Philips Network Card Network Adaper User Manual

Net 1Card IB 2/15/00 12:17 PM Page 1  
Professional Color Television  
NET1CARD  
®
T E L E V I S I O N  
O W NERS  
MANUAL  
AND  
SET-UP GUIDE  
IndustryStandards  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 4  
INTRODUCTION  
REMOTE OPERATION  
isted below is a brief description of the TH374AH  
remote control. You need one remote control  
The Net1Card is a network television systems control  
SmartCard that is designed to work with Philips  
L
SmartCard televisions in a balanced RF distribution sys-  
tem. The Net1Card allows an individual with a unit set in  
the Transmitting mode to control all televisions, up to 8  
zones of televisions, or a single television, all set in the  
Receive mode. The controls include turning the sets on,  
setting the volume, and tuning to a specific channel for  
live or prerecorded messages or programs. Any Net1Card  
can be set up to transmit or receive.  
(sold separately) to setup and operate the Net 1Card.  
Only buttons important to Net1Card are described.  
RECALL - Press this button to  
bring up the closed caption  
mode or to exit Net1Card  
menus.  
SLEEP - In the Consumer mode, press  
this button to select the amount of time  
you want before the TV turns off.  
SELECT (M) - In  
the Consumer  
mode, press this  
button to bring up  
the on-screen menu  
options. Also may  
CURSOR KEYS -  
Press these buttons  
(▲ ▼ ᮣ ᮤ ) to  
scroll or move  
The Net1Card allows the individual with the Transmitter  
unit the option to lock out the Receiver units so that the  
power, volume, or channels cannot be changed until they  
are restored by the Transmitter unit. All of this is done in  
a matter of seconds by using an optional T374AH IR  
remote control device. (See page 5.) Other features  
include the ability to change channels for different mes-  
sages, turn off all receiver televisions from a single loca-  
tion, send different messages or programs to different  
groups or individual sets. The Net1Card is easy to install,  
set up, and operate. The Net1Card also has the ability to  
poll an individual television to ensure correct systems  
operation.  
through the on-  
screen menu or to  
be used to advance  
SLEEP  
RECALL  
adjust the picture in  
the cursor.  
certain features.  
-
+
M
A/CH - Press this  
button to toggle  
between the present  
and last viewed  
channels.  
MUTE - Press this  
button to turn the  
sound OFF on the  
TV. Press again to  
return the sound to  
its previous level.  
A/ CH  
VOL  
CH  
MUTE  
CH(annel) - Press  
this button to scroll  
through all available  
channels.  
A
B
C
F
D
VOL(ume) - Press  
this button to adjust  
the sound level of  
the TV.  
E
G
ENTER  
D & F - Press the  
the D button to select  
features under each  
specific Net1Card  
mode. Press the F  
button to display the  
version of Net 1Card  
installed.  
P.PREF  
1
4
3
6
2
5
The Net1Card also has composite video input, an S-  
Video input, two audio inputs, an RF input, a speaker  
jack and a cloning port for easy connectivity to a variety  
of media devices.  
A - Press the A but-  
ton to set a TV in  
the Net1Card  
CC  
9
8
0
7
Transmit, Receive,  
or Factory mode.  
CH GDE  
POWER  
TV  
TV  
DCM  
GUEST SETUP SETUP  
ENTER/RESET -  
In the Consumer  
mode, press this  
button to reset TV  
settings to factory.  
FEATURES  
Audio/Video Jacks for direct connections with VCRs  
(or other video accessories) for quality TV picture  
and sound playback.  
NUMBERED  
BUTTONS - Press  
these buttons to  
directly access any  
available channel.  
(If a single digit  
channel is chosen,  
press 0 first.  
Audio/Video Inputs.  
CC - Press this  
button to bring the  
Closed Captioning  
option to the  
Audio/S-Video Inputs.  
Ability to broadcast to an individual TV, to a group  
of TVs, or to all the TVs in the series.  
screen.  
Example for chan-  
nel 6; first press 0,  
then 6.) In certain  
Net1Card menus,  
use these buttons to  
make selections.  
POWER -  
Press this  
button to  
turn the TV  
ON or OFF.  
TV/GUEST - Press this button before  
trying to setup the TV after installing  
the Net1Card. If the menus do not  
come up when you press the A or D  
button, press this button and try again.  
Ability to poll individual TVs.  
Clone port for limited applications.  
4
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 6  
Unpacking  
NET1CARD ASSEMBLY  
RF Input Cable  
(In Poly Bag)  
Rear Cover in  
Bubble Pack Bag  
hen unpacking the Net1Card components  
Wfrom the box, be careful pulling the items  
out. The box is packed with three separately  
packaged items: the Net1Card Assembly Cover,  
the Net1Card Circuit and Panel Board, and the  
RF Input Cable. Unfold the cardboard holders  
and remove the circuit board. Use the following  
instructions to begin assembling the unit.  
Net1Card Circuit and  
Panel Board  
(Packed in folded  
cardboard and plastic)  
Cardboard Box  
BEGIN  
First, unplug the AC power cord from the  
power outlet. Next, on the back of the TV,  
remove the hex head retaining nut from around  
the RF IN (antenna) jack.  
Removing  
Monitor  
Cover  
Remove the hex head screws holding the  
Monitor Card cover in place. Now, slide the  
jack panel cover off. Be careful when pulling  
the cover off. Make sure the RF IN jack slides  
out of the cover, but remains attached to the  
TV.  
Back of TV  
Monitor Cover  
RF Input Plug  
Retaining Nut  
1
SMART HELP  
RF IN  
Remember to make sure you have the sup-  
plied Net1Card parts before unplugging the TV.  
You will need a hex head screw driver and a hex head  
wrench in order to do the disassembly on the back of  
the TV.  
Hex head  
screw  
Keep the hex head nut from the back of the TV.  
2
7
2
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 8  
NET1CARD ASSEMBLY  
Rear of Smart Card  
Television  
nstallation of Net1Card is easy. Remember  
Ito follow these instructions, be patient, and  
use the T374AH Set Up Remote Control (see  
T374AH Remote Control Instructions - part #  
IB7166E002 for complete details).  
CLONE  
PORT  
S
-
V
I
D
E
O
A
U
D
I
O
VIDEO  
AUDIO  
R
F
I
N
BEGIN  
Hex Head Screws  
3
Disconnect the cable from the RF IN (anten-  
na) jack inside the TV. Then, connect the cable  
onto the yellow plug farthest from the 32-pin con-  
nector at the rear of the Circuit and Panel Board.  
2
32 Pin Connector  
Guide Pin  
1
Connect the RF cable (included) onto the yel-  
low plug closest to the 32-pin connector on the  
Circuit and Panel Board. Then, connect the other  
end of the cable to RF IN jack inside the TV.  
