Pelco Saw C2434M User Manual

CC5BCBW Series

Heavy-Duty Spectra^®

Back Box

Installation Manual

C2434M (7/01)

Pelco • 3500 Pelco Way, Clovis • CA 93612-5699 USA • www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150

International Customers: Tel +1 (559) 292-1981 or FAX +1 (559) 348-1120

Download from Www.Somanuals.com. All Manuals Search And Download.

DESCRIPTION

The Heavy-Duty Spectra is perfect for installations where structural integrity and vandalism

are a priority. The system features heavy-duty construction and tamper-resistant barrel key

locks. The in-ceiling model has a reinforced bracket mounting system for installation in a

fixed ceiling. Pendant models can be mounted to a pole, corner or directly to a wall.

SYSTEM MODELS

CC5BCBW-HF1

Heavy-duty, in-ceiling back box; standard clear dome; and color/black

and white camera.

CC5BCBW-HBF1 Heavy-duty, in-ceiling back box; heavy-duty clear dome; and color/

black and white camera.

CC5BCBW-HP1

Pendant style back box, standard clear dome, and color/black and

white camera.

CC5BCBW-HBP1 Pendant style back box, heavy-duty clear dome, and color/black and

white camera.

Each heavy-duty lower dome is designed for a specific back box model. Install the correct

lower dome to the right back box. See the following chart.

System Model

CC5BCBW-HF1

CC5BCBW-HBF1

CC5BCBW-HP1

CC5BCBW-HBP1

Back Box

Lower Dome

Dome Drive

DD5BCBW

BB5HD-F

CLCLD5HDF-1

CLCLD5HDBF-1

CLCLD5HDPG-1

LD5HDPG-1

BB5HD-F

CLCBB5HD-PG

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION OF IN-CEILING MODEL

STEP 1 - PREPARE CEILING

00530

00532

00531

a. Locate the center point of the mount-

ing location. Drill a hole in the ceiling

using a 3/32-inch drill.

b. Insert the compass tool into the hole.

c. Use the mounting ring as a template

and mark the hole pattern onto the

mounting surface. Prepare the holes.

Draw a circle on the ceiling using the

compass tool and a pencil. Cut the

circle out of the ceiling.

STEP 2 - INSTALL THE MOUNTING PLATES

Use the eight 10-32 x 3-inch screws (supplied) and install the mounting ring and

two back mounting plates.

CEILING

a. Line up the mounting ring with the eight

fastener holes.

c. Install fasteners through the mounting

ring, ceiling and out the back mounting

plate.

b. Feed one back mounting plate through

the hole in the ceiling and line up with

four fastener holes.

MOUNTING

RING

d. Install second back mounting plate.

00533

STEP 3 - INSTALL THE BACK BOX

SPRING CLIP

ATTACH SAFETY CHAIN HERE

8-32X.275 INCH SCREW

00534

00535

00537

a. Attach the conduit fitting, lock nut, and

safety chain bracket. Install a safety

chain/cable (not supplied) that will

support up to 16 pounds (7.3 kg).

b. Turn the thumbscrew and open the

hinged door to the back box.Pull wiring

into the back box through the conduit

fitting. Refer to Tables A and B in the

Appendix for wiring distances.

c. Compress the spring clips on the back

box and push it through the hole until

the clips spring back.Tighten the screws

until you hear a clicking noise. Insert the

two 8-32 x .275-inch screws to secure

the back box to the mounting ring.

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 4 - WIRE CIRCUIT BOARD

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

Attach the wiring to the circuit board inside the back box. When

finished, close the door to the back box and turn on the power.

The red LED will light.

CONTROLLER

VIDEO IN

COAXITRON

CONTROLLER

VIDEO OUT

IMPORTANT: If the LED does not light, refer to the Trouble-

shooting section.

