Philips Indoor Furnishings Wall Mounting User Manual

Quick Start Guide

CONTENTS

INSTALLING LCD TV ON THE WALL . .1 TUNER MODE CONTROL . . . . . . . . . . . . . 5

UNFOLD THE BASE. . . . . . . . . . . . . . . 1 AUTO PROGRAM (SETTING UP

TV CHANNEL INSTALLATION . . . . . . . .2 CHANNELS) . . . . . . . . . . . . . . . . . . . . 5

PRESENTATION OF THE LCD TV . . . . . 2 CABLE BOX (WITH RF IN/OUTPUTS) . . 6

ACCESSORIES. . . . . . . . . . . . . . . . . . . .3 CABLE BOX (WITH AUDIO/VIDEO

BATTERY INSTALLATION . . . . . . . . . . . . 3 OUTPUTS) . . . . . . . . . . . . . . . . . . . . . 6

REMOTE CONTROL OPERATION . . . . . .3 S-VIDEO CONNECTIONS . . . . . . . . . . . 7

ANTENNA TV . . . . . . . . . . . . . . . . . . 4 HD CONNECTIONS . . . . . . . . . . . . . . 7

BASIC CABLE TV CONNECTION . . . . . 4 PC (MONITOR) INPUTS . . . . . . . . . . . 8

IMPORTANT

NOTE: This quick setup guide is used with several

diﬀerent LCD TV models. Not all features (and drawings)

discussed in this manual will necessarily match those

found with your LCD TV set. This is normal and does not

require that you contact your dealer or request service.

WARNING:TO PREVENT FIRE OR SHOCK HAZARD

DO NOT EXPOSETHIS UNITTO RAIN OR EXCESSIVE.

INSTALLING LCDTV ON THE WALL

The stand of your LCD TV complies with the VESA standard, if you intend to install the LCD TV on the wall,

please consult a professional technician for proper installing.

Wall Mounting of your LCD TV :

Put your LCD TV set on a safe and ﬂat surface, then

fold the base backward.

Note: To fold the base requires a degree fo force.

Use for the TV set a Vesa compliant wall mount (not included).

(For 20 inch: 100x100 mm)

Use for installation by a professional technician.

(20 inch: 100x100 mm)

Note: The manufacture accepts no liability, ensure installation is

done by a professional technician.

UNFOLD THE BASE

Expanding the base requires a degree of force; please use sufficient force to unfold the base.

When unfolding the base, place the TV on a flat, sturdy surface before expanding the base.

^{Download from Www.Somanuals.com}1^{. All Manuals Search And Download.}

3138 155 24532

ACCESSORIES

BATTERY INSTALLATION

When you unpack this unit, make sure it includes the

following:

Remove the battery compartment lid on

the bottom of the remote control.

Place lithium cell in the remote control.

Be sure the (+) and (-) ends of the

batteries line up as marked inside the

battery (CR2025) compartment.

Reattach the battery

compartment lid.

Owner`s Manual & Quick Start Guide

Power adapter & cable

(/79)

(/98)

Tuner L-Adapter

Warranty Card

REMOTE CONTROL OPERATION

Unused key

Press to go to previously selected channel.

Power button

Press to turn the LCD TV on or off.

Sleep button

A/CH

Press to set the LCD TV to turn itself off within a

certain time.

I-II button / Sound mode

Press repeatedly to select Mono,

Stereo, Dual I, Dual II, Nicam Mono, Nicam Stereo,

Nicam Dual I, Nicam Dual II.

Teletext keys

Smart Sound button

Picture Format button

Press repeatedly to select among the 4 settings;

Personal, Voice, Music, or Theatre.

Press the FORMAT button

repeatedly to toggle among the three screen format

sizes; 4:3, EXPAND 4:3, COMPRESS 16:9

Menu button

Press to activate onscreen menu, back to previous

level inside the onscreen menu, or press to exit the

onscreen menu.

Smart Picture button

Press repeatedly to select either

Personal, Rich, Natural, Soft, or

Multimedia picture setting.

