not connect the yellow cable to the bat-  
tery by passing it through the hole to the  
engine compartment.  
Cover any disconnected cable connectors  
with insulating tape.  
Do not shorten any cables.  
Never cut the insulation of the power cable  
of this unit in order to share the power  
with other devices. The current capacity of  
the cable is limited.  
Use a fuse of the rating prescribed.  
Never wire the negative speaker cable di-  
rectly to ground.  
Never band together negative cables of  
multiple speakers.  
!
When this unit is on, control signals are sent  
through the blue/white cable. Connect this  
cable to the system remote control of an exter-  
nal power amp or the vehicles auto-antenna  
relay control terminal (max. 300 mA 12 V DC).  
If the vehicle is equipped with a glass anten-  
61  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
15  
Installation  
When connecting to separately sold power amp  
Rear output or  
subwoofer output  
Power amp  
(sold separately)  
To rear output or  
subwoofer output  
Power amp  
(sold separately)  
To front output  
Front output  
This product  
Connect with RCA cables  
(sold separately)  
System remote control  
Blue/white  
Connect to system control terminal of the  
power amp or auto-antenna relay control  
terminal. (max. 300 mA 12 V DC).  
Left  
Right  
Front speaker  
Front speaker  
Rear speaker or  
Subwoofer  
Rear speaker or  
Subwoofer  
Perform these connections when  
using the optional amplifier.  
62  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
Installation  
15  
Connecting the system  
HD Radio tuner  
(sold separately)  
Microphone  
for hands-free phoning  
(supplied with Bluetooth adapter)  
Black  
IP-BUS cable  
(Supplied with HD Radio tuner)  
Bluetooth adapter  
(e.g. CD-BTB200)  
(sold separately)  
Blue  
Black  
IP-BUS input  
IP-BUS cable  
(Supplied with Bluetooth adapter)  
This product  
63  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
15  
Installation  
Connecting the power cord  
26 pin cable (Supplied with Navigation system)  
This product  
Insert the 26 pin cable in the direction  
indicated in the figure.  
Navigation system  
can be connected  
(AVIC-U220 (sold  
separately)).  
RGB input  
Antenna input  
Please contact your dealer to inquire  
about the connectable navigation system.  
Fuse (10 A)  
Yellow  
Connect to the constant 12 V supply terminal.  
Orange/white  
Connect to lighting switch terminal.  
Fuse resistor  
Fuse resistor  
Red  
Connect to terminal controlled by ignition switch (12 V DC).  
Black (chassis ground)  
Connect to a clean, paint-free metal location.  
White  
Gray  
Front speaker  
Front speaker  
White/black  
Green  
Gray/black  
Violet  
Left  
Right  
Rear speaker or  
Subwoofer (4 Ω)  
Rear speaker or  
Subwoofer (4 Ω)  
Green/black  
Violet/black  
When using a subwoofer of 70 W (2 Ω), be sure to connect with Violet and Violet/black leads of this  
unit. Do not connect anything to Green and Green/black leads.  
Green  
Violet  
Subwoofer (4 Ω)  
Not used.  
× 2  
Green/black  
Violet/black  
64  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
Installation  
15  
Wired remote input  
Hard-wired remote control adaptor can be connected  
(sold separately).  
Fuse resistor  
Violet/white  
Of the two lead wires connected to the back lamp, connect the one  
in which the voltage changes when the gear shift is in the  
REVERSE (R) position. This connection enables the unit to  
sense whether the car is moving forwards or backwards.  
Yellow/black  
If you use an equipment with Mute function, wire this lead  
to the Audio Mute lead on that equipment. If not, keep the  
Audio Mute lead free of any connections.  
Connection method  
1. Clamp the lead.  
2. Clamp firmly with  
needle-nosed pliers.  
Note:  
· The position of the parking brake switch depends on the vehicle model. For details,  
consult the vehicle Owner’s Manual or dealer.  
Light green  
Parking brake  
switch  
Used to detect the ON/OFF status of the parking  
brake. This lead must be connected to the power  
supply side of the parking brake switch.  
Power supply side  
Ground side  
Blue/white  
Connect to system control terminal of the power amp or  
auto-antenna relay control terminal (max. 300 mA 12 V DC).  
With a 2 speaker system, do not connect anything to the speaker  
leads that are not connected to speakers.  
Note:  
· Change the initial setting of this unit. The  
subwoofer output of this unit is  
monaural.  
65  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
15  
Installation  
When connecting the external video component and the display  
Display with RCA input jacks  
(sold separately)  
To video input  
Rear monitor output (V OUT)  
RCA cables  
(sold separately)  
Video input  
(V IN)  
To video output  
To audio outputs  
Audio inputs  
(L IN, R IN)  
This product  
External video component (sold  
separately)  
!
It is necessary to change AV Input in  
System Menu when connecting the exter-  
nal video component.  
When using a display connected to rear video output  
This products rear video output is for connec-  
tion of a display to enable passengers in the  
rear seats to watch the DVD, etc.  
WARNING  
Never install the display in a location where it  
is visible to the driver while driving.  
!
66  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
Installation  
15  
Rear view camera input (R.C IN)  
When connecting with a rear  
view camera  
When this product is used with a rear view  
camera, it is possible to automatically switch  
from the video to rear view image when the  
gear shift is moved to REVERSE (R).  
This product  
WARNING  
RCA cable  
(sold separately)  
USE INPUT ONLY FOR REVERSE OR MIR-  
ROR IMAGE REAR VIEW CAMERA. OTHER  
USE MAY RESULT IN INJURY OR DAMAGE.  
To video output  
Fuse resistor  
CAUTION  
!
!
The screen image may appear reversed.  
The rear view camera function is to be used  
as an aid to keep an eye on trailers, or while  
backing up. Do not use for entertainment pur-  
poses.  
Rear view camera  
(sold separately)  
Violet/white  
Of the two lead wires  
connected to the back lamp,  
connect the one in which the  
voltage changes when the  
gear shift is in the REVERSE  
(R) position. This connection  
enables the unit to  
!
Objects in the rear view may appear closer or  
more distant than they actually are.  
sense whether the car is  
moving forwards or  
backwards.  
CAUTION  
You must use a camera which outputs mirror  
reversed images.  
It is necessary to set Camera Polarity properly in  
System Menu when connecting the rear view  
camera.  
67  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Section  
15  
Installation  
and tighten the screws at 3 or 4 locations on  
each side.  
Installation  
Notes  
!
!
!
Check all connections and systems before  
final installation.  
Do not use unauthorized parts as this may  
cause malfunctions.  
Consult your dealer if installation requires dril-  
ling of holes or other modifications to the vehi-  
cle.  
!
!
Do not install this unit where:  
it may interfere with operation of the vehi-  
cle.  
it may cause injury to a passenger as a re-  
sult of a sudden stop.  
Do not install the display where it may (i) ob-  
struct the drivers vision, (ii) impair the perfor-  
mance of any of the vehicles operating  
systems or safety features, including air bags,  
hazard lamp buttons or (iii) impair the drivers  
ability to safely operate the vehicle.  
The semiconductor laser will be damaged if it  
overheats. Install this unit away from hot  
places such as near the heater outlet.  