2 WIRE

CONTROLLER

TX-

TX+

RX-

RX+ CONTROL

TX-

NOT USED

(RS-422)

TX+

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

ALARM

INPUTS

SPECTRA II ONLY

GROUND

(NO)

(NC)

SWITCHES

(WIRING EXAMPLE)

+5 VDC

+5 to +24 VDC

RELAY

(AUX 1)

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

GROUND

HEATER/FAN (NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

00542

STEP 5 - INSTALL DOME DRIVE

SW1

SW2

RED

TAB

GREEN

TAB

LABEL

SW1

SW2

LAB

SW2

RS-422 TERMINATION SWITCH

00539

00538

a. Set the DIP switches for SW1 and SW2 on the bottom of the

dome drive for the appropriate receiver address. Refer to the

labels on the dome drive orTables C through E in the Appendix

in the back of this manual.

b. Line up the green and red tabs with the green and red labels.

Push in on the tabs. Insert the side with the green tab, then the

side with red tab. Continue pushing on the ends of the tabs

until both sides click into place.

STEP 6 - INSTALL LOWER DOME

a. Attach the lower dome trim leash to one of the 8-32 x .275-

inch screws that secure the back box to the mounting ring.

b. Insert both keys in the barrel locks. Turn keys clockwise to the

unlocked position. Keys can not be removed from lock in the

unlocked position.

BALL STUD

RECEIVER

c. Align pegs (located on the mount ring) with the peg recep-

tacles (located on the inside of the lower dome).

TRIM LEASH

d. Place lower dome over back box. Hold and turn both keys to

the locked position.

TO USE YOUR DOME, REFER TO THE OPERATION AND

PROGRAMMING MANUAL.

BARREL

KEY LOCK

00497

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION OF PENDANT MODELS

STEP 1 - DISASSEMBLE BACK BOX

01082

01081

a. Turn the thumbscrew and open the hinged door located

inside the back box.

Unscrew the three Phillips screws located underneath the

hinged door. Remove the inside portion of the back box.

01080

Remove the inside mounting plate by loosening the three

Phillips screws.

STEP 2 - PREPARE INSTALLATION AREA

NOTE: If installing outdoors make sure the installation is properly sealed to keep moisture out.

Prepare cable and wiring for the system. Refer to Tables A and B in the Appendix for wiring distances.

There are three different methods of installation:

1. Direct Mounting to a Wall – Use the mounting side of the octagonal back box as a template and mark the three fastener holes

and conduit hole onto the mounting surface. Set the back box to the side and prepare the holes for the installation.

2. Corner Mounting – Refer to the instructions supplied with the CLCCM corner mount.

3. Pole Mounting – Refer to the instructions supplied with the CLCPA pole adapter.

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 3 - INSTALL THE BACK BOX

01078

01079

a. Secure the conduit fitting to the hole located on the inside

base of the octagonal back box.

Thread the cable/wiring through the back box mounting

plate. Attach the plate to the mounting base using the

screws previously removed. Pull cable/wiring into the

inside back box (the back box hinged door should be

opened). Attach the inside back box to the mounting plate.

Use the three Phillips head screws previously removed.

b. Pull the cable and wiring for the system through the

octagonal back box and conduit fitting. Mount the back

box to the mounting surface, corner, or pole mount.

STEP 4 - WIRE CIRCUIT BOARD

Attach the wiring to the interconnect circuit board inside

the back box. Close the door to the back box. Turn on

power to the back box. The red LED will light.

24 VAC

TRANFORMER

POWER

(24 VAC ONLY)

CONTROLLER

VIDEO IN

COAXITRON

CONTROLLER

VIDEO OUT

IMPORTANT: If the LED does not light, refer to the

Troubleshooting section.

2 WIRE

CONTROLLER

TX-

TX+

RX-

RX+ CONTROL

NOT USED

(RS-422)

TX-

TX+

NOTE: Aux 1 - Maximum 2A at low voltage (<40V)

Aux 2 - Maximum 150 vA at 32 VDC

ALARM

INPUTS

SPECTRA II ONLY

GROUND

(NO)

(NC)

SWITCHES

(WIRING EXAMPLE)

+5 VDC

+5 to +24 VDC

RELAY

(AUX 1)

LOGIC GATE

(WIRING EXAMPLE)

AUX 2

GROUND

HEATER/FAN (NOT USED)

AUX 2

EXTERNAL RELAY

(WIRING EXAMPLE)

00542

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

STEP 5 - INSTALL DOME DRIVE

SW1

SW2

LABEL

SW1

SW2

LAB

SW2

RS-422 TERMINATION SWITCH

00538

a. Set the DIP switches for SW1 and SW2 on the bottom of

the dome drive for the appropriate receiver address. Refer

to the labels on the dome drive or Tables C through E in

the Appendix in the back of this manual.

