Hospitality Television
20/26/32HF5335D
15/20HF5234
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Analogue Programs
Ensure the TV is in Analogue mode. If it is in Digital mode, press the A/D (Analogue/Digital) key on the
Remote Control to enter the Analogue mode.
1. Press the
(Menu TV) key on the Remote Control
2. Press the Up/Down Arrow Key to scroll to the item called INSTALL and press OK
3. Press the Up/Down Arrow Key to scroll to the item AUTO STORE and press OK
The TV will now start to scan and install all available (Analogue) TV channels automatically. This operation will
take a few minutes. The TV display will show the progress of the scan and the number of programmes found.
Refer to the chapter on Automatic Tuning of Analogue Programmes in the User Manual for more details. You
can also refer to the chapter on Manual Tuning of Analogue Programmes in the User Manual if a manual scan is
preferred.
4.
Activating the Hotel Mode Setup menu (BDS)
1. Switch on the television and select an analogue channel
2. On the Remote Control, press keys: [3, 1, 9, 7, 5, 3, MUTE]
3. The BDS HOTEL MODE SETUP MENU becomes visible
4. Use the cursor keys to select and change any of the following settings:
Function
Possible selections
BDS MODE
ON /OFF
SWITCH ON SETTINGS
SWITCH ON VOLUME
MAXIMUM VOLUME
SWITCH ON CHANNEL
POWER ON
DISPLAY MESSAGE
WELCOME MESSAGE
CONTROL SETTINGS
LOCAL KEYBOARD LOCK
REMOTE CONTROL LOCK
OSD DISPLAY
HIGH SECURITY MODE
AUTO SCART
MONITOR OUT
BLANK CHANNEL
STORE
0-100, LAST STATUS
0-100
USER DEFINED, LAST STATUS
ON/STANDBY/LAST STATUS
ON/OFF
LINE 1/LINE 2/CLEAR
ON/OFF/ALL
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
>
5. Select “STORE” and press [CURSOR RIGHT] to save the settings and exit BDS Hotel Mode
setup. Press [MENU] to exit without saving.
6. For BDS Hotel Mode settings to take effect, you must turn the TV set Off, then back On.
BDS Hotel Mode Functions
This paragraph describes the functionality of each item in the BDS Hotel Mode Setup menu.
BDS MODE
ON
BDS Hotel Mode is ON:
ꢀ
The user menu is blocked.
ꢀ
All settings of the Hotel Mode Setup menu are in effect.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
OFF
BDS Hotel Mode is OFF:
The TV operates as a normal consumer TV
ꢀ
SWITCH ON VOL
When the user switches the TV ON, it will play at the specified volume level. There are 2 options:
ꢀ
LAST STATUS Upon start-up, the TV volume will be set to the level before the TV set was
last turned off.
USER DEFINED As specified by installer
ꢀ
Remark: “SWITCH ON VOL” cannot exceed the MAXIMUM VOL level. This is the volume level with which
the Hotel Mode Setup menu was entered.
MAXIMUM VOL
The TV Volume will not exceed the selected volume level.
SWITCH ON CHANNEL
When the user switches the TV ON, it will tune to the specified channel. There are 2 options:
ꢀ
ꢀ
LAST STATUS The TV will switch on to the last channel that was shown before the TV set
was turned off
USER DEFINED Any analogue channel can be chosen to be the first channel to switch on
POWER ON
The Power On function allows the TV to enter a specific mode of operation (On or Standby) after the mains
power is activated.
ON
STANDBY
When set, the TV will always turn ON after the mains power is enabled.
When set, the TV will always turn to STANDBY after mains power is enabled
LAST STATUS When set, the TV will always turn to the last power status before the mains power was
disabled.
DISPLAY MESSAGE
ON
OFF
Enables display of the Welcome Message for 30 seconds after the TV set is turned on
Disables the display of the Welcome Message.
If OSD DISPLAY is set to OFF, then the Welcome Message is automatically disabled.
WELCOME MESSAGE
The Welcome Message function allows the TV to show a customized greeting to the hotel guest whenever the
TV is switched on. This helps to personalize the hotel experience for guests.
The Welcome Message can consist of 2 lines of text, with each line containing a maximum of 20 alphanumeric
characters. Use the Remote Control arrow keys to create the Welcome Message.
To enable the display of the Welcome Message, the DISPLAY MESSAGE option must be ON
To clear the Welcome Message from the TV’s memory, select CLEAR
LOCAL KEYBOARD LOCK
ON
OFF
ALL
The television keys VOLUME +/-, PROGRAM +/- and MENU are blocked.
The television keys VOLUME +/-, PROGRAM +/- and MENU function normally
The television keys VOLUME +/-, PROGRAM +/-, MENU and POWER are blocked.
REMOTE CONTROL LOCK
ON
OFF
Standard Remote Control keys are disabled.
All Remote Control keys will function normally.
OSD DISPLAY
ON
OFF
Normal screen information is displayed (e.g. programme information)
Screen information is suppressed.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGH SECURITY MODE
ON
Allows access to the BDS Hotel Mode Setup Menu via the special BDS Setup Remote only.
(RC2573/01)
OFF
Allows access to the BDS Hotel Mode Setup Menu via BDS Setup Remote or via normal Remote
Control (using special key code sequence).
AUTO SCART
The Auto Scart function enables auto-detection of AV devices that are connected to the TV’s Scart connector.
ON
OFF
Enables Auto Scart switching in BDS Hotel Mode.
Disables Auto Scart switching in BDS Hotel Mode.
MONITOR OUT
ON
OFF
Allows audio & video output from TV via relevant AV connectors (if available).
Disables both Audio & Video output from the TV (to prevent illegal copying).
BLANK CHANNEL
The Blank Channel function disables the display of video on the TV, but does not affect the audio output. This
function can be used for audio applications (example: Off-air radio transmission, music channels, and so on),
which do not necessarily require the display of video.
ON
The current programme is blanked
OFF The current programme is not blanked (normal visible; DEFAULT value)
BLANK CHANNEL can be set for every channel. Use [P+ / P-] to go through all the programmes and set the
desired status per channel. The programme number is visible in the top left corner.
Low Battery Check
This television set has a special feature which checks the battery power level of a TV Remote Control, and
indicates if the battery is low and requires changing.
(Note: The Low Battery Check function works only with certain models of Remote Controls. Please check
with the Philips sales representative if the Remote Control used with this TV supports this function)
To activate the Low Battery Check function, hold the TV Remote Control in front of the TV, and press and
hold the OK button on the Remote Control for at least 5 seconds. A message will appear on the TV screen to
indicate if the battery power level is OK, or if it is Low. If the message indicates that the battery level is low, it
is recommended to change the batteries of the Remote Control immediately.
5.
Cloning of settings
Cloning of analogue TV channels and TV settings as described in the chapter
Hotel Mode Set-up menu
For 15/20HF5234
o
o
Wireless cloning with the SmartLoader 22AV1120 or 22AV1135
Cloning off all adjustable TV settings + analogue channel table
For 20/26/32HF5335D
o
o
Wired cloning with the SmartLoader 22AV1135 using the wire packed with the SmartLoader
Cloning off all adjustable TV settings + analogue channel table (digital channel table via automatic
installation)
Instruction for cloning of settings between TVs
Philips SmartLoader (22AV1135/00)
The Philips SmartLoader is an installation tool especially designed for easy and fast installation and copying of
TV settings on Philips Institutional TV’s.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
The Philips SmartLoader works in 2 modes – Wireless and Wired:
Wireless mode ---- through infrared sensor (15/20HF5234)
Switch the SmartLoader to “Wireless” mode by sliding the side-switch to the
icon on the SmartLoader
device. Point the Wireless SmartLoader to the TV’s infrared receiver (optimal distance of 5-30cm) and proceed
with the Installation procedure listed below.
Wired mode ---- using the by-packed accessory cable(s) (20/26/32HF5335D)
Switch the SmartLoader to “Wired” mode by sliding the side-switch to the
device.
icon on the SmartLoader
Examine the rear connectors of the TV set to determine if the 3-pin or 4-pin female connector wire (packed
with the Wireless SmartLoader) should be used. Plug in the correct connector wire to the corresponding
opening on the TV set (usually marked as SERV C), and then connect the RJ11 jack end of the accessory wire
to the RJ11 socket on the SmartLoader.
The Installation Procedure consists of three simple steps:
1. Choosing a Master TV
The Master TV is the TV set whose installation and configuration settings are to be copied into other TV’s (of
the same type only).
2. Programming the SmartLoader with the settings from the Master TV
Follow these steps to program the SmartLoader with the settings of the Master TV.
a) Wireless method
ꢁSet the SmartLoader to “Wireless” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
b) Wired method
ꢁConnect the SmartLoader to the TV using the appropriate accessory cable.
ꢁSet the SmartLoader to “Wired” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
The Master TV will show the following menu:
SMARTLOADER TO TV >
TV TO SMARTLOADER >
On the TV screen, highlight the menu option “TV TO SMARTLOADER”
Press the right arrow key on the SmartLoader to start the programming process
A number display (from 0~100) will be shown on screen, indicating the percentage of the programming
progress from the TV to the SmartLoader. When the programming is completed, “##” will show “100” and the
message “DONE” will appear.
TV TO SMARTLOADER ## (0-100)
The SmartLoader is programmed and can be used to install and configure other TVs.
Copying the settings of the Master TV to other TVs with the SmartLoader
Follow these steps to install and configure the settings of a Philips TV with the SmartLoader.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
a) Wireless method
ꢁSet the SmartLoader to “Wireless” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
b) Wired method
ꢁConnect the SmartLoader to the TV using the appropriate accessory cable.
ꢁSet the SmartLoader to “Wired” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
On the TV screen, highlight the menu option “SMARTLOADER TO TV”
Press the right arrow key on the SmartLoader to initiate the copying process
> A number display (from 0~100) will be shown on screen, indicating the percentage of the installation
progress from the SmartLoader to the TV. When the data transfer is completed, “##” will show “100” and
the message GOODBYE will appear.
SMARTLOADER TO TV ## (0-100)
>
The TV will go to Standby mode. When the TV is next powered on, it will be configured with the settings
from the Master TV, and ready for use.
Problems and Solutions:
1. The message “I2C ERROR” is displayed on the screen.
ꢁBad connection of RJ11 wire or wrong data transmission has occurred. Try again.
2. The message “WRONG VERSION” is displayed on the screen.
ꢁThe program contained in the SmartLoader has a software code incompatible with the actual TV.
Reprogram the Wireless SmartLoader from a Master TV whose software code is compatible with the
actual TV.
3. TV doesn’t respond to the SmartLoader.
ꢁCheck if the LED on the SmartLoader lights up in green when pressing any button.
If the LED is red, it means that the batteries are low and should be replaced.
ꢁBring the SmartLoader closer to the TV infrared receiver and try again.
Notes:
ꢀ Make sure that the 3 R6/AA sized batteries are placed correctly in the bottom compartment of the
SmartLoader. The LED on the SmartLoader should light up in green when pressing any button, indicating
operational batteries. When the LED shows red, the batteries need to be replaced.
ꢀ The SmartLoader can only copy the settings between 2 TVs of the same type. Once the
SmartLoader is programmed with the settings from a Master TV of a certain type or model,
then these settings can be installed on another TV of the same model only.
ꢀ The SmartLoader cannot be used to copy the (digital) channel table of a Digital TV set.
ꢀ If the SmartLoader is used with a DVB (European Digital) TV set, then the TV set must first
be switched to Analog mode.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal of your old product.
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused. When this crossed-out wheeled bin
symbol is attached to a product it means the product is covered by the European
Directive 22002/96/EC. Please find out more about the separate collection system for
electrical and electronic products in your local neighborhood.
Please act according to your local rules and do not dispose of your old products with
your normal household waste. The correct disposal of your old product will help
prevent potential negative consequences for the environment and human health.
The packaging of this product is intended to be recycled. Apply to the
local authorities for correct disposal.
2007© Koninklijke Philips Electronics N.V. all rights reserved
Specifications are subject to change without notice
Trademarks are property of Koninklijke Philips Electronics N.V. or their respective owners.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
EN USER MANUAL
Download from Www.Somanuals.com. All Manuals Search And Download.
Model
Serial
Country
Austria
Belgium
Chech Rep
Denmark
Finland
Number
Tariff
0820 901114
070 222 303
800142840
€0.20/min
€0.17/min
free
local
local
€0.23/min
€0.12/min
free
free
local
€0.25/min
local
€0.20/min
local
local
local
free
€0.15/min
local
local
£0.15/min
3525 8759
09 2311 3415
08 9165 0005
0180 5 356 767
0 0800 3122 1280
0680018189
01 601 1777
199 404 041
40 6661 5644
0900 8407
France
Germany
Greece
Hungary
Ireland
Italy
Luxemburg
Netherlands
Norway
Poland
Portugal
Slovakia
Spain
Sweden
Switzerland
UK
2270 8111
0223491504
2 1359 1442
0800004537
902 888 784
08 5792 9100
0844 800 544
0906 1010 016
Download from Www.Somanuals.com. All Manuals Search And Download.
