Register your product and get support at
HTR5224
EN User manual
3
3
3
3
3
DE Benutzerhandbuch
ES Manual del usuario
FR Mode d’emploi
NL Gebruiksaanwijzing
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Adjust sound
21
21
21
21
22
Contents
Control the volume
Select surround sound
Select double bass
1 Important
4
4
5
Select a preset sound effect
Safety and important notice
Trademark notice
7 Specifications
8 Troubleshooting
9 Glossary
23
24
25
2 Your product
Feature highlights
Product overview
6
6
6
3 Connect
9
9
Place the product
Connect speakers and subwoofer
Connect radio antenna
Connect HDMI supported devices
Connect other devices
Connect power cord
10
10
11
12
14
4 Get started
15
15
15
15
17
18
Insert the remote control batteries
Control a play source
Change speaker settings
Use Philips EasyLink
Select a play source
5 Play
19
19
19
20
Play from portable media player
Play from radio
Use sleep timer to power off
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Mains fuse (UK only)
1 Important
This Digital Receiver is fitted with an approved
moulded plug. Should it become necessary to
replace the mains fuse, this must be replaced
with a fuse of the same value as indicated on
the plug (example 10A).
Safety and important notice
1 Remove fuse cover and fuse.
Warning
2 The replacement fuse must comply with
BS 1362 and have the ASTA approval
mark. If the fuse is lost, contact your
• Risk of overheating! Never install the digital
receiver in a confined space. Always leave a
space of at least 4 inches around the digital
receiver for ventilation. Ensure curtains or
other objects never cover the ventilation slots
on the digital receiver.
• Never place the digital receiver, remote
control or batteries near naked flames or
other heat sources, including direct sunlight.
• Only use this digital receiver indoors. Keep this
digital receiver away from water, moisture and
liquid-filled objects.
dealer in order to verify the correct type.
3 Refit the fuse cover.
In order to maintain conformity to the EMC
directive, the mains plug on this product must
not be detached from the mains cord.
• Never place this digital receiver on other
electrical equipment.
• Keep away from this digital receiver during
lightning storms.
• Where the mains plug or an appliance
coupler is used as the disconnect device,
the disconnect device shall remain readily
operable.
• Visible and invisible laser radiation when open.
Avoid exposure to beam.
This product complies with the radio
interference requirements of the European
Community.
This product complies with the requirements
of the following directives and guidelines:
2004/108/EC, 2006/95/EC
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Recycling
Trademark notice
HDMI, HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI licensing LLC.
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
When you see the crossed-out wheeled bin
symbol attached to a product, it means the
product is covered by the European Directive
2002/96/EC:
Manufactured under license from Dolby
Laboratories. Dolby, Pro Logic and the
double-D symbol are trademarks of Dolby
Laboratories.
Manufactured under license under U.S. Patent
#’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762;
6,487,535 & other U.S. and worldwide patents
issued & pending. DTS and DTS Digital
Surround are registered trademarks and the
DTS logos and Symbol are trademarks of
DTS, Inc. © 1996-2008 DTS, Inc. All Rights
Reserved.
Never dispose of your product with other
household waste. Please inform yourself about
the local rules on the separate collection of
electrical and electronic products. The correct
disposal of your old product helps prevent
potentially negative consequences for the
environment and human health.
ENERGY STAR and the ENERGY STAR mark
are registered U.S. trademarks.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed of with normal household
waste.
Please inform yourself about the local rules
on the separate collection of batteries. The
correct disposal of batteries helps prevent
potentially negative consequences for the
environment and human health.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
2 Your product
Product overview
Main unit
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers; register your product
Feature highlights
a
b c d
e f gh
i
Your product supports Philips EasyLink, which
uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices
that are connected through HDMI connectors
can be controlled by a single remote control.
a
(Standby-On)
Turns on the Digital Receiver or
switches to standby mode.
•
Note
b SURR (Surround Sound)
Switches audio output to one of
• Philips does not guarantee 100%
interoperability with all HDMI CEC devices.
•
these modes: multi-channel 7.1
surround, 7-channel stereo, multi-
channel 5.1 surround, 5-channel
stereo or stereo.
