®
CC4600 Series
1/3-inch Color Cameras
Installation/Operation Manual
C1902M (11/96)
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827
International Customers call (1-559) 292-1981 or FAX (1-559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
12. Power-Cord Protection - Power supply cords should be
routed so that they are not likely to be walked on or pinched
by items placed upon or against then, paying particular
attention to cords and plugs, convenience receptacles,
and the point where they exit from the appliance.
1.0 IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instruc-
tions should be read before the unit is operated.
2. Retain Instructions - The safety and operating instructions
should be retained for future reference.
13. Power Lines - An outdoor system should not be located
in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall into such power
lines or circuits. When installing an outdoor system, ex-
treme care should be taken to keep from touching such
power lines or circuits as contact with them might be fa-
tal. U.S.A. models only - refer to the National Electrical
Code Article 820 regarding installation of CATV systems.
3. Heed Warnings - All warnings on the unit and in the oper-
ating instructions should be adhered to.
4. Follow Instructions - All operating and use instructions
should be followed.
5. Cleaning - Unplug the unit from the outlet before clean-
ing. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
14. Overloading - Do not overload outlets and extension cords
as this can result in a risk of fire or electric shock.
6. Attachments - Do not use attachments not recommended
by the product manufacturer as they may cause hazards.
15. Object and Liquid Entry - Never push objects of any kind
into this unit through openings as they may touch dan-
gerous voltage points or short-out parts that could result
in a fire or electric shock. Never spill liquid of any kind on
the unit.
7. Water and Moisture - Do not use this unit near water - for
example, near a bath tub, wash bowl, kitchen sink, or
laundry tub, in a wet basement, near a swimming pool, in
an unprotected outdoor installation, or any area which is
classified as a wet location.
16. Servicing - Do not attempt to service this unit yourself as
opening or removing covers may expose you to danger-
ous voltage or other hazards. Refer all servicing to quali-
fied service personnel.
8. Accessories - Do not place this unit on an unstable stand,
tripod, bracket, or mount. The unit may fall, causing seri-
ous injury to a person and serious damage to the unit.
Use only with a stand, tripod, bracket, or mount recom-
mended by the manufacturer, or sold with the product.
Any mounting of the unit should follow the manufacturer’s
instructions, and should use a mounting accessory rec-
ommended by the manufacturer.
17. Damage Requiring Service - Unplug the unit from the out-
let and refer servicing to qualified service personnel un-
der the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into
the unit.
An appliance and cart combination should be
moved with care. Quick stops, excessive force,
and uneven surfaces may cause the appliance
and cart combination to overturn.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the
operating instructions.Adjust only those controls that
are covered by the operating instructions, as an im-
proper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the unit to its normal
operation.
9. Ventilation - Openings in the enclosure, if any, are pro-
vided for ventilation and to ensure reliable operation of
the unit and to protect it from overheating. These open-
ings must not be blocked or covered. This unit should not
be placed in a built-in installation unless proper ventila-
tion is provided or the manufacturer's instructions have
been adhered to.
e. If the unit has been dropped or the cabinet has been
damaged.
f.
When the unit exhibits a distinct change in perfor-
mance - this indicates a need for service.
10. Power Sources - This unit should be operated only from
the type of power source indicated on the marking label.
If you are not sure of the type of power supply you plan to
use, consult your appliance dealer or local power com-
pany. For units intended to operate from battery power,
or other sources, refer to the operating instructions.
18. Replacement Parts - When replacement parts are re-
quired, be sure the service technician has used replace-
ment parts specified by the manufacturer or have the same
characteristics as the original part. Unauthorized substi-
tutions may result in fire, electric shock or other hazards.
19. Safety Check - Upon completion of any service or repairs
to this unit, ask the service technician to perform safety
checks to determine that the unit is in proper operating
condition.
11. Grounding or Polarization - This unit may be equipped
with a polarized alternating-current line plug (a plug hav-
ing one blade wider than the other). This plug will fit into
the power outlet only one way. This is a safety feature. If
you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact
your electrician to replace your obsolete outlet. Do not
defeat the safety purpose of the polarized plug.
