OPERATION/PROGRAMMING
Spectra® Mini Dome
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Welcome. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
5
How to Operate Your Dome System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessing Main Menu (Preset 95) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CM6700/CM6800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KBD200A/KBD300A (Direct Mode Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CM9500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CM9740/CM9760/CM9770/CM9780 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KBD4000/KBD4002 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MPT9500 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
NET300/NET350/NET4001A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WS5050 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VCD5000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6
7
7
7
7
7
8
8
8
8
8
Setup Menus – Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9
Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
System Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Display Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Label Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Dome Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Auto Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Zoom Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Zoom Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Preset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Advanced Camera Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Shutter Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
AGC Limit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Auto Iris . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Auto Sharpness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Auto White Balance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Backlight Compensation (BLC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Video Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Motion Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Auto Flip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Proportional Pan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Park Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Scan Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Limit Stops . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Azimuth Zero . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Power Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Power Up Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Line Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
C3403M-A (3/06)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Window Blanking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Reverse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Clear Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Blank All Above/Blank All Below . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Reset, Cycle Power, Reboot . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Reset Camera . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Cycle Camera Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Reboot System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Software/Language File Upload . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Upload Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
4
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Welcome
Thank you for purchasing Pelco’s Spectra® Mini dome system. Your new system features a high resolution, color camera/optics
package and programmable dome drive software.
This manual is designed to be a reference tool for the operation and programming of your system. Inside you will find information
about Spectra Mini’s features and commands, as well as a detailed menu tree.
GETTING STARTED
You will need to install your dome system before using this manual. Refer to the installation manual.
Once installed apply power to the Spectra Mini dome system. The system will start a
configuration sequence. When configuration is done, the following information is displayed:
PELCO SPECTRA MINI
VERSION X.XX
D ADDRESS: NONE
P ADDRESS: 1
COMM 4800, N, 8, 1
CONFIGURE DONE
This information will remain on the monitor until dome operation begins.
Refer to the following pages to learn how to operate and program your dome system.
C3403M-A (3/06)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
How to Operate Your Dome System
Operation
How to Control
Pan and Tilt
Move joystick or press the direction keys left/right and up/down.
Zoom Far
To zoom far, do the following:
1. Press the Zoom Tele button or turn the joystick clockwise until zoom stops at the 32X zoom limit.
2. Release the button or joystick for one second.
3. To continue zooming (digitally), press the button or turn the joystick clockwise again until you have the
picture you want or reach the digital zoom1 limit.
Zoom Wide
Press the Zoom Wide button or turn the joystick counterclockwise.
Scanning
Stop Scan
Preset 96
Preset 97
Preset 98
Preset 99
Random Scan
Frame Scan
Auto Scan
Preset
Refer to the documentation supplied with the control system.
Pattern2
Zones
Refer to the documentation supplied with the control system.
Refer to the Zones section and to the documentation supplied with the control system.
Turn on or off in the programming menu. Refer to the Auto Flip section in this manual.
Auto Flip
1 Digital zoom magnifies the image electronically and the picture may appear pixilated. The larger the digital zoom limit the
greater the reduction in resolution.
2 The dome cannot do digital zoom in a pattern. Optical zoom will operate in a pattern.
6
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSING MAIN MENU (Preset 95)
You can call up the main menu on your monitor by programming (setting or creating) preset 95
(preset 28 if in AD32-preset mode).
Programming preset 95 for Pelco’s controllers varies according to the type of controller you are
using. Instructions for programming preset 95 are given below for various Pelco controllers.
CM6700/CM6800
1. Enter the number of the Spectra dome system and press the CAM key.
2. Enter 95 and hold the PRESET key for two seconds.
3. In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.
KBD200A/KBD300A (DIRECT MODE ONLY)
1. Enter 95.
2. Hold the PRESET key (approximately five seconds) until the main menu appears on the
screen.
CM9500
1. Enter the number of the Spectra dome system and press the CAM key. The Main menu
appears.
2. Highlight SETUP in the Main menu and press the SELECT key.
3. Highlight CAM in the Setup menu and press the SELECT key.
4. Highlight PRESET in the Camera menu and press the SELECT key.
5. Enter 95 and press the F1 key. The main menu appears.
CM9740/CM9760/CM9770/CM9780
1. Press the ESCAPE key to open the Main menu. Select DEF. The Define Submenu
appears.
2. Enter your four-digit PIN if this is your first time entering this mode.
3. Enter 95 and select PRST. The main menu appears on the monitor.
4. Select the Quit icon to return to the default menu.
(Continued on next page)
C3403M-A (3/06)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
KBD4000/KBD4002
1. Press the SPOT MONITOR key.
2. Enter 95, then hold the PRESET key (approximately five seconds) until the main menu
appears on the screen.