Listen to rich uncompressed multi-channel
surround sound
This product supports 7.1 channels of
uncompressed audio that delivers a true-to-
life sound experience as if you are listening to
it live.
c SOUND
•
Selects a predefined sound effect.
d PROG (Programme)
•
In radio mode, resets the list of
MP3 link
preset stations: press to manually
reset; press and hold to automatically
reset.
In other source mode, accesses
or exits the audio setup mode for
speaker settings.
Simply plug your portable media player into
the MP3 LINK socket to enjoy the music in
superb sound quality.
•
Sync the audio output with the video play
Synchronise audio from this Digital Receiver
with video played from other devices by
delaying the audio output from the speakers
to match the video on the TV.
e
/
TUNING
Selects the previous or next preset
radio station.
•
•
Press and hold to start auto search.
f Display panel
g SOURCE
•
Selects a connected device to
enjoy the audio output through the
speaker system.
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
h VOLUME
Remote Control
•
Increases or decreases volume.
i MP3 LINK
a
•
Connects a portable audio player.
b
c
d
k
l
e
f
g
m
n
h
o
p
q
i
j
a
(Standby-On)
Turns on the Digital Receiver or
switches to standby mode.
•
b AUDIO SOURCE
•
Selects an audio input source.
c HDMI SOURCE
•
Selects an HDMI input source.
d RADIO
•
Switches to FM band.
e SOUND
•
•
Selects a predefined sound effect.
f
/
Selects the previous or next preset
radio station.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
g
(Mute)
Mutes or restores audio output.
•
h Numeric buttons
Enter the number of a preset radio
station.
•
i DOUBLE BASS
Turns dynamic bass enhancement on
or off.
•
j SLEEP
•
Sets a delay after which the Digital
Receiver switches to standby.
k OK
•
Confirms an entry or selection.
l
•
(Navigation buttons)
Navigates through menus.
In radio mode, press up and down to
tune the radio frequency.
In radio mode, press left or right to
start auto search.
•
•
m SURROUND
Switches audio output to one of
•
these modes: multi-channel 7.1
surround, 7-channel stereo, multi-
channel 5.1 surround, 5-channel
stereo or stereo.
n VOL +/-
•
Increases or decreases volume.
o DELETE
•
Press and hold to erase the current
preset radio station.
p BACK
•
Returns to previous step.
•
Press and hold to delete selected
station.
q AUDIO SETUP / PROGRAM
•
Accesses or exits options for audio
settings.
•
In radio mode, resets the list of
preset stations: press to manually
reset; press and hold to automatically
reset.
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Connect
Place the product
•
Place the product where it cannot be
pushed, pulled over or knocked down.
Do not place it in an enclosed cabinet.
Make sure that you have full access to the
power cord for easy disconnection of the
product from the power supply.
Make the following connections to use your
Digital Receiver.
•
Connect this Digital Receiver:
•
•
•
Speakers and subwoofer
Radio antenna
Power
FRONT
LEFT
LEFT
LEFT
BACK
SURR
CENTER
Connect other devices:
•
•
•
HDMI supported devices
Audio from TV
Audio from cable box/recorder/game
console/disc player
FRONT
RIGHT
RIGHT
BACK
RIGHT
SURR
SUBWOFER
•
Portable media player
Note
1 Place the Digital Receiver near the TV.
• Refer to the type plate at the back or bottom
of the product for identification and supply
ratings.
• Before you make or change any connections,
ensure that all the devices are disconnected
from the power outlet.
2 Place the speakers system at normal
listening ear-level and directly parallel to
the listening area.
3 Place the subwoofer in the corner of the
room or at least 3 feet away from the TV.
Tip
Tip
• Different types of connectors may be used to
connect this product to your TV, depending on
availability and your needs. A comprehensive
interactive guide to help you connect your
philips.com.
• To avoid magnetic interference or unwanted
noise, never place this Digital Receiver too
close to any radiation devices.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect speakers and
subwoofer
Connect radio antenna
FM
(75 Ω)
ANTENNA
BACK
BACK
1 Connect the FM antenna to the FM75
socket on the Digital Receiver (for some
models, this cable is already connected).
