Register your product and get support at
32PFL3605H/12
42PFL3605H/12
47PFL3605H/12
EN
User Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
6 Install channels
Automatically install channels
Manually install channels
Rename channels
26
26
27
28
28
28
Contents
1 Notice
2
4
Rearrange channels
Test digital reception
2 Important
7 Connect devices
Back connector
29
29
31
32
33
34
35
3 YourTV
7
7
7
Side connector
Side controls and indicators
Remote control
Connect a computer
Use a Conditional Access Module
Use Philips EasyLink
Use a Kensington lock
4 Use yourTV
9
9
9
10
10
10
Switch yourTV on / off or to standby
Switch channels
8 Product information
Supported display resolutions
Multimedia
36
36
36
36
36
36
37
37
Watch connected devices
AdjustTV volume
Use teletext
Tuner / Reception /Transmission
Remote control
Power
SupportedTV mounts
Product specification
5 Use more of yourTV
11
11
AccessTV menus
Rename devices from the home menu 11
Remove devices from the home menu 11
Change picture and sound settings
Use the universal access menu
Use advanced teletext features
12
15
15
9 Troubleshooting
GeneralTV issues
TV channel issues
Picture issues
38
38
38
38
39
39
39
39
Create and use list of favourite channels 16
Use the Electronic Programme Guide
Use theTV clock
17
18
19
20
21
Sound issues
HDMI connection issues
Computer connection issues
Contact us
Use timers
UseTV locks
Use subtitles
View photos and play music from a
USB storage device
22
23
24
24
25
25
25
10 Index
40
Listen to digital radio channels
Update theTV software
ChangeTV preferences
Access decoder channel
Start aTV demo
Reset theTV to factory settings
EN
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Pixel characteristics
1 Notice
This LCD product has a high number of
colour pixels.Although it has effective pixels of
99.999% or more, black dots or bright points of
light (red, green or blue) may appear constantly
on the screen.This is a structural property of
the display (within common industry standards)
and is not a malfunction.
2010 © Koninklijke Philips Electronics N.V.All
rights reserved.
Specifications are subject to change without
notice.Trademarks are the property of
Koninklijke Philips Electronics N.V or their
respective owners. Philips reserves the right
to change products at any time without being
obliged to adjust earlier supplies accordingly.
The material in this manual is believed
adequate for the intended use of the system.
If the product, or its individual modules or
procedures, are used for purposes other than
those specified herein, confirmation of their
validity and suitability must be obtained. Philips
warrants that the material itself does not
infringe any United States patents. No further
warranty is expressed or implied.
Compliance with EMF
Koninklijke Philips Electronics N.V. manufactures
and sells many products targeted at consumers
which, like any electronic apparatus, in
general have the ability to emit and receive
electromagnetic signals.
One of Philips’ leading Business Principles is to
take all necessary health and safety measures
for our products, to comply with all applicable
legal requirements and to stay well within
the EMF standards applicable at the time of
producing the products.
Philips is committed to develop, produce and
market products that cause no adverse health
effects. Philips confirms that if its products are
handled properly for their intended use, they
are safe to use according to scientific evidence
available today.
Philips plays an active role in the development
of international EMF and safety standards,
enabling Philips to anticipate further
developments in standardisation for early
integration in its products.
Warranty
•
Risk of injury, damage to TV or void of
warranty! Never attempt to repair the TV
yourself.
•
•
Use the TV and accessories only as
intended by the manufacturer.
The caution sign printed on the back of
the TV indicates risk of electric shock.
Never remove the TV cover. Always
contact Philips Customer Support for
service or repairs.
Mains fuse (UK only)
ThisTV is fitted with an approved moulded
plug. Should it become necessary to replace
the mains fuse, this must be replaced with a
fuse of the same value as indicated on the plug
(example 10A).
1 Remove fuse cover and fuse.
•
Any operation expressly prohibited in
this manual, or any adjustments and
assembly procedures not recommended
or authorised in this manual shall void the
warranty.
2 The replacement fuse must comply with
BS 1362 and have the ASTA approval
mark. If the fuse is lost, contact your
dealer in order to verify the correct type.
3 Refit the fuse cover.
In order to maintain conformity to the EMC
directive, the mains plug on this product must
not be detached from the mains cord cable.
2
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Copyright
®
Kensington and Micro Saver are registered US
trademarks of ACCO World corporation with
issued registrations and pending applications in
other countries throughout the world.
Manufactured under licence from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Note
• Available in selected models only
HDMI, the HDMI logo and High-Definition
Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC.
All other registered and unregistered
trademarks are the property of their respective
owners.
EN
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
When stand mounting the TV, use only
the supplied stand. Secure the stand to
the TV tightly. Place the TV on a flat, level
surface that can support the combined
weight of the TV and the stand.
When wall mounting the TV, use only a
wall mount that can support the weight of
the TV. Secure the wall mount to a wall
that can support the combined weight of
the TV and wall mount. Koninklijke Philips
Electronics N.V. bears no responsibility
for improper wall mounting that result in
accident, injury or damage.
2 Important
Read and understand all instructions before you
use yourTV. If damage is caused by failure to
follow instructions, the warranty does not apply.
Safety
Risk of electric shock or fire!
•
Never expose the TV to rain or water.
Never place liquid containers, such as
vases, near the TV. If liquids are spilt on
or into the TV, disconnect the TV from
the power outlet immediately. Contact
Philips Consumer Care to have the TV
checked before use.
Never place the TV, remote control or
batteries near naked flames or other heat
sources, including direct sunlight.
To prevent the spread of fire, keep
candles or other flames away from the
TV, remote control and batteries at all
times.
Risk of injury to children!
Follow these precautions to prevent the
TV from toppling over and causing injury to
children:
•
Never place the TV on a surface covered
by a cloth or other material that can be
pulled away.
Ensure that no part of the TV hangs over
the edge of the surface.
Never place the TV on tall furniture (such
as a bookcase) without anchoring both
the furniture and TV to the wall or a
suitable support.
Educate children about the dangers of
climbing on furniture to reach the TV.
•
•
•
•
Risk of overheating!
•
Never install the TV in a confined space.
Always leave a space of at least 4 inches
or 10 cm around the TV for ventilation.
Ensure curtains or other objects never
cover the ventilation slots on the TV.
•
•
Never insert objects into the ventilation
slots or other openings on the TV.
When the TV is swivelled ensure that
no strain is exerted on the power cord.
Strain on the power cord can loosen
connections and cause arcing.
Risk of damage to the TV!
•
Before you connect the TV to the power
outlet, ensure that the power voltage
matches the value printed on the back
of the TV. Never connect the TV to the
power outlet if the voltage is different.
Risk of short circuit or fire!
•
Never expose the remote control or
batteries to rain, water or excessive heat.
Avoid force coming onto power plugs.
Loose power plugs can cause arcing or
fire.
Risk of injury, fire or power cord damage!
•
•
Never place the TV or any objects on the
power cord.
To disconnect the TV power cord easily
from the power outlet, ensure that you
have full access to the power cord at all
times.
•
Risk of injury or damage to the TV!
•
Two people are required to lift and carry
a TV that weighs more than 25 kg.
4
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
When you disconnect the power cord,
always pull the plug, never the cable.
Disconnect the TV from the power
outlet and antenna before lightning
storms. During lightning storms, never
touch any part of the TV, power cord or
antenna cable.
Disposal of your old product and
batteries
Your product is designed and manufactured
with high quality materials and components,
which can be recycled and reused.
Risk of hearing damage!
•
Avoid using earphones or headphones at
high volumes or for prolonged periods of
time.
Low temperatures
•
If the TV is transported in temperatures
below 5°C, unpack the TV and wait
until the TV temperature matches room
temperature before connecting the TV to
the power outlet.
When this crossed-out wheeled bin symbol
is attached to a product it means that the
product is covered by the European Directive
2002/96/EC. Please inform yourself about the
local separate collection system for electrical
and electronic products.
Please act according to your local rules and
do not dispose of your old products with your
normal household waste.
Correct disposal of your old product helps to
prevent potential negative consequences for
the environment and human health.