Product information
Recycling
• The Model and Serial number can be
found at the rear and the left hand
underside of your television set and
on the packaging.
The packaging of this product is intended to
be recycled. Apply to the local authorities for
correct disposal.
Disposal of your old product
Rear
of
TV
Left hand
Your product is designed and manufactured
with highly quality material and components,
which can be recycled and reused. When this
crossed-out wheeled bin symbol is attached
to a product, it means the product is covered
by the European Directive 2002/96/EC.
underside
of TV
• Standby Power Consumption for this set
is less than 1 W.
• Power Consumption of the set can found
on the type plate at the rear of the TV.
• For more specifications of the product
com/support.
Please inform yourself about the local
separate collection system for electrical and
electronic products. Please act according to
your local rules and do not dispose your old
products with your normal household waste.
The correct disposal of your old product will
help prevent potential negative consequences
for the environment and human health.
Note
Specifications and information are
subject to change without notice.
• If you need further assistance, please call
the customer support service in your
country. The corresponding telephone
numbers and addresses are given in the
supplied Worldwide guarantee booklet.
Disposal of batteries
The batteries supplied do not contain the
heavy metals mercury and cadmium. Please
check on how to dispose exhausted
batteries according to local regulations.
Important
• AC3 (an audio format) is not supported
for this set. Use the
key on the
remote control to select an alternative
audio.
• Some TV antennas require power from
the TV set. This set does not support such
a feature.
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of contents
1
Introduction...............................3
9
Services lists
1.1 Important Information....................... 3
1.1.1 Stationary images on the TV screen
.................................................................3
1.1.2 Electric, Magnectic and
9.1 Rearrange services..............................15
9.2 View new TV channels or Listen
to new Radio stations........................ 15
electromagnectic Fields (“EMF”)..... 3
1.2 What is digital TV?..............................4
1.3 Digital or Analogue channels?.......... 4
10
Service setup............................. 16
10.1 Add new services................................ 16
10.2 Reinstall all services............................ 16
10.3 Manual install services........................17
2
Safety..........................................5
2.1 General..................................................5
2.2 Care of the screen..............................5
11
Test reception...........................18
12
13
14
15
16
Preferences................................19
Access restrictions.....................20
Setting up your favourite list....21
Information................................22
Using the Options menu...........23
3
Overview of the television keys
and connectors..........................6
3.1 Side controls. ...................................... 6
3.2 Rear connectors..................................6
3.3 Side connectors.................................. 6
4
Getting started..........................7
4.1 Before you start...................................7
4.2 Connect the antenna..........................7
4.3 Connect the mains..............................7
4.4 Switching on the TV............................7
4.5 Using the remote control. ................7
17
18
19
TV Guide (Electronic ...............24
Recording function....................25
Digital teletext (MHEG)...........27
20
21
22
Using the Conditional Access
Module (CAM ............................28
5
6
Remote control functions.........8
Overview of Digital main menu
and sub-menus...........................10
Automatic tuning of analogue
programmes.............................. 29
7
8
Switching on the TV for the
first time.................................... 13
Manual tuning of analogue
programmes.............................. 30
23
24
25
Programme sort........................31
Naming of channel.....................32
Understanding the information
on the banner............................ 14
8.1 Banner description..............................14
8.2 Symbols description............................14
Selecting your favourite
programme ...............................33
1
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Features
26.1 Timer......................................................34
26.2 Parental control...................................35
26.3 Child lock..............................................36
26.4 Active control...................................... 36
27
28
29
30
31
Picture and Sound setings........37
Smart Picture and Sound.........38
Screen formats..........................39
Teletext......................................40
Using the TV as PC monitor
31.1 Connecting the PC..............................42
31.2 Control TV settings while a PC is
connected ............................................ 42
32
Using the TV in HD (High
Definition) mode
32.1 Connecting the HD equipment........43
32.2 Control TV settings while in HD
mode...................................................... 43
33
Connecting other equipment
33.1 Overview of connections...................45
33.2 Connect VCR and DVD recorder...46
33.3 Connect Decoder and VCR..............46
33.4 Connect 2 VCRs or VCR and DVD....
recorder.................................................47
33.5 Connect a satellite receiver..............47
33.6 Connect a DVD player, Cable box or
Game console...................................... 48
33.7 Connect a DVD player, a Satellite
receiver or Cable box .......................48
33.8 Connect a PC.......................................49
33.9 Connect a Camera, Camcorder or
Game console...................................... 50
33.9.1 Connect a Headphone.......................50
34
35
Troubleshooting........................51
Glossary..................................... 53
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1 Introduction
•
•
Stock market stickers: presented at the
bottom of the TV screen;
Shopping channel logos and pricing
displays: bright and shown constantly or
repeatedly in the same location on the
TV screen.
Thank you for purchasing this television set.
This manual contains all information you
will need to initially install and operate your
new TV.
If this instruction manual does not
give an answer to your problem or
•
Examples of still pictures also include
logos, computer images, time display,
teletext and images displayed in 4:3
mode, static images or characters, etc.
if Troubleshooting page does not solve
your TV problem, you can call your Local
Philips Customer or Service Centre. See the
supplied Worldwide guarantee booklet for
details. Please have the Model and Product
number (which you can find at the back or
the bottom of your television set or on the
packaging) ready, before calling the Philips
customer support service.
Tip:
Reduce contrast and brightness when
viewing.
1.1.2 Electric, Magnetic and
Electromagnetic Fields (“EMF”)
• Philips Royal manufactures and sells many
products targeted at consumers, which,
like any electronic apparatus, in general
have the ability to emit and receive
electro magnetic signals.
1.1
Important information
1.1.1 Stationary images on the TV
screen
A characteristic of LCD and Plasma Panels
is that displaying the same image for a long
time can cause a permanent after-image to
remain on the screen. This is called
phosphor burn in. Normal use of the TV
should involve the showing of pictures
that contain constantly moving and changing
images that fill the screen.
• One of Philips’ leading Business
Principles is to take all necessary health
and safety measures for our products, to
comply with all applicable legal
requirements and to stay well within the
EMF standards applicable at the time of
producing the products.
• Philips is committed to develop, produce
and market products that cause no
adverse health effects.
Examples of stationary images (this is not
an all inclusive list, you may encounter
others in your viewing).
• Philips confirms that if its products are
handled properly for their intended use,
they are safe to use according to scientific
evidence available today.
•
•
TV and DVD menus: listings of DVD
disk content.
Black bars: when black bars appear at
the left and right side of the screen, it is
recommended to change to a picture
format so that the picture fills the entire
screen;
TV channel logo: present a problem if
they are bright and stationary. Moving
or low-contrast graphics are less likely
to cause uneven aging of the screen;
• Philips plays an active role in the
development of international EMF and
safety standards, enabling Philips to
anticipate further developments in
standardisation for early integration in its
products.
•
3
Download from Www.Somanuals.com. All Manuals Search And Download.
1.2 What is digital TV?
Note
Digital Television offers a far wider choice
of TV viewing, free from the interference
that you may experience on analogue
TV. It promises to transform television
viewing into a whole new experience.
There is a greater selection of widescreen
programming. Many of your favourite
programmes are in widescreen on the
digital channels - something the analogue TV
cannot do properly.
•
Chapters 6 to 20 contain all the
information you need to operate your
TV in the Digital mode. Chapters 21
to 30 contain all the information and
instructions you need to operate your
TV in the Analogue mode.
There is new whole experience of
interactivity on digital TV. By using your
remote control, you can access all kinds
of information like the digital text which
is much clearer than the old teletext
system. It gives you the added enjoyment
of related information running alongside
the programme you are watching. You
can also access an Electronic Programme
Guide that provides you with a quick and
easy way to view a complete list of digital
programmes as you would in a newspaper
or TV magazine.
1.3 Digital or Analogue channels?
When the television is powered on for the
first time, it will always be in Digital mode.
Use the
key of the remote control to
switch the TV between analogue and digital
mode. Use the P + / – or
to
keys to select channels.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Safety
7
8
Warning: The connections do not
Take care not to connect too many
equipment to the same mains socket
as it may cause overloading resulting
in fire or electric shock.
Avoid placing a vase or vases filled
with water on top or near the TV.
Water spilled into the set could result
in electric shock. Do not operate set if
water is spilled into the set. Unplug the
power cord from the mains immediately
and have the set checked by a qualified
serviceman.
have to be made before hanging but the
cables must be inserted into connectors
of the TV.
2.1 General
1
Place or hang the TV wherever you
want but make sure that air can
circulate freely through the ventilation
slots.
Do not install the TV in a confined
space such as a book case or a similar
unit.
To prevent any unsafe situations, no
naked flame sources such as lighted
candles should be placed in the vicinity
of the TV set.
Avoid heat, direct sunlight and exposure
to rain or water.
2
3
9
Installation of the TV set on thewall
should be carried out by a qualified
serviceman. Improper and incorrect
installation may render the set unsafe.
2.2 Care of the screen
4
1
Do not remove the protective sheet
until you have completed the stand/
wallmounting and connections. Please
handle with care.
X
X
Note
Use only the soft cloth provided
to clean the glossy front of the
TV.
5
6
As a safety precaution, do not touch any
part of the TV, power lead or aerial
lead during lightning storms.
Pull the power lead by the plug. Do not
pull on the power lead. Do not use a
poor fitting mains socket. Insert the plug
fully into the mains. If it is loose, it may
cause arching and result in fire.
X
2
Do not use too wet a cloth which is
dripping with water. Do not use
acetone, toluene or alcohol to clean
the TV. As a safety precaution, unplug
the power cord from the mains when
cleaning the set.
X
X
3 Do not touch, push or rub or strike the
screen with anything hard as this may
scratch, mar or damage the screen
permanently.
X
5
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Overview of television
keys and connectors
These connectors are located on the rear of the
TV and are backward facing..
3.1 Side controls
The Side controls are located on the left hand side
of the TV.
4
EXT 1
(RGB)
5
EXT 2
(CVBS /S-VIDEO)
2
1
CI (Common Interface) slot: to
connect a CAM (Conditional Access
Module) and a smartcard.
3
4
2
3
TV Aerial socket : Insert the aerial
plug into the 75 Ω : socket.
HDMI 1 / HDMI 2: to connect to
set-top box, DVD player/recorder, High
Definition equipment or Personal
Computer.
1
4
5
EXT4: to connect to equipment like
DVD, Decoder which have the same
sockets.
1
.
POWER
: to switch the TV on and
off. Note: For zero power
consumption, you need to remove the
mains cord from the mains socket.
VOLUME – / +: to change sound to
be louder or quieter.
6
EXT 1 (RGB) and
EXT 2 (CVBS/
S-VIDEO): connect to equipment like DVD
player/recorder, VCR, Decoder which
have similair connections (so called ‘scart
connetcions’).
2
3
MENU: to display or close menus.
The PROGRAM – / + keys can be used
to select a menu item and the VOLUME
– / + keys to enter into the selected
menu item and make adjustments.
PROGRAM – / +: to select
programmes.
3.3 Side connectors
These connectors are located on the side of the
TV.
4
1
3.2 Rear connectors
These connectors are located on the rear of the
TV and are downward facing.
2
EXT 3
1
2
Headphone
: for your personal
listening pleasure, connect the phono
jack to the headphone connector of the
TV.
Audio Video: for connecting to devices
like camera or camcorder.
1
2
3
4
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Getting started
4.1 Before you start
Warning
4.4 Switching on the TV
• To switch on the TV, press the
POWER key on the side of the set. A
blue indicator comes on and after a few
seconds, the screen lights up at the left
hand bottom of the front of the set.
The connections do not have to be
made before hanging but the cables
must be inserted into connectors of
the TV.
• If the TV set remains in standby mode
(red indicator), press the PROGRAM – /
key on the side controls or the P – / +
key on the remote control.
+
4.2 Connect the antenna
Insert the aerial plug firmly into the 75 Ω :
aerial socket at the bottom of the TV and in
the wall antenna socket.
Connectors at rear of TV
(facing downward)
Side controls
of TV
4.3 Connect the mains
Insert the mains cord (supplied) into the
mains socket at the backside (downward
facing) of the TV and in the wall socket.
4.5 Using the Remote Control
Warning
Insert the 2 batteries supplied. Be sure the
(+) and (-) ends of the batteries line up
correctly (inside of case is marked.)
Verify that the mains supply voltage in your
home corresponds to the voltage printed on
the sticker at the rear of the TV.
AC in
Plasma
LCD
TV
TV
To wall
socket
To wall
socket
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Remote control
functions
2
Sound mode
Used to force programmes in Stereo
and Nicam Stereo to Mono. For
bilingual programmes, select Dual å or
Dual » (as indicated on the screen
during such broadcasts). The Mono
indication shows up in red when in forced
position.
1
2
7
8
9
10
3
4
In digital mode, å-» displays the list
of audio languages.
5
6
3
Subtitles mode
In digital mode, this key activates or
deactivates the subtitle mode.