Volume button

Press to increase or decrease the sound level

Virtual Surround button

Adds greater depth and dimension to TV sound.

Select from ON or OFF.

Mute button

Press to eliminate or restore the LCD TV sound.

Mute will appear on the screen when the sound is

muted.

Cursor Buttons

(Left, Right, Up, Down)-

Press these buttons to highlight, select, and adjust

items on the TV’s on screen menu.

Number buttons

Press the number buttons for direct access to the

TV channels. For a 2 digit channel, enter the 2nd

digit after enter 1st digit.

Channel button

Press to adjust the channel up or down.

Information button

AV button

Press to see the current channel number on the TV

screen.

Press to select the video input source:

PC, TV, AV, S-Video, HD

Download from Www.Somanuals.com. All Manuals Search And Download.

ANTENNA TV

A combination antenna receives normal broadcast channels (VHF 2–13 and UHF 14–69). Your connection is easy because there is only

one 75 Ω (ohm) antenna jack on the side of your TV, and that’s where the antenna goes.

If your antenna has a round cable (75 ohm) on the end, then

you’re ready to connect it to the LCD TV. If your antenna

has ﬂat, twin-lead wire (300 ohm), you ﬁrst need to attach

the antenna wires to the screws on a 300- to 75-ohm

�

adapter(not supplied).

Outdoor or Indoor Antenna

(Combination VHF/UHF)

DC Adapter

Connect the antenna (or adapter) to one end of the

supplied L-Adapter as shown, and connect the other end of

the L-Adapter to the TV jack on the side of the LCD TV.

Power

Cable

�

Plug the DC adapter into the DC IN 16V jack on the LCD

TV. Plug the power cable into an outlet and switch TV set on.

Run the AUTO PROGRAM function to set up the TV for the

broadcast or cable channels available in your area. If you do

not run the auto program function to set up the channels ,

your television may not operate properly.

Twin-lead

wire to

300-75�

adapter

�

Antenna

with 75 �

cable

ELPFUL

INT

• Remember, an antenna or cable TV signal must ﬁrst be connected to

your LCD TV.

• Please make sure that you have selected the TV mode with AV key

on your remote control, before installing TV channels.

BASIC CABLE TV CONNECTION

Your Cable TV input into your home may be a single (75 ohm) cable or use a cable box decoder. In either case the connection is very

simple. Follow the steps below to connect your cable signal to your new television.

Direct cable connections:

The Cable TV signal from

Cable Company

�

(75 coaxial cable)

Connect the Cable TV signal to one end of the supplied

L-Adapter as shown, and connect the other end of the

adapter to the TV jack on the LCD TV.

�

Plug the DC adapter into the DC IN 16V jack on the LCD

TV. Plug the power cable into an outlet and switch TV set on.

L Adapter

DC Adapter

Run the AUTO PROGRAM function to set up the TV for the

broadcast or cable channels available in your area. If you do

not run the auto program function to set up the channels ,

your television may not operate properly.

Power

Cable

ELPFUL

INT

• Remember, an antenna or cable TV signal must ﬁrst be connected to

your LCD TV.

• Please make sure that you have selected the TV mode with AV key

on your remote control, before installing TV channels.

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO PROGRAM (SETTING UP CHANNELS)

Your LCD TV can automatically set itself for local area (or cable TV) channels. This makes it easy for you to select only the TV stations in

your area by pressing the CH+ or CH- button.

MAIN CONTROLA

Press the MENU button on the remote control to show the

PICTURE

AUDIO

LANGUAGE

onscreen menu.

AUTO PROGRAM

MANUAL STORE

CHANNEL SETTING

FACTORY RESET

A/CH

FEATURES

INSTALL

Press the CURSOR DOWN button to

highlight the INSTALL menu.

Press the CURSOR RIGHT button

to enter the INSTALL menu.

Press the CURSOR DOWN button to

highlight the AUTO PROGRAM control.

INSTALL

LANGUAGE

AUTO PROGRAM

MANUAL STORE

CHANNEL SETTING

FACTORY RESET

START

Press the CURSOR RIGHT button to start the AUTO PROGRAM scanning

of channels.