Optimum performance is obtained when the  
unit is installed at an angle of less than 30°.  
1
2
!
!
3
4
5
1 If the pawl gets in the way, bend it down.  
2 Factory radio mounting bracket  
3 Use either truss (5 mm × 8 mm) or flush  
surface (5 mm × 9 mm) screws, depending  
on the bracket screw holes.  
4 Frame  
In some types of vehicles, discrepancy may  
occur between the unit and the dashboard.  
If this happens, use the supplied frame to  
fill the gap.  
!
To some types of vehicles, this unit cannot be  
properly installed. In such case, use the op-  
tional installation kit (ADT-VA133).  
5 Dashboard or console  
Installation using the screw  
holes on the side of the unit  
%
Fastening the unit to the factory radio-  
mounting bracket.  
Position the unit so that its screw holes are  
aligned with the screw holes of the bracket,  
68  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Troubleshooting  
Common  
Symptom  
Cause  
Action (Refer-  
ence page)  
There is no  
image dis-  
played.  
The parking  
brake cable is  
not connected.  
Connect the park-  
ing brake cable,  
and apply the park-  
ing brake.  
Symptom  
Cause  
Action (Refer-  
ence page)  
The power will Leads and con-  
Confirm once more  
not turn on.  
The unit will  
not operate.  
nectors are incor- that all connec-  
rectly connected. tions are correct.  
The parking  
brake is not ap-  
plied.  
Connect the park-  
ing brake cable,  
and apply the park-  
ing brake.  
The fuse is  
blown.  
Rectify the cause  
and then replace  
the fuse. Be sure to  
install a fuse with  
the same rating.  
The  
This operation is  
icon is The operation is  
displayed, and prohibited for the not possible.  
operation is not disc.  
possible.  
Noise and/or  
Press RESET. (Page  
The operation is This operation is  
other factors are 10)  
causing the built-  
in microproces-  
sor to operate in-  
correctly.  
not compatible  
with the config-  
uration of the  
disc.  
not possible.  
The image dis- The data could  
Stop playback  
once, and start  
Operation with Battery power is Load a new battery.  
played stops  
(pauses) and  
no longer be  
read during play- playback again.  
the unit cannot back.  
be operated.  
the remote  
control is not  
possible.  
low.  
Some operations Try operating with  
are prohibited  
with certain  
discs.  
another disc.  
The unit does  
not operate  
correctly even  
when the ap-  
propriate re-  
mote control  
buttons are  
pressed.  
There is no  
sound.  
The volume  
level is low.  
The volume level Adjust the volume  
is low. level.  
The attenuator is Turn the attenuator  
on.  
off.  
The sound and The unit is not  
Firmly secure the  
unit.  
video skip.  
firmly secured.  
File size and  
transmission rate that is within the  
are above recom- recommended size  
Create a DivX file  
Playback is not The disc is dirty. Clean the disc.  
possible.  
The type of disc Check the disc  
mended rates.  
and transmission  
rate.  
loaded cannot be type.  
played on this  
unit.  
The aspect  
ratio is incor-  
rect and the  
image is  
The aspect ratio Select the appro-  
setting is incor- priate setting for  
rect for the dis-  
play.  
The disc loaded Change the disc to  
is not compatible one that is compa-  
your display. (Page  
with this video  
system.  
tible with your  
video system.  
stretched.  
The motor  
sounds when  
the ignition  
switch is  
turned ON (or  
is turned to  
ACC).  
The unit is con-  
firming whether operation.  
or not a disc is  
This is a normal  
There is no  
sound.  
The volume  
level will not  
rise.  
Cables are not  
connected cor-  
rectly.  
Connect the cables  
correctly.  
loaded.  
The unit is per-  
forming still,  
slow motion or  
frame-by-frame  
playback.  
There is no sound  
during still, slow  
motion or frame-  
by-frame playback.  
69  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Symptom  
Cause  
Action (Refer-  
ence page)  
Symptom  
Cause  
Action (Refer-  
ence page)  
Nothing is dis- The rear view  
Connect a rear  
view camera.  
Dialog lan-  
guage (and  
subtitle lan-  
The DVD being  
played does not not be switched if  
feature multiple they are not re-  
The language can-  
played.  
camera is not  
connected.  
The touch  
panel keys can-  
not be used.  
guage) cannot language record- corded on the disc.  
Camera Polarity Press and hold  
be switched.  
ings.  
is at incorrect  
setting.  
MENU to return to  
the source display  
and then select the  
correct setting for  
Camera Polarity.  
You can only  
Switch the lan-  
switch between guage using the  
items indicated disc menu.  
in the disc menu.  
No subtitles  
The DVD being  
Subtitles are not  
No xxxx ap-  
pears when a  
display is chan- mation.  
ged (No Title,  
for example).  
There is no em-  
bedded text infor- or play another  
Switch the display  
are displayed. played does not displayed if they  
feature subtitles. are not recorded  
on the disc.  
track/file.  
You can only  
Switch the lan-  
switch between guage using the  
items indicated disc menu.  
in the disc menu.  
Sub-folders  
cannot be  
Folder repeat  
play has been se- range again.  
Select the repeat  
played back.  
lected.  
Playback is not The DVD being  
The language can-  
performed with played does not not be switched if  
the audio lan- feature dialog or the selected lan-  
The repeat  
Another folder  
Select the repeat  
range changes was selected dur- range again.  
automatically. ing repeat play.  
guage and sub- subtitles in the  
title language selected lan-  
guage is not re-  
corded on the disc.  
Track search or  
fast forward/re-  
verse was per-  
formed during  
file repeat play.  
Select the repeat  
range again.  
settings se-  
guage.  
lected in Video  
Setup menu.  
The viewing  
angle cannot  
be switched.  
The DVD being  
played does not cannot be  
feature scenes  
The viewing angle  
switched if the  
DVD  
shot from multi- DVD does not fea-  
ple angles.  
ture scenes re-  
corded from  
multiple angles.  
Symptom  
Cause  
Action (Refer-  
ence page)  
Playback is not The loaded disc Replace the disc  
possible. has a different re- with one featuring  
You are trying to Switch between  
switch to multi- multiple angles  
angle viewing for when watching  
a scene that was scenes recorded  
not recorded  
from multiple an- gles.  
gles.  
gion number  
from this unit.  
the same region  
number as this  
unit.  
from multiple an-  
A parental lock Parental lock is  
message is dis- activated.  
played and  
Turn parental lock  
off or change the  
playback is not  
possible.  
Parental lock  
The code number Enter the correct  
cannot be can- is incorrect.  
celed.  
code number.  
You have forgot- Press RESET. (Page  
ten your code  
number.  
70  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
Bluetooth audio/telephone  
Symptom  
Cause  
Action (Refer-  
ence page)  
Symptom  
Cause  
Action  
The image is  
extremely un-  
clear/distorted prohibit copying. the analog copy  
and dark dur-  
ing playback.  
Some discs fea- Since this unit is  
ture a signal to compatible with  
The sound  
from the Blue- progress on a  
tooth audio  
source is not  
played back.  
