Return your Warranty Registration card today to
ensure you receive all the benefits you’re entitled to.
AZ 1110 - Family CD Radio Cassette Recorder
POWER SUPPLY
CASSETTE RECORDER
• Once your Philips Magnavox purchase
is registered, you’re eligible to receive all
the privileges of owning a Philips
Magnavox product.
• So complete and return theWarranty
Registration Card enclosed with your
purchase at once.And take advantage
of these important benefits.
BATTERIES (see 1)
AC POWER
CASSETTE PLAYBACK
RECORDING FROM THE RADIO
Whenever convenient, use the power supply if you
want to conserve battery life. Make sure you remove
the power plug from the set and wall outlet before
inserting batteries.
1. Set the source selector to TAPE.
2. Press STOP•OPEN 9 / to open the cassette
holder.
1. Set the source selector to RADIO.
2. Tune to the desired radio station using the TUNING
knob.
3. Press STOP•OPEN 9 / to open the cassette
holder.
1. Check if the power voltage as shown on the type
plate (on the bottom of the set) corresponds to
your local power voltage. If it does not, consult
your dealer or service organisation.
2. If your set is equipped with a voltage selector,
adjust it so that it matches with the local power
voltage
3. Connect the power cord to the AC MAINS outlet
and the wall outlet.
– The set is now ready to use.
4. To switch off the AC power supply completely, pull
the power plug out of the wall outlet.
– Disconnect the power cord when you change
over to battery supply, or to protect the set
during heavy thunderstorms.
3. Insert a recorded cassette.
AZ 1110 Family CD Radio Cassette Recorder
4. Press PLAY 1 and playback will start.
5. Adjust the sound using the VOLUME, and DBB
controls.
6. For brief interruptions, press PAUSE ;. Press
PAUSE ; again to resume playback.
7. By pressing 5 or 6, fast winding of the tape is
possible in both directions.
8. To stop playback, press STOP•OPEN 9 /.
– The keys are automatically released at the end
of the tape.
9. Set the source selector to TAPE/POWER OFF
position (with the cassette keys released) to
switch off the set.
Batteries (optional)
4. Insert a blank cassette.
1. Open the battery compartment and insert as
shown six batteries, type R20, or D-cells.
2. Replace the compartment door, making sure the
batteries are firmly and correctly in place.
3. Remove the batteries if exhausted or if they will
not be used again for a long period.
5. Press RECORD 0 to start recording.
6. For brief interruptions, press PAUSE ;. To resume
recording, press PAUSE ; again.
7. To stop, press STOP•OPEN 9 /.
Warranty
Owner
Model
Verification
Confirmation Registration
Registering your product
within 10 days confirms
your right to maximum
protection under the
terms and conditions of
your Philips Magnavox
warranty.
Your completed Warranty Returning your Warranty
Registration Card serves
as verification of
Registration Card right
away guarantees you’ll
CD SYNCHRO START RECORDING
OO
WW
EE
RR
OO
NN
ownership in the event of receive all the information
•C
•C
A
AD
DIO
IO
D
D
1. Set the source selector to CD.
•R
•R
APE
PE
•T
•TA
P
– The incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst.
Therefore:
– Do not mix battery types, e.g. alkaline with zinc
carbonate.
– When inserting new batteries, replace all
batteries at the same time.
– Remove the batteries if the set is not be used
for a long time.
PO
OW
WER
ER
O
F
FF
F
DB
A
product theft or loss.
and special offers which
you qualify for as the
owner of your model.
B
D
Y
N
M
IC
B
O
O
S
T
2. Insert a CD and if desired, program track numbers.
3. Press STOP•OPEN 9 / to open the cassette
holder.
O
OPPEN
E
N
F
FMM
-
-
-
-
M
M
W
W
MW
M
W
4. Insert a blank cassette.
P
PAU
US
E
E
Environmental information
S
STO
T
OP
5. Press RECORD 0 to start recording.
– Playing of the CD program starts automatically
from the beginning of the program. It is not
necessary to start the CD player separately.
6. For brief interruptions, press PAUSE ;. To resume
recording, press PAUSE ; again.
