Pelco Security Camera C1489M E 01 01 User Manual

C1489M-E (01/01)

DD5 Series

Spectra^®Dome Drives

3500 Pelco Way,

Clovis, CA 93612-5699

USA

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

In North America & Canada:

Tel (800) 289-9100

FAX (800) 289-9150

1. Installation and servicing should only be done by qualified service personnel and conform

to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure,

it is designed for indoor use only and it must not be installed where exposed to rain and

moisture.

International Customers:

Tel +1 (559) 292-1981

FAX +1 (559) 348-1120

3. Only use replacement parts recommended by Pelco.

www.pelco.com

4. After replacement/repair of this unit’s electrical components, conduct a resistance measure-

ment between line and exposed parts to verify the exposed parts have not been connected

to line circuitry.

5. The installation method and materials should be capable of supporting four times the

weight of the enclosure, pan/tilt, camera and lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present

within this unit.

C A U T I O N :

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there are impor-

tant operating and maintenance instructions

in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and

operation.

MEASURES DE SECURITE IMPORTANTES

Avant d’installer ou d’utiliser ce produit, les mesures de sécurité suivantes sont à prendre:

1. Toute installation et réparation devraient être entreprises par un technicien qualifié et

conformes au codes locaux.

2. A moins que cet equipement indique avoir un boitié agrée NEMA de type 3, 3R, 3S, 4, 4X,

6 ou 6P, il est uniquement conçu pour utilisation intérieure et ne peut donc pas être en con-

tact de pluie ou d’humidité.

3. Utiliser seulement les pièces de rechanges recommandées par Pelco.

4. Après toute installation ou réparation de la partie électrique de ce produit, une résistance

entre le courant et la partie exposée devrait être installée afin de vérifier que la partie

électrique n’aie pas été en contact d’un court circuit.

5. L’installation entreprise et le matériel utilisé devraient supporter quatre fois le poids du

boitié, de la tourelle, de la caméra, et de la lentille.

Ce produit et/ou le manuel pourrait inclurent les symbols suivants:

Ce symbol indique qu’un voltage dangereux

pouvant provoquer un chock électrique est

présant dans cette unité.

CAUTION:

RISQUE DE CHOQUE ÉLECTRIQUE.

Ce symbol indique qu’il y a des mesures

NE PAS OUVRIR.

d’installation et d’entretient importantes inclus

dans le manuel de cet équipement.

Nous vous prions de bien vous familiarisez avec la manuel avant d’entreprendre toute installation.

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Step 1 - Turn on power to the back box.

The red LED will light. IMPORTANT: If the LED does not light, refer to the Troubleshooting section.

Step 2 - Prepare the dome drive for installation.

a. Set the DIP switches for SW1 and SW2 on the bottom of the dome drive for the appropriate

receiver address. Refer to the labels on the dome drive or Tables A through C.

b. Daisy Chain Operation Only – When connecting more than one Spectra dome system to a

single controller, terminate the last unit in the chain (farthest from the controller). To termi-

nate the dome drive set the RS-422 termination switch to the left.

SW1

SW2

LABEL

SW1

SW2

LABEL

SW2

RS-422 TERMINATION SWITCH

00303

Step 3 - Install the dome drive into the back box.

Line up the green and red tabs with the green and red labels. Push in on the tabs. Insert the side

with the green tab, then the side with red tab. Continue pushing on the ends of the tabs until

both sides click into place.

RED

TAB

GREEN

TAB

CAUTION: Make sure the dome drive locks into place. Pull down on the dome drive with

moderate pressure to ensure that it stays in place.

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Switch Settings for SW1

Control Type

Switch Setting

SW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8

Coaxitron

P-Type Control

D-Type Control

OFF

OFF*

OFF**

NOTES: Switches SW1-3 through SW1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500 and CM8500

controllers or with American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco's CM6700/CM9750/CM9760 control

systems.

* OFF - Use with controllers that have more than 32 presets.

ON - Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

Table B. Switch Settings for SW2 – P-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF.

For D-type control systems, refer to Table C.

Receiver Address

Switch Setting

SW2-3

SW2-1

SW2-2

SW2-4

SW2-5

OFF

Baud Rate

Switch Setting

SW2-6

SW2-7

SW2-8

2400

4800

9600

OFF

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For P-type control systems, refer to Table B.

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

OFF

(Continued on next page)

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Switch Settings for SW2 – D-Type Control (Continued)

Receiver

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

Receiver

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

Address

129

Address

193

OFF

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

For operating instructions, refer to the SD5 Series Operation and Programming Manual for your

system. Refer to the table below.

