Pelco Security Camera C290M A 6 99 User Manual

®
DD08 Intercept Dome  
Series Fixed mount  
Installation/Operation Manual  
C290M-A (6/99)  
PELCO • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981  
FAX (800) 289-9150 or (1-559) 292-3827  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION/OPERATION MANUAL  
DD08 INTERCEPT DOME SERIES  
FIXED MOUNT  
1.0 WARNINGS  
Priortoinstallationanduseofthisproduct,thefollowing  
WARNINGS should be observed.  
4. After replacement/repair of this unit’s electrical  
components, conduct a resistance measurement  
betweenlineandexposedpartstoverifytheexposed  
parts have not been connected to line circuitry.  
1. Installation and servicing should only be done by  
qualifiedservicepersonnelandconformtoalllocal  
codes.  
5. The installation method and materials should be  
capable of supporting four times the weight of the  
enclosure, pan/tilt, camera and lens combination.  
2. Unless the unit is specifically marked as a NEMA  
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is  
designed for indoor use only and it must not be  
installed where exposed to rain and moisture.  
3. Only use replacement parts recommended by  
PELCO.  
The product bears the following marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TOREDUCETHERISKOFELECTRICAL  
SHOCK, DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information in this manual  
prior to installation and operation.  
PELCO Manual C290M-A (6/99)  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.0 SCOPE  
3.1 MODELS  
The information contained in this manual covers the  
DD08SeriesfixedmountfortheIDS08SeriesIntercept  
Domes.  
The model designator is DD08XXX, where each “X”  
represents a feature that is essential for operation.  
Example: DD08 E 3 0 Dome drive with SL and  
presets, variable pan speed,  
This manual pertains only to the fixed mount. Pro-  
ceed with installation of the fixed mount and the  
camera/lens once back box installation has been  
completed.  
and black opaque dome  
with smoked window  
3.0 DESCRIPTION  
Dome  
Pan Speed  
0 = None  
1 = 12°/sec  
2 = 24°/sec  
Dome  
Color  
0 = Blk  
Model Dome Drive  
DD08 A = Fixed  
mount  
The IDS08 Intercept Series of domes allow you to  
select any combination of available features to create a  
custom dome system. This integral system includes  
fixed mount or dome drive (pan/tilt), Coaxitron  
receiver/driver and factory installed camera/lens pack-  
age.  
opaque  
with  
smoked  
window  
B = 355°  
C = 360° SL 3 = Variable*  
D = 355° &  
Presets  
1 = Blk  
E = SL &  
Presets  
opaque  
with  
clear  
To facilitate this, we use a building-block approach in  
assembling the desired components to fulfill the job  
requirements. The blocks are broken into four sections.  
They are:  
window  
2 = Chrome  
3 = Gold  
1
2
3
4
Dome Drive (DD08)  
Dome Receiver/Driver (DRD08)  
Back Box (BB08)  
* 0 to >200°/sec  
Imager/Optics Package (IOP08)  
3.2 CERTIFICATIONS  
UL  
The dome system is shipped in two separate boxes:  
1 box containing the Back Box  
CE  
DD08A00  
DD08B10  
DD08B11  
DD08B20  
DD08B21  
DD08C20  
DD08C21  
DD08C30  
DD08D11  
DD08D20  
DD08E30  
DD08E31  
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1 box containing the Dome Drive, Dome, Dome  
Receiver/Driver (when ordered) and Imager/  
Optics Package (factory assembled)  
2
PELCO Manual C290M-A (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.0 INSTALLATION  
4.1.1 INSTALLING FIXED MOUNT  
4.1 FIXED MOUNT INSTALLATION AND  
REMOVAL  
To install the fixed mount:  
1. Turn off back box power switch, if applicable to  
your back box. (See Figure 1 for switch location.)  
CAUTION  
2. Remove the hairpin style safety pins from the two  
latches in the back box (see Figure 2).  
Switch the rocker style power switch  
in back box to the OFF position be-  
fore installing or removing fixed  
mount.  