2 Extend the FM antenna and fix its ends to
the wall.
Tip
• For better FM stereo reception, connect to an
external FM antenna.
BACK BACK
1 Connect the speakers and subwoofer
to the matching sockets on the Digital
Receiver.
Note
• Ensure that the colours of the plugs and
sockets are matched.
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to HDMI devices
Connect HDMI supported
devices
Connect the HDMI or DVI compatible
devices (e.g. DVD/Blu-ray player, HDD/DVD
recorder) to this Digital Receiver to enjoy
uncompressed digital audio output.
Connect to HDTV
Connect this Digital Receiver to your High
Definition TV (HDTV) to enjoy Philips
EasyLink control capabilities. You can
synchronise operations with other HDMI
compatible devices. See ‘Get Started’ chapter
> ‘Use Philips EasyLink’ for details.
HDMI OUT
HDMI IN
1
HDMI IN
2
HDMI OUT
HDMI OUT
HDMI IN
1 Connect an HDMI cable (not supplied)
to the HDMI IN1/HDMI IN2 socket on
the Digital Receiver and the HDMI OUT
socket on the device.
1 Connect an HDMI cable (not supplied)
to the HDMI OUTon the Digital Receiver
and the HDMI IN socket on the HDTV.
Note
2 Connect an audio cable (analogue or
digital) to the AUDIO IN-AUX1/AUX2
sockets or DIGITAL IN socket on the
Digital Receiver and the corresponding
audio input sockets on the HDTV.
• To listen to the audio output from this
connection, press HDMI SOURCE repeatedly
to select ‘HDMI IN1’ or ‘HDMI IN2’.
•
See ‘Connect other devices’ chapter
> ‘Connect audio from TV’ for
details.
Note
• You can only use the Philips EasyLink control if
the connected HDTV and HDMI compatible
devices are compliant with HDMI-CEC.
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect audio from cable box/
recorder/game console/disc player
Connect other devices
Route the audio from other devices to this
Digital Receiver to enjoy audio with multi-
channel surround capabilities.
You can choose to connect to analogue
or digital sockets depending on the device
capabilities.
Connect audio toTV
Connect to analogue sockets
(also used for EasyLink control)
AUDIO IN
AUX1
AUX
2
AUDIO OUT
AUDIO OUT
1 Connect the audio cables (not supplied)
to the AUDIO IN-AUX1 sockets on the
Digital Receiver and the AUDIO output
sockets on the device.
1 Connect the audio cable (not supplied)
to the AUDIO IN-AUX2 sockets on the
Digital Receiver and the AUDIO OUT
sockets on your TV.
Note
Note
• To listen to the audio output from this
connection, press AUDIO SOURCE
repeatedly until ‘AUX1’ is displayed on the
display panel.
• To listen to the audio output from this
connection, press AUDIO SOURCE
repeatedly until ‘AUX2’ is displayed on the
display panel.
Tip
• If the TV has a digital audio output socket
(Coaxial or Optical), you can connect it to
the corresponding input socket on the Digital
Receiver for better sound quality.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect to coaxial socket
Connect to optical socket
DIGITAL IN
COAXIAL
OPTICAL
DIGITAL IN
COAXIAL
OPTICAL
DIGITAL OUT
/
/
DIGITAL OUT
1 Connect the optical cable to the
OPTICAL DIGITAL-IN socket on the
Digital Receiver and the OPTICAL/SPDIF
output socket on the device.
1 Connect a coaxial cable (not supplied) to
the COAXIAL DIGITAL-IN socket on
the Digital Receiver and the COAXIAL/
DIGITAL output socket on the device.
Note
Note
• To listen to the audio output from this
connection, press AUDIO SOURCE
repeatedly until ‘OPTI IN’ is displayed on the
display panel.
• To listen to the audio output from this
connection, press AUDIO SOURCE
repeatedly until ‘COAX IN’ is displayed on the
display panel.
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect portable media player
Connect power cord
Warning
• Risk of product damage! Ensure that the
power supply voltage corresponds to the
voltage printed on the back or the underside
of the product.
