I N S T A L L A T I O N
IS150 Series
Camclosure®
Integrated Camera System
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Regulatory Notices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Cover and Back Box Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Unshielded Twisted Pair (UTP) Video. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Fixed Ceiling/Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Suspended Ceiling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4S Deep Electrical Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Camera Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Module Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Camera Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Module Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Camera Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Varifocal Lens Zoom and Focus Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
DN/CH Series Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Auto Iris Level Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Vertical Phase Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Blemish Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Day/Night Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DW/CW Series (Wide Dynamic Range) Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Switch Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Auto Iris Level Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Vertical Phase Adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Blemish Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Camera Positioning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Install Liner and Trim Ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Service Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
3
List of Illustrations
Package Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Ceiling/Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ceiling Tile Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4S Deep Electrical Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Camera Module Bracket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Back Box Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Camera Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Location of Zoom and Focus Locking Screws . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Adjusting the Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Adjusting the IS150-DN/CH Series Camclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
DN Models Threshold Switching Levels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adjusting the IS150-DW/CW Series Camclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
DW Models Threshold Switching Levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Positioning the Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Adjusting the Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Service Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Attaching the 2.5 mm Monaural Headphone Plug. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
List of Tables
IS150, Smoked Bubble Without Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
IS151, Clear Bubble with Liner. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power Input: Fixed Ceiling/Wall Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Power Input: Suspended Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power Input: 4S Deep Electrical Box Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
DN Models Switching Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
DW Models Switching Thresholds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio/TV technician for help.
You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve
Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment
can void your authority to operate this equipment under Federal Communications Commission’s rules.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
WARNING: This product is sensitive to Electrostatic Discharge (ESD). To avoid ESD damage to
this product, use ESD safe practices during installation. Before touching, adjusting or handling this
product, correctly attach an ESD wrist strap to your wrist and appropriately discharge your body
and tools. For more information about ESD control and safe handling practices of electronics,
please refer to ANSI/ESD S20.20-1999 or contact the Electrostatic Discharge Association
(www.esda.org).
The materials used in the manufacture of this document and its components are compliant to the
requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to
comply with Directive 2002/96/EC of the European Union regarding the disposal of waste electrical
and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this
equipment.
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Description
The IS150 Series Camclosure® integrated camera system combines an environmental cover, back box,