MPT9500
Standard Coaxitron Mode
1. Enter 95 and press the PRESET SET key.
2. Position the asterisk in the YES row and press the F1 key. The main menu appears.
Extended Coaxitron or RS-485 Mode
1. Enter 95 and press the PRESET SET key.
2. Press the F2 key. The main menu appears.
NET300/NET350/NET4001A
1. Check the Set box.
2. Click the preset 95 button. The main menu appears.
WS5050
1. Right-click in the video pane of the Spectra dome system.
2. Click Preset and then click Select Preset.
3. Enter 95 and then click OK.
VCD5000
1. Enter 95 for the preset action. The shortcuts menu appears.
2. Press the Preset button on the KBD5000.
8
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup Menus – Overview
PELCO SPECTRA MINI
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
SYSTEM INFORMATION
DOME SETTINGS
DISPLAY SETUP
PRESET LABEL
ZONE LABEL
ZOOM
2 (SECS)
2 (SECS)
2 (SECS)
2 (SECS)
OFF
DOME DRIVE MODEL
SOFTWARE VERSION
BIOS VERSION
FONT VERSION
COMM
MINI 114R
XX.X
<CAMERA>
<MOTION>
XX.X
<POWER UP>
<LINE SYNC>
<PRESETS>
AZIMUTH/ELEVATION
DIRECTION
XX.X
4800, N, 8, 1
NONE
1
D ADDRESS
<PATTERN>
P ADDRESS
<LABEL POSTIONS>
RESTORE FACTORY DEFAULTS
<ZONES>
CM9500 MODE
32 PRESETS
OFF
<WINDOW BLANKING>
<CLEAR>
OFF
PROTOCOL
P
<PASSWORD>
<ADDITIONAL>
BACK
EXIT
BACK
EXIT
BACK
EXIT
ADDITIONAL
[ZONE LABEL-------]
[PRESET LABEL-------]
SEE NEXT PAGE
FREE MEMORY
LAST RESET
XXXXX
X
AZIMUTH ZERO OFFSET
MOTOR ACTIVE
CAMERA ACTIVE
FPGA VERSION
VIDEO LEVEL
0O
YES
YES
X
HIGH
SAVE AND EXIT
CANCEL AND EXIT
HELP
CAMERA
XXXX-XXXX
ENGLISH X.XX
LANGUAGE 1
XXXO/-XXO
NE
XXX.XX
ITALIANO X.XX
LANGUAGE 6
BACK
EXIT
Quick Programming Guide
Access main menu (preset 95). See the Accessing Main Menu (Preset 95) section.
Use the joystick to position the cursor beside menu selection.
If your controller does not have a joystick, use the up or down key.
Press Iris Open, the submenu/cursor moves to the right.
Move the joystick up or down to view selections.
Press Iris Open to make selection.
Press Iris Close to cancel selection.
C3403M-A (3/06)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED SETTINGS
SHUTTER SPEED
DOME SETTINGS
CAMERA
AUTO
29
ON
X80
MEDIUM
FOCUSED
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
<CAMERA>
AGC LIMIT
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
AUTO IRIS
AUTO IRIS LEVEL
AUTO IRIS PEAK
AUTO SHARPNESS
SHARPNESS LEVEL
AUTO WHITE BALANCE
R GAIN
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
AUTO
76
16
<ADVANCED SETTINGS>
<PATTERN>
ON
<ZONES>
26
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
ON
402
678
OFF
HIGH
BACK
EXIT
BACK
EXIT
MOTION
AUTO FLIP
ON
ON
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
0
NONE
6
SCAN SPEED (DEG/S)
LIMIT STOPS
ON
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
POWER UP
POWER UP ACTION
NONE
BACK
EXIT
LINE SYNC
LINE SYNC
LINE SYNC PHASE
ON
0
BACK
EXIT
PRESETS
PRESET NUMBER
1
* * * PRESET NOT DEFINED * * *
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<CLEAR PRESET>
BACK
EXIT
REFERENCE INFORMATION
AZIMUTH
-
-
-
ELEVATION
ZOOM
CONTINUED ON NEXT PAGE
10
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
FROM
PREVIOUS
PAGE
PATTERN
<PROGRAM PATTERN>
<CLEAR PATTERN>
BACK
EXIT
REFERENCE INFORMATION
PATTERN USAGE
REMAINING
0%
100%
ZONES
ZONE NUMBER
1
* * * ZONE NOT DEFINED * * *
<EDIT ZONE LABEL>
<EDIT ZONE>
NO
OFF
ZONE ENABLED
ZONE BLANKING
<CLEAR ZONE>
BACK
EXIT
WINDOW BLANKING
STYLE
SET WINDOW
GRAY
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
BLANK ALL ABOVE
BLANK ALL BELOW
OFF
OFF
ENABLE WINDOW
REVERSE
NO
<SET WINDOW>
CLEAR WINDOW
BACK
EXIT
BACK
EXIT
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR PATTERN
CLEAR ALL WINDOW BLANKING
RESTORE FACTORY DEFAULTS
BACK
EXIT
PASSWORD
ENABLE PASSWORD
<EDIT PASSWORD>
EDIT THE PASSWORD
----------
OFF
1234567890
OK
ABCDEFGHIJ
KLMNOPQRST
UVWXYZ.,-/
CANCEL
SPACE
BACK
EXIT
BACKSPACE
abcdefghij
klmnopqrst
uvwxyz#&:*
C3403M-A (3/06)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Language
The language for the on-screen menus is selectable. Available languages include English,
Spanish, French, German, Italian, Portuguese, Russian, Polish, Turkish, and Czechoslovakian.
The factory default language is English.
PELCO SPECTRA MINI
LANGUAGE
ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
NOTE: The dome system cannot store all 10 languages in its memory. There are two language
packages available. The standard language package includes English, Spanish, Portuguese,
Italian, French, and German. The alternate package includes English, Russian, Polish, Turkish,
and Czechoslovakian. If your dome system does not have the language package that you require,
you must upload the other language package. Refer to the Software/Language File Upload
section.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
To change the display language:
1. Use the joystick to position the cursor beside LANGUAGE.
2. Press Iris Open. The cursor moves to the right, beside the current, selected language.
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.
All on-screen menus are changed to the selected language.
12
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
System Information
The system Information screen displays dome drive model, software version, and other
PELCO SPECTRA MINI
diagnostic information.
