Pelco Printer cm6800 322x6 User Manual

I N S T A L L A T I O N / O P E R A T I O N

CM6800-32X6

Matrix Switcher

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION ........................................................................................................................................................................................................................ 55

OVERVIEW ................................................................................................................................................................................................................ 55

OPERATING THE CM6800......................................................................................................................................................................................... 55

SWITCH MONITORS ....................................................................................................................................................................................... 55

SELECT CAMERAS .......................................................................................................................................................................................... 56

CONTROL RECEIVERS ...................................................................................................................................................................................... 56

OPERATE SEQUENCES..................................................................................................................................................................................... 57

RUN A MACRO ................................................................................................................................................................................................ 58

ACKNOWLEDGE AN ALARM .......................................................................................................................................................................... 58

CALL A PRESET ................................................................................................................................................................................................ 59

CREATE AND RUN A PATTERN ....................................................................................................................................................................... 59

OPERATE AUXILIARIES/RELAYS ...................................................................................................................................................................... 60

CONTROL GENEX MULTIPLEXER AND GENEX MULTIPLEXER DISPLAYS....................................................................................................... 61

OPERATE SCANNING FUNCTIONS ................................................................................................................................................................. 61

DETECT VIDEO LOSS ....................................................................................................................................................................................... 61

DEFINE ZONES ................................................................................................................................................................................................ 61

APPENDIX .......................................................................................................................................................................................................................... 62

CM6800 DIP SWITCHES ........................................................................................................................................................................................... 62

ALARM GROUP DISPLAY OPTIONS ................................................................................................................................................................. 63

MACRO COMMANDS .............................................................................................................................................................................................. 65

ASCII OPERATING COMMANDS .............................................................................................................................................................................. 67

TROUBLESHOOTING ................................................................................................................................................................................................. 70

GAINING INITIAL CONTROL ............................................................................................................................................................................ 70

SOFTWARE RESET ........................................................................................................................................................................................... 70

SOLUTIONS TO COMMON PROBLEMS .......................................................................................................................................................... 71

KBD960/KBR960 ICON/BUTTON LEGEND ............................................................................................................................................................... 72

GLOSSARY ......................................................................................................................................................................................................................... 73

INDEX ................................................................................................................................................................................................................................ 76

SPECIFICATIONS ................................................................................................................................................................................................................ 78

REGULATORY NOTICES ..................................................................................................................................................................................................... 79

WARRANTY AND RETURN INFORMATION ...................................................................................................................................................................... 79

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIST OF ILLUSTRATIONS

Figure

Page

Sample CM6800-32X6 System ........................................................................................................................................................................ 7

Installing Rack Ears ......................................................................................................................................................................................... 11

Mounting the CM6800 Matrix Switcher/Controller ....................................................................................................................................... 11

CM6800-32X6 Video Inputs............................................................................................................................................................................. 12

Connecting Terminated Video Sources ........................................................................................................................................................... 13

Connecting Looping Video Sources ................................................................................................................................................................. 13

PTZ Control Connections ................................................................................................................................................................................. 14

Connecting Monitors ....................................................................................................................................................................................... 15

Connecting Alarms .......................................................................................................................................................................................... 16

Communication Port Inputs ............................................................................................................................................................................. 17

CM6800-32X6 Communication Port Connections and Options ...................................................................................................................... 18

Data Cable Plugged into Local Keyboard ........................................................................................................................................................ 19

Data Cable Plugged into COM 5 ..................................................................................................................................................................... 19

Remote Keyboards .......................................................................................................................................................................................... 21

RJ-45 Cable Types ........................................................................................................................................................................................... 22

Connecting a KBD960/KBR960 to the CM6800-32X6 ..................................................................................................................................... 23

Connecting a Single ALM2064 Alarm Interface Unit ...................................................................................................................................... 24

Connecting a Single REL2064 Relay Interface Unit ........................................................................................................................................ 24

Connecting Multiple M Devices – Local Connection ...................................................................................................................................... 25

Connecting Multiple M Devices – Remote Connection .................................................................................................................................. 26

PC Connection to DB9 Port .............................................................................................................................................................................. 27

Connecting Genex Multiplexers ...................................................................................................................................................................... 28

Wiring the AUX 1 (Relay) Output .................................................................................................................................................................... 29

Wiring the F2 (TTL) Output .............................................................................................................................................................................. 30

CM6800 Time/Date Stamp on Monitor ........................................................................................................................................................... 31

CM6800 Color Bars ......................................................................................................................................................................................... 33

CM6800 Password Screen .............................................................................................................................................................................. 35

CM6800 Programming Main Menu ................................................................................................................................................................. 35

Sample Access Screen .................................................................................................................................................................................... 38

Program Alarm Groups .................................................................................................................................................................................... 39

Program an Internal or External Alarm Screen ............................................................................................................................................... 40

Program Video Loss Alarms............................................................................................................................................................................. 41

Program Auxiliary Outputs .............................................................................................................................................................................. 42

Program Logical Camera Numbers .................................................................................................................................................................. 43

Program Cameras ............................................................................................................................................................................................ 44

Sample Event Timer Programming .................................................................................................................................................................. 46

Access the Macro Screen ............................................................................................................................................................................... 47

Macro Status View Screen.............................................................................................................................................................................. 47

Access the Monitor Screen ............................................................................................................................................................................. 48

Access the Set Password Screen .................................................................................................................................................................... 50

Access the Port Screen ................................................................................................................................................................................... 51

Access the Priority Screen .............................................................................................................................................................................. 52

Sequence Screen ............................................................................................................................................................................................. 52

Scratchpad Sequence Screen ......................................................................................................................................................................... 53

Access the Time and Date Screen .................................................................................................................................................................. 54

CM6800 DIP Switches – Factory Default Settings ......................................................................................................................................... 62

Dip Switch Cover Plate .................................................................................................................................................................................... 70

CM6800 DIP Switch 7 ..................................................................................................................................................................................... 70

Icon/Button Legend ......................................................................................................................................................................................... 72

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIST OF TABLES

Table

Page

Video Coaxial Cable Requirements ................................................................................................................................................................. 12

Communication Port Devices and Wiring ....................................................................................................................................................... 17

Default Port Settings ....................................................................................................................................................................................... 18

Keyboard Addresses: KBD100/200A/300A Series Keyboards ....................................................................................................................... 20

Switch Settings – KBD200A/300A Keyboards Only ....................................................................................................................................... 20

CM6800 DIP Switch Settings .......................................................................................................................................................................... 62

Macro Commands ........................................................................................................................................................................................... 65

Examples of ASCII Commands ........................................................................................................................................................................ 67

ASCII Commands ............................................................................................................................................................................................. 68

Solutions To Common Problems ...................................................................................................................................................................... 71

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFEGUARDS AND WARNINGS

1. Read, keep, and follow these instructions.

2. Heed all warnings.

3. There are no user-serviceable parts inside this unit. Only authorized service personnel may open the unit.

4. Installation and servicing should only be done by qualified service personnel and conform to all local codes.

5. WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture if this unit is designed for indoor

use only.

6. Unless this unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6 or 6P enclosure, it is designed for indoor use only and it

must not be installed where exposed to rain or moisture.

7. Do not expose this unit to dripping or splashing. Do not place objects filled with liquids, such as vases, on this unit.

8. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

9. The installation method and materials should be capable of supporting four times the weight of the unit and equipment.

10. Do not install near any heat source.

11. Only use attachments/accessories specified by the manufacturer.

12. Clean only with dry cloth.

13. Do not defeat the safety purpose of the polarized or grounding-type plug.

14. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they

exit from the unit.

15. Unplug this unit during lightning storms or when unused for long periods of time.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage constituting a risk of

electric shock is present within this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

This symbol indicates that there are important operating and mainte-

nance instructions in the literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation and operation.

FOR QUALIFIED SERVICE PERSONNEL ONLY

1. Only use replacement parts recommended by Pelco.

2. After replacement/repair of this unit’s electrical components, conduct a resistance measurement between line and exposed parts to

verify the exposed parts have not been connected to line circuitry.

3. CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Dispose of used

batteries according to the instructions provided by the battery manufacturer.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

DESCRIPTION

Pelco’s CM6800 Matrix Switcher/Controller is a cross-point video matrix switcher. The CM6800-32X6 provides switching and control for

32 video inputs and six monitor outputs from any one of up to 10 keyboards, PCs, and other devices. All 32 video inputs can be used to

control other devices, such as multiplexers, and allow for looping to other devices.

CM9505UPS

ESPRIT^®

KBD960

CC3500H-2

SPECTRA^®

KBD300A

VIDEO TO

SWITCHER

010101

CONTROL

SPECTRA^®

COM

120/230V~

50/60 HZ

25 WATTS

CAMCLOSURE^®

SPOT MAIN

VCR

IN COM OUT

N NH

OCC S

AUX

OUT

ALARMS

110-240V 50/60 Hz

10 11121314 1516

SVHS

GENEX^®MULTIPLEXER

MONITOR

WALL

BLOCK

12V

TRANSFORMER

20005

ALTERNATE COM 4

CONNECTION

KBD100

KBD300A

KBD200A

Figure 1. Sample CM6800-32X6 System

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Programming

The CM6800 features easy programming through on-screen menus or the Windows^®-based CM6800-MGR software package. All

programming is password-protected. Programming menus are provided in English, French, German, Italian, Polish, Portuguese,

Russian, and Spanish.

Keyboards

Up to eight keyboards from the KBD100/200A/300A Series and two keyboards from the KBD960/KBR960 Series can be connected to the

CM6800-32X6. Camera positioning can be programmed and controlled from the KBD200A/300A and KBD960/KBR960 Series keyboards.

Refer to Associated Equipment for keyboard descriptions.

NOTE: You can program the CM6800 with the KBD200A/300A keyboard while in “CM6800 Mode” only (if you use “CM6800 ASCII

Mode,” you can control the CM6800 switcher, but you cannot program it).

Sequences, Macros, Presets, Patterns, and Zones

The CM6800 features the following programmed operations:

A sequence allows operators to see a routine of 72 camera views on any system monitor over and over again. The sequence can be

operated automatically or manually.

A scratchpad sequence allows an operator to run a sequence from an individual monitor without entering the password-protected

programming menus.

A macro is a sequence of commands or steps. When a macro is run, the steps programmed into that macro are performed. Macros can be

operated automatically or manually. Automatic operation can be based on specific times or dates. Macros can also be triggered by alarms.

The following operations are available only with positionable cameras controlled by KBD200A/KBD300A or KBD960/KBR960 keyboards:

A preset allows operators to direct a PTZ (camera positioning system) to move to a predetermined scene on keyboard command or

as a result of an alarm. In addition, a preset can place a descriptive title on the monitor screen. The number of presets available is

determined by the camera positioning system.

With a pattern operators can program a camera positioning system to move around its viewing area in a repeating pattern. The

number and time length of patterns varies with different positioning systems.

A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is associated. When the associated

camera is panned through or remains within this defined zone, the zone label appears on the monitor.

Interface Control

The CM6800 interfaces with the following:

•

Coaxitron^®standard mode (15-bit) and extended mode (32-bit) protocol receivers

Pelco’s D and P protocol receivers (RS-422)

Pelco’s M protocol devices (RS-485)

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

System Access and Priority

The CM6800 provides the following ways to restrict system access:

•

Camera to Monitor: Cameras can be assigned to specific monitors for viewing.

Keyboard to Monitor: Keyboards can be assigned to control specific monitors.

Camera to Keyboard:

Viewing: Keyboards can be assigned view-only access to specific cameras (no PTZ control).

Control: Keyboards can be assigned full access (both PTZ control and viewing) to specific cameras.

The CM6800 provides eight levels of priority control. Each level defines the ability of a keyboard to control a camera positioning system

(KBD200A/KBD300A or KBD960/KBR960 only) and to access programming screens.

Alarm Inputs

Eight internal alarm inputs are provided on the rear panel of the matrix switcher/controller. These internal alarm inputs are programmable

to associate any camera to any input.

Up to two ALM2064 Alarm Interface Units can be connected to the CM6800. Each alarm interface unit can handle up to 64 alarms, for a

total of 128 external alarms.

Auxiliary Outputs

Two internal auxiliary outputs are provided on the back of the CM6800-32X6. One is a relay output, and one is an open collector (TTL)

output. You can also connect up to two REL2064 Relay Interface Units.

Power, Mounting Methods

The CM6800 operates on 120V or 230V, 50/60 Hz. The case mounts in three rack units (5.25 inches or 13.34 cm) of vertical space in a

universal mount, such as a 19-inch (48.26 cm) equipment bay, or to a wall or tabletop.

Continuous Operating Device

The CM6800 is a self-contained video surveillance system designed for continuous duty operation. Once installed, there are no user or

service technician items that require intervention which would require the system to go off-line or have the power turned off under normal

operation. There are two methods for system programming: direct menu control and indirect control, using a Windows^®-based setup

program supplied by Pelco. Both of these methods are noninvasive and do not require the cycling of power in order for storage or

execution of new software settings. The communication ports use standard low voltage interfaces such as RS-232, RS-422 and RS-485,

and all connections and disconnections do not require rebooting or power cycling. Video connections or changes of termination state do

not require rebooting or power cycling.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MODELS

CM6800-32X6

Matrix switcher/controller with 32 video inputs and 6 monitor outputs, NTSC configured 120/230 V, 50/60 Hz,

autoranging

CM6800-32X6-X

Matrix switcher/controller with 32 video inputs and 6 monitor outputs, PAL configured 120/230 V, 50/60 Hz,

autoranging

ASSOCIATED EQUIPMENT

KBD100

Desktop keyboard with full switching and programming capabilities, +12 VDC or 12 V 50/60 Hz

KBD200A

Desktop keyboard with full switching and programming capabilities, plus push-button control of PTZ functions,

+12 VDC or 12V 50/60 Hz

KBD300A

Desktop keyboard with full switching and programming capabilities, plus joystick control of PTZ functions, +12 VDC

or 12 V 50/60 Hz

KBD960

KBD960-X

KBR960

Full-function desktop variable speed keyboard; 120 V, 50/60 Hz

Same as KBD960, PAL configured for 230 V, 50/60 Hz operation

Full-function rack mount variable speed keyboard; 120 V, 50/60 Hz

Same as KBR960, PAL configured for 230 V, 50/60 Hz operation

KBR960-X

KBDKIT

Wiring kit for connecting KBD100, KBD200A, and KBD300A keyboards to remote keyboard port; includes two RJ-45

wall blocks and a transformer to convert 120 V, 60 Hz to 12 V, 60 Hz for keyboard power

KBDKIT-X

Wiring kit for connecting KBD100, KBD200A, and KBD300A keyboards to remote keyboard port; includes two RJ-45

wall blocks and a transformer to convert 230 V, 50 Hz to 12 V, 50 Hz for keyboard power

CM9505UPS

MX4000

Universal Power Supply for KBD960/KBR960 keyboards

Genex Series Multiplexer; available in color or monochrome duplex, and in color or monochrome simplex.

CM9760-CDU-T

Code distribution unit; 16-channel RS-422 transmit only (transmit wire and ground) distributor; primarily used for

connecting up to 16 PTZ receivers in a “star” or “home run” configuration

ALM2064

Alarm interface unit, provides alarm monitoring capabilities for up to 64 alarm inputs, 100-240 V, 50/60 Hz

Relay interface unit, provides 64 relays for operating peripheral equipment, 100-240 V, 50/60 Hz

Master distribution amplifier with time, date, and title, 120 V, 60 Hz

REL2064

CM9760-MDA

COMPATIBLE PRODUCTS

Switchers

PelcoNet Transmission Systems

Video Management Systems

CM9740, CM9760, CM9770, CM9780

NET300 Series, NET350 Series, NET4001A

VMX200, VMX300, VMX300-E

ADDITIONAL RESOURCES

• CM6800-32X6 Quick Start Guide

• CM6800-MGR Installation/Operation Manual

• Pelco Technical Tips available on Pelco.com or from a Technical Support representative (1-800-289-9100)

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

Unpack and inspect all parts carefully. The following parts are supplied:

CM6800 Switcher/Controller

10-32 x .750-inch pan head screws

.500” OD nylon washers

Power cord

6-foot (1.8 m) straight data cables with RJ-45 connectors

6-foot (1.8 m) reversed data cable with RJ-45 connectors

RJ-45 wall block terminals

NOTE: There are no user-serviceable parts inside this unit. Only authorized service personnel may open the unit.

MOUNTING

1. Select a suitable location for the CM6800. It occupies 5.25 inches (13.34 cm) of vertical space, or three rack units (RUs), in a

universal mount. The CM6800 must be within 6 feet (1.8 m) of a suitable electrical outlet.

Follow proper installation practices and leave 1 RU above and below the CM6800 for ventilation.

Do not connect the power until the installation is complete. Refer to the System Start-Up section.

2. The CM6800 is shipped with the rack ears installed at the front. Reposition as needed for your application. If the ears are not

required, remove them.