camera, lens, and lower dome into a small, high-security system that is quick and easy to install. The
system is perfect for a variety of indoor and outdoor applications and its versatile design allows for
multiple mounting options. The unit supports both BNC and unshielded twisted pair (UTP) video wiring.
The IS150 Series Camclosure integrated camera system can be installed directly into a ceiling, wall, or
4S deep electrical box.
Before installing your new system, thoroughly familiarize yourself with the information in this manual.
MODELS
The IS150 models include the following specifications: Indoor/outdoor dome, vandal resistant, in-ceiling
mount, smoked bubble, gray finish.
Table A. IS150, Smoked Bubble Without Liner
Camera Type
Lens/Iris
NTSC
PAL
Color, Wide Dynamic
Range, Day/Night
3.0 to 9.5 mm, Day/Night Varifocal,
Auto Iris
IS150-DWV9
—
—
9.0 to 22.0 mm, Day/Night Varifocal,
Auto Iris
IS150-DWV22
IS150-DNV9
IS150-DNV22
Color, High Resolution, 3.0 to 9.5 mm, Day/Night Varifocal,
Day/Night
IS150-DNV9X
IS150-DNV22X
Auto Iris
9.0 to 22.0 mm, Day/Night Varifocal,
Auto Iris
Color, Wide Dynamic
Range
3.0 to 9.5 mm, Varifocal, Auto Iris
IS150-CWV9
IS150-CWV22
—
—
9.0 to 22.0 mm, Day/Night Varifocal,
Auto Iris
Color, High Resolution
3.0 to 9.5 mm, Varifocal, Auto Iris
9.0 to 22.0 mm, Varifocal, Auto Iris
3.0 mm, Fixed, Manual Iris
3.6 mm, Fixed, Manual Iris
6.0 mm, Fixed, Manual Iris
8.0 mm, Fixed, Manual Iris
12.0 mm, Fixed, Manual Iris
IS150-CHV9
IS150-CHV22
IS150-CH3
IS150-CH3.6
IS150-CH6
IS150-CH8
IS150-CH12
IS150-CHV9X
IS150-CHV22X
IS150-CH3X
IS150-CH3.6X
IS150-CH6X
IS150-CH8X
IS150-CH12X
6
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Indoor/outdoor dome, vandal resistant, in-ceiling mount, clear bubble, liner, gray finish
Table B. IS151, Clear Bubble with Liner
Camera Type
Lens/Iris
NTSC
PAL
Color, Wide Dynamic
Range, Day/Night
3.0 to 9.5 mm, Day/Night Varifocal,
Auto Iris
9.0 to 22 mm, Day/Night Varifocal,
Auto Iris
IS151-DWV9
—
—
IS151-DWV22
IS151-DNV9
IS151-DNV22
Color, High Resolution, 3.0 to 9.5 mm, Day/Night Varifocal,
Day/Night
IS151-DNV9X
IS151-DNV22X
Auto Iris
9.0 to 22.0 mm, Day/Night Varifocal,
Auto Iris
Color, Wide Dynamic
Range
3.0 to 9.5 mm, Varifocal, Auto Iris
IS151-CWV9
IS151-CWV22
—
—
9.0 to 22.0 mm, Day/Night Varifocal,
Auto Iris
Color, High Resolution
3.0 to 9.5 mm, Varifocal, Auto Iris
9.0 to 22.0 mm, Varifocal, Auto Iris
3.0 mm, Fixed, Manual Iris
3.6 mm, Fixed, Manual Iris
6.0 mm, Fixed, Manual Iris
8.0 mm, Fixed, Manual Iris
12.0 mm, Fixed, Manual Iris
IS151-CHV9
IS151-CHV22
IS151-CH3
IS151-CH3.6
IS151-CH6
IS151-CH8
IS151-CH12
IS151-CHV9X
IS151-CHV22X
IS151-CH3X
IS151-CH3.6X
IS151-CH6X
IS151-CH8X
IS151-CH12X
PARTS LIST
Qty Description
1
IS150 Series Camclosure integrated camera system
• Back box
• Trim ring with bubble; clear bubble models include a liner
• Camera module
1
1
4
2
4
Adapter plate
1/8-inch hollow screwdriver bit
Screws, 8-32 x 0.375-inch, Phillips flat head
Screws, 8-32 x 0.75-inch, Phillips flat head
Screws, 8-32 x 1.25-inch, Phillips flat head
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
7
SHIPPING BOX
CAMERA MODULE
BACK BOX
1 EA.
1 EA.
TRIM RING, LINER,
AND CLEAR BUBBLE
1 EA.
TRIM RING AND
SMOKED BUBBLE
1 EA.
< OR >
ADAPTER PLATE
1 EA.
1/8-INCH HOLLOW
SCREWDRIVER BIT
1 EA.
SHOWN ACTUAL SIZE
8-32 X 0.375-INCH
PHILLIPS FLAT HEAD
SCREWS
8-32 X 0.75-INCH
PHILLIPS FLAT HEAD
SCREWS
8-32 X 1.25-INCH
PHILLIPS FLAT HEAD
SCREWS
4 EA.
2 EA.
4 EA.
Figure 1. Package Components
8
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Cover and Back Box Installation
The IS150 Series Camclosure integrated camera system mounts only into a wall or ceiling.
UNSHIELDED TWISTED PAIR (UTP) VIDEO
The IS150 Series offers support for unshielded twisted pair (UTP). The UTP video output signal is 1 Vp-p
differential into a 100-ohm load. At a minimum, UTP requires Cat5, 100-ohm twisted pair cable.
FIXED CEILING/WALL
NOTE: You should install the camera module into the back box before installing the back box into the
surface. When installing the back box into the surface, rotate the camera module to access the mounting
1. Cut a hole 3.5 inches (9 cm) in diameter in the ceiling or wall. Use the adapter plate (supplied) as
a template.
2. Pull the video and power wires through the ceiling or wall.
3. Connect the video cable and wires:
•
•
BNC: Connect the BNC connector from the unit to a mating BNC connector.
UTP: Connect the blue wire to Video +; connect the gray wire to Video -.
Table C. Power Input: Fixed Ceiling/Wall Installation
Voltage Red Wire Black Wire
12 VDC
24 VAC
+
~
Ground
~
AC operation only: If you are wiring more than one Camclosure to the same transformer, connect one
side of the transformer to the red wire on all units; connect the other side of the transformer to the
black wire on all units.
NOTE: Failure to connect all AC powered units the same way will cause the cameras to be out of
phase with each other, which may produce a vertical roll when switching between cameras.