01083

b. Daisy Chain Operation Only – When connecting more

than one Spectra dome system to a single controller,

terminate the last unit in the chain (farthest from the

controller). To terminate the dome drive set the RS-422

termination switch to the left.

Line up the green and red tabs with the green and red

labels. Push in on the tabs. Insert the side with the green

tab, and then the side with red tab. Continue pushing on

the ends of the tabs until both sides click into place.

STEP 6 - INSTALL LOWER DOME

BARREL

LOCK

TRIM

LEASH

O-RING

00543

01084

a. Lightly apply O-ring lubricant to the O-ring. Install the

O-ring in the groove on the trim ring of the lower dome.

Attach the back box trim leash to a retainer screw inside

the lower dome.

Align barrel locks in lower dome with the holes located on

each side of the back box. Push lower dome onto back

box. Press the pins of the barrel locks IN to secure the

lower dome.

Environmental Model only – Plug the two-pin heater connection

in the lower dome into the mating connector in the back box.

TO USE YOUR DOME, REFER TO THE OPERATION AND

PROGRAMMING MANUAL.

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

PROBLEM

POSSIBLE CAUSE

SOLUTION

Unit does not operate.

The controller is not

communicating with

the Spectra unit.

Check to see if the red LED on the circuit

board in the back box is lit.

1. The red LED is not lit.

a. Fuse is bad.

a. Check fuse on the circuit board. Replace fuse if it is

bad. To order a fuse from Pelco, specify the part

number FUS1.6-5X20FAST. This is a 1.6-ampere

fuse, 5 x 20 mm, fast blow.

b. 24 VAC power source is not con-

nected or back box is bad.

b. Use a voltmeter to check if 24 VAC is getting to the

power connector on the circuit board. If NO, check

your power supply. If YES, return the back box to

the factory for repair.

2. The red LED is lit.

a. Wiring is incorrect or is not fully

seated.

a. Check all connections to the circuit board.

Make sure that all connections are fully seated and

the board is wired correctly.

b. DIP switch settings are incorrect.

b. Check the DIP switch settings on the dome drive

(refer to Tables C, D, and E). If the unit still does

not operate, turn off power and replace the dome

drive with a good unit, if you have a spare. Check

the switch settings on the substitute dome drive

before installing it. (If you do not have a spare,

return the dome drive and back box to the factory.)

If you substituted a dome drive and the unit

operates, the original dome drive is bad (return

the dome drive to the factory). If the unit still

does not operate, then the circuit board is bad

(return the back box to the factory).

Fan does not

operate.

Fan connections are not fully seated.

Cameras are out of phase.

Make sure the connector for the fan is fully seated. If

the fan still does not operate, return the back box and

dome drive to the factory for repair.

Vertical roll on monitor

when switching

between cameras.

If you are wiring more than one dome to the same

transformer, it is important to wire the power connec-

tor in each dome the same way. That is, the wiring

from one side of the transformer must be connected

to the same connector on each dome.

DOME 1

POWER

WARNING: Make

sure you wire power

to the outer connec-

tors of the terminal

block and ground to

the middle connec-

tor. Otherwise, you

DOME 2

POWER

could damage the

DOME 3

POWER

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Table A. Video Coaxial Cable Requirements

Cable Type*

Maximum Distance

RG59/U

RG6/U

RG11/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance. All-copper center conductor.

95% braided copper shield.

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC with a 10-

percent voltage drop. (Ten percent is generally the maximum allowable voltage

drop for AC-powered devices.)