4
5
MENU
To call up or exit the TV analogue menus.
Cursors Up/Down/Left/Right
(
)
These 4 keys are used for selection and
adjustment of menu items.
6
Analogue or Digital mode
To switch between the television analogue
and digital mode.
7
8
Screen Format
(See page 39).
AV
To display Source List to select TV
(Analogue), Digital TV or connected
peripheral equipment (EXT 1, EXT 2,
EXT 3, EXT 4, HDMI 1 or HDMI 2). Use
the Î ï keys to select source and the
1
Standby
Æ /
key to confirm selection.
To set the TV to standby mode. To
switch the TV on again, press the
key once more or press the
9
Options
(See page 23)
to
, P + / – or
Note: when the TV is switched on,
the last viewed mode is displayed.
key.
10
Cancel
In digital mode, this key functions as an
exit key for MHEG teletext if no colour
keys links are available to exit
teletext mode.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
15
16
Mute
Turn off or on sound.
/
Numerical keys
/
For direct access to programmes.
For a two digit programme number, the
2nd digit must be entered shortly after
the first digital before the dash
disappears.
11
12
Screen information
17
In digital mode, display/exit the
information banner (see page 14).
In analogue mode, display/remove the
programme number, the sound mode,
the clock and the remaining time of
the sleep timer.
13
14
20
21
18
19
Active Control
Automatically adjusts the picture setting
for optimal picture quality continuously
under any signal conditions. (See page
36).
15
16
17
18
19
22
23
Digital TV / Radio
In digital mode, this key is used to access
digital radio stations. Press the
key
to access radio list. Note : To return
to digital video mode, press the
key again.
20
21
TV Guide
(see page 24)
Programme ( + P – )
Selects next or previous available
channel/source (or page in digital menu).
Alternate channel / Edit or back
space
11
12
Teletext
(See page 40-41).
22
Digital menu
To display / exit from the digital menu
(when TV is in digital mode).
In Analogue/Digital mode, it allows you
to alternate the previously viewed
programme and the current programme.
It is also used as an edit or back space
key when you are naming your favourite
channel.
13
14
OK
Confirms selection. Also access
program list in Digital mode.
Volume ( + VOL – )
To turn on sound louder or quieter.
23
Smart Picture /Sound
Accesses a series of predefined picture
and sound settings (see page 38).
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Overview of Digital
main menu and
sub-menus
1
2
Use the
control to select Digital mode.
key of the remote
From the digital mode, press the
key to display the setup menu.
3
Use the Î ï Í Æ keys to navigate,
select and adjust menu items.
Setup
Favourites
Name
List 1
List 2
Select TV channels.
Select Radio stations.
Add all services
Remove all services
Name
Select TV channels.
Select Radio stations.
Add all services
Remove all services
Name
List 3
List 4
Select TV channels.
Select Radio stations.
Add all services
Remove all services
Name
Select TV channels.
Select Radio stations.
Add all services
Remove all services
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Preferences
Language
Basque, Catalan, Croatian, Czech, Danish, Dutch,
English, Finnish, French, Gaelic, Gallegan, German,
Greek, Hungarian, Italian, Norwegian, Polish,
Portuguese, Russian, Serb, Slovak, Spanish,
Swedish, Turkish, Welsh
Audio
Subtitle/Teletext
Subtitling Mode
On, Off, Auto
Subtitles for hearing impaired
System
Yes, No
Cesky, Dansk, Deutsch, English, Español,
Français, Italiano, Magyar, Nederlands,
Norsk, Polski, Portugués, Suomi, Svenska
Location
Australia, Austria, Belgium, Czech, Denmark,
Finland, France, Germany, Greece, Hungary,
Italy, Netherlands, Norway, Poland, Portugal,
Spain, Sweden, Switzerland, United Kingdom
Country
Time zone
Information
System software
Current software version
Always accept new software
Yes, No
On, Off
Access restrictions
Set pin code protection
Maturity rating
TV channels
Radio stations
Change pin code
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
Installation
Service lists
Rearrange services
View new TV channels.
Listen to new Radio Stations.
Service setup
Add new services
Search
TV channels found.
Radio station found.
Other services found.
Store
Discard
Reinstall all services
Search
TV channels found.
Radio station found.
Other services found.
Store
Discard
Manual install service
Frequency
Network name
Signal quality
Services found
Store
Discard
Test reception
Frequency
Network name
Signal quality
Signal strength
12
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Switching on the TV
for the first time
When you switch on the TV set for the first
time, a menu will appear on screen.
5
6
Press the ï key to select Service
Scan to scan the available analogue and
digital channels.
11:28
Setup
Press the
key to start the
Language
Country
English
Español
Français
Italiano
Magyar
installation.
Time Zone
Service Scan
Note
If no digital channels are detected, press
key to switch to analogue mode.
Select your preferred language
Note
1
Press the Æ key to enter into
If at some point of time you decide to reset
to the factory default settings, press and hold
down the MENU key on the side of the TV
set for 5 seconds. A menu will appear on
the screen. Repeat steps 1 - 5 as if this was
the first time you have turned on the TV.
This activity will reset both the Digital and
Analogue mode to
Language mode and press the Î ï
keys to select your preferred language.
2
3
Press the
selection.
key to confirm
Press the Î ï keys to select Country
or Time Zone and press the Æ key to
enter into Country or Time Zone
mode.
factory default settings.
Caution
If you select a wrong country, the channel
numbering will not be according
to the standard for your country and
you may not receive all services or
nothing at all.
Note
The Language can be selected independently
from the Country.
4
Press the Î ï keys to select your
preferred Country or Time Zone and
the
key to confirm your selection.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Understanding the
information on
the banner
When you select a digital programme, an
information banner is displayed for a few
seconds at the top of the screen.
TXT
Indicates Analogue Teletext is available
in Digital mode.
ù Other languages are available and
can be selected in the options menu.
You can also select other languages by
8.1 Banner description
pressing the
key.
programme
u
The colour of the symbol (red, green,
yellow or blue) indicates the selected
Favourite list.
preset
number
start and
symbols
clock
end time
2
11:00-11:45
Snooker
TXT
10:38
Note
BBC 2
Minutes left : 22
A white symbol u will appear if the
programme is stored in one or more
of the favourite lists which are currently
not activated.
channel name
programme title
remaining time
of programme
The banner contains information on the
preset number, channel name, programme
duration, transmission clock, programme
title and the time remaining of the current
programme.
8.2 Symbols description
i
More information about this
programme is available : press the
key once to display and a second
time to remove it.
Subtitling is available : if you want to
display them, press the
the key to access the options
menu and select subtitles.
key or
14
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Service lists
9.1 Rearrange services
7
8
Press
is done.
key to confirm. The exchange
4
7
Repeat the operations
all the channels are in the required
order.
to
until
This menu allows you to change the order of
the stored digital channels and radio stations.
1
2
9
From the digital mode, press the
key to display the setup menu.
To return to previous menu, press the
Í key.
Use the ï key to select Installation
and press Æ twice to select the Service
lists menu.
10
Press the
key to exit the menu.
Setup
Installation
11:28
9.2 View new TV channels or Listen
to new Radio stations
Service lists
Rearrange services
Service setup
Test reception
View new TV channels
This menu allows you to check the
Listen to new Radio stations
availability of new TV channels or new radio
stations that have been launched by the
broadcaster after the initial installation.
Manage service lists
Close
1
2
From the digital mode, press the
key to display the setup menu.
3
Use the Î ï keys to select Rearrange
Use the ï key to select Installation
and press Æ twice to select the Service
lists menu.
services and press Æ key.
Setup
Installation
11:28
3
4
Use the Î ï keys to select View new
TV channels or Listen to new Radio
station.
Rearrange services
1
2
3
4
5
6
7
8
9
_
_
_
_
_
_
_
_
_
View new TV channels
Listen to new Radio stations
If new services are availables, press Æ
to enter into the list and use the Î ï
keys to move through the list.
Change preset location of services
5
6
To return to previous menu, press the
Í key.
Close
Press the
key to exit the menu.
4
5
Use the Î ï keys to select the channel
you want to exchange.
Press
key to activate.
If you want to uninstall the selected
channel, press the red key.
6
Select (Î ï) the new channel number
15
Download from Www.Somanuals.com. All Manuals Search And Download.
10 Service setup
The search begins and only new channels
will be stored and added to the channel
list menu. The percentage of the
installation that has been completed
and the number of channels found is
displayed. When the search is completed,
10.1 Add new services
This menu allows you to search for new TV
channels or radio stations that have been
launched by the broadcaster after the initial
installation.
press the
services.
key to accept the new
1
2
3
From the digital mode, press the
key to display the setup menu.
5
6
To return to previous menu, press the
Í key.
Use the ï key to select installation and
press Æ key.
Press the
key to exit the menu.
Select Service setup (ï) and press Æ
key.
Setup
Installation
11:28
10.2 Reinstall all services
Service lists
Service setup
Test reception
Add new services
This menu allows you to reinstall all the
digital TV channels and radio stations.
Reinstall all services
Manual install services
1
2
3
4
From the digital mode, press the
key to display the setup menu.
Install and manage services
Close
Use the ï key to select installation and
press Æ key.
Select Service setup (ï) and press Æ
key.
4
Press Æ to add new services and press
key to activate the installation.
Select Reinstall all services (ï) and
press Æ key.
Setup
Installation Service setup
11:28
Add new services
Reinstall all services
Manual Install services
Search
Setup
11:28
TV channels found
Radio stations found
Other services found
Store
Installation Service setup
Add new services
Reinstall all services
Manual Install services
Search
TV channels found
Radio stations found
Other services found
Store
Discard
Scan for new services
Discard
Close
Reinstall will remove all service settings
Close
16
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Press the
installation.
key to start the
5
Use the
frequency of your target channel and
press key to start the searching
of channels. When the search is
completed, the menu will indicate the
number of digital services found.
to
key to input
A search is then made for all digital
services which are then stored
automatically. When the search is
completed, the menu will indicate the
number of digital services found.
6
7
6
7
Press the
key to store the services.
Press
key to store the services.
To return to previous menu, press the
Í key.
To return to previous menu, press the
Í key.
8
Press the
key to exit the menu.
8
Press the
key to exit the menu.
10.3 Manual install services
This menu allows you to scan maually
services by keying in the frequency of your
target channel.
1
2
3
4
From the digital mode, press the
key to display the setup menu.
Use the ï key to select installation and
press Æ key.
Select Service setup (ï) and press Æ
key.
Select Manual install services (ï) and
press Æ key.
Setup
11:28
Installation > Service setup
Add new services
Reinstall all services
Frequency
Network name
Signal quality
Signal strength
Services found
Store
Manual install services
Discard
Manual install services
Close
17
Download from Www.Somanuals.com. All Manuals Search And Download.
11 Test reception
This menu allows you to check the strengh
of the signal you are receiving through your
aerial.
5
6
7
After entering the frequency, use the
key to exit Frequency slot.
To return to previous menu, press the
Í key.
1
2
From the digital mode, press the
key to display the setup menu.
Press the
key to exit the menu.
Use the ï key to select Installation
and press the Æ key.
Setup
Installation
11:28
Service lists
Frequency
Service setup
Test reception
Network name
Signal quality
Signal strength
Test signal quality
Close
3
4
Use the ï key to select Test
reception and press the Æ key. You
obtain an indication of the actual
programme frequency, the network
name, the signal quality and strength.
Use the Æ key to enter the Frequency
slot and use the
to
keys to
enter the frequency of the digital channel
you want to test. Use the Æ key to
move to the next character space.
If the test reception indicates that the
signal strength is indeed poor, you
can try improving, renewing, adjusting
or updating the aerial. It is however
advisable to contact a specialised aerial
installer in order to achieve best results.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Preferences
This menu allows you to select your
preferred language or to make changes to
the location (country and time zone).
• Subtitles for hearing impaired : to
activate or deactivate the specific subtitling
for hearing impaired (if made available by
the broadcaster).
1
2
From the digital mode, press the
key to display the setup menu.
Use the ï key to select Preferences
and press Æ key.
• System : to select the menu language.
Note
If you have selected the wrong language
for one reason or another and do not
understand the selected language to operate
the set, do the following to bring you back
to your preferred language.
Setup
Preferences
11:28
Language
Location
Audio
Subtitle / Teletext
Subtitling Mode
•
Press the
screen.
key to exit menu from
Subtitling for hearing impaired
System
• Press the
key again to display menu.
• Press the key to select the second item
on the menu and the key to enter into the
next menu level.
Select your preferred language
Close
• Press the key to again and use the
to select the fifth menu item.
key
3
Select Language or Location (ï) and
• Press the key to enter into the next menu
press Æ key.
level.
4
Use the Î ï keys to select a setting
and press Æ key to enter into the sub-
menu. Make your adjustment and press
key or Í key to exit.
• Press the Î ï keys to select correct
language.
• Press the
key to confirm selection.
key to exit menu from
5
6
•
Press the
screen.
To return to previous menu, press the
Í key.
