VRZ222 layout 4/8/99 10:18 PM Page 1
Video Cassette Recorder
TM
VRZ222AT
O wner’s Manual
I M P O R T A N T !
Return Your W arranty Registration Card
W ithin 10 Days. See W hy Inside.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:18 PM Page 3
Introduction 3
W elcom e to your VCR owner’s m anual.
This manual has six sections: Setting Up Your VCR; Description of Controls; Basic Operations; Recording;
Playing; and Information You May Need. The instructions explain all of the VCR’s features, which are listed
below. You cannot hurt your VCR by trying the features! So read on – and relax.
Features
• High Quality (HQ) System
• Automatic Channel Setup
• On-Screen Displays in English or Spanish
• Display Panel
• Digital Auto Tracking System
• One-Touch Recording
• Timer Recording
• Special Effects Playback: Forward and Reverse Searching; Still
• Remote Control with capability to operate TV
• Repeat Play
• Automatic Operation Features
• Real-Time Counter
• Daylight-Saving Time
• The VCR Plus+ Programming System
• Automatic Head Cleaner
Safety Precautions
W arning: To prevent fire or shock hazard, do not expose
this equipm ent to rain or m oisture.
Federal Com m unications Com m ission W arning: Any
unauthorized changes or m odifications to this equipm ent
void the user’s authority to operate it.
This VCR is equipped with a High Quality (HQ) system and is
compatible with existing Video Home System (VHS) equipment.
Philips Consumer Electronics Company recommends that you use
only video cassette tapes that have been tested and inspected for
use in two, four, six, and eight hour VCRs, and which are labeled
with the
mark. The use of tapes that have not been inspected
for use in two, four, six, and eight hour VCRs may result in poor
picture quality and excessive deposits on the video heads, which
may not be covered by the warranty if damage occurs.
Note to the Cable TV System Installer: This reminder is
provided to call the Cable TV system installer’s attention to
Article 820-40 of the National Electrical Code, which provides
guidelines for proper grounding – in particular, specifying that the
cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as possible.
Copyright 1998 Philips Consumer Electronics Company. All rights
TM
®
reserved. VCR Plus+ and PlusCode are trademarks of Gemstar
Development Corporation. The VCR Plus+ Programming system
is manufactured under license from Gemstar Development
Corporation.
om
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:18 PM Page 4
4 Table of Contents
Setting Up Your VCR
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Before Using Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Hookups Without a Cable Box/Direct Broadcast System . . . . . . . . . . . . . . . . . . . . .6 - 7
Hookups With a Cable Box/Direct Broadcast System . . . . . . . . . . . . . . . . . . . . . . . .8 - 9
Hookups With a Stereo TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Turning on Your VCR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Automatic Channel Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12 - 14
Setting the Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Daylight-Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Language Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Description of Controls
Remote Control Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 - 19
On-Screen Status Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
VCR Display Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Basic O perations
Playing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Recording
Recording One Channel/Watching Another . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
One Touch Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Timer Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28 - 31
Setting Up the VCR Plus+ Programming System . . . . . . . . . . . . . . . . . . . . . . . . . .32 - 33
Timer Recording With the VCR Plus+ Programming System . . . . . . . . . . . . . . . . .34 - 35
Rerecording (Tape Duplication) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Playing
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37
Real-Time Counter Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
Special Effects Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
Automatic Operation Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
Inform ation You May Need
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41
Helpful Hints . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 - 43
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44
Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46
Supplied Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:18 PM Page 5
Before Using Your VCR 5
Rem oving the Plastic Cover from the Front Panel
A thin, plastic cover may protect the front panel of your VCR.
Before using the VCR, lift a corner of the plastic, then peel it off.
Putting Batteries in the Rem ote Control
1
1
Rem ove the battery com partm ent lid on the bottom of the
remote control by sliding it in the direction of the arrow.
2
3
2
Place two AA batteries inside the battery com partm ent
with their and ends aligned as indicated.
+
–
3
Replace the battery com partm ent lid.
Using the Rem ote Control
● Point the remote control at the VCR, then press the VCR but-
ton, when using the remote control to operate the VCR.
● If you have a Magnavox television, point the remote control at
the TV, then press the TV button, when using the remote con-
trol to operate the TV.
Erasure Prevention
Video cassette tapes have record tabs to ensure that recordings
1
2
are not erased accidentally.
1
To prevent erasure, break off the tab with a screwdriver.
2
To record again, cover the hole with cellophane tape.
VCR m aintenance
● Use only tapes with the
mark.
● Remove any light adhesive stick-on notes from the video cas-
sette tape before putting the tape in the VCR. Removable
labels can jam the VCR.
● Periodic maintenance is required to maintain your VCR’s excel-
lent performance. This VCR has an Automatic Head Cleaner.
However, the video heads will require replacement eventually.
Only an authorized service center should perform this service.
Helpful Hints
• Do not mix alkaline and man-
ganese batteries.
• Do not mix old and new batteries.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 6
6 Hookups Without a Cable Box / Direct Broadcast System
The basic VCR/TV connection – antenna/cable to VCR to TV – is shown below. If you have a
Cable Box or a Direct Broadcast System , please see pages eight-nine. If you have a Stereo
TV, please see page 10. After you hook up the VCR, go to page 11 to turn on the VCR.
1
Disconnect the antenna or cable from your TV.
Antenna
Indoor/O utdoor
(300 ohm)
75
ANT /
CABLE
⍀
75⍀
ANT
CABLE
/
OR
ANTENNA IN
Jack
(on back of TV)
Cable
(75 ohm)
2
Connect the antenna or cable to the ANT(enna) IN Jack of your VCR.
Back of VCR
Antenna
Indoor/O utdoor
(300 ohm)
ANT
IN
AUDIO
IN
OUT
OUT
CH3
CH4
VIDEO
ANT
IN
AUDIO
OR
OUT
IN
OUT
CH3
CH4
Cable
(75 ohm)
VIDEO
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 7
Hookups Without a Cable Box / Direct Broadcast System (cont’d) 7
3
Connect the RF coaxial cable (supplied) to the O UT Jack on the back of the
VCR and to the ANTENNA IN Jack on the TV. (You may use either a snap-on
type (supplied) or screw-on type of coaxial cable, whichever you prefer.)
ANT
IN
AUDIO
IN
OUT
OUT
CH3
CH4
Antenna
or Cable
VIDEO
ANT
IN
75
ANT /
CABLE
⍀
75⍀
ANT
/
CABLE
AUDIO
OUT
IN
OUT
ANTENNA IN Jack
(on back of TV)
exam ple only
CH3
CH4
VIDEO
RF coaxial cable
4
Plug in the TV and the VCR.
5
Set the CH3/CH4 switch on the back of the VCR to CH3 or CH4, whichever
channel is not used or least used in your area. Set the TV to the sam e channel. For
example, when playing a tape, if the CH3/CH4 switch is set to CH3, the TV should be on
channel 03.
ANT
IN
AUDIO
CH 4
or
CH 3
IN
OUT
OUT
CH3
CH4
VIDEO
ANT
IN
CH3 / CH4
Switch
AUDIO
OUT
IN
OUT
CH3
CH4
CH3
CH4
VIDEO
6
You are ready to turn on the VCR. Please go to page 11 before turning on the
VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 8
8 Hookups With a Cable Box / Direct Broadcast System
There are two ways to connect your Cable Box/DBS to the VCR. With this connection:
● You may view any channel.
● You must select channels at the Cable Box/DBS. Channels cannot be changed at the VCR.
● You may not view a channel other than the one you are recording.
● You may not program channels at the VCR.
● You can only program a timer recording for one channel at a time. Set the TV and the VCR to the
Cable Box/DBS output channel (channel 03 or 04), and set your Cable Box/DBS to the channel you
want to record. When you enter the channel you want to record in a timer recording, select channel 03
or 04 (the Cable Box/DBS output channel). (This is step 5 on page 29.) Leave the Cable Box/DBS on for
a timer recording.
VCR
Cable Box/DBS
1
2
75
ANT /
CABLE
⍀
IN
OUT
ANT
IN
AUD
RF coaxial
cable
IN
OUT
OUT
Cable
signal
CH3
CH
VIDEO
TV’s
ANTENNA IN
Jack
RF coaxial
cable
3
Connections
1
Connect a Cable signal to the IN Jack on the Cable Box/DBS.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on the
Cable Box/DBS to the ANT(enna) IN Jack on the VCR.
3
Use a second RF coaxial cable to connect the OUT Jack on the VCR to
the TV’s ANTENNA IN Jack.
Recording/Viewing Any Channel
1
With the VCR on and in VCR position (the VCR light will appear on
the display panel), use the CHANNEL o/p buttons to set the
VCR to the Cable Box/DBS output channel (channel 03 or 04).
2
Set the TV to the sam e channel to which you set the VCR.
3
Select the channel you want to view/record at the Cable
Box/DBS.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 9
Hookups With a Cable Box / Direct Broadcast System (cont’d) 9
With this connection:
● You may watch one channel while recording another.
● You may not record scrambled channels.
VCR
1
Cable Box/DBS
2
ANT
IN
75
ANT /
CABLE
⍀
AUDIO
IN
IN
OUT
OUT
OUT
CH3
CH4
VIDEO
RF coaxial
cable
Cable
signal
TV’s ANTENNA
IN Jack
RF coaxial
cable
3
Connections
1
Connect a Cable signal to the VCR’s ANT(enna) IN Jack.