5. For a nonconcrete ceiling/wall, use 6-32 toggle bolts to attach the surface mount ring and back box
to the mounting surface. For a concrete ceiling/wall, use 8-32 mounting hardware. Mounting
hardware is not supplied.
WALL OR
CEILING
MOUNTING
HARDWARE
(NOT SUPPLIED)
BACK BOX
Figure 2. Ceiling/Wall Installation
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
9
SUSPENDED CEILING
NOTE: You should install the camera module into the back box before installing the back box into the
surface. When installing the back box into the surface, rotate the camera module to access the mounting
1. Pull the video and power wires to the ceiling tile.
a.
b.
Remove the ceiling tile from the ceiling.
Cut a hole 3.5 inches (9 cm) in diameter in the ceiling tile. Use the adapter plate (supplied) as
a template. Punch four screw holes in the ceiling tile.
c.
d.
Attach the back box to the ceiling tile and adapter plate with four 8-32 x 1.25-inch Phillips flat
head screws (supplied).
Reinstall the ceiling tile with the unit.
ADAPTER PLATE
CEILING TILE
8-32 X 1.25-INCH
PHILLIPS FLAT
BACK BOX
HEAD SCREWS
(SUPPLIED)
Figure 3. Ceiling Tile Installation
3. Remove an adjacent ceiling tile.
4. Connect the video cable and wires:
•
•
BNC: Connect the BNC connector from the unit to a mating BNC connector.
UTP: Connect the blue wire to Video +; connect the gray wire to Video -.
Table D. Power Input: Suspended Installation
Voltage Red Wire Black Wire
12 VDC
24 VAC
+
~
Ground
~
AC operation only: If you are wiring more than one Camclosure to the same transformer, connect one
side of the transformer to the red wire on all units; connect the other side of the transformer to the
black wire on all units.
NOTE: Failure to connect all AC powered units the same way will cause the cameras to be out of
phase with each other, which may produce a vertical roll when switching between cameras.
10
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
4S DEEP ELECTRICAL BOX
NOTE: You should install the camera module into the back box before installing the back box into the
surface. When installing the back box into the surface, rotate the camera module to access the mounting
1. Attach the supplied adapter plate to the 4S box with two 8-32 x 0.75-inch Phillips flat head screws
(supplied).
2. Pull the video and power wires to the ceiling tile.
3. Connect the video cable and wires:
•
•
BNC: Connect the BNC connector from the unit to a mating BNC connector.
UTP: Connect the blue wire to Video +; connect the gray wire to Video -.
Table E. Power Input: 4S Deep Electrical Box Installation
Voltage Red Wire Black Wire
12 VDC
24 VAC
+
~
Ground
~
AC operation only: If you are wiring more than one Camclosure to the same transformer, connect one
side of the transformer to the red wire on all units; connect the other side of the transformer to the
black wire on all units.
NOTE: Failure to connect all AC powered units the same way will cause the cameras to be out of
phase with each other, which may produce a vertical roll when switching between cameras.
5. Attach the back box to the adapter plate with four 8-32 x 0.375-inch Phillips flat head screws
(supplied).
4S DEEP
ELECTRICAL
BOX
WALL OR
8-32 X 0.75-INCH
CEILING
PHILLIPS FLAT
HEAD SCREW
(SUPPLIED)
ADAPTER PLATE
BACK BOX
8-32 X 0.375-INCH
PHILLIPS FLAT
HEAD SCREW
(SUPPLIED)
Figure 4. 4S Deep Electrical Box Installation
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Camera Module
The IS150 Series Camclosure camera module includes the camera, camera bracket, and heater board. To
perform most camera adjustments, you must remove the module from the back box.
Use the following instructions to remove and reinstall the camera module.
WARNING: Heater elements could be hot! When camera power is on, use caution when adjusting
the camera. This applies to all models.
MODULE REMOVAL
To remove the camera module from the back box:
BRACKET
Figure 5. Camera Module Bracket
12
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
CAMERA ORIENTATION
At the factory, the camera module is configured for ceiling mounting. For wall mounting, you must change
the camera orientation or the video image could be upside down or sideways.
1. Remove the camera module from the back box, if necessary.
2. Remove the tilt adjustment screw and lock washer from each side of the camera.
3. Carefully rotate the camera one quarter or one half turn, depending on the desired camera angle.
NOTES:
•
•
•
Make sure to orient the top of the camera to the top of the field of view.