Component  
Side Up  
2
Component  
Side Down  
CLONE  
PORT  
VIDEO  
AUDIO  
VIDEO  
AUDIO  
RF IN  
Net1Card  
1
Now, insert the Net1Card (with its compo-  
nents facing down) into the back of the TV. Line  
up and guide the 32-pin connector. Note: there are  
guide pins to help properly insert the card. Gently,  
but firmly, press the card into place.  
4
Net1Card and  
Cover Assembly  
RF IN (Antenna Jack)  
Finally, insert the RF IN jack through the  
hole on the Net1Card Assembly Cover and secure  
it in place with the hex head retaining nut. Once  
done, attach the Cover to the back of the TV using  
the hex head screws.  
Clone Port - 6 Pin  
Connector for limited  
applications.  
AUDIO / VIDEO Inputs. For  
connection to video / audio  
equipment with phono jacks.  
Speaker Jack - For con-  
necting external speakers.  
CLONE  
PORT  
S-VIDEO S-AUDIO  
VIDEO  
AUDIO  
SMART HELP  
Be sure to align the 32 pin connector before  
pressing into place. Never force the Net1Card into  
the connector. If it will not go in smoothly, realign the  
guide pins and try again. Do not use the Net1Card jacks  
to push the card assembly into place. Push on the cover  
directly behind the card itself.  
RF IN  
RF IN -  
Antenna/Cable  
75Input  
S-VIDEO / S-AUDIO Input. For con-  
nection to video / audio equipment with  
S-Video / S-Audio out jacks  
If your RF IN cable will not disconnect from the Monitor  
Cover, call (800) 851-8885 to order a replacement cable.  
8
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 10  
ANTENNA HOOKUPS  
Back of TV  
Combination VHF/UHF  
Antenna  
combination antenna receives normal  
Abroadcast channels (VHF 2-13 and UHF  
14-69). Your connection is easy since there is  
only one 75(ohm) antenna plug on the  
back of your TV - and thats where the  
antenna goes. (If you have more than one  
antenna, please refer to the diagram at the  
bottom of page 11 for additional hookups.)  
(Outdoor or Indoor)  
CLONE  
PORT  
S-VIDEO S-AUDIO VIDEO  
AUDIO  
RF IN  
300 to 75Ω  
Adapter  
(483521827003)  
1
CLONE  
PORT  
BEGIN  
DIO  
VIDEO  
AUDIO  
2
If your antenna has a round cable (75 ohm)  
on the end, then you're ready to connect it to the  
TV.  
Twin Lead  
Wire  
RF IN  
If your antenna has flat twin-lead wire (300  
ohm), you first need to attach the antenna wires to  
the screws on a 300 to 75 ohm adapter.  
Net1Card  
Jack Panel  
Round Cable  
75Ω  
Push the round end of the adapter (or anten-  
na) onto the RF IN plug on the rear of the TV. If  
the round end of the antenna wire is threaded,  
screw it down tight.  
OPTIONAL HOOKUPS  
Back of TV  
Outdoor UHF Antenna  
(Twin Lead 300 Ohm)  
CLONE  
PORT  
S-VIDEO S-AUDIO VIDE
R
F
I
N
CLONE  
PORT  
SMART HELP  
S-VIDEO S-AUDIO VIDEO  
AUDIO  
Remember, be sure to set the TV for the  
type signal you’ve connected.  
RF IN  
Round End  
Outdoor VHF  
Antenna  
(Twin Lead  
300 Ohm)  
To set the TV to select only the channel numbers  
in your area see how to “Program” or “Add”  
channels in memory.  
Net1Card  
Jack Panel  
UHF  
300  
Twin Lead  
Wire  
To order any optional accessory contact your deal-  
er or call the toll-free accessory ordering number  
(1-800-292-6066):  
UHF/VHF Combiner  
V
F
V
HF  
Outdoor VHF  
Antenna  
(Round 75Ω  
Cable)  
OR  
• UHF/VHF Combiner: (SBV1133AO1)  
• 75-300 Ohm Adapter: (SBV1113AO1)  
• 300-75 Ohm Adapter: (483521827003)  
ADAPTER  
75-300 Ohm Adapter  
75-300  
Round Cable 75Ω  
10  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 12  
CABLE TV HOOKUP  
Back of TV  
our Cable TV input into your home may be  
Ya single (75 ohm) cable, or a Converter  
Box installation. In either case the connection  
to the TV is very easy. Just put the threaded  
end of the cable signal to the TV's antenna  
plug and screw it down tight.  
CLONE  
PORT  
S-VIDEO S-AUDIO VIDEO  
AUDIO  
RF IN  
Cable TV Company  
BEGIN  
If your Cable TV signal is a single round  
cable (75 ohm) then you're ready to connect to the  
TV.  
CLONE  
PORT  
UDIO  
VIDEO  
AUDIO  
Round Cable  
75Ohm  
2
If you have a Cable TV Converter Box:  
Connect the Cable TV signal to the Cable Signal  
IN(put) plug on the Converter.  
RF IN  
OUT  
IN  
Net1Card  
Jack Panel  
Cable TV Converter Box  
Connection  
Connect the Cable TV cable to the RF IN plug  
on the TV.  
1
If you have a Cable TV Converter Box:  
Connect the OUT(put) plug from the Converter to  
the RF IN plug on the TV (connecting cable sup-  
plied with the Converter).  
OPTIONAL VCR HOOKUP  
300 to 75Ohm  
Outdoor VHF/UHF  
Adapter  
1
Antenna  
Round Cable  
75Supplied  
with VCR  
SMART HELP  
Remember, set the TV to the “Cable TV  
Mode.” Then, to select only the channel  
numbers on your Cable system see “Auto  
Program” (refer to page 34 for both features).  
OR  
OUT TO TV  
IN FROM ANT.  
Cable TV signal  
VCR  
If you use a Cable Converter box, set the TV to  
the same channel as the converter's CH 3/4 switch  
(on the rear of the converter.)  
CLONE  
PORT  
S-VIDEO S-AUDIO VIDEO  
AUDIO  
RF IN  
CLONE  
PORT  
S-VIDEO S-AUDIO VIDEO  
AUDIO  
R
F
I
N
Net1Card  
Jack Panel  
Back of TV  
2
12  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 14  
Front Control Panel of TV  
AUDIO/VIDEO INPUTS  
MENU ▲  
CH ▲  
VOL  
POWER  
ou can view the playback of VCR tapes  
Y(Video Disc Players, Camcorders, etc.) by  
using the AUDIO and VIDEO INPUT jacks  
(on the Net1Card Cover assembly).  
+
CC  
SLEEP  
2
Back of TV  
For example: Use the following steps to view  
the playback of a pre-recorded VCR tape  
Rear Jacks of  
the Net1Card  
Assembly  
BEGIN  
SMART  
PLUG  
VIDEO  
AUDIO  
VIDEO  
AUDIO  
1
VGA IN  
RF IN  
VGA OUT  
IN  
OUT  
Connect the VIDEO and AUDIO IN(put)  
jacks on the TV to the AUDIO and VIDEO  
OUT(put) jacks on the VCR.  