Location settings
Press the
key to exit the menu.
• Country : to select the country where
you are located.
Language default settings
Caution
If you select a wrong country, the
channel numbering will not be according
to the standard for your country and
you may not receive all services or
nothing at all. Note that the Language
can be selected independently from the
Country.
• Audio : to select the audio sound
language.
• Subtitle/Teletext : to select the
subtitle/teletext language.
• Subtitling mode : off, on or auto
(subtitle only displayed in case of original
audio transmission).
• Time zone : to select the time zone
where you are located.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
13 Access restrictions
This menu allows you to set up the access
restrictions for the digital channels.
• TV channels: select the TV channel you
want to lock and press key.
• Radio station: select the radio station
you want to lock and press key.
1
2
3
From the digital mode, press the
key to display the setup menu.
• Change pin code: press Æ key to
enter in the menu. Follow the on-screen
instruction to change your access code.
The default pin code is 1234. If you have
forgotten your personal code, you can
reset to the default pin code (1234) by
entering the universal code 0711.
Use the ï key to select Access
restriction and press the Æ key.
Press the Æ key to enter into the
Set pin code protection menu.
Access restrictions
11:28
Off
Set pin code protection
Maturity rating
On
Note
TV channels
Radio stations
Change pin code
The TV is equipped with a Common
Interface (CI) slot (see page 28).
This CI module can be obtained when you
subscribe to service providers like Pay
TV or other service providers. The
CI module does not come with the TV
set.
Switch pin code protection ‘on’ or ‘off’
Close
4
Use the Í Æ keys to set to On option
and press key to exit.You can then
access the other adjustments.
The Access Restrictions menu will show
the CI Access Restrictions when a CI
module is installed. The CI module is
responsible for the messages and texts
on screen. In case of failure or strange
behaviour, you must call your CI service
provider.
Warning
The moment you use any kind of access
restriction, you need to fill in the pin
code when you schedule a programme
for recording.
5
6
To return to previous menu, press the
Í key.
Press the
key to exit the menu.
•
Maturity rating : select your preferred
rating to lock the channel. Maturity rating
will only block certain programmes if the
broadcaster provides data with the
programme.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
14 Setting up your favourite
list
This menu enables you to create a favourite
list with your prefered TV channels and
radio stations. For example, each member of
your family can create his/her own favourite
list.
• Select TV channels : use the Î ï keys
to select your favourite TV channels and
confirm with
key. Press Í key to exit.
• Select radio stations : use the Î ï
keys to select your favourite radio station
and confirm with
exit.
key. Press Í key to
1
From the digital mode, press the
key to display the setup menu.
•
Add all services : press
key if you
want to add all the service into your
favourite list.
Setup
11:28
Favourites
Preferences
Information
List 1
List 2
List 3
List 4
• Remove all services : press
you want to remove all the service from
your favourite list.
key if
Access restrictions
Installation
5
6
To return to previous menu, press the
Í key.
Make changes to your lists of favourite services
Close
Press the
key to exit the menu.
2
Press Æ to enter into the favourites list
menu. You have the choice to create
4 different favourite lists.
Your favourite list can be selected via
the options menu (see next page).
3
Use the Î ï keys to select your
Favourite list : List 1, List 2, List 3
or List 4 and press Æ key.
4
Use the Î ï keys to select a setting and
press Æ key to enter into the sub-menu.
• Name : use the Í Æ keys to move
around the name display area (16
characters) and the P + / – keys to select
the characters. To edit any character, use
the
key. When the name has been
key to exit.
entered, press
21
Download from Www.Somanuals.com. All Manuals Search And Download.
15 Information
This menu provides information about the
software version and the installation of new
software.
Once accepted the download will take
place at the designated time and date.
Note
1
The TV must be put into standby when the
download is due in order for it to take place.
From the digital mode, press the
key to display the setup menu.
2
Use the ï key to select information and
Off Air Downloading of new software
press Æ key twice.
Whenever a new software is available, it is
advisable to always accept and download the
software.
Setup
11:28
Favourites
Preferences
Information
Access restrictions
Installation
System software
• In case new software is available, you
will see a message when you switch on the
TV. A message indicating the date and the
duration of download is indicated in the
menu. Press the
key to proceed.
Important : Leave your TV in standby
to allow upgrade to take place. Do not
power off your main switch.
Provide information on problem reports and installing new software
Close
• If a problem occurred during the download
of the new software, you will be informed
of the next scheduled software download.
The software version is displayed.
3
Use the Æ key to enter the selection
Press the
key to proceed to use your
mode.
TV normally.
4
Use the Í Æ keys to select Yes or
No mode. You can activate the menu
to automatically accept any software
update of your digital TV through off-air
downloading. Normally the product will
detect if an update is available while it is
in standby mode. Next time the
•
If download is successful, a congratulatory
message will appear. Press the
key to
accept. New software and upgrade
instructions may also be obtained from the
5
To return to previous menu, press the
television is turned on a message will
appear on the screen indicating new
Í key.
software is available. Selecting the
activates the software download.
key
6
Press the
key to exit the menu.
The software download menu will give a
description of the software together with
the date and time of the download. This
may update certain menus, functions or
add new features, but the general way in
which the TV operate will not change.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
16
Using the Options
menu
This menu gives you direct access to the:
favourite list, the language selection and
some other selections.
•
•
Audio language : to temporarily
change the audio sound language.
To permanently change the audio and
subtitle languages, use the Preferences
menu (see page 18).
1
From the digital mode, press the white
key to display the options menu.
Mode : you can choose to only have
radio stations, TV channels or services
without audio or video.
Options
11:28
Note (for the UK only)
The TV list will contain both radio
stations and TV channels
None
List 1
List 2
List 3
List 4
Favourites
Subtitle language
Audio language
Mode
•
Banner duration : to select the
duration for which the banner is visible.
Selects the active favourite list
Exit
3
Press the white
menu.
key to exit the
2
Use the Î ï keys to select a setting
and press Æ key to enter the sub-menu.
•
Favourites : use the Î ï keys to select
your favourite list and confirm with
key.
Note
The “none” option deactivates any
favourite list. To create your own
favourite list, see page 21.
•
Subtitle language : use the Î ï keys
to temporarily change the language and
confirm with
key.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
17 TV Guide
The TV guide is an Electronic Programme
Guide that provides you with a quick and
easy way to view a complete list of digital
programmes as you would in a newspaper
or TV magazine. You can navigate through
the list of digital programmes and obtain
detailed information on the programmes.
You can also program the TV to provide a
digital channel to be recorded.
• Top (yellow key) : to go directly to the
top of the list.
• Close (blue key) : to exit from the TV
guide.
• Options (white ÆÆ key) : with this menu,
you can select your favourite list, mode or
themes. Themes are areas of interest, you
can for example, decide to display only :
drama, news, movie, ...
1
From the digital mode, press the
key to display the TV guide :
5
Press the
display more information about the
selected programme (if available).
key if you want to
1
17:28
BBC
6
Now/Next
Now
Today
Next
Press the
key to exit the menu.
Preset/Servcie
See it saw
Snooker
Trisha
-
1. BBC
Microsoap
Ice Skating
This morning
-
2. BBC TWO
3. ITC Channel 3
4. Channel 4
5. ITV 2
Gmtv2
This afternoon
6. BBC CHOICE
Oakie Doke Bodger & Badger
Top
Close
Options
A list of all the digital programmes in the
currently selected favourite list is displayed.
2
Use the ï key to enter into the
Preset/service list or press Æ key to
access Today list.
3
4
Use the Í Æ keys to select a
programme.
The TV guide features are displayed
at the bottom of the screen. Use the
coloured keys red, green, yellow, blue or
white to activate them.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
18 Recording function
(Not applicable for this model)
This feature enables you to record a digital
channel while the TV is in standby mode.
You will still have to programme your video
recorder. If you wish to continue watching
another digital channel after setting a timer,
you can do so by changing channels in the
normal way.
4
Use the Î ï keys to select a setting
and press Æ to enter into the sub-
menu. Make your adjustment and
press
key or Í key to exit.
• Name : the selected programme will
be displayed here.
Important : Do not switch off the TV
and the mains when a recording has been
programmed. The TV must be in standby for
recording to take place.
• Service : you can change the number
of the programme you want to record.
Press
key to confirm.
Note
It is only possible to change to a
number that is in the currently selected
favourite list.
1
2
From the digital mode, press the
key to display the TV guide.
Use the ï key to enter into the Preset/
Service list or press Æ key to access
Today list.
• Enter your pin code if locked :
enter your secret code only if you have
activated the access restriction feature
(see page 19). Press
key to confirm.
3
Press the RED key to call up the
Record menu.
• Day & Month : enter the date by
using the P – / + keys. Press
key to exit
11:28
2 BBC 2
• Start time : enter the start time.
• End time : enter the end time.
• Audio language : select your language
Name
Service
See it saw
2 BBC 2
Enter your pin code if locked
Day & Month
16/02
12:15
12:30
English
Start time
End time
Audio language
and confirm with
key.
• Subtitle language : make your
Store
Cancel
Close
selection and confirm with
key.
• Subtitles for hearing impaired :
select Yes or No and confirm with
key.
• Occurrence : select Once, Daily or
Weekly and confirm with
key.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
(Not applicable for this model)
5
Press the RED key to store your
recording. The TV guide reappears.
You can press the GREEN key to
display the list of recordings you have
set.
6
If you have finished watching television,
you must leave it in standby in order
for the recording programme to be
activated.
Important
Do not switch off the TV and the mains
when a recording has been programmed.
The TV must be in standby for recording
to take place.
7
If you are watching another digital
channel when the timer is due to start,
the timer alarm will sound and present
you with the option of switching
channels or continuing to watch the
current channel. If you choose to switch
channels, recording will not take place.
Note
Your future recording might be
interrupted or affected if you press
either the
or
key
immediately when the set is wakeup
from standby. Future recording might
also be interrupted or affected when
either EXT 1/ EXT 2 source is
connected when the set is wakeup
from standby.
To avoid the interruption of your future
recording, it is recommended that you
stay in digital mode for about a minute if
a recording has been programmed.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
19 Digital teletext (MHEG)
Available in U.K. only
3
When you have finished watching
teletext, select a different channel with
P – / + keys or follow the on screen
instructions to return to picture.
Digital teletext services differ greatly from
analogue teletext. When you switch to a
Digital teletext service, the images you see
contain graphics and text which are laid out
and controlled in a manner decided by the
broadcaster. Some digital channels, which you
select like any other channel, offer dedicated
teletext services. Some digital channels also
offer information on the programme being
broadcast (a message or an instruction may
appear on the screen).
When you switch to a digital channel
with links to a telext service, software is
downloaded in the background to enable the
teletext function. You will have to wait for
a while before you press the
allow the software download to complete. If
you press the key before the download
key to
is complete, there will be a short delay
before the teletext screen is displayed.
Under certain circumstances, Digital text or
interactive services may have priority over
subtitles. This can result in the subtitles not
automatically reapperaing when leaving Digital
text or interactive services on a channel
which is broadcasting subtitles. In these cases,
subtiltes can be intialised either by toggling
While navigating the digital teletext, there is
a short delay while the page downloads. A
prompt or message is often broadcast on the
page to let you know the progress.
the
key on the remote control or by
Analogue teletext in Digital mode
changing channel.
Note
Available in all countries
1
2
To use the digital teletext, follow the
instructions on screen.
TXT
• If you see an icon
on a digital
channel without digital telextext services,
it indicates Analogue Teletext is available
in Digital mode.
Depending on the service, you can
be asked to use the Í Æ Î ï (cursor
keys),
(colour keys),
numerical
• Press the
teletext.
key to access Analogue
(Teletext On/Off key) and
sometimes the
keys.
/
Note
If UK country is selected during
installation, press and hold
at least 3 seconds.
Note
key for
If no colour key links are available
in the Digital Teletext to allow you to
exit teletext mode, use the
instead.
key
• To use Analogue Teletext functions, see
page 40 and 41.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
20 Using the Conditional
Access Module (CAM)
2
3
The Conditional Access Module (CAM)
menu provides access to functions contained
on the CAM. The module can be inserted
into the Common Interface (CI) slot located
at the backside (facing downwards) of the
TV.
Some modules come with a viewing
card. When using this type of module,
first insert the viewing card into the
module. Ensure that the arrow on the
viewing card faces the arrow of the
module before inserting into the
module slot.
Note
Insert the module into the Common
Interface (CI) slot on the TV.
This Common Interface (CI) module does
not come with the TV set. It can only be
obtained when you subscribe to service
providers like Pay TV or other service
providers.
4
5
Switch on the TV.
Press the
key to display the
setup menu.
6
7
8
Use the ï key to select Access
restriction and press the Æ key.
Press the Æ key to enter into the
Conditional Access Module menu.
IMPORTANT
Always switch the TV off before inserting or
removing the module.
Press
button as indicated on the
Inserting the CAM
screen to access the CAM’s functions
(see page 20).
1
Switch off the TV.
