Philips DVD Recorder CDR775 S User Manual

Audio CD Recorder

CDR775

Instructions for use

Mode d'emploi

•

Instrucciones de manejo

OPEN / CLOSE

REC

PLAY

PAUSE

AUSE

STOP

EXT

RECORD

TYPE

FINALIZE

ERASE

SOURCE

EASY JOG

STORE/

CANCEL/

DELETE

CDR

PLA

Y/PAUSE

STOP

OPEN/CLOSE

REM

REC

TIME

TRACK

TOTAL

REM

TRACK

TIME

STEP

ENTER

AUDIO CD RECORDABLE/REWRIT

ABLE

Recordable

SYNC

MANUAL

RECORD

CHANGER

DIGITAL

OPTICAL

ANALOG

PROG

A-B

ALL

SHUFFLE

REPEAT

SCAN

TRACK

AUDIO CD PLA

YBACK

CDR77X AUDIO CD RECORDER

ON / OFF

PROG

SHUFFLE

PHONES

DISPLA

SCROLL

REPEA

DJ MODE

IR SENSOR

DOUBLE SPEED

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL INFORMATION

CAUTION

USE OF CONTROLS OR ADJUSTMENTS OR

PERFORMANCE OF PROCEDURES OTHER

THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION

EXPOSURE.

TO PREVENT ELECTRIC SHOCK, MATCH

WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERTED.

ATTENTION

POUR EVITER LES CHOCS ELECTRIQUES,

INTRODUIRE LA LAME LA PLUS LARGE DE

LA FICHE DANS LA BORNE CORRESPON-

DANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

The set complies with the FCC-Rules, Part 15

and with 21 CFR 1040.1

Canada

CDN

LASER

This digital apparatus does not exceed the Class B

limits for radio noise emissions from digital apparatus

as set out in the Radio Interference Regulations of the

Canadian Department of Communications.

Type

Wave lenght

Output Power

Semiconductor laser GaAlAs

775-795 nm (at 25°C)

2,5 mW (Read)

35 mW (Write)

Beam divergence 60 degree

Cet appareil numérique n’émet pas de bruits

radioélectriques dépassant les limites applicables dans

la règlement sur le brouillage radioélectriques édicté

par le ministère des communications du Canada.

This warning label is located on the rearside and inside this laser product.

CAUTION: INVISIBLE

LASER RADIATION

NOT STARE INTO BEAM

DAN^WG^HE^ENR^O:^{PEN. DO}

INVISIBLE LASER RADIATION WHEN OPEN.

AVOID DIRECT EXPOSURE TO BEAM.

DANGER - Invisible laser radiation when open.

AVOID DIRECT EXPOSURE TO BEAM

VARO!

AVATTAESSA JA SUOJALUKITUS OHITEJTAESSA OLET

ALTTIINANAKYMATTOMAALLE LASERSATEILYLLE.ALA

KATSO SATEESEEN.

VARNING!O^OSC^YH^NS^LP^IGAR^LR^AE^SN^ERA^SR^TU^RR^ÅLK^NO^IP^NP^GLA^ND^Ä.^RB^DET^ER^NA^NK^AT^DA^EE^LJ^ÄS^RTR^ÖA^PL^PE^NN^AD

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC (U.S.A.) RULES.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS : (1) THIS DEVICE MAY NOT CAUSE HARMFUL

INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY

CAUSE UNDESIRED OPERATION.

NOTE

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can be used in accordance with the instructions, may

cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation.

If this equipment does cause harmful interference to radio

or television reception, which can be determined by

turning this equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures :

- reorient or relocate the receiving antenna.

- increase the separation between the equipment and

receiver.

- connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

- consult the dealer or an experienced radio/TV technician

for help.

IMPORTANT

THIS PRODUCT WAS FCC VERIFIED UNDER TEST CONDITIONS THAT INCLUDED USE OF SHIELDED CABLES AND

CONNECTORS BEWTEEN SYSTEM COMPONENTS. IT IS IMPORTANT THAT YOU USE SHIELDED CABLES TO REDUCE THE

POSSIBILITY OF CAUSING INTERFERENCE TO RADIOS, TELEVISION SETS AND OTHER ELECTRONIC DEVICES.

IF YOU HAVE ANY PROBLEMS CONTACT YOUR DEALER.

ANY CHANGE OR MODIFICATIONS TO THE EQUIPMENT BY THE USER NOT EXPRESSLY APPROVED BY THE

GRANTEE OR MANUFACTURER COULD VOID THE USER’S AUTHORITY TO OPERATE SUCH EQUIPMENT.

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY

CD-R PLAYER

OneYear Free Labor

OneYear Exchange Warranty on Parts

This product must be carried in for repair.

WHO IS COVERED?

You must have proof of purchase to receive warranty service. A sales

receipt or other document showing that you purchased the product

is considered proof of purchase.

BEFORE REQUESTING SERVICE...

Please check your owner’s manual or our website at

WWW.ACDR.Philips.com before requesting service. Adjustments of

the controls discussed there may save you a service call.

WHAT IS COVERED?

TO GET WARRANTY SERVICE IN U.S.A.,

PUERTO RICO OR U.S.VIRGIN

ISLANDS...

Take the product to a Philips factory service center (see enclosed

list) or authorized service center for repair.When the product has

been repaired, you must pick up the unit at the center. Centers may

keep defective parts.

Warranty coverage begins the day you buy your product. For one

year thereafter, all parts will be repaired or replaced, and labor is free.

After one year from the day of purchase, you pay for the replacement

or repair of all parts, and for all labor charges.

All parts, including repaired and replaced parts, are covered only for

the original warranty period. When the warranty on the product

expires, the warranty on all replaced and repaired parts also expires.

(In U.S.A., Puerto Rico and U.S.Virgin Islands, all implied warranties,

including implied waarranties of merchantability and fitness for a

particular purpose, are limited in duration to the duration of this

express warranty. Because some states do not allow limitations on

how long an implied warranty may last, this limitation may not apply

to you.)

WHAT IS EXCLUDED?

Your warranty does not cover:

•

labor charges for installation or setup of the product, adjustment

of customer controls on the product, and installation or repair of

antenna systems outside of the product.

•

product repair and/or part replacement because of misuse,

accident, unauthorized repair or other cause not within the

control of Philips Consumer Electronics Company.

TO GET WARRANTY SERVICE IN

CANADA...

•

reception problems caused by signal conditions or cable or

antenna systems outside the unit.

a product that requires modification or adaptation to enable it to

operate in any country other than the country for which it was

designed, manufactured, approved and/or authorized, or repair of

products damaged by these modifications.

incidental or consequential damages resulting from the product.

(Some states do not allow the exclusion of incidental or

consequential damages, so the above exclusion may not apply to

you. This includes, but is not limited to, prerecorded material,

whether copyrighted or not copyrighted.)

Take the product to a Philips consumer service center (listed below),

self-servicing dealer ar autorized service depot.

Philips Electronics Ltd.

601 Milner Avenue, Scarborough, Ontario, M1B 1M8

•

(416) 292-5161

4977 Levy Street, St. Laurent Québec, H4R 2N9

(514) 956-0120

1741 Boundary Road,Vancouver, B.C.VSM 3Y7

(604) 294-3441

a product that is used for commercial or institutional purposes

(including but not limited to rental purposes).

(In Canada, this warranty is given in lieu of all other warranties. No

other warranties are expressed or implied, including any implied

warranties of merchantability or fitness for a particular purpose.

Philips is not liable under any circumstances for any direct, indirect,

special, incidental or consequential damages, howsoever incurred,

even if notified of the possibility of such damages.)

WHERE IS SERVICE AVAILABLE?

Warranty service is available in all countries where the product is

officially distributed by Philips Consumer Electronics Company. In

countries where Philips Consumer Electronics Company does not

distribute the product, the local Philips service organization will

attempt to provide service (although there may be a delay if the

appropriate spare parts and technical manual(s) are not readily

available).

REMEMBER...

Please record the model and serial numbers found on the product

below. Also, please fill out and mail your warranty registration card

promptly. It will be easier for us to notify you if necessary.

MAKE SUREYOU KEEP...

Please keep your sales receipt or other document showing proof of

purchase. Attach it to this owner’s manual and keep both nearby.

Also keep the original box and packing material in case you need to

return your product.

MODEL #

SERIAL #

This warranty gives you specific legal rights. You may have other rights which vary from state/province to state/province.