MP3
1 Connect the power cord to the socket
1 Connect a 3.5 mm stereo audio cable
(not supplied) to the MP3 LINK socket
on the Digital Receiver and the phone
socket on the portable media player (e.g.
MP3 player).
when all the required connections are
made.
» This product is ready to be set up for
use.
Note
• To listen to the audio output from this
connection, press AUDIO SOURCE
repeatedly until ‘MP3 LINK’ is displayed on the
display panel.
14 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Get started
Change speaker settings
Ideally, the distance between listening position
and all the speakers should be the same. If not,
change the speaker settings based on their
distance from the listening position to obtain
the best possible surround sound.
Insert the remote control
batteries
Note
• Switch this Digital Receiver to multi-channle
surround mode before you can change the
speaker settings.
Test and set the speaker volume
1 Press SURROUND to switch to multi-
channel surround mode.
2 Press AUDIO SETUP.
3 Press
/
until ‘TEST TONE’ is
displayed, then press OK.
» Each speaker outputs sound for 5
seconds.You can hear the volume level
set for each speaker.
1 On the back of the remote control, slide
the battery cover to remove it.
2 Insert the 2 supplied batteries (AAA). Be
sure the + and - ends of the batteries line
up with the markings inside the case.
4 Press
or VOL +/- to adjust the
volume level, then press OK.
•
The last volume setting will be
stored automatically after 5 seconds
of inactivity.
3 Slide the cover back into position.
Note
5 Repeat the above steps for other
speakers until the output level of all
speakers is equally balanced.
• Do not mix batteries (old and new or carbon
and alkaline, etc.).
• Remove batteries if they are exhausted or if the
remote control is not to be used for a long time.
• Batteries contain chemical substances, they
should be disposed of properly.
•
To return to previous step, press
BACK.
To exit the setup, press AUDIO
SETUP.
•
Note
Control a play source
• If no buttons are pressed within 2 seconds
after one speaker has been tested, the next
speaker will be tested automatically.
• Test tone is available only in Multi-channel 7.1
and Multi-channel 5.1 modes.
1 Press RADIO, AUDIO SOURCE or
HDMI SOURCE to select the source you
wish to control.
2 Adjust the volume or change the sound/
surround effect.
EN 15
Download from Www.Somanuals.com. All Manuals Search And Download.
Set the speaker delay time
Sync audio output with video play
1 Press SURROUND to switch to multi-
1 Press SURROUND to switch to multi-
channel surround mode.
channel surround mode.
2 Press AUDIO SETUP.
2 Press AUDIO SETUP.
3 Press
/
to select the speaker for
3 Press
/
until ‘AUDIO SYNC’ is
which you want to set the delay time,
then press OK.
» ‘CENTER DELAY’ - for centre speaker.
displayed, then press OK.
4 Press VOL +/- within 5 seconds to set the
delay time for audio output.
» ‘SURROUND DELAY’ - for surround
•
To return to previous step, press
BACK.
speakers.
•
To exit the setup, press AUDIO
SETUP.
» ‘BACK DELAY’ - for back (rear)
speakers.
4 Press
or adjust the volume control to
increase or decrease the delay time, then
press OK.
Tip
• If the volume control is not adjusted within 10
seconds, it resumes normal volume control
function.
•
The last volume setting will be
stored automatically after 5 seconds
of inactivity.
5 Repeat steps 3 - 4 for other speaker
settings.
•
To return to previous step, press
BACK.
•
To exit the setup, press AUDIO
SETUP.
Note
• This setting is only applicable to centre, back
and surround speakers.
• Set a longer delay time if the centre, back or
surround speakers are closer to the listening
position than the front speakers.
• Rear and centre delays range from 0 to 15 MS.
The default setting is 0 MS.
16 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
3 Press
to change the settings, then
press OK.
Use Philips EasyLink
•
To exit the setup, press AUDIO
SETUP.
Your product supports Philips EasyLink, which
uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices
that are connected through HDMI connectors
can be controlled by a single remote control.
Note
• You must turn on the HDMI CEC operations
on the TV/devices before you can enjoy the
EasyLink controls. See the TV/devices manual
for details.