IMPORTANT
Connectors at
rear of TV (facing
downward)
If no module is inserted, or the module
is not inserted properly, the Conditional
Access Module menu will not be displayed.
(If you have inserted a module, check that
it is fully inserted in the correct manner as
mentioned in step 3 above).
Common
Interface slot
The functions that now appear on screen
are dependent on the contents of the
selected Conditional Access Module in your
country. Refer to the instruction supplied
with the module or contact the vendor.
Module
28
Download from Www.Somanuals.com. All Manuals Search And Download.
21 Automatic tuning of
analogue programmes
Auto Store
This menu allows you to automatically search
for all the analogue programmes available in
your region.
Program
TV
3
196 MHz
Before you automatically search for all the
analogue programmes, ensure the TV is in
analogue mode. If it is in digital mode, press
the
(Analogue / Digital) key to enter
the analogue mode.
IMPORTANT
To exit or interrupt the search before it
is completed, press the key. If you
1
Press the
key.
interrupt search during auto store, not all
channels will be stored. For all channels to
be stored, you need to do a complete auto
store search again.
Main
Brightness
Colour
Picture
Sound
Features
Install
Contrast
Sharpness
Colour Temp
Contrast+
NR
Note
ATS (Automatic Tuning System)
feature
If the transmitter or cable network sends
the automatic sort signal, the programmes
will be numbered correctly. In this case,
the installation is complete. If this is not the
case, you can use the Sort menu to number
the programmes to your preference.
2
Press the Î / ï key repeatedly to
select Install and the Æ /
key to
enter the Install menu.
Main
Picture
Sound
Features
Install
Auto Store
Manual Store
Sort
Name
Fav. Program
ACI (Automatic Channel Installation)
feature
If a cable system or a TV channel which
broadcasts ACI is detected, a programme
list appears. Without ACI broadcast, the
channels are numbered according to your
language and country selection. You can use
the Sort menu to renumber them.
3
Press the ï key to select Auto Store
and the Æ / key to start automatic
searching of the channels. All the
available TV programmes will be stored.
This operation takes a few minutes. The
display shows the progress of the search
and the number of programmes found.
Note
You cannot change the Language or
Country in Analogue mode. If you want
to change the Language or Country,
you have to exit Analogue mode and
enter into Digital mode to do so (refer to
“Preferences”on page 18).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
22 Manual tuning of
analogue programmes
This menu is used to store the programmes
one at a time.
5
System:
Press the Î ï keys to select
Europe (automatic detection),
France (LL’ standard),
UK (I standard),
West Europe (BG standard) or
East Europe (DK standard).
1
2
Press the
Press the Î ï keys repeatedly to
key.
select Install and the Æ /
key to
enter the Install menu.
Press the Æ /
key to confirm
selected system.
Main
Picture
Sound
Features
Install
Auto Store
Manual Store
Sort
Name
Fav. Program
6
Search:
Press the Æ key. The search starts.
Once a programme is found, the
scanning stops and its name is displayed
(if available). Go to the next step. If
you know the frequency of the
required programme, this can be
3
Press the ï key to select
Manual Store and the Æ /
enter Manual Store menu.
entered directly using the
keys.
to
key to
7
8
9
Program No.:
Enter the required number with the
Install
System
Search
Program No.
Fine Tune
Store
to
or Î ï keys.
Auto Store
Manual Store
Sort
Name
Fav. Program
Fine Tune:
If the reception is not satisfactory,
adjust using the Î ï keys.
Store:
To store the changes, press Æ /
key. The programme is now stored.
4
Press the Î ï keys to select the items
in the Manual Store menu to adjust or
activate.
10
11
6
9
Repeat steps
to
for each
programme to be stored.
Manual store
To return to previous menu, press the
Í key.
System
Europe
Search
France
Program No.
Fine Tune
Store
UK
West Europe
East Europe
12
To exit the menu, press the
key.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
23 Programme Sort
Sort feature allows you to change the
programme number for a particular station.
Install
100
Auto Store
Manual Store
Sort
Name
Fav. Program
001
002
003
004
005
006
007
008
1
Press the
key.
2
3
4
Press the Î / ï key repeatedly to
select Install and the Æ /
enter the Install menu.
key to
Main
Picture
Sound
Features
Install
5
Press the Î ï keys to select the new
programme number and confirm with
the Í key. (The arrow points to
the right and sorting is completed).
Auto Store
Manual Store
Sort
Name
Fav. Program
Install
100
Auto Store
Manual Store
Sort
Name
Fav. Program
001
002
003
004
005
006
007
008
Press the ï key to select Sort and the
Æ / key to enter sort mode.
Install
100
Auto Store
Manual Store
Sort
Name
Fav. Program
001
002
003
004
005
006
007
008
6
4
5
Repeat steps
and
for each
programme number you wish to re-
number.
7
8
To return to previous menu, press the
Í key.
Select the programme number you
want to move using the Î ï keys and
the Æ key to enter sorting mode
(The arrow cursor now points to the
left).
To exit the menu, press the
key.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
24 Naming of Channel
If preferred, you can assign a name to the
TV channel.
Install
106
Auto Store
Manual Store
Sort
Name
Fav. Program
001
002
003
004
005
006
007
008
1
Press the
key.
z
2
Press the Î / ï key repeatedly to
select Install and the Æ /
key to
enter the Install menu.
Main
Picture
Sound
Features
Install
OK
7
Press Æ /
key until the name
Auto Store
Manual Store
Sort
Name
Fav. Program
appears at the top left hand corner
of the TV screen. The name is now
stored.
8
9
To return to previous menu, press the
Í key.
3
Press the ï key repeatedly to select
To exit the menu, press the
key.
Name and the Æ /
key to
enter Name mode.
Install
100
Auto Store
Manual Store
Sort
Name
Fav. Program
001
002
003
004
005
006
007
008
4
5
6
Press the Î ï keys to select the
channel you want to name.
Press the Æ key to move to the first
name display area.
Press the Î ï keys to select the
characters (maximum of 5 characters)
and press the Í Æ keys to move
around the name display area.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
25 Selecting your
Favourite Programmes
This feature allows you to skip programmes
that you do not watch often and only keep
your favourite programmes.
5
Press the Æ /
key to skip the
programme. The $ on the right of the
menu will disappear indicating the
programme is skipped.
Note: Once a programme is skipped, you
cannot access it by the P – / + key. You can
only access the programme by the Digit 0 -9
keys.
100
Install
001
002
003
004
005
006
007
008
Auto Store
Manual Store
Sort
Name
Fav. Program
1
2
Press the
key.
Press the Î / ï key repeatedly to
select Install and the Æ /
key to
enter the Install menu.
Main
Picture
Sound
Features
Install
6
7
To return to previous menu, press
the Í key.
Auto Store
Manual Store
Sort
Name
Fav. Program
To exit the menu, press the
key.
Tip
• To add back the skipped programmes to
3
4
Press the ï key to select
Fav. Program and the Æ /
to enter Fav. Program list.
1
3
your favourite list, repeat steps
to
.
key
• Press the Î / ï key repeatedly to
select the skipped programme you want
Press the Î / ï key repeatedly to
select programme you want to skip.
to add back to your favourite programme
list.
• Press the Æ /
programme. The $ will appear indicating
the programme is now restored.
key to unskip a
100
Install
001
002
003
004
005
006
007
008
Auto Store
Manual Store
Sort
Name
Fav. Program
33
Download from Www.Somanuals.com. All Manuals Search And Download.
26 Features
26.1 Timer
Sleep: to select a time period in which
the set will switch to standby mode upon
reaching the selected time period.
The Timer feature allows you to set the TV
to switch to another channel at a specified
time while you are watching another
Select Off option to deactivate the feature.
channel. You can also use it as an alarm to
switch on the TV at a specified time from
standby mode. For the timer to function,
the set must not be switched off. Once the
set is switched off, the timer is disabled.
Note
During the last minute of a Sleep time
setting, an on-screen countdown will be
displayed. Press any button on the remote
control to cancel the Sleep shut down.
Time: enter the current time.
1
2
Press
key.
Press Î ï keys repeatedly to select
Features and the Æ/
Features menu.
Start Time: enter the start time.
Stop Time: enter the standby time.
key to enter
Main
Picture
Sound
Program No.: enter the number of the
channel for the wake-up alarm.
Timer
Child Lock
Features
Install
Parental Lock
Active Control
Activate: the settings include:
– Once for a single alarm,
– Daily for each day,
– Off to cancel.
3
4
Press Æ /
menu.
key to access Timer
6
Press
key on the remote control to
put the TV set in standby mode. The
TV will automatically come on at the
programmed time. If you leave the TV
set on, it will just change channel at
the Start Time and will go to standby
mode at the Stop Time.
Press Î ï keys to select a Timer item.
Timer
Sleep
Time
Start Time
Stop Time
Program No.
Active
- - : - -
5
To make adjustments to the timer
setting, use the Í, Æ, Î, ï or Digit
0-9 keys.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
26.2 Parental Lock
Parental Lock
Lock Program
Change Code
Clear All
106
The Parental Lock feature allows you to
lock channels to prevent your children from
watching certain programmes.
001
002
003
004
005
006
007
008
Lock All
1
2
Press
key.
Press Î ï keys repeatedly to select
Features and press the Æ/
key to
enter Features menu.
In the Parental Lock menu, use the Î, ï,
Í, Æ, Digit 0-9 and keys to access
and activate the Parental Lock functions.
Main
Picture
Sound
Features
Install
Timer
Child Lock
Parental Lock
Active Control
Description of the settings:
Lock Program
Lock individual program. Press Æ key to
enter Lock Program mode and the Î
ï keys to select the program to lock or
unlock. Press the Í Æ keys to lock or
unlock selected program. A keylock symbol
+ appears besides the locked channel
number. To exit from Lock Program
mode and return to Parental Lock menu,
3
Press Î ï keys repeatedly to select
Parental Lock and press Æ /
key
to enter Parental Lock mode.
press
key.
Change Code
Features
Key in your new four-digit code using the
Digit 0-9 keys and confirm by keying in the
new four-digit again.
Timer
* * * *
Access Code
Child Lock
Parental Lock
Active Control
Clear All
Press Æ key to unlock all locked channels.
Lock All
Press Æ key to lock all locked channels.
4
5
Key in the access code 0711 by the
Digit 0-9 keys. A message Incorrect
will appear. Key in the access code 0711
again.
Note
If you switch on the TV set and select a
program that has been locked, you need
to key in the Access Code to enter the
selected locked channel. To unlock the
channel, go the Lock Program in the
Parent Lock menu and press the Í Æ keys
(keylock symbol + disappears).
The TV will then prompt you to change
code. Key in your own 4-digit code by
the Digit 0-9 keys and confirm the new
code. Once the new code is confirmed,
the Parental Lock menu will appear.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
26.4 Active Control
26.3 Child Lock
Automatically adjusts the picture setting for
optimal picture quality continuously under
any signal conditions.
The side controls of the TV will be locked
when you select the On option in the Child
Lock menu. You need to hide the remote
control from your children to prevent them
from watching TV.
1
2
Press
key.
Press Î ï keys repeatedly to select
1
2
Press
key.
Features and press the Æ/
key to
enter Features menu
Press Î ï keys repeatedly until
Features is selected and press Æ /
key to access Features menu.
3
Press Î ï keys repeatedly to select
Active Control and press the Æ /
key to enter Active Control mode.
3
Press ï key to select Child Lock and
press the Æ /
key to access Child
Lock mode.
Features
Off
On
Timer
Child Lock
Parental Lock
Active Control
Features
Timer
Child Lock
Parental Lock
Active Control
Off
On
4
Press Î ï keys to select On or Off
option.
4
Press Î ï keys to select On or Off
option.
5
6
Press Æ /
key to activate/deactivate
On or Off option.
5
6
Press Æ /
On or Off option.
key to activate/deactivate
To return to previous menu, press the
Í key.
To return to previous menu, press the
Í key.
7
To exit the menu, press the
key.
7
To exit the menu, press the
key.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
27 Picture and Sound
settings
You can adjust the picture and sound settings
in the Picture and Sound menu.
Contrast: this changes the difference
between the light and dark tones within the
contrast range of the TV.
1
2
Press the
key.
Sharpness: this increases or decreases the
sharpness level to improve details in the
picture.
Press the Î ï keys to select Picture
or Sound.
3
Press Æ /
Sound menu.
key to enter Picture or
Colour Temp.: this changes the colour
setting: Cool (more blue), Normal (balanced)
or Warm (more red).
Picture
Brightness
Colour
Contrast+: Increases the contrast range of
the TV. Select On option to activate feature.
100
Contrast
Sharpness
Colour Temp
Contrast+
NR
63
NR: improves “noisy” picture (little dots
on picture) due to weak signal transmission.
Select On option to activate feature.
0
Description of the Sound settings
Equalizer: to adjust the sound tone.
Sound
Equalizer
Balance
AVL
120HZ
200HZ
500HZ
1200HZ
3KHZ
Balance: this balances the sound on the left
and right speakers.
