Pelco Security Camera C283M C User Manual

C283M-C (4/07)  
LWM41  
Legacy® Wall Mount  
IMPORTANT SAFETY INSTRUCTIONS  
1. Installation and servicing should only be done by qualified service personnel and conform to all local codes.  
2. Installation shall be done in accordance with all local and national electrical and mechanical codes utilizing only approved materials.  
3. Use only installation methods and materials capable of supporting four times the maximum specified load.  
4. Use stainless steel hardware to fasten the mount to outdoor surfaces.  
5. To prevent damage from water leakage when installing a mount outdoors on a roof or wall, apply sealant around the bolt holes between the mount and  
mounting surface.  
The product and/or manual may bear the following marks:  
WARNING: This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.  
Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.  
DESCRIPTION  
The LWM41 wall mount is designed for use with all Legacy® Series pan/tilts, giving your installation a very neat and attractive look. All Legacy Series  
mounts and optional adapters are finished in a textured gray polyester powder coat to match the pan/tilts and enclosures.  
The LWM41 wall mount may be directly attached to any vertical load-bearing structure, and can be used with the PA402 pole mount adapter, the CM400  
corner mount adapter, or the PP300L/PP301L/PP4348/PP400 adapter for parapet mounting applications. This mount will support up to 150 pounds (68 kg).  
The LWM41 may also be used with an optional integral receiver (refer to Optional Receiver Models on page 2).  
OPTIONAL ADAPTERS  
PP300L  
PP301L  
PA402  
PP400  
Parapet corner adapter mount for LWM41, mounts on rooftops and parapets, rotates 360 degrees, supports 175-pound (79.38 kg) load  
Parapet corner adapter mount for LWM41, mounts to the inside of parapets, rotates 360 degrees, supports 175-pound (79.38 kg) load  
Pole mount adapter for the LWM41, minimum pole diameter 3 inches (7.62 cm), mounting straps not supplied  
Parapet mount adapter, maximum parapet width 16 inches (40.64 cm)  
PP4348  
CM400  
Parapet mount for use with LWM41, mounts to rooftop or horizontal flat surface, supports 75-pound (34 kg) load  
Corner mount adapter, supports up to 150 pounds (68 kg)  
OPTIONAL ACCESSORIES  
LK4500 Optional lock kit for LWM41 wall mount arm access panel  
Download from Www.Somanuals.com. All Manuals Search And Download.  
To install any Legacy Series pan/tilt with the LWM41 mount:  
1. Route the pan/tilt pigtail wire connector through the hole of the mount.  
2. Place the pan/tilt on the mount, without the enclosure being attached to the pan/tilt. Be sure the factory-installed gasket is on the bottom of the pan/  
tilt spindle for protection (refer to Figure 1).  
3. Secure the pan/tilt to the mount using three 1/4-20 x 5/8-inch cap screws supplied with the mount (refer to Figure 1). Be sure to apply some form of  
thread locker (for example, Loctite®) to the screws. Use a 3/16-inch Allen wrench to tighten the screws.  
4. Connect the pan/tilt 37-position connector to the receiver.  
5. Close the access panel, making sure none of the cables or wires are interfering with the lid.  
6. Turn the lid fastener to secure the lid.  
18.75  
(47.6)  
4.50  
(11.4)  
21.87  
(55.5)  
6.50  
(16.5)  
7.42  
(18.8)  
VIEW FROM BOTTOM  
2.10  
(5.3)  
14.30  
(36.3)  
NOTE: SHOWN WITH ACCESS PANEL  
OPEN AND RX BOX ATTACHED.  
1.49  
(3.8)  
2.40  
(6.1)  
6.83  
(17.3)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;  
ALL OTHERS ARE INCHES  
Figure 2. LWM41 Dimension Drawing  
Figure 1. Pan/Tilt Mounting  
SERVICE MANUAL  
If you need replacement parts, obtain a service manual in one of the following ways:  
Contact Pelco’s Literature Department and request service manual C283SM.  
SPECIFICATIONS  
Material  
Finish  
Aluminum casting and sheet metal  
Textured gray, polyester powder coat  
NEMA Rating  
Maximum Load  
Weight  
Meets NEMA Type 4 standards (with all factory-supplied gaskets and block-off plates installed)  
150 lb (68 kg)  
9.51 lb (4.31 kg)  
14 lb (6.35 kg) approximate with receiver installed  
(Design and specifications are subject to change without notice.)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
Exceptions to this warranty are as noted below:  
1. Model and serial number  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted  
pair transmission products.  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Three years on Spectra® IV products.  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product when  
returned.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed  
dome products.  
Two years on Spectra III, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for  
credit, and RA number if returned for repair).  
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays.  
The lamp and color wheel will be covered for a period of 90 days. The air filter is not  
covered under warranty.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed  
to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product lia-  
bility, relating to the Products shall not exceed the price paid by the Dealer to Pelco for such  
Products. In no event will Pelco be liable for any special, incidental or consequential damages  
(including loss of use, loss of profit and claims of third parties) however caused, whether by  
the negligence of Pelco or otherwise.  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual #  
C283M  
Date  
9/95  
12/95  
1/97  
5/97  
8/97  
Comments  
Original manual.  
Manual revised to include updated LWM41RETRO kit information in Section 4.3. Product load rating changed to 150 pounds (68 kg).  
In Section 4.0 and paragraph 3 of Section 4.3 changed the part descriptions for the cap screws and flat washers.  
Revision A. Revised to include new LRD41C21/C22 Series receivers. Mechanical parts list updated.  
Added the PP300L and PP301L parapet corner adapter mounts. Revised installation instructions, exploded aseembly diagram, and mechanical parts list. Changed  
description of cap screws that are supplied as loose equipment to install the pan/tilt unit.  
Reformatted document. Removed obsolete product information (LWM41RETRO).  
C283M-A  
C283M-B  
C283M-C  
4/07  
Worldwide Headquarters • 3500 Pelco Way • Clovis, California 93612 USA • www.pelco.com  
USA & Canada • Tel: 800/289-9100 • Fax: 800/289-9150  
International • Tel: 1-559/292-1981 • Fax: 1-559/348-1120  
Pelco, the Pelco logo, Camclosure, Coaxitron, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2007, Pelco. All rights reserved  
DLP is a registered trademark of Texas Instruments, Inc.  
Loctite is a registered trademark of Henkel KG&A, its subsidiaries, affiliates, licensors, or joint ventrue partners.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips Computer Monitor 107F User Manual
Philips Headphones SHI6601 User Manual
Philips Telephone SJA9190 17 User Manual
Phoenix Gold Speaker ISM4 User Manual
Pioneer Flat Panel Television PDP 504CMX User Manual
Planar Computer Monitor PL1911MW User Manual
Planet Technology Network Router WAP 4030A User Manual
Poulan Chainsaw PP4620AVL User Manual
Poulan Lawn Mower 177937 User Manual
Prima Stereo System WS 1424 E User Manual