3. Remove dome from fixed mount. This is only a  
pull apart procedure (refer to Figure 3.)  
4. Grasp the fixed mount with two hands as shown in  
Figure 4.  
No wiring interface is required between the back box  
and the fixed mount. All wiring connections are  
achieved when the mechanical connection of the  
fixed mount is made.  
5. While lifting the unit up into the back box, find the  
two (2) V-opening latches and two (2) guide pins  
at the rear of the back box (see Figure 5).  
Ensure the fixed mount will interface electrically with  
the back box you have chosen to use. Refer to the back  
box manual, C456M, if necessary.  
NOTE: Ensure that you install the fixed mount  
in correct rotation to the back box so that the  
electrical connector on top of fixed mount lines  
up with mating connector in back box (see Fig-  
ure 6).  
6. Upon locating the guide pins, wiggle the unit back  
and forth to ensure the guide pins are aligned with  
the two (2) Delrin bushings on the fixed mount. At  
that instant, push the mount up until the two (2) V-  
shaped latches engage and lock the mount in place  
(see Figure 7). Be sure the latches are completely  
closed by pulling down on the latch arm as a check.  
7. Insert the two hairpin style safety pins previously  
removed in step 2 into the latches to prevent inad-  
vertent release of fixed mount from the back box.  
8. Install camera/lens of choice, positioning onto  
mount with sufficient clearance for dome attach-  
ment.  
9. Remove lens cap.  
10. Install dome onto fixed mount (refer to Figure 3),  
aligning window slot of dome with lens.  
NOTE: The fixed mount may also be in-  
stalled/removed (or bicycled) with the camera/  
lens already installed on mount, if needed.  
PELCO Manual C290M-A (6/99)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 1. Back Box Power Switch Location  
Figure 3. Removing/Attaching Dome to Fixed  
Mount  
Figure 2. Removing Safety Pins  
Figure 4. Installing Fixed Mount  
4
PELCO Manual C290M-A (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.1.2 REMOVING FIXED MOUNT  
To remove the fixed mount:  
1. Remove the back box bezel/trim ring as described  
in back box manual, C456M, and the dome.  
2. Turn off back box power switch, if applicable to  
your model (see Figure 1).  
3. Remove the two hairpin style safety pins from the  
back box latches (see Figure 2).  
4. Open only one of the latches by pressing the latch  
arm with your finger.  
5. Grasp the unit with one hand to prepare for the 5-  
10 lb (2.27-4.54 kg) load. Now press open the other  
latch with your other hand and lower the fixed  
mount.  
L = Latch  
P = Pin  
NOTE: When handling the mount please treat  
it with care for there are components that could  
possibly bend or be damaged.  
Figure 5. Guide Pin/Latch Locations  
Fixed Mount Electrical Connector  
Back Box Mating Connector  
Figure 6. Fixed Mount/Back Box Electrical Interconnect  
PELCO Manual C290M-A (6/99)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.0 ADJUSTMENTS  
To adjust the horizontal and vertical position of the  
fixed mount perform the following steps:  
1. Remove dome as per instructions in Section 4.1.1,  
step 3.  
2. Loosen the horizontal positioning lock-down knob;  
then rotate mount to the desired position and re-  
tighten knob.  
3. Loosen the vertical positioning lock-down knob  
and adjust tilt table to desired position; then re-  
tighten knob.  
4. Attach the dome to the drive as described in Sec-  
tion 4.3, step 3, Camera/Lens Installation.  
Figure 7. Locking Fixed Mount in Place  
5.1 OPERATION  
Upon completion of the fixed mount and camera/lens  
installation and positioning adjustments of the fixed  
mount, the Intercept Dome is ready for operation.  
4.2 LENS WIRING  
Refer to back box manual, C456M, for wiring pinouts  
and wire lens according to manufacturers instructions .  
Reach into the back box and turn the power switch ON  
(if applicable to your back box).  
4.3 CAMERA/LENS INSTALLATION  
Install the camera/lens you have selected for use with  
the IDS08 series dome as follows:  
CAUTION  
Thefixedmountshouldneverbeinstalled  
or removed when power switch is in the  
ON position.  