Screen care
•
Avoid stationary images as much as
possible. Stationary images are images
that remain on-screen for extended
periods of time. Examples include:
on-screen menus, black bars and time
displays. If you must use stationary
images, reduce screen contrast and
brightness to avoid screen damage.
Unplug the TV before cleaning.
Your product contains batteries covered by
the European Directive 2006/66/EC, which
cannot be disposed with normal household
waste.
Please inform yourself about the local rules
on separate collection of batteries because
correct disposal helps to prevent negative
consequences for the environmental and
human health.
•
•
Clean the TV and frame with a soft,
damp cloth. Never use substances such as
alcohol, chemicals or household cleaners
on the TV.
•
•
Risk of damage to the TV screen! Never
touch, push, rub or strike the screen with
any object.
To avoid deformations and colour fading,
wipe off water drops as soon as possible.
EN
5
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Low standby power consumption
The class-leading and highly advanced
power circuitry brings down the power
consumption of the TV to an extremely
low level, without losing out on the
constant standby functionality.
ECO-Green
Power management (Available in selected
models only)
The advanced power management of this TV
ensures the most efficient use of its energy.
You can check how your personal TV settings,
the level of brightness in current onscreen
pictures and the surrounding light conditions
determine the relative power consumption.
End of use
To inform yourself on the correct disposal
of the TV and batteries, refer to ‘Disposal of
your old product and batteries’ in the user
manual (see ‘Disposal of your old product and
batteries’ on page 5).
•
•
•
High energy efficiency
Low standby power
Designed to facilitate recycling
Philips continuously focuses on lowering
the environmental impact of its innovative
consumer products. We aim our efforts
towards environmental improvements
during manufacturing, reduction of harmful
substances, energy-efficient use, end-of-life
instructions and product recycling.
Thanks to our environmental effort, this TV
has been awarded the European Ecolabel –the
You can find detailed information on standby
energy consumption, warranty policy, spare
parts and recycling of this TV on the Philips
This TV has features that contribute to
energy-efficient use. This TV was awarded
the European Ecolabel for its environmental
qualities.
Energy efficiency features
•
Ambient light sensor (Available in
selected models only)
To save energy, the built-in Ambient
light sensor lowers the brightness of the
TV screen when the surrounding light
darkens.
•
Energy saving
The energy saving setting of the TV
combines several TV settings that result
in saving energy. See the smart settings in
the setup menu.
6
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote control
3 YourTV
1
2
3
4
5
Congratulations on your purchase, and
welcome to Philips!To fully benefit from the
support that Philips offers, register yourTV at
22
21
20
6
7
This section gives you an overview of
commonly usedTV controls and functions.
19
8
9
18
17
Side controls and indicators
10
11
1
2
3
16
12
13
14
4
15
5
a
b
+/-: Increases or decreases volume.
(Home): Toggles the home menu on
or off.
c P/CH +/-: Switches to the next or
previous channel.
d
(Power): Switches the product on
or off. The product is not powered
off completely unless it is physically
unplugged.
e Standby indicator and remote control
sensor.
EN
7
Download from Www.Somanuals.com. All Manuals Search And Download.
a
b
(Standby-On)
o
p
q
SOUND (Smart Sound)
•
•
Switches the TV to standby if it is on.
Switches on the TV if it is in standby.
Launches the sound menu.
+/- (Volume +/-)
Increases or decreases volume.
MENU
Toggles the main menu on or off.
BACK P/P (Previous channel)
c MHEG/TELETEXT
•
•
Returns to a previous screen.
Returns to the previously viewed
channel.
Toggles teletext on or off.
d
SOURCE
Selects connected devices.
r
GUIDE
Switches between channel grid and
programme list.
e Colour buttons
Selects tasks or options.
s SUBTITLE (For RF Digital TV only)
f AD (Audio Descriptor) (For RF Digital
TV only)
Enables or disables subtitles.
UK only: Enables audio commentary for
the visually handicapped.
t DEMO (Used in selected models only)
Toggles the demonstration menu on or
off.
g
OPTIONS
Accesses options relating to the current
activity or selection.
u
FORMAT
Selects a picture format.
h OK
Confirms an entry or selection and
v
INCR. SURR
Enables Incredible Surround for stereo
sources. Enables spatial mode for mono
sources.
displays the channel grid, when watching
TV.
i
j
(Navigation buttons)
Remote control usage
When using the remote control, hold it close
to the TV and point it at the remote control
sensor. Make sure that the line-of-sight
between the remote control and TV is not
blocked by furniture, walls or other objects.
Navigates menus.
INFO
Displays program information, when
available. If the information spans multiple
pages, press OPTIONS to go to the next
page.
k
(Mute)
Mutes or restores volume.
l P +/- (Programme +/-)
~5m
~30˚
Switches to the next or previous channel.
When the TV menu is on, this functions
as Page Up / Down.
m 0-9 (Numeric buttons)
Selects a channel or setting.
n
PICTURE (Smart picture)
Launches the picture menu.
8
EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Switch channels
4 Use yourTV
•
Press P +/- on the remote control or
P/CH +/- on the side of the TV.
Enter a channel number using the
Numeric buttons.
This section helps you perform basicTV
operations.
•
•
•
Press OK to use the channel grid.
Press
BACK P/P on the remote
Switch yourTV on / off or to
standby
control to return to the previous channel.
Note
• When you use a favourite list, you can only
select those channels in the list (see ‘Select a
favourite list’ on page 16).
Switch channels with the channel grid
The channel grid allows you to view all
available channels in a grid format.
To switch on
•
If the standby indicator is off, press
(Power) at the side of the TV.
•
If the standby indicator is red, press
(Standby-On) on the remote control.
To switch to standby
•
Press (Standby-On) on the remote
control.
» The standby indicator switches to red.
1 Press OK.
» The channel grid appears.
2 Press
to select and preview a
To switch off
channel.
•
Press (Power) at the side of the TV.
3 Press OK to watch the selected channel.
» The standby indicator switches off.
Tip
• Though your TV consumes very little power
when in standby, energy continues to be
consumed. When not in use for an extended
period of time, disconnect the TV power cable
from the power outlet.
Note
• If you cannot locate your remote control and
want to switch on the TV from standby, press
P/CH +/- on the side of the TV.
EN
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Watch connected devices
Use teletext
Note
• Switch on the device before selecting it as a
source on the TV.
Use the source button
1 Press MHEG/TELETEXT.
» The main index page appears.
2 Select a page as follows:
•
•
•
•
Press the Numeric buttons to enter
a page number
Press P +/- to view the next or
previous page
Press the Colour buttons to select a
colour coded item
1 Press
SOURCE.
» The source list appears.
Press
BACK to return to a
2 Press
to select a device.
previously viewed page
3 Press OK to confirm your choice.
» TheTV switches to the selected
device.
3 Press MHEG/TELETEXT to exit teletext.
Note
• For UK users only: Some digital TV channels
offer dedicated digital text services (for
example, BBC1).
AdjustTV volume
To increase or decrease volume
•
Press
+/-.
To mute or unmute sound
•
•
Press to mute the sound.
Press again to restore the sound.
10 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Rename devices from the
home menu
5 Use more of
yourTV
After adding a new device to the home menu,
you can rename it to your preference.
1 Press MENU.
AccessTV menus
2 Press
to select a device to rename.
Menus help you to install channels, change
picture and sound settings and access other
features.
3 Press OPTIONS.
» The options menu appears.
4 Press
to select [Rename device], then
press OK.
» A text input box appears.
1 Press MENU.
» The menu screen appears.
5 Press
to select characters.
6 Press OK to confirm each character.
Add new device
Setup
Watch TV
7 Select [Done], then press OK to finish
renaming devices.
Note
• The device name can be up to 16 characters
long.
• Press [Aa] to change an uppercase letter to a
lowercase letter and vice versa.
2 Press
to select and navigate
through one of the following menus.
•
[Watch TV]: Switches back to the
aerial source if another source is
selected.
Remove devices from the
home menu
•
•
[Add new device]: Adds new devices
to the home menu.
[Setup]: Accesses menus to change
picture, sound and other settings.
If a device is no longer connected to theTV,
remove it from the home menu.
1 Press MENU.
3 Press OK to confirm your choice.
2 Press
to select a device to remove.