Make sure the wiring harness does not bind.
Make sure to orient the service connector away from the back box.
4. Reinstall the tilt adjustment screw and lock washer on each side of the camera.
5. Verify the camera orientation.
CEILING MOUNT (DEFAULT)
WALL MOUNT
TOP
OF CAMERA
BOTTOM
OF CAMERA
TILT ADJUSTMENT
SCREW AND
TILT ADJUSTMENT
SCREW AND
LOCK WASHER
LOCK WASHER
HEATER BOARD
HEATER BOARD
Figure 7. Camera Orientation
MODULE INSTALLATION
To install the camera module into the back box:
a.
b.
c.
Service (3-pin) connector
Camera (10-pin) connector
Heater board (4-pin) connector
2. Make sure the tabs on the camera bracket and the service connector are pointing out of the
enclosure, away from the ceiling or wall.
3. Gently squeeze the bracket, place it against the groove inside the back box, and gently release (refer
14
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Adjustments
To perform the following camera adjustments, make sure to connect the camera and service connectors.
You may have to remove the camera module from the back box.
Connect a monitor. Then turn on power to the camera and monitor. To use the service connector, refer to
To set the DIP switches, or to adjust the auto iris level (DN or CH) or the vertical phase (DW or CW), you
will need a miniature trimpot adjustment tool with a 0.05-inch (1.27 mm) blade. Suggested tools include a
miniature flat-tip screwdriver, a Philmore trimpot tool (#63-8608), and the Philmore 10-piece tool set
(#63-910). To adjust the lens, you may also need a miniature Phillips screwdriver.
After you have adjusted the unit, reinstall the camera module into the back box, and then install the trim
ring, bubble, and liner (if necessary).
VARIFOCAL LENS ZOOM AND FOCUS ADJUSTMENTS
NOTE: You will need a miniature Phillips or flat-tip screwdriver to loosen and tighten the locking screws.
To adjust the field of view:
2. Turn the zoom adjustment ring clockwise or counterclockwise to select the field of view.
3. Tighten the zoom locking screw.
FOCUS
ZOOM
Figure 8. Location of Zoom and Focus Locking Screws
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
15
To adjust the focus:
1. Loosen the focus locking screw.
2. Position the inverted dome approximately 0.125 inch (3.175 mm) from the front of the lens.
3. Turn the focus locking screw clockwise or counterclockwise to adjust the focus.
4. When the optimal focus is reached, tighten the focus locking screw
ZOOM
FOCUS
0.125 INCH (3.175 mm)
CENTER BUBBLE
WITH LENS
Figure 9. Adjusting the Focus
16
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
DN/CH SERIES ADJUSTMENTS
Figure 10. Adjusting the IS150-DN/CH Series Camclosure
SWITCH SETTINGS
Locate the DIP switch. Then set the switches for your installation.
SW4-1: Auto Gain Control
The automatic gain control (AGC) adjusts the image automatically to compensate for changes in light
levels.
Set SW4-1 to ON to enable AGC. Set it to OFF to disable AGC. The default setting is ON.
SW4-2: Backlight Compensation
The backlight compensation (BLC) feature compensates for backlit scenes by enhancing objects in the
center of the scene.
Set SW4-2 to ON to enable BLC. Use this setting if a bright backlight is present and the subject in the
center of the picture appears dark or as a silhouette.
Set it to OFF to disable backlight compensation. This is the default setting.
SW4-3: Line Sync
When multiple cameras are connected to the same switching device, vertical roll may occur on the
monitor. AC line lock eliminates vertical roll by locking the frame rate to the power supply frequency. Each
page 19 for more information).
Internal line sync disables line lock and synchronizes cameras internally.
Set SW4-3 to OFF to use AC line lock.
Set it to ON to use internal line sync. The default setting is OFF.
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
17
SW4-4: Flickerless
In certain lighting conditions, a flicker in the light source may affect camera operation. Flickering can be
caused by a number of conditions, including the quality of the source power and the age and type of
fluorescent bulbs and ballasts.
Set SW4-4 to ON to enable flickerless operation. The camera will remove the effects of flickering when
present. The shutter speed will be set to 1/120 (NTSC) or 1/100 (PAL).
Set it to OFF to disable flickerless operation. This is the default setting.
NOTE: If you enable flickerless operation, you should use AC line lock for best results.