2
Use an RF coaxial cable (supplied) to connect the OUT Jack on
the VCR to the IN Jack on the Cable Box/DBS.
3
Use a second RF coaxial cable to connect the OUT Jack on the
Cable Box/DBS to the ANTENNA IN Jack on the TV.
Recording O ne Channel/W atching Another
1
Put the Cable Box/DBS on the same channel as the VCR’s
CH3/CH4 switch. Then, with the VCR in VCR position (the VCR
light will appear on the display panel), use the CHANNEL o/p
buttons to select the channel you want to record at the
VCR. Start the recording.
2
Press the VCR/TV button once to put the VCR in TV
position. (The VCR light will disappear.)
Helpful Hint
3
Set the TV to the Cable Box/DBS output channel (03 or
04).
• When you play a tape, make sure
the Cable Box/DBS is set to the
same channel as the CH3/CH4
switch on the VCR. Set the TV to
the Cable Box/DBS output channel
(03 or 04).
4
Select the channel you want to watch at the Cable
Box/DBS.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 10
10 Hookups With a Stereo TV
antenna or
cable to
ANT(enna)
IN Jack
1
ANT
IN
AUDIO
IN
OUT
OUT
CH3
CH4
VIDEO
Audio and Video
IN Jacks on TV
VIDEO (yellow) and
AUDIO (white) OUT Jacks
Video Cable
2
Audio Cable
3
● Audio and Video cables are not supplied.
1
Connect the antenna or cable to the ANT(enna) IN Jack
on the back of the VCR.
2
Connect a video cable to the yellow VIDEO O UT Jack on
the back of the VCR. Then, connect the other end of the
video cable to the VIDEO IN Jack on your TV.
3
Connect an audio cable to the white AUDIO O UT Jack
on the back of the VCR. Then, connect the other end of
the audio cable to the AUDIO IN Jack on your TV.
(If your TV has Right and Left AUDIO IN Jacks, you must use a
“Y” splitter audio cable as illustrated to deliver audio to the TV’s
right and left channels.)
4
Turn on your TV, making sure it is in Line Input mode. Please
refer to your TV owner’s manual for details.
Helpful Hint
• This hookup will not give you stereo
sound. To get stereo sound, use the
connections on pages six - seven
and select the channel to be viewed
at the TV (with the VCR turned off).
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 11
Turning on Your VCR 11
Before turning on your VCR, make sure batteries are in the
remote control and the VCR and TV are connected correctly.
● Follow the steps on this page only when you plug the VCR
power cord into the wall outlet for the first time.
● You can not set up channels if you are using a Cable Box or a
Direct Broadcast System.
Turn on the TV.
2
1
2
5
8
0
3
6
1
4
7
1
5
9
Press the VCR button, then the PO W ER button. The VCR
light and the PWR. (power) light will appear on the display panel.
+100
2
PLAY
3
4
Turn on the TV. Set it to the sam e channel as the
CH3/CH4 switch on the back of the VCR. The display shown
below will appear. (If the display does not appear, check your
hookups, then follow the steps on page 12 to set up channels and
page 17 to select a language.)
REW
F.FWD
STOP
SELECT op
→ ENGLISH
ON
ESPAÑOL
MAKE SELECTION OR
PUSH MENU TO CONTINUE
3
W ithin 60 seconds, press the PLAY/o button or the
STO P/p button to select English or Spanish on-screen
displays.
Helpful Hints
4
• To skip this feature and play a tape
immediately, insert a tape with its
record tab removed. Or, to skip step
3, press the MENU button. All on-
screen displays will be in English. To
skip step 5, press the STOP button.
Channels will not be programmed,
and CHANNELS NOT SET will
appear on-screen.
Press the MENU button. The display shown below will appear.
CONNECT ANTENNA OR CABLE
TO VCR
THEN
PUSH CH UP KEY
.
.
.
OR
.
.
.
FOR PLAY ONLY – PUSH STOP
• If you try to set up channels when
there is no antenna or cable con-
nected to the VCR, programming
will appear to take place, but even-
tually a NO TV SIGNALS message
will appear. Connect an antenna or
cable to the VCR’s ANT(enna) IN
Jack and try again. You may need
to follow the steps on page 12.
5
W ithin 60 seconds, press the CHANNEL o button to
begin autom atic channel setup. AUTO SET PROCEEDING
PLEASE WAIT will appear on-screen. The VCR will memorize all
available channels. When all channels are programmed, CHAN-
NELS ARE SET will appear on-screen briefly, then TV program-
ming will appear.
Now, when you press the CHANNEL o/p buttons, you’ll only
scan through channels that you receive.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 12
12 Automatic Channel Setup
Although your VCR may automatically memorize the channels you
receive when you turn it on for the first time, this function lets
you set up the channels again.
3-5
1
2
1
Press the VCR button.
2
5
8
0
3
6
1
4
7
2
Press the MENU button.
9
+100
SELECT op CHOOSE
B
→ PROGRAM
VCR SET UP
TUNER SET UP
SET CLOCK
PLAY
REW
F.FWD
TO END PUSH EXIT
STOP
3
Press the PLAY/o button or the STO P/p button to select
TUNER SET UP, then press the F.FW D/B button.
SELECT op CHOOSE
B
→ TV
CABLE TV
ON
AUTO PROGRAMMING
ADD/DELETE CH
CH MEMORY REVIEW
TO END PUSH EXIT
4
Press the PLAY/o button or the STO P/p button to select
TV (if you have an antenna) or CABLE TV (if you have a
cable connection). Then, press the F.FW D/B button.
ON will appear beside your choice.
5
Press the PLAY/o button or the STO P/p button to select
AUTO PRO GRAMMING, then press the F.FW D/B but-
ton. The VCR will place all the channels you receive into its
memory.
6
Helpful Hints
W ait for a few m inutes while the VCR sets up the chan-
nels. When this is complete, CHANNELS ARE SET will appear
on-screen. Then the programming of the lowest channel number
placed in the VCR’s memory will appear on-screen. Now when
you press the CHANNEL o/p buttons, you will scan only
through channels you receive.
• You can not enter the TUNER SET
UP menu when you are in Line
Input mode (channel 00). When
you select channel 00, A/V IN will
appear on-screen briefly.
• You can not program channels if
you are using a Cable Box or DBS.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 13
Automatic Channel Setup (cont’d) 13
Adding/Deleting Channels
1 3-4
1
Press the VCR button.
2
Press the MENU button.
2
5
8
0
3
6
1
4
7
3
Press the PLAY/o button or the STO P/p button to select
TUNER SET UP, then press the F.FW D/B button.
9
+100
4
PLAY
Press the PLAY/o button or the STO P/p button to select
ADD/DELETE CH, then press the F.FW D/B button.
5
2
REW
F.FWD
STOP
SELECT op ADD/DELETE
B
6
7
124
125
1
DELETED
DELETED
DELETED
ADDED
→
2
3
ADDED
TO END PUSH EXIT
5
Press the PLAY/o button or the STO P/p button until the
channel num ber you want to add or delete appears beside
the arrow.
SELECT op ADD/DELETE
B
16
17
18
19
20
DELETED
ADDED
ADDED
ADDED
ADDED
→
TO END PUSH EXIT
6
Press the F.FW D/B button to select ADDED or DELET-
ED.
7
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 14
14 Automatic Channel Setup (cont’d)
Reviewing Mem orized Channels
1
3-4
1
Press the VCR button.
2
Press the MENU button.
2
5
8
0
3
6
1
4
7
SELECT op CHOOSE
B
→ PROGRAM
VCR SET UP
TUNER SET UP
SET CLOCK
9
+100
TO END PUSH EXIT
PLAY
3
REW
F.FWD
Press the PLAY/o button or the STO P/p button to select
TUNER SET UP, then press the F.FW D/B button.
STOP
SELECT op CHOOSE
B
→ TV
CABLE TV
ON
AUTO PROGRAMMING
ADD/DELETE CH
CH MEMORY REVIEW
2
TO END PUSH EXIT
5
4
Press the PLAY/o button or the STO P/p button to select
CH MEMO RY REVIEW , then press the F.FW D/B button.
A list of programmed channels will appear on-screen.
● If all the programmed channels don’t fit on the screen, press
the F.FWD/B button to see the remaining channels. Then
press the REW(ind)/s button to return to the first screen of
channels.
● If you do not press any buttons within 10 seconds, you will
either go to the next screen of channels or you will return to
the previous menu.
5
Press the STATUS/EXIT button once or twice to exit.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 15
Setting the Clock 15
Follow the steps below to set your VCR’s clock. Make sure:
● The VCR is on and the VCR light appears on the display panel.
(If it does not, press the VCR/TV button once.)
5-6
● You make each entry within 60 seconds of the previous entry.
3-4
1
1
Press the VCR button.
2
5
8
0
3
6
1
4
7
2
Press the MENU button.
9
+100
3
Press the PLAY/o button or the STO P/p button to select
SET CLO CK, then press the F.FW D/B button.
PLAY
REW
F.FWD
STOP
4
Press the PLAY/o button or the STO P/p button to select
SET CLO CK, then press the F.FW D/B button.
2
5
7
Press two Num ber buttons for the hour(s) and two
Num ber buttons for the m inute(s). Then press 1 for AM
or 2 for PM. For example, for 2:15 PM, press 02, 15, 2.
Helpful Hints
6
• Enter a 0 before a single digit num-
ber.
• Entries that do not match the VCR’s
calendar will cause a question mark
to appear on-screen.