IN  
OUT  
A
-
-
CLONE  
PORT  
S-VIDEO S-AUDIO  
VIDEO  
AUDIO  
Press the CHANNEL button three channels  
below the lowest broadcast channel to activate the  
AUX inputs.  
RF IN  
Turn the VCR ON. Insert a pre-recorded tape  
into the VCR. Press PLAY on the VCR to view the  
tape on the TV.  
Video Plug Cable  
(not supplied)  
OUT  
AUDIO  
IN  
OUT  
ANTENNA  
OUT  
SMART HELP  
VIDEO  
IN  
ANTENNA  
IN  
Remember, when your through using the  
A/V INPUT (OUTPUT) jacks, change the  
channel number back to the desired viewing chan-  
nel (or the screen will remain blank).  
3
Audio  
RCA  
Phono  
Plug  
Cable  
(not sup-  
plied)  
Jack Panel of  
Optional Mono  
VCR  
Optional VCR  
NOTE: If you have a stereo VCR, connect only  
the red (or right) plug to the audio jack on the  
back of the Net1Card.  
14  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 16  
S-VIDEO INPUTS  
Front Control Panel of TV  
MENU ▲  
CH ▲  
VOL  
POWER  
he S(uper)-Video connection on the rear of  
Tthe TV can give you better picture detail  
and clarity, for the playback of S-VHS VCR  
tapes, rather than the normal antenna picture  
connections.  
+
CC  
SLEEP  
2
Back of TV  
Note: The VCR (or accessory device) must  
have a S-VIDEO OUT(put) jack in order for  
you to complete the steps and connections  
shown to the right.  
Rear Jacks of the  
Net1Card Panel.  
SMART  
PLUG  
VIDEO  
AUDIO  
VIDEO  
AUDIO  
1
-
-
-
BEGIN  
CLONE  
PORT  
S-VIDEO S-AUDIO  
VIDEO  
AUDIO  
Connect the S-VIDEO (S-VHS) OUT(put)  
jack from the VCR (or other source) to the V-  
VIDEO IN(put) jack on the TV.  
Normally the S-VIDEO connecting cable will be  
supplied with accessory devices supplied with a S-  
VIDEO jack.  
S-VIDEO  
Cable  
(supplied with  
optional S-  
VHS VCR)  
Audio RCA  
Phono Plug  
Cable  
RF IN  
(not supplied)  
Press the CHANNEL button two channels  
below the lowest broadcast channel to activate the  
S-VIDEO inputs/outputs.  
Turn the VCR ON. Insert a pre-recorded S-  
VHS tape into the VCR. Press PLAY on the VCR  
to view the tape on the TV.  
OUT  
OUT  
AUDIO  
IN  
OUT  
VIDEO  
IN  
ANTENNA  
S-VIDEO  
IN  
3
Jack Panel of  
Optional S-VHS VCR  
Optional S-VHS VCR  
SMART HELP  
Remember, after it is connected an easy  
way to select the S-VIDEO mode is to scan  
two channels below the lowest broadcast channel.  
NOTE: If you have a stereo VCR, connect only  
the red (or right) plug to the audio jack on the  
back of the Net1Card.  
16  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:17 PM Page 18  
COMMERCIAL SETTINGS  
COMMERCIAL SETTINGS  
ONTROL MODE allows you to setup each TV as a  
C“TRANSMITTER,” “RECEIVER,” or “FACTO-  
RY.”Since almost all the TV's in the Net1Card network  
will be receivers, the default mode is “RECEIVER.”  
nce the Net1Card is installed and the TV plugged  
Oback in, you can perform Net1Card setup opera-  
tions for the TV. You should start with the “COMMER-  
CIAL SETTINGS” menu.  
BEGIN  
BEGIN  
If not already in the “COMMERCIAL SET-  
TINGS” menu, press the A button on the remote con-  
trol. Then press the button to highlight “CONTROL  
MODE.”  
To begin setup, press the POWER button to turn  
the TV on. Then press the TV/GUEST button.  
Press the A button on the remote control. The  
“COMMERCIAL SETTINGS” menu appears. (The  
menu stays up for approximately 2 minutes.) “MODE”  
is highlighted. Press the – () or + () button to select  
“COMMERCIAL,” or “CONSUMER.” Selecting  
“CONSUMER” allows you access to the TV's “SETUP  
MENU” with a standard remote or from the front panel  
on the TV. (See page 32 for details.) “COMMERCIAL”  
is the default setting. In the Commercial mode, the TV's  
menu can only be accessed with a Setup remote control.  
Press the – () or + () button to select “TRANS-  
MITTER,” “RECEIVER,” or “FACTORY.” Select  
“TRANSMITTER” if the TV will be sending informa-  
tion to the other TVs in the Net1Card network. Select  
“RECEIVER” if the TV will be receiving information  
sent by the Transmitter TV. Select “FACTORY” if you  
want to send a signal to an individual TV to test if it is  
correctly hooked up to the system. (More on these  
modes later.)  
When finished, press the button to highlight  
“CONTROL MODE.”  
When finished, press the button to highlight  
“FRONT KEYPAD.”  
COMMERCIAL SETTINGS  
COMMERCIAL SETTINGS  
MODE  
CONTROL MODE  
FRONT KEYP AD  
COMMERCIAL  
RECEIVE  
ON  
MODE  
COMMERCIAL  
RECEIVE  
ON  
CONTROL MODE  
FRONT KEYP AD  
CA
COMMERCIAL SETTINGS  
COMMERCIAL SETTINGS  
EX
MODE  
CONTROL MODE TRANSMIT  
MODE  
CONSUMER  
COMMERCIAL  
CONTROL MODE  
RECEIVE  
FRONT KEYP AD  
CABLE  
FRONT KEYP AD  
CA
ON  
ON  
YES  
COMMERCIAL SETTINGS  
EX
MODE  
COMMERCIAL  
EXIT MENU  
CONTROL MODE  
FRONT KEYP AD  
CABLE  
FACTORY  
PRESS +/ – TO CHANGE  
ON  
YES  
EXIT MENU  
PRESS +/ – TO CHANGE  
18  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 20  
COMMERCIAL SETTING  
RECEIVER CONTROL  
RONT KEYPAD allows you to enable or disable the  
Fbuttons on the front of the TV. The default setting is  
“ON.” “CABLE” allows you to select between the cable  
“YES” or “NO.” The default is “YES.”  
nce you have completed your general selections  
Ounder the Commercial Settings menu, you must  
make specific selections. These specifics depend on  
whether you set up the TV to “RECEIVE,” “TRANS-  
MIT,” or “FACTORY.”Since “RECEIVE” is the default  
setting and since almost all the TVs in the Net1Card net-  
work with be “RECEIVErs,”those specific selections are  
explained first.  
BEGIN  
If not already in the “COMMERCIAL SET-  
TINGS” menu, press the A button on the remote con-  
trol. Then press the button to highlight “FRONT  
KEYPAD.”  