Press the MENU button repeatedly to clear the menu from the screen, after

AUTO STORE has ﬁnished.

AUTO STORE

PLEASE WAIT

PROG.FOUND

FREQUENCY

ELPFUL

INT

MHZ

• Immediately after unpacking and plugging in your new television, run the auto

program function to set up the TV for the broadcast or cable channels available in

your area. If you do not run the auto program function to set up the channels ,

your television may not operate properly.

• After you’ve run Auto Program, check out the results. Press the CH(+) or the CH(-)

button and see which channels you can select.

• Remember, an antenna or cable TV signal must ﬁrst be connected to your LCD TV.

MANUAL STORE OF TV CHANNEL

You can also choose to tune your TV channels. Manual tuning allows you to store each programme manually.

MAIN CONTROLS

Press the MENU button on the remote

control to show the onscreen menu.

PICTURE

AUDIO

FEATURES

LANGUAGE

AUTO PROGRAM

MANUAL STORE

CHANNEL SETTING

FACTORY RESET

INSTALL

LANGUAGE

AUTO PROGRAM

MANUAL STORE

CHANNEL SETTING

FACTORY RESET

Press the CURSOR DOWN button to

highlight the INSTALL menu, then press

CURSOR RIGHT to enter.

MANUAL STORE

PROG. NO

FINETUNE

STORE

Select the MANUAL STORE, then press the CURSOR RIGHT button to

activate auto search channel frequence or press

number button to show your desired

MANUAL STORE

A/CH

XXX.XX MHZ

MANUAL STORE

PROG. NO

FINETUNE

STORE

START

channel frequence.

After the channel frequence conﬁrmed, select

PROGRAM NO. by pressing CURSOR DOWN.

MANUAL STORE

PROG. NO

FINETUNE

STORE

Press the number button or CURSOR RIGHT/LEFT to give the channel

number.

If the channel reception is not satisfactory, press CURSOR DOWN button

to highlight the FINETUNE. then press CURSOR RIGHT/LEFT to adjust.

Note: If the channel reception is satisfactory, please go to step 7.

MANUAL STORE

PROG. NO

FINETUNE

STORE

Press CURSOR DOWN to highlight STORE function. Press CURSOR

RIGHT to conﬁrm stored.

MANUAL STORE

Press the MENU button repeatedly to clear the menu from the screen.

MANUAL STORE

PROG. NO

FINETUNE

STORE

STORED

Download from Www.Somanuals.com. All Manuals Search And Download.

CABLE BOX (WITH RF IN / OUTPUTS):

Connect the Cable TV signal to the IN jack (or RF IN or CABLE

IN) on the Cable Box.

The CableTV signal from

the Cable Company

�

Connect an RF coaxial cable (not supplied) to the OUT jack (or

TO TV or RF OUT) of the Cable Box.

�

OUTPUT

CABLE

TO TV

Connect the other end of the coaxial cable to one end of the

supplied L-Adapter as shown, and connect the other end of the

adapter to the TV jack on the LCD TV.

75�

Coaxial

Cable

Plug the DC adapter into the DC IN 16V jack on the LCD TV.

Plug the power cable into an outlet and switch TV set on.

�

Set the Channel 3/4 (or Output channel) switch of the Cable Box

to 3 or 4. Set the TV to the same channel. When watching TV

programming, change channels at the Cable Box, not the LCD TV.

ELPFUL

INT

VGA

• Immediately after unpacking and plugging in your new television,

run the auto program function to set up the TV for the broadcast

or cable channels available in your area. If you do not run the auto

program function to set up the channels , your television may not

operate properly.

�

DC Adapter

• Please make sure that you have selected the TV mode with AV key

on your remote control, before installing TV channels.

Power

Cable

CABLE BOX (WITH AUDIO /VIDEO OUTPUTS):

This connection will supply stereo sound to the LCD TV.

Connect the Cable TV signal to the IN jack (or RF IN or CABLE

IN) on the Cable Box.