Wire Gauge

30 vA

75 vA

94 ft

(28 m)

150 ft

(45 m

238 ft

(115 m)

380 ft

(72 m)

603 ft

(183 m)

960 ft

(292 m)

37 ft

60 ft

95 ft

152 ft

241 ft

384 ft

(11 m)

(18 m)

(29 m)

(46 m)

(73 m)

(117 m)

NOTE: Input power for the dome is 24 VAC only. Power consumption is 30 vA

per dome for indoor models and 75 vA for outdoor models.

Use a 24 VAC transformer with the following minimum vA:

40 vA per dome

100 vA per dome

For indoor models (without heater)

For outdoor models (with heater)

Table C. Switch Settings for SW1

Control Type

Switch Setting

SW1-1

OFF

SW1-2

OFF

SW1-3

SW1-4

OFF

SW1-5

OFF

SW1-6

OFF

SW1-7

OFF

SW1-8

OFF**

Coaxitron^®

OFF

P-Type Control

D-Type Control

OFF

OFF*

NOTES: Switches SW 1-3 through SW 1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500, CM8500, and Genex^®controllers or with

American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco’s CM6700/CM9750/CM9760 and Genex control systems.

OFF- Use with controllers that have more than 32 presets.

ON- Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table D. Switch Settings for SW2 – P-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For D-type control systems, refer to Table E.

Receiver

Address

Switch Setting

SW2-3

Receiver

Address

Switch Setting

SW2-3

SW2-1

SW2-2

SW2-4

SW2-5

SW2-1

SW2-2

SW2-4

SW2-5

OFF

Baud Rate

Switch Setting

SW2-6

SW2-7

SW2-8

2400

4800

9600

OFF

Table E. Switch Settings for SW2 – D-Type Control

NOTE: For Coaxitron controls, SW2 is not used; set all switches OFF. For P-type control systems, refer to Table D.

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

(Continued on next page)

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

OFF

100

101

102

103

104

OFF

(Continued on next page)

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver

Address

Switch Setting

Receiver

Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

OFF

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

MECHANICAL

Construction

Back box:

Dome drive:

Lower dome:

Cable Entry

In-Ceiling:

Pendant:

Pan Movement:

Vertical Tilt:

Manual Pan/Tilt Speeds*

Pan:

Aluminum

Aluminum, ABS plastic

Acrylic

.75-inch (1.91 cm) conduit fitting

Through 1.5-inch (3.81 cm) NPT pendant mount

360° continuous pan rotation

Unobstructed +2° to -92°

0.1-80° /sec manual operation, 150° /sec turbo

Tilt:

0.1-40° /sec

Preset Speeds

Pan:

250° /sec

Tilt:

200° /sec

* For variable-speed operation an appropriate controller is required. With fixed-speed

controllers, pan/tilt speed is 24°/sec. The CM6700 controller with the KBD200 keyboard

has programmable fixed speeds.

ELECTRICAL

Input Voltage:

Input Power:

18-30 VAC, 24 VAC nominal

30 vA nominal (indoor, w/o heater)

75 vA nominal (outdoor, with heater)

1.6 A

Fuse:

Relay Contacts

Type:

Voltage:

Current:

AUX 1

Form C

Low voltage (<40 V)

2 A maximum

AUX 2 Output

Open collector transistor output

32 VDC maximum

150 mA maximum

CAMERA

Signal Format:

Scanning System:

Image Sensor:

Effective Pixels:

Horizontal Resolution:

Lens Minimum f-stop:

Focal Length:

NTSC (model DD5BCBW)

2:1 interlace

1/4-inch interline transfer CCD

768 (H) x 494 (V)

>470 TV lines

F1.4

4.1 mm to 73.8 mm optical

18X optical zoom, 4X electronic zoom

Auto/manual speed selection

Zoom Ratio:

Digital Slow Shutter:

Horizontal Angle of View: 48° (at 4.1 mm wide zoom), 2.7° (at 73.8 mm telephoto zoom)

MTBF:

Focus:

>500,000 cycles at room temperature (zoom, focus, irs)

Automatic and manual override

Sensitivity: .