POSITION BRACKETS FOR

RACK MOUNTING (REAR)

POSITION BRACKETS FOR

UNDER-TABLE MOUNTING

00624

POSITION BRACKETS FOR

RACK MOUNTING (FRONT)

NOTE: EACH CM6800 COMES

WITH 2 RACK EARS

POSITION BRACKETS FOR

FLUSH MOUNTING

(WALL AND TABLE TOP)

Figure 2. Installing Rack Ears

3. Use supplied pan head screws and washers to mount the CM6800 in a standard 19-inch (48.26 cm) equipment rack or wood or sheet

metal screws to mount against a flat surface, according to your installation requirements.

00615

Figure 3. Mounting the CM6800 Matrix Switcher/Controller

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

VIDEO SOURCES

The CM6800-32X6 offers 32 full-function video inputs which support Coaxitron PTZ control and video loss detection. The video inputs can

be used for looping video connections with terminating and unterminating switches on the back panel. They also provide the ability to

view and interface with other devices, such as Genex multiplexers. If control of the device connected to the video input is required,

connect a data cable between the multiplexer and the CM6800. Refer to the Connecting Genex Multiplexers section for instructions on

connecting and controlling video from a multiplexer.

20021

Figure 4. CM6800-32X6 Video Inputs

1. Connect video cables at the appropriate video input BNC receptacles on the back of the CM6800. For best results, use crimp-on

BNCs only. Do not use screw-on BNCs; these typically do not provide adequate ground and signal connections.

Refer to Table A for video coaxial wiring requirements.

Table A. Video Coaxial Cable Requirements

Cable Type*

Maximum Distance

RG59/U

RG6/U

RG11/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance

All-copper center conductor

All-copper braided shield with 95% braid coverage

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. Set the terminating switches according to your system requirements.

Terminating switches are used to terminate or unterminate the video input. The factory default has the switches set in the

terminated (75-ohm) position.

If you are connecting only a camera to an input, leave the switch in the terminated position.

00626

Figure 5. Connecting Terminated Video Sources

If you are looping the input to another device, set the rear panel switch in the unterminated (Hi-Z) position. Terminate at the final

device.

00627

Figure 6. Connecting Looping Video Sources

NOTE: The end point of any video cable run must be terminated in 75 ohms.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL LINES

You cannot connect a Coaxitron camera to the PTZ port. If your video sources are all controlled by Coaxitron, skip this section.

Connect camera control lines to receivers. If any of your video sources are using D or P protocol via RS-422 communications, they will

connect at the PTZ connector on the back of the CM6800-32X6.

NOTE: D and P protocol receivers cannot be mixed on the same communication port but you can use D on one port and P on the other.

Daisy-chaining (going from one receiver to another) is recommended but not always possible. A maximum of 16 receivers can be daisy-

chained from the PTZ port. If more than 16 receivers are required for your system, or if you do not want to daisy-chain the receiver

connections, use the CM9760-CDU-T. You can connect up to two CM9760-CDU-T units to the CM6800-32X6.

NOTE: After completing system installation and power-up, you must configure the CM6800 and the camera/receiver. Refer to the System

Start-Up section.

VIDEO TO

SWITCHER

SHIELDED

TWISTED

PAIR

RECEIVER 16

RECEIVER 2

RECEIVER 1

RS-422

R+

R-

GND

Figure 7. PTZ Control Connections

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MONITORS

The CM6800-32X6 supports six monitors.

1. Install monitors according to the instructions provided with them.

2. Connect the monitor cables at the appropriate video output BNC receptacles on the back of the CM6800.

3. Terminate cables at the monitors. If you are looping to other devices, unterminate all but the last device.

MONITOR

LOOPING

MONITOR

Figure 8. Connecting Monitors

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARMS

The CM6800 provides numerous alarm handling options. Refer to the Programming section for a detailed description.

1. Connect wires from the sensors to the respective alarm input points on the connectors at the back of the CM6800. Each sensor

requires two wires – one wire to the alarm input terminal and a return wire to one of the ground terminals on the connector. The

CM6800 supports eight internal alarms.

Alarm sensors can be either N.O. (normally open) or N.C. (normally closed) contacts. The CM6800 is set to N.O. as a factory default.

2. If your system requires more than eight alarms, connect an ALM2064 unit to the system. Refer to the M Devices section.

010101

CONTROL

COM

120/230V~

50/60 HZ

25 WATTS

CM6800-32X6

ALM2064

Figure 9. Connecting Alarms

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING DEVICES THROUGH THE COMMUNICATION PORTS

The CM6800-32X6 Matrix Switcher/Controller provides five communication ports on the rear panel for connecting peripheral components.

Instructions are provided in this section for the most commonly used connections.

NOTE: Connection instructions for other periperal devices, such as the CM9760-MDA or CM9760-CDU-T, are provided as Pelco Technical

Tips. Connection instructions for compatible products, such as PelcoNet transmission systems and the VMX300 are provided in the

appropriate product installation manual.

PIN 1

PIN 8

PIN 1

PIN 5

PIN 9

PIN 6

Figure 10. Communication Port Inputs

Table B. Communication Port Devices and Wiring

Port

Input Type Wiring

Pin-Outs

Default Device

Programmable to Other Device(s)

DB9

RS-232

RS-485

Ground

PC Setup – CM6800MGR

program

ASCII device

RJ-45

Ground

ASCII device

Rx+

Rx-

Ground

Tx-

Tx+

M devices – ALM2064,

REL2064, KBD960

RJ-45

RS-485

Rx+

Rx-

Ground

Tx-

Tx+

Genex multiplexer

CM9760-MDA, ASCII, keyboards

(KBD100, 200A, & 300A)

RS-485

plus power

Rx+

Rx-

Keyboard (direct powered) –

KBD100, 200, & 300

KBD power (12V)

KBD Ground

Ground

Tx-

Tx+

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table C. Default Port Settings

Default Settings

Port

COM 1

COM 2

COM 3

COM 4

COM 5

MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit

ASCII, RS-232, 9600 baud, no parity, 8 data bits, 1 stop bit

M, RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit

MUX-GENEX, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

KBD-300A, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

NOTE: Refer to the Programming section for instructions on changing Port settings.

COM 3

M DEVICES (RS-485)

MAX # OF DEVICES = 6

MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)

USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR; 16 pF PER FT (pF =PICOFARADS)

STRAIGHT

CABLES

CM9505UPS

POWER

SUPPLY

ALM2064

NUMBER SUPPORTED = 2

64 ALARMS X 2 = 128 ALARMS

KBD960

REL2064

NUMBER SUPPORTED = 2

64 RELAYS X 2 = 128

KBD960

NUMBER SUPPORTED = 2

010101

COM 5

CONTROL

LOCAL KEYBOARDS (RS-485)

KBD100/200A/300A SERIES

MAX # OF DEVICES = 8

COM 2

(RS232)

ASCII CONTROL ONLY

COM

ALTERNATE EQUIPMENT

NOTE: TOTAL NUMBER OF

KBD100/200A/300A SERIES

KEYBOARDS CONNECTED

TO THE CM6800-32X6 CANNOT

EXCEED 8

120/230V~

50/60 HZ

25 WATTS

VIDEO

COM 1

PC SETUP

(RS-232)

COM 4

ALTERNATE

OPTION

RS-232 NULL

MODEM CABLE

12 V 50 Hz

TRANSFORMER

COM 4

GENEX (RS-485)

ALSO PROGRAMMABLE FOR KBD 100/200/300 SERIES,

CM9760-MDA, OR ASCII. MAX # OF DEVICES = 8

Figure 11. CM6800-32X6 Communication Port Connections and Options

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD100, KBD200A, AND KBD300A SERIES KEYBOARDS

You can connect up to eight KBD100/200A/300A Series keyboards to either of the following ports:

•

COM 4 (up to 8 remotely connected keyboards)

COM 5 (1 direct-powered keyboard or up to 8 remotely connected keyboards)

The total number of KBD100/200A/300A Series keyboards connected to the CM6800-32X6 cannot exceed eight.

KBD100, KBD200A, AND KBD300A: DIRECT-POWERED KEYBOARD

Use COM 5 (Serial Port 5) for a direct-powered local keyboard. COM 5 can power one KBD100/200A/300A Series keyboard.

If you are connecting more than one keyboard to COM 5, a KBDKIT(-X) is required for each keyboard. Refer to the KBD100, KBD200A, and

KBD300A: Remote Keyboards section.

1. Using the 25-foot (7.62 m) straight data cable supplied with the keyboard, plug one end into the RJ-45 connector on the rear of the

keyboard.

NOTE: If distance between CM6800 and keyboard exceeds 25 feet, use KBDKIT(-X).

KBD300A

Figure 12. Data Cable Plugged into Local Keyboard

2. Plug the other end of the data cable into COM 5 on the CM6800-32X6.

THE CM6800-32X6 CAN POWER ONE KBD 100/200A/300A SERIES KEYBOARD ON COM 5.

KBD100, KBD200A, KBD300A

CM6800-32X6 COM 5 KBD100, 200A, 300A

010101

RJ-45 PIN-OUTS

1 Rx+

2 Rx-

3 KBD 12V

4 KBD GROUND

5 GROUND

6 NC

1 Tx+

2 Tx-

3 12V

4 12V

5 GROUND

6 NC

CONTROL

7 Tx-

8 Tx+

7 Rx-

8 Rx+

COM

120/230V~

50/60 HZ

VIDEO

25 WATTS

Figure 13. Data Cable Plugged into COM 5

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Set the keyboard DIP switches for the desired address for the local keyboard (refer to Figure 12 and Table D).

Table D. Keyboard Addresses: KBD100/200A/300A Series Keyboards

Switch Settings

Keyboard

Address

OFF

Table E. Switch Settings – KBD200A/300A Keyboards Only

Switch

Keyboard

KBD200A

KBD300A

OFF

OFF (NOT USED)

OFF

ON or OFF*

* Switch 6 enables/disables turbo pan (can be switched while keyboard is on).

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD100, KBD200A, AND KBD300A: REMOTE KEYBOARDS

Use COM 4 or 5 for remote keyboard connections. Each port can support up to eight KBD100/200A/300A Series keyboards. Do not exceed

a total capacity of eight keyboards connected to the CM6800-32X6.

NOTE: A KBDKIT or KBDKIT-X is required to connect remote keyboards. The KBDKIT(-X) consists of two RJ-45 wall blocks and one

transformer. Use one wall block for each keyboard.

If using COM 4, you will need to change the settings (the default setting is for a Genex Multiplexer). Refer to the Programming section for

instructions.

1. Select a suitable location for each keyboard and wall block. Wall blocks must be within 6 feet (1.8 m) of a suitable electrical outlet.

Do not mount the wall blocks yet.

2. Connect each keyboard to a wall block, using the data cable supplied with the keyboard.

3. Remove the wall block covers and wire the connections between each wall block. Connect to a final wall block (which will be

connected to the CM6800).

Communication to the keyboards is RS-485. Pelco recommends using shielded twisted pairs cable that meets or exceeds the basic

requirements for EIA RS-485 applications.

4. At each wall block, wire the KBDKIT(-X) transformer to pins 3 and 4. Polarity is unimportant.

5. Replace the cover on the wall block. Secure the wall block to a suitable surface. A double-sided sticky pad is provided to mount the

wall block.

6. Set the address switches for each keyboard according to Table D.

7. Connect the final wall block to COM 4 or 5 on the CM6800-32X6, using a straight data cable (supplied with the CM6800).

010101

PT Z

CO NT RO

CM6800-32X6 COM 5

RJ-45 PIN-OUTS

KBD100, 200A, 300A

RJ-45 PIN-OUTS

Rx+

Rx-

KBD 12V

KBD GROUND

GROUND

1 Tx+

2 Tx-

CO M

GROUND

Rx-

120/230V~

50/60 HZ

25 WATT S

7 Tx-

8 Tx+

Rx+

WALL BLOCK

KBDKIT(-X)

KBD300A

KBD100

KBD200A

REMOTE KEYBOARDS

Figure 14. Remote Keyboards

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

M DEVICES

M protocol devices (KBD960/KBR960 keyboards, ALM2064 Alarm Interface Units, and REL2064 Relay Interface Units) can be connected to

COM 3 on the CM6800-32X6.

If only one device is to be connected to COM 3, use the instructions for that device in the following sections.

If more than one device is to be connected to COM 3, refer to the Multiple M Devices section.

Connect M devices to the CM6800 with straight cables. Two straight cables and one reversed cable are supplied with the CM6800 (save

the reversed cable for connecting a Genex Multiplexer, if applicable).

M Devices Addressing

Each M device connected to the CM6800 must have a unique local address within a range of 1-16. Use the hardware DIP switches to set

the appropriate ALM2064 and REL2064 local addresses. Specify the appropriate KBD960/KBR960 local address through the keyboard

Setup Mode after you complete the system installation (refer to the System Start-Up section).

For use with the CM6800, Pelco recommends numbering M devices in a sequential order. In a sample application, with two of each M

device, you might assign local addresses as follows:

M device local addresses:

KBD960/KBR960:

REL2064:

Default

Recommended for CM6800

1, 2

3, 4

5, 6

ALM2064:

NOTE: To use the CM6800 system access or keyboard priority features, you must address KBD960/KBR960 keyboards within a range of 1-8.

COMPARED "COLOR RUN"

IS IN OPPOSITE DIRECTION

COMPARED "COLOR RUN"

IS IN SAME DIRECTION

BROWN BROWN

BROWN

REVERSED CABLE

STRAIGHT CABLE

Figure 15. RJ-45 Cable Types

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting a Single KBD960/KBR960 Keyboard

To connect a single KBD960/KBR960 Keyboard to the CM6800:

1. Connect the keyboard to the CM9505UPS using the straight cable supplied with the keyboard.

2. Connect the CM9505UPS to COM 3 on the CM6800-32X6 using the 6-foot (1.8 m) straight data cable supplied with the CM6800.

NOTE: After completing system installation and power-up, you must configure the KBD960/KBR960 settings. Refer to the System Start-Up

section.

010101

CONTROL

COM 3 DEFAULT SETTINGS:

M, RS-485, 19200 BAUD,

NO PARITY, 8 DATA BITS,

1 STOP BIT

COM 1

120/230V~

50/60 HZ

VIDEO

25 WATTS

CABLE CAN BE

STRAIGHT (SUPPLIED)

OR REVERSED

CM9505UPS

RS-485

KBD960

RJ-45 PIN-OUTS

CM6800-32X6 COM 3

RJ-45 PIN-OUTS

STRAIGHT CABLE

(SUPPLIED)

1 Tx+

2 Tx-

1 Rx+

2 Rx-

3 NC

4 NC

5 GROUND

6 NC

7 Rx-

8 Rx+

7 Tx-

8 Tx+

KBD960

Figure 16. Connecting a KBD960/KBR960 to the CM6800-32X6

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting a Single ALM2064 Alarm Interface Unit

To connect a single ALM2064 Alarm Interface Unit:

1. Connect the ALM2064 OUT port to COM 3 on the CM6800-32X6 using the 6-foot (1.8 m) straight data cable supplied with the CM6800.

2. Set SW2, DIP switches 1-8 to the appropriate positions for the local address (default address setting is 1). Refer to the ALM2064

Alarm Interface Unit Installation/Operation Manual for instructions.

010101

CONTROL

COM 3 DEFAULT SETTINGS:

M, RS-485, 19200 BAUD,

NO PARITY, 8 DATA BITS,

1 STOP BIT

COM

120/230V~

50/60 HZ

25 WATTS

VIDEO

STRAIGHT CABLE

(SUPPLIED)

ALM2064

RJ-45 PIN-OUTS

CM6800 -32X6 COM 3

RJ-45 PIN-OUTS

RS-485

1 Tx+

2 Tx-

Rx+

Rx-

GROUND

ALM2064

Rx-

Rx+

7 Tx-

8 Tx+

CONNECT THROUGH

THE "OUT" PORT

Figure 17. Connecting a Single ALM2064 Alarm Interface Unit

Connecting a Single REL2064 Relay Interface Unit

To connect a single REL2064 Relay Interface Unit:

1. Connect the REL2064 OUT port to COM 3 on the CM6800-32X6 using the 6-foot (1.8 m) straight data cable supplied with the CM6800.

2. Set SW2, DIP switches 1-8 to the appropriate positions for the local address (default address setting is 1). Refer to the REL2064

Relay Interface Unit Installation/Operation Manual for instructions.

010101

CONTROL

COM 3 DEFAULT SETTINGS:

M, RS-485, 19200 BAUD,

NO PARITY, 8 DATA BITS,

1 STOP BIT

COM

120/230V~

50/60 HZ

25 WATTS

VIDEO

REL2064

RJ-45 PIN-OUTS

STRAIGHT CABLE

(SUPPLIED)

CM6800-32X6 COM 3

RJ-45 PIN-OUTS

1 Tx+

2 Tx-

Rx+

Rx-

GROUND

REL2064

Rx-

Rx+

7 Tx-

8 Tx+

CONNECT THROUGH

THE "OUT" PORT

Figure 18. Connecting a Single REL2064 Relay Interface Unit

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiple M Devices

Multiple M devices (KBD960/KBR960, ALM2064, and REL2064) can be connected to COM 3 on the CM6800-32X6, either as local devices

or remote devices (when connecting two KBD960/KBR960 keyboards to the CM6800, you must use a remote connection).