1. Attach camera/lens to the tilt table using the 1/4-  
20 x 1/2" fastener (supplied), mounting through  
the tilt table into the camera. Only snug the fas-  
tener at this time to allow for camera/lens posi-  
tioning.  
Now attach the bezel or trim ring to the back box as  
shown in Figure 8. Align the three bezel pins with the  
large hole in the back box brackets; push the bezel up  
and rotate clockwise to latch.  
2. Connect camera power spade lugs and coax video  
cable.  
3. Ensure there is sufficient initial clearance between  
the camera/lens and dome as you carefully attach  
dome to fixed mount. Align the two (2) ball studs  
on the dome to the two (2) ball stud receivers on  
the fixed mount and push dome until a snapping  
sound occurs (refer to Figure 3).  
Installation of your Intercept Dome is now complete  
and dome is ready for operation.  
4. Position camera/lens and route wiring as neces-  
sary to achieve clearances. This procedure may re-  
quire removing and reattaching dome a few times  
to obtain correct position.  
5. After satisfactory clearances have been achieved,  
remove dome and tighten camera/lens fastener.  
6
PELCO Manual C290M-A (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.0 SPECIFICATIONS  
MECHANICAL  
Pan:  
360°movementinhorizontalplane  
Tilt:  
-90° movement from horizontal  
plane  
Approximate  
Camera/Lens  
Size:  
Maximum total length of camera/  
lens 6.50" (16.5 cm), including  
BNC cable connection to camera;  
max. lens width 4.50" (11.4 cm);  
max. lens height 3.25" (8.25 cm)  
Figure 8. Bezel Attachment  
Connectors  
Video:  
BNC  
Camera Power:  
Spade lugs  
6.0 CARE AND MAINTENANCE  
GENERAL  
Regularly scheduled maintenance will prolong the op-  
erational life and appearance of the equipment.  
Construction  
Fixed Mount:  
Aluminum with stainless steel  
hardware  
IMPORTANT  
Lower Dome:  
Acrylic hemisphere available in  
the following types:  
The acrylic dome is an optical surface.  
When cleaning the inner surface of the  
dome and viewing window, treat as care-  
fully as you would a fine camera lens.  
Black opaque with smoked win-  
dow (1 f-stop light loss)  
Donotuseliquidofanykindon  
coated inner surface of dome.  
Black opaque with clear window  
(virtually zero light loss)  
Chrome or Gold (2 f-stop light  
loss)  
If dust or other debris accumulates on the inside of the  
lower dome, remove with clean air pressure only. Com-  
pressed air cans are available from commercial photo-  
graphic equipment and supply dealers.  
Weight:  
2 lbs 4.8 oz. (1.04 kg).  
Clean the outer surface of the dome and the inner  
surface of the viewing window with a non-abra-  
sive cleaning cloth and anti-static cleaner that is safe for  
use on acrylic plastic. Do not use kerosene or similar  
substances that can scratch the surface.  
PELCO Manual C290M-A (6/99)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
8.0 EXPLODED ASSEMBLY DIAGRAM  
Figure 9. DD08 Fixed Mount Exploded Assembly Diagram  
8
PELCO Manual C290M-A (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8.1 MECHANICAL PARTS LIST  
The following parts list corresponds to the exploded assembly diagram in Figure 9.  
Item No.  