BEGIN  
If not already in the “RECEIVER CONTROL”  
menu, press the D button on the remote control. “RCVR  
GROUP IDS” should be highlighted. Receiver Group  
IDs allows you to group TVs. That way, you can send a  
message only to a group or groups of TVs and not all  
the TVs in the Net1Card network.  
Press the – () or + () button to select “OFF” or  
“ON.”  
When finished, press the button to highlight  
“CABLE.” Press the – () or + () button to select  
“YES” or “NO.” Cable should be set to the same setting  
as under the TV's “SETUP MENU.” For example, if  
the “SETUP MENU is set to “CABLE YES,” then the  
setup here should be “CABLE YES.” See page 33 for  
TV setup details. (Note: the cable setting of a  
Press the Number buttons 1 - 8 to select which  
group or groups you want this particular TV to belong  
to. Each Receiver TV in the Net1Card network can  
belong to up to eight groups. To remove a TV from a  
group, simply press that Number button again.  
Transmitter TV will override the setting of a Receiver  
TV whenever a channel is tuned.)  
For example, if you place a TV in groups 1, 4, 5, and 8,  
press the 1, 4, 5, and 8 Number buttons. If you should  
then want to remove the TV from the group 5, press the  
5 button again. The TV is now is groups 1, 4, and 8 (as  
pictured below).  
When finished, press the button to highlight  
“EXIT.” Then press the “M” button. Or you can exit by  
simply pressing the RECALL button when you’re done.  
COMMERCIAL SETTINGS  
When finished, press the button to highlight  
“RCVR SET ID.”  
MODE  
COMMERCIAL  
TRANSMIT  
ON  
CONTROL MODE  
FRONT KEYP AD  
CABLE  
YES  
EXIT MENU  
– FOR OFF / + FOR ON  
RECEIVER CONTROL  
COMMERCIAL SETTINGS  
RCVR GROUP IDS 1 - - 4 - - - 8  
MODE  
COMMERCIAL  
TRANSMIT  
ON  
CONTROL MODE  
FRONT KEYP AD  
CABLE  
RCVR SET ID  
0
EXIT MENU  
YES  
EXIT MENU  
DIGITS TOGGLE GROUP IDS  
– FOR NO / + FOR YES  
20  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 22  
TRANSMITTER CONTROL  
RECEIVER CONTROL  
nce you have completed your general selections  
Ounder the Commercial Settings menu, you must  
make specific selections. If you selected “TRANSMIT”  
(See page 19.), follow the directions below.  
CVR SET ID allows you assign a specific number to  
Ra Net1Card Receiver TV. Each Receiver TV in the  
Net1Card network should have a Set ID. This allows the  
Transmitter TV to send a specific message this TV. It also  
allows the Transmitter TV to check to make sure the TV  
is hooked to the network (more later). You can select a  
number between 0 and 32,767.  
BEGIN  
If not already in the “TRANSMITTER CON-  
TROL” menu, press the D button on the remote control.  
“ADDRESS TYPE” should be highlighted. Address  
Type allows you to select which TV(s) your message  
will be sent to. That way, you can send a message only  
to one TV (“SET”), a group or groups of TVs  
(“GROUP”), or all the TVs (“BROADCAST”) in the  
Net1Card network.  
BEGIN  
If not already in the “RECEIVER CONTROL”  
menu, press the D button on the remote control. Then  
press the button to highlight “RCVR SET ID.”  
Press the Number buttons 0 - 9 (or the + or - but-  
ton) to select a Receiver ID for the TV. To set a TV with  
a single-digit number, press one number. For example,  
for 9 press the Number button 9. For a two-digit number,  
press two numbers. For 14, press the Number button 1,  
then the 4 button.  
Press the – () or + () button to select “BROAD-  
CAST,” “GROUP,”or “SET.”  
Next, press the button to highlight “GROUP  
IDS.” If you selected “BROADCAST” from “ADDRESS  
TYPE,” “ALL SETS” appears beside “BROADCAST”  
on the next line and you go on to “RCVR POWER.”  
If you selected “GROUP,use the remote control’s  
Number buttons 1 - 8 to select one or more groups to  
send your message to. To remove a group selection,  
press that Number button again. (Note: more than one  
group can be selected.)  
When finished, press the button to highlight  
“EXIT.” Then press the “M” button. Or you can exit by  
simply pressing the RECALL button when you’re done.  
RECEIVER CONTROL  
If you selected “SET,” use the Number buttons 0 - 9 to  
select the individual TV to send your message to. For  
136, press 1, 3, then 6.  
RCVR GROUP IDS – – – – – –  
RCVR SET ID  
EXIT MENU  
0
When finished, press the button to highlight  
“RCVR POWER.”  
+/ – OR DIGITS TO CHANGE  
TRANSMITTER CONTROL  
ADDRESS TYP E BROADCAST  
BROADCAST  
RCVR P OW ER  
RCVR VOLU
ALL SETS  
CURRENT  
TRANSMITTER CONTROL  
RCVR CHAN
ADDRESS TYP E  
GROUP  
– – – – – – – –  
CURREN
RCVR LOCK
GROUP IDS  
UP DATE RC
RCVR P OW ER  
RCVR VOLUME  
TRANSMITTER CONTROL  
EXIT MENU  
ADDRESS TYP E  
SET  
0
CURRENT  
CURRENT  
PRESS +RCVRCHANNEL  
RCVR LOCKOUT  
SET ID  
RCVR P OW ER  
UP DATE RCVR T
RCVR VOLUME  
22  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 24  
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
CVR POWER allows you to turn the Receiver TVs  
R“ON,” “OFF,” or leave them at their “CURRENT”  
setting. Selecting “CURRENT” allows the Receiver TVs  
to adjust the power, even if “LOCK” is selected  
under“RCVR LOCKOUT.” The default setting is “CUR-  
RENT.”  
CVR VOLUME allows you to select the sound level  
R(0 to 63 or “CURRENT”) at which the Receiver TVs  
will broadcast you message. The default setting for both  
features is “CURRENT.”  
It is recommended that you leave the Volume setting at  
“CURRENT” when broadcasting your message. This  
does not change the level on the Receiver TVs and  
allows the Receiver TVs to individually adjust the vol-  
ume – even when the system is “LOCKED” – to the best  
volumes for the rooms the TVs are in. The numbers 0 to  
63 represent a range, with 0 equaling minimum and 63  
equaling maximum. The exact sound level will vary from  
TV to TV according to which model of TV used, as well  
as the size and acoustics of each room. The default set-  
ting is “CURRENT.”  
BEGIN  
If not already in the “TRANSMITTER CON-  
TROL” menu, press the D button on the remote control.  
Then press the button until “RCVR POWER” is  
highlighted.  
Press the – () or + () button to select “CUR-  
RENT,” “ON,”or “OFF.”  
When finished, press the button to highlight  
“RCVR CHANNEL.”  