Note
• Dual sound may hear from TV and this Digital
Receiver if the ‘TV AUDIO INPUT’ mapping is
not done properly.
• Philips does not guarantee 100%
interoperability with all HDMI CEC devices.
1 Press AUDIO SETUP.
2 Press
/
repeatedly to select one of
the Philips EasyLink features: ‘EASYLINK’
> ‘ONE-TOUCH STANDBY’ > ‘SYSTEM
AUDIO CONTROL’ > ‘TV AUDIO
INPUT’, then press OK.
EasyLink
Turns all EasyLink features off or on (see below).
One-touch standby
When you press and hold STANDBY for
three seconds, all the connected HDMI CEC
devices switch to standby simultaneously. You
can also perform one-touch standby using
the remote control for any of the connected
HDMI devices.
To disable this feature, select ‘OFF’.
System audio control
When you play from the connected HDMI
CEC device, this Digital Receiver switches
automatically to the corresponding audio
source. You can use the remote control for
any of the connected HDMI devices to adjust
the volume.
To use this feature, select ‘ON’. Then
proceed to ‘TV AUDIO INPUT’ to map the
audio input of this Digital Receiver to the TV.
TV audio input
Selects the audio socket used to connect this
Digital Receiver to the TV. When you select
the audio input correctly, this Digital Receiver
switches automatically to the audio input
from the device that is playing.
EN 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Select a play source
On the main unit
1 Press the SOURCE button repeatedly to
select: COAX IN > OPTI IN > AUX1 >
AUX2 > MP3 LINK > FM > HDMI IN1 >
HDMI IN2.
On the remote control
•
Press AUDIO SOURCE repeatedly
to listen to the audio output from the
connected device.
Display
Device connected to
AUX1
AUDIO IN-AUX1
sockets.
AUX2
AUDIO IN-AUX2
sockets.
COAX IN
OPTI IN
MP3 LINK
DIGITAL IN-
COAXIAL socket.
DIGITAL IN-
OPTICAL socket.
MP3 LINK socket.
•
Press HDMI SOURCE to select the
device that is connected to the HDMI
IN1 or HDMI IN2 socket.
•
Press RADIO to switch to FM band.
18 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
5 Play
Play from radio
Check that the FM antenna has been connected
to the Digital Receiver. If not, connect the
supplied FM antenna to the FM75 socket
and fix its ends to the wall.
Play from portable media
player
Simply connect your portable media player
(e.g. MP3 player) to the Digital Receiver to
enjoy superb sound quality from your music
collection.
FM
(75 Ω)
ANTENNA
MP3
Tip
• For better FM stereo reception, connect an
external FM antenna (not supplied).
• Position the antenna as far away as possible
from your TV, VCR or other radiation source
to prevent interference.
1 Connect a 3.5 mm stereo audio cable
(not supplied) from the MP3 LINK
socket on the Digital Receiver to the
‘headphone’ socket on the portable
media player.
First time tuning
2 Press AUDIO SOURCE repeatedly until
When you access radio mode for the first
time, follow the instructions to install the radio
stations.
‘MP3 LINK’ is displayed.
3 Start play on your portable media player.
•
To stop play, press STOP on the
1 Press RADIO.
portable media player.
» ‘AUTO INSTALL ... PRESS OK’ is
displayed.
Note
2 Press OK.
• Control playback is only possible on the
portable media player.
• Stop play on the portable media player before
you switch to other play media/source.
» All detected radio stations are stored.
» Once complete, it tunes to the first
preset radio station.
•
To stop auto tuning, press BACK.
Note
• This Digital Receiver can store up to a
maximum of 40 radio stations.
• If auto installation is not activated or less
than 5 radio stations are stored, you will be
prompted to install the radio stations again.
EN 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Listen to radio
Search and store radio stations
individually
1 Press RADIO.
1 Press RADIO.
2 Use the remote control to control the
radio.
2 Press
.
» It starts searching until a radio station
Button
Action
is detected.
/
Selects a preset radio station.
Tunes the radio frequency up or
down.
» To fine-tune the radio frequency, press
.
3 Press PROGRAM.
DELETE Press and hold to delete the
current radio station from the
preset list.