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
System settings cannot be changed using this screen. This screen is for reference only.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
Use the following steps to display the System Information screen:
1. Use the joystick to position the cursor beside SYSTEM INFORMATION.
2. Press Iris Open. The SYSTEM INFORMATION window opens.
EXIT
SYSTEM INFORMATION
DOME DRIVE MODEL
SOFTWARE VERSION
BIOS VERSION
MINI 114R
XX.X
XX.X
XX.X
FONT VERSION
COMM
4800, N, 8, 1
D ADDRESS
P ADDRESS
CM9500 MODE
32 PRESETS
PROTOCOL
NONE
1
OFF
OFF
P
<ADDITIONAL>
BACK
EXIT
ADDITIONAL
FREE MEMORY
LAST RESET
XXXXX
X
AZIMUTH ZERO OFFSET
CAMERA ACTIVE
FPGA VERSION
VIDEO LEVEL
0.00o
YES
X
HIGH
CAMERA
XXXX-XXXX
LANGUAGE 1
LANGUAGE 2
ENGLISH X.XX
ESPANOL X.XX
LANGUAGE 3
LANGUAGE 4
LANGUAGE 5
LANGUAGE 6
PORTUGUES X.XX
DEUTSCH X.XX
FRANCAIS X.XX
ITALIANO X.XX
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Display Setup
Display setup allows you to program how labels are displayed on the monitor. The following
labels are available:
PELCO SPECTRA MINI
LANGUAGE
ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
PRESET LABEL
ZONE LABEL
Identifies preset.
Identifies zone.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
ZOOM RATIO
AZIMUTH1/ELEVATION2
Identifies the amount of magnification.
Amount of pan from 0° and the amount of tilt from 0° horizontal.
Displays compass direction.
DIRECTION
EXIT
A preset label is displayed when a preset is called. A zone label is displayed when the system
moves into a zone. The zoom ratio label is displayed when zoom is activated. Azimuth/elevation
and direction labels are displayed when pan/tilt is activated.
DISPLAY SETUP
PRESET LABEL
ZONE LABEL
ZOOM
AZIMUTH/ELEVATION
DIRECTION
2 (SECS)
2 (SECS)
2 (SECS)
2 (SECS)
OFF
The following settings are available for each label:
OFF
Label is not displayed when activated.
CONSTANT
2 SECONDS
5 SECONDS
10 SECONDS
The label is continually displayed when activated.
The label is displayed for 2 seconds after activation.
The label is displayed for 5 seconds after activation.
The label is displayed for 10 seconds after activation.
<LABEL POSITIONS>
RESTORE FACTORY DEFAULTS
BACK
EXIT
1 Azimuth is the pan angle from 0° to 359°.
2 Elevation is the tilt position from 0° (horizon) to -90°.
14
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
LABEL POSITION
Labels can be placed anywhere on the monitor. This feature allows you to customize the
appearance of your monitor screen.
PELCO SPECTRA MINI
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
The following labels are not set at fixed positions:
PRESET LABEL
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
ZONE LABEL
ALARM 1
EXIT
ZOOM RATIO - XXX.XX
AZIMUTH1/ELEVATION2 - XXX°/-XX°
DIRECTION - NE
DISPLAY SETUP
To set a label position:
PRESET LABEL
ZONE LABEL
ZOOM
AZIMUTH/ELEVATION
DIRECTION
2 (SECS)
2 (SECS)
2 (SECS)
2 (SECS)
OFF
1. Use the joystick to position the cursor beside a label.
2. Press Iris Open.
3. Use the joystick to move the label up, down, left, and/or right.
4. Press Iris Open.
<LABEL POSITIONS>
RESTORE FACTORY DEFAULTS
5. Repeat steps 1 through 4 to position other labels.
6. Position the cursor next to Save and Exit. Press Iris Open to save settings and exit menu.
BACK
EXIT
1 Azimuth is the pan angle from 0° to 359°.
2 Elevation is the tilt position from 0° (horizon) to -90°.
[ZONE LABEL-------]
[PRESET LABEL-------]
SAVE AND EXIT
CANCEL AND EXIT
HELP
XXX°/-XX°
NE
XXX.XX
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dome Settings
CAMERA
AUTO FOCUS
PELCO SPECTRA MINI
LANGUAGE ENGLISH
Auto focus allows the lens to remain in focus during zoom-in, zoom-out, and motion functions.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
There are two auto focus settings:
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
ON (default)
If auto focus mode is set to ON, the camera will focus automati-
cally when using pan, tilt, and zoom functions.
OFF
Focus is operated manually. To focus, press the Focus Far or Focus
Near button on the controller.
EXIT
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
CAMERA
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
ON
X80
MEDIUM
FOCUSED
<ADVANCED SETTINGS>
BACK
EXIT
16
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
ZOOM LIMIT
PELCO SPECTRA MINI
LANGUAGE ENGLISH
Zoom limit allows the user to define a limitation on the amount of telephoto zoom. The default
setting is 80X.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
Zoom (10X optical zoom and 8X digital zoom) can be set for 10X, 32X, 40X, or 80X.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
ZOOM SPEED
EXIT
Zoom speed allows the user to define how fast the dome will go from full wide zoom to the 10X
optical zoom. The default setting is MEDIUM.
Available settings for zoom speed include the following:
DOME SETTINGS
HIGH
1.5 seconds
2.5 seconds
4.3 seconds
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
MEDIUM (default)
LOW
<PATTERN>
<ZONES>
NOTE: When using the HIGH setting, the image may be out of focus until zooming stops.
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
PRESET
This option determines how fast the dome will travel to a preset position and whether the dome
will stay in focus while moving.