Multiple M Devices: Local Connection

1. If you are connecting a KBD960/KBR960, connect it to the CM9505UPS with the straight cable supplied with the keyboard. Then

connect the CM9505UPS to the IN port on the next unit (either the ALM2064 or the REL2064) with a 6-foot (1.8 m) straight cable

(supplied with the CM6800).

2. Connect each ALM2064 and REL2064 unit to the next unit with a 6-foot (1.8 m) straight cable (supplied with the CM6800) from the

OUT port to the IN port on the next unit. You can connect a maximum of two ALM2064 units and two REL2064 units to the CM6800.

3. Connect the last unit to the CM6800 with a 6-foot (1.8 m) straight cable (supplied with the CM6800) from the OUT port to COM 3 on

the CM6800-32X6.

COM 3

DEFAULT SETTINGS: M, RS-485, 19200 BAUD, NO PARITY, 8 DATA BITS, 1 STOP BIT

MAX # OF DEVICES = 6

MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)

USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR; 16pF PER FT (pF = PICOFARADS)

010101

CM6800-32X6

RJ-45 PIN-OUTS

CONTROL

1 Rx+

2 Rx-

STRAIGHT CABLES

(SUPPLIED)

GND

COM

7 Tx-

8 Tx+

CM9505UPS

120/230V~

50/60 HZ

VIDEO

25 WATTS

STRAIGHT CABLE

(SUPPLIED)

STRAIGHT CABLE

(SUPPLIED)

RS-485

ALM2064

KBD960

RJ-45 PIN-OUTS

1 Tx+

KBD960

2 Tx-

RJ-45 PIN-OUTS

REL2064

1 Tx+

2 Tx-

REL2064

RJ-45 PIN-OUTS

7 Rx-

8 Rx+

1 Tx+

2 Tx-

7 Rx-

8 Rx+

7 Rx-

8 Rx+

Figure 19. Connecting Multiple M Devices – Local Connection

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiple M Devices: Remote Connection

Use a remote connection when the distance from the CM6800 is greater than 6-feet (1.8 m).

1. Connect each ALM2064 and REL2064 unit to a wall block with a 6-foot (1.8 m) straight cable (supplied with the CM6800). You can

connect a maximum of two ALM2064 units and two REL2064 units to the CM6800.

2. If you are connecting a KBD960, connect it to the CM9505UPS with the straight cable supplied with the keyboard. Then connect the

CM9505UPS to a wall block with a 6-foot (1.8 m) straight cable (supplied with the CM6800). You can connect a maximum of two

KBD960 keyboards to the CM6800.

3. Connect the wall blocks to a final wall block. If additional wall blocks are needed, order part number CON12J008Z03G0Z.

4. Connect the terminal wall block to COM 3 on the CM6800-32X6 using a 6-foot (1.8 m) straight cable (supplied with the CM6800).

COM 3

DEFAULT SETTINGS: M, RS-485, 19200 BAUD, NO PARITY, 8 DATA BITS, 1 STOP BIT

MAX # OF DEVICES = 6

MAXIMUM DISTANCE FROM CM6800 = 3,940 FT (1,200 M)

USING 24 AWG COPPER, UNSHIELDED TWISTED PAIR; 16pF PER FT (pF = PICOFARADS)

010101

CM6800-32X6 COM 3

RJ-45 PIN-OUTS

CONTROL

1 Rx+

2 Rx-

GND

COM 1

7 Tx-

8 Tx+

120/230V~

50/60 HZ

25 WATTS

RS-485 STRAIGHT CABLE (SUPPLIED)

STRAIGHT CABLE

(SUPPLIED)

ALM2064

REL2064

KBD960

STRAIGHT CABLE

TO CM9505UPS

(SUPPLIED)

CONNECT THROUGH

THE "OUT" PORT

CONNECT THROUGH

THE "OUT" PORT

KBD960

RJ-45 PIN-OUTS

ALM2064

RJ-45 PIN-OUTS

REL2064

RJ-45 PIN-OUTS

1 Tx+

2 Tx-

1 Tx+

2 Tx-

1 Tx+

2 Tx-

7 Rx-

8 Rx+

7 Rx-

8 Rx+

7 Rx-

8 Rx+

Figure 20. Connecting Multiple M Devices – Remote Connection

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING A PC

The CM6800 provides PC-based setup and programming software that facilitates complete switcher programming and configuration.

Refer to the CM6800-MGR Quick Start Guide for instructions on using the software.

Connect a PC to the CM6800 to access the CM6800-MGR software or to download upgrades to the software.

1. Using a null modem cable (user-supplied), plug one end into the DB9 COM 1 port on the PC. (To use a PC port other than COM 1,

refer to the CM6800-MGR Installation/Operation Manual.)

2. Plug the other end of the cable into the DB9 COM 1 port of the CM6800.

NULL MODEM CABLE

PIN 1

PIN 5

CM6800 COM 1

DB9 PIN-OUTS

PC COM 1

DB9 PIN-OUTS

PIN 2 = RX IN

PIN 3 = TX OUT

PIN 5 = GND

PIN 2 = RX IN

PIN 3 = TX OUT

PIN 5 = GND

20015

PIN 9

PIN 6

Figure 21. PC Connection to DB9 Port

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTING GENEX MULTIPLEXERS

Use COM 4 to connect up to eight Genex Multiplexers to the CM6800-32X6.

1. Connect the COM IN port of the multiplexer to COM 4 on the CM6800-32X6, using the 6-foot (1.8 m) reversed data cable supplied

with the CM6800.

One reversed cable and two straight cables are supplied with the CM6800 (save the reversed cable for connecting a Genex

multiplexer, if applicable).

A straight data cable is supplied with the Genex multiplexer. Use this cable for connecting a second Genex multiplexer to the first

multiplexer, if necessary.

2. Connect the MAIN monitor output from the multiplexer to any of the camera inputs on the CM6800-32X6.

3. Connect cameras to the multiplexer and then loop them to the CM6800. Refer to the MX4000 Genex Series Simplex and Duplex

Multiplexers Installation/Operation Manual for detailed camera connection instructions. Terminate the video loop at the CM6800.

4. If required, you can connect a total of eight Genex multiplexers through COM 4. Daisy-chain the multiplexers by connecting a

straight data cable from the COM OUT port on the first multiplexer to the COM IN port on the second multiplexer; connect the COM

OUT port on the second multiplexer to the COM IN port on the third multiplexer. Continue to the eighth multiplexer, if necessary.

Refer to the System Start-Up section for additional configuration steps required when using a Genex Multiplexer.

010101

CONTROL

COM

120/230V~

50/60 HZ

25 WATTS

REVERSED CABLE

SPOT MAIN

VCR

IN COM OUT

ALARMS

OCC S

OUT

AUX

MONITOR SIGNAL OUT

110-240V 50/60 Hz

10 111213141516

SVHS

GENEX MULTIPLEXER

STRAIGHT CABLE

SPOT MAIN

AUX

VCR

SVHS

VCR

IN COM OUT

ALARMS

OCC S

OUT

110-240V 50/60 Hz

10 111213141516

SVHS

GENEX MULTIPLEXER

RJ-45 PIN-OUTS

CM6800-32X6 COM 4

RJ-45 PIN-OUTS

GENEX MULTIPLEXER

STRAIGHT CABLE

Rx+ 1

Rx- 2

12VAC (OUT) 3

12VAC (OUT) 4

GROUND 5

NC 6

1 Rx+

2 Rx-

3 NC

4 NC

5 GROUND

6 NC

SPOT MAIN

IN COM OUT

ALARMS

OCC S

OUT

AUX

110-240V 50/60 Hz

10 111213141516

SVHS

Tx- 7

Tx+ 8

7 Tx-

8 Tx+

GENEX MULTIPLEXERS-8 MAXIMUM

Figure 22. Connecting Genex Multiplexers

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

LOCAL AUXILIARIES

The CM6800-32X6 provides two local auxiliary (AUX) outputs on the rear panel for controlling VCRs, printers, and other devices. These

outputs can be activated directly from a keyboard by using the F1 and F2 function keys, or they can be activated by an alarm (determined

by programming). Both relay contacts and TTL outputs are used.

In addition, you can connect up to two REL2064 Relay Interface Units to the CM6800. Note that since operation of the two internal

auxiliary relays on the CM6800-32X6 will also operate the first two relays on the external unit, the maximum capacity of the system may

be limited to 128 auxiliaries (depending on how you number the external relays). Refer to the Connecting a Single REL2064 Relay Interface

Unit section for connection instructions.

Connecting Relay Contacts – AUX 1

AUX 1 is a dry contact relay output. Terminal connections are provided for both normally open (N.O.) and normally closed (N.C.) contacts.

Refer to Figure 23 for wiring details. Note that this figure shows the wiring for a normally open contact. For a normally closed contact,

move the wire from the N.O. terminal to the the N.C. terminal.

Do not exceed the voltage and current ratings for the relay contacts.

You will need to provide an external power source to operate your device. In most cases you will also need an external current limiting

resistor. The formula for calculating the resistor value is given in Figure 23.

12-PIN PLUG-IN

CONNECTOR

AUX 1 RELAY

CONTACT RATINGS

CURRENT

VOLTAGE

0.3A

0.5A

30 VDC

110 VDC

125 VDC

EXTERNAL

DEVICE

+VPS -VPS

+VPS

= OPERATING CURRENT OF THE EXTERNAL DEVICE (MUST NOT EXCEED AUX 1 CURRENT RATING.)

= RATED OPERATING VOLTAGE OF THE EXTERNAL DEVICE.

= CURRENT LIMITING RESISTOR.

= VOLTAGE OF THE EXTERNAL POWER SOURCE (MUST NOT EXCEED VOLTAGE RATING FOR THE

ASSOCIATED CURRENT). VPS CAN BE AC OR DC.

= NEGATIVE, COMMON OR GROUND TERMINAL OF EXTERNAL POWER SOURCE (AC OR DC).

-VPS

FORMULAS FOR R VALUES

R (OHMS)

VPS - V_O

I_O

P (WATTS)

(I_O) X R

Figure 23. Wiring the AUX 1 (Relay) Output

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting the Open Collector output – F2 (TTL)

F2 is a TTL open collector output. This output provides a path to ground to control the low voltage trigger input on many devices. It can

control higher voltage control inputs via isolation relays. Refer to Figure 24 for wiring details.

Do not exceed the voltage and current ratings for the TTL output.

An external pull-up resistor is usually necessary. The formula for calculating the resistor value is given in Figure 24.

+VDC

12-PIN PLUG-IN

CONNECTOR

R = +VDC

25 mA

INPUT

DEVICE EXAMPLE: VIDEO PRINTER

20018

FROM VIDEO OUTPUT

LOOPED TO MONITOR

+VDC = VOLTAGE OF THE EXTERNAL POWER SOURCE.

NOTE: +VDC SHOULD BE 5V OR GREATER, BUT NOT

EXCEED 15V OR THE MAXIMUM RATED OUTPUT

VOLTAGE FOR THE DEVICE INPUT. +VDC CAN

ONLY BE DC.

Figure 24. Wiring the F2 (TTL) Output

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM START-UP

After completing the system installation, follow the procedure below to start proper system operation. Skip any “system-specific” steps

that do not apply to your system setup.

POWER-UP THE SYSTEM

Plug the CM6800 power cord into a 120/230V, 50/60 Hz power source. Plug in and turn on all devices connected to the CM6800.

Once the system is powered-up you will see video from camera 1 and the following time/date stamp on all system monitors:

00620

Figure 25. CM6800 Time/Date Stamp on Monitor

The time stamp will be advancing in one-second increments. Wait five seconds before proceeding.

INITIALIZE KEYBOARDS

Specify a monitor for each keyboard after your first power-up or any time power is cycled to the keyboard or the CM6800.

Always allow five seconds to elapse before specifying a monitor.

1. Enter a number corresponding to the monitor output that is feeding the monitor you are viewing.

2. Press the MON key. The keyboard LED displays the number you entered. This also confirms successful communication between the

keyboard and the CM6800. If the keyboard LED does not display the monitor number, repeat 1 and 2.

CONFIGURE THE SYSTEM

The CM6800 is shipped from the factory with default programming settings. If the defaults are acceptable, the CM6800 can be operated

without any user programming. However, you may want to program the following basic system settings:

•

Time and date.

Camera titles: by default, each camera is titled “CAM #” (# = camera number).

Camera video source: Extended Coaxitron protocol receivers can be operated without any programming changes. For other receiver

control protocols, access the Camera programming screen to select the control type for the device connected to each video input.

•

Alarms: The CM6800 is shipped from the factory with the alarm contact enable field set to OFF. To use the alarm features, access

the Alarm programming screens to enable the alarm contact.

In addition, some or all of the following configuration steps may be necessary, depending on your system. Configure the CM6800 through

Programming mode. Refer to the Programming section for detailed instructions.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMUNICATION PORTS

If you are using any communication port for a device not specified by the default setting, open the Port programming screen to change the

settings.

Table F. Default Port Settings

Port

Default Settings

COM 1

COM 2

COM 3

COM 4

COM 5

PTZ (Port 6)

MGR, RS-232, 56000 baud, no parity, 8 data bits, 1 stop bit

ASCII, RS-232, 9600 baud, no parity, 8 data bits, 1 stop bit

M, RS-485, 19200 baud, no parity, 8 data bits, 1 stop bit

MUX-GENEX, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

KBD-300A, RS-485, 9600 baud, odd parity, 8 data bits, 1 stop bit

PTZ-P, RS-422, 4800 baud, no parity, 8 data bits, 1 stop bit

KBD960/KBR960 KEYBOARD

Configure the KBD960/KBR960 settings.

1. Set DIP switch 2 to the ON position.

2. Enter Setup Mode. Set the local address (1-8). (Note: the baud rate is set by default to 19200.) Each M device connected to the

CM6800 must have a unique local address. Refer to the KBD960/KBR960 Keyboard Installation/Operation Manual for detailed setup

instructions.

3. Return DIP switch 2 to the OFF position.

4. Press the EXIT icon on the keyboard LCD screen.

GENEX MULTIPLEXER

Access the Camera programming screen and specify MUX control for all cameras connected to the CM6800 through the Genex Multi-

plexer.

Access the CM6800 Camera programming screen to configure the following camera control options for each camera connected to the

CM6800 through the Genex Multiplexer:

•

CONTROL: MUX

PORT ADDRESS: assign the appropriate address. The port address must match the “Unit ID” assigned through the Genex

programming screens.

You must also configure the Genex Multiplexer. Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/

Operation Manual for instructions on accessing the Advanced System Setup programming screen. Select the following options:

•

SPOT MONITOR DISPLAY: TRACK MAIN

UNIT ID (must match the port address assigned through the CM6800)

COMM. TYPE: SLAVE (each multiplexer connected to the CM6800 must be in slave mode)

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MONITOR COLOR ADJUSTMENT:

Once you have connected all devices and powered the system, use the CM6800 color bars as a reference tool for adjusting the color on

each monitor.

1. Enter 9999.

2. Press the CAM key. Broadcast quality color bars appear on the monitor.

3. Adjust color on each monitor as necessary until the color bars match the following color order on the monitor (for black and white

monitors you can use the color bars to adjust brightness):

00630

Figure 26. CM6800 Color Bars

PROGRAM PRESETS

Program presets as necessary for your system. Refer to the appropriate keyboard manual for instructions.

ADDITIONAL PROGRAMMING

Refer to the Programming section for complete instructions on programming the CM6800.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING THE CM6800

The CM6800 is shipped from the factory with default programming settings. If the defaults are acceptable, the CM6800 can be operated

without any user programming. However, you may want to program the following basic system settings:

•

Time and date

Camera titles

PTZ control via hardwire data connections

Alarm contacts

Alarms must be enabled before they are functional.

•

Access/Partitioning

All access is set to YES by factory default.

Communication ports

To connect remote keyboards to COM 4 (the alternate connection shown in the Quick Start Guide), change the Port 4 settings.

Pelco provides two options for programming the CM6800 to your specifications:

•

Password-protected, on-screen programming screens accessible directly from the Matrix Switcher

PC-based CM6800-MGR software

Refer to the CM6800-MGR Quick Start Guide for instructions on accessing and using this software to program your system.

NOTE: Pelco strongly recommends uploading your programming settings to the CM6800-MGR to save settings in the event of an

accidental reset.

The CM6800 allows system programming from only one monitor at a time. If programming from the CM6800-MGR is sent to the CM6800

at the same time that you are programming from a monitor screen, the system will exit the on-screen programming function.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CM6800 PROGRAMMING MODE

1. If you have not already done so, select the monitor (KBD960/KBR960: if the Camera menu appears, press

to exit).

PGM

2. Press the PGM key or select

on the KBD960/KBR960). The Password screen appears.

DEF

Note that on the KBD960/KBR960, you must first select

and

. Then enter the Define PIN (Default: 1234), and select

PELCO VIDEO SWITCHER

MODEL CM6800

PASSWORD TO MAIN MENU

*******

SCRATCHPAD SEQUENCE

MACRO STATUS VIEW

RETURN

20019

Figure 27. CM6800 Password Screen

3. At the ******* prompt, enter the DEFAULT PASSWORD: 2899100

The Main Menu appears.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

Figure 28. CM6800 Programming Main Menu

Select Language

If necessary, select the appropriate language.