BEGIN  
If not already in the “TRANSMITTER CON-  
TROL” menu, press the D button on the remote con-  
trol. Then press the button until “RCVR VOLUME”  
is highlighted.  
TRANSMITTER CONTROL  
ADDRESS TYP E BROADCAST  
BROADCAST  
ALL SETS  
CURRENT  
CURRENT  
RCVR P OW ER  
RCVR VOLUME  
RCV
Press the button to highlight “RCVR VOL-  
UME.” Press the – () or + () button to select  
“CURRENT,” or any number between 0 and 63. You can  
also use the Number buttons to select a number.  
TRANSMITTER CONTROL  
RCV
ADDRESS TYP E BROADCAST  
UP D
BROADCAST  
EXIT
ALL SETS  
ON  
When finished, press the button to highlight  
“RCVR CHANNEL.”  
RCVR P OW ER  
RCVR VOLUME  
CURRENT  
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
RCV
TRANSMITTER CONTROL  
ADDRESS TYP E BROADCAST  
ADDRESS TYP E BROADCAST  
RCV
ADDRESS TYP E BROADCAST  
BROADCAST  
ALL SETS  
CURRENT  
CURRENT  
CURRENT  
UNLOCKED  
BROADCAST  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
ALL SETS  
CURRENT  
0
CURRENT  
UNLOCKED  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
UP D
BROADCAST  
EXIT
ALL SETS  
OFF  
CURRENT  
CURRENT  
RCVR P OW ER  
P
RCVR VOLUME  
TRANSMITTER CONTROLNU  
+/ - OR DIGITS TO C
DIGITS TO CHANGE  
ADDRESS TYP E BROADCAST  
RCVR CHANNEL  
BROADCAST ALL SETS  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
CURRENT  
6 3  
CURRENT  
UNLOCKED  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
UNLOCKED  
PRESS +/ - TO CHANGE  
+/ - OR DIGITS TO CHANGE  
24  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 26  
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
CVR CHANNEL allows you to turn the Receiver TVs  
Rto the channel you select or leave them at their  
“CURRENT” setting. Leaving them at “CURRENT”  
allows the Receiver TV to change channels, even the sys-  
tem is “LOCKED.” The default setting is “CURRENT.”  
CVR LOCKOUT allows you to lock the Receiver  
RTVs so that they can only be adjusted by the  
Transmitter TV. Or you can leave the Receiver TVs  
“UNLOCKED,” so that they can be adjusted at each  
TV. The default setting is “UNLOCKED.”  
“UPDATE RCVR TVS” transmits all your selections to  
the Receiver TVs.  
BEGIN  
If not already in the “TRANSMITTER CON-  
TROL” menu, press the D button on the remote con-  
trol. Then press the button until “RCVR CHAN-  
NEL” is highlighted.  
BEGIN  
If not already in the “TRANSMITTER CON-  
TROL” menu, press the D button on the remote con-  
trol. Then press the button until “RCVR LOCK-  
OUT” is highlighted.  
Press the – () or + () button to select “CUR-  
RENT,” channels 1 to 125 (if Cable mode is selected),  
“AUX,”or “S-VIDEO,” or channels 2 - 69 (if Cable  
mode is not selected). You can also use the Number but-  
tons to select a number. If broadcasting from a VCR or  
Camcorder, select “AUX” or “S-VIDEO,” depending on  
how it is hooked up. See pages 14 - 17 for details.  
Press the – () or + () button to select  
“UNLOCKED” or “LOCK.”  
Next, press the button to highlight “UPDATE  
RCVR TVS.” Press the – () or + () button to send  
all the commands you have selected. You must com-  
plete “UPDATE RCVR TVS” or the Receiver TVs will  
not be updated.  
When finished, press the button to highlight  
“RCVR LOCKOUT.”  
Note: if you select “LOCK” in “RCVR LOCKOUT,”  
both “ADDRESS TYPE” and “GROUP IDS” will be  
highlighted in yellow and cannot be changed until the  
TVs are “UNLOCKed” or “RESTOREd”. (For options  
under “RCVR LOCKOUT,” see page 28.)  
TRANSMITTER CONTROL  
ADDRESS TYP E BROADCAST  
BROADCAST  
ALL SETS  
CURRENT  
CURRENT  
CURRENT  
UNLOCKED  
When finished, press the button to highlight  
“EXIT.” Then press the “M” button. Or you can exit by  
simply pressing the RECALL button when you're done.  
YOU CAN NOW TRANSMIT YOUR MESSAGE.  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
ADDRESS TYP E BROADCAST  
* * * (P –C)  
CTRL LOCK* * *  
ALL SETS  
ON  
BROADCAST  
ALL SETS  
ON  
+/ - OR DIGITS TO ADDRESS
BROADCAST  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
TYP E BROADCAST  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
BROADCAST  
ALL SETS  
CURRENT  
CURRENT  
4 0  
CURRENT  
4 0  
CURRENT  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
4 0  
LOCK  
LOCK  
UNLOCKED  
PRESS +/ - TO CHANGE  
PRESS +TO UPDATE RCVRS  
+/ - OR DIGITS TO CHANGE  
26  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 28  
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
f you select “LOCK” under “RCVR LOCKOUT,”  
Iyou have a couple of options in regards to “RCVR  
POWER,” “RCVR VOLUME,” and “RCVR CHAN-  
NEL.” Discussed below are the options.  
nce you have transmitted your message, you will  
Oprobably want to return control of the Receiver TVs  
back to those TVs. If you selected “UNLOCKED” from  
the ”RCVR LOCKOUT”sub-menu, then each TV has to  
be reset at that TV. However, if you selected “LOCK,”  
the locked TVs can be restored to their previous power,  
channel, and cable settings from the Transmitter TV.  
OPTION 1: If you selected a setting (other than “CUR-  
RENT”) for any of the three categories – Power,  
Volume, Channel – the Receiver TVs will be locked  
into those settings and can only be changed by the the  
Transmitter TV. Also, “P,” “V,” or “C” will appear at the  
top of the menu indicating that Power, Volume, or  
Channel has been locked. You can lock one, two, or all  
three. For example, if you set all TVs to “RCVR  
POWER ON,” “RCVR VOLUME 35,” and “RCVR  
CHANNEL 40,” then all TVs will power on, set their  
volumes at 35, and tune to Channel 40. Also, none of the  
Receiver TVs can be adjusted, except by you, and you  
can even make changes without releasing the lock.  
BEGIN  
If not already in the “TRANSMITTER CON-  
TROL” menu, press the D button on the remote control.  
Then press the button until “RCVR LOCKOUT” is  
highlighted.  
Press the – () or + () button until “RESTORE”  
is selected. (Note: you can also select “UNLOCK” from  
this menu. Doing so, releases the Transmitter TV’s lock  
on all Receiver TVs, but does not retore the Receiver  
TVs to their previous settings.)  
