SETUP MENUS
ACCESSING THE SETUP MENUS
C2947M-D (6/08)
C10CH Series Camera
Quick Start Guide
Use the 5-position button controller on the side panel of the camera to access and navigate the on-screen
display (OSD) menus. Use the following table to navigate through the menu options.
The camera default settings are set at the factory to operate in most applications and lighting conditions,
and normally require no adjustments. Sometimes, however, adjustments may be necessary.
Use the setup menus to customize the camera settings for your application as needed. Refer to the
Installation/Operation manual (C2946M) for complete instructions and explanations of camera settings.
Menu Options
Navigating the Menu
Press and hold down the center button for two
seconds.
Display the MAIN MENU on the screen.
This quick start guide describes how to install and configure the C10CH Series camera in most
applications. It contains a representation of the setup menus to help you locate and change specific
settings.
PROFILES
Move the cursor up or down in a menu or toggle
through menu selections.
STANDARD
GAMING
CUSTOM
Move the button up or down.
BACK
EXIT
Refer to the enclosed CD for the following documentation:
MAIN MENU
Move the cursor right or left in a menu.
Select a menu or make a menu selection.
Save a setting and then return to the menu.
Move the button left or right.
Press the center button.
Press the center button.
PROFILES
->
->
->
•
•
•
Installation/Operation manual: C2946M
Quick Start Guide: C2947M
Important Safety Instructions: SAFETY.PDF
EXPOSURE SET.
FUNCTION SET.
SAVE AS CUSTOM
->
->
->
PIXEL CORRECTION
SYSTEM INFORMATION
EXPOSURE SET.
ECLIPSER
AUTO EXPOSURE
ECLIPSER
DC IRIS LEVEL
FLICKERLESS
AGC
-> ESC
-> OFF
-> -8
ECLIPSER
THRESHOLD
LEVEL
-> OFF
-> 17
-> 4
EXIT
LENS
-> OFF
-> LOW
BACK
EXIT
MODELS
BACK
EXIT
The C10CH Series camera supports both manual and auto iris lenses, either fixed focal length or
varifocal. It automatically senses an auto iris lens as soon as you plug in the connector.
C10CH-6
1/3-inch ultra high resolution color, CCD camera, 24 VAC or 12 VDC, NTSC format
The camera has a standard CS mount that can accept a C mount lens with a PCMA40 lens adapter.
To mount the lens onto the camera:
C10CH-6X 1/3-inch ultra high resolution color, CCD camera, 24 VAC or 12 VDC, PAL format
C10CH-7X 1/3-inch ultra high resolution color, CCD camera, 220 to 240 VAC, PAL format
1. Make sure the lens does not touch the camera imager when installed.
FUNCTION SET.
LINE SYNC
C10CH-7X BACK
LINE SYNC
-> AUTO
-> AUTO
->
LINE SYNC
-> AUTO
-> 38
2. Use clean, compressed air or a clean, dry lens cloth to make sure there is no dust or other foreign
matter between the lens and the camera imager.
WHITE BALANCE
CHROMA
V-PHASE ADJ
GAMMA
-> 60%
-> SHARP
-> SHORT
->
BACK
EXIT
SHARPNESS
CABLE COMPENSATION
MASKING
3. C mount lens: Screw the adapter onto the lens.
TITLE
->
4. Screw the lens onto the lens mount.
MASKING
BACK
EXIT
MASK
-> OFF
-> -2
-> 0
5. Auto iris lens: Connect the 4-pin connector from the lens to the connector on the side of the
MASK COLOR
MASK EDIT
MASK ERASE
camera.
SAVE AS CUSTOM
BACK
EXIT
CURRENT SETTING
ARE SAVED
OK
CANCEL
TITLE
TITLE
EDIT TITLE
-> OFF
PIXEL CORRECTION
ì Camera Mount
r Ground Screw
BACK
EXIT
COVER THE LENS
AND PRESS OK
î Back Focus Locking Screw
ï Lens Mount
s Power Connector
OK
CANCEL
•
•
C10CH-6/6X, Power Terminal Block
C10CH-7X, Power Cord
ñ Auto Iris Lens Connector
ó Setup Button
t Video Output Connector
SYSTEM INFORMATION
RESTORE FACTORY SETTING
FIRMWARE VERSION
OSD VERSION
#.##
#.##
ALL SETTING ARE
INITIALIZED
RESTORE FACTORY SETTINGS ->
OK CANCEL
RETURN
END
Download from Www.Somanuals.com. All Manuals Search And Download.
|