Philips Service Company, P.O. Box 555, Jefferson City,Tennessee 37760, (800) 531-0039

EL6191E001 / MAC 6058 / 10-96

IB7922E001

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTENTS

English ....................................................7

Français.................................................35

Español .................................................63

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Table of contents

GENERAL INFORMATION AND DISCS

Welcome ......................................................................8

About this manual........................................................8

Technical data ..............................................................8

Discs for recording.......................................................9

Discs for playback........................................................9

Maintenance ................................................................9

Accessories .................................................................9

OPERATING BUTTONS AND CONNECTIONS

Operating buttons on the front..................................10

Connections at the back ............................................11

DISPLAY

DISPLAY indications...................................................11

DISPLAY messages ....................................................12

MENU messages........................................................13

INSTALLATION

Connections general ..................................................13

Analog connections CD recorder & CD player ..........14

Analog connections CD player deck..........................14

Digital coaxial connections CD recorder ...................15

Digital optical connections CD recorder....................15

Power supply..............................................................16

Setup recommendations............................................16

Inserting batteries in the remote control ..................16

REMOTE CONTROL

Remote control commands ........................................17

Inserting discs............................................................17

RECORDING

Remarks about recording...........................................18

Recording modes........................................................18

High speed recording from internal CD player..........19

Listen mode recording from internal CD player ........20

Manual recording from external CD player...............21

Autostart recording from external

CD player - CD-SYNC.................................................22

Finalizing CDR & CDRW discs ...................................23

Unfinalizing CDRW discs ...........................................23

Erasing CDRW discs ..................................................24

PLAYING

Play a 2-disc changer (Changer mode) ......................25

Playing CDs on Deck 1 and/or Deck 2 (DJ mode) .....25

Selecting a track ........................................................26

Search ........................................................................26

Shuffle (random order) play.......................................27

Repeat CD, track or program .....................................27

PROGRAMMING

Remarks about programming.....................................28

MENU MODE/CD TEXT INPUT

Remarks about Menu mode.......................................29

General operation of Menu .......................................29

A. Text input...............................................................30

B. Erasing text ...........................................................30

C. Reviewing CD Text memory..................................31

D. Auto track increment ............................................32

E. Balance..................................................................32

FIXING PROBLEMS

Troubleshooting..........................................................33

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL INFORMATION

Welcome !

Thank you for buying this Philips Compact Disc Recorder/

Player Double Deck.

In the 1980s Philips invented a new audio system - the CD.

The CD (compact disc) revealed the new dimensions of digital

sound and added to the pleasure of audio.

Compact-disc technology permits a high contrast in both loud

and soft passages, with perfect channel separation.

Philips has now further developed compact disc technology

and the result is the CD recorder.

With your Philips CD recorder/player, you can make your own

high-quality audio CDs (subject only to legal restrictions on

copying), either by recording at normal or high speed from the

Player to the Recorder, or by recording from an external

source. And naturally, you can also play all pre-recorded audio

CDs, using one or both decks individually, or together as a 2-

deck changer.

Note: In certain countries, including the UK and certain

Commonwealth countries, use of the product (or CD

Recorder) as shown or suggested in this user manual

may require the permission of copyright holders.

Technical data

About this manual

Subject to modification without notice.

This manual gives instructions for operating this CD recorder.

Please note:

General

- the digits (1) throughout the text indicate a sequence of

actions necessary to perform a certain operation;

- the arrows (➜) indicate the reaction from the recorder;

- the dots (•) indicate remarks, advice or special options

within a sequence of actions. The dot-marked instructions

are not necessary for operation.

Power consumption ..........................................................20 W

Power consumption in Standby ..........................................6 W

Operating temperature ..................................................5-35° C

Weight ..............................................................................4.5 kg

Dimensions ..................................................435 x 310 x 88 mm

Audio

Frequency response..............................................2Hz-22050 Hz

Playback S/N (A-weighted) ............................................100 dB

Playback S/N ..................................................................100 dB

Playback dynamic range CDR ..............................95 dB (90 dB)

Playback dynamic range CD..............................................90 dB

Playback total harmonic distortion CDR........88 dB = 0.0033 %

Playback total harmonic distortion CD..........85 dB = 0.0056 %

Channel separation ........................................................100 dB

Recording S/N (A-weighted) ............................................98 dB

Recording S/N digital without SRC ..................equal to source

Recording dynamic range..................................................92 dB

Recording total harmonic distortion + noise ....85 dB (0.0056%)

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL INFORMATION AND DISCS

Discs for recording

Maintenance

For recording use, special audio discs must be used (for music

only). These discs bear one of the logos as shown below. The

text 'DIGITAL AUDIO' is present!

For recording, it is very important to use discs that are free of

dust and scratches.

To clean a CD, wipe it in a straight

line from the center towards the

edge using a soft, lint-free cloth. A

cleaning agent may damage the

disc! Write only on the printed side

of a CDR or CDRW, and only with a

soft felt-tipped pen.

Your recorder can use two types of discs for recording

purposes:

- CD-Audio Recordable (CDR) discs:

fully recorded and finalized, these discs

play on all CD players and recorders.

Recordable

- CD-Audio ReWritable (CDRW) discs:

can be recorded, erased and re-recorded

hundreds of times. When finalized, they

play on CDRW compatible CD players

and recorders. In the course of 1999 most Philips CD players

and recorders will be CDRW compatible.

Clean the CD recorder with

a soft, slightly dampened lint-free

cloth. Do not use any cleaning

agents as they may have a corrosive

effect.

ReWritable

Important:

Do not expose the CD recorder

batteries or CDs to humidity, rain,

sand or excessive heat (caused by

To ensure proper working of the set, we recommend the use

of Philips audio CDR and audio CDRW discs only.

OPEN

STOP

AUDIO CD RECORDABLE/REWRIT

ABLE

heating equipment or direct

sunlight).

Discs for playback

Always keep the tray closed to avoid dust on the lens.

Your CD recorder is able to play:

The lens may cloud over when the CD recorder is suddenly

moved from cold to warm surroundings, making it impossible

to play a CD. Leave the CD recorder in the warm environment

until the moisture evaporates.

- All pre-recorded audio CDs.

- All Audio CDR and Audio CDRW.

Note: CDR(W) discs recorded with a computer can only be

used when they are correctly treated according the

audio standard (IEC958: Consumer part). Single session

only!

Accessories

- 2 Analog audio cables (with red and white plugs)

- 1 Digital coaxial cable (with black plugs)

- Power cord

- 2 Batteries

- Remote control

- Guarantee

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING BUTTONS AND CONNECTIONS

10 11 12

14 15 16 17 18 19 20 21 22

OPEN / CLOSE

REC

PLAY

AUSE

STOP

TYPE

RECORD

EXT

FINALIZE

ERASE

SOURCE

EASY JOG

CDR

STORE/

CANCEL/

DELETE

REM

REC

TIME TRACK

TOTAL

REM TRACK

TIME

STEP

11 12

13 14

ENTER

15 16

17 18

19 20

SYNC

MANUAL

RECORD

CHANGER

AUDIO CD RECORDABLE/REWRIT

ABLE

Recordable

DIGITAL

OPTICAL

ANALOG

PROG

A-B

ALL

SHUFFLE

REPEAT

SCAN

TRACK

CDR 77X

AUDIO CD RECORDER

AUDIO CD PLA

YBACK

ON / OFF

PROG

SHUFFLE

PHONES

DISPLA

SCROLL

REPEA

DJ MODE

DOUBLE SPEED

IR SENSOR

31 30 29 28 27 26 25

CDR

OUT

DIGITAL

OUT

ANALOG

OUT

DIGITAL

ANALOG

OPTICAL

Operating buttons on the front

& ¡EASY JOG ™ ........- previous/next track (Play and

CD recorder

(rotate)

Program mode)

- recording level control (recording)

- selects settings (menu on)

1 ON/OFF........................turns the CD recorder ON or OFF (if

the recorder is in Standby mode,

pressing any key will activate the

CD recorder)

ENTER..........................- plays selected tracks

(push) - selects settings in Menu mode

- programs track numbers

2 Standby indicator

3 Disc tray

4 OPEN/CLOSE /..........opens/closes disc tray

5 PLAY/PAUSE 2; ......starts play/interrupts play or

recording

6 STOP 9........................stops/clears a program

7 REC(ord) TYPE ............selects recording modes

8 RECORD ......................starts recording, finalizing, erasing

9 FINALIZE ....................selects finalize mode

0 ERASE..........................selects erasing mode (disc or track)

! EXT SOURCE ..............selects input source

@ CDR ............................selects CD recorder deck

display/keys

* STORE/MENU ............- stores Menu settings

- enters Menu mode

( CANCEL/DELETE ......- deletes tracks from a program

- deletes text in Menu mode

- returns to a higher level in the

≤ IR sensor ....................receives signals from the remote

control

∞ PHONES......................socket for headphones

§ DJ MODE ....................separate play of CD recorder deck

and CD player deck

≥ REPEAT........................repeats play (All, program or track)

• SCROLL........................activates scrolling of text over the

display (once)

CD player

$ CD ..............................selects CD player deck display/keys

) PLAY/PAUSE 2; ......starts play/interrupts play

¡ STOP 9........................stops/clears a program

™ OPEN/CLOSE /..........opens/closes disc tray

£ Disc tray

ª DISPLAY......................selects display information,

permanent text scrolling and time

º SHUFFLE......................plays CD(RW) or program in

random order

⁄ PROG(ram) ..................opens/closes program memory

General

Note: Unless stated otherwise, all controls are on the front of

the CD recorder. If the corresponding keys are also

provided on the remote control, you can use these after

selecting the CD recorder deck or CD player deck by

pressing CDR or CD.