There is a call in The sound will be  
played back when  
the call is termi-  
nated.  
Bluetooth con-  
nected cellular  
phone.  
generation man-  
agement system,  
when playing a  
disc that has a sig-  
nal prohibiting  
copying, horizontal  
stripes or other im-  
perfections may  
appear when  
A Bluetooth-con- Do not operate the  
nected cellular  
phone is cur-  
rently being oper-  
ated.  
cellular phone at  
this time.  
A call was made Reconnect the  
with a Bluetooth- Bluetooth connec-  
connected cellu- tion between this  
viewed on some  
displays. This is  
not a malfunction.  
lar phone and  
unit and the cellu-  
then immediately lar phone.  
terminated. As a  
result, communi-  
cation between  
Video CD  
Symptom  
Cause  
Action  
this unit and the  
cellular phone  
was not termi-  
The PBC (play- The Video CD  
This operation is  
not available for  
back control)  
menu cannot  
be called up.  
being played  
does not feature Video CDs that do  
PBC.  
nated properly.  
not feature PBC.  
Repeat play  
The Video CD  
This operation is  
and track/time being played fea- not available for  
search are not tures PBC.  
possible.  
Video CDs that fea-  
ture PBC.  
Error messages  
When you contact your dealer or your nearest  
Pioneer Service Center, be sure to note the  
error message.  
iPod  
Symptom  
Cause  
Action  
The iPod does The cables are in- Disconnect the  
not operate  
correctly.  
correctly con-  
nected.  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
Tuner  
Message  
Cause  
Action  
No Data Pro- This unit cannot Move to the desir-  
vided  
receive artist  
name/song title good reception.  
information.  
able location with  
The iPod version Update the iPod  
is old. version.  
No Data  
This unit cannot Move to the desir-  
receive program able location with  
service name in- good reception.  
formation.  
DVD  
Message  
Cause  
Action  
Different Re- The disc does not Replace the DVD  
gion Disc  
have the same  
region number  
as this unit.  
with one bearing  
the correct region  
number.  
71  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Message  
Cause  
Action  
Message  
Cause  
Action  
Error-02-XX/  
FF-FF  
The disc is dirty. Clean the disc.  
Unplayable  
File  
This type of file  
cannot be played  
on this unit.  
Select a file that  
can be played.  
The disc is  
scratched.  
Replace the disc.  
Format Read/ Sometimes there Wait until the mes-  
The disc is  
loaded upside  
down.  
Check that the disc  
is loaded correctly.  
Ready  
is a delay be-  
sage disappears  
tween the start of and you hear  
playback and  
sound.  
There is an elec- Press RESET.  
trical or mechan-  
ical error.  
when you start to  
hear any sound.  
Video frame  
DivX files frame Select a file that  
Unplayable  
Disc  
This type of disc Replace the disc  
cannot be played with one that can  
on this unit.  
rate not sup- rate is more than can be played.  
ported. 30 fps.  
be played on this  
unit.  
Audio Format This type of file is Select a file that  
not sup-  
ported.  
not supported on can be played.  
this unit.  
The inserted disc Replace the disc.  
does not contain  
any playable  
files.  
External storage device (USB)  
Message  
Cause  
Action  
Protect  
Skipped  
TEMP  
All the files on  
the inserted disc  
are embedded  
with DRM.  
Replace the disc.  
Unplayable  
File  
This type of file  
cannot be played can be played.  
on this unit.  
Select a file that  
The inserted disc Play an audio file  
contains DRM  
protected files.  
There are no  
songs.  
Transfer the audio  
files to the USB  
portable audio  
player/USB mem-  
ory and connect.  
not embedded with  
Windows Media  
DRM 9/10.  
The temperature Wait until the unit  
of the unit is out- returns to a tem-  
side the normal perature within the  
operating range. normal operating  
limits.  
Security for the  
connected USB memory instruc-  
memory is en-  
abled.  
Follow the USB  
tions to disable se-  
curity.  
Rental Ex-  
pired.  
The inserted disc Select a file that  
contains expired can be played.  
DivX VOD con-  
Format Read/ Sometimes there Wait until the mes-  
Ready  
is a delay be-  
sage disappears  
tween the start of and you hear  
tent.  
playback and  
sound.  
when you start to  
hear any sound.  
Video resolu- The inserted disc Select a file that  
tion not sup- contains a high can be played.  
ported  
definition DivX  
file.  
Skipped  
The connected  
USB portable  
audio player/  
USB memory  
contains WMA  
files that are pro-  
tected by  
Play an audio file  
not embedded with  
Windows Media  
DRM 9/10.  
It is not possi- This units flash Select a file that  
ble to write it memory used as can be played.  
in the flash.  
the temporary  
storage area is  
full.  
Windows  
Mediaä  
DRM 9/10.  
Your device is This units DivX Register this unit  
not author-  
ized to play  
registration code to the DivX VOD  
has not been contents provider.  
this DivX pro- authorized by the  
tected video. DivX VOD con-  
tents provider.  
72  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
Message  
Cause  
Action  
Message  
Cause  
Action  
Transfer audio files  
not protected by  
Windows Media  
DRM 9/10 to the  
Rental Ex-  
pired.  
The inserted ex- Select a file that  
ternal storage de- can be played.  
vice contains  
Protect  
All the files on  
the connected  
USB portable  
audio player/  
expired DivX  
VOD content.  
USB memory are USB portable  
protected by audio player/USB  
Windows Media memory and con-  
DRM 9/10. nect.  
Video resolu- The inserted ex- Select a file that  
tion not sup- ternal storage de- can be played.  
ported  
vice contains a  
high definition  
DivX file.  
Incompatible The USB device Connect a USB  
USB  
connected to is  
portable audio  
not supported by player or USB  
It is not possi- This units flash Select a file that  
ble to write it memory used as can be played.  
this unit.  
memory that is  
USB Mass Storage  
Class compliant.  
in the flash.  
the temporary  
storage area is  
full.  
The USB device The connected  
is not formatted USB device should  
Your device is This units DivX Register this unit  
with FAT16 or  
FAT32.  
be formatted with  
FAT16 or FAT32.  
not author-  
ized to play  
this DivX pro-  
tected video.  
registration code to the DivX VOD  
has not been  
contents provider.  
authorized by the  
DivX VOD con-  
tents provider.  
Check USB  
The USB connec- Check that the  
tor or USB cable USB connector or  
has short-  
circuited.  
USB cable is not  
caught in some-  
thing or damaged.  
Format Read/ Sometimes there Wait until the mes-  
Ready  
is a delay be-  
tween the start of  
playback and  
sage disappears  
and you hear  
sound.  
The connected  
USB portable  
audio player/  
USB memory  
Disconnect the  
USB portable  
audio player/USB  
memory and do  
when you start to  
hear any sound.  
consumes more not use it. Turn the  
Video frame  
rate not sup- rate is more than can be played.  
ported. 30 fps.  
DivX files frame Select a file that  
than maximum  
allowable cur-  
rent.  
ignition switch to  
OFF, then to ACC  
or ON and then  
connect a compli-  
ant USB portable  
audio player/USB  
memory.  