1. Navigate to the language displayed below the menu options.

2. Scroll through the languages and select the language appropriate for your system.

3. Navigate to the RETURN field and navigate left or right to return to the Main Menu.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Exit Programming Mode

KBD100/200A/300A Keyboards

KBD960/KBR960 Keyboards

To return to active video you can:

PGM

To return to active video you can:

•

Press the PGM key once while in the Main Menu.

Menu.

once while in the Main

•

Select

Press the PGM key twice from anywhere else in the

programming screens.

PGM

the programming

•

Select

twice from anywhere else in

screens.

•

Navigate to the RETURN field and navigate left or right to

return to the previous screen or menu.

•

Navigate to the RETURN field and navigate left or right to

return to the previous screen or menu.

NAVIGATE AND SELECT OPTIONS/FIELD ENTRIES IN PROGRAMMING MODE

During programming, a menu appears on the monitor screen. The currently selected field blinks. Use the following keys or joystick on your

keyboard to navigate the programming screens.

Function

Keyboard

Navigate programming screens.

KBD100

Use the sequence and macro keys.

Left

Right

Down

MAC

HOLD

KBD200A

Use the Pan/Tilt positioning keys.

Left

Right

Down

KBD300A

Use the joystick.

Left

Right

KBD960/KBR960

Use the joystick. (See above icons)

Select the appropriate icon on the KBD960/KBR960 LCD SCREEN.

Left Right Up Down

Access a screen from the Main Menu (or from a submenu).

All Keyboards

1. Navigate down to the desired menu option.

2. Navigate left or right to select the menu option.

1. Using the numerical keypad, enter the number of the menu

option.

2. Press F1 on the KBD100/200A/300A keyboard or select

on the KBD960/KBR960 keyboard.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Function

Keyboard

Scroll through options in programming fields.

KBD100/200A/300A

Use F1 and F2. Or (KBD300A only) use the joystick to navigate

left or right.

NOTE: The joystick does not scroll options in all fields.

KBD960/KBR960

joystick to navigate left

icons or use the

Select the

or right.

NOTE: The joystick does not scroll options in all fields.

All keyboards

Select option in a programming field.

1. Scroll through the options until the appropriate entry

appears in the field.

2. Navigate to the next field or press PGM to exit.

NOTE: On the Monitor and Time & Date screens you must

apply the changes (refer to Time & Date or Monitor in this

section).

Enter a numerical value in an option

field (not available in all fields).

All keyboards

1. Using the numerical keypad, enter a number within the

range of valid options (example: to enter an internal alarm

contact you must enter a number between 1 and 8).

2. Press F1 on the KBD100/200A/300A keyboard or select

on the KBD960/KBR960 keyboard.

All keyboards

Access the HELP screen

(Sequences, Macros, and Alarm Group screens).

1. Navigate to the HELP field.

2. Press F1.

Access the NEXT or PREVIOUS page of a list (not available on

every screen).

All keyboards

1. Navigate to the NEXT or PREVIOUS field.

2. Press F1.

Exit a screen.

All keyboards

1. Navigate to the RETURN field.

2. Navigate left or right.

Press the PGM key to return to the previous screen or menu.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESS

The CM6800 supports the following system partitioning to control switching system access:

Keyboard to Monitor: Restrict a keyboard from accessing selected monitors.

Camera to Keyboard: Restrict a keyboard from calling selected cameras to monitors. Or video viewing only: permit the viewing of

selected cameras while preventing pan and tilt control.

Camera to Monitor: Restrict the viewing of selected cameras on selected monitors.

All system access is set to YES by default.

NOTE: To restrict access for keyboards, all keyboard addresses must be within a range from 1-8.

NOTE: If you connect an ASCII keyboard/device to the CM6800 (COM port 1, 2, or 4), you can connect only one

keyboard to a port. Specify access in the first column only (address 1).

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA TO KEYBOARD ACCESS

ACCESS

PORT 5

KEYBOARD

KEYBOARD TO MONITOR

CAMERA TO KEYBOARD

CAMERA TO MONITOR 1-6

CAM

0001

0002

0003

0004

0005

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00636

00654

00644

Figure 29. Sample Access Screen

1. Select the COM port number for which you are programming access control.

2. In the Access matix, configure the specific access allowed for each device.

Keyboard to Monitor

In each monitor row specify the access allowed for each keyboard to control each specific monitor.

Y = Yes; control is allowed

N = No; control is not allowed

Camera to Keyboard

In each camera row specify the access allowed for each keyboard to view and control the specific logical camera number.

Y = Yes; viewing and control is allowed

N = No; viewing and control is not allowed

V = View only; camera can be viewed but not controlled

Camera to Monitor

In each camera row specify the access allowed for each monitor to display the specific logical camera number.

Y = Yes; camera can be viewed

N = No; camera cannot be viewed

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARM PROGRAMMING

Alarmed cameras can be displayed on one or several monitors as part of one or several alarm groups (each monitor can display only one

alarm group.)

Before programming alarm settings note the following precautions:

•

Verify that no automated system functions are set to run, such as a macro that would arm or disarm an alarm.

Ensure that system operators do not arm or disarm any alarms while you are programming alarm settings.

NOTE: You cannot access the Alarm Contacts screen when an alarm is active. If an alarm is triggered while you are in the CM6800

programming screens, the system will exit the on-screen programming function and display the alarm on the appropriate monitor(s).

Complete the following steps to program alarms:

1. Program the alarm display format for each alarm group. An alarm can include up to eight steps, so eight camera views could display

as a part of each alarm. Refer to Program Alarm Groups.

2. Program the individual alarm contact. Refer to Program an Internal or External Alarm Contact.

PROGRAM ALARM GROUPS

Use the Alarm Group screen to configure alarm groups to appear on system monitors. To display on a monitor, an alarm must be assigned

to an alarm group.

PELCO SWITCHER

ALARM CONTACTS

MODEL CM6800

MAIN MENU

ALARM MONITOR GROUP SETUP

INTERNAL CONTACT

EXTERNAL CONTACT

VIDEO LOSS

CAMERA

MON

—

LOGICAL CAMERA

MONITOR

ACCESS

—

ALARM GROUP

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

—

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

HELP

RETURN

ENGLISH

RETURN

00654

00642

00637

Figure 30. Program Alarm Groups

Specify the display option for up to six alarm groups. Refer to the on-screen Help or to the Alarm Group Display Options in the Appendix

for a description of each display option.

Display Option Entry

Display Option Type

Block build

Number of Monitors Displaying Each Alarm Group

Up to six

D and Q

M and L

Chronological pair

Reverse chronological pair

Salvo group

One display monitor (D), one queue monitor (Q)

One display monitor (M), one queue monitor (L)

From two to six

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

INTERNAL AND EXTERNAL ALARMS

Use the Alarm Contact screens to configure alarm inputs. When an alarm is triggered, the alarm icon and the alarm letter (“I” for internal;

“E” for external) appear on monitors programmed through the Alarm Group screen to display the alarm.

INTERNAL ALARM MENU

CONTACT:

ACK TYPE: MANUAL

TYPE:

ENABLE:

TIME OUT: 10

PRIORITY:

OFF

DWL CMD

01 PRES

STP CAM

## AUX

0001

— — — —000

— — — —00

PELCO SWITCHER

MODEL CM6800

MAIN MENU

ALARM CONTACTS

INTERNAL CONTACT

EXTERNAL CONTACT

VIDEO LOSS

CAMERA

GROUP ENABLE

LOGICAL CAMERA

MONITOR

ACCESS

ALARM GROUP

RETURN

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

00650

10 ALARM CONTACTS

11 EVENT TIMER

EXTERNAL ALARM MENU

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

CONTACT: 001

ACK TYPE: MANUAL

ENABLE:

TIME OUT: 10

OFF

PRIORITY:

ENGLISH

RETURN

STP CAM

DWL CMD

AUX

0001

— — — —00

— — — —000

— — — —00

00654

00642

GROUP ENABLE

RETURN

00649

Figure 31. Program an Internal or External Alarm

1. Select the alarm input number in the CONTACT field.

Internal Alarm screen: Configure any of the eight internal alarm inputs on the CM6800 rear panel. Internal inputs are programmable

to associate any camera to any input.

External Alarm screen: Configure any of the external alarms. A maximum of two external ALM2064 Alarm Interface Units can be

connected to the CM6800-32X6, providing up to 128 external alarm inputs.

2. Select ON in the ENABLE field.

3. In the STP matrix, configure up to eight steps to be triggered as a result of this alarm.

a. In the CAM field select a camera (use the logical camera number) to be displayed on a system monitor.

b. In the DWL field, enter the amount of time the camera view is displayed in an alarm sequence; enter a dwell time between 1

and 99 seconds.

c. Optional:

In the CMD field, select a camera operation; if you select a macro, pattern, or preset, enter a valid macro, pattern, or preset

number in the ## field:

MACRO = macro (only the first three steps can be used when selecting a macro; each step must call a macro)

PRES = preset

PATT = pattern

RSCN = random scan

FSCN = frame scan

SSCN = stop scan

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

In the AUX field, select an auxiliary to be activated.

GON = turn global auxiliary on

GOFF = turn global auxiliary off

CON = turn camera auxiliary on

COFF = turn camera auxiliary off

NOTE: Activate the auxiliaries on the rear panel of the CM6800 by selecting global auxiliary numbers 1 or 2. The remaining

global auxiliary numbers control auxiliaries in up to two REL2064 Relay Interface Units.

4. In the GROUP ENABLE field, select ÒYÓ under the appropriate group letter to assign the alarm contact to one or more alarm groups.

Refer to the Program Alarm Groups section for information on alarm group display options.

NOTE: Verify that the monitor specified by the alarm group has access to the camera view(s) triggered by this alarm. If an alarm is

cued to a monitor that does not have access to the appropriate cameras, the camera views cannot be monitored.

5. Optional: The remaining alarm contact fields are configured with factory default settings; customize your system as necessary, by

changing the following settings:

ACK TYPE: The alarm clearance type is set to MANUAL by default, requiring an operator to acknowledge an alarm from a system

keyboard. If you select AUTO, the alarm will time out automatically after the interval specified in the TIME OUT field.

TYPE: Internal alarms are set by factory default as N.O. (normally open). Select N.C. for normally closed operation. Set the external

alarm input type through the ALM2064 Alarm Interface Unit.

PRIORITY: Select 1 for a priority alarm, which appears on system monitors before a non-priority (0) alarm.

PROGRAM A VIDEO LOSS ALARM

Use the Video Loss screen to program the CM6800 to detect video loss from any camera input and indicate the loss through alarm mode –

the logical alarm number, the alarm icon and a “V” (for video loss) appear on system monitors as specified by alarm group assignment.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

ALARM CONTACTS

VIDEO LOSS MENU

PHYSICAL INPUT:

INTERNAL CONTACT

EXTERNAL CONTACT

VIDEO LOSS

CAMERA

ENABLE: OFF

LOGICAL CAMERA

MONITOR

ACCESS

ACK TYPE: MANUAL

CAMERA 0001

TIME OUT: 10

ALARM GROUP

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

GROUP ENABLE

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

RETURN

ENGLISH

RETURN

00654

00642

00663

Figure 32. Program Video Loss Alarms

1. Select the PHYSICAL INPUT number; the logical camera number associated with the physical input appears in the CAMERA field.

2. Select ON in the ENABLE field.

3. In the GROUP ENABLE field, select “Y” under the appropriate group letter to assign the alarm contact to one or more alarm groups.

Refer to the Program Alarm Groups section for information on alarm group display options.

4. Optional: The ACK TYPE (alarm clearance type) field is set to MANUAL by default, requiring an operator to acknowledge a video

loss alarm from a system keyboard. If you select AUTO, the alarm will time out automatically after the interval specified in the TIME

OUT field.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUXILIARY OUTPUTS

The two local auxiliary (AUX) outputs on the rear panel of the CM6800-32X6 can be operated manually from a system keyboard or

automatically in response to an alarm.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

SET AUXILIARY MENU

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

AUX

MODE

ALM

LAT

MON

—

DWL

—

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00643

00654

Figure 33. Program Auxiliary Outputs

Latching or Momentary Operation

In the MODE field for each auxiliary, select either LAT or MOM.

Alarm-based Operation

1. In the MODE field for each auxiliary, select ALM.

2. In the MON field, select the monitor the auxiliary will follow.

3. In the DWL field, enter the number of seconds the auxiliary will remain active after there is no longer an alarm displayed on a

system monitor. The alarm is displayed on a monitor until

•

the alarm is acknowledged manually (if MANUAL is selected in the alarm contact ACK TYPE field),

the alarm contact times out (if AUTO is selected in the alarm contact ACK TYPE field).

Refer to the ACK TYPE description in Program an Internal or External Alarm Contact.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CAMERA PROGRAMMING

Extended Coaxitron protocol receivers can be operated without any programming changes, other than changing the camera title, if

necessary. For other receiver control protocols, you must select the control type for the device connected to each video input.

If necessary, first program logical camera number.

PROGRAM LOGICAL NUMBERS

Default logical numbers start at 0001 and continue sequentially to 0032. To use a different numbering scheme, program new numbers on

the Logical Camera Number screen.

PELCO SWITCHER

LOGICAL CAMERA NUMBER MENU

MODEL CM6800

MAIN MENU

PHY

LOG PHY

LOG

0001 17

0002 18

0003 19

0004 20

0005 21

0006 22

0007 23

0008 24

0009 25

0201 26

0202 27

0203 28

0301 29

0302 30

0303 31

0401 32

0402

0403

0404

0405

0500

0501

0502

0503

0504

0505

0601

0602

0603

0604

0605

0032

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00652

Figure 34. Program Logical Camera Numbers

The numbers in the PHY columns are the physical input numbers; each represents an actual BNC input on the rear panel of the CM6800

and cannot be changed.

In the LOG field for each physical camera input, assign a valid logical number (0001-9998). A valid number is any number from 0001 to

9998 that has not already been assigned to a physical camera input.

NOTE: If you change a logical number, you cannot control the camera until you select the new logical number from the keyboard.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAM CAMERAS

PELCO SWITCHER

MODEL CM6800

MAIN MENU

CAMERA 0001

CAMERA

VERTICAL DRIVE: OFF

EXT COAX

PORT ADDRESS: 01

LOGICAL CAMERA

MONITOR

ACCESS

CONTROL:

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

CAMERA TITLE

CAM 1

SELECT CHARACTER

RETURN

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

Figure 35. Program Cameras

1. In the CAMERA field, select the logical camera number of the video input to be defined.

2. In the CONTROL field, select the receiver control type.

EXT COAX: Coaxitron extended mode (32-bit)

STD COAX: Coaxitron standard mode (15-bit)

MUX: Genex multiplexer

PTZ-A: RS-422 Control Port A

M-02: Reserved for future use

M-08: Reserved for future use

NOTE: If you select PTZ-A you must also program Serial Port 6 (refer to Ports in this section).

3. The PORT ADDRESS field is required for Genex or RS-422 control only.

Genex multiplexer: Select the address of the multiplexer (01-32); this address must match the unit ID specified through

multiplexer programming. Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual.

RS-422 cameras: Select the camera/device address for RS-422 control (01-32). The port address must match the address setting

configured through the camera/receiver DIP switch settings.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Select the camera title. This title (up to 20 characters) appears on the monitor during real-time camera display.

a. Navigate to the position in the camera title that you want to change.

b. Use F1 and F2 to scroll through the camera title characters; once you reach the desired character for that position, navigate to

the next position.

The default title characters are 26 upper case letters and the numbers 0-9. You can add special characters through the Select

Characters screen (described below), or through the CM6800-MGR.

Select Character:

a. Navigate to the SELECT CHARACTER field and navigate left or right. The Select Character screen appears.

b. To select a character for the first position in the camera title, navigate to the desired character in the font table, and then press F1.

The designated character is displayed in the first position, and the POSITION field increments to position number 02.

Optional: Navigate to the POSITION field and use F1 and F2 to scroll through the camera title position numbers.

c. Navigate to the desired character in the font table for the next position, and then press F1. Continue until the camera title is

complete.

NOTE: You must also configure the camera/receiver. Refer to the appropriate camera/receiver installation manual.

Program Vertical Drive Option (Optional)

Select ON in the VERTICAL DRIVE field to provide the camera with a synchronization pulse via the coax cable.

NOTE: You can use the vertical drive option with any Pelco camera that supports the Pelco V-Sync feature.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

EVENT TIMERS

You can automate system operation to activate sequences or macros on specific monitors. Events can be scheduled on a daily or weekly

basis, or on a specific date such as a holiday. If you set more than one timer to start at the same time, the timers will run in the following

order of precedence: weekly, special, daily.

On each event timer screen:

•

Two methods are provided for selecting the event time: scrolling through time values or entering a valid hour and minute.

Each timer can activate either a macro or a sequence. Select a value for either the MACRO field or the SEQ field.