Incr.Surround
AVL: (Automatic Volume Leveller):
this is used to limit sudden increases in
sound, especially on programme change
or advertising slots.
7500HZ
12KHZ
4
5
Press Î ï keys to select a Picture
or Sound setting.
Incr. Surround: select between
Incredible Surround and Stereo when in
stereo transmission and between Mono
and Spatial when in Mono transmission.
Press Æ /
key to enter the Picture
or Sound setting.
6
7
8
Press Î ï keys to adjust the Picture
or Sound setting.
To return to previous menu, press the
Í key.
To exit the menu, press the
key.
Description of the Picture settings
Brightness : this changes picture brilliance.
Colour : this changes the intensity of the
colour.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
28 Smart Picture and
Sound
Smart Picture feature offers you a choice
of 5 picture settings namely : Rich, Natural,
Soft, Multimedia and Personal.
Definition of Picture Settings
Rich
: Brilliant and sharp picture
settings suitable for bright
environment and for use in
demonstrations to show
off the quality of the TV
on good sources.
Press the
button repeatedly to cycle
through the settings to select your desired
mode.
Natural
Soft
Natural
Soft
: Reference mode for living
room conditions and
average signals.
or
Multimedia
Rich
: Intended for bad-quality
signals. Suitable for living
room viewing.
Personal
Note : The Personal setting is the
setting that you set up using the Picture
menu in the main menu. This is the only
setting in the Smart Picture setting that can
be changed. All other settings are pre-set at
the factory for your convenience.
Multimedia : Best for graphical
applications.
Personal
: Pictures settings are set to
your preference.
Smart Sound feature offers you a choice
of 4 sound settings namely : Movies, Music,
Voice, and Personal.
Definition of Sound Settings
Press the
button repeatedly to cycle
through the settings to select your desired
mode.
Movies
: Emphasize sensation to
action.
Music
: Emphasize low tone.
Music
or
Voice
:
Emphasize high tone.
Voice
Movies
Personal
: Sound settings are set to
your preference.
Personal
Note : The Personal setting is the
setting that you set up using the Sound menu
in the main menu. This is the only setting in
the Smart Sound setting that can be changed.
All other settings are pre-set at the factory
for your convenience.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Screen Formats
The pictures you receive may be transmitted
in 16:9 format (wide screen) or 4:3 format
(conventional screen). 4:3 pictures will
have a black band at the left and right of
the screen. The screen formatting function
allows you to optimise the picture display
on screen.
Subtitle Zoom
This mode is used to display 4:3 pictures
using the full surface of the screen leaving
the sub-titles visible. Part of the top of the
picture is clipped off.
Press the
key repeatedly to cycle
through the different screen formats and
select your preferred format.
4:3
Super Wide
The picture is reproduced in 4:3 format and
a black band is displayed on either side of
the picture.
This mode is used to display 4:3 pictures
using the full surface of the screen by
enlarging the sides of the picture.
Movie Expand
14:9
Widescreen
The picture is enlarged to 14:9 format, a
thin black band remains on both sides of the
picture. Some of the top and bottom of the
picture is clipped off.
The picture is displayed in the original
proportions of images transmitted in 16:9
format.
Note
If you display a 4:3 picture in this mode, it
will be stretched horizontally.
Movie Expand
16:9
The picture is enlarged to 16:9 format. This
mode is recommended when displaying
pictures which have black bands at the
top and bottom (letterbox format). In this
mode, large parts of the top and the bottom
of the picture are clipped off.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Teletext
1
Teletext On/Off
Teletext is an information system broadcast
by certain channels which can be consulted
like a newspaper. It also offers access to
subtitles for viewers with hearing problems
or who are not familiar with the transmission
audio language (cable networks, satellite
channels, etc.).
Press this key to switch on teletext
display. A contents page appears with a
list of items that can be accessed. Each
item has a corresponding 3 digit page
number. If the selected channel does not
broadcast teletext, the indication 100
will be displayed and the screen will
remain blank. Proceed to exit teletext
by pressing the
key again.
2
Selecting a page
5
Enter the number of the page required
using the 0 to 9 keys or P –/+ keys.
Example: page 120, enter 120. The
number is displayed at the top left
corner of the screen. When the page is
located, the counter stops searching and
the page is displayed. Repeat this
1
3
operation to view another page. If the
counter continues to search, this means
that the page is not transmitted. In that
case, select another number.
3
Direct access to the items
2
Colour areas are displayed at the
bottom of the screen. The 4 colour
keys are used to access the items or
corresponding pages. The colour areas
flash when the item or the page is not
yet available.
2
4
4
5
Contents
This returns you to the contents page
(usually page 100 or hitlist menu).
Page hold
Certain pages contain sub-pages which
are automatically displayed successively.
This key is used to stop or resume
sub-page progression. The indication
appears top left. Use the Í Æ keys to
select previous or next sub-page.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Picture/Teletext
• Press the
• Press the
key.
key to show Teletext on
the right and the picture on the left of
the screen.
9
9
6
8
• Press the
key to return to a full
teletext mode.
• Press the
9
key to return to a full
screen picture.
7
7
9
Favourite pages
Note: only available in RF Analogue.
Instead of the standard colour areas
displayed at the bottom of the screen,
you can store 4 favourite pages on the
first 40 channels which can then be
accessed using the coloured keys (red,
green, yellow, blue). Once set, these
favourite pages will become the default
every time teletext is selected.
9
9
To store the favourite pages, proceed as
follows:
• Press the
key to change to
favourite page mode.
• Use the
keys to enter the
teletext page that you want to store as
a favourite page.
• Press and hold the colour key of your
choice for about 5 seconds. The page is
now stored.
• Repeat steps 2 to 3 with the other
colour keys.
6
7
Hidden information
To display or hide the concealed
information such as solutions to games
or riddles.
• To exit favourite page mode, press the
key. To exit teletext mode,
press
Note
key.
Enlarge a page
This allows you to display the top or
bottom part of the page. Pressing it
again will return the page to normal size.
To clear favourite pages, press and hold
key for about 5 seconds.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
31 Using the TV as a PC
Monitor
3
Press the Î ï key to select the
settings and the Í Æ key to select or
adjust setting.
Your TV can be used as a computer
monitor.
Note : PC connection is
only available via HDMI connector. VGA
4
5
connection is not supported.
To return to previous menu, press the
Í key.
31.1
Connecting the PC equipment
To exit the menu, press the
key.
Important
For the TV to function as a PC monitor, the
following steps must be taken.
Picture menu
• The Picture menu comprises
Brightness, Contrast, Sharpness,
1
Colour Temp., Contrast+ Horizontal
Shift and Vertical Shift features.
• Except for the Horizontal Shift and the
Vertical Shift features, all the other
features work exactly in the same way
as the features in the TV Picture menu
(see page 37).
• Horizontal Shift feature allows you to
adjust horizontal position of the image.
Vertical Shift feature allows you to
adjust vertical position of the image.
Connect the DVI output of your
computer to the HDMI 1 or HDMI 2
connector of the TV. Use a HDMI to
DVI cable if the DVI output is to be
connected.
2
3
Connect the audio cable to the PC’s
Audio jack and to the L / R Audio jacks
(EXT3) of the TV.
Press the
key to display Source
List and use the Î ï key to select
HDMI 1 or HDMI 2.
Features menu
Source list
TV
• The Features menu comprises Mode
Selection and Format features.
• When you connect PC supporting
resolutions of 480p or 720p, the Mode
Selection item will be available in the
Features menu. This will allow you to
select between the PC and HD mode.
• Format feature works exactly in the same
way as the screen formats of the TV. (see
page 39).
EXT 1
EXT 2
EXT 3
EXT 4
HDMI 1
HDMI 2
Digital TV
4
Press the Æ /
selected source.
key to switch to the
Note : When using HDMI to connect
your TV to the PC, it is possible that they
may not operate perfectly first time. Often
this is resolved by changing the resolution or
settings of the device connected to the TV. In
some situations you may see a dialogue box on
screen and need to press ”OK” to continue
watching the TV. Please refer to the user
manual of the connected device on how to
make necessary changes.
31.2
Control TV settings while a
PC is connected
1
2
Press the
menu.
key to display the main
Press the Î ï keys to select Picture,
Sound or Features and the Æ /
key to enter the selected item menu.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
32 Using the TV in HD
(High Definition) mode
The HD (High Definition) mode allows you
to enjoy clearer and sharper pictures if you
are using HD equipment that can produce
high definition video signals.
32.2
Control TV settings while in
HD mode
1
2
Press the
menu.
key to display the main
Press the Î ï keys to select Picture,
Sound or Features and the Æ /
32.1
Connecting the HD equipment
Important: For the TV to function in the
HD mode, the following steps must be taken.
key to enter the selected item menu.
3
Press the Î ï key to select the
settings and the Í Æ key to select or
adjust setting.
1
Connect the HDMI or DVI output of
your HD equipment to the HDMI 1 or
HDMI 2 connector of the TV. Use a
DVI to HDMI cable if DVI output is
connected. You can also connect the
Component Video Outputs (Y, Pb, Pr)
of the HD equipment (if any) to the
Component Video Inputs (Ext 4) of the
TV.
4
5
To return to previous menu, press the
Í key.
To exit the menu, press the
key.
Picture menu
• The Picture menu comprises Brightness,
Colour, Contrast, Sharpness, Colour
Temp., Contrast+, Horizontal Shift,
and Vertical Shift.
2
3
Connect the audio cable to the Audio
jack of the HD equipment and to the
L / R Audio jacks (EXT3) of the TV .
• Except for the Horizontal Shift and the
Vertical Shift features, all the other
functions work exactly in the same way
as the features in the TV Picture menu
(see page 37).
Press the
key to display Source
List and use the Î ï key to select
HDMI 1 or HDMI 2 (or EXT 4 if you
using YPbPr connection).
• Horizontal Shift feature allows you to
adjust horizontal position of the image.
Source list
TV
EXT 1
EXT 2
EXT 3
EXT 4
• Vertical Shift feature allows you to
HDMI 1
HDMI 2
Digital TV
adjust vertical position of the image.
Sound menu
• The Sound menu comprises Equalizer,
Balance, AVL and Incredible
Surround features and work exactly
in the same way as the TV Sound menu
(see page 37).
4
Press the Æ /
selected source.
key to switch to the
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Features menu
• The Features menu comprises Timer,
Child Lock, Parental Lock, Mode
Selection and Active Control features.
Except for Mode Selection feature, all
the other features work exactly in the
same way as the TV Sound menu (see
pages 34-36).
• When you connect HD (High Definition)
equipment supporting resolutions of 480p
or 720p, the Mode Selection feature
will be available in the Features menu. This
will allow you to select between the PC
and HD mode.
32. 3
Supported formats
HD format
480p, 480i, 576p, 576i, 720p, 1080i
1080p (applicable to 47” LCD TV only).
SD format
480i, 576i
Note
Your Philips TV is HDMI compliant. If you do
not get a good picture, please change the video
format on your device (DVD player, cable
set-top box, etc.) to a standard format. For
example, for DVD player, select 480p, 576p,
720p or 1080i.
Please note that this is not a defect of the
TV set.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
33 Connecting other
equipment
33.1 Overview of connections
Satellite
receiver
Cable
Box
VCR
DVD
Satellite
Antenna
AUDIO IN
L
Y
HDMI 1
HDMI 2
R
Pr
Pb
SERV C
EXT 4
Decoder
Satellite
receiver
Cable
Box
Decoder
DVD
Computer
Home Cinema
DVD
Home Cinema
DVD
VCR
VCR
45
Download from Www.Somanuals.com. All Manuals Search And Download.
33.2 Connect VCR or DVD recorder
With a eurocable
Connectors at
rear of TV (facing
downward)
Cable
1
1
2
Connect the aerial cables
as shown.
and
1
3
Connect the eurocable
Press the
as shown.
2
3
key on the remote
2
control display Source list.
Press the ï key repeatedly to select
4
EXT2 and press the Æ /
confirm selection.
key to
Connectors at
rear of TV (facing
backward)
33.3 Connect Decoder and VCR
Connect a eurocable to your decoder
4
Connectors at
rear of TV (facing
downward)
and to the special euroconnector of your
recorder. See also the user manual of your
recorder.
Cable
1
Warning
Do not place your recorder too close to
the screen as some recorders may be
susceptible for signals from the display.
Keep a minimum distance of 0,5 m from the
screen.
3
2
Recorder
Tip
With the aerial cable only
You can also connect your decoder directly
to EXT1 or EXT2 with a eurocable.
1
1
2
Connect the aerial cables
and
as shown.
Tune in your recorder’s test signal and
store the test signal under programme
number 0.
2
4
(See “Manual tuning of analogue
programmes”, page 30. See also the
user manual of your recorder).
Decoder
Recorder
46
Download from Www.Somanuals.com. All Manuals Search And Download.
33.4 Connect 2 VCRs or VCR and
DVD recorder
33.5 Connect a satellite receiver
With a eurocable
With eurocables
1
Connect the aerial cables
shown.