Audio Format This type of file is Select a file that  
not sup-  
ported.  
not supported on can be played.  
this unit.  
iPod  
Error-02-9X/- Communication Perform one of the  
DX  
failed.  
following opera-  
tions.  
Message  
Cause  
Action  
Turn the ignition  
switch OFF and  
back ON.  
Format Read/ Sometimes there Wait until the mes-  
Ready is a delay be- sage disappears  
tween the start of and you hear  
Disconnect the  
USB portable  
audio player/USB  
memory.  
playback and  
when you start to  
hear any sound.  
sound.  
Change to a dif-  
ferent source.  
Then, return to the  
USB portable  
audio player/USB  
memory.  
73  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
Understanding messages  
Message  
Cause  
Action  
Error-02-6X/- Communication Disconnect the  
9X/-DX  
Messages  
Translation  
failed.  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
Pioneer recommends  
the use of a camera  
which outputs mirror-  
reversed images.  
Otherwise, the screen  
image will appear re-  
versed.  
CAUTION: Screen  
image may appear re-  
versed.  
iPod failure.  
Disconnect the  
cable from the  
iPod. Once the  
iPods main menu  
is displayed, recon-  
nect the iPod and  
reset it.  
Error-02-67  
Stop  
The iPod firm-  
ware version is  
old.  
Update the iPod  
version.  
There are no  
songs.  
Transfer songs to  
the iPod.  
There are no  
Select a list that  
songs in the cur- contains songs.  
rent list.  
Not Found  
No related  
songs.  
Transfer songs to  
the iPod.  
Bluetooth  
Message  
Cause  
Action  
Error-10  
The power failed Turn the ignition  
for the Bluetooth switch OFF and  
module of this  
unit.  
then to ACC or ON.  
If the error mes-  
sage is still dis-  
played after  
performing the  
above action,  
please contact  
your dealer or an  
authorized Pioneer  
Service Station.  
74  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Indicator list  
Shows when analog audio of HD  
Radio signal is received.  
Area 1  
Area 2  
Shows when digital audio of HD  
Radio signal is received.  
Shows when HD Radio station in-  
formation is received.  
Shows while searching a song/  
video in alphabet search mode.  
Shows which subtitle language  
has been selected.  
Area 3  
Shows which viewing angle has  
been selected.  
Area 1  
Indicates that the selected fre-  
quency is being broadcast in  
stereo.  
Shows which audio output has  
been selected.  
Indicates that the digital format is  
Dolby Digital.  
Area 2  
Indicates that the digital format is  
MPEG Audio.  
Shows the disc title of the CD text  
disc currently being played.  
Indicates that the digital format is  
Linear PCM.  
Shows the track title of the track cur-  
rently being played for CD text discs.  
Shows the song title of the song cur-  
rently being played for MP3/WMA/  
AAC files.  
Indicates the sampling frequency.  
Shows the comment currently being  
played.  
Indicates that the digital format is  
DTS.  
Shows the station name currently  
tuned in to.  
Shows the artist name of the track/  
song currently being played for CD  
text discs.  
1+1ch  
Indicates the audio channel.  
Shows the artist name of the artist  
currently being played for MP3/  
WMA/AAC files.  
2ch  
Mch  
Shows the category name.  
Indicates that a disc with PBC On  
is being played.  
Shows the folder name of the folder  
containing the MP3/WMA/AAC file  
currently being played.  
Shows when HD Radio signal is re-  
ceived.  
75  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Handling guidelines  
Discs and player  
Shows the file name of the MP3/  
WMA/AAC file currently being  
played.  
Use only discs featuring any of following logos.  
Shows the preset number of the sta-  
tion currently being tuned in to.  
Shows SIRIUS information.  
Area 3  
Shows the title number currently  
being played.  
Shows the chapter number cur-  
rently being played.  
Use 12-cm discs. Do not use 8-cm discs or an adapter  
for 8-cm discs.  
Shows the replay time currently  
being played.  
Use only conventional, fully circular discs. Do not use  
shaped discs.  
Shows when the game alert func-  
tion is on while receiving SIRIUS  
stations.  
Indicates that the feature demo is  
on.  
Do not insert anything other than a DVD (-R/-RW) or  
CD (-R/-RW) into the disc loading slot.  
Do not use cracked, chipped, warped, or otherwise  
damaged discs as they may damage the player.  
Unfinalized CD-R/CD-RW discs cannot be played  
back.  
Do not touch the recorded surface of the discs.  
Store discs in their cases when not in use.  
Do not attach labels, write on or apply chemicals to  
the surface of the discs.  
To clean a disc, wipe the disc with a soft cloth out-  
ward from the center.  
Condensation may temporarily impair the players  
performance. Let it rest for about one hour to adjust  
to a warmer temperature. Also, wipe any damp discs  
off with a soft cloth.  
Playback of discs may not be possible because of  
disc characteristics, disc format, recorded applica-  
tion, playback environment, storage conditions, and  
so on.  
Road shocks may interrupt disc playback.  
76  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
iPod  
Read the precautions for discs before using them.  
Certain functions may not be available for some DVD  
video discs.  
To ensure proper operation, connect the dock connec-  
tor cable from the iPod directly to this unit.  
It may not be possible to play back some DVD video  
discs.  
Firmly secure the iPod when driving. Do not let the  
iPod fall onto the floor, where it may become jammed  
under the brake or accelerator pedal.  
It is not possible to play back DVD-RAM discs.  
About iPod settings  
This unit is not compatible with discs recorded in  
AVCHD (Advanced Video Codec High Definition) for-  
mat. Do not insert AVCHD discs as you may not be  
able to eject the disc.  
!
When an iPod is connected, this unit changes the  
EQ (equalizer) setting of the iPod to off in order to  
optimize the acoustics. When you disconnect the  
iPod, the EQ returns to the original setting.  
!
You cannot set Repeat to off on the iPod when  
using this unit. Repeat is automatically changed  
to All when the iPod is connected to this unit.  
External storage device (USB)  
Depending on the external storage device (USB), the  
following problems may occur.  
Incompatible text saved on the iPod will not be dis-  
played by the unit.  
!
!
!
Operations may vary.  
The storage device may not be recognized.  
Files may not be played back properly.  
DVD-R/DVD-RW discs  
Unfinalized DVD-R/-RW discs which have been re-  
corded in the Video format (video mode) cannot be  
played back.  
Playback of DVD-R/DVD-RW discs may not be possi-  
ble, due to disc characteristics, scratches or dirt on  
the disc, or dirt, condensation, etc. on the lens of this  
unit.  
USB storage device  
Connections via USB hub are not supported.  
Do not connect anything other than a USB storage  
device.  
Depending on the application settings and the envir-  
onment, playback of discs recorded on a personal  
computer may not be possible. (For details, contact  
the manufacturer of the application.)  
Firmly secure the USB storage device when driving.  
Do not let the USB storage device fall onto the floor,  
where it may become jammed under the brake or ac-  
celerator pedal.  
Depending on the USB storage device, the device  
may cause noise to occur in the radio.  
CD-R/CD-RW discs  
When CD-R/CD-RW discs are used, playback is possi-  
ble only for discs which have been finalized.  