Press two Num ber buttons for the m onth, two Num ber
buttons for the day, and two Num ber buttons for the
year. For example, for July 1, 1998, press 07, 01, 98. The day of
the week will appear automatically.
• To make corrections, press the
CLEAR button until the space for the
number you want to correct is flash-
ing. Then enter the correct number.
• The current time will appear on the
VCR display panel when the clock is
set. The current time will also
appear on-screen if you press the
STATUS/EXIT button. (See page 20
for details.)
7
Press the STATUS/EXIT button.
• Power failures that last for more
than one minute can cause you to
lose your clock setting.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 16
16 Daylight-Saving Time
You may program the VCR so its clock will automatically move
forward one hour in April and turn back one hour in October.
Daylight-Saving Time is set to ON when you receive your VCR.
Turn Daylight-Saving Time ON or OFF by following the steps
below. Before you begin:
1
3-4
● Make sure the clock is set.
2
5
8
0
3
6
1
4
7
1
Press the VCR button.
9
2
+100
Press the MENU button.
SELECT op CHOOSE
B
PLAY
→ PROGRAM
VCR SET UP
TUNER SET UP
SET CLOCK
REW
F.FWD
STOP
TO END PUSH EXIT
2
5
3
Press the PLAY/o button or the STO P/p button to select
SET CLO CK, then press the F.FW D/B button.
SET CLOCK
SET CLOCK
→ DAYLIGHT SVG TIME [ON]
SELECT op CHOOSE
B
TO END PUSH EXIT
4
Press the PLAY/o button or the STO P/p button to select
DAYLIGHT SVG TIME. Then, press the F.FW D/B button
so that O FF (or O N) appears beside DAYLIGHT SVG
TIME.
5
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 17
Language Selection 17
Follow the steps below to change the language of the on-screen
displays.
1
3-4
1
Press the VCR button.
2
2
5
8
0
3
6
1
4
7
Press the MENU button.
SELECT op CHOOSE
B
9
→ PROGRAM
VCR SET UP
TUNER SET UP
SET CLOCK
+100
TO END PUSH EXIT
PLAY
5
REW
F.FWD
3
STOP
Press the PLAY/o button or the STO P/p button to select
VCR SET UP, then press the F.FW D/B button.
SELECT op CHOOSE
B
2
6
→ REPEAT PLAY
ON SCREEN MODE
LANGUAGE
VCR PLUS+ REF. MAP
TO END PUSH EXIT
OFF
4
Press the PLAY/o button or the STO P/p button to select
LANGUAGE, then press the F.FW D/B button.
SELECT op
→ ENGLISH
ON
ESPAÑOL
MAKE SELECTION OR
TO END PUSH EXIT
Helpful Hint
• If you accidentally select Spanish
on-screen displays and need English
on-screen displays:
1. Press the VCR button.
2. Press the MENU button.
5
Press the PLAY/o button or the STO P/p button to select
English or Spanish on-screen displays.
3. Press the PLAY/o button or the
STOP/p button to select PREPARE
EL VCR, then press the F.FWD/B
button.
6
Press the STATUS/EXIT button.
4. Press the PLAY/o button or the
STOP/p button to select LENGUA-
JE, then press the F.FWD/B button.
5. Press the PLAY/o button or the
STOP/p button to select ENGLISH.
6. Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 18
18 Remote Control Buttons
PO W ER Button
Press to turn on or off the VCR or a Magnavox TV. (You must first
press the VCR or TV button.)
Num ber Buttons
Use to select channels at the VCR or a Magnavox TV; use to set up
VCR features (such as the clock).
Channels 1 - 9 ●
To select, press 0, then the channel number you want. For
example, to select channel 7, press 0, 7.
2
5
8
0
3
6
Channels 100 and above ●
1
4
7
To select, press the +100 button, then press the last two digits of the
channel you want. For example, to select channel 117, press the +100
button, 1, 7. (You can not select channels above 99 at the Magnavox
TV.)
9
+100
VCR PLUS+ Button
Press to set a timer recording with the VCR Plus+
programming system. Details are on pages 32 - 35.
PLAY
REW
F.FWD
SPEED Button
Press to select the recording speed (SP, LP, or SLP). Details are on
pages 30 and 44.
STOP
REW (ind)/{ Button
When tape playback is stopped, press to rewind the tape at high
speed. During playback, press to rewind the tape while the picture
stays on-screen. Details are on page 39. Or, if you have a Magnavox
TV, use the REW(ind) button to adjust the picture controls in the TV
menu.
MEMO RY Button
Press to memorize a tape position at which the real-time counter was
set to 0:00:00. Details are on page 38.
REC(ord)/O TR Button
Press once to start a recording. Details are on page 25. Or, press
repeatedly to start a One-Touch Recording. Details are on page 27.
MENU Button
Press to access the VCR menu. Or, if you have a Magnavox TV, press
the TV button, then press the MENU button to display the TV menu.
STATUS/EXIT Button
Press to access or remove the on-screen status display. Details are on
page 20. Press to exit on-screen menus. Or, if you have a Magnavox
TV, press the TV button, then press the STATUS/ EXIT button, to
see a TV status display or to remove the TV menu.
PLAY/o Button
Press to play a tape; press to release Search or Still mode and return
to normal playback. Details are on page 39. Press to select an item in
the on-screen menu. Or, if you have a Magnavox TV, press when in
TV mode to move up one row or selection in the TV menu.
Helpful Hint
• Press the VCR button before press-
ing VCR feature buttons; press the
TV button before pressing TV fea-
ture buttons if you have a
Magnavox TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 19
Remote Control Buttons (cont’d) 19
TV Button
Press to operate a Magnavox TV.
VCR Button
Press to operate the VCR.
VCR/TV Button
Use to select VCR or TV position.
VCR Position ●
Use to watch a tape, to watch a program while recording it, or to
watch a TV program (changing channels at the VCR). If the VCR
light appears on the display panel of the VCR, it is in VCR position.
TV Position ●
Use to watch a TV program (changing channels at the TV) or to
watch one program while recording another. Details are on page 26.
If the VCR light doesn’t appear on the display panel, the VCR is in
TV position.
2
5
8
0
3
6
1
4
7
9
+100
PLAY
CHANNEL o/p Buttons
REW
F.FWD
Press to change channels at the VCR or at a Magnavox TV.
STOP
VO LUME o/p Buttons
Press to adjust the TV’s volume.
MUTE Button
Press to eliminate the TV’s sound. Press again to restore the volume.
STO P/p Button
Press to stop the tape. Press to select an item in the VCR menu. Or,
if you have a Magnavox TV, press when in TV mode to move down
one row or selection in the TV menu.
CLEAR Button
Press to erase incorrect information when programming VCR fea-
tures. Press to reset the real-time counter. Details are on page 38.
EJECT Button
Press to eject the tape.
PAUSE/STILL Button
During recording, press to pause the recording. Press a second time
to resume normal recording. Details are on page 25. You can not
pause a One-Touch Recording. During playback, press to freeze the
picture. Details are on page 39.
F.FW D(Fast Forward)/B Button
When playback is stopped, press to fast forward the tape at high
speed. During playback, press to fast forward the tape while the pic-
ture stays on-screen. Details are on page 39. Or, if you have a
Magnavox TV, use to adjust the picture controls in the TV menu.
Helpful Hint
• Buttons with a shaded description
may also operate features of a
Magnavox TV.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 20
20 On-Screen Status Displays
A status display will appear when you press the STATUS/EXIT
button or certain function buttons. The contents of the status dis-
play will vary. To choose the status display mode, follow the steps
below.
If you select STATUS O N, then select CO UNTER O NLY
O N:
Status Display
(exam ple only)
● Whenever you press the STOP/p button or the PLAY/o but-
ton, the status display will appear for five seconds. After five
seconds, only the counter will remain on-screen. You must
press the STATUS/EXIT button to remove it.
If you select STATUS O N, then select CO UNTER O NLY
O FF:
Button
Pressed
Time
STOP
12:00AM
CH10
● Whenever you press the STOP/p button or the PLAY/o but-
ton, the status display will appear for five seconds.
If you select STATUS O FF:
SLP
M 1:23:45
● The status display will not appear when you press function but-
tons. You must press the STATUS/EXIT button to see the sta-
tus display.
Channel
Counter
and
Tape
Speed
Counter
Memory
1
Press the VCR button, then press the MENU button.
2
Press the PLAY/o button or the STO P/p button to select
VCR SET UP, then press the F.FW D/B button.
3
Press the PLAY/o button or the STO P/p button to select
O N SCREEN MO DE, then press the F.FW D/B button.
4
Press the PLAY/o button or the STO P/p button to select
STATUS, then press the F.FW D/B button so that O FF
(or O N) appears beside STATUS.
SELECT op CHOOSE
B
→ STATUS
COUNTER ONLY
[ON]
[OFF]
TO END PUSH EXIT
Helpful Hints
5
If you set STATUS to O FF, go to step 6. If you set STA-
TUS to O N, press the PLAY/o button or the STO P/p
button to select CO UNTER O NLY, then press the
F.FW D/B button so that O FF (or O N) appears beside it.
• If the channel you select has no
broadcast, the screen will become
solid blue.
• You may not access a status display
when viewing a still picture or when
the F.FWD/B or REW(ind)/s but-
ton is pressed during playback.
6
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 21
VCR Display Panel 21
Cassette Com partm ent
Insert a tape here.
PLAY
REW
F.FWD
STOP
EJECT
PWR.