# Display..........................information screen

% Q ............................- searches backward

- cursor control in Menu/Prog.

review mode

^ R ............................- searches forward

- cursor control in Menu/Prog.

review mode

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATING BUTTONS AND CONNECTIONS

DISPLAY

Connections at the back

DISPLAY indications

1 Connection to power supply

2 ANALOG OUT ............connects CD player deck to the

line input of an amplifier (left and

right)

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17 18 19 20

SYNC MANUAL

3 DIGITAL OUT CD ......connects CD player deck to the

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

digital coaxial input of e.g.

amplifier or recording device

4 ANALOG IN ................connects to the line output of an

23 22 21 20 19 18 17 16

15 14 13 12 11

amplifier (left and right)

5 ANALOG OUT CDR & CD

......................................connects to the line input of an

amplifier (left and right)

1 REM/REC TIME ..........remaining time/remaining

recording time/recording time

6 DIGITAL IN..................connects to the digital coaxial

output of an external CD player

7 DIGITAL OUT CDR & CD

2 TRACK ........................track number

..............................balance (lights up during balance

adjustment)

......................................connects to the digital coaxial

input of amplifier or recording

4 TOTAL REM

TRACK TIME ..............indicates total or remaining time

of disc or track

device

8 OPTICAL IN ................connects to the digital optical

5 }................................remote control active

6 STEP ............................indicates the number of tracks in a

program

output of an external CD player

7 Track bar ....................indicates:

- tracks on a disc or in a program

- track in play

8 + 20 ..............................disc or program contains more

than 20 tracks

9 PROG(ram) ..................flashes during programming/lights

in program mode

0 REPEAT TRACK/ALL..lights up when a track/complete

disc (or program) is repeated

! SCAN ..........................lights up when the first 10

seconds of each track are played

@ SHUFFLE......................plays tracks in random order

# s ..............................CD player deck selected

$ c..............................CD inserted (a pre-recorded CD or

finalized CDR or CDR(W) disc)

% fRECORDg ............lights during recording from the

internal CD

^ L/R ; ;........................record/play level bar, indicates the

audio signal level

& j k........................DJ mode selected

* iCHANGERh ........changer mode selected

( ;....................................pause function active

) B ................................lights during play

¡ R(W) ............................unfinalized CDR(W) disc inserted

™ 0..................................lights during recording

£ ANALOG......................- analog input selected for

external recording

......................................- analog recording

≤ OPTICAL I ..................optical input I selected for external

recording

∞ DIGITAL I ....................digital input I selected for external

recording

§ SYNC ..........................synchronized recording active

≥ MANUAL ....................manual recording active

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY

XX XX FINAL................time countdown when finalizing a

disc

DISPLAY messages

PRESS RECORD............to start manual recording,

finalizing or erasing

START SOURCE............to start synchronized recording

from a source (e.g. CD player)

FINALIZED CD............when trying to record on a

finalized CDR or a prerecorded CD

UNFINALIZE/ ................when trying to record on a

PRESS ENTER ..............finalized CDRW

PROF SOURCE ..............when a professional source is

connected

REC TEXT ......................when reading CD text from source

disc for recording

TEXT PROTECT............when CD text of source disc is

subjected to copy protection (CD

Messages as listed and explained here may appear on the

display for your guidance.

General

READING..........................reading disc information

OPEN..................................opening tray

CLOSE ..............................closing tray

NO DISC..........................no disc inserted, disc unreadable

or disc inserted upside down

PROG FULL....................program full

INSERT DISC ..............insert disc or insert disc correctly

WRONG DISC..................inserted disc is not an audio CD

UNFINALIZED ..............unfinalized CDR(W) disc

MEMORY XX% ............indicates the amount of memory

used for unfinalized discs

text will not be recorded)

Play

Recording

CHANGER MODE............CD changer-mode selected

DJ-MODE..........................DJ- mode selected when recording

keys are pressed in DJ-mode

WAIT..................................- when STOP 9is pressed during

recording

- when STOP 9is pressed during

PROGRAM..........................program mode selected

ALBUM TITLE ..............will be followed by album title

TRACK TITLE ..............will be followed by track title

ALBUM ARTIST............will be followed by artist's name

TRACK ARTIST............will be followed by track artist's

name

recording the first 4 seconds of a

track

UPDATE ..........................updating disc contents

DISC FULL....................recording no longer possible

DIGITAL 1....................digital coaxial input 1 selected

OPTICAL ........................digital optical input selected

ANALOG............................analog input selected

COPY PROTECT............no digital recording can be made

from the connected source

Others

NO AUDIO TR................when the recorder enters a data

track during recording

FINALIZE CD ..............laser power calibration performed

96 times, finalize disc needed

INITIALIZING............during laser power calibration for

unfinalized discs

DISC RECOVER............during disc recovery after power

failure

NOTFINALIZED............when opening the tray with an

unfinalized disc inserted (CD

recorder)

RECORD FAST ..............high-Speed recording selected

REC LISTEN..................listen Speed recording selected

MAKE CD..........................high-speed recording of a

complete disc and Auto Finalize

function selected

REC EXT DISC ............synchronised start of recording

from external source selected

REC EXT MAN................manual start of recording from

external source selected

_XX DB............................level is being adjusted

DOES NOT FIT ............time left on CDR(W) disc is not

enough for proposed recording

ANALOG REC..................copy prohibited track found during

recording. Track will be copied

OPC ERROR....................OPC failure during OPC procedure

(OPC = Optimum Power

Calibration)

RECORD ERROR............recording error in menu mode

DISC ERROR..................when trying to record on or finalize

a recovered disc

MEMORY FULL/..............when no more text can be stored

FINALIZE CD ..............for a certain disc. Another disc

must be finalized to obtain

memory space

NOT POSSIBLE............when trying to erase a CDR

analog (Copy Protection Regulations)

ERASE TRACK ..............when erasing one or more tracks

ERASE DISC..................when erasing a disc

FINALIZE CD ..............when finalizing a disc

FINALIZED....................when trying to finalize an already

finalized disc

CHECK INPUT ..............when RECORD is pressed while no

digital source is detected

XX XX ERASE................time countdown when erasing a

track or a disc

Download from Www.Somanuals.com. All Manuals Search And Download.

DISPLAY

INSTALLATION

MENU messages - See Menu mode

Connections general

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

For playback on the CD recorder (and/or CD player deck) the

following outputs are present:

- Digital coaxial output (CD & CDR);

- Analog output (CD & CDR).

EASY JOG

STORE/

CANCEL/

DELETE

SYNC MANUAL

RECORD

PROG

ENTER

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

We advise you to connect these to the TAPE or CDR input on

your amplifier.

Menu messages

NO TRACKS....................when attempting to edit text for a

disc which has no tracks

TEXT EDIT....................when entering Text Edit mode

ALBUM ARTIST............when editing or erasing an artist's

name

For external recording the following inputs are present:

- Digital optical input;

- Digital coaxial input;

- Analog input.

ALBUM TITLE ..............when editing or erasing a title

ARTIST TR N................when editing or erasing an artist's

name per track

TITLE TR N..................when editing or erasing a title per

track

TEXT ERASE..................when entering Text Erase mode

ALL TEXT ......................when entering All Text mode

ERASE OK ......................when confirmation for erasing

must be given with ENTER key

ERASE ALL OK ............when confirmation for erasing

must be given with ENTER key

For playback of CD player deck separately (DJ mode) from the

CD recorder the following outputs are present:

- Digital coaxial output (CD);

- Analog output (CD).

We advise you to connect these to the CD input on your

amplifier.

The connections you make will depend upon the possibilities

your audio equipment offers. Please refer to the user manuals

for your other audio equipment first.

ERASE MEMORY............when waiting for confirmation for

erasing a disc

MEMORY VIEW ..............when selecting text review per

unfinalized disc in memory

MEMORY EMPTY............when REVIEW is selected while no

text is in memory

AUTO TRACK..................when selecting auto track

increment ON or OFF

ON ......................................auto Track increment on

OFF....................................auto Track increment off

SET BALANCE ..............when selecting BALANCE

NO TEXT..........................no text stored for disc

Digital recordings (optical or coaxial) give the best

performance in audio and usability (e.g. auto-track).

(The digital optical connection is less sensitive to external

disturbances).

If your equipment does not offer digital connections, the high

quality Analog-Digital-Converter of your CD recorder will

ensure good audio performance when recordings are made

from the analog input.

Playback via the digital coaxial output of the CD recorder

gives the best audio performance.

If your equipment does not offer digital connections, the high

quality Digital-Analog-Converter of the CD recorder ensures a

good sound quality via the analog output.

We advise you to always establish both digital and analog

connections. This will mean that analog recordings can

always be made when digital recording is not possible.