Connect your satellite receiver to
and
as
.
1
2
1
2
1
2
Connect the aerial cables
and as shown.
,
3
2
3
4
Connect your VCRs or DVD-recorder
to EXT1 and EXT2 with the euro
EXT1 or EXT2 with a eurocable
3
Press the
control to display Source list.
Press the ï key to select EXT1 or
key on the remote
4
5
cables
and
.
Press the
key on the remote
control to display Source list.
Press the ï key to select EXT1 or
3
4
EXT2 and press the Æ/
confirm selection.
key to
EXT2 and press the Æ/
key to
confirm selection.
With Component Video connectors
With the aerial cables only
See “Connect a DVD player, a satellite
receiver or a cable box”, see page 48.
1
1
2
Connect the aerial cables
,
and
as shown.
3
Tune in your recorder’s test signal and
store the test signal under programme
number 0.
(See “Manual tuning of analogue
programmes”, page 30. See also the
user manual of your recorder).
2
Connectors at
rear of TV (facing
backward)
Connectors at
rear of TV (facing
downward)
Connectors at
rear of TV (facing
backward)
1
Connectors at
rear of TV (facing
downward)
2
Cable
3
1
Satellite receiver / cable box
3
5
4
2
Recorder
Recorder
47
Download from Www.Somanuals.com. All Manuals Search And Download.
33.6 Connect a DVD player, Cable
box or game console
Press the
control to display Source list.
key on the remote
3
4
With a HDMI connector
Press the ï key to select EXT 4 and
press the Æ/
selection..
key to confirm
HDMI is the leading new standard for Digital
video and audio inter-connection.
In case of a cable box and/or a satellite
receiver also connect the cable TV
cable and/or the satellite antenna
5
1
Connect your equipment with the
HDMI connector.
3
4
cable
and the aerial cable
.
Press the
control to display Source list.
key on the remote
2
3
Connectors at rear of TV
(facing downward)
Press the ï key to select HDMI 1 or
HDMI 2 and press the Æ/
key to
confirm selection.
Connectors at rear of TV
(facing downward)
1
2
DVD
Connectors at rear of TV
(facing downward)
33.7 Connect a DVD player, a
Satellite receiver or Cable box
With Component Video Connectors
1
1
Connect the three separate component
2
1
video cables
to the YPbPr jacks on
4
the DVD player and to the Y (yellow),
Pb (blue) and Pr (red) jacks of EXT4
on the TV.
Connect the audio cable to the DVD’s
audio L and R jacks and to the L/R
3
2
Satellite receiver / cable box
2
AUDIO jack of EXT4
.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Note
Connectors
at side of TV
Connectors at rear of
TV (facing downward)
• Cables are often colour coded. Connect
red to red, white to white, etc.;
• The labels for the component video
sockets may differ depending on the DVD
player connected. Although the
abbreviations may vary, the letters B and
R stand for the blue and red component
signals, respectively, and Y indicates the
luminance signal. Refer to the DVD
player’s instructions for use for
Audio
L/R
HDMI
DVI
2
1
definitions and connection details;
• To get an optimal viewing, it is advised to
switch your equipment to the highest
possible supported display modes.
PC
PC equipped with a DVI connector
Warning
in case you notice scrolling images,
Use a DVI to HDMI cable to connect
to one of the HDMI connector of your
1
2
wrong colours or no colour, no picture, or
even combinations of these on your screen,
verify if the connections are done in the
correct way and if the resolution and the
signal standard of the connected equipment
are set in the right way. See the user manual
for your equipment.
1
TV
.
Connect the audio cable to the PC’s
AUDIO jack and to the L/R AUDIO
2
jacks of TV EXT3
.
Press the key on the remote
control to display Source list.
Press the ï key to select HDMI 1 or
3
4
HDMI 2 and press the Æ/
key
to confirm selection.
33.8 Connect a PC
Note
Supported PC resolutions
640 x 480, 60 Hz
640 x 480, 72 Hz
640 x 480, 75 Hz
640 x 480, 85 Hz
800 x 600, 60 Hz
800 x 600, 72 Hz
800 x 600, 75 Hz
800 x 600, 85 Hz
1024 x 768, 60 Hz
1024 x 768, 70 Hz
1024 x 768, 75 Hz
1024 x 768, 85 Hz
• Only digital output of the PC can be
connected via DVI to HDMI cable.
VGA connection is not supported.
• Before connecting your PC to the TV,
select your PC monitor settings to a
refresh frequency of 60 Hz.
(Applicable to LCD TV only)
1280 x 768, 60 Hz
1280 x 1024, 60 Hz
1360 x 768, 60 Hz
49
Download from Www.Somanuals.com. All Manuals Search And Download.
33.9 Connect a Camera, Camcorder,
Game console
33.9.1 Connect a Headphone
Connect your camera, camcorder or
game console.
Insert the plug into the headphone
socket as shown.
1
2
1
2
For mono equipment, connect to
The headphone impedance must be
between 8 and 4000 Ohm. The
2
3
VIDEO
and AUDIO L
(only).
For stereo equipment, connect both
headphone socket has a 3.5 mm jack.
3
AUDIO L and AUDIO R
.
S-VHS quality with an S-VHS camcorder
is obtained by connecting the S-VHS
Tip
1
cables with the S-VIDEO input
and
Press the
key on the remote
3
AUDIO L / R inputs
.
control to switch off the sound from
internal loudspeakers of the TV.
To switch on sound, press the
key again.
1
Warning: do not connect cables
2
and
at the same time. This may cause
picture distortion.
Press the
control to display Source list.
key on the remote
3
4
Press the ï key to select EXT 3 and
press the Æ/
key to confirm
selection..
Connectors at side of TV
3
Connectors at side of TV
2
1
50
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Troubleshooting
Below is a list of symptoms you may encounter with your TV. Before you call for service,
make these simple checks.
Symptom
Possible solutions
No display on screen
• Check whether power cord is properly connected into the
mains socket and to your TV. If there is still no power,
disconnect plug. Wait for 60 seconds and re-insert plug.
Switch on TV again.
• Press the
key on the remote control.
Poor reception
(snowy noise)
• Check antenna connection to the TV and to the wall antenna
socket.
• Try manually adjusting your picture (see page 30).
•
•
Have you chosen the right TV system? (see to page 30).
Press the key to check the signal strength.
No picture
• Verify if the supplied cables are connected properly (The
aerial cable to the TV, the other aerial to your recorder, the
power cables,....).
• Verify if you have selected the correct source.
• Verify if the child lock has been switched off.
No sound on
•
Check whether the correct TV system is selected (see page 30).
certain channels
No sound
• Verify if the volume is not at the minimum.
• Check that the mute (
is on, press the
) mode is not on. If mute mode
key to deactivate mute mode.
• Verify the connections between the optional equipment and
the TV.
Sound interference
• Try switching off any electrical appliances to prevent
interference, for example, hairdryer, vacuum cleaner.
Unable to understand
the selected language
on screen to operate
set in digital mode
•
Press the
key to exit menu from screen.
• Press the
key again to display menu.
• Press the key to select the second item on the menu and
the key to enter into the next menu level.
• Press the key again and use the
menu item.
key to select the fifth
• Press the key to enter into the next menu level.
• Press the Î ï keys to select correct language.
• Press the
Press the
key to confirm selection.
key to exit menu.
•
TV not responding
to remote control
• Move closer to the receiver at the front of the TV.
Check the placement of the batteries.
• Try changing the batteries.
•
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Possible solutions
No digital channels
• Contact your dealer about the Digital Video
Broadcasting Terrestrial signal availability in your country.
One or a few tiny spots on
the screen that do not
change colour along with
the video picture
• This symptom is not a problem. The liquid crystal
panel is built with very high precision technology
giving you the fine picture details. Occasionally, a
few non-active pixels may appear on the screen
as a fixed point of red, blue, green or black.
Note : this does not affect the performance
of the set.
Intermittent or flickering • Noise is displayed if the connected digital equipment such
picture in HD mode
as DVD player or Set-Top box failed. Check user
manual of the digital equipment you are connecting.
• Use a standard-compliant (high-quality) HDMI to DVI
cable.
No sound or picture but
front panel red light is on
• Press the
key on the remote control.
PC modes do not
work
• Check whether connections are correct. (see page 49).
• Check whether the source is correctly selected.
Press
button to enter Source list and select the
correct source.
• Check whether you have configured the computer to
a compatible display resolution (see page 49).
• Check graphic card setting of PC.
S-Video colour
becomes faint
• Check whether SVHS cable is properly connected.
• Press the P + key on the remote control to do a
channel up and then press the P – key to do a
channel down.
Black bar on top and
bottom of screen in
PC mode
• Change PC refresh rate to 60 Hz.
AC3 not available
• AC3 is not supported for this set. Use the
on the remote control to select an alternative audio.
key
TV antenna cannot be
powered by set
• Some TV antennas need to be powered by the set.
This set does not support such a feature.
Changing from one
channel to another
channel takes a long time
• Pay TV channels are encoded by the cable provider and
take a longer time to decode. This is normal behaviour
and no action is required.
Cannot access digital
menu
• Check whether TV is in analogue mode. If it is, press
key to switch to digital mode.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Glossary
DVI (Digital Visual Interface) : A digital interface
standard created by the Digital Display Working
Group (DDWG) to convert analog signals into
digital signals to accommodate both analog and
digital monitors.
HDMI (High-Definition Multimedia Interface) :
Provides an uncompressed, all digital audio/video
interface between the TV and any HDMI-equipped
audio/video component, such as set-top box, DVD
player and A/V receiver. HDMI supports enhanced
or high-definition video plus two-channel digital
audio.
RGB signals : These are the three video
signals, Red Green Blue, which make up the
picture. Using these signals improves picture
quality.
System : Television pictures are not broadcast
in the same way in all countries. There are
different standards: BG, DK, I, and LL’. The System
setting (page 24) is used to select these different
standards. This is not to be confused with PAL
or SECAM colour coding. PAL is used in most
countries in Europe, SECAM in France, Russia and
most African countries. The United States and
Japan use a different system called NTSC.
S-VHS signals : These are 2 separate
Y/C video signals from the S-VHS and Hi-8
recording standards. The luminance signals Y
(black and white) and chrominance signals C
(colour) are recorded separately on the tape.
This provides better picture quality than with
standard video (VHS and 8 mm) where the Y/C
signals are combined to provide only one video
signal.
MPEG (Moving Picture Experts Group) is
the nickname given to a family of International
Standards used for coding audio-visual
16:9 : Refers to the ratio between the
length and height of the screen. Wide screen
televisions have a ratio of 16/9, conventional
screen TV sets have a ratio of 4/3.
information in a digital compressed format.
MHEG (Multimedia and Hypermedia
information coding Expert Group) : provides
standards for the coded representation of
multimedia and hypermedia information objects
that are interchanged among applications
and services using a variety of media. The
objects define the structure of a multimedia
hypermedia presentation.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2006 Koninklijke Philips N.V.
All rights reserved
Document order number: 3139 125 37902
Download from Www.Somanuals.com. All Manuals Search And Download.
Hospitality Television
20/26/32HF5335D
15/20HF5234
- 1 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation of your Philips Hotel TV
1.
Introduction
This addendum has been designed to help you install programmes on this Digital TV and activating the hotel
mode.
Use this addendum in conjunction with the User Manual of this television.
Please handle the TV with care and wipe with a soft cloth to ensure your TV keeps looking new.
2.
The benefits of the Philips hotel TV
This TV is specially designed for hotels. The Philips hotel TV offers all kind of features to
Maximise the convenience for the hotel and meet the needs for the guest
ꢀ
ꢀ
Welcome message to give a friendly welcome to your guest when activating the tv
Remote control features like low battery detection and an anti-theft screw for preventing of theft for
batteries
ꢀ
ꢀ
Access to the user menu can be blocked. This prevents users (e.g. guests) from deleting or changing
program settings and/or modifying picture and sound settings. This ensures that TVs are always set up
correctly.
A switch-on volume and programme can be selected. After switching on, the TV will always start on the
specified program and volume level.
ꢀ
ꢀ
ꢀ
ꢀ
The maximum volume can be limited in order to prevent disturbance.
The television keys VOLUME +/- , PROGRAM +/- and MENU can be blocked.
Screen information can be suppressed.
Programmes can be blanked
3.
Installing the channels
Installing Digital Programs (only applicable for 20/26/32HF5335D)
Ensure the TV is in Digital mode. If it is in Analogue mode, press the A/D (Analogue/Digital) key on the
Remote Control to enter the Digital mode.
1. Press the
(Menu Digital) key on the Remote Control
2. Press the Up/Down Arrow Key to scroll to the item called INSTALLATION and press the Right Arrow
Key
3. Press the Up/Down Arrow Key to scroll to the item called SERVICE SETUP and press the Right Arrow
Key
4. Press the Up/Down Arrow Key to scroll to the item called REINSTALL ALL SERVICES and press the Right
Arrow Key
5. Press the Up/Down Arrow Key to scroll to the item called SEARCH and press OK to start the scan. The
TV will now start to scan and install all available (Digital) TV channels and Radio stations automatically.