TRANSMITTER CONTROL  
Press the button until “UPDATE RCVR TVS” is  
highlighted. Then, press the – () or + () button.  
“CURRENT” will appear beside “RCVR POWER” and  
“RCVR CHANNEL.” The TV’s power, channel, and  
cable are now restored to their previous settings.  
* * * (P VC)  
CTRL LOCK* * *  
BROADCAST  
RCVR P OW ER  
RCVR VOLUME  
ALL SETS  
ON  
3 5  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
4 0  
LOCK  
Receiver Volume will have to be adjusted at each TV.  
PRESS +TO UPDATE RCVRS  
When finished, press the button to highlight  
“EXIT.” Then press the “M” button. Or you can exit by  
simply pressing the RECALL button when you’re done.  
OPTION 2: If you selected “CURRENT” for any or all of  
the settings, the Receiver TVs can make adjustments to  
either Power, Volume, or Channel. For example, if you  
left “RCVR VOLUME” at the default “CURRENT,”  
then the Receiver TVs could be adjusted at the TV to the  
best volume for the model of TV and the location.  
TRANSMITTER CONTROL  
* * * (P –C)  
CTRL LOCK* * *  
ALL SETS  
ON  
BROADCAST  
RCVR P OW ER  
RCVR VOLUME  
CURRENT  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
4 0  
RESTOR
TRANSMITTER CONTROL  
TRANSMITTER CONTROL  
* * * (P –C)  
CTRL LOCK* * *  
ALL SETS  
ON  
ADDRESS TYP E BROADCAST  
BROADCAST  
RCVR P OW ER  
RCVR VOLUME  
BROADCAST  
ALL SETS  
CURRENT  
CURRENT  
CURRENT  
UNLOCKED  
PRESS +TO UPDATE RCVRS  
RCVR P OW ER  
RCVR VOLUME  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
CURRENT  
RCVR CHANNEL  
RCVR LOCKOUT  
UP DATE RCVR TVS  
EXIT MENU  
4 0  
LOCK  
PRESS +TO UPDATE RCVRS  
PRESS + TO UPDATE RCVRS  
28  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 30  
TELEVISION OPERATION  
FACTORY TEST MENU  
nce you have completed your general selections  
Ounder the Commercial Settings menu, you must  
make specific selections. If you selected “FACTORY”  
(See page 19.), follow the directions below.  
BEGIN  
Press the POWER button to turn the TV ON.  
Press the VOLUME UP () or DOWN ()  
BEGIN  
button to adjust the sound level.  
If not already in the “FACTORY TEST MENU,”  
press the D button on the remote control. “RCVR SET  
ID” should be highlighted.  
Press the CHANNEL UP () or DOWN ()  
button to select TV channels.  
Press the – () or + () button to select the number  
of the Receiver TV you want to poll. You can also use  
the Number buttons to select a number. For example,  
select number 40.  
The TELEVISION CONTROL PANEL  
MENU Button - Brings the on-screen menu up and allows  
the user to scroll thru the options.  
SLEEP Button - With the Net1Card assembly installed, the  
Sleep option at the television control panel is rendered inopera-  
ble.  
Next, press the button to highlight “POLL  
RECEIVER TV.Then, press the + () button to poll  
the TV you selected. If the set is connected to the  
Net1Card network (and even if it’s turned off) you will  
receive a message saying “RESPONSE FROM SET 40.”  
If the set with the number 40 is not connected, the mes-  
sage will read “NO RESPONSE FROM RCVR.”  
MENU Button - Will clear the screen when the on-screen  
menu is visible.  
CC Button - Will bring up the Closed Captioning options.  
Repeated pressing of this button will allow the user to change  
those options.  
CHANNEL Buttons - Use these buttons to scroll thru  
available channels. These buttons will also allow you to scroll  
thru the on-screen menu options when displayed.  
If you receive a “RCVR RESPONSE INVALID” mes-  
sage, see page 39.  
VOLUME (- or +) Buttons - Use these buttons to  
increase or decrease the audio level output of the TV. The (-) or  
(+) function for these buttons is to select certain options from  
within the on-screen menu.  
When finished, press the button to highlight  
“EXIT.” Then press the “M” button. Or you can exit by  
simply pressing the RECALL button when you’re done.  
POWER Button - Toggle between turning the TV ON and OFF.  
FACTORY TEST MENU  
RCVR SET ID  
4 0  
MENU ▲  
CH ▲  
VOL  
POWER  
P OLL RECEIVER TV  
EXIT MENU  
CC  
SLEEP  
+/ – OR DIGITS TO CHANGE  
FACTORY TEST MENU  
3
1
2
RCVR SET ID  
P OLL RECEIVER TV  
EXIT MENU  
4 0  
Note: The KEYBOARD Buttons can be controlled using the  
“FRONT KEYPAD” feature within the “Commercial Settings”  
menu (refer to page 18 for more details).  
PRESS + TO POLL  
31  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 32  
ON-SCREEN MENU CONTROLS  
TYPICAL TV FEATURES  
epending on the model of your television and its  
Dfeatures, some or all of the display functions and  
features described below will be valid. Remember, the TV  
must be in the Consumer mode to bring up the “SETUP  
MENU.” This can be selected by pressing the A button  
on the optional T374AH remote, then selecting  
ON-SCREEN MENU CONTROLS  
ccess to Net1Cards internal “COMMERCIAL  
ASETTINGS,” “RECEIVER CONTROL,” “TRANS-  
MITTER CONTROL,”and “FACTORY TEST MENU”  
can only be gained with the optional T374AH remote.  
Net1Card has two different operation modes: Consumer  
and Commercial. In the Consumer mode, the TV's  
“SETUP MENU” can be accessed by pressing the  
Menu button on either a standard remote control or on  
the TV's front keypad (if the keypad is enabled). In the  
Commercial mode, the “SETUP MENU” can only be  
accessed using a Setup remote control (T374AH).  
Consumer mode from the Net1Card “COMMERCIAL  
SETTINGS”menu. Commercial mode is the default selec-  
tion. (See page 18 for details.)  
SETUP MENU  
BRIGHTNESS  
PICTURE  
COLOR  
TINT  
SHARPNESS  
CABLE  
PICTURE ADJUSTMENTS  
DESCRIPTION OF FEATURES  
Color Adjustments - Press the (+) or  
(-) button to adjust the brightness to  
the desired level.  
Press the (+) or (-) button to adjust the  
picture to the desired level.  
Press the (+) or (-) button to adjust the  
color to the desired level. Press the (+)  
or (-) to adjust the tint to the desired  
level.  
Press the (+) or (-) button to adjust the  
sharpness to the desired level.  
Volume controls - Press the (+) or (-)  
button to set the maximum allowable  
volume available from the keyboard or  
the Guest transmitter.  
Press the (+) button to disable the nor-  
mal functioning of the volume control.  