VCR
PM
REC(ord) Light
This light appears during a record-
ing. It flashes when a recording is
paused.
Tim er Light
This light glows when the VCR
is turned off to set a timer
recording or during a One-
Touch Recording. It flashes if
the power is off for a timer
recording, but there is no tape
in the VCR. It flashes when all
timer recordings are finished.
REC
PM
PWR.
VCR
PW R.(power) Light
This light appears when the
power is on.
Cassette-Inside Light
This light appears when there is
a tape in the VCR.
Clock Display
The current time
appears here when the
clock is set. If the clock
is not set, -:-- will appear
here. PM will appear on
the display, but AM will
not.
VCR Light
This light appears when the
VCR is in VCR position. This
light does not appear when
the VCR is in TV position.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 22
22 Front Panel
F.FW D (Fast Forward) Button
When playback is stopped, press to fast forward the tape
at high speed. During tape playback, press to fast forward
while the picture stays on-screen. Details are on page 39.
Rem ote Sensor
Receives a signal from your
remote control so you can oper-
ate your VCR from a distance.
STO P/EJECT Button
Press once to stop the tape. When play-
back is stopped, press to eject the tape.
PO W ER Button
Press to turn the VCR power on and off.
PLAY Button
Press to play a tape. Press to
release Search or Still mode
and return to playback.
Details are on page 39.
REW (ind) Button
When playback is stopped, press
to rewind the tape at high speed.
During playback, press to rewind
the tape while the picture stays
on-screen. Details are on page 39.
PLAY
REW
F.FWD
STOP
EJECT
PWR.
VCR
PM
CHANNEL (p/o) Buttons
Press to change channels at the
VCR. Or, press to adjust the
tracking of a tape during play-
back.
VCR/TV Button
Press to select VCR or TV position.
● VCR Position
REC(ord)/O TR Button
Press once to start a record-
ing. Press repeatedly to start
a One-Touch Recording.
Details are on page 27.
Use to watch a tape, to watch a program
while recording it, or to watch a TV pro-
gram (changing channels at the VCR).
When the VCR light appears on the dis-
play panel, the VCR is in VCR position.
● TV Position
Use to watch TV (changing channels at
the TV) or to watch one program while
recording another. When the VCR light
does not appear on the display panel, the
VCR is in TV position.
PAUSE Button
While recording, press to pause the recording. Press
again to resume recording. Details are on page 25. You
can not pause a One-Touch Recording. During tape
playback, press to freeze the picture. Details are on
page 39.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 23
Rear Panel 23
ANT(enna) IN Jack
Connect your antenna or cable
here. Details are on pages six - 10.
AUDIO IN Jack
Connect a cable coming from the
AUDIO OUT Jack of a camcorder,
another VCR, or an audio source
here. Details are on page 36.
AUDIO O UT Jack
Connect a cable going to the
AUDIO IN Jack of a camcorder,
another VCR, or an audio source
here. Details are on page 36.
ANT
IN
AUDIO
IN
OUT
OUT
CH3
CH4
VIDEO
VIDEO O UT Jack
Connect a cable going to the VIDEO
IN Jack of a camcorder, another
VCR, or an audio-visual source
(laser disc player, video disc player,
etc.) here. Details are on page 36.
CH3/CH4 Switch
Set to channel 3 or 4
to use your TV with
your VCR. Details are
on pages six - nine.
VIDEO IN Jack
Connect a cable coming from the
VIDEO OUT Jack of a cam-
corder, another VCR, or an
audio-visual source (laser disc
player, video disc player, etc.)
here. Details are on page 36.
AC Power Cord
Connect to a stan-
dard AC outlet to
supply power to the
VCR.
O UT Jack
Use the supplied RF coaxi-
al cable to connect this
jack to the ANTENNA IN
Jack on your TV, Cable
Box, or Direct Broadcast
System. Details are on
pages six - nine.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 24
24 Playing
Read and follow the steps below to play a tape.
Turn on the TV.
1
2
Insert a tape in the VCR.
1
Turn on the TV and set it to channel 03 or 04, whichever
the CH3/CH4 switch on the back of the VCR is set to.
2
Insert a tape in the VCR. The PWR., VCR, and Cassette-Inside
lights will appear on the display panel. If the tape’s record tab has
been removed, playback will start automatically.
2
5
8
0
3
6
1
4
7
9
3
+100
If playback does not start autom atically, press the
PLAY/o button.
3
5
4
PLAY
4
REW
F.FWD
STOP
Press the STO P/p button on the rem ote control or the
STO P/EJECT button on the VCR once to stop playback.
6
5
Press the REW (ind)/{ button to rewind the tape.
6
W hen the tape stops, press the EJECT button on the
rem ote control or the STO P/EJECT button on the VCR
to rem ove the tape.
Helpful Hints
• If the tape you want to play is
already in the VCR, make sure the
VCR power is on and the VCR is in
VCR position. (The VCR light will
appear on the display panel. If it
does not, press the VCR/TV button.)
Press the VCR button, then press
the PLAY/o button.
• Other playback options and fea-
tures are on pages 37 - 40.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 25
Recording 25
Read and follow the steps below to record a television program.
Turn on the TV.
1
2
Insert a tape in the VCR.
1
Turn on the TV and set it to channel 03 or 04, whichever
the CH3/CH4 switch on the back of the VCR is set to.
3
2
Insert a tape with its record tab intact in the VCR.
2
5
8
0
3
6
1
4
7
4
6
3
9
Press the VCR button.
+100
4
5
7
If the VCR light appears on the display panel, go to step 5. If the
VCR light does not appear, press the VCR/TV button
once.
PLAY
REW
F.FWD
STOP
9
8
5
Press the SPEED button until the desired tape speed appears
briefly on-screen. (Details about tape speed are on page 30.)
6
Use the CHANNEL o/p buttons or the Num ber buttons
to select the channel to be recorded.
7
Press the REC(ord)/O TR button once to start recording.
The REC light will appear.
Helpful Hints
8
• If you press the REC(ord)/OTR but-
ton when there is not a tape in the
VCR, NO CASSETTE will flash on-
screen.
To pause the recording, press the PAUSE/STILL button
once. The REC light will flash. To resum e recording, press
the REC(ord)/O TR button or press the PAUSE/STILL
button again. The REC light will come on again.
• If you press the REC(ord)/OTR but-
ton while a tape without a record
tab is in the VCR, the VCR will eject
the tape and PROTECTED CAS-
SETTE CANNOT RECORD will flash
on-screen.
9
To stop recording, press the STO P/p button.
• Other recording options are on
pages 26 - 36.
• You can change the tape speed
during a recording, but some distor-
tion will appear on the tape.
• The VCR will record in a preset vol-
ume.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 26
26 Recording One Channel/Watching Another
1
2&6
Start a recording. (See page 25.)
2
Press the VCR button.
2
5
8
0
3
6
1
4
7
3
7
3
Press the VCR/TV button to put the VCR in TV position.
The VCR light will disappear from the VCR’s display panel.
9
+100
4
PLAY
Choose the channel you want to watch at the TV.
REW
F.FWD
STOP
5
8
To return to the channel being recorded, select channel
03 or 04 at the TV (whichever channel the CH3/CH4 switch on
the back of the VCR is set to).
1
6
Press the VCR button.
7
Press the VCR/TV button to put the VCR in VCR posi-
tion. The VCR light will appear on the display panel. The channel
being recorded will appear on-screen.
Select the channel you want to
watch at the TV.
4
5
Select channel 03 or 04 at the
TV.
8
Press the STO P/p button to stop the recording.
Helpful Hints
• If you use a Cable Box or Direct
Broadcast System hookup, you may
not be able to watch one channel
while recording another. See pages
eight-nine for details.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 27
One-Touch Recording 27
The One-Touch Recording (OTR) feature allows you to set an
immediate timed recording 30 minutes to eight hours long. Before
you begin:
1
● Set up the channels at the VCR.
● Select a recording speed (SP, LP, SLP) with the SPEED button.
● Put a tape in the VCR. Make sure the tape’s record tab is intact
and the tape is long enough to record the program(s).
● Place the VCR in VCR position. (The VCR light will appear on
the display panel. If it does not, press the VCR/TV button once.)
2
5
8
0
3
6
1
4
7
2
9
+100
1
Press the VCR button.
4
3
PLAY
2
REW
F.FWD
Press the CHANNEL o/p buttons or the Num ber but-
tons to select the channel you want to record.
STOP
3
Press the REC(ord)/O TR button repeatedly until the
desired recording length (30 m inutes to eight hours)
appears on-screen. Recording will begin immediately. The REC
light and the Timer light will appear on the display panel.
OTR (0:30)
CH12
4
To stop an O TR before recording is finished, press the
STO P/p button or the PO W ER button.
To cancel the OTR but continue recording, press the
REC(ord)/OTR button repeatedly until REC appears in the upper
left corner of the TV screen. The REC light will remain on the
display panel of the VCR, but the Timer light will disappear.
Helpful Hints
• To check the time remaining for an
OTR after the OTR has been set,
press the STATUS/EXIT button.
• To change the recording length
while an OTR is in progress, press
the REC(ord)/OTR button until the
desired length appears on-screen.
• If you begin an OTR when another
recording is paused, the OTR will
begin.
• You can not pause an OTR.
• If the preset time for a timer
recording comes up during an OTR,
the OTR has priority. The timer
recording will not take place.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 28
28 Timer Recording
Follow the steps below to program your VCR to record TV pro-
grams while you’re away from home. The VCR will turn itself on,
record, and turn itself off automatically. Before you begin:
● Set up the channels at the VCR.