Playback of CD-R/CD-RW discs recorded on a music  
CD recorder or a personal computer may not be pos-  
sible due to disc characteristics, scratches or dirt on  
the disc, or dirt, condensation, etc., on the lens of this  
unit.  
Depending on the application settings and the envir-  
onment, playback of discs recorded on a personal  
computer may not be possible. (For details, contact  
the manufacturer of the application.)  
Copyright protected files that are stored in the USB  
devices cannot be played back.  
You cannot connect a USB portable audio player/USB  
memory to this unit via USB hub.  
Partitioned USB memory is not compatible with this  
unit.  
Depending on the kind of USB portable audio player/  
USB memory you use, the device may not be recog-  
nized or audio files may not be played back properly.  
Playback of CD-R/CD-RW discs may become impossi-  
ble in case of direct exposure to sunlight, high tem-  
peratures, or the storage conditions in the vehicle.  
Titles and other text information recorded on a CD-R/  
CD-RW disc may not be displayed by this unit (in the  
case of audio data (CD-DA)).  
Do not leave the USB portable audio player/USB  
memory in direct sunlight for extended amounts of  
time. Doing so may cause the device to malfunction  
from the extreme rise in temperature.  
77  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
DualDiscs  
The ID code of this unit must be registered to a DivX  
VOD provider in order to playback DivX VOD files. For  
information on ID codes, refer to Displaying the DivXâ  
DualDiscs are two-sided discs that have a recordable  
CD for audio on one side and a recordable DVD for  
video on the other.  
Playback of the DVD side is possible with this unit.  
However, since the CD side of DualDiscs is not physi-  
cally compatible with the general CD standard, it may  
not be possible to play the CD side with this unit.  
Frequent loading and ejecting of a DualDisc may re-  
sult in scratches on the disc. Serious scratches can  
lead to playback problems on this unit. In some  
cases, a DualDisc may become stuck in the disc load-  
ing slot and will not eject. To prevent this, we recom-  
mend you refrain from using DualDisc with this unit.  
Please refer to the information from the disc manu-  
facturer for more detailed information about  
DualDiscs.  
For more details about DivX, visit the following site:  
Important  
!
When naming a JPEG image file, add the cor-  
responding filename extension (.jpg, .jpeg, .  
jpe or.jfif).  
!
This unit plays back files with these filename  
extensions (.jpg, .jpeg, .jpe or .jfif) as a JPEG  
image file. To prevent malfunctions, do not  
use these extensions for files other than JPEG  
image files.  
JPEG picture files  
JPEG is short for Joint Photographic Experts Group  
and refers to a still image compression technology  
standard.  
Compressed audio  
compatibility (disc, USB)  
WMA  
Files are compatible with Baseline JPEG and EXIF 2.1  
still images up to a resolution of 8 192 × 7 680. (EXIF  
format is used most commonly with digital still cam-  
eras.)  
File extension: .wma  
Playback of EXIF format files that were processed by a  
personal computer may not be possible.  
Bit rate: 5 kbps to 320 kbps (CBR), VBR  
Sampling frequency: 8 kHz to 48 kHz  
There is no progressive JPEG compatibility.  
Windows Media Audio Professional, Lossless, Voice/  
DRM Stream/Stream with video: Not compatible  
DivX video files  
Depending on the composition of the file information,  
such as the number of audio streams or file size,  
there may be a slight delay when playing back discs.  
MP3  
File extension: .mp3  
Some special operations may be prohibited due to  
the composition of the DivX files.  
Bit rate: 8 kbps to 320 kbps (CBR), VBR  
Sampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz,  
48 kHz for emphasis)  
Only DivX files downloaded from a DivX partner site  
are guarantee for proper operation. Unauthorized  
DivX files may not operate properly.  
Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3 (ID3 tag  
Version 2.x is given priority over Version 1.x.)  
DRM rental files cannot be operated until playback is  
started.  
M3u playlist: Not compatible  
MP3i (MP3 interactive), mp3 PRO: Not compatible  
Recommended file size: 2 Mbps or less with a trans-  
mission rate of 4 GB or less.  
AAC  
Compatible format: AAC encoded by iTunes  
File extension: .m4a  
78  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Sampling frequency: 8 kHz to 44.1 kHz  
Bit rate: 8 kbps to 320 kbps  
Packet write data transfer: Not compatible  
Regardless of the length of blank sections between  
the songs from the original recording, compressed  
audio discs play with a short pause between songs.  
Apple Lossless: Not compatible  
AAC file bought from the iTunes Store (.m4p file ex-  
tension): Not compatible  
External storage device (USB)  
Playable folders: up to 6 000 (up to 700 for DivX)  
Playable files: up to 65 535, up to 255 for one folder  
Playback of copyright-protected files: Not compatible  
DivX compatibility  
Compatible format: DivX video format implemented in  
relation to DivX standards  
File extensions: .avi or .divx  
Partitioned external storage device (USB): Only the  
first playable partition can be played.  
DivX Ultra format: Not compatible  
DivX HD format: Not compatible  
There is no compatibility for Multi Media Cards  
(MMC).  
DivX files without video data: Not compatible  
DivX plus: Not compatible  
CAUTION  
Compatible audio codec: MP2, MP3, Dolby Digital  
LPCM: Not compatible  
!
!
Pioneer accepts no responsibility for data lost  
on the USB memory/USB portable audio  
player even if that data is lost while using this  
unit.  
Do not leave the discs/external storage device  
(USB) or iPod in places with high  
temperatures.  
Bit rate: 8 kbps to 320 kbps (CBR), VBR  
Sampling frequency: 8 kHz to 48 kHz  
Compatible external subtitle file extension: .srt  
Supplemental information  
Some characters in a file name (including the file ex-  
tension) or a folder name may not be displayed.  
This unit may not operate correctly depending on the  
application used to encode WMA files.  
There may be a slight delay at the start of playback of  
audio files embedded with image data or audio files  
stored on a USB storage device that has numerous  
folder hierarchies.  
Disc  
Playable folders: up to 700  
Playable files: up to 999 for CD-R/CD-RW  
Playable files: up to 3 500 for DVD-R/DVD-RW  
File system: ISO 9660 Level 1 and 2, Romeo, Joliet,  
UDF 1.02, 1.50, 2.00, 2.01, 2.50 (DVD-R/DVD-RW)  
Multi-session playback: Compatible  
79  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
Example of a hierarchy  
iPod compatibility  
01  
02  
This unit supports only the following iPod models.  
Supported iPod software versions are shown below.  
Older versions may not be supported.  
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
iPhone 4 (software version 4.1)  
iPhone 3GS (software version 4.1)  
iPhone 3G (software version 4.1)  
iPhone (software version 3.1.3)  
03  
: Folder  
: Compressed  
audio file  
01 to 05: Folder  
number  
1 to 6: Playback  
sequence  
04  
iPod nano 6th generation (software version 1.0)  
iPod nano 5th generation (software version 1.0.2)  
iPod nano 4th generation (software version 1.0.4)  
iPod nano 3rd generation (software version 1.1.3)  
iPod nano 2nd generation (software version 1.1.3)  
iPod nano 1st generation (software version 1.3.1)  
iPod touch 4th generation (software version 4.1)  
iPod touch 3rd generation (software version 4.0)  
iPod touch 2nd generation (software version 4.0)  
iPod touch 1st generation (software version 3.1.3)  
iPod classic 160GB (software version 2.0.4)  
iPod classic 120GB (software version 2.0.1)  
iPod classic (software version 1.1.2)  
05  
Level 1 Level 2 Level 3 Level 4  
Disc  
Folder selection sequence or other operation  
may differ depending on the encoding or writ-  
ing software.  