BACK
EXIT
FOCUSED
FAST
Maintains focus when going to a preset position.
Travels quicker to a preset position and then focuses.
CAMERA
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
ON
X80
MEDIUM
FOCUSED
<ADVANCED SETTINGS>
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED CAMERA SETTINGS
SHUTTER SPEED
PELCO SPECTRA MINI
LANGUAGE ENGLISH
Shutter speed is the duration of the electronic shutter. Program shutter speed to operate
automatically (Auto) or manually (Numeric Value).
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
AUTO (default)
The electronic shutter speed is set automatically by the amount of
light sensed by the camera.
EXIT
NUMERIC VALUE
Spectra Mini system has several numerical shutter speed
settings. The higher the number, the faster the electronic shutter.
DOME SETTINGS
The slowest shutter speed setting is 60 = 1/60 second
The fastest setting is 30,000 = 1/30,000 second
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
Increasing the shutter speed lowers the light sensitivity and
reduces the streaking of fast moving objects.
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
NOTE: Set the shutter speed to 100 if you are using an NTSC camera in a 50 Hz environment.
This will eliminate any flicker that may occur in the picture.
BACK
EXIT
AGC LIMIT
The AGC (automatic gain control) Limit adjusts the brightness of the pictures. Settings ranges
from 0 to 40. The brightness increases as the number gets higher.
CAMERA
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
ON
X80
MEDIUM
FOCUSED
<ADVANCED SETTINGS>
BACK
EXIT
ADVANCED SETTINGS
SHUTTER SPEED
AUTO
29
AGC LIMIT
AUTO IRIS
AUTO
76
AUTO IRIS LEVEL
AUTO IRIS PEAK
16
AUTO SHARPNESS
SHARPNESS LEVEL
ON
26
AUTO WHITE BALANCE
R GAIN
ON
402
678
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
OFF
HIGH
BACK
EXIT
18
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
AUTO IRIS
PELCO SPECTRA MINI
LANGUAGE ENGLISH
Auto iris is the lens function that automatically opens and closes the iris in response to changing
light conditions.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
Program the auto iris to operate automatically or at a user-defined level.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
OFF
Auto iris is disabled, and control is always manual.
AUTO (default)
The iris is adjusted automatically to produce a constant video
output as determined by the Auto Iris Level setting.
EXIT
NOTE: If auto iris is in the auto mode, it will remain that way until the iris is manually opened
or closed. The dome will return to auto mode when it is panned or tilted more than 15 degrees.
DOME SETTINGS
Auto Iris Level
<CAMERA>
<MOTION>
Auto iris level is the numeric value the auto iris uses to maintain the brightness level of the
camera. Increase the value to brighten the scene. Decrease the level to darken the scene. This
setting can be adjusted if the video level in the auto iris mode is too bright or too dark.
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
NOTE: If backlight compensation is ON, decrease the Auto Iris Level setting.
<PASSWORD>
Auto Iris Peak
Increasing the peak value will cause the auto iris circuit to react more to highlights or “peaks” in
the picture. Decreasing this value will cause it to use the average video level to adjust the iris.
BACK
EXIT
CAMERA
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
ON
X80
MEDIUM
FOCUSED
<ADVANCED SETTINGS>
BACK
EXIT
ADVANCED SETTINGS
SHUTTER SPEED
AUTO
29
AGC LIMIT
AUTO IRIS
AUTO
76
AUTO IRIS LEVEL
AUTO IRIS PEAK
16
AUTO SHARPNESS
SHARPNESS LEVEL
ON
26
AUTO WHITE BALANCE
R GAIN
ON
402
678
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
OFF
HIGH
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
PELCO SPECTRA MINI
LANGUAGE ENGLISH
AUTO SHARPNESS
Auto sharpness enhances picture detail by increasing the aperture gain of the camera and
sharpening the edges in the picture.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
There are two settings:
ON (default)
The camera automatically maintains a normal sharpness mode.
EXIT
OFF
The sharpness of the picture is set manually by programming the
SHARPNESS LEVEL. Sharpness level settings range from 0-31.
AUTO WHITE BALANCE
DOME SETTINGS
This feature automatically processes the viewed image to retain color balance over a color
temperature range. The default setting for auto white balance is ON.
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
R GAIN
Adjusts the picture output in the red range. As you change the
value, you will see the color change on your monitor.
<PASSWORD>
B GAIN
Adjusts the picture output in the blue range. As you change the
value, you will see the color change on your monitor.
BACK
EXIT
CAMERA
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
ON
X80
MEDIUM
FOCUSED
<ADVANCED SETTINGS>
BACK
EXIT
ADVANCED SETTINGS
SHUTTER SPEED
AUTO
29
AGC LIMIT
AUTO IRIS
AUTO
76
AUTO IRIS LEVEL
AUTO IRIS PEAK
16
AUTO SHARPNESS
SHARPNESS LEVEL
ON
26
AUTO WHITE BALANCE
R GAIN
ON
402
678
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
OFF
HIGH
BACK
EXIT
20
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
BACKLIGHT COMPENSATION (BLC)
PELCO SPECTRA MINI
LANGUAGE ENGLISH
If a bright backlight is present, the subjects in the picture may appear dark or as a silhouette.
Backlight compensation enhances objects in the center of the picture. The dome uses the center
of the picture to adjust the iris. If there is a bright light source outside of this area, it will wash
out to white. The camera will adjust the iris so that the object in the sensitive area is properly
exposed.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
There are two backlight compensation settings:
ON
Backlight compensation is activated.
OFF (default)
Backlight compensation is not activated.