A macro started by an event timer runs until the last step is completed (unless you specify a loop in the macro).

A sequence started by an event timer runs continuously until another sequence or macro begins, or until a system operator selects a

different camera.

PELCO SWITCHER

EVENT TIMER

MODEL CM6800

DAILY TIMER 01

MAIN MENU

DAILY TIMER

WEEKLY TIMER

SPECIAL TIMER

ENABLE:

TIME:

OFF

12:02

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

RETURN

MACRO 00

MON SEQ

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

RETURN

ENGLISH

RETURN

00647

00654

00648

Figure 36. Sample Event Timer Programming

1. Select the timer number.

2. Select ON in the ENABLE field.

3. Set the hour and minute at which the event is to begin (24-hour time) in the TIME field.

4. Special timers only: select the date on which the event is to begin (DD-MM-YY).

5. Select the event to be activated by the event timer.

To select a macro, select a macro number. For a weekly timer specify the macro in the column under the desired day of the week.

To select a sequence, select a sequence number to run on a specific monitor. For a weekly timer specify the sequence in the column

under the desired day of the week

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MACRO

Macros simplify operator control by grouping multiple functions into a single command.

MACRO MENU

PELCO SWITCHER

MODEL CM6800

MAIN MENU

MACRO 01

STP CMD

HELP

MON DWL

CAM

SWT

000

0001

0002

0003

0004

0005

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

0017

0018

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

PRES 001

— — — —000

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00653

00654

Figure 37. Access the Macro Screen

MACRO:

STP:

Select the macro number you want to program.

Each macro can include up to 72 steps. For each step select entries for the following fields as necessary:

CMD:

Select a command. In addition, enter a valid number in the specified additional field(s); for example, if you

select PATT, enter a pattern number in the Command # field, a camera number in the Camera field, and a

monitor number in the Monitor field.

Refer to Table H in the Appendix for a description of each command and the additional fields required for each

command.

##:

If applicable, enter a valid number associated with the command selected.

CAM:

If applicable, enter a logical camera number. To select logical numbers other than the default numbers (1 to 32),

you must first program the logical numbering in the Logical Camera window. Refer to the Logical Camera

Numbers section.

MON:

DWL:

If applicable, enter a monitor number.

If desired, enter a dwell time (1-99 seconds); the dwell time is the period the macro halts before continuing to

the next step. The default dwell time is two seconds.

MACRO STATUS VIEW SCREEN

The Macro Status View screen provides a status view of each system macro (1-32). For each active macro the current status (RUN or

HOLD) and the number of the next macro step is displayed. If a macro is not running, the status is IDLE and the step number is 00.

A system operator can display the Macro Status View screen without entering password- protected programming screens.

MACRO STATUS

MAC

STATUS

RUN

IDLE

HOLD

IDLE

RUN

IDLE

STEP

MAC

STATUS

HOLD

RUN

IDLE

STEP

PELCO VIDEO SWITCHER

MODEL CM6800

PASSWORD TO MAIN MENU

*******

SCRATCHPAD SEQUENCE

MACRO STATUS VIEW

RETURN

20019

REFRESH

EXIT

20022

Figure 38. Macro Status View Screen

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MONITOR DISPLAY

Use the Monitor screen to adjust monitor display settings for your system. You can adjust settings for the current monitor only (CURRENT)

or for all system monitors (ALL).

PELCO SWITCHER

MODEL CM6800

MAIN MENU

MONITOR CURRENT

CAMERA NUMBER:

CAMERA TITLE:

R/X TYPE:

MON/ALM NUMBER:

MON/ALM STATUS:

TIME:

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

DATE:

BRIGHTNESS

POSITION DISPLAY

SET ALL

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

RETURN

ENGLISH

RETURN

00654

00655

Figure 39. Access the Monitor Screen

MONITOR:

Select CURRENT to program the monitor display for the monitor you are currently operating or ALL for all

monitors connected to the CM6800.

If you select ALL, you must navigate left or right in the SET ALL field to apply programming changes (refer to the

SET ALL field description).

0001

CAM 1

01-JAN-01 01:01:01

CAMERA NUMBER:

CAMERA TITLE:

R/X TYPE:

Enable (ON) or disable (OFF) on-screen display of the logical

camera number.

0001

CAM 1

01-JAN-01 01:01:01

Enable (ON) or disable (OFF) on-screen display of the camera

title (maximum of 20 alphanumeric characters).

Enable (ON) or disable (OFF) on-screen display of the camera

control type. The letter displayed on the monitor reflects the

receiver control type selected in the CONTROL field on the

Camera screen.

0001

CAM 1

01-JAN-01 01:01:01

R/X TYPE DISPLAY VALUES:

E = Coaxitron extended mode (32-bit)

S = Coaxitron standard mode (15-bit)

M = Genex multiplexer

P = PTZ-P (RS-422 through Control Port PTZ-A)

D = PTZ-D (RS-422 through Control Port PTZ-A)

MON/ALM NUMBER: Enable (ON) or disable (OFF) on-screen display of the monitor/

alarm number. During normal operation, the monitor number

appears in this field. The monitor number is a fixed number,

representing an actual BNC output on the rear panel of the

CM6800. When an alarm is active, the alarm number appears in

this field. The alarm number is either the physical alarm input

number of an internal alarm contact, or the address of an

0001

CAM 1

01-JAN-01 01:01:01

external alarm contact as configured on the Alarm Interface Unit.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MON/ALM STATUS:

Enable (ON) or disable (OFF) on-screen display of the monitor or

alarm status.

0001

CAM 1

01-JAN-01 01:01:01

MONITOR STATUS DISPLAY VALUES:

Blank = normal status

H = hold

S = sequence

NOTE: If an operator presses the HOLD key while an alarm

appears on the monitor, the H does not appear. The alarm icon

and alarm status value blink to indicate the HOLD status.

ALM STATUS DISPLAY VALUES:

I = internal alarm

0001

CAM 1

01-JAN-01 01:01:01

E = external alarm

V = video loss alarm

00634

TIME:

Enable (ON) or disable (OFF) on-screen display of the time as

programmed in the system.

0001

CAM 1

01-JAN-01 01:01:01

DATE:

Enable (ON) or disable (OFF) on-screen display of the date as

programmed in the system.

BRIGHTNESS:

Select the brightness level of the on-screen display (1-8; 8 = white characters, 1 = black characters; 2-7 = shades

of gray).

If you select CURRENT in the MONITOR field, you can see the brightness level change as you scroll through the

options.

If you select ALL in the MONITOR field, the changes do not take effect until you apply changes in the SET ALL

field.

POSITION DISPLAY:

Navigate left or right to select the Test Positioning Menu.

TEST POSITIONING MENU

---

The real-time camera display appears with Test Positioning Menu text

superimposed on the screen. Use the position keys or joystick to move

the text to the desired position on the screen. The text moves one line or

character position at a time.

PRESS PGM EXIT

00633

Press the PGM key to exit the test positioning menu.

SET ALL:

To apply monitor display changes to all system monitors (if you selected ALL in the MONITOR field) you must

navigate left or right in the SET ALL field; otherwise monitor display settings are not changed.

If you selected CURRENT in the MONITOR field, navigating left or right in the SET ALL field has no effect.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

PASSWORD

Use the Set Password screen to change the system password.

If you change the password and then forget the new one, you will have to reset the system to the factory defaults. All system program-

ming will be lost. Pelco recommends uploading your programming settings to the CM6800-MGR before changing the password. This

allows you to download the previous system settings, in the event of a system reset. If necessary, refer to the Troubleshooting section for

the system reset procedure.

PELCO SWITCHER

SET PASSWORD

MODEL CM6800

MAIN MENU

OLD PASSWORD: *******

NEW PASSWORD: *******

VER PASSWORD: *******

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00656

00654

Figure 40. Access the Set Password Screen

Use the numerical keypad to enter the old and new passwords. The password must be seven digits.

1. Enter the current password (Default: 2899100).

2. Enter the new password.

3. Enter the new password again as a verification check.

Once the new password is accepted, the Main Menu appears.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

PORTS (SERIAL/COM PORTS)

Use the Port screen to configure the settings for each device connected to a Serial/COM port on the rear panel of the CM6800.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

SET SERIAL PORT 05

DEVICE:

TYPE:

BAUD RATE:

PARITY:

DATA BITS:

STOP BITS:

KBD300

RS485

9600

ODD

CAMERA

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

REPORT ALARMS: - - -

RETURN

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00654

00657

Figure 41. Access the Port Screen

1. Select the number of the desired Serial Port/COM port (01-06). The serial port numbers correspond to the communication ports on

the CM6800-32X6 rear panel as follows:

Serial Port

Input on CM6800-32X6 rear panel

COM 1 DB9 input

02-05

COM 2-5 RJ-45 inputs

PTZ control input

2. Select the device connected to the COM port; the values in the TYPE, BAUD RATE, PARITY, DATA BITS, and STOP BITS fields change

to the settings appropriate for the specific device.

NOTE: “KBD300” is used to refer to the KBD100, KBD200A, and KBD300A keyboards.

3. Optional: Some device options allow a choice of communication type, baud rate, and/or parity rate. If this is the case, select the

desired settings.

4. Optional: If you select an ASCII device you can select ON in the Report Alarm field to set the CM6800 to report alarms to that device.

The CM6800 reports the following alarm information:

Action

ASCII text

#Ea

An alarm is triggered

An alarm is cleared

An alarm is acknowledged

#Ia

#Ka

NOTE: The CM6800-32X6 reports the physcial alarm number. If you use the eight internal alarm inputs on the rear panel, do not use

the first eight inputs on any external alarm interface units (ALM2064), or you will have a numbering conflict.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRIORITY

The CM6800 provides eight levels of priority control. Each level defines the ability of a keyboard to control a pan/tilt/zoom (camera

positioning system) and to access programming screens.

Priority level applies system wide; a keyboard assigned priority level 2 on COM port 5 has a higher priority than a keyboard assigned priority level

4 on COM port 4. A higher level keyboard takes precedence over a lower level keyboard when the keyboards are issuing control commands.

PELCO SWITCHER

KEYBOARD PRIORITY MENU

MODEL CM6800

MAIN MENU

PORT 05

CAMERA

KBD

PRIORITY

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

RETURN

ENGLISH

RETURN

00658

00654

Figure 42. Access the Priority Screen

PORT:

Select the COM port number for which you are programming priority control.

PRIORITY:

For each keyboard connected to the specified port, assign a priority level (01-08).

OPTIONS:

Level 1 = highest priority

Level 8 = lowest priority

Levels 1 - 3 have the ability to access programming screens. Levels 4-8 cannot access programming screens. The lowest

level or keyboards located at the same level will access devices on first-come, first-served basis.

NOTE: If you connect an ASCII keyboard/device to the CM6800 (COM port 1, 2, or 4), you can connect only one keyboard to a port. For

ASCII keyboards, priority control is based on the entry for keyboard 1.

SEQUENCE

The CM6800 provides two types of sequences:

•

An operator can program a scratchpad sequence from an individual monitor, without accessing password-protected programming

screens.

•

System sequences are password-protected and can run on any system monitor.

PELCO SWITCHER

MODEL CM6800

MAIN MENU

SEQUENCE 01

STP CAM DWL CMD

HELP

AUX

CON

000

0001

0002

0003

0004

0005

0006

PATT

PRES

SSCN

FSCN

PRES

CAMERA

— — — —000

COFF 000

— — — —000

LOGICAL CAMERA

MONITOR

ACCESS

— — — — 00

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

ENGLISH

RETURN

00660

00654

Figure 43. Sequence Screen

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

SCRATCHPAD SEQUENCE MON ##

STP CAM

DWL

CMD

PATT

PRES

FSCN

RSCN

SSCN

— — — — 00

AUX

CON

001

0001

0005

0008

0012

0023

0006

0007

0008

0009

0010

0011

0012

0013

0014

0015

0016

0017

0018

GOFF 101

PELCO VIDEO SWITCHER

MODEL CM6800

CON

008

— — — —000

PASSWORD TO MAIN MENU

*******

SCRATCHPAD SEQUENCE

MACRO STATUS VIEW

RETURN

HELP

20019

RETURN

00659

Figure 44. Scratchpad Sequence Screen

SEQUENCE:

STP:

Select the sequence number you want to program.

Each sequence can include up to 72 steps. For each step select entries for the following fields as necessary:

CAM:

DWL:

Enter the desired camera number (logical number).

Enter the dwell time (01-99 seconds).

CMD and ##: Select a command; if you select a pattern or a preset enter a valid pattern or preset number.

OPTIONS:

PATT = pattern

PRES = preset

RSCN = random scan

FSCN = frame scan

SSCN = stop scan

AUX and ##:

Select an auxiliary to be activated.

Global = internal and external auxiliaries.

OPTIONS:

GON = turn global auxiliary on

GOFF = turn global auxiliary off

CON = turn camera auxiliary on

COFF = turn camera auxiliary off

NOTE: Activate the auxiliaries on the rear panel of the CM6800 by selecting global auxiliary numbers 1 or 2. The remaining global

auxiliary numbers control REL2064 Relay Interface Unit auxiliaries.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

TIME AND DATE

Use the Time and Date screen to set the system time and date settings. The time and date displayed on the monitor during real-time

camera display is the time set in the memory through this screen. The system time and date information is kept current in battery-backed

RAM. New time and date information will be set when you apply the changes (refer to the SET TIME & DATE field description).

PELCO SWITCHER

SET TIME & DATE

MODEL CM6800

MAIN MENU

SET

MM DD YY

01 / 01 / 01

01 : 01 : 01

CAMERA

DATE:

TIME:

LOGICAL CAMERA

MONITOR

ACCESS

TIME & DATE

PORT

PRIORITY

SEQUENCE

MACRO

DISPLAY AS

FORMAT: DD/MMM/YY

STYLE: 24Hr

10 ALARM CONTACTS

11 EVENT TIMER

12 SET AUXILIARY

13 SET PASSWORD

14 ABOUT CM6800

SET TIME & DATE

RETURN

ENGLISH

RETURN

00662

00654

Figure 45. Access the Time and Date Screen

1. Select or enter the month, day, and year of the desired system date.

2. Select or enter the hour, minute, and second of the desired system time.

3. Select the on-screen date format.

OPTIONS:

DD/MMM/YY

MMM/DD/YY

YY/MMM/DD

DD/MM/YY

MM/DD/YY

YY/MM/DD

4. Select the on-screen time format. This setting affects the on-screen time displayed on system monitors only. System functions

programmed through the event timers (refer to Event Timers in this section) are based on 24-hour time settings.

OPTIONS:

24Hr

AM/PM (12 Hr)

5. Navigate left or right in the SET TIME & DATE field to apply the changes.

PATTERNS, PRESETS, AND ZONES

Special characters added through the CM6800-MGR may not be available with your camera positioning system. Preset, pattern, and zone

labels containing special characters will appear on the monitor with blanks in place of the special characters.

Refer to the Operation section for instructions on creating patterns. Refer to your keyboard manual for instructions on programming

presets and zones.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

OVERVIEW

A brief description of CM6800 operation is provided here. Refer to the following sections for detailed instructions and options.

Install the CM6800E and connect

Refer to the Installation section.

all system devices.

Power-up the system.

Switch monitor.

Refer to the System Start-up section.

1. Enter the monitor number.

2. Press the MON key.

Select camera.

1. Enter the camera number.

2. Press the CAM key.

Control PTZ receivers.

Use the appropriate PTZ control keys or joystick (depending on the keyboard used).

Extended Coaxitron protocol receivers can be operated without any programming changes. Other

receiver control protocols require programming changes.

Call a preset.

Program the preset through the keyboard.

1. Enter the preset number.

2. Press the PRESET key or Prst/Lock key (depending on the keyboard used).

Refer to the Troubleshooting section.

System does not function.

OPERATING THE CM6800

The CM6800 can be operated with a KBD100, KBD200A, KBD300A, KBD960, or KBR960 keyboard. Operation instructions are provided

below, but you should become familiar with the detailed instructions provided in the appropriate keyboard manual.

The CM6800 can also be controlled with ASCII commands. Refer to the ASCII Operating Commands section.

SWITCH MONITORS

If you select a restricted monitor, the monitor does not switch; the keyboard LED displays the previously selected monitor number.

ALL KEYBOARDS

1. Enter the monitor number.

2. Press the MON key. The keyboard LED displays the selected monitor number.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

SELECT CAMERAS

If you select a restricted camera view, the camera view does not appear on that monitor. The previously selected, unrestricted camera

view remains on the monitor.

KBD100/200A/300A KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the camera number.

2. Press the CAM key.

1. Enter the camera number.

2. Press the CAM key.

Press the BWD or FWD key to scroll through the available cameras. Press the PREV or NEXT key to scroll through the available cameras.

From the Camera Menu, select

available cameras.

to scroll through the

CONTROL RECEIVERS

Select a suitable camera and operate a PTZ function. A keyboard with “view-only” access can view the signal from the specified camera

but cannot control the camera.

Extended Coaxitron protocol receivers can be operated without any programming changes. Other receiver control protocols require

programming changes. Refer to the Programming section.