We have described the most common ways of connecting the

CD recorder. If you still have difficulties with the connections,

please contact the Philips Consumer Service desk in your

area.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Analog connections CD recorder & CD player

Analog connections CD player deck

This connection must be made for playback on the CD

recorder deck as well as the CD player deck (cable 2).

Cable 1 is only required if you want to make recordings from

an external analog source.

This connection is only required if you want to playback on

the CD player deck seperately from the CD recorder deck. This

will be the case in DJ-mode.

Use the audio cables supplied. Connect the red plugs to the

R sockets, and the white plugs to the L sockets.

1 For separate playback on the CD player deck, connect a

third cable 3 (not supplied) between the ANALOG OUT

sockets of the CD recorder and the input sockets of an

amplifier e.g. CD, or AUX.

(Connect the red plugs to the R sockets, and the white plugs

to the L socket.)

1 For recording, connect cable 1 between the ANALOG IN-

sockets on the CD recorder and the CDR LINE- or TAPE OUT-

sockets of an amplifier.

Note: For recording directly from a CD player, the analog

input of the CD recorder should be connected to the

analog output of the CD player.

Note:

- Never use the PHONO input.

- Your CD recorder/player is equipped with a digital coaxial

output for the CD player deck. This output can be used for

digital playback.

2 For playback, connect cable 2 between the ANALOG OUT

sockets on the CD recorder and the input sockets of an

amplifier e.g. TAPE IN, CDR or AUX.

Note: Never use the PHONO input.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Digital coaxial connections CD recorder

Digital optical connections CD recorder

This connection is only required if you want to make

recordings from an external CD player with a digital coaxial

output.

This connection is only required if you want to make

recordings from an external CD player with a digital optical

output.

Use the digital coaxial cable supplied.

1 For external recording, connect the cable 4 between the

DIGITAL IN-socket on the CD recorder and the DIGITAL OUT-

socket of an external CD player.

When connecting the Digital

Optical cable, make sure it

is fully inserted until

there is a click.

Note: Your CD recorder is equipped with a digital coaxial

output (common output for CD recorder & CD player

deck). This output can be used for digital playback.

1 Remove the dust caps from the digital optical connection.

(We recommend you save the cap.)

2 For external recording, connect a fibre-optic cable 5

between the digital optical input of the CD recorder and the

digital-optical output of an external CD player.

Note: For playback, the digital coaxial outputs or analog

outputs of the CD Player and CD recorder should be

connected to an amplifier.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Power supply

Inserting batteries in the remote control

1 Plug the power cord supplied into the POWER SUPPLY

connector on the CD recorder, then into a wall socket.

2 Press ON/OFF.

➜ The CD recorder will switch on.

1 Open the battery compartment cover.

Note:

2 Insert 2 batteries (“AA”, LR-6 or UM-3; as supplied) as

shown.

- If the CD recorder is in Standby mode (red LED on), press

any key to activate the recorder.

- The CD recorder will automatically adjust to the local mains

voltage.

- When the CD recorder is in the “OFF” position, it is still

consuming some power. If you wish to disconnect your CD

recorder completely from the mains, withdraw the plug from

the AC Outlet.

3 Replace the cover.

Note: We recommend that you use 2 batteries of the same

type and condition.

Batteries contain chemical substances; they should be

disposed of properly.

Setup recommendations

- Place the CD recorder on a solid, vibration-free surface.

- Do not place the CD recorder near a source of heat or in

direct sunlight.

- Do not use the CD recorder under extremely damp

conditions.

- If the CD recorder is placed in a cabinet, make sure that a

one-inch space remains free on all sides of the CD recorder

for proper ventilation.

Important:

- Do not put the CD recorder on top of other equipment that

will heat up the CD recorder (e.g. receiver or amplifier).

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOTE CONTROL

Remote control commands

Inserting discs

SCAN

ABC

SHUFFLE

DEF

REPEAT

GHI

JKL

OPQ

OPEN/CLOSE

PLA

Y/P

AUSE

RST

UVW

XYZ

STOP

REC

TYPE

RECORD

FINALIZE

EXT

ERASE

SPACE

SCROLL

SOURCE

TRACK INCR.

CDR

ON/OFF

DIRECT LINE

RECORDING

;

DOUBLE SPEED

MENU/

STORE

PROG.

ENTER CANCEL

1 Press OPEN/CLOSE to open the disc tray.

➜ OPENlights up.

2 Insert a CD, CDR or CDRW in the appropriate recess in the

tray, label side up.

STANDBY ....................switches to Standby/On

SCAN ................................plays the first 10 seconds of each

track

3 Press OPEN/CLOSE to close the tray (see also Playing a CD).

➜ CLOSElights up, followed by READINGthe display

will show the type of disc that has been inserted.

SHUFFLE............................plays CD(RW) or program in

random order

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

REPEAT..............................repeat play

Number/alphabet keys 0 - 9

SYNC MANUAL

RECORD

PROG

......................................- selects a track by number

- selects character for text input

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

TRACK INCR(ement) ........increases track numbers during

recording

• If a blank or partly-recorded CDR or unfinalized CDRW is

inserted, the CD recorder will calibrate the disc for optimum

recording. During this process the display will first show

INITIALIZINGand then the number of audio tracks.

Calibration can take up to 25 seconds.

SPACE................................inserts a character space during

text input

SCROLL..............................activates scrolling of text over the

display

CDR ....................................selects CD recorder deck

CD ......................................selects CD player deck

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

......................................starts CD(RW) play

SYNC MANUAL

RECORD

PROG

O ......................................- previous track (Play and Program

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

mode)

- cursor control in Menu/Prog.

review mode

SCAN TRACK

• If a CDR(W) is finalized, CD will show on the display.

P ......................................- next track (Play and Program

mode)

• If CD-text is available the TITLE/ARTIST will scroll by.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

- cursor control in Menu/Prog.

review mode

......................................stops CD(RW) and clears a program

10 11 12 13 14 15

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

Q....................................searches backward

R....................................searches forward

CHANGER

DIGITAL

OPTICAL

ANALOG

;

......................................interrupts CD(RW) play/recording

Note:

MENU/STORE ..................- enters Menu mode

- Only Audio CDs will be accepted. If a non-audio disc is

inserted, the display will show WRONG DISC/USE

AUDIO CD.

- Reading an unfinalized disc in the CD recorder deck could

take approximately 1 minute.

- For recording it is important that the blank disc is

completely free from dust particles or scratches. (See

maintenance).

- stores Menu settings

PROG.(ram) ........................opens/closes program memory

ENTER................................- selects settings in Menu mode

- programs track numbers

- starts playback of selected track

CANCEL ............................- deletes tracks from a program

- deletes text in Menu mode

- returns to a higher level in the

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Remarks about recording

Recording modes

You will soon discover how easy it is to make your own CDs.

Nevertheless, it is advisable to use a CDRW disc for your first try.

The following will be explained:

Your recorder offers several recording modes.

For recording from internal CD-deck:

- Recording from an internal CD player deck: high-speed or

listen mode.

- Recording from an external CD player deck: synchronized

start with CD player or manual start (analog or digital).

- RECORD FAST (high-speed digital recording) - fast recording

of a disc or programmed tracks.

- REC LISTEN (normal-speed digital recording) - listening to a

recording while making it.

- MAKE CD (high-speed digital recording and auto-finalize) -

fast recording of a disc or programmed tracks. Recording

will be finalized automatically.

•If the disc is a CDRW and is already finalized, you must

unfinalize it first.

•The recording procedure is the same for CDRs and CDRWs.

Warning: No more recording possible after finalizing CDR

•If the disc already contains recordings, the CD recorder will

automatically search for the end of the last track, so that

recording can start from there.

disc!

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

•CD text can be added to a recording in Stop mode and

during recording.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

•CD text cannot be recorded from an external CD player.

(Text information is not available on the output of the CD

player.)

For recording from external sources:

•The CD recorder deck is able to record CD text from the

internal CD player deck (if not subjected to copy protection).

This may take up to 2 minutes.

- REC EXT DISC (automatic start of recording) - to make an

automatic recording of an external source simply by starting

the source.

- REC EXT MAN (manual start of recording) - to start a manual

recording from an external source.

•There must be at least 7 seconds of recording time left on

the disc, otherwise you will not be able to enter record

standby mode. DOES NOT FITwill then show on the

display.

Some remarks on recording:

•If the display indicates COPY PROTECTno digital

recording can be made of the source material. Recording

will not start.

- During high speed recording, the original recording quality

will be maintained.

- When Auto track is on (default setting), track numbers will

automatically be increased during recording.

- By programming tracks first, a compilation can be recorded.

- If a finalized CD recordable disc is inserted in the CD

recorder, FINALIZED CDwill be displayed when REC

TYPE is pressed. Recording will not be possible.

- If a finalized CD rewritable disc is inserted in the CD

recorder, UNFINALIZEand PRESS ENTERwill be

displayed when the REC TYPE is pressed. If ENTER is

pressed, the disc will be unfinalized.