SW4-5: Auto White Balance/Manual White Balance
Auto white balance (AWB) is enabled by default (OFF).
To manually set and lock the white balance:
1. Set SW4-5 to OFF.
2. Hold a white background in front of the lens until the video shows all white.
3. While holding the background in place, set SW4-5 to ON. A blue blinking block appears on the video
image for a few seconds. When the block changes to solid green, the manual white balance (MWB)
process is complete.
SW4-6: Reserved
Do not change SW4-6 from its factory setting. SW4-6 must be set to OFF for Varifocal models; it must be
set to ON for fixed-iris lenses.
AUTO IRIS LEVEL ADJUSTMENT
To adjust the auto iris DC-drive level (refer to Figure 10 on page 17):
1. Tilt or rotate the camera module until you can access the auto iris level control (R19).
2. Turn the screw clockwise to increase the brightness level or counterclockwise to decrease the
brightness level.
18
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
VERTICAL PHASE ADJUSTMENT
Use this procedure for 24 VAC operation only.
When using more than one camera power supply, a brief vertical roll may occur on the monitor when
switching from one camera to another.
To eliminate vertical roll, reverse the 24 VAC connections on one camera. If both cameras are connected to
the same transformer, this should solve the problem. If the problem persists, adjust the phase control by
synchronizing, or line-locking, the cameras to one another.
NOTE: When adjusting vertical phase, line sync (SW4-3) must be set to OFF for AC line lock.
Adjusting Vertical Phase
You may need two people when synchronizing the cameras: one at the camera, the other at the monitor to
observe the vertical roll and the effect of any camera adjustments.
To synchronize the cameras:
1. Choose a reference camera to which all other cameras will be phased.
2. Select the camera to synchronize. Use buttons SW1 and SW2 to synchronize the camera to the
vertical phase.
3. Each time an adjustment is made, switch back and forth between the camera you are adjusting and
the reference camera. Repeat this process as many times as necessary until the roll between the
cameras is no longer noticeable.
4. Adjust the phase of all other cameras by repeating steps 2 through 3. Always adjust to the reference
camera selected in step 1.
NOTE: The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the
vertical sync pulses of the reference camera to the selected camera(s).
BLEMISH DETECTION
If small white or color spots appear in the video image, one or more pixels on the camera imager may be
defective. (This condition is common for both CCD and CMOS imagers.)
DN and CH Series cameras with auto iris lenses automatically detect and correct defective pixels during
startup. Video turns on, then off, and then on again. If white or color spots still appear, you can correct the
defective pixels manually.
CH Series cameras with fixed iris lenses do not automatically detect and correct defective pixels. You can
correct the defective pixels manually.
1. Cover the lens completely. Make sure no light can enter the lens.
NOTE: The mechanical iris lens aperture does not completely block the light.
2. Press and hold button SW3 for one second. The camera will find and correct defective pixels;
however, any defective pixels that cannot be completely corrected may still appear.
3. Release button SW3.
4. Uncover the lens for normal camera operation.
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
19
DAY/NIGHT OPERATION
NOTE: This section only applies to DN model cameras.
DN model cameras regularly check the brightness level of the field of view to determine when to switch
between day (color) and night (black-white) operation.
Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view, lens, and
type of lighting. The switching process lasts from seven to 10 seconds.
3.0 lux
1.5 lux
Figure 11. DN Models Threshold Switching Levels
Table F. DN Models Switching Thresholds
Color to B-W 1.5 lux 1.0 lux
B-W to Color 3.0 lux 1.0 lux
installing the unit.
20
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
DW/CW SERIES (WIDE DYNAMIC RANGE) ADJUSTMENTS
SW1
DEFAULT SWITCH POSITION
R7
Figure 12. Adjusting the IS150-DW/CW Series Camclosure
SWITCH SETTINGS
Locate the DIP switch. Then set the switches for your installation.
SW1-1: Video Format
Set SW1-1 to ON for NTSC. Set it to OFF for PAL. The default setting is ON.
SW1-2: Line Sync
When multiple cameras are connected to the same switching device, vertical roll may occur on the
monitor. AC line lock eliminates vertical roll by locking the frame rate to the power supply frequency. Each
page 24 for more information).
Internal line sync disables line lock and synchronizes cameras internally.
Set SW1-2 to ON to use AC line lock. Set it to OFF for internal line sync. The default setting is ON.