2-3
● Set the clock.
● Put a tape in the VCR. Make sure the tape’s record tab is intact
and the tape is long enough to record the program(s).
● Put the VCR in VCR position. The VCR light will appear on the
display panel. If it does not, press the VCR/TV button once.
2
5
8
0
3
6
1
4
7
Do each step within 60 seconds of the previous step.
9
+100
1
Press the VCR button, then press the MENU button.
PLAY
REW
F.FWD
SELECT op CHOOSE
B
STOP
→ PROGRAM
VCR SET UP
TUNER SET UP
SET CLOCK
TO END PUSH EXIT
1
2
Press the PLAY/o button or the STO P/p button to select
PRO GRAM, then press the F.FW D/B button.
SELECT op CHOOSE
B
→ ONCE
DAILY
WEEKLY
PROGRAM REVIEW
TO END PUSH EXIT
3
Press the PLAY/o button or the STO P/p button to select
a O NCE, DAILY, O R W EEKLY recording. Then, press
the F.FW D/B button.
● O NCE: The VCR will record a TV program on any day you
choose, up to 12 months away.
● DAILY: The VCR will record every day from Monday to Friday
– starting at the same time and recording for the same length of
time.
● W EEKLY: The VCR will record on the same day, at the same
time, and for the same length of time every week.
Helpful Hint
DAILY PROGRAM (MON-FRI)
Daily
PROGRAM -1 2 3 4 5 6 7 8-
• If you need to make a correction
while programming a timer record-
ing, press the CLEAR button until
the cursor is flashing on the item
you want to change. Then enter the
correct information.
Recording
(exam ple)
SELECT PROGRAM NUMBER
TO END PUSH EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 29
Timer Recording (cont’d) 29
4
Use the Num ber buttons (1 - 8) to select a slot in which
to store the tim er recording. There are eight slots. Open
slots will flash on-screen.
4-7
NOTE: If you enter a number for a slot that has already been used to
store a timer recording, PREVIOUSLY SET PROGRAM will appear on-
screen briefly. Information about the program in that slot will appear
on-screen. If this happens, press the STATUS/EXIT button, then select
another number.
2
5
8
0
3
6
1
4
7
9
5
+100
Use the Num ber buttons to enter the channel you want
to record.
● If you have a basic antenna or cable hookup (as shown on
pages six-seven) enter the channel number of the TV program
you want to record. (Enter a 0 before all single-digit channels.)
● If you are recording from line input, press 0, 0. A/V IN will
appear on-screen.
PLAY
REW
F.FWD
STOP
● If you are using a Cable Box/DBS, enter the Cable Box/DBS
output channel (03 or 04). See page eight for details.
ONE TIME PROGRAM
PROGRAM
CHANNEL
1
– –
TO CORRECT PUSH CLEAR
TO END PUSH EXIT
6
Press two Num ber buttons for the hour you want the
recording to begin. Press two Num ber buttons for the
m inute you want the recording to begin. Press 1 for AM
or 2 for PM. For example, for 9:30 PM, press 09, 30, 2.
ONE TIME PROGRAM
PROGRAM
CHANNEL
TIME ON
1
10
– – : – –
TO CORRECT PUSH CLEAR
TO END PUSH EXIT
7
Follow the instructions in step 6 to enter the recording’s
stop tim e. (AM or PM will be set automatically.)
ONE TIME PROGRAM
PROGRAM
CHANNEL
TIME ON
1
10
09:30 PM
– – : – –
TIME OFF
Helpful Hint
TO CORRECT PUSH CLEAR
TO END PUSH EXIT
• Entries that do not match the VCR’s
clock or calendar will cause a ques-
tion mark to appear on-screen.
Instructions continue on page 30.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 30
30 Timer Recording (cont’d)
8
Press the Num ber 1 button to record in SP speed, the
Num ber 2 button to record in LP speed, or the Num ber 3
button to record in SLP speed. (See the chart below.) You
cannot use the SPEED button at this time.
11 8
ONE TIME PROGRAM
PROGRAM
CHANNEL
TIME ON
TIME OFF
REC SPEED
1
10
09:30 PM
11:00 PM
SLP
2
5
8
0
3
6
1
4
7
SP=1 LP=2 SLP=3
TO CORRECT PUSH CLEAR
TO END PUSH EXIT
9
9
+100
9
Press two Num ber buttons for the m onth and two
Num ber buttons for the day you want to record the pro-
gram . For example, for July 10, 1998, press 07, 10. The day of
the week and the year will appear automatically (you cannot pro-
gram the VCR to record more than one year in advance).
PLAY
REW
F.FWD
STOP
ONE TIME PROGRAM
PROGRAM
CHANNEL
TIME ON
TIME OFF
REC SPEED
START DATE
1
10
09:30 PM
11:00 PM
SLP
07/10/98
FRI.
10
TO CORRECT PUSH CLEAR
TO END PUSH EXIT
10
Press the STATUS/EXIT button. PROGRAM WAS COM-
PLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING
will appear on-screen briefly. (If PROGRAM NOT COMPLETED
appears, try again from step 1.)
The VCR m ust
be off for a
tim er recording.
Put a tape in the
VCR.
11
Turn off the VCR power. The Timer light will appear on the
display panel.
If the timer recording will take place several hours or days from
now, you may use the VCR until time for the recording. Turn off
the VCR a few minutes before the recording starts. If you forget
to turn off the VCR, PLEASE TURN OFF VCR FOR TIMER
RECORDING flashes on your TV screen two minutes before a
timer recording starts. Press the CLEAR button to remove the
message.
Tape Speed
Type
SP
(Standard Play)
LP
(Long Play)
SLP
Maximum Record/Playback Time
Tape Speeds
T160
2 hrs.
40 mins.
5 hrs.
T120
T60
This chart shows the recording/playback time
for three types of video cassettes (T160, T120,
and T60). There are three playback speeds: SP,
LP, and SLP. When recording, you can change
the tape speed using the SPEED button.
2 hrs.
1 hr.
4 hrs.
6 hrs.
2 hrs.
3 hrs.
20 mins.
8 hrs.
(Super Long Play)
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 31
Timer Recording (cont’d) 31
Checking or Cancelling Tim er Recordings
2-3
1
With the VCR on and in VCR position (the VCR light will appear
on the display panel), press the VCR button, then press the
MENU button.
2
5
8
0
3
6
1
4
7
2
9
Press the PLAY/o button or the STO P/p button to select
PRO GRAM, then press the F.FW D/B button.
+100
3
PLAY
Press the PLAY/o button or the STO P/p button to select
PRO GRAM REVIEW , then press the F.FW D/B button.
The timer recording information for the program in the lowest
numbered slot will appear on-screen. If no timer recordings are
set, nothing will happen when you press the F.FWD/B button.
REW
F.FWD
4
5
STOP
1
4
Press the F.FW D/B button repeatedly to review all pro-
gram m ed tim er recordings. If you don’t press the F.FWD/B
button within 10 seconds, the VCR will automatically display infor-
mation about the next programmed timer recording. This will
continue until all timer recordings have been displayed. Then the
menu will disappear.
5
Helpful Hints
To cancel the tim er recording displayed, press the
CLEAR button. Either the display will disappear or information
about other timer recordings will appear. If you do not press any
other buttons, the display will disappear after all timer recordings
have been displayed.
• CLASH may flash on-screen when
you finish setting a timer recording.
This means that the timer recording
you just programmed and another
timer recording overlap. The current
timer recording will not take place.
You may choose to cancel the over-
lapping timer recording.
• If the preset time for a timer
recording comes up during a One-
Touch Recording, the OTR has pri-
ority.
6
Repeat steps 1 - 4 to m ake sure you have cleared the cor-
rect tim er recording.
• To stop a started timer recording,
press the STOP/EJECT button on
the VCR.
• If the power fails for more than one
minute, programmed timer record-
ings will be lost. Reset the clock
before resetting the timer record-
ings.
See page 42 for m ore hints.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 32
32 Setting Up the VCR Plus+ Programming System
1
First, fill in the boxes on this page. It will only take a few minutes, and you must do it if you want the VCR
Plus+ programming system to work properly.
Since the channel numbers of the stations you receive may not be the same as the station numbers, and
since channel numbers differ from area to area, you must program the VCR with your local channel infor-
mation. To fill in the boxes, you will need 1) a cable channel list, if applicable (you can request one from
your cable company), and 2) a chart that lists VCR Plus+ channel numbers, which you can find in your TV
guide or the TV listings of your local newspaper.
Channels
Channels
Station
Call Letters
Station
Call Letters
VCR PLUS+ CH.
VCR PLUS+ CH.
CABLE/TV CH.
CABLE/TV CH.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 33
Setting Up the VCR Plus+ Programming System (cont’d) 33
Examine the lists on
page 32.
2
2
Now, compare the channel numbers you have written in the VCR
PLUS+ CH. and CABLE/TV CH. columns. For stations whose VCR
Plus+ and Cable/TV channels do not match, you must tell the VCR
the VCR Plus+ and Cable/TV channel numbers by following steps
3 - 7. Make each entry within 60 seconds of the previous entry.
4-5
2
5
8
0
3
6
1
4
7
3
Press the VCR button, then press the MENU button.
9
+100
4
Press the PLAY/o button or the STO P/p button to select
VCR SET UP, then press the F.FW D/B button.