External storage device (USB)  
The playback sequence is the same as the re-  
corded sequence in the external storage de-  
vice (USB).  
To specify the playback sequence, the follow-  
ing method is recommended.  
1 Create a file name that includes numbers that  
specify the playback sequence (e.g., 001xxx.  
mp3 and 099yyy.mp3).  
iPod 5th generation (software version 1.3)  
Depending on the generation or version of the iPod,  
some functions may not be available.  
Operations may vary depending on the software ver-  
sion of iPod.  
When using an iPod, an iPod Dock Connector to USB  
Cable is required.  
2 Put those files into a folder.  
When you use Pioneer CD-IU50V/CD-IU200V interface  
cable, consult your dealer for details.  
3 Save the folder that contains the files to the  
external storage device (USB).  
However, depending on the system environ-  
ment, you may not be able to specify the play-  
back sequence.  
About the file/format compatibility, refer to the iPod  
manuals.  
Audio Book, Podcast: Compatible  
For USB portable audio players, the sequence  
is different and depends on the player.  
CAUTION  
Pioneer accepts no responsibility for data lost on  
the iPod, even if that data is lost while this unit is  
used.  
Using the display correctly  
CAUTION  
!
If liquid or foreign matter should get inside  
this unit, turn off the power immediately and  
consult your dealer or the nearest authorized  
PIONEER Service Station. Do not use the unit  
in this condition because doing so may result  
in fire, electric shock, or other failure.  
Sequence of audio files  
The user cannot assign folder numbers and  
specify playback sequences with this unit.  
80  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
!
!
If you notice smoke, a strange noise or smell,  
or any other abnormal signs from the display,  
turn off the power immediately and consult  
your dealer or the nearest authorized  
PIONEER Service Station. Using this unit in  
this condition may result in permanent da-  
mage to the system.  
Do not disassemble or modify this unit, as  
there are high-voltage components inside  
which may cause electric shock. Be sure to  
consult your dealer or the nearest authorized  
PIONEER Service Station for internal inspec-  
tion, adjustments, or repairs.  
due to the characteristics of the LCD  
screen and do not indicate a malfunction.  
When using a cellular phone, keep the an-  
tenna away from the display to prevent dis-  
ruption of the video image by the  
!
appearance of spots, colored stripes, etc.  
LED (light-emitting diode)  
backlight  
!
At low temperatures, using the LED back-  
light may increase image lag and degrade  
the image quality due to the characteristics  
of the LCD screen. Image quality will im-  
prove with an increase in temperature.  
To protect the LED backlight, the display  
will darken in the following environments:  
In the direct sunlight  
Handling the display  
!
!
Never touch the screen with anything be-  
sides your finger when operating the touch  
panel function. The screen can scratch ea-  
sily.  
When the display is subjected to direct sun-  
light for a long period of time, it will be-  
come very hot resulting in possible  
damage to the LCD screen. You should  
avoid exposing the display unit to direct  
sunlight as much as possible.  
Near the heater vent  
!
!
The product lifetime of the LED backlight is  
more than 10 000 hours. However, it may  
decrease if used in high temperatures.  
If the LED backlight reaches the end of its  
product lifetime, the screen will become  
dark and the image will no longer be pro-  
jected. In such cases, please consult your  
dealer or the nearest authorized PIONEER  
Service Station.  
!
!
The display should be used within the tem-  
perature range of 10°C to +60°C (14 °F to  
140 °F).  
At temperatures higher or lower than this  
operating temperature range, the display  
may not operate normally.  
The LCD screen is exposed in order to in-  
crease its visibility within the vehicle. Do  
not press it strongly on it as this may da-  
mage it.  
Keeping the display in good  
condition  
!
!
!
When removing dust from the screen or  
cleaning the display, first turn the system  
power off, then wipe with a soft dry cloth.  
When wiping the screen, take care not to  
scratch the surface. Do not use harsh or  
abrasive chemical cleaners.  
!
Do not push the LCD screen forcefully as  
this may scratch it.  
Liquid crystal display (LCD) screen  
!
Heat from the heater may damage the LCD  
screen, and cool air from the cooler may  
cause moisture to form inside the display  
resulting in possible damage.  
!
Small black dots or white dots (bright dots)  
may appear on the LCD screen. These are  
81  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
iPhone, respectively, and has been certified by  
the developer to meet Apple performance  
standards.  
Apple is not responsible for the operation of  
this device or its compliance with safety and  
regulatory standards.  
Please note that the use of this accessory with  
iPod or iPhone may affect wireless perfor-  
mance.  
Copyright and trademark  
This item incorporates copy protection tech-  
nology that is protected by U.S. patents and  
other intellectual property rights of Rovi  
Corporation. Reverse engineering and disas-  
sembly are prohibited.  
DVD video  
is a trademark of DVD Format/Logo  
Licensing Corporation.  
Dolby Digital  
Manufactured under license from Dolby  
Laboratories. Dolbyand the double-D symbol  
are trademarks of Dolby Laboratories.  
iTunes  
Apple and iTunes are trademarks of Apple  
Inc., registered in the U.S. and other coun-  
tries.  
DivX  
DivXâ, DivX Certifiedâ and associated logos  
are trademarks of DivX, Inc. and are used  
under license.  
MP3  
Supply of this product only conveys a license  
for private, non-commercial use and does not  
convey a license nor imply any right to use  
this product in any commercial (i.e. revenue-  
generating) real time broadcasting (terrestrial,  
satellite, cable and/or any other media), broad-  
casting/streaming via internet, intranets and/  
or other networks or in other electronic con-  
tent distribution systems, such as pay-audio or  
audio-on-demand applications. An indepen-  
dent license for such use is required. For de-  
tails, please visit  
ABOUT DIVX VIDEO: DivXâ is a digital  
video format created by DivX, Inc. This is an of-  
ficial DivX Certifiedâ device that plays DivX  
video. Visit divx.com for more information and  
software tools to convert your files into DivX  
video.  
ABOUT DIVX VIDEO-ON-DEMAND: This  
DivX Certifiedâ device must be registered in  
order to play purchased DivX Video-on-De-  
mand (VOD) movies. To obtain your registra-  
tion code, locate the DivX VOD section in  
Displaying the DivXâ VOD registration code. Go  
to vod.divx.com for more information on how  
to complete your registration.  
WMA  
Windows Media is either a registered trade-  
mark or trademark of Microsoft Corporation in  
the United States and/or other countries.  
This product includes technology owned by  
Microsoft Corporation and cannot be used or  
distributed without a license from Microsoft  
Licensing, Inc.  