» The preset station number blinks.
» If no action is carried out within 20
seconds after the above step, it exits
the preset mode.
The preset number for other
radio stations remain unchanged.
4 Press
/
(or the Numeric buttons)
Note
to select a preset number to store.
• If the FM radio station transmits RDS (Radio
Data System) data, the name of the radio
station is displayed.
5 Press PROGRAM to confirm.
Use sleep timer to power off
Reinstall all the radio stations
Use the sleep timer feature to switch this
Digital Receiver to standby automatically after
the preset time.
1 Press RADIO.
2 Press and hold PROGRAM for more than
5 seconds.
1 Press SLEEP repeatedly to select the
countdown time before power off.
» ‘60 > 45 > 30 > 15 > OFF’ is
displayed.
» All previously stored radio stations are
replaced.
Note
•
To cancel the sleep timer, select
‘OFF’.
If the timer has been set, press
SLEEP to view the time left or press
repeatedly to set a new power off
time.
• Check the radio antenna connection if no
stereo signal is detected or less than 5 stations
are detected during radio installation.
•
20 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Adjust sound
Select double bass
Control the volume
1 Press VOL +/- to increase or decrease
1 Press DOUBLE BASS to turn the double
the volume.
bass mode on or off.
•
•
To mute, press
To restore the volume, press again
.
Note
or press VOL +.
• Double Bass is used to increase the resonance
of the bass effect, not the bass power level. It
is designed to enhance movies sound effect.
Select surround sound
1 Press SURROUND repeatedly to select
the best surround output available on the
disc or the surround output best suited
to the music that you play.
Option
Description
MULTI-
Multi-channel surround
CHANNEL
output: DTS (Digital Theater
7.1 / MULTI- System), Dolby Digital and
CHANNEL
5.1
Dolby Pro Logic II/IIx.
SURROUND
5CHANNEL / Enhances the stereo channel
7CHANNEL output by duplicating the
STEREO
STEREO
sound output to the centre
and rear speakers. Ideal for
party music.
Stereo sound.
EN 21
Download from Www.Somanuals.com. All Manuals Search And Download.
Select a preset sound effect
1 Press SOUND repeatedly to select the
most suitable sound effect for the video
or music that you are playing.
Movie / Music Description
CONCERT / Flat and pure sound mode.
CLASSIC
Ideal for listening to classical
music and watching live
concert discs.
DRAMA /
JAZZ
Moderate sound mode
suitable for lounge music and
watching dramas.
ACTION
/ROCK
Enhanced low and high range
for great sounding movie
effects and atmosphere. Great
for action movies and rock/
pop music.
SPORTS
NIGHT
Note
Moderate mid-range and
surround effects for clear
vocals and the atmosphere of
a live sports venue. Also ideal
for video gaming.
Dynamically controlled sound
mode suitable for watching
movies at night or for non-
intrusive background music.
• For stereo mode with compressed data (e.g.
MP3), it is automatically set to the full sound
mode. Therefore, no differences with the
sound effect when you select different sound
mode.
22 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Speakers
7 Specifications
•
•
System: full range satellite
Speaker impedance: 4 ohm (centre), 8
ohm (Front/Back/Surround)
•
•
•
Speaker drivers: 3” full range.
Frequency response: 150 Hz-20 kHz
Dimensions (WxHxD):
Note
• Specification and design are subject to change
without notice
•
•
Centre: 244 x 103 x 74 (mm)
Front/Back/Surround: 103 x 203 x
71 (mm)
Amplifier
•
•
•
Total output power: 1000 W RMS
Frequency response: 40 Hz-20 kHz
Signal-to-noise ratio: > 60 dB (A-
weighted)
•
Weight
•
•
•
Centre: 0.79 kg
Front: 0.54 kg
Back/Surround: 0.44 kg
•
Input sensitivity
•
•
AUX 1 & 2: 400 mV
MP3 LINK: 250 mV
Subwoofer
•
•
•
•
Impedance: 4 ohm
Speaker drivers: 165 mm (6.5”) woofer
Frequency response: 40 Hz-150 Hz
Dimensions (WxHxD): 163 x 363 x 369
(mm)
Radio
•
•
•
•
•
Tuning range: FM 87.5-108 MHz
26 dB quieting sensitivity: FM 22 dBf
Signal-to-noise ratio: FM 55 dB
Harmonic distortion: FM 3%
Frequency response: FM 180 Hz-10 kHz
/ ±6 dB
•
Weight: 4.7 kg
•
Stereo Threshold: FM 29 dB
Main unit
•
•
•
Power supply: 220-240 V; ~50 Hz
Power consumption: 120 W
Dimensions (WxHxD): 435 x 57 x 365
(mm)
•
Weight: 3.36 kg
EN 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Sound
8 Troubleshooting
No sound.