•
O
PE
P
EN
N
S
SEA
R
RC
CH
H
CASSETTE RECORDING (see 6 / 7 )
PLA
PLA
Y
Y
R
RECO
All redundant packaging material has been
omitted. We have done our utmost to make
the packaging easily separable into three
mono materials: cardboard (box),
expandable polystyrene (buffer) and
polyethylene (bags, protective foam sheet).
ORD
D
PL
AY
•P
AUS
E
General information on cassette recording
– Recording is permissible insofar as copyright or
other rights of third parties are not infringed.
– This deck is not suited for recording on CHROME
(IEC II) or METAL (IEC IV) type cassettes. For
recording you should use NORMAL type cassettes
(IEC I) on which the tabs have not been broken.
– The recording level is set automatically. Altering
the VOLUME control or, DBB switch will not affect
the recording in progress.
S
H
U
FF
LE
Know these
ST
S
TO
P
P
S
E
S
AR
ARC
CH
H
For Customer Use
safety
CAUTION
symbols
Enter below the Serial No. which is
located on the rear of the cabinet. Retain
this information for future reference.
M
MO
OD
DE
E
Note: The battery supply is switched off when the
set is connected to the AC power supply.
7. To stop recording press STOP•OPEN 9 /.
To select and record a particular passage
within a track
Your set consists of materials which
can be recycled if dissassembled by a
specialized company. Please observe
the local regulations regarding the
disposal of packaging materials,
Model No. _______________________
Serial No. ________________________
RISK OF ELECTRIC SHOCK
DO NOT OPEN
1. Press SEARCH ∞ or § to select a passage.
2. Put the CD player in PAUSE ; position at the
selected passage.
– Recording will start from this exact point when
you press RECORD 0.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
– No recording will take place during the first 7
seconds, when the leader tape passes the recorder
heads.
exhausted batteries and old equipment.
– To prevent the accidental erasure of a recording,
keep the cassette side to be safeguarded in front
of you and break out the left tab. Recording on this
side is no longer possible.
This “bolt of lightning”
indicates uninsulated material
twithin your unit may cause an
electrical shock. For the safety of
everyone in your household, please do
not remove product covering.
WARNING: TO PREVENT
FIRE OR SHOCK HAZARD, DO
NOT EXPOSE THIS EQUIPMENT TO
RAIN OR MOISTURE.
Both the model and production numbers can be found
on the bottom of the set.
Owner’s Manual
Mode d’emploi
Instructivo de manejo
CAUTION: To prevent electric
shock, match wide blade of plug to
wide slot, and fully insert.
The “exclamation point” calls
attention to features for which
syou should read the enclosed
literature closely to prevent operating
and maintenance problems.
PHILIPS CONSUMER ELECTRONICS COMPANY
A Division of Philips Electronics North America Corporation
Knoxville, Tennessee 37914-1810, U.S.A.
MAC5097
Printed in Hong Kong
TCtext/CvB/747
SAFETY
OPERATION/RADIO
CD PLAYER
MAINTENANCE
1
2
3
6 x D-cells - R14
FM
AM
GENERAL OPERATION
CD DISPLAY INDICATION (see 4)
RECORDER MAINTENANCE (see 0)
WARNING
PRECAUTIONS & GENERAL MAINTENANCE
(see 8 / 9)
çCanada
1. To switch on the set, use the source selector
2. Adjust the sound using the VOLUME control and
DBB switch.
3. To switch off the set, set the source selector to
TAPE/OFF position, with the cassette keys
released.
– Total track number: in stop position.
– Current track number: during CD play.
– Current track number flashes: in PAUSE mode.
– SHUFFLE/REPEAT mode: the respective mode is
activated.
– PROGRAM: program function is active, P also
appears briefly when you store a track.
– No: error in CD operation or with the CD, or no
disc (see Troubleshooting).
To ensure a good recording and playback quality,
clean the indicated parts A,Band Cafter every 50
hours of operation or, on average, once a month. Use
a cotton bud slightly moistened with alcohol or a
special head cleaning fluid.
• Press PLAY 1 and clean the rubber pressure
roller C.
• Then press PAUSE ; and clean the capstan Band
the heads A.
To reduce the risk of fire or
electric shock, do not expose this
appliance to rain or moisture.
#
%
$
This digital apparatus does not exceed the
Class B limits for radio noise emissions
from digital apparatus as set out in the Ra-
dio Interference Regulations of the Cana-
dian Department of Communications.