This forces the volume to the maxi-  
mum level allowed by the volume lim-  
PROGRAM  
CH ADD/DEL  
LABELS  
REMINDER  
ON CHANNEL  
POWER ON  
DISPLAYS  
KEYBOARD  
SMART SND  
INPUT  
ESP MODE  
CHAN GUIDE  
LANGUAGE  
A/V MUTE  
CHAN BLANK  
VOL FORCE  
MIN VOLUME  
MAX VOLUME  
ON VOLUME  
SPEAKER  
n the Consumer mode, you can make adjust-  
Iments to the TV picture using the TV's “SETUP  
MENU.” Follow the steps below for the proper  
procedure.  
BEGIN  
Press the SELECT (M) button on the remote  
control to see the on-screen menu.  
Press the MENU on the remote control  
repeatedly to move the highlight to the desired fea-  
ture to change or adjust.  
Press the MENU ᮤ ᮣ buttons on the remote  
control to adjust or change the highlighted feature.  
BASS BOOST  
VOLUME BAR  
EXIT  
Press the RECALL button on the remote con-  
trol to clear the screen when finished.  
iter described in the next step. In this mode the mute func-  
tion is disabled. Press the (-) button for “standard volume  
up/down,” allowing normal volume control operation.  
Press the VOLUME UP or VOLUME DOWN button to set  
maximum level available. The range is made up of 63 steps  
from minimum to maximum.  
32  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 34  
Press the (+) or (-) to choose between MAX(imum) volume  
or the TURN ON volume. Press the VOLUME UP or VOL-  
UME DOWN button to set either the MAX(imum) volume  
level available, or the set TURN ON volume level. The range  
is made up of 63 steps from minimum to maximum.  
Cable TV Mode - Press the (+) button to have the TV  
receive cable channels 1 to 125. Press the (-) button to have  
the TV receive the normal off-the-air channels 2-69.  
Auto Program - This function allows the TV to scan all the  
channels and automatically program in memory all active  
channels on the system. Press the (+) button to activate auto  
programming. Press the (-) button at any time to stop this  
function.  
Add/Delete Channels - This function allows individual  
channels to be added or deleted from memory. Tune the  
desired channel by using the CHANNEL UP/CHANNEL  
DOWN buttons or by random access, and then press the (+)  
or (-) button to either add or remove a channel from memory.  
Keyboard - The “OFF” selection lockouts or disables all  
functions from the TV’s front control panel. (This function  
can also be controlled from the Net1Card menu. If  
“FRONT KEYBOARD OFF” is selected using the  
Net1Card's “COMMERCIAL SETTINGS” menu, you can-  
not turn the keyboard “ONwith this menu selection. This  
item should be set to “ON” for Net1Card.)  
Smart Sound - The “ON” selection controls the TV volume  
to smooth out sound levels during program changes and  
commercial breaks.  
ESP Mode - The “ESP MODE” function will automatically  
turn OFF the set if it has been ON continuously for the time  
duration shown. Press the (+) button to activate the function  
and set the time limit by random access of the desired dura-  
tion (up to 99 hours). Press the (-) button for normal TV  
operation.  
Channel Guide - Press the (+) button to enable the Channel  
Guide feature. Press the (-) button to disable the function.  
Labels - This function will give a name, up to eight charac-  
ters, to a channel. Press the (-) button to delete any existing  
label. Press the (+) button to activate this function. Once in  
modification display, a cursor will point to the position on  
the label. The Menu ▲▼ buttons (on the T374AH remote)  
will scan through the available character set. The (+) and (-)  
buttons will move the cursor to the next position on the label.  
A total of 32 channels may be labeled.  
Reminder - Press the (+) button to allow the continuous dis-  
play of the current channel number. Press the (-) button and  
the channel number will appear for only a few seconds after  
the channel change and then disappear.  
A/V Mute - The “ON” setting goes to a blank Video Blue  
background, and the TV audio is muted. “OFF” returns the  
TV to Antenna signal source screen.  
Channel Blank - The “Blanked” setting allows the viewer to  
block the picture to any channel. Press the (+) button to  
“BLANKED”, or the (-) button to “UNBLANKED”.  
Speaker - The “ON” setting is selected by pressing the (+)  
button when SPEAKER is highlighted in the menu. This will  
allow the TV speakers to operate. In the “OFF” position  
(selected by pressing the (-) button) the TV speakers will not  
work and the external speaker connection on the back of the  
TV will be operational.  
On Channel - This function will determine what channel the  
TV will tune to at initial turn ON. Tune any channel and  
press the (+) button. The TV will tune to that channel every  
time it is turned ON. Press the (-) button and the TV will, at  
turn on, tune to the last channel tuned before turn OFF.  
Power On - Press the (+) button for the “POWER FORCED  
ON” mode. This disables the normal ON/OFF control and  
the receiver will be activated once AC power is applied. The  
“Sleep Timer” function is disabled and the set may not be  
turned OFF except by removing power. Press the (-) button  
for normal “POWER ON/OFF” control. For Net1Card,  
Power On should be set to “STANDARD.”  
Bass Boost - With the BASS BOOST feature in the “ON”  
position the low frequency audio range of the TV is  
increased creating a deeper, fuller sound.  
On Volume - Sets the volume for the TV when it is first  
turned on. For Net1Card, it should be set to “STAN-  
DARD.”  
Vol Force - Forces the volume to preset levels, even when a  
lower volume level is selected. For Net1Card, it should be  
set to “STANDARD.”  
Exit - The “OFF” selection will drop the TV’s on-screen fea-  
ture list from the screen.  
Displays - The “NO DISPLAYS” function disables any on-  
screen displays, except the Sleep Timer and the Mute. Press  
the (+) button to activate this function and the (-) button for  
standard displays.  
34  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 36  
CLOSED CAPTIONING  
GENERAL INFORMATION  
INDEX  
losed Captioning allows you to read the voice con-  
Ctent of television programs on the TV screen.  
Designed to help the hearing impaired this feature uses  
on-screen “text boxes” to show dialogue and conversa-  
tions while the TV program is in progress. This feature  
will work even when the Receiver TV is “LOCKED.”  
Antenna Connections . . . . . . . . . . . . . . . . . . . .10-11  
Assembly of Net1Card . . . . . . . . . . . . . . . . . . . . .6-9  
Audio Connections . . . . . . . . . . . . . . . . . . . . . .14-15  
Cable TV Connections . . . . . . . . . . . . . . . . . . .12-13  
Closed Captioning . . . . . . . . . . . . . . . . . . . . . . . . .36  
Controls/TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33  
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38  
Hookups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-17  
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37  
Input Jacks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9  
Installation of Net1Card . . . . . . . . . . . . . . . . . . . .8-9  
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4  
On-Screen Menu Displays  
BEGIN  
Press the CC button on the remote control to bring  
up the Closed Captioning on-screen display.  
Press the CC button repeatedly to select the  
desired Closed Caption mode.  
For example: CAPTION 1.  
CAPTION 1, 2, 3, or 4: dialogue (and descriptions) for  
the action on the captioned TV program shows on-  
screen.  