SW1-3: Interlaced Scanning/Progressive Scanning
Interlaced scanning is the standard for analog recording installations. Each frame contains one odd and
one even field, each processed separately.
Progressive scanning is better for digital recording installations. Each frame is processed as a whole,
which results in less blurring and cleaner digital conversion. It also saves storage space on digital video
recorders.
Set SW1-3 to ON to select interlaced scanning. Set it to OFF to select progressive scanning. The default
setting is ON.
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
21
SW1-4: Auto White Balance/Manual White Balance
Auto white balance (AWB) is enabled by default (ON).
To manually set and lock the white balance:
1. Set SW1-4 to ON.
2. Hold a white background in front of the lens until the video shows all white.
3. While holding the background in place, set SW1-4 to OFF. A green block and a white block alternate
briefly on the video image until the manual white balance (MWB) process is complete.
SW1-5: Fluorescent/General
Enable this option to adjust the camera for best operation under fluorescent lighting.
Set SW1-5 to OFF for fluorescent lighting. Set it to ON for general lighting. The default setting is ON.
NOTE: If you use fluorescent operation, you should use AC line lock for best results.
SW1-6: General/Maximum Wide Dynamic Range
Maximum wide dynamic range (WDR) supports about 36 dB of additional dynamic range over a standard
camera. Use it for installations that require the maximum WDR.
General WDR supports about 20 dB of additional dynamic range over a standard camera. Use it for
installations that do not require the maximum WDR.
Set SW1-6 to ON to select maximum WDR. Set it to OFF to select general WDR. The default setting is ON.
SW1-7: DSS (Digital Slow Shutter)
The default shutter speed for NTSC is 30 frames per second (fps). It is 25 fps for PAL. This is also known as
SENS 2X.
You can decrease the shutter speed to 7.5 fps (NTSC) or 6.25 fps (PAL). This is known as SENS 8X, which
improves low light sensitivity.
Set SW1-7 to ON to select SENS 2X. Set it to OFF to select SENS 8X. The default setting is ON.
22
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
SW1-8: Day/Night Operation (DW models only)
NOTE: On CW models, SW1-8 is unused and does not affect camera operation.
DW model cameras regularly check the brightness level of the field of view to determine when to switch
between day (color) and night (black-white) operation. Use SW1-8 to set the general light levels at which
the camera will automatically switch.
Set SW1-8 to ON (dark) to use standard thresholds to switch between color and black-white operation.
This is the default.
Set it to OFF (dusk) to use higher light thresholds to switch between color and black-white operation.
Actual brightness threshold levels are affected by camera angle, amount of zoom, field of view, lens, and
type of lighting. The switching process lasts from seven to 10 seconds.
NOTE: If the camera switches between day/night mode at least three consecutive times within a short
time period, the camera will remain in the last mode for 10 minutes. To override this 10-minute pause,
cycle the power or expose the camera to an extreme light level change (for example, from very dim light to
very bright light).
setting.
7.0 lux
4.0 lux
3.0 lux
1.0 lux
DARK
Figure 13. DW Models Threshold Switching Levels
Table G. DW Models Switching Thresholds
DUSK
Dark (ON)
1.0 lux
Dusk (OFF)
4.0 lux
Color to B-W
B-W to Color
3.0 lux
7.0 lux
NOTE: These switching thresholds are approximate and were measured using a 3.0 to 9.5 mm lens at
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
23
AUTO IRIS LEVEL ADJUSTMENT
The electronics of the IS150-DW and IS150-CW Series Camclosures automatically adjust the camera to
the auto iris. Auto iris level adjustments are not necessary.
VERTICAL PHASE ADJUSTMENT
Use this procedure for 24 VAC operation only.
When using more than one camera power supply, a brief vertical roll may occur on the monitor when
switching from one camera to another.
To eliminate vertical roll, reverse the 24 VAC connections on one camera. If both cameras are connected to
the same transformer, this should solve the problem. If the problem persists, adjust the phase control by
synchronizing, or line-locking, the cameras to one another.
NOTE: When adjusting vertical phase, line sync (SW1-2) must be set to ON for AC line lock.
Adjusting Vertical Phase
You may need two people when synchronizing the cameras: one at the camera, the other at the monitor to
observe the vertical roll and the effect of any camera adjustments.