PW
ER
O
N
ER
ON
– Place the set on a hard, flat surface so that it does
not tilt.
CD
•D
•
T
IO
•A
POW
E
A
E
I
O
O
FF
PO
WER
DB
DYNA
MIC
BOST
OFF
B
DB
B
NAMIC
OS
DY
T
OPE
N
FM
O
PEN
-
FM
AM
-
-
AM
-
AM
AM
P
AU
U
S
S
E
P
PA
AUS
S
E
E
S
STO
P
O
P
•
O
P
S
ST
TO
O
P
P
P
E
N
•
PE
OPE
N
S
EA
R
A
CH
RC
S
SE
EAR
H
R
C
CH
H
P
PLA
L Y
A
Y
P
PLA
L Y
A
Y
R
RE
EC
CO
OR
R
D
R
RE
EC
C
PLA
O
OR
RD
D
Y•PAUSE
P
LA
Y
•PAU
SE
SHU
FFLE
S
HUF
FLE
STO
P
ST
OP
SEA
RCH
SEA
RCH
– Do not expose the set, CDs, batteries or cassettes
to humidity, rain, sand, direct sunlight or other
places where high temperatures can occur, such as
in the vicinity of heating apparatus or in motor
cars parked in the sun.
– Do not cover the set. The amplifier produces heat
which must dissipate freely, so make sure that
there is sufficient ventilation around the set.
A minimum gap of 15 cm is necessary.
– The mechanical parts of the CD player and the
cassette deck contain self-lubricating bearings and
must not be oiled or lubricated.
– A chamois leather slightly moistened with water is
sufficient for cleaning the housing. Do not use
cleaning agents containing alcohol, spirits,
ammonia or abrasives as these may harm the
housing.
MOD
E
MO
DE
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazard-
ous radiation exposure.
RADIO (see 2 / 3)
5
4
1. Set the source selector to RADIO.
2. Adjust the sound using the VOLUME control and
the DBB switch.
3. Select the wave band using the FM-AM band
selector.
4. Tune to a radio station using the TUNING knob.
– For FM, pull out the telescopic antenna. To
improve FM-reception, incline and turn the
antenna. Reduce its length if the FM-signal is
too strong (very close to a transmitter).
– For AM, the set is provided with a built-in
antenna, so the telescopic antenna is not
needed. Direct the antenna by turning the
whole set.
REPEAT
ALL
x 4
– F: Program memory full, when you try to store
more then 20 tracks
• After cleaning, press STOP•OPEN 9 /.
Cleaning of the heads Acan also be done by playing
a cleaning cassette through once.
x 3
REPEAT
ALL
SHUFFLE
REPEAT
The set complies with the FCC-Rules, Part 15
and with 21 CFR 1040.10
x 2
PLAYING A CD
SHUFFLE
REPEAT
ALL
1. Set the source selector to CD.
2. To open the CD compartment, press OPEN on the
the CD door.
3. Insert the audio CD, printed side facing up.
4. To close the CD compartment, push the door down.
– The CD player scans the contents of the CD and
the total number of tracks is displayed
5. Press PLAY•PAUSE 2; to start playback.
6. Adjust the sound using the VOLUME control and
the DBB switch.
PROGRAM
SHUFFLE
SAFETY INSTRUCTIONS – Read before operating equipment
x 1
This product was designed and manufactured to meet
strict quality and safety standards.There are, however, some
installation and operation precautions which you should be
particularly aware of.
11. Grounding or
Polarization - Precautions
that should be taken so that
the grounding or
6
7
8
AC
Polarized
Plug
polarization means of an
appliance is not defeated.
1. Read Instructions - All the safety and operating
instructions should be read before the appliance is
operated.
2. Retain Instructions - The safety and operating
instructions should be retained for future reference.
3. Heed Warnings - All warnings on the appliance
and in the operating instructions should be adhered
to.
CAUTION:
To prevent electric shock,
CD MAINTENANCE
match the wide blade of this plug to the wide slot,
thenfully insert. Do not use this (polarized) plug
with an extension cord, receptacle or other outlet
unless the blades can be fully inserted to prevent
blade exposure.