20. Coax Grounding - If an outside cable system is connected
to the unit, be sure the cable system is grounded. U.S.A.
models only-Section 810 of the National Electrical Code,
ANSI/NFPANo.70-1981, provides information with respect
to proper grounding of the mount and supporting struc-
ture, grounding of the coax to a discharge unit, size of
grounding conductors, location of discharge unit, connec-
tion to grounding electrodes, and requirements for the
grounding electrode.
Alternately, this unit may be equipped with a 3-wire
grounding-type plug, a plug having a third (grounding)
pin. This plug will only fit into a grounding-type power
outlet. This is a safety feature. If you are unable to insert
the plug into the outlet, contact your electrician to replace
your obsolete outlet. Do not defeat the safety purpose of
the grounding-type plug.
21. Lightning - For added protection of this unit during a light-
ning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and
disconnect the cable system. This will prevent damage to
the unit due to lightning and power-line surges.
Pelco Manual C1902M (11/96)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 FCC INFORMATION
1.2 SAFETY PRECAUTIONS
For USA customers
CAUTION
WARNING - This equipment has been tested and found to com-
ply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the
equipment is operated in a residential installation. This equip-
ment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harm-
ful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of
the following measures:
RISK OF ELECTRIC
SHOCK. DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRI-
CAL SHOCK DO NOT OPEN COVERS. NO USER
SERVICEABLE PARTS INSIDE. REFER SERVIC-
ING TO QUALIFIED SERVICE PERSONNEL.
This label may appear on the bottom of the unit due to space
limitations.
The lightning flash with an arrowhead symbol,
within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dan-
gerous voltage” within the product’s enclosure
that may be of sufficient magnitude to consti-
tute a risk of electric shock to persons.
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and re-
ceiver.
-
-
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced audio/TV techni-
cian for help.
The exclamation point within an equilateral tri-
angle is intended to alert the user to presence
of important operating and maintenance (ser-
vicing) instructions in the literature accompa-
nying the appliance.
Intentional or unintentional changes or modifications not ex-
pressly approved by the party responsible for compliance shall
not be made. Any such changes or modifications could void
the user’s authority to operate the equipment.
Warning
To prevent fire or shock hazard, do not expose units
not specifically designed for outdoor use to rain or
moisture.
The user may find the following booklet prepared by the Federal
Communications Commission helpful: “How to Identify and Re-
solve Radio-TV Interference Problems”. This booklet is avail-
able from the U.S. Government Printing Office, Washington, DC
20402, Stock No. 004-000-00345-4.
For United Kingdom customers
WARNING
THIS APPARATUS MUST BE EARTHED
IMPORTANT
The wires in the power supply lead are colored in accordance
with the following code:
WARNING: Electrostatic-sensitive device. Use proper
CMOS/MOSFET handling precautions to avoid electro-
static discharge.
Green-and-yellow:
Blue:
Brown:
Earth
Neutral
Live
NOTE: Grounded wrist straps must be worn and proper
ESD safety precautions observed when handling the
electrostatic-sensitive printed circuit boards.
As the colors of the wires in the power lead of this apparatus
may not correspond with the colored markings identifying the
terminals in your plug proceed as follows:
The wire which is colored green-and-yellow must be connected
to the terminal in the plug which is marked by the letter E or by
1.3 UNPACKING
the safety earth symbol
yellow.
or colored green or green-and-
The shipping carton is the safest container in which the unit
may be transported. Save it for possible future use.
The wire which is colored blue must be connected to the termi-
nal which is marked with the letter N or colored black.
The wire which is colored brown must be connected to the
Supplied
Accessories:
4-pin plug for auto iris lens (1); Operating
Instructions (1)
terminal which is marked with the letter L or colored red.
2
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 DESCRIPTION
The CC4600 series cameras are compact, rugged, full performance general purpose color CCD cameras. Contempo-
rary styling and concealed controls allow these cameras to blend naturally into the most modern installation sites.
These cameras are 1/3-inch image format and are available in the following models:
NOTE: The alphanumeric reference designations (of the form A ) used in this manual, are keyed to the
reference designations used in the instruction sheets shipped with the product received by the customer.