To synchronize the cameras:
1. Choose a reference camera to which all other cameras will be phased.
2. Select the camera to synchronize. Use the phase adjustment control (R7) to synchronize the camera
phase; turn R7 counterclockwise to decrease vertical phase.
3. Each time an adjustment is made, switch back and forth between the camera you are adjusting and
the reference camera. Repeat this process as many times as necessary until the roll between the
cameras is no longer noticeable.
4. Adjust the phase of all other cameras by repeating steps 2 through 3. Always adjust to the reference
camera selected in step 1.
NOTE: The preferred method for camera phase adjustment is to use a dual trace oscilloscope to align the
vertical sync pulses of the reference camera to the selected camera(s).
BLEMISH DETECTION
If small white or color spots appear in the video image, one or more pixels on the camera imager may be
defective. (This condition is common for both CCD and CMOS imagers.)
DW and CW Series cameras have auto iris lenses and automatically detect and correct defective pixels
during startup. Manual pixel correction is not available.
24
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Camera Positioning
Rotate and tilt the camera module to position the camera. Then tighten the tilt screws (axis ì in
NOTE: Do not over-rotate the module. Excessively turning the module in one direction could result in
damage to the wiring.
ᕣ
ᕡ
ᕢ
ì Tilt 80° (20° to 100°)
î Pan 360°
ï Rotation 360°
Figure 14. Positioning the Camera
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Install Liner and Trim Ring
a.
Align the screw holes in the trim ring with those in the back box to identify the proper liner
position.
b.
c.
Loosen the three Phillips screws located in the trim ring.
Insert the blade of a standard screwdriver in one of the adjustment grooves. Rotate the liner
to position the viewing window over the camera lens.
d.
Tighten the three Phillips screws to lock the liner in place.
ADJUSTMENT
GROOVE
LINER
LOOSEN SCREWS
Figure 15. Adjusting the Liner
2. Place the trim ring onto the back box.
3. Tighten the tamper-resistant screws through the trim ring into the back box. Use the 1/8-inch hollow
screwdriver bit (supplied).
NOTE: The screws are installed at an angle.
26
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Service Connector
The IS150 Series Camclosure integrated camera system includes a service connector that outputs camera
video. Use it at the installation site to set up the field of view and to focus the camera.
SERVICE
CONNECTOR
Figure 16. Service Connector
Pelco offers two optional items that plug directly into the service connector. Before using either option,
you must loosen the tamper-resistant screws to remove the trim ring from the back box. Use the 1/8-inch
hollow screwdriver bit (supplied).
The optional CST150 has a 3-foot (0.9 m) cable and microdisplay for viewing camera video. Plug it into the
service connector and view the video.
NOTE: The three buttons on the CST150 are not used with the IS150 Series Camclosure.
The optional IS-SC is a 4-foot (1.2 m) cable with a service connector and a BNC connector. Plug the service
connector into the unit. Then connect the other end to any standard BNC (VIDEO IN) connector on a
monitor.
To assemble a longer service cable for the Camclosure integrated camera system, purchase the following
items from a local electronics supply store:
Qty Description
1
1
1
2.5 mm monaural headphone plug
CPM 88 miniature coaxial connector
RG174/U coaxial cable
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
27
To assemble the cable:
1. Attach the CPM 88 miniature coaxial connector to one end of the cable. Follow the directions
supplied with the miniature coaxial connector.
a.
b.
c.
d.
e.
f.
Remove the support sleeve from the plug.
Slip the support sleeve over the end of the cable.
Prepare the cable.
Solder the center connector of the cable to the center pin of the plug.
Thread the braid of the cable through the hole in the crimp pin.
Solder the braid to the top of the crimp pin.
Crimp the end of the crimp pin around the cable.
Reassemble the support sleeve and the plug.
g.
h.
CENTER CONDUCTOR
COAXIAL
CABLE
2.5 MM MONAURAL
HEADPHONE PLUG
BRAID (SHIELD)
Figure 17. Attaching the 2.5 mm Monaural Headphone Plug
28
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
GENERAL
Pan/Tilt Adjustment
Manual
Pan
360°
Tilt
Rotation
80° (20° to 100° range)
360°
Construction
Finish
Aluminum with steel camera mounting bracket and polycarbonate dome
White polyester powder coat trim ring with gray polyester powder coat
back box
Light Attenuation
Smoked
Clear
f/1.5 light loss
Zero light loss
Unit Weight
1.70 lb (0.77 kg)
ELECTRICAL
Input Voltage*
Synchronization
12 VDC or 24 VAC ( 10%), autosensing
Internal or AC line lock
Power Consumption
Camera
<3 W (DW/CW models)
<4 W (DN/CH models)
Heaters
10 W when active, thermostatically controlled
*24 VAC power is recommended when installing any Camclosure Integrated Camera System under
fluorescent lighting conditions.