About the SAT RADIO READY mark  
iPod & iPhone  
iPhone, iPod, iPod classic, iPod nano, and  
iPod touch are trademarks of Apple Inc., regis-  
tered in the U.S. and other countries.  
Made for iPodand Made for iPhonemean  
that an electronic accessory has been de-  
signed to connect specifically to iPod or  
82  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
The SAT RADIO READY mark indicates that  
the Satellite Radio Tuner for Pioneer (i.e., XM  
tuner and Sirius satellite tuner which are sold  
separately) can be controlled by this unit.  
Please inquire to your dealer or nearest  
authorized Pioneer service station regarding  
the satellite radio tuner that can be connected  
to this unit. For satellite radio tuner operation,  
please refer to the satellite radio tuner owners  
manual.  
!
The system will use direct satellite-to-recei-  
ver broadcasting technology to provide lis-  
teners in their cars and at home with  
crystal-clear sound seamlessly from coast  
to coast. Satellite radio will create and  
package over 100 channels of digital-quality  
music, news, sports, talk and childrens  
programming.  
!
SAT Radio, the SAT Radio logo and all re-  
lated marks are trademarks of Sirius Satel-  
lite Radio Inc., and XM Satellite Radio Inc.  
HD Radioä Technology  
HD Radioä, HD Radio Readyä, and the HD  
Radio Ready logo are proprietary trademarks  
of iBiquity Digital Corporation.  
This HD Radio Ready receiver is ready to re-  
ceive HD Radio broadcasts when connected  
to the HD Radio tuner (e.g. GEX-P20HD), sold  
separately.  
83  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Appendix  
Additional Information  
Language code chart for DVD  
Language (code), input code  
Japanese (ja), 1001  
English (en), 0514  
French (fr), 0618  
Spanish (es), 0519  
German (de), 0405  
Italian (it), 0920  
Chinese (zh), 2608  
Dutch, Flemish (nl), 1412  
Portuguese (pt), 1620  
Swedish (sv), 1922  
Russian (ru), 1821  
Korean (ko), 1115  
Greek (el), 0512  
Dzongkha (dz), 0426  
Ewe (ee), 0505  
Kurdish (ku), 1121  
Komi (kv), 1122  
Cornish (kw), 1123  
Kirghiz, Kyrgyz (ky), 1125  
Latin (la), 1201  
Luxembourgish (lb), 1202  
Ganda (lg), 1207  
Limburgan (li), 1209  
Lingala (ln), 1214  
Kinyarwanda (rw), 1823  
Sanskrit (sa), 1901  
Sardinian (sc), 1903  
Sindhi (sd), 1904  
Northern Sami (se), 1905  
Sangho (sg), 1907  
Sinhala (si), 1909  
Slovak (sk), 1911  
Slovenian (sl), 1912  
Samoan (sm), 1913  
Shona (sn), 1914  
Somali (so), 1915  
Albanian (sq), 1917  
Serbian (sr), 1918  
Swati (ss), 1919  
Esperanto (eo), 0515  
Estonian (et), 0520  
Basque (eu), 0521  
Persian (fa), 0601  
Fulah (ff), 0606  
Finnish (fi), 0609  
Fijian (fj), 0610  
Faroese (fo), 0615  
Western Frisian (fy), 0625  
Irish (ga), 0701  
Gaelic (gd), 0704  
Galician (gl), 0712  
Guarani (gn), 0714  
Gujarati (gu), 0721  
Manx (gv), 0722  
Hausa (ha), 0801  
Hebrew (he), 0805  
Hindi (hi), 0809  
Hiri Motu (ho), 0815  
Croatian (hr), 0818  
Haitian (ht), 0820  
Hungarian (hu), 0821  
Armenian (hy), 0825  
Herero (hz), 0826  
Interlingua (ia), 0901  
Indonesian (id), 0904  
Interlingue (ie), 0905  
Igbo (ig), 0907  
Lao (lo), 1215  
Lithuanian (lt), 1220  
Luba-Katanga (lu), 1221  
Latvian (lv), 1222  
Malagasy (mg), 1307  
Marshallese (mh), 1308  
Maori (mi), 1309  
Macedonian (mk), 1311  
Malayalam (ml), 1312  
Mongolian (mn), 1314  
Marathi (mr), 1318  
Malay (ms), 1319  
Maltese (mt), 1320  
Burmese (my), 1325  
Nauru (na), 1401  
Bokmal (nb), 1402  
Ndebele, North (nd), 1404  
Nepali (ne), 1405  
Ndonga (ng), 1407  
Nynorsk (nn), 1414  
Norwegian (no), 1415  
Ndebele, South (nr), 1418  
Afar (aa), 0101  
Abkhazian (ab), 0102  
Avestan (ae), 0105  
Afrikaans (af), 0106  
Akan (ak), 0111  
Amharic (am), 0113  
Aragonese (an), 0114  
Arabic (ar), 0118  
Sotho, Southern (st), 1920  
Sundanese (su), 1921  
Swahili (sw), 1923  
Tamil (ta), 2001  
Telugu (te), 2005  
Tajik (tg), 2007  
Assamese (as), 0119  
Avaric (av), 0122  
Thai (th), 2008  
Tigrinya (ti), 2009  
Turkmen (tk), 2011  
Tagalog (tl), 2012  
Tswana (tn), 2014  
Tonga (to), 2015  
Turkish (tr), 2018  
Tsonga (ts), 2019  
Tatar (tt), 2020  
Aymara (ay), 0125  
Azerbaijani (az), 0126  
Bashkir (ba), 0201  
Belarusian (be), 0205  
Bulgarian (bg), 0207  
Bihari (bh), 0208  
Bislama (bi), 0209  
Bambara (bm), 0213  
Bengali (bn), 0214  
Tibetan (bo), 0215  
Breton (br), 0218  
Sichuan Yi (ii), 0909  
Inupiaq (ik), 0911  
Ido (io), 0915  
Icelandic (is), 0919  
Inuktitut (iu), 0921  
Javanese (jv), 1022  
Georgian (ka), 1101  
Kongo (kg), 1107  
Twi (tw), 2023  
Navajo, Navaho (nv), 1422 Tahitian (ty), 2025  
Chichewa (ny), 1425  
Occitan (oc), 1503  
Ojibwa (oj), 1510  
Oromo (om), 1513  
Oriya (or), 1518  
Ossetian (os), 1519  
Panjabi, Punjabi (pa),  
1601  
Uighur, Uyghur (ug), 2107  
Ukrainian (uk), 2111  
Urdu (ur), 2118  
Uzbek (uz), 2126  
Venda (ve), 2205  
Vietnamese (vi), 2209  
Bosnian (bs), 0219  
Catalan (ca), 0301  
Chechen (ce), 0305  
Chamorro (ch), 0308  
Corsican (co), 0315  
Kikuyu, Gikuyu (ki), 1109  
Volapük (vo), 2215  
Cree (cr), 0318  
Czech (cs), 0319  
Church Slavic (cu), 0321  
Chuvash (cv), 0322  
Welsh (cy), 0325  
Kuanyama (kj), 1110  
Kazakh (kk), 1111  
Kalaallisut (kl), 1112  
Central Khmer (km), 1113  
Kannada (kn), 1114  
Pali (pi), 1609  
Walloon (wa), 2301  
Wolof (wo), 2315  
Xhosa (xh), 2408  
Yiddish (yi), 2509  
Yoruba (yo), 2515  
Zhuang, Chuang (za),  
2601  
Polish (pl), 1612  
Pashto, Pushto (ps), 1619  
Quechua (qu), 1721  
Romansh (rm), 1813  
Danish (da), 0401  
Kanuri (kr), 1118  
Rundi (rn), 1814  
Divehi (dv), 0422  
Kashmiri (ks), 1119  
Romanian (ro), 1815  
Zulu (zu), 2621  
84  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Specifications  
Phase .................................. Normal/Reverse  
Bass boost:  
Gain ...................................... +12 dB to 0 dB  
General  
Power source ............................. 14.4 V DC (10.8 V to 15.1 V  
allowable)  
DVD Player  
System .......................................... DVD video, Video CD, CD,  
WMA, MP3, AAC, DivX,  
Grounding system ................... Negative type  
Maximum current consumption  
..................................................... 10.0 A  
Dimensions (W × H × D):  
D
Chassis ..................... 178 mm × 100 mm ×  
165 mm  
(7 in. × 3-7/8 in. × 6-1/2 in.)  