•The Serial Copy Management System (SCMS) only

allows digital recording under specific conditions:

- This means that it is not possible to make a digital copy

from a digital copy.

- Analog recording is always possible !

- The number of recordings to be made from the original is

unlimited.

•A maximum of 99 tracks can be recorded on a disc.

Minimum allowable track length is 4 seconds.

•Recordings from DAT or DCC players will not always stop

automatically.

Note: If during recording ANALOG RECappears, the track

will be recorded as analog, at normal speed. All other

tracks will be copied normally (at double speed).

Important:

If you want to play the recorded CDR disc on a regular

CD player, it must be finalized. See finalizing discs.

Finalized CDRW discs play only on CDRW compatible

CD players.

For recording from CD changers always use REC EXT

DISC.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

• If DOES NOT FITappears on the display, there is not

enough recording space left on the CDR(W) disc.

You can press RECORD: only complete tracks that still fit on

the CDR(W) will be recorded

High speed recording from internal CD player

EASY JOG

STORE/

CANCEL/

DELETE

ENTER

You can press PROG to select one or more tracks for

recording (see programming):

OPEN / CLOSE

REC

PLAY

AUSE

STOP

- rotate the EASY JOG/ENTER key to the required track

number, then press the key (or ENTER on the remote

control)

RECORD

EXT

TYPE

FINALIZE

ERASE

SOURCE

CDR

ANALOG

- directly select the track number via the 10-keypad on the

remote control, then press the ENTER key to confirm your

selection and go to the next step.

CDR 77X

AUDIO CD RECORDER

PROG

SHUFFLE

PHONES

DISPLA

DJ MODE

SCROLL

REPEA

Start high speed recording

During high speed recording the sound is not audible.

1 To start recording press RECORD.

Preparing for high speed recording

➜ WAITlights up. The display shows the total remaining

time for the selected recording. High-speed recording

starts. fRECORD glights up continuously.

1 Make sure that the recording disc is absolutely free of

scratches and dust particles.

•To check the track number and track time, press DISPLAY.

This can be done during recording.

2 To choose the type of recording, press REC TYPE:

once: to select ‘RECORD FAST’ if you wish to make a

fast recording of a disc or programmed tracks;

three times: to select ‘MAKE CD’ if you wish to make a

fast recording of a disc or programmed tracks

and to automatically finalize the recording. Also

see ‘Finalizing CDR & CDRW discs’.

•Recording will stop automatically.

Note: Copy prohibited tracks will be copied analog. ANALOG

RECis displayed.

➜ The display first shows the selection.

2 To stop recording manually, press STOP.

The fRECORD glabel starts blinking. After 3

seconds the display shows the remaining CDR(W)

recording time on the left and total time of source on the

right. (every 2 seconds PRESS RECORDis displayed.)

The left-hand selection indicator is lit up.

➜ UPDATElights up, fRECORD ggoes out and

recording stops. (Minimal track length must be 4 seconds

otherwise silence will be added to the track.)

•If STOP was pressed within 3 seconds after RECORD, no

recording will take place.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

SYNC MANUAL

RECORD

PROG

After recording, the display shows UPDATEfor several

seconds. The Total time indications can differ slightly.

However, no music information is lost.

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

Note: In this Recording mode, the Pause function is not

operative.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

Important:

If you want to play the recorded CDR disc on any

regular CD player, it must first be finalized. See

finalizing discs.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

SYNC MANUAL

RECORD

PROG

Finalized CDRW discs play only on CDRW compatible

CD players.

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Listen mode recording from internal CD player

- directly select the track number via the 10-keypad on the

remote control, then press the ENTER key to confirm your

selection and go to the next step.

EASY JOG

STORE/

CANCEL/

DELETE

ENTER

3 Play the source first to set the optimal recording level on

the CD recorder.

OPEN / CLOSE

REC

PLAY

AUSE

STOP

RECORD

EXT

TYPE

FINALIZE

ERASE

SOURCE

CDR

4 Rotate the EASY JOG/ENTER key until, on the Record/Play

Level bar, all the blue segments are lit up, but the red

segments do not light up continuously during the loudest

passages.

ANALOG

CDR 77X

AUDIO CD RECORDER

➜ Display shows -XX DB(Decibel, e.g. -3DB).

PROG

SHUFFLE

PHONES

DISPLA

DJ MODE

SCROLL

REPEA

5 Stop the source.

During Listen mode recording you listen to the recording

while you are making it.

Start Listen mode recording

1 To start recording, press RECORD.

Preparing for Listen mode recording

➜ WAITlights up. fRECORD glights up continuously

and the selected track or program is copied at normal

speed. The track number and the recording time left will

appear.

1 Make sure that the recording disc is absolutely free of

scratches and dust particles.

2 For recording, press REC TYPE twice:

•To check the track time, press DISPLAY. This can be done

during recording.

➜ the display first shows the selection.

The fRECORD glabel starts blinking. After 3 seconds

the display shows the remaining CDR(W) recording time

on the left and total time of source on the right. (every

2 seconds PRESS RECORDis displayed) The left-hand

selection indicator is lit up.

•Recording will stop automatically.

Note: Copy prohibited tracks will be copied analog. ANALOG

RECis displayed.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

2 To stop recording, press STOP.

SYNC MANUAL

RECORD

PROG

➜ UPDATElights up, fRECORD ggoes out and

recording stops. (Minimal track length must be 4 seconds

otherwise silence will be added to the track.)

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

•If STOP was pressed within 3 seconds after RECORD, no

recording will take place.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

After recording, the display shows UPDATEfor several

seconds. The Total time indications can differ slightly.

However, no music information is lost.

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

Note: In this recording mode, the Pause function is not

operative.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

Important:

If you want to play the recorded CDR disc on any

regular CD player, it must first be finalized. See

finalizing discs.

• If DOES NOT FITappears on the display, there is not

enough recording space left on the CDR(W) disc.

You can press RECORD: only complete tracks that still fit on

the CDR(W) will be recorded.

Finalized CDRW discs play only on CDRW compatible

CD players.

You can press PROG to select one or more tracks for

recording (see programming):

- rotate the EASY JOG/ENTER key to the required track

number, then press the key (or ENTER on the remote

control)

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

➜ MANUAL will start to flash and the display will show

REC EXT MANfollowed by WAIT. After a few

seconds, PRESS RECORDfollowed by the remaining

time and track number will appear on the display.

Manual recording from external CD player

EASY JOG

STORE/

CANCEL/

DELETE

ENTER

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

OPEN / CLOSE

REC

PLAY

AUSE

STOP

RECORD

EXT

TYPE

FINALIZE

ERASE

SYNC MANUAL

SOURCE

RECORD

PROG

SHUFFLE ALL

CDR

4 Play the source first to set the optimal recording level on

the CD recorder.

ANALOG

CDR 77X

AUDIO CD RECORDER

5 Rotate the EASY JOG/ENTER key until all the blue

segments are lighted on the Record/Play Level bar but the

red segments do not light continuously during the loudest

passages.

PROG

SHUFFLE

PHONES

DISPLA

DJ MODE

SCROLL

REPEA

Important:

➜ Display shows -XX DB(Decibel, e.g. -3DB).

- Recording from CD-changers should always be started in the

Auto-Start mode.

- Only make analog recordings when digital recording is not

possible.

6 Stop the source.

Start recording

1 To start recording, press RECORD on the CD recorder and

Preparing for manual recording

immediately start the source (from Pause or Stop mode).

➜ dwill light up continuously. The track number and

recording time left will appear on the display.

1 Make sure the disc is absolutely free of scratches and dust

particles.

2 Press EXT(ernal) SOURCE repeatedly until (depending on the

connection used):

•If CHECKINPUTmessage also flashes, the digital

connection is incorrect.

➜ DIGITAL I, OPTICAL I or ANALOG lights up and

DIGITAL 1, OPTICALor ANALOGwill appear on

the display.

•To record a 3-second silence at the start of a track, press

PAUSE on the CD recorder before starting the source.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

•To check the total remaining recording time, press DISPLAY on

the CD recorder. (This can also be done during the recording.)

SYNC MANUAL

DIGITAL

RECORD

PROG

SHUFFLE ALL

CHANGER

2 To stop recording, press STOP on the CD recorder.

➜ UPDATElights up and dgoes out.

•When Auto Track is On (default setting), track numbers will

automatically be increased during recording.

•If STOP is pressed within 3 seconds after RECORD, no

recording will take place.

•To switch off the Auto Track function, you must enter

Menu mode.

If you wish to increase track numbers manually, press

TRACK INCR(ement) on the remote control. For further

instructions see Menu mode.

•To interrupt recording, press PAUSE on the CD recorder.

dwill start to flash. Press PAUSE again to restart

recording. (A new track will always be made.)

After recording the display will show UPDATEfor several

ON (auto): The track increments are automatically taken over

from the digital source material or after 2.7 seconds of

silence during analog recording.

seconds.