Receiver control is not available with the KBD100 keyboard.

KBD200A KEYBOARD

Lens Control: Focus, Iris

Pan/Tilt/Zoom

Press and hold the appropriate lens control key until the desired

effect is seen.

Press and hold the appropriate pan/tilt key until the camera

reaches the desired position. To change the speed of movement,

press a number (1-9) key first (1=slowest, 9=fastest). Press and

hold the appropriate zoom key until the desired effect is seen.

KBD300A KEYBOARD

Pan/Tilt/Zoom

Lens Control: Focus, Iris

Press and hold the appropriate lens control key until the desired

effect is seen.

Move the joystick until the camera reaches the desired position.

To increase the speed of movement, move the joystick farther

from center.

Twist the joystick clockwise to zoom in, counterclockwise to

zoom out.

KBD960/KBR960 KEYBOARDS

Pan/Tilt/Zoom

Lens Control: Focus, Iris

Use the NEAR/FAR key to focus near or far.

Move the joystick until the camera reaches the desired position.

To increase the speed of movement, move the joystick farther

from center or press the T key to pan at turbo speed.

Use the OPEN/CLS key to open or close the iris.

Twist the joystick clockwise to zoom in, counterclockwise to

zoom out. Or use the IN/OUT key to zoom in or out.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATE SEQUENCES

You can run a scratchpad sequence from an individual monitor or a system sequence on any monitor accessible from the keyboard. When

running a sequence, any cameras not accessible to the keyboard will be bypassed.

A sequence runs continuously until a system operator selects a different camera, or an event timer starts another sequence or macro.

KBD100/200A/300A KEYBOARDS

Run a Sequence

KBD960/KBR960 KEYBOARDS

Run a Sequence

1. Enter a sequence number (1-32). Skip this step to run a

scratchpad sequence.

1. Select

2. Enter a sequence number (1-32 for a system sequence; 0 for the

scratchpad sequence).

2. Press and hold the NEXT or PREV key to move forward or

backward through the sequence.

SEQ

3. Select

to start the sequence.

To move through the sequence one camera at a time:

Press the NEXT key to move forward.

Press the PREV key to move backward.

1. Select

2. Select

SEQ

Pause a Sequence

to enter the Sequence Menu.

3. Enter a sequence number (1-32).

1. Press the HOLD key; monitor displays H.

2. Press the HOLD key to resume.

Stop a Sequence

Select

to scroll through available sequences.

to start the sequence.

4. Select

1. Enter a camera number.

2. Press the CAM key.

NOTE: You can define a function key to run a sequence. Refer to the

KBD960 Keyboard Installation/Operation Manual for instructions.

Pause a Sequence

1. Select

2. Select

to resume.

Stop a Sequence

1. Select

1. Enter a camera number.

2. Press the CAM key.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

RUN A MACRO

A macro runs until the last step is completed (unless you specify a loop in the macro).

KBD100/200A/300A KEYBOARDS

Run a Macro

KBD960/KBR960 KEYBOARDS

Run a Macro

1. Enter the macro number.

2. Press the MACRO key.

1. Select

2. Enter a macro number.

MAC

3. Select

to start the macro.

Stop a Macro

1. Enter the number of the running macro.

2. Press the MACRO key.

1. Select

2. Select

MAC

NOTE: Any macro or sequence started

by this macro will continue to run.

to enter the Macro Menu.

3. Enter a macro number.

Select

to scroll through available macros.

to start the macro.

4. Select

NOTE: You can define a function key to run a macro. Refer to the KBD960 Keyboard

Installation/Operation Manual for instructions.

Pause a Macro

1. Select

2. Select

to resume.

Stop a Macro

1. Select

1. Enter a camera number.

2. Press the CAM key.

ACKNOWLEDGE AN ALARM

When an alarm is triggered, an alarm icon appears on the monitors programmed to show that alarm.

KBD100/200A/300A KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the monitor number.

2. Press the MON key.

3. Press the ACK key. The alarm is

removed from the selected monitor.

1. Select

2. Select

to reset the alarm on the individual monitor.

4. Repeat for each alarm.

Select

to reset the alarm on all monitors.

You can also select

to mute the alarm.

NOTE: You can define a function key to acknowledge an alarm. Refer to the KBD960

Keyboard Installation/Operation Manual for instructions.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CALL A PRESET

Program the preset through the keyboard. Refer to the appropriate keyboard manual for instructions. Presets are not available with the

KBD100 keyboard.

KBD200A/300A KEYBOARDS

KBD960/KBR960 KEYBOARDS

1. Enter the preset number.

2. Press the PRESET key.

1. Enter the preset number.

2. Press the Prst/Lock key.

Select the PRST icon.

CREATE AND RUN A PATTERN

Patterns are not available with the KBD100 keyboard.

KBD960/KBR960 KEYBOARDS

KBD200A/300A KEYBOARDS

Create a Long Pattern

Refer to the KBD960 Keyboard Installation/Operation manual

for instructions on creating a pattern.

1. Enter a camera number.

PRST

1. Select

2. Select

to display the Preset Menu.

to start a pattern.

2. Enter 0.

3. Press and hold the PATTERN key for two seconds.

4. The monitor will indicate the programming function is active.

Move the camera position as desired for the pattern.

PRST

1. Select

to display the Preset Menu.

5. Press the ACK key to close the programming function.

2. Enter 1.

Create a Short Pattern

3. Select

to run the first pattern of previously defined

1. Enter a camera number.

half-patterns.

2. Enter the short pattern number (1 or 2).

3. Press and hold the PATTERN key for two seconds.

PRST

1. Select

to display the Preset Menu.

4. The monitor will indicate the programming function is active.

Move the camera position as desired for the pattern.

2. Enter 2.

3. Select

to run the second pattern of previously defined

5. Press the ACK key to close the programming function.

half-patterns.

Run a Long Pattern

1. Press the PATTERN key.

2. Move the joystick or call a preset to stop the pattern.

Run a Short Pattern

1. Enter the short pattern number (1 or 2).

2. Press the PATTERN key.

3. Move the joystick or call a preset to stop the pattern.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATE AUXILIARIES/RELAYS

Local auxiliaries are the outputs on the rear panel of the CM6800. External auxiliaries are available by connecting an REL2064 Relay

Interface Unit to the CM6800 through COM port 3.

Operate a Local Auxiliary

KBD100/200A/300A KEYBOARDS

KBD960/KBR960 KEYBOARDS

Auxiliary 1 relay: Press F1 to activate/deactivate.

Auxiliary 1 relay: Press F12* to activate/deactivate.

Auxiliary 2 TTL output: Press F2 to activate/deactivate.

Auxiliary 2 TTL output: Press F24* to activate/deactivate.

* F12 and F24 are the default auxiliary control function keys; user-

selected function keys can be defined through the Key Define

Menu. Refer to the KBD960 Keyboard Installation/Operation

Manual for instructions.

NOTE: If you connect REL2064 Relay Interface Units (up to two) to

the CM6800E, operation of the two relays on the rear panel of the

CM6800E-32X6 will also operate the first two relays on the first

external unit (unless you number the external relays starting at 64).

Operate an External Auxiliary

The CM6800 can control up to two REL2064 Relay Interface Units connected to the system. Each unit provides 64 relays. Refer to the

REL2064 Relay Interface Unit Installation/Operation Manual for detailed information. External relays cannot be operated with the KBD100.

KBD200A/300A KEYBOARDS

KBD960/KBR960 KEYBOARDS

The KBD200A/300A keyboards (firmware version 4.2 and

later) can operate external relays.

1. Enter the GPI number for the appropriate relay output.

GPI

2. Press

Refer to the KBD200A Keyboard Installation/Operation

Manual or the KBD300A Keyboard Installation/Operation

Manual for instructions.

3. Press the desired AUX number icon to activate the relay and

associated peripheral device.

(Press

to access AUX 5-8.)

NOTE: External relays cannot be operated with KBD200A/

300A keyboard firmware versions prior to 4.2.

MTRY

4. If

is highlighted, the operation is momentary. If

is not

highlighted, the operation is latching. Refer to the KBD960

Keyboard Installation/Operation Manual for instructions.

Operate an Auxiliary in a Receiver

Receiver auxiliary control is not available with the KBD100.

KBD200A/300A KEYBOARDS

Press AUX ON/F4 to activate.

Press AUX OFF/F5 to deactivate.

KBD960/KBR960 KEYBOARDS

From the Camera Menu, press

, and then release to control an

AUX 1 momentary function on the selected camera.

Press

to control an AUX 2 momentary function. Press

through

access

To control a momentary function:

1. Enter the auxiliary number.

2. Press and hold AUX ON/F4, and then release.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONTROL GENEX MULTIPLEXER AND GENEX MULTIPLEXER DISPLAYS

Multiplexer control is not available with the KBD100.

KBD960/KBR960 KEYBOARDS

1. Enter a MUX input number and press

KBD200A/300A KEYBOARDS

1. Enter the number of the multiplexer input.

2. Press the CAM key.

. Each MUX

input is associated with a camera input. Figure 43

shows MUX 1 being controlled.

3. Press the SHIFT key. When the SHIFT LED is lit, the keyboard can

be used to operate the following Genex multiplexer function keys:

MUX

2. Select ^MUX. MUX Menu 1 appears.

should be

highlighted, which means you have MUX control.

F1: Digital zoom

F2: PIP display

F3: Quad display

3. Cycle through the 16 picture inserts (if yo have a

16-channel multiplexer) by entering the camera number

AUX ON/F4: 9-screen display

AUX OFF/F5: 16-screen display

and selecting

4. Select again to zoom into the MUX camera. You

To select a camera through the multiplexer:

can move the joystick to view a specific area.

a. Enter the desired camera number (1-16, based on the camera

assignments set through the multiplexer).

5. Select

to bring up MUX Menu 2. The icons for a

picture-in-picture display, 4-camera display, 9-camera

display, and 16-camera display appear.

b. Press the CAM key.

4. Press the SHIFT key to return to normal keyboard operation.

6. Select

to view four of the available 16 cameras on

When the SHIFT LED is off, you can control the currently selected

PTZ camera through the multiplexer.

one monitor. You can cycle through all 16 cameras, four

at a time, by repeatedly selecting

To return to camera selection controlled by the CM6800E:

7. Select to view nine of the available 16 cameras on

a. Select the desired camera number.

b. Press the CAM key.

c. Move the joystick as necessary.

one monitor. Select again to see the remaining seven

cameras.

8. Select

to view all 16 available cameras on one

monitor.

Note that

does not work on a 9-channel

mulitplexer.

OPERATE SCANNING FUNCTIONS

Operation of the scanning functions depends on the kind of receiver or pan/tilt mechanism you have. Refer to the appropriate keyboard

manual for detailed instructions on operating scanning functions.

DETECT VIDEO LOSS

The CM6800 detects video loss from any system camera. If video is lost from a camera, the CM6800 blue screen appears on any monitor

viewing that camera. When video is restored to that camera, the camera view appears on the monitor(s) again. If the system is pro-

grammed for a video loss alarm, the alarm icon appears.

DEFINE ZONES

A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is associated. When the associated camera is

panned through or remains within this defined zone the zone label appears on the monitor.

Refer to the appropriate keyboard manual for detailed instructions on defining zones.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

CM6800 DIP SWITCHES

Figure 46. CM6800 DIP Switches – Factory Default Settings

Table G. CM6800 DIP Switch Settings

CM6800 DIP Switch

Default Settings

Switch 1 OFF (0) = NTSC

ON (1) = PAL

CM6800-32X6: OFF

CM6800-32X6-X: ON

Switch 2 RESERVED – must be in the OFF position for proper operation

OFF

Switch 3 RESERVED – must be in the OFF position for proper operation

Switch 4 RESERVED – must be in the ON position for proper operation

Switch 5 RESERVED – must be in the OFF position for proper operation

Switch 6 RESERVED – must be in the OFF position for proper operation

Switch 7 USED TO RESET SOFTWARE. REFER TO THE SOFTWARE

RESET SECTION

CAUTION: Resetting the software restores the system software to original

settings, programmed by Pelco. All user programming is lost.

Switch 8 RESERVED – must be in the OFF position for proper operation

OFF

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARM GROUP DISPLAY OPTIONS

To display on a monitor, an alarm must be assigned to an alarm group (A-F). Before programming alarms you may want to determine the

alarm display format for each alarm group. An alarm can include up to eight steps, so eight camera views could display as a part of each

alarm.

A priority alarm appears on system monitors before non-priority alarms, despite the order specified by the alarm group assignment. In the

following examples, all alarms are at the same priority level. Refer to the PRIORITY description in Program Internal and External Alarms.

Block Build

Alarmed cameras are displayed across a block of alarm monitors in a sequential order. All steps programmed for the alarm contact appear

on the designated monitor.

Example: Seven alarms set to display on monitors 02-06 will appear in the following order:

1st Display

Cycle

Next Display

Cycle

Acknowledging

Alarms 1 & 2

Next Display

Cycle

ALARM MONITOR GROUP SETUP

Monitor

MON

02 B

1st alarm

1st and 7th

alarms cycle

2nd and 8th

alarms cycle

Acknowledge

1st alarm

Acknowledge

2nd alarm

7th alarm

—

03 B

2nd alarm

8th alarm

04 B

05 B

06 B

07 B

3rd alarm

4th alarm

5th alarm

6th alarm

3rd alarm

4th alarm

5th alarm

6th alarm

3rd alarm

4th alarm

5th alarm

6th alarm

3rd alarm

4th alarm

5th alarm

6th alarm

HELP

00638

New alarms display on the lowest monitor number with the fewest alarms cycling.

Chronological Pair: D and Q

The oldest alarm of a specific group is displayed on one designated monitor, while all other alarms in the group are sequenced on the

second designated monitor. All steps programmed for the alarm contact appear on the designated monitor.

Example: Four alarms set to display on monitors 04 and 05 will appear in the following order:

Monitor

1 Alarm

2 Alarms

3 Alarms

4 Alarms

ALARM MONITOR GROUP SETUP

04 D

05 Q

1st alarm

2nd alarm

1st alarm

2nd and 3rd

alarms cycle

1st alarm

2nd, 3rd, and 4th

alarms cycle

MON

—

You must acknowledge alarms in a chronological pair from the display monitor (D).

Then the next oldest alarm moves to the display monitor and the remaining alarms

continue to cycle through the queue monitor (Q). This format requires you to acknowl-

edge each alarm in the order in which they occur.

HELP

00640

Acknowledging alarms in this example:

Monitor

1st Cycle

Next Cycle

04 D

Acknowledge

1st alarm

Acknowledge

2nd alarm

Acknowledge

3rd alarm

Acknowledge

4th alarm

05 Q

2nd, 3rd, and 4th

alarms cycle

3rd and 4th

alarms cycle

4th alarm

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Reverse Chronological Pair: M and L

The most recent alarm of a specific group is displayed on one designated monitor, while all other alarms in the group are sequenced on

the second designated monitor. All steps programmed for the alarm contact appear on the designated monitor.

Example: Four alarms set to display on monitors 04 and 05 will appear in the following order:

Monitor

06 M

1 Alarm

2 Alarms

2nd alarm

1st alarm

3 Alarms

4 Alarms

ALARM MONITOR GROUP SETUP

MON

1st alarm

3rd alarm

4th alarm

—

07 L

1st and 2nd

alarms cycle

1st, 2nd, and 3rd

alarms cycle

—

You must acknowledge alarms in a reverse chronological pair from the display

monitor (M). Then the next most recent alarm moves to the display monitor and the

remaining alarms continue to cycle through the queue monitor (L). This format

requires you to acknowledge each alarm in the reverse order from which they

occurred.

HELP

00641

Acknowledging alarms in this example:

Monitor

1st Cycle

Next Cycle

06 M

Acknowledge

Alarm 4

Acknowledge

Alarm 3

Acknowledge

Alarm 2

Acknowledge

Alarm 1

07 L

Alarms 1, 2,

and 3 cycle

Alarms 1

and 2 cycle

Alarm 1

Salvo Group

Multiple camera views within the alarm contact programming (the “steps”) are displayed simultaneously as a group across a set of

monitors. When a new alarm triggers, all monitors switch to the new alarm at the same time.

When programming a Salvo Group:

•

Program the Salvo Group to display across a number of monitors equal to the number of steps in the alarm contact(s); for example if

the alarm contact has six steps, set the Salvo Group to display on six monitors. If an alarm contact contains more steps than

monitors defined for the Salvo Group, the additional steps do not appear on a monitor during the alarm.

Each alarm contact assigned to the Salvo Group should contain the same number of steps.

•

The Salvo Group switches based on the dwell time entered for the first step in the alarm contact.

Example: Two alarm contacts with three steps set to display on three monitors will appear as follows:

Monitor

06 S

1 Alarm

2 Alarms

Next Display Cycle

1st alarm, step 1

1st alarm, step 2

1st alarm, step 3

After Acknowledging 1st Alarm

2nd alarm, step 1

1st alarm, step 1

1st alarm, step 2

1st alarm, step 3

2nd alarm, step 1

2nd alarm, step 2

2nd alarm, step 3

07 S

2nd alarm, step 2

08 S

2nd alarm, step 3

ALARM MONITOR GROUP SETUP

MON

—

HELP

00639

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

MACRO COMMANDS

Table H provides a description of each macro command and the additional fields required for each command. Refer to the Macro section

for instructions on programming macros.