Quantity  
Description  
Part Number  
1
2
3
4
5
6
7
8
9
2
2
1
1
1
1
1
2
1
Bushing, delrin 3/8" ID x 5/8" OD  
Push nut, .625" OD  
Bracket, drive mount, upper  
Connector, receptacle, 25 position  
Bracket, spindle, fixed mount  
Tilt table, fixed mount  
Frame 8", fixed mount  
Pin, latch, dome drive  
Dome, 8-1/2", acrylic  
80010004  
80010011  
8004034COMP  
CON10J025Z41T  
8004037COMP  
8004021COMP  
8004022COMP  
8004145COMP  
Black opaque w/smoked viewing window  
Black opaque w/clear viewing window  
Chrome finish f/2  
Gold finish f/2  
Ball stud  
Knob, grey, 1/4-20 tapped  
Receiver, ball stud  
Pin, crimp, loose piece (not shown)  
(for use with item #4)  
80810011-0  
80810011-1  
80810011-2  
80810011-3  
PT180410000  
CM1610003  
PT180410001  
CON66107-2  
10  
11  
12  
13  
2
2
2
6
14  
1
Connector, BNC, crimp, for RG174 coax  
(not shown)  
CONCPM88-174  
8.2 ASSOCIATED HARDWARE  
Item No.  
Quantity  
Description  
Part Number  
A
B
C
D
E
F
G
H
I
2
1
1
2
4
2
4
4
2
2
1
1
Screw 1/4-20 x 1" flat hd phil, SS  
Screw 1/4-20 x 1" soc hd c/s,SS  
Nut, lock, hex, 1/4-20, nylon insert, SS  
Screw 6-32 x 3/8" pan hd phil, SS  
Washer, internal star #6, SS  
Screw 6-32 x 1/2" pan hd phil, SS  
Screw 8-32 x 1/2" pan hd phil, SS  
Washer, internal star #8, SS  
Screw 6-32 x 3/8" flat hd phil, black oxide  
Spacer, 1/4" hex x 1/2" L, 6-32 tapped  
Washer, fender, 1/4 x 1.5 x 14 ga, black oxide  
Washer, split lock, 1/4" SS  
ZH1/420X1.00SFS  
ZH1/420X1.00SS  
ZH1/420NUTCHN  
ZH6-32X.375SPP  
ZH6LWSIS  
ZH6-32X.500SPP  
ZH8-32X.500SPP  
ZH8LWSIS  
ZH6-32X.375BPF  
SPA8423  
ZH255X1.50X62  
ZH1/4LWSSL  
J
K
L
PELCO Manual C290M-A (6/99)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
9.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY AND RETURN INFORMATION  
WARRANTY  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Pelco will repair or replace, without charge, any merchandise proved defective in material  
or workmanship for a period of one year after the date of shipment.  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
• Five years on FT/FR8000 Series fiber optic products.  
• Three years on Genex® Series products (multiplexers, server, and keyboard).  
• Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera  
models, which have a five-year warranty.  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
Method of return shipment shall be the same or equal to the method by which the item  
was received by Pelco.  
RETURNS  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
In order to expedite parts returned to the factory for repair or credit, please call the factory  
at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if  
returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
• Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and Endura™ Series distributed network-based video products.months on DX  
Series digital video recorders, NVR300 Series network video recorders, EnduraSeries  
distributed network-based video products, and TW3000 Series twisted pair transmission  
products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods  
to:  
• One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Service Department  
Pelco  
• Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or  
accident are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting  
from the specific use or application made of the Products. Pelco’s liability for any claim,  
whether based on breach of contract, negligence, infringement of any rights of any party  
or product liability, relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special, incidental or  
consequential damages (including loss of use, loss of profit and claims of third parties)  
however caused, whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also  
have additional rights, which are subject to variation from state to state.  
® Pelco, the Pelco logo, Spectra, Esprit, Genex, Legacy, and Camclosure are registered trademarks of Pelco.  
™ Endura and ExSite are trademarks of Pelco.  
© Copyright 1999, Pelco. All rights reserved.  
10  
PELCO Manual C290M-A (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Security Camera C2506E User Manual
Philips Computer Drive SNU6500 User Manual
Philips Digital Camera SPC500NC User Manual
Philips Musical Table WACS7000 User Manual
Philips Telephone CD181 User Manual
Pioneer Cassette Player KEH P5900R User Manual
Pioneer DVD Player DVD 204 User Manual
Poulan Lawn Mower 163598 User Manual
Printronix Printer P7000 H User Manual
Profoon Telecommunicatie Cordless Telephone PDX 1400 User Manual