2 lux at 1/4-second shutter speed (color)

.2 lux at 1/60-second shutter speed (black & white)

AC line lock, phase adjustable via remote control*

Automatic with manual override*

Speed Automatic (electronic iris)/manual

1/4 to 1/10,000*

Sync System:

White Balance:

Shutter:

Iris Control:

Gain Control:

Video Output:

Signal to Noise Ratio:

Automatic with manual override*

714V ± .07V (100 IRE ± 10 IRE)

>46 dB

* Manual control of camera setup functions can be done with CM6700, CM6800, CM8500,

CM9500, CM9740, CM9760 and MPT9500 controllers, but not with CM7500, MPT9000

or KBD9000 controllers.

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL

Environment

In-Ceiling:

Indoor only

Pendant:

Indoor/outdoor

Operating Range

In-Ceiling:

32 to 122°F (0 to 50°C)

Pendant:

(Assumes no wind chill factor; for detailed test conditions,

contact Pelco)

Maximum:

140°F (60°C) absolute maximum

122°F (50°C) sustained maximum

-15°F (-9.4°C) absolute minimum

See Figure 1

Minimum

Dimensions:

Weight Unit

Back Box and Lower Dome

In-ceiling:

3 lb (1.36kg)

Pendant:

Dome Drive:

7 lb (3.17 kg)

2.65 lb (1.20 kg)

(Design and product specifications subject to change without notice.)

10.25

(26.03)

10.37

(33.95)

6.8

(17.27)

ﬂ6.13

(ﬂ15.57)

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS;

ALL OTHERS ARE INCHES

Figure 1. Dimension Diagram

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment.

warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or

(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following

information:

1. Model and serial number

Exceptions to this warranty are as noted below:

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on FT/FR8000 Series ﬁber optic products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the

warranty conditions stated above, please include a written explanation with the product

when returned.

Three years on Camclosure^®and ﬁxed camera models, except the CC3701H-2,

CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,

which have a ﬁve-year warranty.

Method of return shipment shall be the same or equal to the method by which the item was

received by Pelco.

•

Two years on standard motorized or ﬁxed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series

ﬁxed dome products.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at

(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned

for credit, and RA number if returned for repair).

•

Two years on Spectra^®, Esprit^®, ExSite^™, and PS20 scanners, including when used in

continuous motion applications.

•

Two years on Esprit^®and WW5700 Series window wiper (excluding wiper blades).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing

charge.

Eighteen months on DX Series digital video recorders, NVR300 Series network video

recorders, and Endura^™Series distributed network-based video products.

Goods returned for repair or credit should be clearly identiﬁed with the assigned CA or RA

number and freight should be prepaid. Ship to the appropriate address below.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be

covered for a period of six months.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Six months on all pan and tilts, scanners or preset lenses used in continuous motion

applications (that is, preset scan, tour and auto scan modes).

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco

shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,

California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident

are not covered under this warranty.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are

instructed to return goods to the USA, you may do one of the following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from

the speciﬁc use or application made of the Products. Pelco’s liability for any claim, whether

based on breach of contract, negligence, infringement of any rights of any party or product

liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for

such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of proﬁt and claims of third parties) however caused,

whether by the negligence of Pelco or otherwise.

Pelco

3500 Pelco Way

Clovis, CA 93612-5699 USA

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco c/o Expeditors

473 Eccles Avenue

The above warranty provides the Dealer with speciﬁc legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual #

Date

Comments

C2434M

7/01

Original version.

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.

Endura and ExSite are trademarks of Pelco.

Pelco Manual C2434M (7/01)

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Music Mixer XXRR 880000FF++ User Manual
Philips Flat Panel Television 15PF5120 28B User Manual
Philips Headphones SWB9000 27 User Manual
Philips Indoor Furnishings WP3861 User Manual
Philips Telephone 380 Duo Vox User Manual
Pioneer MiniDisc Player MJ L11 User Manual
Pioneer Portable Speaker S 1EX User Manual
Porter Cable Laser Level LR1100 User Manual
Poulan Trimmer PE225 User Manual
Psiber Data Systems Network Card PINGER User Manual