1
PWE
R
ON
•CD
ADIO
T
E
PR
F
DB
DYNAM
IC
BOOS
B
5. To switch off the set, set the source selector to
TAPE/ POWER OFF position, with the cassette keys 7. To interrupt playback, press PLAY•PAUSE 2;.
released.
T
OPEN
FM
AM
-
-
– The lens of the CD player should never be touched.
– The lens may cloud over if the CD player is moved
from cold to warm surroundings. The CD player
will not start. Give the player some time to
acclimatise.
– To take a CD out of its box, press the center
spindle while lifting the CD. Always pick up the CD
by the edge and replace the CD back in its box
after use to avoid scratching and dust.
– To clean the CD, wipe in a straight line from the
center towards the edge using a soft, lint-free
cloth. Do not use cleaning agents as they may
damage the disc.
AM
P
AU
SE
U
S
STO
OP
P
•
O
OP
P
E
EN
N
S
E
SEA
AR
RCH
H
P
PLA
L Y
A
Y
R
C
RECO
ORD
R
D
PLA
Y
•PAU
SE
!
@
SHUF
FLE
STOP
SEAR
CH
MOD
E
Press PLAY•PAUSE 2; again to continue
playback.
8. Press STOP 9 to stop CD playback.
9. Set the source selector to TAPE/OFF position to
switch off the set.
Note: CD playback will also stop when:
– the CD has reached the end;
– the CD door is opened;
12. Power-Cord Protection - Power supply cords
should be routed so that they are not likely to be
walked on or pinched by items placed upon or
against them, paying particular attention to cords
and plugs, convenience receptacles, and the point
where they exit from the appliance.
4. Follow Instructions - All operating and use
instructions should be followed.
O
W
9
E
R
O
N
5. Water and Moisture - The appliance should not
be used near water - for example, near a bathtub,
washbowl, kitchen sink, laundry tub, in a wet
basement or near a swimming pool, etc.
6. Carts and Stands - The appliance should be
used only with a cart or stand that is recommended
by the manufacturer.
•C
•R
A
PE
D
0
9
D
IO
•T
A
P
O
W
E
R
O
F
F
DB
B
D
Y
N
A
M
IC
O
O
S
T
1
2
13. Cleaning - The appliance should be cleaned only
O
P
E
N
F
M
-
A
M
-
as recommended by the manufacturer.
14. Power Lines - An outdoor antenna should be
located away from power lines.
15. Nonuse Periods - The power cord of the appli-
ance should be unplugged from the outlet when left
unused for a long period of time.
16. Object and Liquid Entry - Care should be taken
so that objects do not fall and liquids are not spilled
into the enclosure through openings.
17. Damage Requiring Service - The appliance
should be serviced by qualified service personnel
when:
A.The power-supply cord or the plug has been
damaged; or
B. Objects have fallen, or liquid has spilled into the
appliance; or
C.The appliance has been exposed to rain; or
D. The appliance does not appear to operate
normally or exhibits a marked change in
performance; or
E. The appliance has been dropped, or the enclosure
damaged.
18. Servicing - The user should not attempt to service
the appliance beyond that described in the operating
instructions. All other servicing should be referred to
qualified service personnel.
A
M
– the source selector is in the RADIO or
TAPE/OFF position.
6A.
An appliance and cart combination
should be moved with care. Quick stops,
excessive force, and uneven surfaces may
cause the appliance and cart combination
to overturn.
CLASS 1
LASER PRODUCT
8
7
3
4
PA
PA
US
U
SE
E
ST
ST
OP
O
P
•
•
O
OPEN
PE
N
SEARCH
SEARCH
PLA
PLA
Y
Y
RECORD
RECORD
PLA
Y
•
P
AUS
E
– Never write on a CD or attach stickers to it.
7. Wall or Ceiling Mounting - The appliance
should be mounted to a wall or ceiling only as
recommended by the manufacturer.
0
S
HUF
FLE
ST
OP
SEARCH
8. Ventilation - The appliance should be situated so
that its location or position does not interfere with
its proper ventilation. For example, the appliance
should not be situated on a bed, sofa, rug, or similar
surface that may block the ventilation openings; or,
placed in a built-in installation, such as a bookcase
or cabinet that may impede the flow of air through
the ventilation openings.