PLAY
SELECT op CHOOSE
B
REW
F.FWD
6
→ REPEAT PLAY
ON SCREEN MODE
LANGUAGE
OFF
STOP
VCR PLUS+ REF. MAP
TO END PUSH EXIT
3
7
5
Press the PLAY/o button or the STO P/p button to select
VCR PLUS+ REF. MAP, then press the F.FW D/B button.
VCR PLUS+ CROSS REF. MAP
VCR PLUS+
CABLE/TV
98
99
1
2
98
99
– – – – –
1
2
>
TO SELECT CH PUSH op
THEN ENTER CH NO.
TO END PUSH EXIT
6
Look at the lists you filled in on page 32. For stations whose
VCR Plus+ and Cable/TV channels do not m atch, press
the PLAY/o button or the STO P/p button until the
arrow is beside the VCR Plus+ channel you need. Then,
press the Num ber buttons to enter the corresponding
Cable/TV channel from your list. (Enter a “0” before single-
digit channels.) Enter all the stations on your list.
Helpful Hints
• To erase a Cable/TV channel num-
ber, repeat steps 3-5 on this page.
Then, press the PLAY/o button or
the STOP/p button to select it.
Press the CLEAR button, then press
the STATUS/EXIT button.
VCR PLUS+ CROSS REF. MAP
VCR PLUS+
CABLE/TV
98
99
98
99
1
2
– – – – – 23
>
2
TO SELECT CH PUSH op
THEN ENTER CH NO.
TO END PUSH EXIT
• To select line input for the Cable/TV
channel, press 0,0. AUX will appear
on-screen.
• When you receive the VCR, all the
VCR Plus+ channel numbers and
Cable/TV channel numbers are the
same.
7
Press the STATUS/EXIT button.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 34
34 Timer Recording With the VCR Plus+ Programming System
Follow these steps to set a timer recording with the PlusCode
programming numbers in your TV guide. Before you begin:
● Set up the channels at the VCR (page 12).
● Set up the VCR Plus+ and Cable/TV channel numbers (pages 32
- 33).
● Set the clock (page 15).
1
● Put a tape in the VCR.
● Turn on the VCR power. The VCR light should appear on the
display panel. If it does not, press the VCR/TV button once.
Do each step within 60 seconds of the previous step.
2
5
8
0
3
6
1
4
7
3
9
+100
2
4
1
Press the VCR button.
PLAY
REW
F.FWD
STOP
2
Press the VCR PLUS+ button.
VCR PLUS+ PROG.
PLUS CODE : – – – – – – – –
TO END PUSH EXIT
3
Press the Num ber buttons to enter the PlusCode pro-
gram m ing num ber of the program you wish to record.
Then, press the VCR PLUS+ button.
VCR PLUS+ PROG.
PLUS CODE : 13285 – – –
Helpful Hints
TO SET PUSH VCR+
TO CORRECT PUSH CLEAR
TO END PUSH EXIT
• CODE ERROR may flash on-screen
after step 3 if you enter an incorrect
number (for example, one that is too
short). The previous screen will
appear. Enter the correct PlusCode
programming number.
• If the VCR PLUS+ CROSS REF. MAP
reappears after step 3, the VCR
PLUS+ channel number for the
recording you entered was higher
than 99. In this case, enter the cor-
rect CABLE/TV channel in the map.
Then, press the MENU button and
continue from step 4.
4
Press the PLAY/o button or the STO P/p button to select
a O NCE, DAILY, O R W EEKLY recording. Then, press the
F.FW D/B button.
● O NCE: The VCR will record a TV program on any day you
choose, up to 12 months away.
● DAILY: The VCR will record every day from Monday to Friday
– starting at the same time and recording for the same length of
time.
● W EEKLY: The VCR will record on the same day, at the same
time, and for the same length of time every week.
VCR PLUS+ PROG.
• If CLASH flashes on-screen at step
3, the timer recording you just pro-
grammed and another timer record-
ing overlap. The current timer record-
ing will not occur.
→ ONCE
DAILY
WEEKLY
SELECT op CHOOSE
B
TO END PUSH EXIT
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 35
Timer Recording With the VCR Plus+ Programming System (cont’d) 35
5
Press the Num ber 1 button to record in SP speed, the
Num ber 2 button to record in LP speed, or the Num ber 3
button to record in SLP speed. Your selection will appear
beside REC SPEED on-screen; SP=1 LP=2 SLP=3 will continue to
flash. For details about tape speed, see pages 30 and 44. You can-
not use the SPEED button at this time.
7
5
2
5
8
0
3
6
1
4
7
ONE TIME PROGRAM
PROGRAM
CHANNEL
TIME ON
TIME OFF
REC SPEED
1
09
10:30 PM
11:30 PM
SLP
9
SP=1 LP=2 SLP=3
START DATE
10/10/98
SAT.
+100
TO END PUSH EXIT
PLAY
6
REW
F.FWD
Press the STATUS/EXIT button. PROGRAM WAS COM-
PLETED / PLEASE TURN OFF VCR FOR TIMER RECORDING
should appear on-screen briefly.
STOP
7
Press the PO W ER button to turn off the VCR power. The
Timer light will appear. The Timer light will flash if there is not a
tape in the VCR.
6
If the timer recording will take place several hours or days from
now, you may use the VCR until time for the recording. Just turn
off the VCR a few minutes before the recording starts. If you for-
get to turn off the VCR, PLEASE TURN OFF VCR FOR TIMER
RECORDING flashes on your TV screen two minutes before a
timer recording starts. Remove the message by pressing the
CLEAR button.
Helpful Hints
• If the time for a timer recording
comes up during a One-Touch
Recording, the OTR has priority.
• To stop a started timer recording,
press the STOP/EJECT button on
the VCR.
• If the power fails for more than one
minute, programmed timer record-
ings may be lost. Reset the clock
before resetting the timer record-
ings.
• If you are using a Cable Box, timer
recordings are programmed differ-
ently. See page eight for details.
See page 42 for m ore hints.
The VCR m ust be off for a
tim er recording to take
place! Make sure there is a
tape in the VCR.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 36
36 Rerecording (Tape Duplication)
1. Audio cable from AUDIO O UT Jack of
VCR 1 to AUDIO IN Jack of VCR 2
VCR 1
Playing VCR
VCR 2 - Recording VCR
ANT
IN
ANT
IN
AUDIO
AUDIO
IN
IN
OUT
OUT
OUT
OUT
CH3
CH4
CH3
CH4
VIDEO
VIDEO
3. RF coaxial
cable from VCR’s
O UT Jack to TV’s
ANTENNA IN
Jack
2. Video cable from VIDEO O UT Jack
of VCR 1 to VIDEO IN Jack of VCR 2
● Audio and video cables are not supplied.
1
Make the connections shown above.
2
VCR 1 will play your tape. Put a prerecorded tape in VCR 1.
3
VCR 2 will record your tape. Insert a blank tape in VCR 2. The
VCR must be in VCR position. (The VCR light will appear on the display
panel. If it does not, press the VCR/TV button once.)
4
Turn on the TV and set it to channel 03 or 04, whichever
channel the CH3/CH4 switch on VCR 2 is set to.
5
Point the rem ote control at VCR 2. Press Num ber but-
tons 0, 0 to select Line Input. A/V IN will appear on-screen.
Helpful Hints
• Unauthorized recording of copy-
righted television programs, video
tapes, or other materials may
infringe on the rights of copyright
owners and violate copyright laws.
• These instructions show you how to
copy tapes using two VCRs like
yours. Different VCRs may operate
differently.
6
7
Use the SPEED button to select SP, LP, or SLP at VCR 2.
Press the PLAY button on VCR 1 and the REC(ord)/O TR
button on VCR 2 at the sam e tim e.
To stop recording, press the STOP/EJECT button on VCR 1, then
press the STOP/EJECT button on VCR 2.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 37
Repeat Play 37
Follow the steps below to make the VCR play a tape over and
over.
1
1
Press the VCR button.
2
5
8
0
3
6
1
4
7
2
Press the MENU button.
9
SELECT op CHOOSE
B
+100
→ PROGRAM
VCR SET UP
TUNER SET UP
SET CLOCK
PLAY
TO END PUSH EXIT
3
5
4
REW
F.FWD
STOP
3
Press the PLAY/o button or the STO P/p button to select
VCR SET UP, then press the F.FW D/B button.
2
6
SELECT op CHOOSE
B
→ REPEAT PLAY
ON SCREEN MODE
LANGUAGE
OFF
VCR PLUS+ REF. MAP
TO END PUSH EXIT
4
Press the PLAY/o button or the STO P/p button to select
REPEAT PLAY.
5
Press the F.FW D/B button so that O N appears beside
REPEAT PLAY.
6
Press the STATUS/EXIT button. Now, when a tape has fin-
ished playing, the VCR will rewind it and start playback again.
Helpful Hints
• To cancel Repeat Play, follow steps
1 - 4 above. At step 5, press the
F.FWD/B button so that OFF
appears beside REPEAT PLAY. Press
the STATUS/EXIT button.
• The real-time counter memory does
not function during Repeat Play.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 38
38 Real-Time Counter Memory
Follow the steps below to reset the real-time counter to zero at a
tape location you want to refer to later.
1
Play, fast forward, or rewind a tape to the location that
you would like to refer to later. Press the STO P/p button
to stop the tape.
2
5
8
0
3
6
1
4
7
2
9
Press the STATUS/EXIT button to see the status display.