Model #
CC4600-2
CC4600-2X
CC4600-3
Voltage
24 VAC
24 VAC
230 VAC
Voltage Range
21 to 28
Nominal Power
4.5 W
Color
NTSC/EIA (60 Hz) 470TVL
PAL/CCIR (50 Hz) 470TVL
PAL/CCIR (50 Hz) 470TVL
21 to 28
4.5 W
198 to 264
5.5 W
These model cameras all have the following features in
common:
•
High sensitivity (minimum illumination: 1.9 lux,
F1.2)
•
•
CCD camera with electronic iris function
Automatic white balance tracking and adjustment
(normal/PRO)
•
•
Compatibility with DC controlled or video signal
controlled auto iris lenses
Automatic backlight compensation and automatic
flicker reduction (operates whenAGC switch is in
the “ON” position)
•
Line lock function for synchronizing through AC
power source
Figure 1. The CC4600 Series Camera
Pelco Manual C1902M (11/96)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
5
2.1 LOCATION AND FUNCTION OF
PARTS
Auto iris lens selection switch (DC/Video)
Switch for selecting the control signal for the auto
iris lens.
DC:
For auto iris lenses controlled by DC
signals
2.1.1 Top/Front/Side (Illustration A )
VIDEO: For auto iris lenses controlled by video
signals
1
Focal length adjustment ring and locking screw
Use this ring to adjust the focal length (the dis-
tance between the lens mounting plane and the
image plane). Use the locking screw to lock the
focal length.
NOTE: If you use the electronic iris function
in locations where the camera is exposed to fluo-
rescent light, a slow color change may occur.
2
Lens mount
Use to mount an appropriate C-mount or a CS-
mount lens. To attach a C-mount/CS-mount lens,
turn the focal length adjustment ring to the appro-
priate position. The factory setting is C mount.
NOTES: When the DC/VIDEO switch is set
to VIDEO, the backlight compensation func-
tion may not work properly.
When the DC/VIDEO switch is set to VIDEO,
“hunting” may occur. If this occurs, use the
LEVEL L/H adjustment screw on the lens to
change the incident light level. When adjusting
the incident light level, set theALC (Automatic
Light Control) adjustment screw to Av.
Lens connector (4 pin socket)
Supplies power and control signals to an auto iris
lens.
3
4
Camera mounting bracket
The mounting bracket can be attached to either the
top or bottom of the camera using the four attached
screws (1/4" UNC-20).
A
1
2
3
4
5
Top/Front/Side View of CC4600 Series Camera
4
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
2.1.2 Rear (Illustration B )
11
White balance mode switch
When set in the ATW (auto tracing white balance)
- PRO position, the camera automatically adjusts
white balance to suit the color temperature of vari-
ous lighting sources, including incandescent, fluo-
rescent and natural lighting.
SYNC switch
Use this switch to set the camera synchronization
mode—line lock (L.L) or internal (INT).
6
AGC (automatic gain control) ON/OFF switch
7
The automatic gain function automatically adjusts
picture gain in accordance with the brightness of
the subject.
When set to the ATW position, the camera auto-
matically adjusts white balance to suit special light-
ing sources such as sodium lamps.
Gain up switch
8
12 Aperture switch
Switching the Gain up switch to the TURBO mode
while the AGC switch is on increases gain by up
to 6dB over the NORM (normal) mode.
Set in the “SHARP” mode to sharpen the outline
and produce a clearer picture.
13
14
VIDEO OUT connector (BNC)
Ground terminal (screw type)
BLC (back lighting compensation) ON/OFF switch
9
When switched on, this function adjusts exposure
to compensate for situations where the subject is
lit from behind.
15 Power cable (model CC4600-3 only)
NOTE: When the BLC is in the “ON” posi-
tion, hunting may occur; that is, the image may
get darker and lighter as the camera “hunts”
for the best exposure level. If hunting occurs,
set the BLC switch to “OFF”.
16
24 VAC input terminals (models CC4600-2,
CC4600-2X)
17
Video level adjustment pot
Use to adjust the video level when using a DC servo
lens. If using a Video servo lens , turn the control
toward the H (high) side.
CCD-IRIS ON/OFF switch
10
When using a manual iris lens, the CCD-IRIS func-
tion automatically adjusts the shutter speed to main-
tain a suitable exposure level. Set switch to OFF if
using an auto-iris lens..