Note: With AUTO TRACKON, the recorder will stop and go

to REC STANDBY for 1 minute and then goes to stop

mode automatically. Recordings from DAT, DCC or

recordings made analogously will stop after 20 seconds

of silence. With AUTO TRACK OFF, the auto stop

mode is disabled.

OFF (manual): While recording, track numbers can be

incremented manually by pressing TRACK INCR(ement)

on the remote control. (Minimum track length is 4 sec.)

(This can also be done in Auto track on mode.)

•Track numbers cannot be changed after recording.

Important:

If you want to play the recorded CDR disc on a regular

CD player, it must be finalized. See finalizing discs .

Note: Auto track works only with Consumer Sources with a

digital output signal according to the IEC 958

(consumer part) audio standard.

Finalized CDRW discs play only on CDRW compatible

CD players.

3 With the recorder stopped, press REC TYPE five times to

For recording from CD changers always use REC EXT

DISC.

enter the Manual Record standby mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

Start recording

Autostart recording from external CD player

CD-SYNC

1 To start recording, press PLAY on the selected source.

➜ The CD recorder automatically starts to record and d

lights up continuously. The track number and track time

will appear on the display.

OPEN / CLOSE

REC

PLAY

AUSE

STOP

RECORD

EXT

TYPE

FINALIZE

ERASE

SOURCE

CDR

•If, however, you start the source during a track, CD-SYNC

recording starts at the beginning of the next track or after

2.7 seconds of silence in analog recordings.

ANALOG

CDR 77X

AUDIO CD RECORDER

PROG

SHUFFLE

PHONES

DISPLA

DJ MODE

SCROLL

REPEA

•To check the remaining recording time on the CDR(W), press

DISPLAY. (This can also be done during recording.)

•The EASY JOG/ENTER key can be used to adjust the

recording level.

The CD-SYNC feature enables you to make fast and easy

recordings of a CD. Track increments are automatically detected

from the source material. Track increments cannot be added

manually. In analog source material a silence of 2.7 seconds or

more is automatically detected as a track increment.

•The recorder stops automatically.

2 To stop recording manually, press STOP on the CD recorder.

➜ UPDATElights up and SYNC and dgo out.

Preparing for autostart recording

•If STOP 9is pressed within 3 seconds after pressing PLAY,

no recording will take place.

1 Make sure the disc is absolutely free of scratches and dust

particles.

•To interrupt recording, press PAUSE on the CD recorder.

➜ dstarts to flash. (Autostart recording is disabled.) To

resume, press RECORD on the CD recorder.

2 Press EXT(ernal) SOURCE repeatedly until (depending on the

digital connection used):

➜ DIGITAL I, OPTICAL I or ANALOG lights up and

DIGITAL 1, OPTICALor ANALOGwill appear on

the display.

After recording the display will show UPDATEfor several

seconds.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

Note:

- Recordings from DAT, DCC or analog sources will only stop

after 20 seconds of silence.

- Auto track is always active.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

Important:

If you want to play the recorded CDR disc on a regular

CD player, it must be finalized. See finalizing discs.

3 With the CD recorder stopped, press REC TYPE four times

if you wish to record a complete disc or program.

Finalized CDRW discs play only on CDRW compatible

CD players.

➜ dand SYNC will start to flash and the display will show

REC EXT DISCand WAITfollowed by the track

number, the total remaining time and START SOURCE.

For recording from CD changers always use REC EXT

DISC.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

•If input label (DIGITAL I) flashes, the digital connection is

incorrect.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING

Finalizing CDR & CDRW discs

Unfinalizing CDRW discs

During finalizing, the Table of Contents (TOC) is written to the

disc.

For CDRW discs only.

If you want to make more recordings (or erasures of tracks) on a

finalized disc, you must unfinalize it first. The Table of Contents

(TOC) will be removed. (This is not possible for CDR discs.)

To unfinalize:

Finalizing is a simple procedure that is necessary in order to:

- be able to play recordings on a CD PLAYER,

- avoid further unwanted recordings on a disc,

- avoid erasure of tracks on a CDRW,

1 With the CD recorder stopped, press REC TYPE or ERASE.

➜ UNFINALIZE and PRESS ENTERwill appear on

the display.

- write CD text on a CDR(W).

Auto finalizing

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

Auto finalizing is possible when using the MAKE CD

recording function.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

Manual finalizing

1 Make sure the disc (in the CD recorder) is absolutely free of

scratches and dust particles.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

2 With the recorder stopped, press FINALIZE.

➜ The display will show FINALIZE CDand PRESS

RECORD.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

2 Press JOG (ENTER).

➜ The disc will now be unfinalized and can be recorded on

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

again and the recording or erasure mode is entered.

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

3 You can now start recording or erasing. If no further

recording or erasure is required, press STOP 9.

3 Press RECORD.

➜ XX XX FINALand the approximate finalization time

is shown on the display.

Note:

- Unfinalizing will take approximately 1 minute 30 seconds.

- When unfinalizing a CDRW disc with text available on it,

this text will be transferred to the CD recorder memory. The

text memory may be full. If so, the message MEMORY

FULL/FINALIZE CDwill be displayed.

To empty the recorder’s text memory, you will have to erase

text from it. This can be done in two ways:

1) Finalize one or more unfinalized discs for which CD text is

available.

The display counts down through the finalization.

Upon completion, the total number of tracks and the

total time recorded will appear on the display.

^{For CDR(W),}r^{changes to}d^{on display.}

Finalizing will take at least 2- 4 minutes.

Note:

- During finalization, the CD recorder will not accept

operating commands.

- When a CDR has been finalized, no more recordings can be

added.

2) Delete text of unfinalized discs with the ‘memory view’

option in the Menu mode.

Download from Www.Somanuals.com. All Manuals Search And Download.

RECORDING

To erase the entire disc:

Erasing CDRW discs

1 Press ERASE twice.

EASY JOG

➜ The display will show the number of tracks and their

total playing time. ERASE DISCand PRESS

RECORDwill light up.

STORE/

CANCEL/

DELETE

ENTER

•If the disc is finalized, CD will appear on the display after

inserting a CDRW in the recorder. The recorder will ask you

to confirm unfinalizing first. Confirm by pressing the EASY

JOG/ENTER key or ENTER on the remote control.

OPEN / CLOSE

REC

PLAY

AUSE

STOP

RECORD

EXT

SOURCE

TYPE

FINALIZE

ERASE

CDR

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

For unfinalized CDRW discs only.

You can erase:

- Tracks can only be erased from the end.

9 10 11

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

- With the EASY JOG you can erase more tracks.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

9 10 11

SYNC MANUAL

RECORD

PROG

Note: It is not possible to erase tracks within the

sequence.

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

- It is also possible to erase the entire disc at once.

2 Press RECORD.

➜ The display will show the total countdown time and

To erase one or more tracks from the end:

1 Press ERASE once.

ERASE. The entire disc will be erased.

➜ The display will show the number of tracks and their

total playing time. ERASE TRACKand PRESS

RECORDwill light up.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

•If the disc is finalized, CD will appear on the display after

inserting a CDRW in the recorder. The recorder will ask you

to confirm unfinalizing first. Confirm by pressing the EASY

JOG/ENTER key or ENTER on the remote control.

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

Erasure of a complete disc may take up to 15 seconds.

2 Select the track(s) you wish to erase by turning the EASY

JOG/ENTER key to the left.

➜ The selected track numbers will start blinking on the

track bar.

➜ The display will show the remaining time after erasing

the selected track(s). The track shown will also be

included in the erasure of tracks.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

9 10

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

9 10

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

3 Press RECORD.

➜ The display will show the total countdown time and

ERASE.

➜ After the selected track(s) has/have been erased, the

display will show the number of remaining tracks and

their total playing time.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING

Play a 2-disc changer (Changer mode)

Playing CDs on Deck 1 and/or Deck 2

(DJ mode)

Your CD recorder is able to play the two decks sequentially

(CHANGER mode). This is the default setting.

With this double deck it is possible to play the CD recorder

deck and/or the CD player deck individually (at the same

time). In this case the extra CD output must also be connected

to an amplifier.

1 Select Changer mode using the DJ MODE key.

➜ CHANGERappears on the display and iCHANGERh

lights up.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

1 Select DJ mode using the DJ MODE key.

➜ DJ MODEappears on the display and j klights up.

10 11 12

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

10 11

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

2 On the deck you want to play, press PLAY/PAUSE 2;to

start CD play.

➜ 2lights up, the track number and track time of the track

being played will appear on the display.

➜ After playing the first disc, the second disc will be

played automatically.

2 On the deck you want to play, press PLAY/PAUSE 2;to

start CD play.

➜ 2lights up and the track number and track time of the

track in play appear on the display.

•Press DISPLAY once, twice or three times to see:

➜ remaining track time, total remaining time, permanent

text information (see Menu mode)

•You can also play the two decks at the same time. By

pressing the CDR key or the CD key you can choose the

deck you want to listen to.