Nose ........................... 171 mm × 97 mm × 7 mm  
(6-3/4 in.× 3-7/8 in.× 1/4 in.)  
Weight .......................................... 1.7 kg (3.7 lbs)  
JPEG player  
Usable discs .............................. DVD video, Video CD, CD,  
CD-R/RW, DVD-R/RW/R DL  
Region number ........................ 1  
Frequency response ............... 5 Hz to 44 000 Hz (with DVD,  
at sampling frequency  
96 kHz)  
Signal-to-noise ratio ............... 96 dB (1 kHz) (IHF-A net-  
work) (RCA level)  
Output level:  
Video .................................... 1.0 Vp-p/75 W ( 0.2 V)  
Number of channels .............. 2 (stereo)  
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3  
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12  
(2 ch audio)  
(Windows Media Player)  
AAC decoding format ............ MPEG-4 AAC (iTunes en-  
coded only) (.m4a)  
Display  
Screen size/aspect ratio ....... 5.8 inch wide/16:9  
(effective display area:  
128.4 mm × 70.9 mm)  
Pixels ............................................. 345 600 (1 440 × 240)  
Display method ........................ TFT active matrix, driving  
type  
Color system .............................. NTSC/PAL/PAL-M/PAL-N/  
SECAM compatible  
(Ver. 9.0.3 and earlier)  
DivX decoding format ............ Home Theater Ver. 3, 4, 5.2,  
6 (.avi, .divx)  
Durable temperature range (power off)  
..................................................... 20 °C to +80 °C  
USB  
Audio  
USB standard specification  
Maximum power output ....... 50 W × 4  
70 W × 1/2 W (for subwoo-  
fer)  
Continuous power output ... 22 W × 4 (50 Hz to  
15 000 Hz, 5 % THD,  
4 W load, both channels dri-  
ven)  
Load impedance ...................... 4 W (4 W to 8 W (2 W for 1 ch)  
allowable)  
..................................................... USB 1.1, USB 2.0 full speed  
Maximum current supply .... 500 mA  
USB Class ................................... MSC (Mass Storage Class)  
File system .................................. FAT16, FAT32  
MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3  
WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12  
(2 ch audio)  
(Windows Media Player)  
AAC decoding format ............ MPEG-4 AAC (iTunes en-  
coded only)  
(Ver. 9.0.3 and earlier)  
DivX decoding format ............ Home Theater Ver. 3, 4, 5.2,  
6 (.avi, .divx)  
Preout maximum output level  
..................................................... 2.0 V  
Equalizer (5-Band Graphic Equalizer):  
Frequency .......................... 100 Hz/315 Hz/1.25 kHz/  
3.15 kHz/8 kHz  
Gain ...................................... 12 dB  
High pass filter:  
Frequency .......................... 50 Hz/63 Hz/80 Hz/100 Hz/  
125 Hz  
Slope .................................... 12 dB/oct  
Subwoofer (mono):  
FM tuner  
Frequency range ...................... 87.9 MHz to 107.9 MHz  
Usable sensitivity ..................... 9 dBf (0.8 µV/75 W, mono,  
S/N: 30 dB)  
Signal-to-noise ratio ............... 72 dB (IHF-A network)  
Frequency .......................... 50 Hz/63 Hz/80 Hz/100 Hz/  
125 Hz  
Slope .................................... 18 dB/oct  
Gain ...................................... +6 dB to 24 dB  
AM tuner  
Frequency range ...................... 530 kHz to 1 710 kHz  
(10 kHz)  
85  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Appendix  
Additional Information  
Usable sensitivity ..................... 25 µV (S/N: 20 dB)  
Signal-to-noise ratio ............... 62 dB (IHF-A network)  
CEA2006 Specifications  
Power output ............................. 14 W RMS × 4 Channels  
(4 W and 1 % THD+N)  
S/N ratio ....................................... 91 dBA (reference: 1 W into  
4 W)  
Note  
Specifications and the design are subject to mod-  
ifications without notice.  
86  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
87  
En  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PIONEER CORPORATION  
1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,  
Kanagawa 212-0031, JAPAN  
PIONEER ELECTRONICS (USA) INC.  
P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.  
TEL: (800) 421-1404  
PIONEER EUROPE NV  
Haven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/Belgique  
TEL: (0) 3/570.05.11  
PIONEER ELECTRONICS ASIACENTRE PTE. LTD.  
253 Alexandra Road, #04-01, Singapore 159936  
TEL: 65-6472-7555  
PIONEER ELECTRONICS AUSTRALIA PTY. LTD.  
5 Arco Lane, Heatherton, Victoria, 3202 Australia  
TEL: (03) 9586-6300  
PIONEER ELECTRONICS OF CANADA, INC.  
300 Allstate Parkway, Markham, Ontario L3R 0P2, Canada  
TEL: 1-877-283-5901  
TEL: 905-479-4411  
PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.  
Blvd.Manuel Avila Camacho 138 10 piso  
Col.Lomas de Chapultepec, Mexico, D.F. 11000  
TEL: 55-9178-4270  
 
台北4078  
(02) 2657-3588  
司  
 
9901-6  
Published by Pioneer Corporation.  
Copyright ã 2010 by Pioneer Corporation.  
All rights reserved.  
(0852) 2848-6488  
Printed in Thailand  
<KKMZX> <10L00000>  
<CRB3537-B/N> UC  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pentax Camcorder ZX L User Manual
Philips Car Stereo System CE150 User Manual
Philips Projector LC4331 User Manual
Philips Telephone SJA9190 17 User Manual
Philips Work Light T20 User Manual
Pioneer Bluetooth Headset BDP LX70A User Manual
Pioneer Car Stereo System DEH 1650 User Manual
Pioneer Speaker VSX D509S User Manual
Poulan Lawn Mower PR25PH48STB User Manual
Pride Mobility Mobility Aid Jazzy 1170XL User Manual