18
Vertical phase adjustment pot
Use to adjust the vertical phase of cameras syn-
chronized by line lock.
6
B
7
8
9
10
11
12
13
14
13
17
18
16
18
17
15
Rear View of CC4600 Series Cameras
Pelco Manual C1902M (11/96)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The power runs for user supplied wiring from a 24 VAC
supply to a CC3300-2 camera should be within the fol-
lowing limits:
3.0 POWER SUPPLY CONSIDERATIONS
Use only the recommended power supplies. Improper
substitutions may damage the camera or cause a shock
or fire hazard.
Up to 60 m (200 ft) — 1 mm2 (18 AWG) or larger.
Up to 100 m (325 ft) — 1.5 mm2 (16 AWG) or larger
CC4600-2/2X
Do not mistakenly attach the
GND terminal on 24 VAC
cameras to either of the power
terminal inputs. Be sure to use
the grounding lug or screw.
•
The CC3300-2 must always be operated with a 24
VAC, Class 2 (60 Hz) power supply (not supplied).
A wall transformer (as depicted in Figure 3) is an
example of a common power source.
•
In the USA, use a power supply which is UL Listed.
In Canada, use a power supply which is CSA Cer-
tified.
CC4600-3
•
The CC3300-3 must be always operated with a 220-
240 VAC, (50 Hz) power supply.
•
•
The CC4600-2X must always be operated with a
24 VAC (50 Hz) power supply.
NOTE: The CC4600-3 is supplied with an
attached main power cable cord. See Figure 2
legend for power connections.
When connecting to the transformer, be sure to
carefully connect each lead to the appropriate ter-
minal. Wrong connections may cause malfunction
and/or damage to video camera.
•
•
Ground the unit or an irregular voltage may be
generated in the AC power cord and may cause
malfunction or damage to the video camera.
24 VAC Cameras: do not exceed 24 VAC input.
Normal input voltage is 24 VAC
3
2
CC4600-2 & -2X
CC4600-3
4
GND
7
6
5
24VAC Input
POWER CONNECTIONS:
Brown Wire - Hot or Live wire
Blue Wire - Neutral wire
Green and Yellow wire - Earth Ground or GND
Figure 2. Rear Panels: CC4600-2/-2X and CC4600-3
6
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
•
120 VAC power source: The 24 VAC CC4600-2 camera must be wired to a 60 Hz source.
Typical Power Supply
To 24 VAC Terminals
Input
On Camera
120 VAC, 60 Hz
24 VAC Output
Figure 3. Typical 120 VAC to 24 VAC (60 Hz) Power Supply
•
230 VAC power source: The 24 VAC CC4600-2X and the 230 VAC CC4600-3 must be wired to a 50 Hz source.
Typical Power Supply
#2
To 24 VAC Terminals
#1
Input
On Camera
COM
220-240 VAC, 50 HZ
With 240 VAC Input: Use #1 and COM
With 220 VAC Input: Use #2 and COM
Figure 4. Typical 230 VAC to 24 VAC (50 Hz) Power Supply
NOTE: Cameras with 220-240 VAC power
cords are double insulated. Article 250-45 of
the National Electrical Code states that listed
products protected by a system of double insu-
lation shall not be required to be grounded.
Pelco Manual C1902M (11/96)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 LENSES
NOTE: Lenses that are suitable for a 1/3-inch
CCD should be used with this camera using C
or CS type lens mounts. Pelco 1/3" format
lenses are recommended for optimum perfor-
mance.The use of other lenses may impair cam-
era performance. When lenses for a 2/3-inch or
1/2-inch CCD are used, the viewing angle will
be slightly different.
4.1 LENS LIMITS
Lenses exceeding the dimensions shown in Figure 5
below cannot be used.
When the lens is not mounted on the camera head, be
sure to install the dust cap to protect the internal parts
from dust or damage.
4.2 LENS COMPATIBILITY
C
(Illustration C )
1
The lens must be either a C- or a CS-mount type weigh-
ing less than 1 kg (2.2 lbs). The protrusion behind the
mounting surface must be within the following limits:
2
1
2
3
4
C-mount lens
9 mm or less
CS-mount lens
4 mm or less
3
4
Compatible Lenses
4.0 mm Max Thread
(0.16" Max.)