•To interrupt play temporarily, press PLAY/PAUSE 2;again.

➜ ;lights on the display.

•Press DISPLAY once, twice or three times to see:

➜ remaining track time, total remaining time, permanent

text information (see Menu mode)

•To continue play, press PLAY/PAUSE 2;again.

•To interrupt play temporarily, press PLAY/PAUSE 2;again.

➜ ;lights on the display.

3 To stop play, press STOP 9.

➜ The number of tracks and the total playing time appear

on the display.

•To continue play, press PLAY/PAUSE 2;again.

• If you want to see the information for the other deck, press

the CDR key or the CD key in the display frame.

3 To stop play, press STOP 9.

➜ The number of tracks and the total playing time appear

on the display. If you want to see this information about

the other deck, press CDR or CD.

RCE

CDR

RECORD

ANALOG

CDR 77X

AUDIO CD RECORDER

PROG

SHUFFLE

PHONES

DISPLA

DJ MODE

SCROLL

REPEA

PEED

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING

Selecting a track

EASY JOG

STORE/

CANCEL/

DELETE

EASY JOG

STORE/

CANCEL/

DELETE

ENTER

OPEN / CLOSE

REC

PLAY

AUSE

STOP

RECORD

EXT

SOURCE

TYPE

FINALIZE

ERASE

CDR

1 Hold down 5or 6 (in play mode).

➜ The player first searches backwards or forwards at 10

times normal speed with sound at low volume, then

goes to 50 times normal speed with sound muted.

Selecting a track during play

2 Release the button at the desired passage.

➜ Play will start at the desired passage.

1 Turn the EASY JOG/ENTER key until the required track

number appears on the display.

➜ Play will skip to the beginning of the selected track.

Note: During Shuffle, Repeat Track or Programmed play,

search is restricted to within the track being played at

the time.

Select CDR or CD on the remote control and key in the

required track number using the numerical keys on the

remote control. For 2-digit track numbers, press the keys in

rapid succession. For tracks on the other disc, first press CD

or CDR as applicable.

➜ Play skips to the beginning of the selected track.

Press ¡or ™on the remote control one or more times.

➜ Play skips to the beginning of the present, previous or

subsequent tracks, including tracks on the disc in the

other deck. (changer mode only).

Selecting a track when CD play is stopped

1 Turn the EASY JOG/ENTER key until the required track

number appears on the display.

2 Press EASY JOG/ENTER or ENTER on the remote control to

confirm or press PLAY/PAUSE 2;to start playing.

1 Select CDR or CD on the remote control and key in the

required track number using the numerical keys. For 2-digit

track numbers, press the keys in rapid succession. Play

starts.

1 Briefly press ¡or ™ one or more times.

2 Start playback by pressing PLAY/PAUSE 2;, EASY

JOG/ENTER or ENTER on the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

PLAYING

Shuffle (random order) play

Repeat CD, track or program

Only in Changer mode.

1 Press REPEAT one or more times during CD play.

➜ When REPEAT TRACK lights up, the current track will play

repeatedly. When REPEAT ALL lights up, the entire disc or

program plays repeatedly.

1 Select Changer mode, if necessary, using the DJ MODE key.

2 Press SHUFFLE before or during CD play to start shuffle

play.

REM

REC

TRACK TIME

STEP

TIME TRACK

TOTAL REM

➜ The tracks on the CD (or program if set) will play in

10 11

random order.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

3 Press SHUFFLE again to disable the Shuffle mode.

➜ CD recorder will go to Stop mode.

Note: Shuffle is also cleared when you open the disc tray.

2 To return to normal play, press REPEAT one or more times

until:

➜ The REPEAT text disappears from the display.

Note:

- You can use shuffle in combination with REPEAT ALL or

programmed play of the 2-disc changer.

- REPEAT is also cleared when you open the disc tray.

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING

Programming for recording

Remarks about programming

1 Press REC TYPE to select the required recording mode (see

‘Recording’).

•You can program up to 99 tracks to play in any desired

sequence.

2 Compile your program as described in “programming for

playback”. (steps 3 to 5).

•Tracks can be programmed more than once, but each time

counts as a track (STEP).

•A program for playback can be made from both the disc in

the recorder deck and the disc in the player deck. A program

for recording can only be made from the disc in the player

deck.

•Only tracks from the disc in the CD player can be stored.

3 Press RECORD to start recording.

Note:

Programming for playback

- To review the program, press PROG(ram), followed by 5or

6with the CD recorder in Stop mode.

- To add more tracks to the program, repeat steps 1 to 7.

- If you try to store more than 99 tracks, PROG FULLwill

appear on the display.

1 Select Changer mode or DJ mode using the DJ MODE key.

➜ CHANGERor DJ MODEappears on the display.

2 Press CDR or CD to select the required deck.

➜ Selected key lights up.

3 Press PROG(ram) to enter Program mode.

➜ PROG flashes and PROGRAMfollowed by track

information appears on the display.

Clearing a program

1 Press STOP 9if necessary to stop programmed play.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

2 Press STOP 9again to clear the program.

10 11

➜ PROG will disappear from the display.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

•The program is also cleared when you open the disc tray.

Erasing a track from a program

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

1 In Stop mode press PROG(ram) to enter Program mode.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

2 Use 5or 6to select the track that has to be deleted.

➜ The track number and program step will be shown on

the display.

4 Select the required track numbers by turning the EASY

JOG/ENTER key left or right and store by pressing ENTER.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

3 Press CANCEL/DELETE to erase the track from the program.

➜ The remaining program steps and the remaining playing

time on the program will be displayed.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

4 Repeat steps 2 and 3 for all tracks to be erased.

or:

5 Press STOP 9or PROG(ram) to end erasing.

➜ PROG will light up continuously.

Key in a track number with the number keys on the remote

control and press ENTER to confirm. For 2-digit numbers,

press the keys in rapid succession.

➜ The track will be stored in the program.

➜ The track number, total program time and the number of

programmed tracks (STEP) are displayed.

5 Repeat step 4 for all tracks to be programmed.

6 Press STOP or PROG(ram) to end programming.

➜ PROG lights continuously.

7 Press PLAY/PAUSE 2; to start programmed play.

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU MODE

Remarks about Menu mode

General operation of Menu

•In Menu mode you will have access to a number of features

which are not available via the regular keys (on the deck’s

front and the remote control).

Menu active in Recording or Stop mode.

1 When using the remote control, select CDR first.

2 Press STORE/MENU on the deck or the remote control to

enter Menu mode.

➜ TEXT EDITwill appear on the display.

•The TEXT submenus (A-B) allow you to give names to discs

and tracks. The disc and track names will be displayed

during playback.

3 Rotate EASY JOG/ENTER to select the required submenus.

4 Press EASY JOG/ENTER to confirm selections.

•In the RECORDING submenus (D-E) you can set Auto Track

and Balance.

5 Rotate EASY JOG/ENTER to select options in the submenus.

6 Press EASY JOG/ENTER to confirm selections.

•All settings (except Balance) made in Menu mode will be

stored in the deck’s memory and can be called up and

changed at any time.

7 Press STORE/MENU to store settings and return to the

submenu.

8 Press STOP 9to store settings and exit Menu mode.

Note: Text can only be edited for unfinalized discs. (Finalized

CDRW discs must be unfinalized first.)

EASY JOG

STORE/

CANCEL/

DELETE

MAIN MENU

LEVEL 1

LEVEL 2

ENTER

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

ALBUM ARTIST

ALBUM TITLE

ARTIST TR 1

TITLE TR 1

ARTIST TR N

TITLE TR N

10 11 12 13 14 15 16 17

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

CDR

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17

SYNC MANUAL

RECORD

PROG

;

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

MENU/

STORE

PROG.

ENTER CANCEL

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17

ALL TEXT

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

ALBUM ARTIST

ALBUM TITLE

ARTIST TR 1

TITLE TR 1

ARTIST TR N

TITLE TR N

10 11 12 13 14 15 16 17

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17

"TITLE CD 1"

"TITLE CD 2"

"TITLE CD 3"

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

"TITLE CD n"

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

OFF

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11 12 13 14 15 16 17

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

SCAN TRACK

L 100 R 100

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU MODE/CD TEXT

A. Text input/text edit

B. Erasing text/text erase

ALL TEXT

TEXT EDIT

TEXT ERASE

ALBUM ARTIST

ALBUM TITLE

ARTIST TR N

TITLE TR N

NO TEXT

ALBUM TITLE

ARTIST TR N

TITLE TR N

CD Text can be added to a recording or changed.This can be

done in Stop mode or during recording.

1 Press STORE/MENU.

➜ TEXT EDITwill appears on the display.

Text will be stored in the recorder memory and can be edited

until the CDR is finalized. Text on a (unfinalized) CDRW can be

edited at any time.

2 Rotate the EASY JOG/ENTER key to select the TEXT ERASE

submenu.

➜ TEXT ERASEwill appear on the display.

1 Press STORE/MENU.

➜ TEXT EDITwill appear on the display.