+100
STOP
1:08PM
CH10
PLAY
5
3
REW
F.FWD
SLP
1 : 23 : 45
1
4
2
STOP
3
W hile the status display is on-screen, press the CLEAR
button to reset the real-tim e counter to zero.
STOP
1:08 PM
CH10
SLP
0 : 00 : 00
4
W hile the real-tim e counter is on-screen, press the MEM-
O RY button so that M appears beside the counter.
STOP
1:08 PM
CH10
SLP
M
0 : 00 : 00
Helpful Hints
• The MEMORY button does not
function if REPEAT PLAY is set to
ON. Details are on page 37.
5
To go to a tape location where the real-tim e counter was
reset to zero, press the REW (ind)/{ button or the
F.FW D/B button when playback is stopped.
When the tape reaches the point at which the counter was set to
zero, the tape will stop.
• To erase a real-time counter memo-
ry, press the MEMORY button until
the M disappears from the screen.
• You may only set the real-time
counter to zero at one location at a
time. If you try to set the real-time
counter to zero at a second loca-
tion, the previous real-time counter
to zero setting will be erased.
Press the PLAY/o button to watch the tape.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 39
Special Effects Playback 39
Forward and Reverse Searching (SP/LP/SLP)
1
During tape playback, press and release the F.FW D/B
button or the REW (ind)/{ button. A fast forward or reverse
picture search will begin.
2
5
8
0
3
6
1
4
7
2
To return to playback, press the PLAY/o button.
9
+100
Super High Speed Searching (LP/SLP)
1
PLAY
During tape playback, press the F.FW D/B button or the
REW (ind)/{ button, then press again. The VCR will now
search in super high speed.
REW
F.FWD
STOP
2
To return to norm al playback, press the PLAY/o button.
Viewing a Still Picture
1
During tape playback, press the PAUSE/STILL button. A
still picture will appear on-screen.
2
To release the still picture and return to playback, press
the PLAY/o button.
Helpful Hints
• Still mode will automatically switch
to Stop mode after five minutes to
protect the VCR and the tape from
damage.
• SP/LP/SLP means this feature will
work with tapes recorded in
Standard Play, Long Play, or Super
Long Play.
• LP/SLP means this feature will work
with tapes recorded in Long Play or
Super Long Play. For details about
tape speed, see pages 30 and 44.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 40
40 Automatic Operation Features
The following playback features will always operate.
Autom atic Playback
When you put a tape in the VCR, the power will come on auto-
matically. If the tape’s record tab is missing, playback will begin.
If a timer recording is set, the power will not come on automati-
cally when you insert a tape with the record tab intact.
If a timer recording is set and the VCR power is off, the VCR will
eject the tape if the record tab is missing.
Autom atic Rewind, Eject, O ff
When a tape is played, fast forwarded, or recorded to its end, the
VCR will rewind the tape, stop, eject the tape, then turn itself off.
If the real-time counter memory is set, the VCR will only rewind
to the point at which the counter is set to zero, then stop. The
VCR will not eject the tape automatically or shut itself off.
Tape Eject
A tape can be ejected with the VCR power on or off (but the
VCR must be plugged in). If a timer recording is set, a tape can
only be ejected with the power on. Make sure you insert a tape
and turn off the VCR power for the timer recording.
Autom atic Tracking Adjustm ent
The VCR adjusts tracking automatically to give you the best possi-
ble picture quality. With some recordings, however, you may get a
better picture using the manual tracking controls (see below).
Tracking is returned to automatic tracking when a tape is inserted
or when the STOP/p button is pressed.
Manual Tracking
To manually adjust the tracking during playback, press the CHAN-
NEL o/p buttons on the VCR. (The CHANNEL o/p buttons
on the remote control will not adjust tracking.)
You cannot manually adjust the tracking of a Still picture.
Tracking will return to Automatic Tracking Adjustment when you
press the STOP/p button or insert a tape.
Before
After
Tracking
Adjustm ent
Tracking
Adjustm ent
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 41
Specifications 41
Video Heads
Two heads
Video Signal
EIA standards; NTSC color
Antenna
VHF/UHF – 75 ohm external antenna terminal
VHF O utput Signal
Channel 03 or 04 (switchable)
75 ohms unbalanced
Power Requirem ent
120V AC; 60Hz
Power Consum ption
16W
O perating Tem perature
41°F (5°C) to 104°F (40°C)
Relative Hum idity
10% to 80%
W eight
5.51 lbs. (2.5 kg.)
Dim ensions
14-3/16” (W) x 3-1/16” (H) x 10” (D)
(360 mm x 92mm x 230mm)
Tuner Broadcast Channels
VHF 2-13, UHF 14-69
Cable TV Channels
2 – 13
Midband: A – 1
Superband: J – W
Hyperband: A-5 – A-1
Special Channel: 5A
Ultraband: 37 – 94, 100 – 125
NOTE: Designs and specifications are subject to change without notice.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 42
42 Helpful Hints
If you are having problems with your product, check this list of problems and possible solutions before
requesting service. You may be able to solve the problem yourself.
If you need to call a customer service representative, please know the model number and serial number of
your product before you call. This information is displayed on the back of the product. Also, please take a
moment to identify the problem you are having, and be prepared to explain this to the representative. If
you believe the representative will need to help you with operations, please stay near the product. Our
representatives will be happy to assist you.
No power
• Make sure the power plug is completely connected to an AC (alternating current) outlet.
• Make sure the power is turned on.
Power Failure
• Timer recordings and the clock setting may be lost if the power fails for more than one minute. See page
15 to reset your clock. See pages 28 - 35 to reprogram your timer recordings.
A TV program cannot be recorded.
• Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if
applicable) (pages six - 10).
• Make sure the tape has a record tab (page five).
• Check the TV/VCR position (page 22).
• Check the CH3/CH4 switch (pages six - nine).
The VCR will not perform a tim er recording.
• Make sure the recording start and stop times are set correctly (pages 28 - 35).
• Make sure a tape is in the VCR and the tape has a record tab (page five). If, after programming a timer
recording, you turn off the VCR power without putting a tape in the VCR, the Timer light will blink.
• If the record tab on a tape is missing, the VCR will eject the tape. The Timer light will blink.
• Make sure the VCR power is off.
• Make sure the clock is set (page 15).
• The VCR may not perform or continue a timer recording if a power interruption of more than one
minute occurs.
• If you have a Cable Box/Direct Broadcast System, timer recordings are programmed differently. (See
page eight for details.)
• Finish programming a timer recording at least five minutes before the recording is set to begin.
• 12 p.m. is noon; 12 a.m. is midnight.
There is no playback picture or the playback picture is noisy or contains streaks.
• Make sure the TV is on the same channel as the VCR’s CH3/CH4 switch.
• Make sure the VCR is in VCR position. (The VCR light will appear on the display panel.)
• Make sure channel 03 or 04 is properly adjusted at the TV.
• Adjust the tracking (page 40).
The VCR cannot be controlled with the rem ote control.
• Press the VCR button, then try the other VCR feature buttons.
• Make sure the VCR light appears on the display panel. If it does not, press the VCR/TV button once.
• Aim the remote control directly at the VCR’s remote sensor (page 22).
• Remove all obstacles between the remote control and the VCR.
• Inspect and/or replace the batteries in the remote control (page five).
The Num ber buttons won’t work for channels above 69.
• Select CABLE TV at the TUNER SET UP menu (page 12), then let the VCR set up the channels.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 43
Helpful Hints (cont’d) 43
TV program s cannot be watched norm ally.
• Put the VCR in TV position. (Press the VCR/TV button so that the VCR light disappears from the display
panel. For details see page 22.)
• Check the connections between the VCR, TV, antenna/cable, and Cable Box/Direct Broadcast System (if
applicable). (See pages six - 10 for details.)
Tape cannot be inserted.
• Insert the tape, window side up, with the record tab facing you.
• Make sure a tape isn’t already in the VCR by pressing the STOP/EJECT button on the VCR.
• Gently push on the center of the tape when putting it in the VCR. Never force the tape into the VCR.
• If a timer recording is programmed and the VCR power is off, you can not insert a tape without a
record tab.
Tape cannot be rem oved.
• Make sure the power plug is completely connected to a power outlet.
• You have set a timer recording. Turn the VCR power on, then eject the tape. Be sure to insert a tape
and turn off the power for your timer recording.
VCR ejects the tape when the REC(ord)/O TR button is pressed or when the VCR power is
turned off to set a tim er recording.
• Make sure the tape has a record tab (page five).
Channels above 13 cannot be received.
• Select CABLE TV at the TUNER SET UP menu (page 12), then let the VCR set up the channels.
Poor reception
• You may need to tune your TV again.
The m otor (cylinder) rotates even when the VCR is in Stop m ode.
• To enable the quick play mechanism, the cylinder will rotate for about five minutes. This is normal.
Direct Broadcast System Hookups
• Watching one TV channel while recording another may not be possible if you have a DBS hookup. You
may have to set your TV to channel 03 or 04, then make your channel selections at the DBS.
• With many DBS hookups, if you use accessory audio and video cables to connect your VCR to your TV,
you will have to put your VCR in Line Input mode (channel 00).
Line Input m ode
• If you accidentally enter Line Input mode (A/V IN will appear on your TV screen briefly), press the
CHANNEL o/p buttons or use the Number buttons to select another channel.
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 44
44 Glossary
AUDIO IN/O UT Jacks: jacks located on the back of the VCR
which are used to record audio from another source (IN) or to
send audio to another source (OUT).