4 Press MENU to exit.
3 Press OPTIONS.
4 Press
to select [Remove device], then
Tip
press OK.
• After selecting [Add new device], follow the
on-screen instructions to select the correct
device and connector.
5 Select [Remove], then press OK.
» The selected device is removed from
the home menu.
EN 11
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
[Energy saving]: Applies low-energy
settings.
[Natural]: Applies the best picture
quality.
[Custom]: Lists customised picture
settings.
Change picture and sound
settings
Change picture and sound settings to suit your
preferences.You can apply pre-defined settings
or change settings manually.
3 Press OK to confirm your choice.
» The selected smart picture setting is
applied.
Note
• When watching TV or using external devices,
press OPTIONS then select [Picture and
sound] for quick access to picture and sound
settings.
Manually adjust picture settings
1 Press MENU.
2 Press
to select [Setup] >
Use settings assistant
[Picture].
3 Press
to select the following
Use the settings assistant to guide you through
the picture and sound settings.
settings.
•
[Smart picture]: Accesses pre-defined
smart picture settings.
[Video contrast]: Adjusts the intensity
of video contents, keeping backlight
unchanged.
1 Press MENU.
2 Press
to select [Setup] > [Picture]
•
> [Settings assistant].
3 Press OK.
» The [Settings assistant] menu appears.
Follow the on-screen instructions to
choose your preferred picture settings.
•
•
[Contrast]: Adjusts the intensity of
backlight areas, keeping video contents
unchanged.
[Brightness]: Adjusts the intensity and
details of dark areas.
Use smart picture
Use smart picture to apply pre-defined
picture settings.
•
•
•
[Colour]: Adjusts colour saturation.
[Hue]: Compensates for colour variations.
[Sharpness]: Adjusts sharpness in the
image.
1 Press PICTURE.
•
•
•
[Noise reduction]: Filters and reduces
noise in an image.
[Tint]: Adjusts the colour balance in an
image.
[Custom tint]: Customises tint setting.
(Only available if [Tint] > [Custom] is
selected)
[Digital Crystal Clear]: Fine-tunes each
pixel to match surrounding pixels. This
produces a brilliant, high-definition image.
» The [Smart picture] menu appears.
2 Press
to select one of the following
settings.
•
•
•
[Personal]: Applies the settings set in
[Settings assistant] menu.
[Vivid]: Applies rich and dynamic
settings.
[Standard]: Adjusts picture settings
to suit most environments and types
of video.
•
•
[Dynamic contrast]: Enhances
contrast. A [Medium] setting is
recommended.
•
•
[Cinema]: Applies settings for movie
viewing.
[Game]: Applies settings for games.
12 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
[Dynamic backlight]: Adjusts
brightness of the TV backlight to
match lighting conditions.
[MPEG artifact reduction]:
Smoothes out transitions on digital
pictures. You can switch this feature
on or off.
[Colour enhancement]: Makes
colours more vivid and improves
the details in bright colours. You can
switch this feature on or off.
[Auto format]: (Not for
PC mode.) Enlarges the
picture automatically to
best fit the screen. The
subtitles remain visible.
[Super zoom]: (Not
for HD and PC mode.)
Removes the black bars on
the side of 4:3 broadcasts.
There is minimal
•
distortion.
•
[PC mode]: Adjusts the picture when a
PC is connected to the TV via HDMI or
DVI.
[4:3]: Shows the classic 4:3
format.
•
•
[Picture format]: Changes the picture
format.
[Subtitle zoom]: Displays
4:3 pictures over the full
area of the screen, with
sub-titles visible. Part of
the top of the picture is
clipped off.
[Movie expand 14:9]: (Not
for HD and PC mode.)
Scales 4:3 format to 14:9.
[Picture size]: Adjusts the viewing area.
(when set to maximum, you might see
noise or a rough edge of an image.)
[Horizontal shift]: Adjusts the picture
horizontally for PC-VGA, DVI, HDMI or
YPbPr.
[Vertical shift]: Adjusts the picture
vertically for PC-VGA, DVI, HDMI or
YPbPr.
•
•
[Movie expand 16:9]:
(Not for HD and PC
mode.) Scales 4:3 format
to 16:9.
[Wide screen]: Scales 4:3
format to 16:9.
Change picture format
1 Press
FORMAT.
» A picture format bar appears.
2 Press
to select a picture format.
» The selected picture format is
activated.
[Unscaled]: For HD
and PC mode only,
and in selected models
only. Allows maximum
sharpness. Some
distortion may be present
due to the broadcaster’s
systems. Set your PC
resolution to wide screen
mode for best results.
3 Press OK to confirm your choice.
Summary of picture formats
The following picture settings can be
configured.
Note
• Depending on the format of the picture
source, some picture settings are not available.
EN 13
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
[Balance]: Adjusts the balance of the right
and left speakers.
[Audio language]: Available for digital
channels, when multiple languages are
broadcast. Lists available audio languages.
[Dual I-II]: Selects audio languages if dual
sound broadcast is available.
[Mono/Stereo]: Selects mono or stereo if
stereo broadcast is available.
[TV speakers]: Turns TV speakers on or
off. (Only available if EasyLink is switched
on.)
Use smart sound
Use smart sound to apply pre-defined sound
settings.
1 Press SOUND.
» The [Smart sound] menu appears.
•
•
•
2 Press
to select the following settings.
•
•
[Custom]: Applies the settings that
were customised in the sound menu.
[Standard]: Adjusts sound settings
to suit most environments and types
of audio.
•
•
[Surround]: Enables spatial sound.
[Headphone volume]: Adjusts headphone
volume.
•
•
[News]: Applies settings for spoken
audio, such as news.
[Movie]: Applies settings for movies.
•
[Auto volume levelling]: Automatically
reduces sudden volume changes, for
example, when switching channels.
[Delta volume]: Levels out volume
differences between channels or
connected devices. Switch to the
connected device before you change the
delta volume.
3 Press OK to confirm your choice.
» The selected smart sound setting is
applied.
•
Manually adjust sound settings
1 Press MENU.
•
[SPDIF OUT]: Selects the type of digital
audio output through SPDIF connector.
2 Press
to select [Setup] > [Sound].
» The [Sound] menu appears.
•
[PCM]: Converts non-PCM audio
type to PCM format.
[Multichannel]: Outputs audio to the
home theater.
3 Press
to select the following
settings.
•
•
[Smart sound]: Accesses pre-defined
smart sound settings.
•
•
•
[Bass]: Adjusts the bass level.
[Treble]: Adjusts the treble level.
[Digital audio lipsync]: Enables or disables
lipsync audio output. When this is
enabled, the TV synchronises the audio
and video performance. When disabled,
you need to adjust the lipsync audio
feature on the external device that is
connected to the TV. (Only available with
SPDIF connection)
•
•
[Volume]: Adjusts the volume.
[Vol.vis.impaired]: Sets the mix of visually
impaired audio with regular audio. When
available, visually impaired audio includes
audio descriptions of on-screen action.
You can also enable this by pressing AD
(Audio Descriptor). (Only applicable for
the UK region.)
14 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the universal access
menu
Use advanced teletext
features
You can activate the universal access menu
during the first installation. Once enabled, you
can quickly access the visually impaired and
hearing impaired menus when watching TV or
external devices.
Access the teletext options menu
Access the teletext features through the
teletext options menu.
1 Press MHEG/TELETEXT.
» The teletext screen appears.
Tip
2 Press OPTIONS.
• You can also enable the universal access
menu by selecting [Setup] > [Installation] >
[Preferences] > [Universal access] > [On].
» The teletext options menu appears.
3 Press
to select one of the following
options.
1 When watching TV, press OPTIONS.
•
•
•
[Reveal]: Hides or reveals hidden
information on a page, such as
solutions to riddles or puzzles.
[Cycle subpage]: Cycles through
subpages automatically if subpages
are available.
[Language]: Switches to a different
language group to display a language
correctly when it uses a different
character set.
» TheTV options menu appears.
2 Select [Universal access], then press OK
or to enter.
3 Press
to select one of the following
options and press OK to enter.