TEXT 1, 2, 3, or 4: often used for channel guide, sched-  
ules, or bulletin board information for CC programs.  
Commercial Settings . . . . . . . . . . . . . . . . . . . . .18  
Receiver Control . . . . . . . . . . . . . . . . . . . . . . . .21  
Transmitter Control . . . . . . . . . . . . . . . . . . . . . .23  
Factory Test Menu . . . . . . . . . . . . . . . . . . . . . . .30  
TV Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .33  
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
Remote Operation . . . . . . . . . . . . . . . . . . . . . . . . . .5  
Safety Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . .2  
S-Video Inputs . . . . . . . . . . . . . . . . . . . . . . . . .16-17  
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . .3  
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . .39  
TV Control Panel . . . . . . . . . . . . . . . . . . . . . . . . .31  
Unpacking Net1Card I . . . . . . . . . . . . . . . . . . . . .6-7  
VCR Connections . . . . . . . . . . . . . . . . . . . . . . .13-17  
Video Connections . . . . . . . . . . . . . . . . . . . . . .14-15  
Warranty Information . . . . . . . . . . . . . . . . . . . . . .40  
Note: “CAPTION 1” is the most commonly used mode  
by captioned programs.  
After making your Closed Caption mode selection  
the menu will time out and disappear from the screen  
within a few seconds.  
Closed Captioning material (if available on the current  
selected TV program) will appear on the TV screen.  
To cancel, select the OFF mode within the Closed  
Captioning feature.  
Note: Not all TV programs and product commercials are  
made for broadcast with Closed Captioning (CC) infor-  
mation included.  
Closed Captioning modes  
when pressing the CC button  
on the remote control.  
CAPTION 2 , CAPTION 3 , CAPTION 4  
Remember, if the menus do not come up when you  
press the A or D button, press the TV/GUEST button  
and try again.  
or  
Pres s CC/ STATUS to s elect  
Clos ed Captioning mode  
TEXT 1 , TEXT 2 , TEXT 3 , TEXT 4  
CAPTION 1  
or  
OFF  
37  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 38  
GLOSSARY  
Audio/Video Inputs • Connectors (phono type plugs)  
on the rear of the TV for the input of audio and video  
signals.  
TROUBLESHOOTING  
Things to try if something isn’t working.  
No menus appear when the A or D button is pressed:  
Press the TV/GUEST button and try again.  
ClonePort • The ClonePort jack is given priority over  
all functions on the Net1Card. This port is used for  
cloning purposes only. The ClonePort connector is used  
with Data Control Modules (To copy the internal memo-  
ry settings of one SmartCard television to another with  
the use of a Smart Loader).  
Cannot change channels, adjust volume, or turn TV  
on or off: Check the Transmitter TV. It may still be in  
the Locked mode. If so, see page 29.  
In Factory Test Menu (see page 30), “RCVR  
RESPONSE INVALID” message appears when  
polled: There are probably two or more Receiver TVs  
with the same ID (see page 22) and they are responding  
at the same time. You will have to find these TVs and  
change the IDs so that they are not the same.  
Coaxial Cable • A single solid antenna wire normally  
matched with a metal plug (F-type) end connector that  
screws (or pushes) directly onto a 75 Ohm input found  
on the Television or VCR.  
In the Factory Test Menu (see page 30), a TV does  
not respond when polled: Make sure that TV is set in  
the Receive mode (see page 19).  
Commercial Mode • Mode of operation to which the  
TV can be set. Generally used by technicians to setup  
the TV’s operating system.  
• Also make sure it has been setup (see page 22).  
Menu • An on-screen listing of feature controls shown  
on the Television screen that are made available for user  
adjustments.  
Receiver TVs not changing when message sent from  
Transmitter TV: Make sure the RF cables are properly  
connected (see pages 6 - 9) inside both the Transmitter  
and Receiver TVs – get a proper installer to check this.  
• Make sure the RF cables are connected snugly to the  
back of the TVs (see page 10 - 13).  
Net1Card • An optional accessory that fits into a  
SmartCard Television creating a network to transmit and  
receive video and audio.  
“Snowy” message when Net1Card engaged: Make  
sure Net1Card menu and the TV's “SETUP MENU”  
(see page 20) are both set to either “CABLE YES” or  
“CABLE NO.”  
RF Input • Or otherwise known as the Antenna Input  
on most televisions. The input to which a video signal  
(Antenna, Cable, VCR, etc.) is generally connected.  
S-Video Input • This input is used to obtain a high  
quality of video for the best possible picture viewing.  
Unable to operate the TV’s front keypad: Make sure  
the Front Keypad mode is “ON” in both the Net1Card  
menu (see page 20) and the TV’s “SETUP MENU” (see  
page 35).  
Transmitting error messages appear on the  
Transmitter TV: While there can be more than one TV  
set up as a Transmitter TV, only one Transmitter TV at a  
time can transmit a message. Make sure only one  
Transmitter TV at a time sends a message.  
38  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Net 1Card IB 2/15/00 12:18 PM Page 40  
LIMITED WARRANTY  
One Year Carry-In Exchange  
This warranty gives you specific legal rights, and you  
may also have other rights which vary from state to  
state.  
For One Year:  
For one (1) year from the date of purchase, your  
accessory will be replaced with a new, or renewed  
product (whichever is deemed necessary) if it becomes  
defective or inoperative. This is done without charge  
to you. Replacement products are warranted for the  
balance of the warranty period.  
Who is Protected?...Where?  
This warranty is extended to the original retail pur-  
chaser for products purchased and used in the U.S.A.,  
Puerto Rico and the Virgin Islands.  
What the Purchaser Must Do:  
If you require an exchange during the warranty period,  
you must take the product to the dealer from whom it  
was purchased, or ship it freight prepaid and insured  
with proof of purchase to the Philips Factory Service  
Center listed below.  
Philips Service Company, 907 Snapps Ferry Road  
Plant 2, Service Parts Warehouse 7, Greeneville,  
TN 37743-0967  
(In U.S.A., Puerto Rico and U.S. Virgin Islands, all  
implied warranties, including implied warranties of  
merchantability and fitness for a particular purpose,  
are limited in duration to the duration of this express  
warranty. But, because some states do not allow limi-  
tations on how long an implied warranty may last, this  
limitation may not apply to you.)  
®
T E L E V I S I O N  
1998 © Philips Consumer Electronics Company  
IB7975E001  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco DVR C624M C 5 06 User Manual
Pelco Satellite Radio FR8301 User Manual
Pentair Swimming Pool Pump MagicStream User Manual
Philips Cordless Telephone DECT5113L User Manual
Philips CRT Television TS2575C1 User Manual
Philips Power Supply LR03PS48C User Manual
Philips TV Receiver 29PT5631 User Manual
Polycom Cordless Telephone 72 1084 02 User Manual
Poulan Tiller 163661 User Manual
Powermate Portable Generator PM0401858 User Manual