Operation and Programming

Model

Manual Number

DD5AM, DD5AM-X, DD5BC22,

C2419M-A

DD5BC22-X, DD5BC, DD5BC-X

DD5BCBW, DD5BCBW-X

DD5TAC, DD5TAC-X

C2423M

C2422M

If you do not have the operation and programming manual for your system, obtain a manual by

doing one of the following:

•

Go to Pelco’s web site at ftp://www.pelco.com and find the manual number (refer to the

table above).

Contact Pelco’s Literature Department and request a manual (refer to the table above).

TROUBLESHOOTING

Problem

Possible Cause

Solution

Unit does not

operate. The

controller is

not communi-

cating with

the Spectra

unit.

Check to see if the red

LED on the circuit board in

the back box is lit.

1. The red LED is not

lit.

a. Fuse is bad.

a. Check fuse on the circuit board. Re-

place fuse if it is bad. To order a fuse

from Pelco, specify the part number

FUS1.6-5X20FAST. This is a 1.6-

ampere fuse, 5 x 20 mm, fast blow.

b. 24 VAC power

source is not

connected or is

bad.

b. Return the back box to the factory

for repair.

2. The red LED is lit.

a. Wiring is incor-

rect or is not

a. Check all connections to the circuit

board. Make sure that all connec-

tions are fully seated and the board

is wired correctly.

fully seated.

b. DIP switch

settings are

incorrect.

b. Check the DIP switch settings on

the dome drive (refer to Tables A,

B, and C). If the unit still does not

operate, turn off power and replace

the dome drive with a good unit, if

you have a spare. Check the

switch settings on the substitute

dome drive before installing it. (If

you do not have a spare, return the

dome drive and back box to the

factory.) If you substituted a dome

drive and the unit operates, the

original dome drive is bad (return

the dome drive to the factory). If the

unit still does not operate,

then the circuit board is bad (return

the back box to the factory).

Fan does not

operate.

Fan connections are not

fully seated.

Make sure the connector for the fan is

fully seated. If the fan still does not

operate, return the back box and dome

drive to the factory for repair.

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

REGULATORY NOTICES

•

Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician

for help.

Class B meets more stringent requirements than Class A.

The following applies to NTSC/EIA models DD5AM, DD5BC,

and DD5TAC.

The following applies to NTSC model DD5BC22.

This equipment has been tested and found to comply with the

limits of a Class B digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the in-

structions, may cause harmful interference to radio communica-

tions. However there is no guarantee that the interference will not

occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is

encouraged to try and correct the interference by one or more of

the following measures:

This equipment has been tested and found to comply with the

limits of a Class A digital device, pursuant to part 15 of the FCC

rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and

can radiate radio frequency energy and, if not installed and used

in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equip-

ment in a residential area is likely to cause harmful interference

in which case the user will be required to correct the interference

at his own expense.

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the

receiver.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

Exceptions to this warranty are as noted below:

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FT/FR8000 Series ﬁber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Three years on Camclosure^®and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

•

Two years on standard motorized or ﬁxed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual # Date

Comments

C1489M

7/98

9/98

11/98

Original version.

Revised Section 5.0, Troubleshooting.

Added material on EIA and CCIR monochrome cameras, and PAL color camera. Changed certifications. Revised material in

Section 4.11.21.2 (Programming Limit Stops). Changed the fixed-speed controller rate in Section 7.0.

Revised the certifications table in Section 2.2. Revised the sensitivity ratings under Camera in Section 7.0, Specifications.

Revised the preset tilt speed from 100 to 200 degrees/second. Added a note relating to running patterns when an alarm

activates. Revised Troubleshooting section. Revised manual to new format.

Added Spectra Lite material. Replaced the standard Spectra II DD5AC and DD5AC-X cameras with model DD5BC and

DD5BC-X cameras. Added optional 176X color models. Removed operation instructions and specification section.

Revised Installation, Operation and Troubleshooting sections.

2/99

7/99

C1489M-A

C1489M-B

9/99

C1489M-C

C1489M-D

C1489M-E

3/00

5/00

01/01

Revised Description and added color/black and white camera models.

Added step to dome drive installation instructions referencing the new RS-422 termination switch.

® Pelco, the Pelco logo, Spectra, Genex, Legacy, PelcoVision and Coaxitron are registered trademarks of Pelco.

™ Esprit, Camclosure, and LowLight are trademarks of Pelco.

Pelco Manual C1489M-E (01/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Peerless Industries Car Video System PA740 User Manual
Philips Refrigerator SA1340 User Manual
Philips TV Cables SWA2553 User Manual
Philips VCR VR122 User Manual
Philips Work Light 12821ECO User Manual
Pioneer DVD Player DVR 320 S User Manual
Pioneer TV DVD Combo V5000 User Manual
Polaroid Digital Camera i639 User Manual
Powerware Power Supply 650825 kVA User Manual
Premier Mounts TV Mount 9533 004 001 07 User Manual