•
[Hearing impaired]: Enables or
disables hearing impaired subtitles.
[Visually impaired]: Selects speaker,
headphone or both for [Vol.vis.
impaired] audio. Select [Off] to
disable audio descriptor. (Only
applicable to the UK region).
•
•
•
[Freeze page]: Freezes the current
page.
[Dual screen] / [Full Screen]: Enables
and disables dual screen teletext.
•
[Vol.vis.impaired]: Adjusts the
volume of visually impaired audio.
4 Press
to make a selection, then
press OK to confirm.
5 Press
BACK to exit the teletext
Tip
options menu.
• Press the colour buttons on the remote
control to enter the options.
Select teletext subpages
A teletext page can hold several subpages.
Subpages are displayed on a bar next to the
main page number.
1 Press MHEG/TELETEXT.
» The teletext screen appears.
2 Press P +/- to select a teletext page.
3 Press
to enter a subpage.
EN 15
Download from Www.Somanuals.com. All Manuals Search And Download.
SelectT.O.P. teletext broadcasts
Create and use list of
favourite channels
Table Of Pages (T.O.P.) teletext broadcasts
allow you to jump from one subject to
another without using page numbers. T.O.P.
teletext is not broadcast on all TV channels.
You can create a list of your preferredTV
channels so that you can find those channels
easily.
1 Press MHEG/TELETEXT.
» The teletext screen appears.
Select a favourite list
2 Press INFO.
» TheT.O.P. overview appears.
1 When watching TV, press OK to display
the channel grid.
3 Press
to select a subject.
2 Press OPTIONS.
4 Press OK to view the page.
» The channel options menu appears.
3 Press
to select [Select list], then
UseTeletext 2.5
press OK to enter.
Teletext 2.5 offers more colours and better
graphics than normal teletext. If Teletext 2.5
is broadcast by a channel, it is switched on by
default.
» The channel list options appear.
4 Select [Favourite], then press OK.
» Only channels in the favourite list
appear in the channel grid.
1 Press MENU.
2 Press
to select [Setup] >
Note
[Installation] > [Preferences] > [Teletext
• The favourite channel grid is empty until you
add channels into the favourite lists.
2.5].
3 Press
to select [On] or [Off].
4 Press OK to confirm your choice.
View all channels
You can exit a favourite list, and view all
installed channels.
1 When watching TV, press OK.
» The channel grid appears.
2 Press OPTIONS.
» The channel options menu appears.
3 Press
to select [Select list], then
press OK or to enter.
4 Select [All], then press OK.
» All channels are displayed in the
channel grid.
Note
• All favourite channels are marked by an
asterisk when you view the channel grid.
16 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Add a channel to a favourite list
Use the Electronic
Programme Guide
Tip
EPG is an on-screen guide available for digital
channels. EPG allows you to:
• View all channels before adding a channel to a
favourite list.
•
View a list of digital programmes being
broadcast
View upcoming programmes
Group programmes by genre
Set reminders when programmes start
Set up preferred EPG channels
1 When watching TV, press OK.
» The channel grid appears.
•
•
•
•
2 Press
to select a channel to add to
a favourite list.
3 Press OPTIONS.
» The channel options menu appears.
Switch on EPG
4 Select [Mark as favourite], then press
1 When watching TV, press GUIDE.
» The EPG planner screen appears
displaying information about the
scheduled programmes.
OK.
» The channel is added to the favourite
list.
Note
Note
• All favourite channels are marked by an
asterisk in the channel grid.
• EPG data is available only in selected countries
and can take some time to load.
Remove a channel from a favourite
list
Use EPG
1 When watching TV, press GUIDE.
1 When watching TV, press OK.
» The EPG planner screen appears.
» The channel grid appears.
2 Press MENU.
2 Press
to select a channel to
» The program guide menu appears.
remove.
3 Press
to select an option, and then
3 Press OPTIONS.
press OK to confirm.
4 Select [Unmark as fav.], then press OK.
4 Press MENU to exit the EPG menu.
» The channel is removed.
Note
• Only the channels in the [Preferred EPG
channels] list appear in the EPG menu.
EN 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Use the EPG options menu
Use the EPG options menu to set or clear
reminders, change day and access other useful
EPG options.
3 Press
to enter time.
4 Select [Done] to confirm.
5 Press MENU to exit.
Note
1 Press GUIDE.
2 Press OPTIONS.
• If your selected country supports digital
broadcast, the clock displays the time data
from your TV service operator as priority.
» The EPG menu appears.
3 Press
to select one of the following
options.
•
[Set remind] / [Clear remind]: Sets
or clears programme reminders.
[Change day]: Sets the EPG day.
[Show info]: Displays programme
information.
Display theTV clock
1 When watching TV, press OPTIONS.
•
•
» TheTV option menu appears.
2 Select [Clock].
•
•
[Search by genre]: Searches TV
programmes by genre.
[Scheduled reminders]: Lists
programme reminders. Only
available for upcoming programmes.
[Preferred EPG channels]: Sets
preferred EPG channels.
3 Press OK.
Note
• To disable the clock, repeat the above
procedure.
•
4 Press OK to enter or activate the option.
Change the clock mode
5 Press
BACK to exit the EPG menu.
1 Press MENU.
Tip
2 Press
to select [Setup] >
• Press GUIDE to switch between EPG and
[Installation] > [Clock] > [Auto clock
channel grid.
mode].
3 Press
to select [Automatic] or
[Manual].
4 Press OK to confirm.
Use theTV clock
You can display a clock on theTV screen.The
clock displays the current time using time data
received from yourTV service operator.
Change the time zone
1 Press MENU.
2 Press
to select [Setup] >
[Installation] > [Clock] > [Time zone].
to select your time zone.
Set theTV clock manually
In some countries, you need to set TV clock
manually.
3 Press
4 Press OK to confirm.
1 Press MENU.
Note
2 Select [Setup] > [Features] > [Clock].
• This option is only available if you select [Auto
clock mode] > [Manual] (in countries with
clock transmission data).
» The [Clock] menu appears.
18 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Use daylight saving
4 Press OK to switch on the sleep timer.
» TheTV switches to standby after the
specified time.
1 Press MENU.
2 Press
to select [Setup] >
[Installation] > [Clock] > [Daylight
saving].
Automatically switch theTV on (on
timer)
You can switch on the TV from standby to a
specific channel at a specified time.
3 Press OK or to enter [Daylight saving].
4 Press
to select [Standard time] or
[Daylight saving time].
5 Press OK to confirm.
1 Press MENU.
2 Press
to select [Setup] >
Note
[Features] > [On timer].
• This option is only available if you select
3 Press to enter the [On timer] menu.
[Auto clock mode] > [Manual].
•
•
•
[Activate]: Selects how often the TV
is switched on.
[Time]: Sets the time to switch on
the TV.
[Programme no.]: Selects the
channel or the connected device.
Use timers
You can set timers to switch theTV to standby
at a specified time.
4 Press MENU to exit.
Tip
Tip
• Select [On timer] > [Activate] > [Off] to
• Set the TV clock before you use timers.
disable this feature.
Automatically switch theTV to
standby (sleep timer)
Sleep timer switches the TV to standby after a
pre-defined period of time.
Tip
• You can switch off your TV earlier or reset the
sleep timer during the countdown.
1 Press MENU.
2 Press
to select [Setup] >
[Features] > [Sleep timer].
» The [Sleep timer] menu appears.
3 Press
to select a value between zero
and 180 minutes.
» The sleep timer can be set in steps of
five minutes. If set to zero, the sleep
timer is switched off.
EN 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Lock or unlock one or more channels
UseTV locks
You can prevent your children from watching
certain programmes or channels by locking the
TV controls.
1 When watching TV, press OK to display
the channel grid.
2 Press
to select a channel to lock or
unlock.
3 Press OPTIONS.
Set or change your PIN code
4 Press
to select [Lock channel] or
1 Press MENU.
[Unlock channel].
2 Press
to select [Setup] >
5 For each selection, press OK to lock or
[Features] > [Set code] / [Change code].
» The [Set code] / [Change code] menu
appears.
unlock the channel.
» The first time you lock or unlock a
channel, you are prompted to enter
your PIN code.