NOTE: If backlight compensation is ON, decrease the Auto Iris setting. Refer to the Auto Iris
DOME SETTINGS
section.
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
VIDEO LEVEL
Set the video output to one of the following:
NORMAL
1.0 volt peak-to-peak
HIGH (default setting)
1.2 volt peak-to-peak to compensate for losses in video cable.
BACK
EXIT
CAMERA
AUTO FOCUS
ZOOM LIMIT
ZOOM SPEED
PRESET
ON
X80
MEDIUM
FOCUSED
<ADVANCED SETTINGS>
BACK
EXIT
ADVANCED SETTINGS
SHUTTER SPEED
AUTO
29
AGC LIMIT
AUTO IRIS
AUTO
76
AUTO IRIS LEVEL
AUTO IRIS PEAK
16
AUTO SHARPNESS
SHARPNESS LEVEL
ON
26
AUTO WHITE BALANCE
R GAIN
ON
402
678
B GAIN
BACKLIGHT COMP
VIDEO LEVEL
OFF
HIGH
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MOTION SETTINGS
AUTO FLIP
PELCO SPECTRA MINI
LANGUAGE ENGLISH
When the camera tilts downward and goes just beyond the vertical position, the dome rotates
180 degrees. When the dome rotates (flips), the camera starts moving upward as long as you
continue to hold the joystick in the down position. Once you let go of the joystick after the dome
rotates, joystick control returns to normal operation. The auto flip feature is useful for following
a person who passes directly beneath the dome.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
There are two auto flip modes:
ON (default)
OFF
Auto flip mode is enabled.
Auto flip mode is disabled.
DOME SETTINGS
PROPORTIONAL PAN
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
Proportional pan automatically reduces or increases the pan and tilt speeds in proportion to the
amount of zoom. At telephoto zoom settings, the pan and tilt speeds will be slower for a given
amount of joystick deflection than at wide zoom settings. This keeps the image from moving too
fast on the monitor when there is a large amount of zoom.
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
There are two proportional pan modes:
ON (default)
OFF
Enables the proportional pan mode.
Disables proportional pan mode. The pan speed will not depend
on the amount of zoom.
BACK
EXIT
MOTION
AUTO FLIP
ON
ON
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
0
NONE
6
SCAN SPEED (DEG/S)
LIMIT STOPS
ON
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
REFERENCE INFORMATION
MANUAL LIMITS SET
SCAN LIMITS SET
NO
NO
22
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARK TIME
PELCO SPECTRA MINI
LANGUAGE ENGLISH
This feature allows the dome to begin preset 1 after a programmed time of inactivity.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
Park time can be programmed from 1 minute to 720 minutes (12 hours), or it can be set to zero,
which disables this feature. The default setting is zero.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
Park Action
EXIT
This feature will define the activity when the dome parks. The following settings are available:
NONE (default)
No action.
PRESET 1
Dome goes to preset 1.
DOME SETTINGS
SCAN SPEED
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
Scan speed is the degrees per second that the dome will pan when in a scan mode. Scan speed
is adjustable for 3, 6, or 12 degrees per second through the programming menu. The default
setting is 6 degrees per second.
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
MOTION
AUTO FLIP
ON
ON
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
0
NONE
6
SCAN SPEED (DEG/S)
LIMIT STOPS
ON
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
REFERENCE INFORMATION
MANUAL LIMITS SET
SCAN LIMITS SET
NO
NO
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
23
Download from Www.Somanuals.com. All Manuals Search And Download.
LIMIT STOPS
PELCO SPECTRA MINI
LANGUAGE ENGLISH
Limit stops are programmable stops that limit the pan range of the dome. There must be two
limits, a left and a right, to define an area.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
There are two types of limit stops:
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
MANUAL
A manual (joystick) pan operation stops when a limit stop is
reached.
EXIT
SCAN
The dome reverses direction during random, frame, or auto
scanning when a limit stop is reached.
To set manual or scan stops:
DOME SETTINGS
1. Use the joystick to position the cursor beside SET MANUAL STOPS or SET SCAN STOPS.
2. Press Iris Open.
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
3. Follow the directions displayed on the monitor.
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
NOTE: In order for the manual or scan stops to work, the LIMIT STOPS setting must be ON.
To clear manual or scan stops:
1. Use the joystick to position the cursor beside CLEAR MANUAL STOPS or CLEAR SCAN
STOPS.
2. Press Iris Open.
BACK
EXIT
3. Follow the directions displayed on the monitor.
MOTION
AUTO FLIP
ON
ON
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
0
NONE
6
SCAN SPEED (DEG/S)
LIMIT STOPS
ON
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
REFERENCE INFORMATION
MANUAL LIMITS SET
SCAN LIMITS SET
NO
NO
24
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
AZIMUTH ZERO
PELCO SPECTRA MINI
LANGUAGE ENGLISH
Azimuth is the pan angle from 0° to 359°. Azimuth zero is the pan position you specify to be the
0° point. Azimuth zero is normally set to magnetic north. Once set, azimuth and compass
readings are based on the set Azimuth Zero point.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
To program azimuth zero:
1. Use the joystick to position the cursor beside SET AZIMUTH ZERO.
2. Press Iris Open.
EXIT
3. Follow the directions displayed on the monitor.
To clear azimuth zero:
DOME SETTINGS
1. Use the joystick to position the cursor beside CLEAR AZIMUTH ZERO.
2. Press Iris Open.
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
3. Follow the directions displayed on the monitor.
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
MOTION
AUTO FLIP
ON
ON
PROPORTIONAL PAN
PARK TIME (MINUTES)
PARK ACTION
0
NONE
6
SCAN SPEED (DEG/S)
LIMIT STOPS
ON
<SET MANUAL STOPS>
<CLEAR MANUAL STOPS>
<SET SCAN STOPS>
<CLEAR SCAN STOPS>
<SET AZIMUTH ZERO>
<CLEAR AZIMUTH ZERO>
BACK
EXIT
REFERENCE INFORMATION
MANUAL LIMITS SET
SCAN LIMITS SET
NO
NO
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
25
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER UP
POWER UP ACTION
This setting defines a specific activity (scan, preset, pattern) to be performed in the event the
power to the dome is cycled.