For CS Lens
22.4 mm Max.
(0.88" Max.)
Lens
9.0 mm Max. Thread
(0.35" Max)
For C Lens
Figure 5. Standard Acceptable Lens Dimensions
8
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
4.3 LENS INSTALLATION
4.3.1 Auto Iris
D
2
3
1
Install an auto-iris lens as follows:
(Refer to Illustration E )
1. Unscrew lens mount cap.
8
7
2. Screw in the lens.
3. Check the plug wiring on the lens cable against
Illustration D and the pin-outs mentioned in the
Information Box below. If you need to replace the
existing plug on the lens cable, follow the instruc-
tions given.
6
4
5
Changing the Plug on an Auto Iris Lens Cable
4. As part of lens installation, you need to adjust
backfocusing. Follow the appropriate instructions
found in the Information Boxes on pages 11 and
12. Background “General Information”, if needed,
is provided on page 10.
4 2
Auto Iris Plug
Pin-out (Back of Plug)
3 1
5. Once adjusted, tighten the backfocus LOCK screw.
(The factory setting is C-mount.)
NOTE: When attaching a C-mount type lens,
be sure to turn the C/CS adjustment ring fully
in the “C” direction. When the C/CS adjust-
ment ring is set to “CS,” mounting any lens
with a mount projection of more than 4 mm
may damage the internal parts of the camera.
4.3.2 Manual Iris
Follow the instructions of the previous section but
ignore all instructions for changing the lens cable plug.
Plug Change on Auto Iris Lens Cable
2. Put the cover on the plug.
ILLUSTRATION D ELEMENTS
Information Box
Information Box
1. Remove the plug cover
and solder the lens
1
cable wires
to the pins
thru
on the
2
8
5
plug supplied. The pin assignments are as fol-
lows:
1
2
3
Cover
Pin #
DC-servo Lens
DRV+
VS-servo Lens
Video signal
Auto-iris cable
Pin 3:
8
7
6
Rib (If the cable is thick and the plug cover
does not seat properly, cut away this rib.)
Pin 1:
Pin 2:
CONT-
CONT+
DRV-
Power supply
Not Used
Ground
4
Lens plug
Pin 4: 5
Pelco Manual C1902M (11/96)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA/LENS GEOMETRY–GENERAL INFORMATION
LENS
(STYLIZED)
CAMERA
Incident Light
CCD Iris (Electronic Shutter) CCD out-
put voltage is electronically sampled and
used to adjust for small variations in light
levels. Normally used in indoor, fixed po-
sition applications where small variations
in light levels might be encountered. CCD
iris must be turned OFF when perform-
ing camera/lens adjustments.
CCD
IMAGER
C/CS Adjustment (all models) conditions camera mount
for lens type being used by changing physical distance
of imager face with respect to back of lens. Adjustment
screw or ring is initially positioned at the corresponding
C or CS position (corresponding to lens type) and not
some setting in between. Factory set at C position.
C
CS
IRIS
MANUAL
LENS
MOTORIZED
ZOOM LENS
The lens has
a focus ring
adjustment
on it.
Zoom lens which
can be remotely
controlled for zoom
and focus
Iris opening (sometimes referred to as aperture) is
defined by f/stop numbers. The higher the # the
more closed the iris is
Used when large
variations in lighting
are expected (usually
outside).There are two
types of auto-iris con-
trol
MOTORIZED IRIS
MANUAL IRIS
AUTO-IRIS
• Iris has motor on it which
is controlled remotely by
the operator
• Iris adjustment ring is
on the lens
• Fixed position applica-
tions
DC CONTROL
VIDEO CONTROL
• No automatic compen-
sation for light changes
• Iris operation con-
trolled by DC motor
voltages from the
camera
• Iris operation con-
trolled by video to
voltage motor con-
trol signals from the
camera
• Indoor use
• Minimal light variations
• Level control ON THE
• Level control ON
THE LENS
CAMERA
• Only choice available
if you wish to use the
auto-iris feature with
B/W cameras
10
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
Information Box
Information Box
Lens/Camera Setup and Backfocusing
The purpose of backfocusing is to make the adjustments necessary for the picture to remain in focus throughout the camera‘s zoom
range, which is the case for instance, in motorized zoom, auto iris configurations. Manual Iris lens/camera combinations also need to
be backfocused. Follow the general instructions listed below to adjust backfocus appropriate to your camera/lens combination
LENS TYPE
NOTE: We are essentially referencing indoor lighting condi-
tions in each of the cases below. If you have occasion to use
A
AUTO IRIS
B
fixed lenses in an outdoor setting, where lighting is much brighter
(not widely done with fixed lenses), you may need to filter the
light while performing these adjustments.