S -VIDEO

AUDIO

VIDEO

Using an RCA-type video cable (not supplied) connect one end of

the video cable to the Video Out jack of the Cable Box. Connect

the other end of the cable to the yellow VIDEO jack on the side

of the TV. Video cables are usually marked with yellow and are

available from Philips or electronics retailers. Video jacks on most

equipment are yellow.

�

VGA

Using RCA-type, stereo audio cables (not supplied), connect one

end of the cables to the left and right Audio Out jacks of the Cable

Box. Connect the other end of that cable to the Audio jack on the

side of the LCD TV. Audio cables are usually marked with red and

white and are available from Philips or electronics retailers. The

right audio jack is red and the left audio jack is white. Match the

cable colors to the jack colors.

Video Cable

�

DC Adapter

Audio Cable

Power

Cable

Plug the DC adapter into the DC IN 16V jack on the LCD TV.

Plug the power cable into an outlet and switch TV set on.

TV signal

Note: Use the AV button on the remote control to tune to the AV

channel for the cable box signal. Once tuned, change channels at

the cable box, not the television.

OUTPUT

�

CABLE

VIDEO

OUT

AUDIO

OUT

When you watch programs using VCR, it’s recommended to select

SOFT Mode via Smart picture.

Cable Box

Download from Www.Somanuals.com. All Manuals Search And Download.

S-VIDEO CONNECTIONS

The S-Video connection on the rear of the LCD TV can provide you

with better picture detail and clarity for the playback of accessory

sources such as DBS (digital broadcast satellite), DVD (digital video

discs), video games, and VHS VCR (video cassette recorder) tapes

than the normal antenna picture connections.

VIDEO

AUDIO

VIDEO

��

Connect an S-Video cable to the S-VIDEO jack of the other

equipment (DVD Player, Camcorder, etc.) and to the S-VIDEO jack

on the rear of the LCD TV.

�

��

Connect RCA-style audio cables (usually red and white) to the

AUDIO OUT (left and right) jacks on the other equipment.

Connect the other end of the cables to the AUDIO jack on the

side of the LCD TV.

��

Plug the DC Adapter into the DC IN 16V jack on the LCD TV.

Plug the power cable into an outlet. Turn on the LCD TV and other

equipment.

��

�

��

� ��

��

�

��

�

��

Press the AV buttons to set the LCD TV to its S-VIDEO mode.

�

Press PLAY on the other equipment to view its material on the

LCD TV.

��

�

Note:

•

The Philips LCD TV remote control can not be used to operate other video/audio

equipment.

•

The Audio jack of AV IN is shared between Video (CVBS) and S-Video signals. If Audio

and Video is connected to S-Video input, you can still hear sound if you select Video via

AV select, even there appears no image on screen.

HD CONNECTIONS

HD video input provide the highest possible color and

picture resolution in the playback of digital signal source material,

such as with DVD players. If you are using a HD (High Deﬁnition)

receiver that can transmit high deﬁnition programming, the TV can

accept those signals through the HD input located on the bottom of

the TV.

Connect the HD (Y, Pb, Pr) Video OUT jacks from the DVD player

(or similar device) to the HD VIDEO Input jacks on the bottom of

the LCD TV.

COMPONENT

VIDEO CABLES

(Green, Blue, Red)

�

Audio Cable

Power Cable

Connect the red and white AUDIO CABLES to the Audio (left

ad right) output jacks on the rear of the accessory device to the

AUDIO IN jack. Connect the other end of the cable to the Audio

jack on the rear of LCD TV.

��

Plug the DC Adapter into the DC IN 16 V jack on the LCD TV.

Plug the power cable into an outlet. Turn on the LCD TV and other

equipment.

�

COMP��

S-VIDEO VIDEO AUDIO

OUT

Press the AV button on the remote control to select HD. HD will

appear in the upper left corner on the TV screen.

�

Insert a DVD disc into the DVD player and press the PLAY button

on the DVD Player.

��

�

ACCESSORY DEVICE

EQUIPPED WITH COMPONENT

VIDEO OUTPUTS.

Note:

�

•

The Philips LCD TV remote control can not be used to operate