3 Enter your code using the Numeric
buttons.
6 Enter your code and press OK.
» If the channel is locked, a lock icon is
displayed.
» Follow the on-screen instructions to
create or change your PIN code.
Tip
7 Repeat the process to lock or unlock
more channels.
• If you forget your code, enter ‘8888’ to
override any existing codes.
Note
• Switch the TV off and on again for the change
to take effect.
Lock or unlock theTV
Lock the TV to prevent access to all channels
and connected devices.
• If you use P +/- on your remote control to
switch between channels, the locked channels
are skipped.
• If you access the locked channels from the
channel grid, you are prompted to enter your
PIN code.
1 Press MENU.
2 Press
to select [Setup] >
[Features] > [TV lock].
» You are prompted to enter your PIN
code.
Set parental ratings
Some digital broadcasters rate their
programmes according to age. You can set
your TV to display only programmes with age
ratings higher than your child’s age.
3 Enter your code using Numeric buttons.
» The [TV lock] menu appears.
4 Press
to select [Lock] or [Unlock].
5 Press OK to confirm.
1 Press MENU.
» All channels and connected devices are
locked or unlocked.
2 Press
to select [Setup] >
[Features] > [Parental rating].
6 Press MENU to exit.
» A code setup screen appears.
Note
3 Enter your code using Numeric buttons.
» The parental rating menu appears.
• Switch the TV off and on again for the change
to take effect.
4 Press
to select an age rating.
5 Press OK to confirm.
• If you select [Lock], you have to enter your
code every time you turn on your TV.
6 Press MENU to exit.
20 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Select a subtitle language on digitalTV
channels
Use subtitles
You can enable subtitles for eachTV channel.
Subtitles are broadcast via teletext or DVB-T
digital broadcasts.With digital broadcasts, you
can select a subtitle language.
Note
• When you select a subtitle language on
a digital TV channel as described below,
the preferred subtitle language set in the
installation menu is temporarily overruled.
Enable subtitles on analogueTV
channels
1 Press MENU.
1 Select an analogue TV channel.
2 Press
to select [Setup] >
[Features] > [Subtitle language].
2 Press MHEG/TELETEXT.
3 Press OK or to enter the list of
3 Enter the three-digit page number of the
available languages.
subtitle page with the Numeric buttons.
4 Press
to select a subtitle language.
5 Press OK to confirm.
4 Press MHEG/TELETEXT to switch off
teletext.
5 Press SUBTITLE.
Tip
» The [Subtitle mode] menu appears.
• You can also access the [Subtitle language]
menu while watching TV by pressing
OPTIONS > [Subtitle language].
6 Select [On] to display subtitles always or
[On during mute] to display subtitles only
when audio is muted.
7 Press OK to enable subtitles.
8 Repeat this procedure to enable subtitles
on each analogue channel.
Tip
• Select [Subtitle mode] > [Off] to disable
subtitles.
Enable subtitles on digitalTV channels
1 When watching digital channels, press
SUBTITLE.
» The [Subtitle mode] menu appears.
2 Select [On] to display subtitles always or
[On during mute] to display subtitles only
when audio is muted.
3 Press OK to enable subtitles.
EN 21
Download from Www.Somanuals.com. All Manuals Search And Download.
View a slide show of your photos
View photos and play music
from a USB storage device
1 When a full screen image of a photo is
displayed, press OK.
Caution
» A slide show begins from the selected
photo.
• Philips is not responsible if the USB storage
device is not supported, nor is it responsible
for damage or loss of data from the device.
2 Press the following buttons to control the
slide show:
•
•
OK to pause the slide show.
to go back or move forward to
the next image.
Use the USB connector to view photos or
listen to music stored on a USB storage device.
1 Turn on the TV.
•
BACK to stop the slide show.
2 Connect the USB storage device to the
TV.
Change slide show settings
» The home menu appears.
1 When viewing a slide show, press
3 Press
to select [Browse USB].
4 Press OK to confirm.
OPTIONS.
» The slide show options menu appears.
» The USB thumbnail browser appears.
2 Press
to select one of the following.
Tip
•
•
[Start Slideshow] / [Stop Slideshow]:
Starts or stops a slide show.
[Slideshow transitions]: Sets the
transition from one picture to the
next.
• Press GUIDE to switch between thumbnail
and file browsing views.
•
[Slideshow frequency]: Sets the
amount of time that a picture is
shown.
View photos
1 In the USB browser, press to enter the
•
•
[Rotate image]: Rotates a picture.
[Show info]: Displays the picture
name, date, size and next picture in
the slide show.
[Picture] folder.
2 Press
to select a photo or a photo
album.
3 Press OK to view a full screen image of
3 Press OK to confirm your setting.
the photo.
Note
Tip
• [Rotate image] and [Show info] appear only
• When in full screen mode, press
between photos.
to move
when you press OK to pause the slideshow.
22 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Listen to music
Disconnect a USB storage device
1 In the USB thumbnail browser view,
Caution
select [Music] and press to enter.
•
Press GUIDE to switch between
thumbnail and file browsing views.
• Follow this procedure to avoid damage to your
USB storage device.
2 Press
to select a music track or
1 Press
BACK to exit the USB browser.
2 Wait for five seconds then disconnect the
album.
3 Press OK to play the selected music.
USB storage device.
Button
Function
OK
Pause, resume play or stop
playback.
Listen to digital radio
channels
/
Go to the previous or next
music.
If digital broadcasting is available, digital radio
channels are installed automatically during
installation.
Music settings
1 When watching TV, press OK to display
When listening to music, press OPTIONS
to access one of the following music settings.
the channel grid.
•
•
[Start playback] / [Stop playback]: Starts
or stops the music.
[Repeat] / [Play once]: Repeats a song. /
Disables repeat play and plays a song or
album once.
2 Press OPTIONS.
3 Press
to select [Select list] > [Radio].
» The radio channel grid appears.
4 Press
to select a radio channel and
press OK to listen.
•
[Shuffle on] / [Shuffle off]: Enables or
disables random play of songs.
[Show info]: Displays the file name.
[TV speakers]: Sets the TV speakers
on or off. (Only available if EasyLink is
switched on.)
Note
•
•
• Select [Select list] > [All] to exit radio
channels and view all channels.
•
[Sound]: Adjusts the sound setting.
View a slideshow with music
You can view a picture slide show with
background music.
1 Select an album of songs.
2 Press OK.
3 Press
BACK to return to the USB
content browser.
4 Select an album of pictures.
5 Press OK.
EN 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Update using OAD
Update theTV software
Philips continuously tries to improve its
products and we recommend that you update
theTV software when updates are available.
1 If using (DVB-T) digital broadcast, your
TV automatically receives software
updates. If you receive a message on
your screen asking you to update your
software:
•
Select [Update now] to update the
software immediately.
Check the current software version
•
Select [Remind me later] to exit the
update screen at that time and be
reminded later.
1 Press MENU.
2 Press
to select [Setup] >
•
Select [Cancel] to skip the update.
[Software update] > [Current software
info].
2 If you select [Cancel], you can manually
access the OAD update by selecting
[Setup] > [Software update] > [Local
updates] > [OAD].
» TheTV displays the current software
information.
3 Select the available version of OAD and
Download the software
press OK.
1 On your PC, open a web browser and go
4 Follow the on-screen instructions to start
the update.
2 Download the latest software upgrade
file to your PC.
Note
3 Decompress the ZIP-file.
• The TV restarts after the software update is
complete.
4 Copy the autorun.upg file to the root
directory of the USB device.
Update software
ChangeTV preferences
You can update the TV software via a USB
storage device or OAD (Over the Air
software Download).
Use the preferences menu to customise your
TV settings.
1 Press MENU.
Update using a USB device
Connect your USB storage device to the TV.
1 If the software update screen does not
appear automatically, select [Setup] >
[Software update] > [Local updates] >
[USB].
2 Select [Setup] > [Installation] >
[Preferences].
•
•
•
[Location]: Optimises TV settings for
your location - home or shop.
[Volume bar]: Displays the volume
bar when you adjust the volume.
[Channel info.]: Displays information
about the TV channel every time you
switch channels. Select [Full] to view
channel information or [Off] to turn
off the channel information.