MANUAL IRIS
Generic Lens w/
Manual Iris &
Focus
STATIC LIGHT CONDITIONS
VARIABLE LIGHT CONDITIONS
• Adjust Backfocus the
same as was done for Vari-
able Light conditions ex-
cept CCD iris is left in the
OFF position; therefore
there is no need to adjust
the LVL control; follow all
other steps, however.
• Turn Manual Iris
ring so iris is fully
open and set the Fo-
cus ring for ∞ (or dis-
tant object).
Manual
Iris
Manual
Focus
• Set
all
other
CC3300 Series
CC4600 Series
switches on the
back of the Camera
to the left (deacti-
vated or OFF), in-
cluding the CCD
Iris switch.
Sync
AGC
Gain
BLC
CCD Iris** (OFF)
White
AGC
TURBO AGC
BLC
CCD IRIS**
Aperture
**With CCD Iris
OFF, the Video
Level control is
inactive
Generic example of best
setting for C mount lens.
• Adjust the C/CS
adjustment ring
for the best pic-
ture.
Best setting
Adjustment
Ring
Picture will be out
of focus on either
side of best setting
• Move CCD Iris switch
to the ON position.
AGC
TURBO AGC
BLC
Sync
AGC
Gain
BLC
CCD IRIS (ON)
CCD IRIS (ON)
White
Aperture
• Set the Iris/Video Level
control pot to the H posi-
tion.
IRIS LEVEL
VIDEO LEVEL
H
H
L
L
• Adjust or set other cam-
era switches as needed.
Pelco Manual C1902M (11/96)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Backfocusing
Information Box
Information Box
Lens/Camera Setup and Backfocusing
The purpose of backfocusing is to make the adjustments necessary for the picture to remain in focus throughout the camera‘s zoom
range, which is the case, for instance, in motorized zoom, auto iris configurations. Manual Iris lens/camera combinations also need to
be backfocused Follow the general instructions listed below to adjust backfocus appropriate to your camera/lens combination
LENS TYPE
NOTE: Most auto-iris configurations are associated with motorized zoom
lenses, so the instructions below are based on that assumption
B
MANUAL IRIS
A
AUTO IRIS
VIDEO SERVO
DC SERVO
CC3300 Series
CC4600 Series
• Make sure theAuto IrisVideo/
DC switch is in the DC posi-
tion. Use a neutral density
filter or some other physical
means to decrease the
amount of light entering the
camera lens so that the auto-
iris response is to open the iris
up as wide as possible.
• This step is the same as the
one for DC SERVO, excpt
that theAUTO IRIS VIDEO/
DC switch is set to VIDEO,
both models.
AUTO IRIS
VIDEO DC
AUTO IRIS
VIDEO DC
• Set all other switches on the
back of the Camera to the
left (deactivated or OFF), in-
cluding the CCD Iris
switch.
• This step, same as for DC
servo, both models.
Sync
AGC
Gain
BLC
CCD Iris** (OFF)
White
AGC
TURBO AGC
BLC
CCD IRIS**
Aperture
**With CCD Iris
OFF, the Video
Level control is
inactive
BACKFOCUS ADJUSTMENT
• Adjust focus to far, zoom to
wide angle.
Generic example of best
setting for C mount lens.
• This step, same as for DC
servo, both models.
Best setting
• Adjust C/CS adjustment
Ring on the camera for the
best picture.
Adjustment
Ring
• Zoom to a close object; ad-
just lens controller or focus
for best picture.