•
Ensure that the audio or HDMI cables are
connected and press AUDIO SOURCE
or HDMI SOURCE to select the correct
input source.
Warning
• Risk of electric shock. Never remove the
casing of the product.
Poor radio reception.
To keep the warranty valid, never try to repair
the product yourself.
•
If the signal is too weak, adjust the
antenna or connect an external antenna
for better reception.
If you encounter problems when using the
product, check the following points before
requesting service. If the problem remains
unsolved, register your product and get support
•
Place the antenna further away from any
equipment that may cause interference.
No output from the Set-Top Box.
•
Not all the Set-Top-Box supports output
through HDMI receiver. Check with the
respective manufacturer for the HDMI
output support.
If you contact Philips, you will be asked for
the model and serial number of your Digital
Receiver.The model number and serial number
are on the back or underside of your Digital
Receiver.Write the numbers here:
Dual sound is heard from TV and this Digital
Receiver.
Model No. __________________________
Serial No. ___________________________
•
Check if you have done the ‘TV AUDIO
INPUT’ mapping correctly, see ‘Getting
Started’ > ‘Use Philips EasyLink’.
•
Turn off the ‘EASYLINK’ feature, see
‘Getting Started’ > ‘Use Philips EasyLink’.
Main unit
No reaction to the remote control.
•
Disconnect this product from the socket
for a few minutes, then connect again.
Point the remote control at the product.
Insert the batteries correctly.
•
•
•
Insert new batteries if necessary.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
9 Glossary
H
HDMI
High-Definition Multimedia Interface is a
high-speed digital interface that can transmit
uncompressed high definition video and
digital multichannel audio. It delivers high
quality picture and sound quality, completely
free from noise. HDMI is fully backward-
compatible with DVI.
As required by the HDMI standard,
connecting to HDMI or DVI products without
HDCP (High-bandwidth Digital Content
Protection) will result in no Video or Audio
output.
A
Analogue audio
An electrical signal that directly represents
sound. Same as digital audio, which may
be an electrical signal, but is an indirect
representation of sound. Analogue sound
varies, while digital sound has specific
numerical values.
D
Dolby Digital
A surround sound system developed by Dolby
Laboratories that contains up to six channels
of digital audio (front left and right, surround
left and right, centre and subwoofer.)
M
MP3
A file format with a sound data compression
system. MP3 is the abbreviation of Motion
Picture Experts Group 1 (or MPEG-1) Audio
Layer 3. With the MP3 format, one CD-R or
CD-RW can contain about 10 times more
data than a regular CD.
Dolby Digital Pro Logic II
An advanced, matrix decoding technology that
expands any two channel audio, such as CDs
and stereo encoded videocassettes, video
games and TV broadcasts to a five channel
full bandwidth (range) playback (Left/Centre/
Right/Left Surround/Right Surround), resulting
in a surround sound experience.
Multichannel
Usually DVD is specified to have each sound
track constitute one sound field. Multichannel
refers to a structure of sound tracks having
three or more channels.
DTS
Digital Theatre Systems. A surround sound
system for providing 5.1 and 7.1 channels of
discrete digital audio in consumer electronics
products and software content. It is not
developed by Dolby Digital.
S
Stereo
Literally means solid. Usually taken to refer to
two channel stereo, though developments in
digital audio facilitate multichannel stereo.
Surround
A system that creates realistic, three-
dimensional sound fields. It is usually achieved
with multiple speakers that are arranged
around the listener.
EN 25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
|