Autom atic Channel Setup: process in which the VCR memo-
rizes all available channels. Then, when you press the CHANNEL
o/p buttons, you only scan through channels you receive.
Bands: settings that allow you to tune channels.
• Antenna – VHF (very high frequency; channels 2 - 13) and
UHF (ultra high frequency; channels 14 - 69).
• Cable – all standard channels can be received without a Cable
Box.
Cable Box O utput Channel: 03 or 04.
Dubbing: copying a tape using a second VCR.
Fram e: a still picture.
HQ : high quality; a feature in the VCR circuitry which provides
enhanced picture detail.
Line Input: The channel to which you set your VCR during dub-
bing (channel 00). If you select channel 00, A/V IN will appear on-
screen. If you accidentally enter Line Input mode, press the
CHANNEL o/p buttons or use the Number buttons to select
another channel.
O TR: One-Touch Recording; a timed recording that starts imme-
diately and records for 30 minutes to eight hours.
Rem ote Control: the small electronic unit that came with your
VCR; allows you to operate your VCR from a distance.
RF coaxial cable: The cable supplied with your VCR. Use it to
connect your VCR to your TV (or Cable Box or DBS). The sup-
plied cable is a snap-on type. However, you may use a screw-on
type if you prefer.
Special Effects: forward and reverse searching; a still picture.
Tape Speeds: how fast the tape travels during a recording or
playback.
• SP (standard play) – fastest tape speed (recording time for a
T120 tape is approximately two hours); best picture quality.
• LP (long play) – average tape speed (recording time for a T120
tape is approximately four hours).
• SLP (super long play) – slowest tape speed (recording time for
a T120 tape is approximately six hours).
VCR: video cassette recorder.
VIDEO IN/O UT Jacks: jacks located on the back of the VCR
which are used to record video from another source (IN) or to
send video to another source (OUT).
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 45
Limited Warranty 45
VIDEO CASSETTE RECORDER
90 Days Free Labor/One Year Parts Exchange. This product must be carried in for repair.
WHO IS COVERED?
tion will attempt to provide service (although there
may be a delay if the appropriate spare parts and
technical manual(s) are not readily available).
You must have proof of purchase to receive warran-
ty service. A sales receipt or other document show-
ing that you purchased the product is considered
proof of purchase.
MAKE SURE YOU KEEP...
Please keep your sales receipt or other document
showing proof of purchase. Attach it to this owner’s
manual and keep both nearby. Also keep the original
box and packing material in case you need to return
your product.
WHAT IS COVERED?
Warranty coverage begins the day you buy your
product. For 90 days thereafter, all parts will be
repaired or replaced, and labor is free. From 90 days
to one year from the day of purchase, all parts will be
repaired or replaced, but you pay for all labor
charges. After one year from the day of purchase, you
BEFORE REQUESTING SERVICE...
Please check your owner’s manual before requesting
pay for the replacement or repair of all parts, and for service. Adjustments of the controls discussed there
all labor charges.
may save you a service call.
All parts, including repaired and replaced parts, are
covered only for the original warranty period. When
the warranty on the product expires, the warranty
on all replaced and repaired parts also expires.
TO GET WARRANTY SERVICE IN U.S.A.,
PUERTO RICO OR U.S. VIRGIN ISLANDS...
Take the product to a Philips factory service center
(see enclosed list) or authorized service center for
repair. When the product has been repaired, you
must pick up the unit at the center. Centers may
keep defective parts.
WHAT IS EXCLUDED?
Your warranty does not cover:
• labor charges for installation or setup of the prod-
uct, adjustment of customer controls on the
product, and installation or repair of antenna sys-
tems outside of the product.
• product repair and/or part replacement because
of misuse, accident, unauthorized repair or other
cause not within the control of Philips Consumer
Electronics Company.
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all
implied warranties, including implied warranties of
merchantability and fitness for a particular purpose,
are limited in duration to the duration of this
express warranty. Because some states do not allow
limitations on how long an implied warranty may last,
this limitation may not apply to you.)
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation
to enable it to operate in any country other than
the country for which it was designed, manufac-
tured, approved and/or authorized, or repair of
products damaged by these modifications.
• incidental or consequential damages resulting from
the product. (Some states do not allow the exclu-
sion of incidental or consequential damages, so
the above exclusion may not apply to you. This
includes, but is not limited to, prerecorded mater-
ial, whether copyrighted or not copyrighted.)
• damage caused by the use of non-VHS tapes or
tapes that have not been tested and labeled for
use in two, four, six, and eight hour VHS
recorders.
TO GET WARRANTY SERVICE IN CANADA...
Please contact Philips at:
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
(In Canada, this warranty is given in lieu of all other
warranties. No other warranties are expressed or
implied, including any implied warranties of mer-
chantability or fitness for a particular purpose. Philips
is not liable under any circumstances for any direct,
indirect, special, incidental, or consequential damages,
howsoever incurred, even if notified of the possibility
of such damages.)
REMEMBER...
Please record below the model and serial numbers
found on the product. Also, please fill out and mail
your warranty registration card promptly. It will be
easier for us to notify you if necessary.
• a product that is used for commercial or institu-
tional purposes (including but not limited to rental
purposes).
WHERE IS SERVICE AVAILABLE?
MODEL # __________________________________
SERIAL # __________________________________
Warranty service is available in all countries where
the product is officially distributed by Philips
Consumer Electronics Company. In countries where
Philips Consumer Electronics Company does not dis-
tribute the product, the local Philips service organiza-
This warranty gives you specific legal rights. You may
have other rights which vary from state to state.
Philips Service Com pany, P.O . Box 555, Jefferson City, Tennessee 37760, (423) 475-8869
EL4946E007 / MAC 6108/ 1-97
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 46
46 Index
ac power cord.................................23
accessories .......................................48
ant(enna) in jack ................6 - 10, 23
audio in/out jacks.......10, 23, 36, 44
automatic
number buttons ..............................18
timer
light ...............................................21
recording
cancelling................................31
checking..................................31
setting ............................28 - 30
with vcr plus+ programming
system............................32 - 35
tracking..............................................40
tv
on-screen status displays..............20
one-touch recording......................27
out jack.....................................6-9, 23
playback .......................................40
rewind, eject, off........................40
pause button....................................22
pause/still button.............................19
play/K button ....................18, 24, 39
playing................................................24
power
button....................................18, 22
cord ..............................................23
pwr.(power) light............................21
batteries ..............................................5
cassette compartment ...................21
cassette-inside light ........................21
ch3/ch4 switch ........................6-9, 23
channel
button......................................5, 19
controls..........................5, 18 - 19
hookups ...................................6-10
position.................................19, 22
above 100....................................18
adding...........................................13
deleting ........................................13
reviewing .....................................14
setup....................................11 - 14
o/p buttons ...............19, 22, 40
clear button...............................19, 38
clock display.....................................21
clock setting.....................................15
connections ...............................6 - 10
contents, table of..............................4
controls
real-time counter............................38
rear panel .........................................23
rec/otr button ...................18, 22, 25
rec(ord) light....................................21
recording
vcr
button......................................5, 19
light ...............................................21
plus+ button........................18, 34
plus+ programming
basic..............................................25
one channel/
watching another.......................26
timer ....................................28 - 31
with the vcr plus+
system .................................32 - 35
position.................................19, 22
vcr/tv button.............................19, 22
video
in/out jacks.............10, 23, 36, 44
volume o/p buttons.....................19
programming system .......32 - 35
remote control
remote ................................18 - 19
vcr ........................................22 - 23
counter only mode.........................22
buttons................................18 - 19
sensor...........................................22
using................................................5
repeat play........................................37
rerecording ......................................36
rew(ind)/s button..................18, 22
rf coaxial cable ........................6-9, 36
warranty............................................45
daylight-saving time ........................16
display panel.....................................21
duplication........................................36
eject button......................................19
erase prevention ...............................5
safety precautions.............................3
searching...........................................39
sensor (remote)..............................22
slp ..........................................30, 44
f.fwd/B button..................19, 22, 39
front panel........................................22
sp
..........................................30, 44
glossary..............................................44
speed button....................................18
standard play.............................30, 44
status display....................................20
status/exit button.....................18, 20
stereo TV hookups ........................10
still picture........................................39
stop/L button..................................19
stop/eject button ............................22
super high speed searching ..........39
super long play .........................30, 44
helpful hints.............................42 - 43
hookups
with cable box/dbs ..................8-9
with stereo tv.............................10
without cable box/dbs............6-7
language selection....................11, 17
line input mode ...............36, 43 - 44
long play.....................................30, 44
lp
..........................................30, 44
table of contents...............................4
tape
memory button........................18, 38
menu button ....................................18
mute button.....................................19
duplication...................................36
eject .......................................19, 43
speed .....................................30, 44
time (setting)....................................15
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
VRZ222 layout 4/8/99 10:19 PM Page 48
Check to be sure the items on this page are packed
with your VCR. These accessories are provided to help
you use or set up your VCR.
Rem ote Control 4835 218 37212
Two AA Batteries 4835 138 17012
RF Coaxial Cable, 75 ohm 4835 323 27011
If any of these items are not included, or if you need
to replace an item, contact Philips Service Company
at the address below.
Philips Service Company
P.O. Box 967
Greeneville, TN 37744-0967
Or, call 1-800-851-8885.
IB7982E001
Printed In China
0VMN02054 / H1620UD * * * * *
Download from Www.Somanuals.com. All Manuals Search And Download.
|