9. Heat - The appliance should be situated away from
heat sources such as radiators, heat registers, stoves,
or other appliances (including amplifiers) that
produce heat.
MODE
A
A B C
5
6
10. Power Sources - The appliance should be
connected to a power supply only of the type
described in the operating instructions or as
marked on the appliance.
91/8
EL 4562-1
LIMITED WARRANTY
English
Français
Español
CD PLAYER
TROUBLESHOOTING
If a fault occurs, first check the points listed below before taking the set for repair.
If you are unable to remedy a problem by following these hints, consult your dealer or service center.
WARNING: Under no circumstances should you try to repair the set yourself, as this would invalidate the
warranty.
1
2
3
DBB (Dynamic Bass Boost) – to increase the bass level
pour amplifier les fréquences basses
pour régler le niveau sonore
Refuerzo dinámico de tonos bajos) – para reforzar los tonos bajos
para ajustar el volumen
PHILIPS MAGNAVOX PORTABLE COMPACT DISC
OneYear Free Exchange
SEARCH ∞ or §
VOLUME
– to adjust the volume level
Selecting a different track during playback
– You can jump to the next track by pressing
SEARCH § once. If you want to skip more than
one track, press SEARCH § more than once until
the display shows the desired track number.
– If you want to repeat the running track from the
beginning, press SEARCH ∞ once. If you want to
repeat one of the previous tracks, press
2. To leave the SHUFFLE/REPEAT modes, press the MODE
button repeatedly until the various SHUFFLE/REPEAT
modes are no longer shown on the display. You can also
press STOP 9 to quit playback.
This product must be carried in for an exchange.
Cassette keys
PAUSE ;
Touches de la platine cassette
pour interrompre la lecture
pour interrompre la lecture et ouvrir le compartiment à cassette
rembobinage rapide de la cassette vers l'avant
rembobinage rapide de la cassette vers l'arrière
pour démarrer la lecture
Teclas del cassette
– to interrupt playback
para interrumpir la reproducción
para parar la reproducción y abrir el compartimiento del cassette
para avance rápido de la cinta
para avance rápido de la cinta
para iniciar la reproducción
WHO IS COVERED?
EXCHANGING A PRODUCT IN U.S.A.,
PUERTO RICO OR U.S.VIRGIN ISLANDS...
Contact your dealer to arrange an exchange. Or, ship
the product, insured and freight prepaid, and with proof
of purchase enclosed, to the address listed below.
Small Product Service Center
You must have proof of purchase to exchange the
product.A sales receipt or other document showing
that you purchased the product is considered proof of
purchase.Attach it to this owner’s manual and keep
both nearby.
STOP•OPEN 9 /
SEARCH 5
SEARCH 6
PLAY 1
– to stop playback and open the cassette compartment
– to fast forward the tape
– to fast rewind the tape
PROBLEM
POSSIBLE CAUSE
REMEDY
PROGRAMMING TRACK NUMBERS
– to start playback
You may store at most 20 tracks in the memory in the
desired sequence.
You may store any track more than once.
Set does not react to operation – Electrostatic discharge.
of any control.
• Switch off the set, disconnect
the power plug and reconnect
after a few seconds.
Philips Service Company
RECORD 0
– to start recording
pour démarrer l'enregistrement
para iniciar la grabación
WHAT IS COVERED?
907 Snapps Ferry Road, Plant 2, Building 6
Greeneville,TN 37743
SEARCH ∞ more than once until the display
shows the desired track number.
Warranty coverage begins the day you buy your
product. For one year thereafter, a defective or
inoperative product will be replaced with a new,
renewed or comparable product at no charge to you.A
replacement product is covered only for the original
warranty period.When the warranty on the original
product expires, the warranty on the replacement
product also expires.
4
CD buttons
PLAY•PAUSE 2;
STOP 9
Touches du lecteur de CD
pour démarrer ou interrompre la lecture du CD
pour interrompre la lecture
pour sauter ou rechercher un passage ou une plage spécifique
pour sélectionner un mode de lecture différent (par ex.: SHUFFLE ou
REPEAT) et pour programmer les numéros de plages
Botones de CD (disco compacto)
para iniciar o interrumpir la reproducción del CD
para parar la reproducción
para buscar o saltar a una parte o una pista particular
para seleccionar un modo de reproducción distinto, por ejemplo,
SHUFFLE (mezcla) o REPEAT (repetir) y programar números de pista
(In U.S.A., Puerto Rico and U.S.Virgin Islands, all implied
warranties, including implied warranties of
merchantability and fitness for a particular purpose, are
limited in duration to the duration of this express
warranty. But, because some states do not allow
limitations on how long an implied warranty may last,
this limitation may not apply to you.)