PELCO SPECTRA MINI
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
The following settings are available:
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
NONE
No action.
AUTO (default)
The dome resumes its prior activity or direction before the power
outage.
EXIT
AUTO SCAN
RANDOM SCAN
FRAME SCAN
PRESET 1
Dome starts auto scan operation.
Dome starts random scan operation.
Dome starts frame scan operation.
Dome goes to preset 1.
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
PRESET 8
Dome goes to preset 8.
PATTERN 1
Dome runs pattern 1.
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
POWER UP
POWER UP ACTION
AUTO
BACK
EXIT
26
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
LINE SYNC
Line sync refers to a programmable function that allows you to synchronize all cameras within a
PELCO SPECTRA MINI
matrix system.
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
NOTE: Spectra Mini automatically senses V-Sync input. No line sync setup is required for Pelco
control systems that provide a V-Sync signal.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
For matrix systems that do not output V-Sync, there are two settings for line synchronization:
ON (default)
Adjusts the phase of the line sync to synchronize input power.
LINE SYNC PHASE settings range from 0-359 degrees.
EXIT
OFF
The dome synchronizes to an internal clock.
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
LINE SYNC
LINE SYNC
LINE SYNC PHASE
ON
0
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
27
Download from Www.Somanuals.com. All Manuals Search And Download.
PRESETS
The Spectra Mini dome system has 64 preset positions. Each of the user-definable presets can
PELCO SPECTRA MINI
be programmed to use pan, tilt, camera settings, and motion detection. The programmable
presets are numbered 1-32 and 35-55.
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
The following presets are predefined for specific functions:
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
Preset
33
Action
EXIT
Flip command. Pans the dome drive 180 degrees.
34
Pan zero command. Directs the dome drive to the factory-
determined zero reference point.
90-91
92-93
95
Manual limit stops.
Scan limit stops.
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
Select main programming menu.
Stop a scan.
96
97
Random scanning.
Frame scanning.
<PATTERN>
<ZONES>
98
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
99
Start auto scanning.
Use the following steps to program a preset.
1. Select the preset number:
BACK
EXIT
a. Use the joystick to position the cursor beside PRESET NUMBER. Press Iris Open.
The cursor moves to the right.
b. Move the joystick up or down to view selections. Press Iris Open to enter
selection.
PRESETS
2. Edit the preset label:
PRESET NUMBER
1
a. Use the joystick to position the cursor beside EDIT PRESET LABEL.
b. Press Iris Open. The following appears on the monitor:
* * * PRESET NOT DEFINED * * *
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<CLEAR PRESET>
LABEL FOR PRESET
PRESET NUMBER ------
BACK
EXIT
1234567890
ABCDEFGHIJ
KLMNOPQRST
UVWXYZ.,-/
abcdefghij
OK
CANCEL
SPACE
REFERENCE INFORMATION
AZIMUTH
-
-
-
BACKSPACE
ELEVATION
klmnopqrst
uvwxyz#&:*
ZOOM
c. Use the joystick to position the cursor beside a character. Press Iris Open to enter
selection. To clear a character, position the cursor beside BACKSPACE, and then
press Iris Open.
d. When label is completed, move the cursor to OK. Press Iris Open to return to the
Preset menu.
28
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Edit the preset scene:
PELCO SPECTRA MINI
LANGUAGE ENGLISH
a. Use the joystick to position the cursor beside EDIT PRESET SCENE.
b. Press Iris Open.
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
c. Follow the directions displayed on the monitor.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
PRESETS
PRESET NUMBER
1
* * * PRESET NOT DEFINED * * *
<EDIT PRESET LABEL>
<EDIT PRESET SCENE>
<CLEAR PRESET>
BACK
EXIT
REFERENCE INFORMATION
AZIMUTH
-
-
-
ELEVATION
ZOOM
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
29
Download from Www.Somanuals.com. All Manuals Search And Download.
PATTERN
A pattern is a memorized, repeating, series of pan, tilt, zoom and preset functions that can be
PELCO SPECTRA MINI
recalled with a command from a controller or automatically by a programmed function (alarm,
park or power-up).
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
The Spectra Mini has one user-defined pattern. Pattern length is based upon memory usage
rather than a fixed amount of time. The complexity of the pattern will determine the amount of
storage available to program the pattern.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
To program a pattern:
1. Use the joystick to position the cursor beside PROGRAM PATTERN.
2. Press Iris Open. The Patterns programming window appears on the monitor.
3. Follow the directions displayed on the monitor.
DOME SETTINGS
<CAMERA>
<MOTION>
After the pattern is programmed, the amount of memory used is displayed on the screen.
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
To clear a pattern:
1. Use the joystick to position the cursor beside CLEAR PATTERN.
2. Press Iris Open.
3. Follow the directions displayed on the monitor.
NOTE: When programming one or more presets within a pattern, use the normal controller
commands to call a preset.