2 Press OK to update the TV software
manually.
3 Follow the on-screen instructions to
complete the update.
Note
•
[Universal access]: Enables or
disables the universal access menu.
• The TV restarts after the software update is
complete.
24 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
[EasyLink]: Enables one-touch play
and one-touch standby between
EasyLink-compliant devices.
[Pixel Plus Link]: Overrides the
settings of connected devices and
uses the settings of the TV. (Only
available if EasyLink is switched on.)
[Teletext 2.5]: Enables or disables
Teletext 2.5. (For digital TV)
8 Press OK.
9 Press MENU to exit.
Note
• Select [None] if you do not want to map to
the decoder / descrambler channel.
•
•
[E-sticker]: For shop mode only. Sets
the location of the e-sticker.
Start aTV demo
3 Press
to select your preference.
You can use demonstrations to better
4 Press OK.
understand the features of your TV. Some
demos are not available on certain models.
Available demos are displayed in the menu list.
5 Press MENU to exit.
1 Press DEMO on the remote control.
Access decoder channel
2 Press
to select a demo and press OK
to view it.
3 Press DEMO to exit.
You can map channels provided through a
decoder or descrambler to yourTV channel
selection. In this way, you can select these
channels by using the RC of yourTV.The
decoder or a descrambler must be connected
to EXT1 (SCART).
Reset theTV to factory
settings
You can restore the default picture and sound
settings of yourTV.The channel installation
settings remain the same.
Set decoder channel
Map channels from a decoder or descrambler.
1 Press MENU.
1 Press MENU.
2 Select [Setup] > [Installation] >
2 Select [Setup] > [Installation] > [Factory
[Decoder].
settings].
3 Press to enter [Decoder] menu.
3 Press to enter [Factory settings].
4 Select [Reset] to start resetting.
5 Press OK.
4 Press
to select [Channel], then press
to enter.
5 Select one channel to map to the
decoder / descrambler channel and press
OK to confirm.
6 Press MENU to exit.
6 Select [Status], then press to enter.
7 Select [EXT 1] (SCART) the connector
used by the decoder / descrambler.
EN 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Step 3 Install channels
Automatically installs the available analogue
and digital TV channels and digital radio
channels.
6 Install channels
The first time you set up yourTV, you are
prompted to select a menu language and to
installTV and digital radio channels (if available).
This chapter provides instructions on how to
re-install and fine tune channels.
1 From the channel installation guide
screen, select [Full installation].
2 Press OK to confirm.
» TheTV starts to search and store all
the available channels.
3 When installation is complete, press OK
Automatically install channels
to exit the installation menu.
This section describes how to search and store
channels automatically.
Update the channel list
You can enable automatic update of channels
when your TV is in standby mode. The
channels stored in your TV are updated every
morning according to the channel information
in the broadcast.
Step 1 Select your menu language
1 Press MENU.
2 Press
to select [Setup] >
[Installation] > [Language] > [Menu
1 Press MENU.
language].
2 Press
to select [Setup] >
3 Press OK or to enter [Menu language].
[Installation] > [Channel installation] >
4 Press
to select a language.
5 Press OK to confirm.
[Standby update].
3 Select [On] to enable the automatic
update or select [Off] to disable it.
6 Press to return to [Installation] menu.
Step 2 Select your country
Select the country where you are installing the
TV. The available channels for the country are
installed on the TV.
1 Press MENU.
2 Press
to select [Setup] >
[Installation] > [Channel installation] >
[Automatic channel search].
3 Press OK or to enter the menu.
» The country menu appears.
4 Press
to select your country.
5 Press OK to confirm your choice.
» The channel installation guide appears
on the screen.
26 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Manually install channels
6 Press
BACK when the new channel is
found.
This section describes how to search and store
analogueTV channels manually.
7 Press
to select [Store as new
channel] to store the new channel under
a new channel number.
Step 1 Select your system
8 Press OK to enter [Store as new
channel], then press OK.
Note
9 Press to return to the [Channel
installation] menu.
• Skip this step if your system settings are
correct.
Step 3 Fine-tune analogue channels
1 Press MENU.
1 Press MENU.
2 Press
to select [Setup] >
2 Press
to select [Setup] >
[Installation] > [Channel installation] >
[Analogue: manual install].
» The [Analogue: manual install] menu
appears.
[Installation] > [Channel installation] >
[Analogue: manual install].
» The [Analogue: manual install] menu
appears.
3 Press
to select [System], then press
3 Press
to select [Fine-tune], then
press to enter.
to adjust frequency.
to enter.
4 Press
to select your country or
4 Press
region.
5 Press OK to confirm.
5 Press OK to confirm.
6 Press
to select [Store current
6 Press to return to [Channel
channel] to store the channel number.
installation] menu.
7 Press to enter [Store current channel],
then press OK.
Step 2 Search and store newTV
channels
8 Press to return to the [Channel
installation] menu.
1 Press MENU.
2 Press
to select [Setup] >
[Installation] > [Channel installation] >
[Analogue: manual install].
» The [Analogue: manual install] menu
appears.
3 Press
to select [Search], then press
to enter.
4 Press
to manually enter the three-
digit frequency.
5 Press OK to begin search.
» If a channel is unavailable at the
selected frequency, press OK to search
for the next available channel.
EN 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Rename channels
Test digital reception
You can rename channels.The name appears
when you select the channel.
You can check the quality and signal strength
of digital channels.This allows you to reposition
and test your antenna or satellite dish.
1 When watching TV, press OK to display
the channel grid.
1 Press MENU.
2 Select the channel to rename.
2 Press
to select [Setup] >
[Installation] > [Channel installation] >
3 Press OPTIONS.
[Manual channel search].
» The channel options menu appears.
3 Press to enter the menu.
4 Press
to select [Rename channel],
then press OK.
» A text input box appears.
4 Press
to enter the frequency of
the channel you want to test.
5 Press OK to confirm the frequency, then
5 Press
to select characters.
6 Press OK to confirm each character.
press OK again to confirm [Search].
6 When complete, select [Store] to store
7 Select [Done], then press OK to finish
the frequency.
renaming channels.
Note
Tip
• If the signal quality and strength is poor,
reposition the aerial or satellite dish and retest.
• If you still have problems with the reception
of your digital broadcast, contact a specialised
installer.
• Press [Aa] to change an uppercase letter to a
lowercase letter and vice versa.
Rearrange channels
After you install channels, you can rearrange the
order in which they appear.
1 When watching TV, press OK to display
the channel grid.
2 Press OPTIONS.
» The channel options menu appears.
3 Press
to select [Reorder], then press
OK.
4 Select the channel to rearrange, then
press OK.
» The selected channel is highlighted.
5 Press
to move the highlighted
channel to the desired location, then
press OK.
6 Press OPTIONS.
» [Done reordering] appears on the
screen.
7 Press OK to confirm.
8 Press
BACK to exit the channel grid.
28 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
a TV ANTENNA
Signal input from an antenna, cable or
satellite.
7 Connect devices
This section describes how to connect devices
with different connectors. Examples are
provided in the Quick Start.
TV ANTENNA
Note
• You can use different types of connectors to
connect a device to your TV.
Back connector
b EXT 1 and EXT 2 (CVBS and RGB)
Analogue audio and video input from
analogue or digital devices such as DVD
players or game consoles.
c SPDIF OUT
Digital audio output to home theatres
and other digital audio systems.
SPDIF OUT
EN 29
Download from Www.Somanuals.com. All Manuals Search And Download.
d SERV. U
For use by service personnel only.
g EXT 3 (Y Pb Pr and AUDIO L/R)
Analogue audio and video input from
analogue or digital devices such as DVD
players or game consoles.
e PC IN (VGA and AUDIO IN)
Audio and video input from a computer.
VGA
VGA
AUDIO IN
LEFT/RIGHT
VGA/DVI
f HDMI 1
Digital audio and video input from high-
definition digital devices such as Blu-ray
players.
Connections via DVI or VGA require an
additional audio cable (see ‘Connect a
computer’ on page 32).
30 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
b VIDEO
Composite video input from analogue
devices such as VCRs.