Table H. Macro Commands

Command Description

Specify

Auxiliary

Field(s)

GON

GOFF

Activate an auxiliary.

Turn off an auxiliary.

Command #

Auxiliary Notes:

• “Global” includes both internal and external auxiliaries.

• Auxiliaries on the rear panel of the CM6800 Matrix Switcher are activated by global auxiliary numbers 1 and 2.

CON

Activate a camera auxiliary.

Camera auxiliary

Camera

Command #

Camera

Monitor

COFF

Turn off a camera auxiliary.

Camera auxiliary

Camera

Command #

Camera

Monitor

SEQ

Start a sequence. A sequence runs continuously until a system operator selects Sequence

Command #

Monitor

a different camera, or an event timer starts another sequence or macro.

Monitor

SWT

COPY

Switch a camera to a monitor.

Camera

Monitor

Copy a camera view to a monitor.

Monitor to copy from

Monitor to copy to

Step

Command #

Monitor

GO TO

LOOP

Go to step number specified.

Loop a macro.

Command #

0 = loop continuously

1-999 = loop the specified

number of times

Local auxiliary

?AUX

?ALM

?SW

Check a local auxiliary; if the auxiliary is active, the next step is executed; if

the auxiliary is not active, the next step is skipped.

Command #

Check an internal alarm; if the alarm is active, the next step is executed; if

not, the next step is skipped.

Alarm

Check whether a camera is displayed on a monitor; if it is, the next step is

executed; if not, the next step is skipped.

Camera

Monitor

Macro

Camera

Monitor

Command #

None

STPM

END

Stop a macro.

Exit the macro; no further steps are executed. Any macro or sequence started None

by this macro will continue to run.

DON

Displays on-screen text on the specified monitor.

Removes on-screen text from the specified monitor.

Switch a camera connected through the multiplexer.

Monitor

DOFF

MSWT

Monitor

Camera to switch^◆

Multiplexer input

Monitor

Command #

Camera

Monitor

PIPB

PIPF

Display multiplexer picture-in-picture view with the

designated camera in the background.

Background camera^◆

Multiplexer input

Monitor

Foreground camera^◆

Multiplexer input

Monitor

Command #

Camera

Monitor

Display multiplexer picture-in-picture view with the

designated camera in the foreground.

Command #

Camera

Monitor

^◆For multiplexer functions, the camera number is the number of the video input on the multiplexer. The multiplexer input number is the number

of the video input on the rear panel of the CM6800.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table H. Macro Commands (Continued)

Specify

Command Description

Field(s)

PIPO

Turn off multiplexer picture-in-picture view.

Multiplexer input

Monitor

Camera

Monitor

QUAD

Display multiplexer four-camera mode.

Display multiplexer nine-camera mode.

Camera group*

Multiplexer input

Monitor

Command #

Camera

Monitor

NANO

Camera group*

Multiplexer input

Monitor

Command #

Camera

Monitor

HEX

Display multiplexer sixteen-camera mode.

Zoom multiplexer camera view.

Multiplexer input

Monitor

Camera

Monitor

ZOOM

1 = zoom once

2 = zoom twice

Command #

Multiplexer input

Monitor

Camera

Monitor

AAI

Arm internal alarm.

Internal alarm

External alarm

Physical camera number

Command #

DAI

Disarm internal alarm.

AAE

DAE

AAV

Arm external alarm.

Disarm external alarm.

Arm video loss detection for a camera.

Logical camera number

Physical camera number

Camera

DAV

Disarm video loss detection for a camera.

Command #

Logical camera number

Macro

Camera

MACR

PATT

Start a specific macro. A macro runs until the last step is completed (unless

you specify a loop in the macro).

Command #

Start a pattern.

Pattern**

Camera

Monitor

Preset**

Camera

Monitor

Camera

Monitor

Camera

Monitor

Camera

Monitor

Command #

Camera

Monitor

Command #

Camera

PRES

Start a preset.

Monitor

Camera

RSCN

FSCN

SSCN

Start a random scan.

Start a frame scan.

Stop a scan.

Monitor

Camera

Monitor

Camera

Monitor

* Refer to the MX4000 Genex Series Simplex and Duplex Multiplexers Installation/Operation Manual for information on multiple

camera displays.

** The number of patterns and presets available is determined by the camera positioning system. Refer to the appropriate camera

positioning system manual.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

ASCII OPERATING COMMANDS

ASCII protocol uses the ASCII character set to transmit and receive commands between an ASCII device (such as a personal computer (PC)

or ASCII keyboard) and the CM6800.

The ASCII protocol communicates in a standard asynchronous, byte-oriented protocol that includes: 1 start bit, 8 data bits, 1 parity bit (odd

parity), and 1 stop bit. The default communication rate is 9600 baud.

A lowercase “a” ends each command. The ASCII translator acknowledges accepted commands and rejected commands with the following

responses:

AKa

NAa

command accepted

command rejected or the ASCII translator does not recognize the command

If the command requires a numeric value, enter the number first.

Table I provides examples of ASCII commands. Table J lists all of the commands.

Table I. Examples of ASCII Commands

Functional Procedure

Commands

Result

Select a pan and tilt device labeled “CAMERA # 16”

and switch it to monitor # 3.

3Ma16#a

Switch camera 16 to currently selected monitor 3.

Manipulate the pan and tilt device.

1Ma3#a

Switch camera 3 to monitor 1.

5Ma2#a3\a

47Ra33Da

Go to camera 2, preset 3, on monitor 5.

Pan right at speed 47, tilt down at speed 33.

Stop all image motion.

Switch a camera.

Call a preset.

Pan and tilt.

1Ma3#a

5Ma2#a3\a

47Ra33Da

Switch camera 3 to monitor 1.

Go to camera 2, preset 3, on monitor 5.

Pan right at speed 47, tilt down at speed 33.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table J. ASCII Commands

Number ranges are enclosed in brackets – do not enter the brackets. When you control a fixed speed pan and tilt, omit the speed information.

NOTE: In a 96 x 16 system the numbers for cameras, monitors, alarms, and relays can be doubled.

Desired Action

Command

Result

Select monitor

[1-9999]Ma

Calls a monitor to use for camera operation.

Select camera

Next camera

Previous camera

[1-9999]#a

-a

Selects a camera to display on the current operating monitor. The NEXT key (+) and

PREV key (-) commands switch to the next numbered camera in the system.

Start a sequence forward

[1-99]qa

Starts the selected sequence going forward (incrementing camera numbers).

Starts the selected sequence going backward (decrementing camera numbers).

Start a sequence backward [1-99]ba

Hold a sequence

Places the running sequence on hold, freezing the currently selected camera on the

monitor. It lets you control the camera or switch. The sequence is still “armed” on

the monitor, but inactive.

Hold a macro

[1-64]ea

Places the running macro on hold.

Pan left

Pan right

Stop pan left

Stop pan right

[1-64]La

[1-64]Ra

~La

Moves the currently selected pan and tilt device left or right at the speed

indicated. If you omit the speed, some devices move at their default speed and

others move at their slowest possible speed. Speed information has no effect on

fixed speed devices.

~Ra

Tilt up

[1-63]Ua

[1-63]Da

~Ua

Moves the currently selected pan and tilt device up or down at the speed

indicated. If you omit the speed, some devices move at their default speed and

others move at their slowest possible speed. Speed information has no effect on

fixed speed devices.

Tilt down

Stop tilt up

Stop tilt down

~Da

Zoom telephoto

Zoom wide

Stop zoom telephoto

Stop zoom wide

Makes the currently selected camera zoom in (close up view) or zoom out (wide

view).

~Ta

~Wa

Focus near

Focus far

Changes the good focus range nearer or farther on the currently selected camera.

Stop focus near

Stop focus far

~Na

~Fa

Iris open

Iris close

Opens (brighter image) or closes (darker image) the iris on the currently selected

camera.

Stop iris open

Stop iris close

~Oa

~Ca

Stop all PTZ motion

Stops all image motion (stops pan, tilt, zoom, focus, and iris). Does not stop a

pattern.

Record pattern

Execute pattern

End pattern

[1-99]/a

[1-99]pa

[1-99]na

On receivers that do patterns, these commands let you record your motions and

operations (for a limited time) and then have the system repeat them.

Go to preset position

Set preset with a label

[1-99]\a

Recalls a stored preset position.

la[string]!a

[1-9999]^a

Sets a preset location with an embedded label, where the ASCII string must be

UPPERCASE characters.

The [string] is an alphanumeric label up to 20 characters long and [1-9999] is the

associated preset number.

NOTE: All transmitted characters must be ASCII.

Sets a preset location without an embedded label.

Begins a zone without a label.

Set preset without a label

Begin zone

[1-9999]-^a

[1-8](a

Begin zone with a label

la[string]!a[1-8](a Begins a zone with an embedded label. The ASCII string must be uppercase

characters.

End zone

[1-8])a

Ends the zone program

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table J. ASCII Commands (Continued)

Desired Action

Command

Result

Begin random scan

Begin frame scan

Stop scan

1@a

2@a

~@a

These commands start and stop scans.

Auxiliary on

Auxiliary off

[1-256]xa

[1-256]~xa

Auxiliaries are relay outputs that can be controlled through the protocol. 1-2

operate the AUX 1 and F2 auxiliaries on the rear panel of the CM6800 (and the

first two auxiliaries on an external REL2064). 3-128 operate the external

auxiliaries on up to two REL2064 Relay Interface Units.

Camera auxiliary on

Camera auxiliary off

[1-8]Aa

[1-8]Ba

Operates auxiliaries at the camera (receiver).

Start macro

[1-64]Sa

[1-64]Ha

[1-9999]Ia

Starts the selected macro.

Stop macro

Stops the selected macro.

Acknowledge alarm

Acknowledges an existing alarm.

These commands arm and disarm system alarms.

Arm internal alarm

[1-8]Jia

Arm external alarm

[1-256]Jea

[1-48]Jva

[1-8]~Jia

[1-256]~Jea

[1-48]~Jva

Arm video loss alarm

Disarm internal alarm

Disarm external alarm

Disarm video loss alarm

Trigger an alarm

Clear an alarm

#Ea

#Ia

An ASCII device can send these commands through the CM6800 to control

alarms in an external alarm device, such as an ALM2064 Alarm Interface Unit.

Acknowledge an alarm

#Ka

NOTE: These commands do not affect internal alarms on the CM6800 rear

panel.

An alarm is triggered

An alarm is cleared

An alarm is acknowledged

#Ea

#Ia

#Ka

If you configure a CM6800 Port to report alarms to an ASCII device, the CM6800

reports the alarm information using these commands.

NOTE: The CM6800-32X6 reports the physical alarm number. If you use the

eight internal alarm inputs on the rear panel, do not use the first eight inputs on

any external alarm interface units (ALM2064), or you will have a numbering

conflict.

Select a MUX camera

Display picture-in-picture view

Display four-camera mode

Display nine-camera mode

Display 16-camera mode

Digital mode zoom

Digital mode pan left

Digital mode pan right

Digital mode tilt up

[1-9999]#m

These commands control a Genex multiplexer connected to the CM6800.

dLm

dRm

dUm

dDm

Digital mode tilt down

Send camera title

[1-48]Ya[string]!a

Sends a camera title to the matrix switching system. You can only send one

camera title at a time.

Valid characters in the string are A-Z, a-z, space, and 0-9 in ASCII representa-

tion. Strings are limited to 20 characters.

Version

Returns the version number of the device.

Set date and time

ZaMM/DD/YY/HH:

MM:Ssa

Sets the date and time. Since the date and time string could be confused with

other commands, the command Za comes first. This puts the receiving device

into a mode that can accept the specialized string.

NOTE: All transmitted characters must be ASCII.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

GAINING INITIAL CONTROL

If you are having problems gaining control of your system for the first time:

•

Confirm that all system equipment is plugged in and has power.

Confirm that each keyboard and peripheral device in your system has a unique local address. Refer to the Switch Settings section in

the appropriate keyboard manual.

•

Be sure data cables have not been mixed up.

Cycle the data cable to the keyboard:

1. Unplug the data cable from the rear of the keyboard.

2. Plug the data cable back into the rear of the keyboard.

3. WAIT AT LEAST FIVE SECONDS.

4. Select a monitor.

If you still cannot gain control of the system:

•

Confirm the wiring is correct and the user-supplied cable between wall jacks is appropriate for the application.

Confirm that when the keyboard data cable is cycled, the keyboard LED flashes momentarily (indicating power).

If you still cannot gain control of the system, call Pelco’s 24-hour technical support at 1-800-289-9100 or 1-559-292-1981.

NOTE: There are no userserviceable parts inside the CM6800. Only authorized service personnel may open the unit.

SOFTWARE RESET

Pelco strongly recommends uploading system settings to the CM6800-MGR before the software reset – this will allow you to restore

system settings after the software reset.

CAUTION: Resetting the software restores the system to default settings.

ALARM

COM

PTZ

CONTROL

1. Remove the two screws and the DIP switch cover plate from the rear of the

matrix switcher.

COM

2. Move DIP switch 7 to the ON position (to “0”).

3. Cycle power.

120/230V~

50/60 HZ

25 WATTS

VIDEO OUTPUTS

The switcher will go through a software clear cycle and reset to factory

defaults.

DIP SWITCH COVER PLATE

Figure 47. Dip Switch Cover Plate

4. Move DIP switch 7 to the OFF position.

Failure to move DIP switch 7 to the OFF position could result in loss of system

settings during a power outage.

5. Re-initialize keyboards by entering the monitor number and then pressing the

MON key.

SWITCH 7:

ON = SOFTWARE RESET

OFF = NORMAL SYSTEM

OPERATION

6. Download your previous system settings (revise settings as necessary) from

the CM6800-MGR.

Figure 48. CM6800 DIP Switch 7

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

SOLUTIONS TO COMMON PROBLEMS

Refer to Table K for a list of common problems and their solutions.

Table K. Solutions To Common Problems

Problem

Remedy

CM6800 does not have power.

Make sure the power cord is plugged in.

You can see some cameras and not others

from your location.

Confirm that the camera is properly connected and has power.

The keyboard and monitor may have been denied access to the cameras.

The CM6800 does not respond to keyboard

commands.

Confirm that the monitor the keyboard is addressing is the same as the monitor in

front of you.

Access to that monitor may be restricted from that keyboard. Select another monitor.

Pressing the PGM key displays a P on the

keyboard LED, but the Password menu

does not appear on the monitor.

Confirm that the keyboard transformer is plugged in and all electrical connections are

in order.

Confirm that the monitor the keyboard is addressing is the same as the monitor in

front of you.

(KBD100/200A/300A Keyboards only)

Keyboards do not function after installa-

tion and initial power-up.

Confirm that all wiring is correct and that keyboards have power and are connected.

Confirm that each keyboard has been set for a unique address.

Previous system control has been lost.

SOLUTION 1

Initialize the keyboard:

1. Enter the monitor number.

2. Press the MON key.

SOLUTION 2

1. Unplug the data cable from the rear of the keyboard.

2. Plug the data cable back into the rear of the keyboard.

3. Wait five seconds.

4. Re-initialize the keyboard.

SOLUTION 3

1. Power down the CM6800.

2. Power up the system.

3. Wait five seconds.

4. Re-initialize keyboards.

SOLUTION 4

Perform a software reset (refer to Software Reset in this section).

CAUTION: Resetting the software restores the system to default settings. All user

programming is lost. Uploading system settings to the CM6800-MGR before the

software reset allows you to restore system settings after the software reset.

SOLUTION 5

Call Pelco’s 24-hour technical support at 1-800-289-9100 or 1-559-292-1981.

The unit malfunctions and you cannot

restore it to satisfactory operation.

Perform a software reset (refer to Software Reset in this section).