BACK
EXIT
PATTERN
<PROGRAM PATTERN>
<CLEAR PATTERN>
BACK
EXIT
REFERENCE INFORMATION
PATTERN USAGE
REMAINING
0%
100%
30
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
ZONES
A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. The Spectra
PELCO SPECTRA MINI
Mini dome system is capable of four zones, each with a 20-character label.
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
To program a zone:
1. Use the joystick to position the cursor beside ZONE NUMBER. Press Iris Open the cursor
moves to the right.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
2. Move the joystick up or down to view selections. Press Iris Open to enter selection.
3. Use the joystick to position the cursor beside EDIT ZONE.
EXIT
4. Press Iris Open. The Zone programming window appears on the monitor.
5. Follow the directions displayed on the monitor. After the left and right limit stops are
set, the Zones menu reappears with the ZONE ENABLED option set to YES.
DOME SETTINGS
To edit a zone label:
<CAMERA>
<MOTION>
1. Use the joystick to position the cursor beside EDIT ZONE LABEL.
2. Press Iris Open. The following appears on the monitor:
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
3. Use the joystick to position the cursor beside a character. Press Iris Open to enter
selection. To clear a character, position the cursor beside BACKSPACE, and then press
Iris Open.
4. When the label is completed, move the cursor the OK. Press Iris Open to return to the
Zones menu.
BACK
EXIT
LABEL FOR ZONE
ZONE NUMBER ------
1234567890
ABCDEFGHIJ
KLMNOPQRST
UVWXYZ.,-/
abcdefghij
OK
CANCEL
SPACE
BACKSPACE
ZONES
ZONE NUMBER
klmnopqrst
uvwxyz#&:*
1
* * * ZONE NOT DEFINED * * *
<EDIT ZONE LABEL>
To disable a zone (a zone is enabled automatically when it is programmed) or to blank a zone:
1. Move the cursor beside ZONE ENABLED or ZONE BLANKING.
<EDIT ZONE>
ZONE ENABLED
ZONE BLANKING
NO
OFF
2. Press Iris Open. The cursor moves to the right.
<CLEAR ZONE>
BACK
EXIT
3. Move the joystick up or down to view selections. Press Iris Open to enter selection.
To clear a zone:
1. Use the joystick to position the cursor beside CLEAR ZONE.
2. Press Iris Open. Follow the instructions on the screen.
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
WINDOW BLANKING
Window blanking allows a user to program one four-sided, user-defined area that cannot be
viewed by the operator of the dome system. The blanked area will move with pan and tilt
functions and automatically adjust in size as the lens zooms telephoto and wide.
PELCO SPECTRA MINI
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
If a preset scene has window blanking, the image on the screen is blanked out when a preset is
called. When the dome reaches the preset, the blanking is removed and the preset scene is
displayed.
EXIT
Spectra Mini has two style modes for window blanking, GRAY and SMEAR. If style is set to gray,
the blanked area is covered with a solid gray window. If smear is selected images behind the
window will be noticeable but not distinguishable.
DOME SETTINGS
<CAMERA>
<MOTION>
To set the window blanking area:
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
1. Use the joystick to position the cursor beside WINDOW BLANKING. Press Iris Open. The
WINDOW BLANKING menu appears on the screen.
2. Move the joystick to position the cursor beside SET WINDOW. Press Iris Open to enter.
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
3. Use the joystick to position the cursor beside EDIT
WINDOW LOCATION. Press Iris Open, and then follow the
instructions that appear on the screen. When all four
INSIDE CORNER
corners are set, the SET WINDOW menu reappears, the
blanked area is displayed, and the ENABLE WINDOW option is set to YES.
BACK
EXIT
NOTE: Use the inside corner of the window selection tool as a guide when selecting
the upper left, upper right, bottom right, and bottom left corners of the window.
WINDOW BLANKING
STYLE
GRAY
BLANK ALL ABOVE
BLANK ALL BELOW
OFF
OFF
<SET WINDOW>
BACK
EXIT
SET WINDOW
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
ENABLE WINDOW
REVERSE
NO
CLEAR WINDOW
BACK
EXIT
32
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
4. The blanked area can be programmed to turn on or off at a specified zoom point. To set
the zoom point:
PELCO SPECTRA MINI
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
a. Use the joystick to position the cursor beside EDIT WINDOW ZOOM, and then
press Iris Open.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
b. Zoom in to the point where you want window blanking to turn on. Press Iris Open
to set the zoom point.
EXIT
NOTE: Since the area is already blanked out, it may be difficult to determine when you
want window blanking to turn on. Reverse the window before setting the zoom point.
When finished reverse the window again to blank out the area.
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
Window Blanking Disabled
Window Blanking Enabled
NOTE: Increase the size of the window if any part of the blanked area is revealed during pan,
tilt, and zoom operations.
WINDOW BLANKING
STYLE
GRAY
BLANK ALL ABOVE
BLANK ALL BELOW
OFF
OFF
<SET WINDOW>
BACK
EXIT
SET WINDOW
<EDIT WINDOW LOCATION>
<EDIT WINDOW ZOOM>
ENABLE WINDOW
REVERSE
NO
CLEAR WINDOW
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
33
Download from Www.Somanuals.com. All Manuals Search And Download.
REVERSE
The blanked out area can be reversed to make it visible and the areas on both sides of it not visible. The areas above and below the
blanking area remain visible. Reversing the window a second time will return it to its original condition.
CLEAR WINDOW
The area that has been set for window blanking is cleared.
BLANK ALL ABOVE/BLANK ALL BELOW
Blank All Above and Blank All Below add additional flexibility to setting up privacy areas. These settings are ideal for applications
where a complete pan location needs to be blanked.