– to start or interrupt CD playback
– to stop playback
Display does not function
properly.
– Electrostatic discharge.
• Switch off the set, disconnect
the power plug and reconnect
after a few seconds.
Programming track numbers
Starting with a particular track
1. In the stop position select the desired track using
SEARCH ∞ or SEARCH § until the display shows
the desired track number.
2. Store the desired track by pressing MODE 6once.
– The display shows P and PROGAM followed by
your selected track number.
SEARCH ∞ §
MODE
– to skip or search a passage or a track
– to select a different playback mode e.g. to SHUFFLE or
REPEAT and to program track numbers
1. In the STOP position you can select a desired track
using the SEARCH ∞ or § button.
2. Press PLAY•PAUSE 2; to start playback.
No sound.
– VOLUME is not adjusted.
– Headphones are connected.
– Batteries are exhausted.
– Batteries are incorrectly
inserted.
• Adjust the VOLUME.
• Disconnect headphones.
• Insert new batteries.
5
6
7
8
9
0
!
CD display
– to indicate CD functions
indique les fonctions du lecteur de CD
Compartiment à cassette
para indicar las funciones de CD
WHAT IS EXCLUDED?
Your warranty does not cover:
EXCHANGING A PRODUCT IN CANADA...
Please contact Philips at:
• Insert the batteries correctly.
Cassette compartment
TUNING
Compartimiento del cassette
Searching for a passage within a track
• labor charges for installation or setup of the product,
adjustment of customer controls on the product, and
installation or repair of antenna systems outside of
the product.
• product repair and/or part replacement because of
misuse, accident, unauthorized repair or other cause
not within the control of Philips Consumer
Electronics Company.
• reception problems caused by signal conditions or
cable or antenna systems outside the unit.
• a product that requires modification or adaptation to
enable it to operate in any country other than the
country for which it was designed, manufactured,
approved and/or authorized, or repair of products
damaged by these modifications.
• incidental or consequential damages resulting from
the product. (Some states do not allow the exclusion
of incidental or consequential damages, so the above
exclusion may not apply to you.This includes, but is
not limited to, prerecorded material, whether
copyrighted or not copyrighted.)
1-800-661-6162 (French Speaking)
1-800-363-7278 (English Speaking)
– to tune to radio stations
You can search for a passage within a track. The CD
is played at low volume and at high speed, however,
the sound is still recognizable.
1. Keep the SEARCH ∞ or § button pressed during
playback, and release the button as soon as you
recognize the desired passage:
3. Select and store all desired tracks of a CD in this
way.
pour sélectionner les stations radio
Indicateur de syntonisation
para sintonizar emisoras de radio
– Power cord is not securely
connected.
• Connect the power cord
properly.
Tuning dial pointer
Band selector
OPEN
Puntero del dial de sintonización
(In Canada, this warranty is given in lieu of all other
warranties. No other warranties are expressed or
implied, including any implied warranties of
merchantability or fitness for a particular purpose.
Philips is not liable under any circumstances for any
direct, indirect, special, incidental or consequential
damages, howsoever incurred, even if notified of the
possibility of such damages.)
– to select the wave band (FM-AM)
– to open the CD door
pour sélectionner la bande de longueur d'ondes (FM-AM)
pour ouvrir le compartiment du disque
para seleccionar la banda de onda (FM-AM)
para abrir la puerta del CD
Bad sound.
– Batteries are exhausted.
• Replace batteries.
Checking a program
Severe radio hum or noise.
– Set too close to TV, VCR or
computer.
• Increase the distance.
1. To review the set program, in the stop position
press and hold MODE for more than 2 seconds.
– The display will show the track numbers you
have selected in sequence.
2. To start playback of the program,
press PLAY•PAUSE 2;.
– Playback starts with the first track of the
program. After the last track, playback stops
and the display shows the CD’s total number of
tracks.