When the scan is completed, the TV menu will indicate the number of digital services found.
6. Press the OK key again to Store all the services that have been found.
- 2 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Analogue Programs
Ensure the TV is in Analogue mode. If it is in Digital mode, press the A/D (Analogue/Digital) key on the
Remote Control to enter the Analogue mode.
1. Press the
(Menu TV) key on the Remote Control
2. Press the Up/Down Arrow Key to scroll to the item called INSTALL and press OK
3. Press the Up/Down Arrow Key to scroll to the item AUTO STORE and press OK
The TV will now start to scan and install all available (Analogue) TV channels automatically. This operation will
take a few minutes. The TV display will show the progress of the scan and the number of programmes found.
Refer to the chapter on Automatic Tuning of Analogue Programmes in the User Manual for more details. You
can also refer to the chapter on Manual Tuning of Analogue Programmes in the User Manual if a manual scan is
preferred.
4.
Activating the Hotel Mode Setup menu (BDS)
1. Switch on the television and select an analogue channel
2. On the Remote Control, press keys: [3, 1, 9, 7, 5, 3, MUTE]
3. The BDS HOTEL MODE SETUP MENU becomes visible
4. Use the cursor keys to select and change any of the following settings:
Function
Possible selections
BDS MODE
ON /OFF
SWITCH ON SETTINGS
SWITCH ON VOLUME
MAXIMUM VOLUME
SWITCH ON CHANNEL
POWER ON
DISPLAY MESSAGE
WELCOME MESSAGE
CONTROL SETTINGS
LOCAL KEYBOARD LOCK
REMOTE CONTROL LOCK
OSD DISPLAY
HIGH SECURITY MODE
AUTO SCART
MONITOR OUT
BLANK CHANNEL
STORE
0-100, LAST STATUS
0-100
USER DEFINED, LAST STATUS
ON/STANDBY/LAST STATUS
ON/OFF
LINE 1/LINE 2/CLEAR
ON/OFF/ALL
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
ON/OFF
>
5. Select “STORE” and press [CURSOR RIGHT] to save the settings and exit BDS Hotel Mode
setup. Press [MENU] to exit without saving.
6. For BDS Hotel Mode settings to take effect, you must turn the TV set Off, then back On.
BDS Hotel Mode Functions
This paragraph describes the functionality of each item in the BDS Hotel Mode Setup menu.
BDS MODE
ON
BDS Hotel Mode is ON:
ꢀ
The user menu is blocked.
ꢀ
All settings of the Hotel Mode Setup menu are in effect.
- 3 -
Download from Www.Somanuals.com. All Manuals Search And Download.
OFF
BDS Hotel Mode is OFF:
The TV operates as a normal consumer TV
ꢀ
SWITCH ON VOL
When the user switches the TV ON, it will play at the specified volume level. There are 2 options:
ꢀ
LAST STATUS Upon start-up, the TV volume will be set to the level before the TV set was
last turned off.
USER DEFINED As specified by installer
ꢀ
Remark: “SWITCH ON VOL” cannot exceed the MAXIMUM VOL level. This is the volume level with which
the Hotel Mode Setup menu was entered.
MAXIMUM VOL
The TV Volume will not exceed the selected volume level.
SWITCH ON CHANNEL
When the user switches the TV ON, it will tune to the specified channel. There are 2 options:
ꢀ
ꢀ
LAST STATUS The TV will switch on to the last channel that was shown before the TV set
was turned off
USER DEFINED Any analogue channel can be chosen to be the first channel to switch on
POWER ON
The Power On function allows the TV to enter a specific mode of operation (On or Standby) after the mains
power is activated.
ON
STANDBY
When set, the TV will always turn ON after the mains power is enabled.
When set, the TV will always turn to STANDBY after mains power is enabled
LAST STATUS When set, the TV will always turn to the last power status before the mains power was
disabled.
DISPLAY MESSAGE
ON
OFF
Enables display of the Welcome Message for 30 seconds after the TV set is turned on
Disables the display of the Welcome Message.
If OSD DISPLAY is set to OFF, then the Welcome Message is automatically disabled.
WELCOME MESSAGE
The Welcome Message function allows the TV to show a customized greeting to the hotel guest whenever the
TV is switched on. This helps to personalize the hotel experience for guests.
The Welcome Message can consist of 2 lines of text, with each line containing a maximum of 20 alphanumeric
characters. Use the Remote Control arrow keys to create the Welcome Message.
To enable the display of the Welcome Message, the DISPLAY MESSAGE option must be ON
To clear the Welcome Message from the TV’s memory, select CLEAR
LOCAL KEYBOARD LOCK
ON
OFF
ALL
The television keys VOLUME +/-, PROGRAM +/- and MENU are blocked.
The television keys VOLUME +/-, PROGRAM +/- and MENU function normally
The television keys VOLUME +/-, PROGRAM +/-, MENU and POWER are blocked.
REMOTE CONTROL LOCK
ON
OFF
Standard Remote Control keys are disabled.
All Remote Control keys will function normally.
OSD DISPLAY
ON
OFF
Normal screen information is displayed (e.g. programme information)
Screen information is suppressed.
- 4 -
Download from Www.Somanuals.com. All Manuals Search And Download.
HIGH SECURITY MODE
ON
Allows access to the BDS Hotel Mode Setup Menu via the special BDS Setup Remote only.
(RC2573/01)
OFF
Allows access to the BDS Hotel Mode Setup Menu via BDS Setup Remote or via normal Remote
Control (using special key code sequence).
AUTO SCART
The Auto Scart function enables auto-detection of AV devices that are connected to the TV’s Scart connector.
ON
OFF
Enables Auto Scart switching in BDS Hotel Mode.
Disables Auto Scart switching in BDS Hotel Mode.
MONITOR OUT
ON
OFF
Allows audio & video output from TV via relevant AV connectors (if available).
Disables both Audio & Video output from the TV (to prevent illegal copying).
BLANK CHANNEL
The Blank Channel function disables the display of video on the TV, but does not affect the audio output. This
function can be used for audio applications (example: Off-air radio transmission, music channels, and so on),
which do not necessarily require the display of video.
ON
The current programme is blanked
OFF The current programme is not blanked (normal visible; DEFAULT value)
BLANK CHANNEL can be set for every channel. Use [P+ / P-] to go through all the programmes and set the
desired status per channel. The programme number is visible in the top left corner.
Low Battery Check
This television set has a special feature which checks the battery power level of a TV Remote Control, and
indicates if the battery is low and requires changing.
(Note: The Low Battery Check function works only with certain models of Remote Controls. Please check
with the Philips sales representative if the Remote Control used with this TV supports this function)
To activate the Low Battery Check function, hold the TV Remote Control in front of the TV, and press and
hold the OK button on the Remote Control for at least 5 seconds. A message will appear on the TV screen to
indicate if the battery power level is OK, or if it is Low. If the message indicates that the battery level is low, it
is recommended to change the batteries of the Remote Control immediately.
5.
Cloning of settings
Cloning of analogue TV channels and TV settings as described in the chapter
Hotel Mode Set-up menu
For 15/20HF5234
o
o
Wireless cloning with the SmartLoader 22AV1120 or 22AV1135
Cloning off all adjustable TV settings + analogue channel table
For 20/26/32HF5335D
o
o
Wired cloning with the SmartLoader 22AV1135 using the wire packed with the SmartLoader
Cloning off all adjustable TV settings + analogue channel table (digital channel table via automatic
installation)
Instruction for cloning of settings between TVs
Philips SmartLoader (22AV1135/00)
The Philips SmartLoader is an installation tool especially designed for easy and fast installation and copying of
TV settings on Philips Institutional TV’s.
- 5 -
Download from Www.Somanuals.com. All Manuals Search And Download.
The Philips SmartLoader works in 2 modes – Wireless and Wired:
Wireless mode ---- through infrared sensor (15/20HF5234)
Switch the SmartLoader to “Wireless” mode by sliding the side-switch to the
icon on the SmartLoader
device. Point the Wireless SmartLoader to the TV’s infrared receiver (optimal distance of 5-30cm) and proceed
with the Installation procedure listed below.
Wired mode ---- using the by-packed accessory cable(s) (20/26/32HF5335D)
Switch the SmartLoader to “Wired” mode by sliding the side-switch to the
device.
icon on the SmartLoader
Examine the rear connectors of the TV set to determine if the 3-pin or 4-pin female connector wire (packed
with the Wireless SmartLoader) should be used. Plug in the correct connector wire to the corresponding
opening on the TV set (usually marked as SERV C), and then connect the RJ11 jack end of the accessory wire
to the RJ11 socket on the SmartLoader.
The Installation Procedure consists of three simple steps:
1. Choosing a Master TV
The Master TV is the TV set whose installation and configuration settings are to be copied into other TV’s (of
the same type only).
2. Programming the SmartLoader with the settings from the Master TV
Follow these steps to program the SmartLoader with the settings of the Master TV.
a) Wireless method
ꢁSet the SmartLoader to “Wireless” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
b) Wired method
ꢁConnect the SmartLoader to the TV using the appropriate accessory cable.
ꢁSet the SmartLoader to “Wired” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
The Master TV will show the following menu:
SMARTLOADER TO TV >
TV TO SMARTLOADER >
On the TV screen, highlight the menu option “TV TO SMARTLOADER”
Press the right arrow key on the SmartLoader to start the programming process
A number display (from 0~100) will be shown on screen, indicating the percentage of the programming
progress from the TV to the SmartLoader. When the programming is completed, “##” will show “100” and the
message “DONE” will appear.
TV TO SMARTLOADER ## (0-100)
The SmartLoader is programmed and can be used to install and configure other TVs.
Copying the settings of the Master TV to other TVs with the SmartLoader
Follow these steps to install and configure the settings of a Philips TV with the SmartLoader.
- 6 -
Download from Www.Somanuals.com. All Manuals Search And Download.
a) Wireless method
ꢁSet the SmartLoader to “Wireless” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
b) Wired method
ꢁConnect the SmartLoader to the TV using the appropriate accessory cable.
ꢁSet the SmartLoader to “Wired” mode using the side switch.
ꢁTurn on the TV, and while holding the SmartLoader, point it in the direction of the
TV. Press the “MENU” Key on the SmartLoader.
On the TV screen, highlight the menu option “SMARTLOADER TO TV”
Press the right arrow key on the SmartLoader to initiate the copying process
> A number display (from 0~100) will be shown on screen, indicating the percentage of the installation
progress from the SmartLoader to the TV. When the data transfer is completed, “##” will show “100” and
the message GOODBYE will appear.
SMARTLOADER TO TV ## (0-100)
>
The TV will go to Standby mode. When the TV is next powered on, it will be configured with the settings
from the Master TV, and ready for use.
Problems and Solutions:
1. The message “I2C ERROR” is displayed on the screen.
ꢁBad connection of RJ11 wire or wrong data transmission has occurred. Try again.
2. The message “WRONG VERSION” is displayed on the screen.
ꢁThe program contained in the SmartLoader has a software code incompatible with the actual TV.
Reprogram the Wireless SmartLoader from a Master TV whose software code is compatible with the
actual TV.
3. TV doesn’t respond to the SmartLoader.
ꢁCheck if the LED on the SmartLoader lights up in green when pressing any button.
If the LED is red, it means that the batteries are low and should be replaced.
ꢁBring the SmartLoader closer to the TV infrared receiver and try again.
Notes:
ꢀ Make sure that the 3 R6/AA sized batteries are placed correctly in the bottom compartment of the
SmartLoader. The LED on the SmartLoader should light up in green when pressing any button, indicating
operational batteries. When the LED shows red, the batteries need to be replaced.
ꢀ The SmartLoader can only copy the settings between 2 TVs of the same type. Once the
SmartLoader is programmed with the settings from a Master TV of a certain type or model,
then these settings can be installed on another TV of the same model only.
ꢀ The SmartLoader cannot be used to copy the (digital) channel table of a Digital TV set.
ꢀ If the SmartLoader is used with a DVB (European Digital) TV set, then the TV set must first
be switched to Analog mode.
- 7 -
Download from Www.Somanuals.com. All Manuals Search And Download.
Disposal of your old product.
Your product is designed and manufactured with high quality materials and
components, which can be recycled and reused. When this crossed-out wheeled bin
symbol is attached to a product it means the product is covered by the European
Directive 22002/96/EC. Please find out more about the separate collection system for
electrical and electronic products in your local neighborhood.
Please act according to your local rules and do not dispose of your old products with
your normal household waste. The correct disposal of your old product will help
prevent potential negative consequences for the environment and human health.
The packaging of this product is intended to be recycled. Apply to the
local authorities for correct disposal.
2007© Koninklijke Philips Electronics N.V. all rights reserved
Specifications are subject to change without notice
Trademarks are property of Koninklijke Philips Electronics N.V. or their respective owners.
- 8 -
Download from Www.Somanuals.com. All Manuals Search And Download.
|