Side connector
c USB
Data input from USB storage devices.
d HDMI
a AUDIO L/R
Digital audio and video input from high-
definition digital devices such as Blu-ray
players.
Audio input from analogue devices
connected to VIDEO.
e
(Headphone)
Stereo audio output to headphones or
earphones.
EN 31
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
DVI-HDMI cable
f COMMON INTERFACE
Slot for a Conditional Access Module
(CAM).
AUDIO IN
LEFT/RIGHT
VGA/DVI
DVI
Connect a computer
HDMI cable and HDMI-DVI adaptor
Before you connect a computer to theTV
•
Set the screen refresh rate on your
computer to 60Hz.
Select a supported screen resolution on
your computer.
AUDIO IN
LEFT/RIGHT
VGA/DVI
•
Connect a computer with one of the
following connectors:
Note
DVI
• Connections via DVI or VGA require an
additional audio cable.
•
HDMI cable
VGA cable
AUDIO IN
LEFT/RIGHT
VGA/DVI
VGA
32 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
Access CAM services
Use a Conditional Access
Module
1 After inserting and activating the CAM,
press MENU.
A Conditional Access Module (CAM) is
provided by digitalTV service operators to
decode digitalTV channels.
2 Press
to select [Setup] >
[Features] > [Common interface].
» Applications provided by the digitalTV
service operator appear on the screen.
Note
Note
• Refer to the documentation from your service
operator on how to insert a smart card into
the Conditional Access Module.
• This menu option is available only if the CAM
is inserted and activated correctly.
Insert and activate a CAM
Caution
• Be sure to follow the instructions described
below. Wrong insertion of a CAM may
damage both the CAM and your TV.
1 Switch off the TV and disconnect it from
the power outlet.
2 Following the directions printed on the
CAM, gently insert the CAM into the
COMMON INTERFACE at the side of
the TV.
3 Push the CAM in as far as it will go.
4 Reconnect the TV to the power outlet.
5 Turn on the TV and wait for the CAM
to be activated. This may take several
minutes. Do not remove the CAM from
the slot when in use — removing the
CAM will deactivate digital services.
EN 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Enable or disable EasyLink
Use Philips EasyLink
Note
Your TV supports Philips EasyLink, which
uses the HDMI CEC (Consumer Electronics
Control) protocol. EasyLink-compliant devices
that are connected through HDMI connectors
can be controlled by a single remote control.
• Do not enable Philips EasyLink if you do not
intend to use it.
1 Press MENU.
2 Press
to select [Setup] >
Note
[Installation] > [Preferences] >
• The EasyLink-compliant device must be
switched on and selected as the source.
• Philips does not guarantee 100%
[EasyLink].
3 Select [On] or [Off].
interoperability with all HDMI CEC devices.
Use one-touch play
1 After enabling EasyLink, press play on
EasyLink features
One-touch play
your device.
» TheTV automatically switches to the
correct source.
When you connect your TV to devices that
support one-touch play, you can control your
TV and the devices with one remote control.
One-touch standby
When you connect your TV to devices that
support standby, you can use your TV remote
control to put your TV and all connected
HDMI devices in standby mode.
System audio control
Use one-touch standby
1 Press (Standby-On) on the TV’s or
device’s remote control.
» TheTV and all connected HDMI
devices switch to standby.
When you connect your TV to HDMI
CEC compliant devices, your TV can
switch automatically to play audio from the
connected device.
To use one-touch audio, you must map the
audio input from the connected device to
your TV.
SetTV speakers to EasyLink mode
When you play content from an EasyLink
compliant home theater, the TV speakers are
automatically muted.
1 Enable one-touch play and one-touch
standby between your Easylink compliant
devices by following the instructions
in the previous section (see ‘Enable or
disable EasyLink’ on page 34).
You can use the remote control from the
connected device to adjust the volume.
2 Press MENU.
3 Press
to select [Setup] > [Sound]
> [TV speakers] > [Auto EasyLink].
» TheTV speakers are turned off
automatically when content from an
Easylink compliant system is detected.
34 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
4 Press
to select [Setup] > [Sound]
> [TV speakers] > [On] to disable
system audio control and enable the TV
speakers.
Note
• To mute the TV speakers, select [TV
speakers] > [Off].
Use a Kensington lock
There is a Kensington security slot at the back
of theTV. Prevent theft by looping a Kensington
lock between the slot and a permanent object,
such as a heavy table.
EN 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Multimedia
8 Product
information
•
Supported storage device: USB (Only
FAT or FAT 32 USB storage devices are
supported)
•
Supported multimedia file formats:
Product information is subject to change
without notice. For detailed product
•
•
Images: JPEG
Audio: MP3
Note
• Multimedia file names must not exceed 128
characters.
Supported display resolutions
Computer formats
•
Resolution - refresh rate:
•
•
•
•
•
•
•
•
640 x 480 - 60Hz
800 x 600 - 60Hz
1024 x 768 - 60Hz
1280 x 720 -60Hz
1280 x 768 -60Hz
1280 x 1024 - 60 Hz
1360 x 768 - 60Hz
1440 x 900 - 60Hz (For Full HD
only)
Tuner / Reception /
Transmission
•
•
•
Aerial input: 75 ohm coaxial (IEC75)
DVB: DVB Terrestrial, DVB-T MPEG4
TV system: DVB COFDM 2K/8K; PAL I,
B/G, D/K; SECAM B/G, D/K, L/L’
Video playback: NTSC, SECAM, PAL
Tuner Bands: Hyperband, S-channel, UHF,
VHF
•
•
•
1680 x 1050 - 60Hz (For Full HD
only)
Video formats
•
Resolution - refresh rate:
•
•
•
•
•
•
•
480i - 60Hz
Remote control
480p - 60Hz
576i - 50Hz
576p - 50Hz
720p - 50Hz, 60Hz
1080i - 50Hz, 60Hz
1080p - 24Hz, 25Hz, 30Hz, 50Hz,
60Hz.
•
•
Type: PF01E09B
Batteries: 2 x AAA (LR03 type)
Power
•
•
•
Mains power: 220-240V, 50Hz
Standby power: < 0.3 W
Ambient temperature: 5 to 40 degrees
Celsius
36 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
SupportedTV mounts
Product specification
To mount theTV, purchase a PhilipsTV mount
or aVESA-compatibleTV mount.To prevent
damage to cables and connectors, be sure to
leave a clearance of at least 2.2 inches or 5.5cm
from the back of theTV.
Design and specifications are subject to change
without notice.
32PFL3605H
•
Without TV stand
•
Dimension (WxHxD): 795.6 x 508.3
Warning
x 93 (mm)
• Follow all instructions provided with the TV
mount. Koninklijke Philips Electronics N.V.
bears no responsibility for improper TV
mounting that results in accident, injury or
damage.
•
Weight: 8.3 kg
•
With TV stand
•
Dimension (WxHxD): 795.6 x 556.6
x 220.8 (mm)
Weight: 9.4 kg
•
42PFL3605H
TV screen Required
Required
•
Without TV stand
size
(inches)
32
pitch (mm) mounting bolts
•
•
Dimension (WxHxD): 1018.5 x
635.7 x 83 (mm)
200 x 200
300 x 200
400 x 300
4 x M6 (≤ 10 mm)
4 x M6 (≤ 10 mm)
4 x M8 (≤ 12 mm)
Weight: 11.5 kg
42
47
•
With TV stand
•
•
Dimension (WxHxD): 1018.5 x 683
x 235.8 (mm)
Weight: 12.8 kg
47PFL3605H
•
Without TV stand
•
•
Dimension (WxHxD): 1129.8 x
700.7 x 83 (mm)
Weight: 16.8 kg
•
With TV stand
•
•
Dimension (WxHxD): 1129.8 x 746.4
x 270.1 (mm)
Weight: 19.8 kg
EN 37
Download from Www.Somanuals.com. All Manuals Search And Download.
Cannot remove ‘e-sticker’ banner displayed on
theTV.
9 Troubleshooting
•
To remove the logos and images, set the
location of your TV to home.
1. Press MENU.
2. Select [Setup] > [Installation] >
[Preferences] > [Location].