3 Press EASY JOG/ENTER to confirm.

➜ If text is available, ALL TEXTwill appear on the

display. (When there is no text available, the message

NO TEXTwill appear on the display.)

2 Press EASY JOG/ENTER to confirm.

➜ ALBUM ARTISTwill appear on the display.

4 Rotate EASY JOG/ENTER to select the required option in

the submenu: ALL TEXT, ALBUM ARTIST, ALBUM

TITLE, ARTIST TR 1, TITLE TR 1, etc.

3 Rotate EASY JOG/ENTER to select the required option in

the submenu: ALBUM ARTIST, ALBUM TITLE,

ARTIST TR 1, TITLE TR 1, etc.

5 Press EASY JOG/ENTER to confirm.

➜ The display will ask you to reconfirm your selection.

ERASE OKwill appear on the display.

4 Press EASY JOG/ENTER to confirm.

➜ The first character space appears on the display.

5 Select the characters by rotating the EASY JOG/ENTER key

or by pressing the corresponding numeric/alphabet key on

the remote control.

6 Press EASY JOG/ENTER to reconfirm.

➜ UPDATEwill appear on the display.

7 Press STORE/MENU to return to the submenu or STOP 9to

exit.

6 Press EASY JOG/ENTER to store each character and move

to the next cursor position.

•With the 5and 6keys you can move to a required cursor

position.

•With the CANCEL key you can delete a character.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

7 Press STORE/MENU to store a name you have entered and

return to the submenu, press 3 to resume or STOP 9to exit.

Note:

- A maximum of 60 characters can be stored per item.

- By pressing the EASY JOG/ENTER key or ENTER on the

remote control without selecting a character first, you can

insert a space between characters.

- When an artist’s name has been stored for a certain track,

the name will automatically be copied for the next track.

The name can be confirmed by pressing STORE/MENU or a

new name can be entered as described above.

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU MODE/CD TEXT

Note:

C. Reviewing CD Text in memory/memory view

- If there are no discs in the memory, the message MEMORY

EMPTYwill appear on the display.

MEMORY VIEW

CD 1

- When the text memory of your CD recorder is full, the

message MEMORY FULLwill appear, followed by

FINALIZE CD. If you want to add a CD to the list of

discs for which text is stored, you will have to erase a disc

from this list or finalize another disc for which text is stored.

- MEMORY FULL/FINALIZE CDmay also appear when

unfinalizing a CDRW disc for which text was stored (see

‘Unfinalizing CDRW discs’). The same action(s) should be

taken in order to obtain memory space.

CD 2

CD N

CD Text is stored in the recorder’s memory. When a CDR(W) is

finalized, the CD Text will be written on the disc and removed

from the recorder’s memory. With the MEMORY VIEW

function you can view/delete the CD Text in the recorder’s

memory for each unfinalized disc. The amount of memory

used is displayed each time the tray opens with an

unfinalized CDR(W) inserted (e.g. MEMORY 9%).

1 Press STORE/MENU.

➜ TEXT EDITwill appear on the display.

2 Rotate the EASY JOG/ENTER key to select the MEMORY

VIEW submenu.

➜ MEMORY VIEWwill appear on the display.

3 Press EASY JOG/ENTER to confirm.

➜ The first album title in the recorder memory will appear

on the display.

4 Select the album title you wish to erase by rotating the

EASY JOG/ENTER key.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

5 Press EASY JOG/ENTER to confirm.

➜ ERASE MEMORYwill appear on the display.

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

10 11

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

6 Press the EASY JOG/ENTER key to confirm the erasure of

the text for that particular disc.

➜ UPDATEwill appear on the display.

7 Press STORE/MENU to return to the submenu or STOP 9to

exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

MENU MODE/RECORDING SETTINGS

D. Auto track increment/auto track

E. Balance (only active in Record/Standby mode)

AUTO TRACK

SET BALANCE

L 100 R 100

OFF

1 Press STORE/MENU.

➜ TEXT EDITwill appear on the display.

1 Press STORE/MENU.

➜ TEXT EDITwill appear on the display.

2 Rotate the EASY JOG/ENTER key to select the AUTO TRACK

submenu.

➜ AUTO TRACKwill appear on the display.

2 Rotate the EASY JOG/ENTER key to select the SET

BALANCE submenu.

➜ SETBALANCEwill appear on the display.

3 Press EASY JOG/ENTER to confirm.

➜ ONwill appear on the display.

3 Press EASY JOG/ENTER to confirm.

➜

FE and L 100 R 100will appear on the

display.

4 Turn the EASY JOG/ENTER key to select Auto track ONor

REM

REC

TRACK TIME

STEP

TIME TRACK

TOTAL REM

OFF.

SYNC MANUAL

RECORD

PROG

•When ONis selected, track numbers will be automatically

incremented during recording.

SHUFFLE ALL

REPEAT

SCAN TRACK

CHANGER

DIGITAL

OPTICAL

ANALOG

•When OFFis selected, you can number the recorded tracks

yourself.

4 Adjust recording balance by turning the EASY JOG/ENTER

key

REM

REC TIME TRACK

TOTAL REM TRACK TIME

STEP

EASY JOG

STORE/

•Turn to the left: the figure on the left (

) counts down, that

10 11

on the right counts up.

SYNC MANUAL

RECORD

PROG

SHUFFLE ALL

REPEAT

CHANGER

DIGITAL

OPTICAL

ANALOG

ENTER

SCAN TRACK

•Turn to the right: the figure on the right (

) counts down,

that on the left counts up.

5 Press EASY JOG/ENTER to confirm.

➜ AUTO TRACKwill appear on the display.

5 Press EASY JOG/ENTER to confirm.

6 Press STORE/MENU to store settings and return to the

6 Press STORE/MENU to store settings.

submenu or STOP 9to exit.

Note: The balance setting will not be stored permanently.

Download from Www.Somanuals.com. All Manuals Search And Download.

FIXING PROBLEMS

Will not record

• clean the disc

TROUBLESHOOTING

• make sure that the CDR(W) is an unfinalized

disc

• make sure that the disc is recordable and

replace if necessary

• the disc is not an AUDIO disc (WRONG

DISC)

• wrong input source chosen. Input label

flashing (CHECK INPUT)

If your CD recorder is defective, it is wise to check this list

first. You may have forgotten a simple step.

Warning!

Under no circumstances should you attempt to repair

the CD recorder yourself because this will invalidate

the guarantee.

• text memory full (MEMORY FULL/

FINALIZE CD). When a CDRW has to be

unfinalized for recording. Erase text for other

disc(s) or finalize other disc(s) to obtain

memory space

• total remaining time is not sufficient; try

programming tracks (see programming)

SYMPTOM • possible solution:

No power • ensure that the ON/OFF button is on (red LED

on): the CD Recorder is in Standby mode,

press any key to activate it

• make sure that the power cable is plugged in

correctly

• switch the recorder OFF and then

immediately back ON

Recording is distorted

• make sure the recording level is correct

Auto track does not work

20 second pause between recordings

• check that auto track on is selected in the

• check if there are 2.7 seconds of silence

between the tracks (analog recording only)

• check if the source is a consumer source with

digital output according to the IEC audio

standard

• see Autostart recording from external CD

player (CD-SYNC)

Player does not react

• switch the ON/OFF button on the front of the

player off and back on

• source is DVD player (no track information)

DISC RECOVERon display

• a power failure has occurred during

recording; the CD recorder is attempting to

repair the disc

• if DISC ERRORthen appears on the

display, the disc cannot be recorded further,

and cannot be finalized. But it can still be

played on the CD recorder or another CD

recorder

No sound • check the audio connections

• if using an amplifier, try using a different

source

Amplifier sound is distorted

• make sure that the CD recorder analog output

is not connected to the amplifier Phono input

• on a CDRW disc, the track being recorded is

lost, but further recording and finalization can

still be done

Play will not start

• make sure that the label of the CD is facing

• clean the disc

• make sure that the disc is not defective by

trying another disc

Remote control does not work

• point the remote control directly at the CD

recorder

• check the batteries and replace if necessary

• select the right source first

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTES

Download from Www.Somanuals.com. All Manuals Search And Download.

The products and services described herein are not necessarily available in all contries.

The specifications and design of this product are subject of change without notice.

Printed in Hungary.

All trademarks acknowledged.

http://www.philips.com

3104 125 2292.2

Download from Www.Somanuals.com. All Manuals Search And Download.

Philips Coffeemaker HD7825 User Manual
Philips Flat Panel Television 15PF9945 37 User Manual
Philips Freezer 37 42PF9731D 10 User Manual
Philips MP3 Player 7FF1MS User Manual
Philips Network Card Network Adaper User Manual
Polk Audio Speaker System RM101 User Manual
Porter Cable Pressure Washer D22885 011 0 User Manual
Praktica Digital Camera D00390 User Manual
Prince Castle Griddle 120 1 User Manual
Pro Ject Turntable Pro Ject RPM 13 Genie User Manual