Source selector
– POWER ON/OFF switch and to select the sound source:
CD - RADIO - TAPE
POWER ON/OFF et pour sélectionner la source sonore : CD-TUNER-
TAPE
interruptor de POWER ON/OFF (apagado/encendido) y selector de la
fuente de sonido: CD - TUNER (sintonización) - TAPE (cinta)
– Normal CD playback will resume from this
point.
Poor radio reception.
– Weak radio signal.
• FM: aim and extend the
telescopic antenna for best
reception; (see 2)
@ p
– 3.5 mm headphone socket
prise casque 3,5 mm
zócalo de auricular de 3,5 mm
TO GET OUT-OF-WARRANTY EXCHANGE...
In U.S.A., Puerto Rico or U.S.Virgin Islands, contact
Philips Service Company at (800) 851-8885 to obtain
the cost of out-of-warranty exchange.Then carefully
pack the product and ship it to the Small Product
Service Center (address listed above). In Canada, call the
phone number listed above under “Exchanging a Product
a Canada” to obtain the cost of out-of-warranty
exchange.
SHUFFLE/REPEAT (see 5)
• AM: rotate the entire set
(see 3).
BACK PANEL
PANNEAU ARRIÈRE
PANEL TRASERO
The MODE button allows you to select four different modes
which can also be combined with PROGRAM. The modes
can be selected or changed during playback and will flash
for 2 seconds before playing your selected mode.
1. During playback only, press MODE until the desired
function appears on the display.
SHUFFLE - Tracks are played in random order.
REPEAT ALL, SHUFFLE - Continuous playback of
tracks in random order.
REPEAT - Continuous playback of the current track.
REPEAT ALL - Repeats the entire CD.
– During playback you can use SEARCH ∞ or
SEARCH § to skip tracks.
#
$
%
Telescopic antenna
– to improve FM reception
– for power cord
pour améliorer la réception en modulation de fréquence
prise pour le branchement sur secteur
compartiment à piles
para mejorar la recepción de FM
enchufe para el cable de la red eléctrica
para abrir el compartimiento de la batería
Poor cassette sound quality.
– Dust and dirt on the heads,
capstan or pressure roller.
• Clean the heads etc., see
Maintenance
AC MAINS
Battery door
– to open the battery compartment
– Use of incompatible cassette
types (METAL or CHROME).
• Only use NORMAL (IEC I) for
recording
• a product that is used for commercial or institutional
purposes.
Erasing a program
REMEMBER...
Recording does not work.
CD playback does not work.
– Cassette tab(s) may be broken
out.
• Apply a piece of adhesive tape
over the missing tab space.
You can erase the contents of the memory by;
– opening the CD door;
– setting the source selector to the TAPE or RADIO
position.
– pressing STOP twice during playback/in the stop
position.
Please record the model and serial numbers found on
the product below.Also, please fill out and mail your
warranty registration card promptly. It will be easier for
us to notify you if necessary.
WHERE IS EXCHANGE AVAILABLE?
You may exchange the product in all countries where
the product is officially distributed by Philips Consumer
Electronics Company. In countries where Philips
Consumer Electronics Company does not distribute the
product, the local Philips service organization will
attempt to provide a replacement product (although
there may be a delay if the appropriate product is not
readily available).
– CD is badly scratched or dirty.
• Replace or clean the CD, see
Maintenance.
– No CD inserted.
• Insert CD.
MODEL # __________________________________
SERIAL # __________________________________
– CD inserted upside down.
• Insert CD with printed side
facing up.
– Laser lens is steamed up.
• Wait until lens has
acclimatized.
BEFORE REQUESTING EXCHANGE...
Please check your owner’s manual before requesting an
exchange.Adjustments of the controls discussed there
may save you a trip.
The CD skips tracks.
– CD is damaged or dirty.
– PROGRAM/SHUFFLE is active.
• Replace or clean the CD.
• Switch off the PROGRAM/-
SHUFFLE function.
This warranty gives you specific legal rights.You may have other rights which vary from state/province to state/province.
Philips Service Company, P.O. Box 555, Jefferson City,Tennessee 37760, (423) 475-8869
EL4967E003 / MAC 4108 / 1-97
Download from Www.Somanuals.com. All Manuals Search And Download.
|