VIDEO
Signal System
NTSC or PAL
Video Output
Composite
UTP
1 Vp-p (75 ohms)
1 Vp-p (100 ohms)
Video Connectors
Service Connector
1 composite BNC and 1 UTP
3-conductor, 2.5 mm connector for video output to optional IS-SC cable
ENVIRONMENTAL
Environment
Low temperature, indoor/outdoor
Operating Temperature
Thermostat Operation
-50° to 122°F (-46° to 50°C); de-ices to 25°F (-4°C)
Heater is thermostatically controlled to activate ON at 50°F (10°C) and
OFF at 80°F (27°C)
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
29
CAMERA/LENS
(Design and product specifications subject to change without notice.)
5.48 (13.92)
3.50 (8.89)
1.75
(4.45)
2.42
(6.15)
3.75 (9.53)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;
ALL OTHERS ARE INCHES.
REVISION HISTORY
Manual #
C3427M
Date
2/07
5/07
7/07
10/07
2/09
Comments
Original version.
C3427M-A
C3427M-B
C3427M-C
C3427M-D
Updated switch setting and day/night operation descriptions.
Changed part name of service connector from ICS-SC to IS-SC per CN20476.
Revised illustrations for the threshold switching levels.
Added a lens focus procedure to Camera Adjustments.
30
C3427M-D (2/09)
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of
shipment.
Exceptions to this warranty are as noted below:
•
•
Five years:
–
–
–
Fiber optic products
TW3000 Series unshielded twisted pair (UTP) transmission products
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models
Three years:
–
–
–
–
–
Pelco-branded fixed camera models (CCC1390H Series, C10DN Series, C10CH Series, IP3701H Series, and IX Series)
EH1500 Series enclosures
Spectra® IV products (including Spectra IV IP)
Camclosure® Series (IS, ICS, IP) integrated camera systems
DX Series digital video recorders, DVR5100 Series digital video recorders, Digital Sentry® Series hardware products, DVX Series digital video
recorders, and NVR300 Series network video recorders
–
–
–
Endura® Series distributed network-based video products
Genex® Series products (multiplexers, server, and keyboard)
PMCL200/300/400 Series LCD monitors
•
Two years:
–
–
–
–
–
–
–
–
Standard varifocal, fixed focal, and motorized zoom lenses.
DF5/DF8 Series fixed dome products
Legacy® Series integrated positioning systems
Spectra III™, Spectra Mini, Spectra Mini IP, Esprit®, ExSite®, and PS20 scanners, including when used in continuous motion applications.
Esprit Ti and TI2500 Series thermal imaging products
Esprit and WW5700 Series window wiper (excluding wiper blades).
CM6700/CM6800/CM9700 Series matrix
Digital Light Processing (DLP®) displays (except lamp and color wheel). The lamp and color wheel will be covered for a period of 90 days.
The air filter is not covered under warranty.
–
Intelli-M® eIDC controllers
•
•
One year:
–
Video cassette recorders (VCRs), except video heads. Video heads will be covered for a period of six months.
Six months:
–
All pan and tilts, scanners, or preset lenses used in continuous motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent
freight prepaid to a Pelco designated location. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products.
Pelco’s liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to
the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental, or
consequential damages (including loss of use, loss of profit, and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state
to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and
provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product that does not fall under the warranty conditions stated above, please include a written
explanation with the product when returned.
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if
returned for credit, and RA number if returned for repair) and designated return location.
All merchandise returned for credit may be subject to a 20 percent restocking and refurbishing charge.
12-23-08
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc.
DLP is a registered trademark of Texas Instruments Incorporated.
All product names and services identified throughout this document are trademarks or registered trademarks of their respective companies.
The absence of a trademark or registered trademark from this document does not constitute a waiver of intellectual property rights.
© Copyright 2009, Pelco, Inc. All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
Pelco, Inc. Worldwide Headquarters 3500 Pelco Way Clovis, California 93612 USA
USA & Canada Tel (800) 289-9100 Fax (800) 289-9150
International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
|