• Repeat above until lens re-
mains in focus throughout
the zoom range (far to near).
• Tighten the Lock Screw.
Picture will be out
of focus on either
side of best setting
The ability of a zoom lens to remain in focus throughout its zoom range is known as Tracking
IRIS LEVEL
• Finally, use the IRIS/VIDEO
LEVEL adjustment on the
REAR of the CAMERA to
adjust for best picture
• ForAUTO IRIS applications
using VIDEO servo, set the
IRIS/VIDEO LEVEL on the
rear of the respective units
to H.
VIDEO LEVEL
H
L
H
L
• Adjust other settings on cam-
era as needed.
12
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
E
1
4
3
5
2
Fitting the Lens
CAUTION: When mounting the lens, loosen
the securing nut on the side and
turn the focal length adjustment
to the C position. Mounting a C-
mount lens with the adjustment
ring in the CS position may dam-
age the optical filter.
Pelco Manual C1902M (11/96)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
To AC 24V terminals 1 and 2 (CC4600-2,
CC4600-2X)
5.0 CAMERA INSTALLATION
7
ATTENTION: Installation should be per-
formed by qualified service personnel only, in
accordance with the National Electrical Code
or equivalent/applicable local codes.
When using an external (L.L) synchronization signal,
set the L.L/INT switch (1) to L.L and make connec-
tions as above.
When attaching the camera to a ceiling bracket or tri-
pod, attach the supplied mounting bracket. The bracket
may be attached to either the top or bottom of the cam-
era. Use the supplied 1/4" UNC-20 screw to attach the
camera to the tripod or ceiling bracket.
CAUTION: Be sure cable wires
are routed so as to not pinch or rub
when connected to pan/tilt units.
Frayed, pinched or broken wires
can cause fire/shock hazards or
system failure.
5.1 Connections (Illustration F )
Using an internal synchronization signal.
5.2 Phase Adjustment (Illustration G )
1
Set the L.L/INT switch to “INT” (internal synchro-
nization).
When using more than one camera, connect to a cam-
era switcher and set the vertical phase range as follows:
2 Connect with VIDEO OUT connector.
3
4
1
2
Camera switcher
Monitor
Vertical phase
3
4
75-ohm coaxial cable
Adjustable range
Connect with VIDEO IN connector on a video
monitor, etc.
To power supply (CC4600-2, CC4600-2X); to a
wall outlet (CC4600-3)
5
6
Power cord
3
F
2
CC4600-2 & -2X
4
7
2
6
3
5
1
CC4600-3
4
6
5
Connecting the CC4600 Series Cameras
14
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
In such cases, camera switching may produce what ap-
pears to be a vertical roll on the monitor between the
two views. Turning the V Phase pot (while switching
rapidly as possible between the two camera views) will
adjust the relative phase angle between the two cam-
eras and the point at which one camera synchronizes to
the AC line with respect to the other. Adjust the pot
until the switching is clean and there is no vertical roll
or flip.
G
1
2
3
-90° 0° +90°
6.0 CCD CHARACTERISTICS
-90°
The following conditions which may be observed when
using a CCD camera are not due to any fault within the
camera.
0°
+90°
Vertical smear - This phenomenon occurs when view-
4
ing a very bright object.
Phase Adjustment
Patterned noise - This is a fixed pattern which may
appear over the entire monitor screen when the camera
is operated at a high temperature.
H
Jagged picture - When viewing stripes, straight lines,
or similar patterns, the image on the screen may appear
jagged.
7.0 HOUSEKEEPING
Be careful not to spill water or other liquids on the units,
or allow combustible or metallic objects to fall inside
the body. If used with foreign matter inside, the unit is
liable to fail, or be a cause of fire or a shock hazard.