3. Select [Home] and press OK.
This section describes commonly encountered
issues and accompanying solutions.
GeneralTV issues
TV channel issues
TheTV does not switch on:
•
Disconnect the power cable from the
power outlet. Wait for one minute then
reconnect it.
Check that the power cable is securely
connected.
Previously installed channels do not appear in
the channel list:
•
Check that the correct channel list is
selected.
•
No digital channels were found during the
installation:
The remote control is not working properly:
•
Check that the remote control batteries
are correctly inserted according to the
+/- orientation.
•
Check that the TV supports DVB-T,
DVB-T Lite or DVB-C in your country.
Some channels are not automatically installed
on myTV:
•
•
Replace the remote control batteries if
they are flat or weak.
Clean the remote control and TV sensor
lens.
•
During installation, make sure that
you select the country where you are
installing the TV (see ‘Step 2 Select your
country’ on page 26).
The standby light on theTV blinks red:
•
Disconnect the power cable from the
power outlet. Wait until the TV cools
down before reconnecting the power
cable. If the blinking reoccurs, contact
Philips Consumer Care.
Picture issues
TheTV is on, but there is no picture:
•
Check that the antenna is properly
connected to the TV.
You forgot the code to unlock theTV lock
feature
•
Check that the correct device is selected
as the TV source.
•
Enter ‘8888’.
TheTV menu is in the wrong language.
There is sound but no picture:
•
•
Change the TV menu to your preferred
language.
Check that the picture settings are
correctly set.
When turning theTV on / off / to standby, you
hear a creaking sound from theTV chassis:
There is poorTV reception from an antenna
connection:
•
•
No action is required. The creaking sound
is normal expansion and contraction of
the TV as it cools down and warms up.
This does not impact performance.
Check that the antenna is properly
connected to the TV.
•
Loudspeakers, unearthed audio devices,
neon lights, high buildings and other large
objects can influence reception quality.
If possible, try to improve the reception
quality by changing the antenna direction
or moving devices away from the TV.
If reception on only one channel is poor,
fine tune this channel.
•
38 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
There is poor picture quality from connected
devices:
HDMI connection issues
There are problems with HDMI devices:
•
Check that the devices are connected
properly.
•
Note that HDCP (High-bandwidth Digital
Content Protection) support can delay
the time taken for a TV to display content
from a HDMI device.
•
Check that the picture settings are
correctly set.
TheTV did not save your picture settings:
•
•
If the TV does not recognise the HDMI
device and no picture is displayed, try
switching the source from one device to
another and back again.
Check that the TV location is set to the
home setting. This mode offers you the
flexibility to change and save settings.
The picture does not fit the screen; it is too
big or too small:
•
•
If there are intermittent sound
disruptions, check that output settings
from the HDMI device are correct.
If you use an HDMI-to-DVI adapter
or HDMI-to-DVI cable, check that an
additional audio cable is connected to
AUDIO IN (mini-jack only).
•
Try using a different picture format.
The picture position is incorrect:
•
Picture signals from some devices may
not fit the screen correctly. Check the
signal output of the device.
Computer connection issues
Sound issues
The computer display on theTV is not stable:
There is a picture but sound quality is poor:
•
Check that your PC uses the supported
resolution and refresh rate.
Note
•
Set the TV picture format to unscaled.
• If no audio signal is detected, the TV
automatically switches the audio output off
— this does not indicate malfunction.
Contact us
•
Check that all cables are properly
connected.
Check that the volume is not set to 0.
Check that the sound is not muted.
If you cannot resolve your problem, refer to
the FAQs for this product at
If the problem remains unresolved, contact
Philips Consumer Care in your country as
listed in the Addendum.
•
•
There is a picture but the sound quality is
poor:
•
Check that the sound settings are
correctly set.
There is a picture but sound comes from one
speaker only:
Warning
• Do not attempt to repair the product yourself.
This may cause severe injury, irreparable
damage to your product or void your
warranty.
•
Verify that sound balance is set to the
centre.
Note
• Make a note of your TV model and serial
number before you contact Philips. These
numbers are printed on the back of the TV
and on the packaging.
EN 39
Download from Www.Somanuals.com. All Manuals Search And Download.
computer
10 Index
connect
39, 32
36
display resolution
Conditional Access Module
connect
antenna
PC
connectors
back connectors
HDMI
33
A
29
39, 32
analogue
fine-tune
antenna
27
29
29
39, 29
29
B
overview
side connectors
USB
back connectors
batteries
29
36, 5
37
31
22
bracket for wall mount
content ratings
country
20
26
C
CAM
33
5
25
9
D
care
daylight saving
decoder
19
25
25
25
10
channel decoder
channel grid
channels
default settings
demo
devices
devices
favourites list
fine-tune
grid
install
16
27
9
add to home menu
connect
11
29
11
11
10
automatic
manual
26
27
16
20
28
28
9
28
38
27
17
remove
rename
list
lock
watch
digital channel
subtitles
rename
reorder / rearrange
switch
21
28
23, 26
test reception
digital radio
digital services
CAM
test reception (digital channels)
troubleshooting
tune
33
16, 10, 15
23
teletext
update
disconnect USB
display
child lock
lock channels
lock connected devices
PIN code
ratings lock
clock
20
20
20
20
resolution
dispose
36
5
display
set
common interface
18
18
33
40 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
E
L
EasyLink
disable
enable
language
34
34
34
34
34
6
menu
26
21
38
subtitle
one-touch play
troubleshoot
list
favourites list
location
one-touch standby
system audio control
eco-green
16
end of life
5
country
26
24
energy efficiency
environmental care
e-sticker
6
5
24
home or shop
lock
Kensington lock
lock channels
lock connected devices
PIN code
ratings lock
35
20
20
20
20
F
factory settings
favourites list
add to list
25
17
16
16
27
create list
view list
M
menu
fine-tune channels
language
main menu
teletext
26
11
15
15
10
12
36
G
universal access
MHEG teletext
MPEG artifact reduction
multimedia
music
green
6
H
HDMI
39, 31, 29
digital radio
USB
23
23
23
34
hearing impaired
home mode
15
24
with slideshow
mute TV speakers
I
install channels
automatic
manual
O
26
27
OAD
24
19, 19
34
on timer
one-touch play
one-touch standby
K
34
Kensington lock
35
EN 41
Download from Www.Somanuals.com. All Manuals Search And Download.
smart sound
software
14
P
parental rating
PC
20
over the air download
update
24
24
24
14
36
9
connect
32, 39
36
version
resolution
sound settings
specifications
standby
picture format
change
troubleshooting
picture settings
PIN code
pixel plus link
power
power consumption
preferences
product specifications
13
38
subpages in teletext
subtitles
15
12
20
language
21
21
21
24
on analogue channel
on digital channel
switch
36
36, 6
24
channels
9
9
10
36
on and off
source
R
radio
23
T
rearrange channels
reception
recycle
register product
remote control
batteries
28
Table of Pages
technical specifications
teletext
16
36
28, 38
5
7
features
15
15
15
16
16
10
18
menu
subpages
Table of Pages
Teletext 2.5
use
36, 5
7
overview
technical specifications
rename channels
reorder channels
resolution
36
28
28
36
25
time zone
timer
restore default
on timer
19, 19
19
sleep timer
standby
19
S
transmission
transporting
troubleshooting
TV lock
36, 38
4
safety
4
5
screen care
settings
38
picture
sound
12
14, 12
12
lock channels
lock connected devices
PIN code
20
20
20
20
7
settings assistant
shop mode
side connectors
slideshow
view
with music
smart card
smart picture
smart settings
24
31
ratings lock
TV overview
22
23
33
12
12, 14
42 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
U
universal access menu
USB
15
disconnect USB
listen to music
update software
view photos
23
23
24
22
V
video format
technical specifications
volume
36
adjust
10
14
14
automatic levelling
delta
mute
10, 34
W
wall mount
4, 37
EN 43
Download from Www.Somanuals.com. All Manuals Search And Download.
44 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
EN 45
Download from Www.Somanuals.com. All Manuals Search And Download.
46 EN
Download from Www.Somanuals.com. All Manuals Search And Download.
© 2010 Koninklijke Philips Electronics N.V.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
|