Blank All Above
Blank All Below
Blanks everything above a user-defined tilt angle. A blanked
band will appear at the top of the screen. The following
settings are available:
Blanks everything below a user-defined tilt angle. A blanked
circle will appear below the specified angle. The following
settings are available:
OFF (default) - No blanking
OFF (default) - No blanking
0
Blanks area from horizon to 2° below horizon
0
Blanks area from 2° to 92° below horizon
-10 Blanks area from horizon to 10° below horizon
-20 Blanks area from horizon to 20° below horizon
-30 Blanks area from horizon to 30° below horizon
-40 Blanks area from horizon to 40° below horizon
-50 Blanks area from horizon to 50° below horizon
-60 Blanks area from horizon to 60° below horizon
-70 Blanks area from horizon to 70° below horizon
-80 Blanks area from horizon to 80° below horizon
-10 Blanks area from 10° to 92° below horizon
-20 Blanks area from 20° to 92° below horizon
-30 Blanks area from 30° to 92° below horizon
-40 Blanks area from 40° to 92° below horizon
-50 Blanks area from 50° to 92° below horizon
-60 Blanks area from 60° to 92° below horizon
-70 Blanks area from 70° to 92° below horizon
-80 Blanks area from 80° to 92° below horizon
HORIZON
CAMERA
30
4
0
34
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
CLEAR
Use this setting to clear user-defined settings or return the dome to factory default settings.
PELCO SPECTRA MINI
LANGUAGE ENGLISH
The following are the available CLEAR settings:
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
ALL ZONES
Clears all zones. To clear a single zone, refer to the Zones
section.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
ALL PRESETS
Clears all presets. To clear a single preset, refer to the
Presets section.
EXIT
ALL PATTERNS
Clears the pattern.
ALL WINDOW BLANKING
RESTORE FACTORY DEFAULTS
Clears the blanked window area.
Restores all camera settings to factory default settings.
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
CLEAR
CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR PATTERN
CLEAR ALL WINDOW BLANKING
RESTORE FACTORY DEFAULTS
BACK
EXIT
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
35
Download from Www.Somanuals.com. All Manuals Search And Download.
PASSWORD
Spectra Mini features password protection to prevent unauthorized changes to the dome
PELCO SPECTRA MINI
settings. An operator can open the System Information and Display Setup screens, but cannot
access any of the Dome Settings menus.
LANGUAGE ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
Controller/keyboard commands cannot override password-protected settings. If a keyboard is
used to set a preset, pattern, or zone, the Enter Password screen appears on the monitor.
The password must be entered before programming can continue.
RESET CAMERA
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
At least one character must be entered to create a valid password.
DOME SETTINGS
<CAMERA>
<MOTION>
<POWER UP>
<LINE SYNC>
<PRESETS>
<PATTERN>
<ZONES>
<WINDOW BLANKING>
<CLEAR>
<PASSWORD>
BACK
EXIT
PASSWORD
ENABLE PASSWORD
<EDIT PASSWORD>
OFF
BACK
EXIT
EDIT THE PASSWORD
----------
1234567890
OK
CANCEL
ABCDEFGHIJ
KLMNOPQRST
UVWXYZ.,-/
SPACE
abcdefghij
klmnopqrst
uvwxyz#&:*
BACKSPACE
36
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
Reset, Cycle Power, Reboot
PELCO SPECTRA MINI
RESET CAMERA
Use this function to reset all camera settings to factory default parameters.
LANGUAGE
ENGLISH
<SYSTEM INFORMATION>
<DISPLAY SETUP>
<DOME SETTINGS>
CYCLE CAMERA POWER
RESET CAMERA
If the camera is not operating or if you lose camera control, cycle camera power. Cycling camera
power resets the camera but does not change any saved camera settings.
CYCLE CAMERA POWER
REBOOT SYSTEM
EXIT
REBOOT SYSTEM
Reboot the system if it is not operating or if there is no control. Rebooting the system will cycle
dome and camera power without changing programmed dome settings.
Quick Programming Guide
(See page 9)
C3403M-A (3/06)
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Software/Language File Upload
The six-pin data port underneath the trim ring of the dome system allows access for on-site
setup, testing, and uploading of revised operating software and language files. A Pelco field
service tool is required to perform these operations. Field service tools include Pelco’s remote
monitor kit (IPS-RMK) and remote monitor cable (IPS-CABLE), both of which must be used with
an adapter cable (IPS-MINIADPT).
For instructions on how to upload revised operating software and language files refer to the
Installation/Operation manual supplied with the field service tool.
NOTE: Only perform software uploads when necessary. Software uploads do not need to be
performed if the dome system is operating properly.
UPLOAD ICON
During a software/language file upload, an icon will appear on the monitor to indicate data is
being transferred to the Spectra dome system (refer to the figure below). The default setting for
data transmission is 115.2 KB per second. Noisy and long-run connections will slow the
transmission rate.
Upload Icon
38
C3403M-A (3/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
REVISION HISTORY
Manual #
C3403M
C3403M-A
Date
12/05
3/06
Comments
Orginal version.
Removed Preset Blanking from menu. Added text to Window Blanking section that screen is blanked out when a preset
is called.
Pelco, the Pelco logo, and Spectra are registered trademarks of Pelco.
© Copyright 2006, Pelco.
All rights reserved.
Download from Www.Somanuals.com. All Manuals Search And Download.
®
World Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
United States | Canada | United Kingdom | The Netherlands | Singapore | Spain | Scandinavia | France | Middle East
Download from Www.Somanuals.com. All Manuals Search And Download.
|