Vertical Phase
7.1 OPERATION AND STORAGE
LOCATIONS
5.3 Vertical Phase (Illustration H )
Vertical phase adjustment is NOT vertical ROLL ad-
justment. Each camera is adjusted to theAC zero cross-
over point at the factory. Problems arise,however, (es-
pecially in larger systems) when:
Do not aim the camera at very bright objects such as
the sun or electric lights for an extended period. Avoid
operating or storing the unit in the following locations:
•
Extremely hot or cold places (operating tempera-
ture — 14° to 122° F [-10° to 50° C])
Damp or dusty places
Exposed to rain
Exposed to strong vibration
Close to generators of strong electromagnetic ra-
diation such as radio or TV transmitters
Exposed to fluorescent light reflections or unstable
(flickering) lighting conditions
1. Switching rapidly between widely separated cam-
eras with manual or sequential switchers.
•
•
•
•
2. Switching between cameras not operating off the
same phase of the AC line.
3. Both of the above. There are other causes too
(transformers wired backward, for instance) but
the basic symptoms described below require V-
phase adjustment.
•
Pelco Manual C1902M (11/96)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
7.2 CARE OF THE UNIT
•
•
Remove dust or dirt on the surface of the lens or
CCD with a blower.
Use a soft, dry cloth to clean the body. If it is very
dirty, use a cloth dampened with a small quantity
of a neutral detergent, then wipe dry.
•
Avoid using volatile solvents such as thinner, al-
cohol, benzene and insecticides. They may dam-
age the surface finish and/or otherwise impair the
operation of the camera.
CAUTION: The camera should
not be pointed at the sun, or used
for shooting very bright objects, as
the CCD imager may be perma-
nently damaged
8.0 MAINTENANCE
These color cameras, as shipped, are factory adjusted
and tested for optimum performance in most applica-
tions. No additional camera setup procedures should
normally be required. However, improved performance
may be obtained in some applications by field setup.
Setup should be limited to the procedures described
herein.
16
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating
Humidity:
9.0 SPECIFICATIONS
20 to 80%
Image Device: 1/3" interline transfer type CCD
Storage
Temperature:
-40° to 140° F (-40° to 60° C)
Effective Picture Elements:
CC4600-2:
CC4600-2X/
CC4600-3:
768 (horizontal) x 494 (vertical)
752 (horizontal) x 582 (vertical)
C-mount/CS-mount adjustable
Storage
Humidity:
20 to 80%
70 G
Shock
Resistance:
Lens Mount:
Signal System:
CC4600-2:
CC4600-2X/
CC4600-3:
Weight:
CC4600-2/
CC4600-2X: 550 g (1.20 lbs)
NTSC/EIA color system
PAL/CCIR color system
CC4600-3:
Construction:
Finish:
770 g (1.68 lbs)
Synchronization
System:
Steel case
Internal/line lock
470 lines
Neutral Gray
See Figure 6
Horizontal
Resolution:
Dimensions:
Minimum
Design and specifications are subject to change with-
out notice.
Illumination:
1.9 lux, F1 .2 (with AGC set to ON in
TURBO mode)
Video Output: 1 Vp-p, 75 ohm, negative sync
Video S/N: 50 dB (with AGC set to OFF)
White Balance: ATW/ATW PRO (switchable)
Automatic Gain
Control (AGC): Switchable: ON/OFF with Gain up
(TURBO/NORM)switchinTURBO
position and AGC ON, a 6 dB gain
increase over NORM mode results.
5.50 (139.70)
1/4-20 MOUNT NUT
(TOP AND BOTTOM)
5.06
(128.52)
C
CS
1.09
(27.69)
CS
C
2.13 (53.97)
Power Requirements:
2.75
(69.85)
CC4600-2:
CC4600-2X: 24 VAC (50 Hz)
24 VAC (60 Hz)
1.38
(34.93)
CC4600-3:
220-240 VAC (50 Hz)
5.50 (139.70)
Power Consumption:
CC4600-2/
CC4600-2X: Less than 4.5 W
2.56
(65.09)
2.19
(55.56)
CC4600-3:
5.5 W
Operating
Temperature:
14° to 122° F (-10° to 50° C)
NOTE: VALUES IN PARENTHESES ARE MILLIMETERS;
ALL OTHERS ARE INCHES
Figure 6. CC4600 Series Dimension Drawing
Pelco Manual C1902M (11/96)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
10.0 WARRANTY AND RETURN INFORMATION
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
18
Pelco Manual C1902M (11/96)
Download from Www.Somanuals.com. All Manuals Search And Download.
|