1
5
2
3
4
6
7
8
9
10
14
18
11
15
19
12
16
13
17
21
20
2
1
Download from Www.Somanuals.com. All Manuals Search And Download.
3
ENGLISH
HQC333 HQC222
4203 000 54361
◗ Hair length settings
The hair length settings are indicated in millimetres on the arms of the
comb attachment. The settings correspond to the remaining hair length
after cutting.
3 Start at the setting for maximum hair length (41 mm for HQC333 /
21 mm for HQC222).
Small comb HQC333/HQC222
Large comb HQC333
hair length
23 mm
hair length
3 mm
6 mm
26 mm
9 mm
29 mm
12 mm
15 mm
18 mm
21 mm
32 mm
35 mm
38 mm
41 mm
4 Make sure that the flat part of the comb attachment is always fully in
contact with the scalp to obtain an even cutting result (fig. 6).
5 Pass the clipper slowly over the crown from different directions to
achieve an even cutting result.
6 Make overlapping passes over the head to ensure that the clipper
catches all the hairs that need to be cut.
7 Comb the hair in the direction of hair growth from time to time so
that the clipper can catch the hair more easily.
8 To achieve a good result with curly, sparse or long hair, you can use
a comb to guide the hair towards the clipper.
B
We advise you to regularly remove clipped hair from the comb while clipping.
Graduation
The Philishave hair clipper not only allows you to cut the hair evenly at the
same length all over the head, it also enables you to achieve a smooth
transition from longer hair on top of the head to shorter hair on the back
and sides of the head.
1 Start clipping at the setting for maximum hair length (i.e. position
41 mm for HQC333 / 21 mm for HQC222).
2 Then choose a shorter setting and cut the hair on all parts of the
head except the top, where you want the hair to be longer.
3 You can repeat this procedure until the hair on every part of the
head has the desired length.
Precise contouring without comb attachment
You can use the clipper without comb attachment to contour the neckline
and the area around the ears.
Be careful when you are clipping without comb attachment, for the clipper
will remove every hair it touches.
1 Remove the comb attachment by pulling it off the clipper.
2 Before contouring the hairline round the ears, comb the hair ends
over the ear.
3 Bend the person's ear to get it out of the way.
4 Tilt the clipper in such a way that only one edge of the cutting
element touches the hair ends (fig. 8).
5 Only cut the hair ends. The hairline should be close to the ear (fig. 9).
6 To contour the nape hairline and the sideburns, turn the clipper and
make downward strokes (fig. 10).
7 Move slowly and smoothly.
8 Just follow the natural hairline (fig. 11).
Cutting over styling comb or fingers
This technique can be used to obtain hair lengths over 41 mm ( HQC333)
and 21 mm (HQC222). Bear in mind that this technique is difficult to
master and should only be applied by experienced users.
1 Make sure the comb attachment is not attached to the appliance.
2 Comb a small section of hair upwards. Lift the hair with a styling
Download from Www.Somanuals.com. All Manuals Search And Download.
4
ENGLISH
HQC333 HQC222
4203 000 54361
comb or hold it between your fingers until only the length that needs
to be cut sticks out (fig. 12).
3 Cut the hair protruding from the comb or fingers (fig. 13).
4 Continue this procedure and comb frequently to remove cut hair and
to check for unevenly cut sections.
.
Cleaning
Clean the appliance every time you have used it.
Do not use abrasives, scourers or liquids such as alcohol, petrol or acetone
to clean the appliance.
1 Make sure the appliance is switched off and unplugged.
2 Make sure the comb attachment is not attached to the appliance
(fig. 14).
Never pull at the flexible top of the comb attachment. Always pull at the
bottom part.
3 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (fig. 15).
Be careful that the cutting unit does not fall to the floor.
4 Clean the cutting unit and the inside of the appliance with the brush
supplied (fig. 16).
5 Place the lug of the cutting unit into the slot and push the unit back
onto the appliance ('click') (fig. 17).
.
Storage
◗ You can store the appliance in the pouch supplied.
.
Replacement
A worn or damaged cutting unit should only be replaced with an original
Philips cutting unit.
1 Push the middle part of the cutting unit upwards with your thumb
until it opens and then pull it off the appliance (fig. 15).
2 Place the lug of the cutting unit into the slot and push the cutting unit
back ('click') (fig. 17).
.
Environment (HQC333 only)
The built-in rechargeable battery contains substances that may pollute the
environment.
Disposal of the battery
Remove the battery when you discard the appliance. Do not throw the
battery away with the normal household waste, but hand it in at an official
collection point. You can also take the appliance to a Philips service centre,
which will remove the battery for you and will dispose of it in an
environmentally safe way.
Only remove the battery if it is completely empty.
1 Disconnect the appliance from the mains and let the appliance run
until the motor stops.
2 Open and remove the cutting unit (fig. 15).
3 Remove the metal clip by means of a screwdriver (fig. 18).
4 Open the housing (fig. 19).
Insert a screwdriver into one of the grooves next to the socket for the
appliance plug. Turn the screwdriver to separate the two housing halves.
5 Insert a screwdriver into the small slot in the printed circuit board
marked with an arrow. Push the screwdriver down until part of the
printed circuit board breaks off (fig. 20).
6 Lift the battery out and cut the wires to separate the battery from
the power unit (fig. 21).
Do not connect the appliance to the mains again after it has been opened!
.
Guarantee & service
If you need information or if you have a problem, please visit the Philips
in your country (you will find its phone number in the worldwide guarantee
leaflet). If there is no Customer Care Centre in your country, turn to your
local Philips dealer or contact the Service Department of Philips Domestic
Appliances and Personal Care BV.
Download from Www.Somanuals.com. All Manuals Search And Download.
|