CAUTION: Resetting the software restores the system to default settings. All user

programming is lost. Uploading system settings to the CM6800-MGR before the

software reset allows you to restore system settings after the software reset.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

KBD960/KBR960 ICON/BUTTON LEGEND

LOG

OFF

JOYSTICK

ADJUST

MUX

LOG

OFF

JSTK

ADV

AUX 4, RELAY 4

AUX 5, RELAY 5

AUX 6, RELAY 6

AUX 7, RELAY 7

AUX 8, RELAY 8

QUAD

LOG OFF

YES

ADVANCE

MENUS

MUX

NINE

YES

LOG OFF

SERIAL PORT

TEST

MUX

SIXTEEN

SETUP/DEFINE

KEYBOARD

DOWNLOAD

MUX

LIVE

SAVE

SELECTION

KEYBOARD

UPLOAD

MUX

CAMERA CONTROL

RESET

ALARM

TEST GRAPHIC

PAGE 0

SEQUENCE

DEL

DELETE

SEQ

RESET

ALL ALARMS

CAMERA

PRESET

TEST GRAPHIC

PAGE 1

PRST

TEST GRAPHIC

PAGE 2

MUTE

EXIT

PATTERN

ZONE

CAMERA

SELECTION

TEST TEXT

PAGE 0

ALARM

MONITOR

DEFINE

GPI

MTRY

MAC

DEF

PARITY

SELECTION

SCROLL UP

SCROLL FIELD UP

RELAY

MOMENTARY

DIP SWITCH

TEST

PROGRAM

PGM

SCROLL DOWN

SCROLL FIELD DOWN

MACRO

SELECT

DISPLAY

BRIGHTNESS

DEFINE

NUMBER

DEF

LCD

NUM

PLAY FWD

DEVICE

PAUSE

PROGRAMMING

COM1

COM2

COM3

COM PORT 1

SCROLL RIGHT

PLAY BWD

SCROLL LEFT

COM PORT 2

STOP

SCROLL OPTION

MUX

COM PORT 3

MUX

SCROLL OPTION

DOWN

MUX

AUX 1, RELAY 1

AUX 2, RELAY 2

AUX 3, RELAY 3

TAPE

KEYBOARD

SELECT

MUX

ZOOM

KEYBOARD

KEY TEST

MUX

PIC IN PIC

IN/OUT

FUNCTION

CONTROLS

FORWARD

RUN

BACKWARD

MACRO

RECALL/ALTERNATE

PRESET/LOCK

OTHER

CONTROLS

CAMERA

MONITOR

TURBO

IRIS

CONTROLS

NEAR/FAR

OPEN/CLOSE

ESCAPE

00665

Figure 49. Icon/Button Legend

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

GLOSSARY

Term

Access

Definition

The CM6800 allows you to restrict system control by (1) limiting the monitors or cameras a keyboard

can access, or (2) limiting the cameras that can be viewed on a monitor.

Alarm display format

The CM6800 Matrix Switcher provides four formats for displaying alarmed cameras on system

monitors: Block Build, Chronological Pair, Reverse Chronological Pair, and Salvo Group.

Alarm group

To display on a monitor, an alarm must be assigned to one or more alarm groups. The CM6800-32X6

Matrix Switcher provides six alarm groups (A through F). Refer to Alarm Groups and Alarm Group

Display Options.

Alarm priority

A priority alarm appears on system monitors before a non-priority alarm. Refer to the Priority

description under Internal and External Alarms.

ASCII

The binary, 7-bit, 128-character set implemented as the standard in communications.

Auxiliary

Output relays can be used to control external devices based on matrix switcher activities. External

devices can include VCRs, alarm devices, and triggers for audio circuits.

Baud rate

Bit

In video, the greater the speed, the larger amount of information passed. In digital systems, this

capacity is given in bits per second, or baud rates.

An abbreviation for “binary digit” – the smallest unit of information a computer can use. A bit is either

a 1 or a 0 (a high or low voltage state).

Byte

An abbreviation for “binary term” – bytes are strings of bits, operated upon as a unit. A byte is equal to

eight bits (256 possibilities) and is large enough to hold one character (like an “A” or the number “1”.)

Camera auxiliary

Coaxitron

Some cameras contain an auxiliary output relay, which can be used to operate a device connected to

the relay.

This is Pelco’s “up the coax” control technology. Control signals are sent back up the coaxial cable that

the video signal travels down on.

COM port

This is a communication port input on the rear panel of the matrix switcher.

Daisy-chain

This is a way of providing multiple connections in a series, from one source. A daisy-chain

configuration connects multiple, linked devices from one output. When connecting PTZ cameras to a

matrix switcher, for example, one set of cables connects the matrix switcher to each receiver, and

then each receiver is connected to the next receiver.

Dwell

This is the amount of time something happens in the system, such as the amount of time a camera

view displays on a monitor, or an auxiliary is on.

Event timer

The matrix switcher can automatically initiate macros or sequences based on time and date.

This is Pelco’s Coaxitron control technology that uses 32 bits to send a command.

A three-second camera scan followed by a three-second pause.

Extended Coaxitron

Frame scan

Latching operation

The auxiliary device remains on until a command is given (by a system operator or system automation)

to turn it off.

Logical camera number

Macro

A user-selectable, variable number, which is associated with an actual physical camera input on the

rear panel of the matrix switcher.

A sequence of commands or steps. Macros can be operated automatically or manually. Automatic

operation can be based on specific times or dates (set through the Event Timer).

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Matrix switcher

This is also known as a cross-point switcher. The cross-points are actually electronic switches that

select any video input onto any video output at any one time, preserving the video impedance

matching. One video signal can simultaneously be selected on more than one output. More than one

video input can be selected on one output, in a sequential switching between inputs (unless the input

is routed through a multiplexer, which allows more than one input to be viewed on the output monitor

at any one time).

Momentary operation

Multiplexer (MUX)

The auxiliary output operation is activated briefly and then turns off.

A multiplexer allows an operator to view more than one video signal (usually either four, nine or

sixteen signals) at one time on a single monitor. A multiplexer can also send these multiple images to

the video recorder, switching rapidly between image from each camera.

NTSC

The American color TV standard, used in North America, Japan, and a few other countries. It specifies

525 lines/screen, and 29-30 frames/sec.

Null modem cable

PAL

A null modem cable allows you to connect your PC to another nearby PC or serial device by “crossing

over” (reversing) their respective pin contacts. (A null modem cable is limited to 30 feet in length.)

The color TV standard (50Hz) used by European, Asian, and some Latin American countries. It specifies

768 pixels/line, 576 lines/screen and 25 frames/sec.

Parity type

Pattern

The parity bit is used to identify whether the bits being moved arrived successfully. Parity bit checking

can be based on odd or even bits. No parity means that a parity bit is not transmitted or checked.

A pattern is a user-defined, viewable camera path with a definite beginning and end. The pattern can

consist of any standard pan and tilt or lens command. Once defined, the pattern is easily activated by

a system operator or through an automated event. The pattern will run continuously until it is

deactivated. The number and time length of patterns varies with different positioning systems.

Physical input

Preset

A number representing an actual BNC camera input on the rear panel of the matrix switcher. This

number cannot be changed.

A preset allows operators to direct a PTZ (camera positioning system) to move to a predetermined

scene on keyboard command or as a result of an alarm. In addition to moving the camera, a

descriptive title can appear on the screen. The type of camera positioning system determines the

number of presets available.

Priority control

This is the level of priority a system keyboard has to control a PTZ camera positioning system and to

access CM6800 Matrix Switcher on-screen programming menus.

PTZ

This is a camera positioning system with pan, tilt, and zoom capabilities.

This is a camera scan moving in a random pattern.

Random scan

RJ-45 wall block

This is a wall block with eight terminals for connecting RS-232, RS-422, and RS-485 communication

lines. (This is Pelco part number CON12J00820360Z.)

RS-232

This is an Electronics Industry Association (EIA) interface standard used for data communication; the

normal connection distance is 50 feet (15 m). Pelco uses this standard for communication from a

controller to a PC or RS-232 network. The Pelco three-wire connection provides one wire for transmit,

one wire for receive, and one wire for common.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

RS-422

This is an Electronics Industry Association (EIA) interface standard. Pelco uses this standard for

communication from a controller to one or more camera receivers (on the same line); the maximum

recommended distance is 4,000 feet (1,219 m).

The four-wire connection provides two wires for transmit and two wires for receive. Pelco receiver/

driver communication uses only the two transmit wires (commands are sent from the controller to the

receiver only; the receiver does not “talk” back to the controller). Pelco keyboard communication uses

all four wires.

NOTE: The electrical communication scheme used by Pelco is a direct-coupled method, not an AC-

coupled method. Therefore, if the ground potential of the wire at its two end points is different (other

than zero volts), an additional wire is required as a ground.

RS-485

This is an Electronics Industry Association (EIA) interface standard used for communication between

multiple transmitters and receivers; the maximum recommended distance is 4,000 feet (1,219 m). The

four-wire connection provides two wires for transmit and two wires for receive.

NOTE: The electrical communication scheme used by Pelco is a direct-coupled method, not an AC-

coupled method. Therefore, if the ground potential of the wire at its two end points is different (other

than zero volts), an additional wire is required as a ground.

Scratchpad sequence

Sequence

A scratchpad sequence can be run on an individual system monitor, without entering the password-

protected CM6800 Matrix Switcher on-screen programming menus. You can program scratchpad

sequences from the CM6800 Matrix Switcher on-screen programming menus only, not from the

CM6800-MGR software.

Allows an operator to see a routine of 72 camera views on any system monitor, over and over again.

The sequence can be operated automatically or manually. The order in which the camera views

appear and the time each view remains can be programmed.

Standard Coaxitron

Star configuration

This is Pelco’s Coaxitron control technology that uses 15 bits to send a command.

This is a way of providing multiple direct connections from one source. A star configuration uses a

separate cable for each direct connection, with all of the cables connected to a central device. When

connecting PTZ cameras to a matrix switcher, for example, the central device can be a code distribution

unit, such as the CM9760-CDU-T. Each camera has a direct connection to the CM9760-CDU-T, which is

the central device.

Synchronize

Since the CM6800 can be programmed from either the CM6800-MGR software or the CM6800

programming menus, the two programming sources could potentially have different settings. Pelco

recommends that you always synchronize programming changes between the CM6800-MGR and the

CM6800. Refer to Transmit Programming Settings in the CM6800-MGR Installation/Operation Manual.

System keyboard

This is a keyboard compatible with and connected to the matrix switcher, allowing a system operator

manual control over the system.

System reset

This restores the system to the default settings, as shipped from the factory.

Vertical drive/synchronization

This option sends a timing pulse from the matrix switcher to a compatible camera. The camera aligns

the vertical synchronization with the timing pulse.

Zone

A zone is a user-defined, physical location to which (1) a label is attached and (2) a camera is

associated. When the associated camera is panned through or remains within this defined zone, the

zone label appears on the monitor. With some camera systems, a zone can be blanked to prevent

viewing while the camera is positioned in the zone.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

INDEX

Access 9

Access (partitioning) 38

Addressing

D protocol 8, 14, 48

Date

KBD100/200/300 series keyboards

address 20

display 49

description 10

KBD100/200/300 series keyboards 20

KBD960/KBR960 series keyboards 32

M devices 22

programming 54

Defaults

DIP switches 20

direct-powered connection 19

remote connection 21

KBD960/KBR960 series keyboards

address 32

access 38

DIP switches 62

port 18

Alarms

acknowledge 58

alarm contact programming 39

alarm groups 39, 63

alarm inputs 9, 16, 40

ALM2064 9, 16, 22, 24, 25

block build 39, 63

chronological pair 39, 63

display 39, 63

terminating switch 13

Defaults, system 50, 70

DIP switches

description 10

DIP switches 32

multiple keyboard connection 25

single keyboard connection 23

KBDKIT(-X) 10, 19, 21

Keyboard

ALM2064 24

KBD100/200/300 series keyboards 20

KBD960/KBR960 series keyboards 32

matrix switcher 62

REL2064 24

initialize 31

normally open/normally closed 16

priority level 63

Dwell 47, 53

reverse chronological pair 39, 64

salvo group 39, 64

video loss 41, 49, 61, 66

ALM2064 10

ASCII commands 67

ASCII device 67

Language, select 35

Logical camera number

Event timers 46

Exit (programming) 36

display (on monitor) 48

AUX 1 relay 29

Auxiliaries

M devices

F2 relay 30

addressing 22

installation 22

M protocol 8, 22

Macro

automatic activation 53

connection 9

global 53

installation 29

operation 60

programming 42

REL2064 9, 10, 22, 24, 25, 29, 60

Genex multiplexer

installation 28

automatic activation 46

description 8

operate 58

programming 47, 65

status 47

operation 61

programming 32

Global auxiliaries 53

Models 10

Monitor

Camera

alarm display 39, 63

color bars 33

installation 15

programming (display settings) 48

mounting 11

Help screens 37

access 56, 57

camera title 48

camera/receiver control 56

connection 12, 14

CM6800-MGR software 27, 34, 50, 70

CM9760-CDU-T 10, 14

CM9760-MDA 10

Coaxitron 8, 12, 48

Color bars (monitor) 33

Communication ports

connections 17, 18

port settings 18, 32

programming 51

Installation

alarms 16

auxiliaries 29

cameras 12, 14

Genex multiplexers 28

M devices 22

monitors 15

NTSC 62

PC 27

Interface control 8

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Open collector (TTL) output 30

Operation

R/X type 48

Rack ears 11

Receiver control 56

alarms 58

REL2064 10, 22, 24, 25, 29, 60

Reset, matrix switcher software 70

reversed cable (identifying) 22

RS-422 14

auxiliaries 60

cameras 56

Genex multiplexer 61

macros 58

monitors 55

overview 55

patterns 59

presets 59

PTZ control 56

sequences 57

Scratchpad sequence 52

Sequence

automatic activation 46

description 8

operate 57

programming 52

scratchpad 52

Software

P protocol 8, 14, 48

PAL 62

CM6800-MGR 27, 34, 50, 70

matrix switcher 70

straight cables (identifying) 22

System defaults 50, 70

Partitioning (access) 38

Password

password screen 35

programming 50

Patterns

automatic activation 47, 53

description 8

labels 54

Terminating switch 13

Time

operation 59

display 49

format 54

programming 54

Timers (event) 46

Troubleshooting 70, 71

TTL (open collector) output 30

installation 27

Port address (camera) 32

Power (matrix) 9, 31

Presets

automatic activation 53

description 8

labels 54

Video Loss 66

Video loss

alarm 41, 49

detection 12, 61

Video sources 12

operation 59

Priority control 9, 52

Problems 70, 71

Programming

access 38

alarms 39

auxiliaries 42

date 54

event timers 46

exit 36

Genex multiplexer 32

macros 47, 65

main menu 35

monitor display settings 48

navigation 36

password 50

Zones

description 8, 61

labels 54

ports 51

priority control 52

sequences 52

time 54

PTZ control 12, 14, 56

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

GENERAL

Memory Protection:

Lithium battery, five years of data protection

Keyboards:

Ten: Eight KBD100/200A/300A Series keyboards and two KBD960/KBR960 Series keyboards. (Switcher

can provide power for one KBD100/200A/300A Series keyboard. Additional keyboards will require a

remote power supply.)

Receiver/Dome Control:

Alarm Inputs:

Coaxitron and RS-422

Eight individually programmable for N.O. or N.C. on rear panel (plus an additional 128, via ALM2064,

Alarm Interface Units, providing a total of 136 possible)

Control Outputs on Rear Panel

AUX 1:

F2:

One relay (SPDT), rated at 0.5 amp @ 125 V, 1 amp @ 30 VDC, 60 milliohms contact resistance

One open collector (TTL); 15 VDC maximum, 25 mA maximum

Additional Outputs:

Two REL2064, Relay Interface Units, may be connected to expand relay outputs to a maximum of 128

Five data ports, one PTZ control port, flexible configuration options; one port provides power for keyboard

Communication Ports:

ELECTRICAL

Input Power:

Power Consumption:

120 V or 230 V, 50/60Hz

25 W

SWITCHER CHARACTERISTICS

Video Inputs, Looping:

32 BNC, terminating or looping (individually selectable per camera), .5 to 2.0 Vp-p composite video, video

loss detection

Six outputs, BNC

Video Outputs:

Switching Type:

Switching Method:

Switching Time:

Cross-point video matrix, NTSC and PAL compatible

Vertical interval switching

Less than 16 milliseconds (typical)

VIDEO

Bandwidth:

15 MHz

Frequency Response:

Signal-to-Noise Ratio:

Adjacent Channel Crosstalk:

Differential Gain:

Differential Phase:

Gain:

Flat to 8 MHz, ±1dB to 13 MHz

-50 dB (peak-to-peak vs. RMS noise)

-55 dB typical at 3.58 MHz

0.03% typical

0.24° typical

Unity (±1dB)

DC Output:

Zero volts

CHARACTER GENERATION

Character Type:

Camera Identification:

White with black outline; adjustable brightness

Two lines, twenty-character title, plus camera number, monitor number, date (four formats) and time (24-

hour or AM/PM formats)

On-screen, menu-driven

128 ASCII characters

Programmable:

Character Set:

ENVIRONMENTAL

Ambient Operating

Temperature:

20° to 120°F (-7° to 49°C)

10-90% non-condensing

Humidity:

MECHANICAL

Dimensions:

Mounting:

17.40 (W) x 5.25 (H) x 12.25 (D) inches (without rack ears) (44.20 x 13.34 x 31.12 cm)

Factory-configured for EIA rack mount (3 RU); rack ears can be removed for versatile wall mount or

freestanding applications

Unit Weight:

12.7 lb (5.76 kg)

(Design and product specifications subject to change without notice.)

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

REGULATORY NOTICES

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to part 15 of the FCC rules. These

limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful

interference to radio communications. However there is no guarantee that the interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-TV Interference Problems.” This

booklet is available from the U.S. Government Printing Office, Washington D.C. 20402.

Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate

this equipment under Federal Communications Commission’s rules.

WARRANTY AND RETURN INFORMATION

WARRANTY

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to

obtain a Repair Authorization number (RA), and provide the following information:

Pelco will repair or replace, without charge, any merchandise proved defective in material or

workmanship for a period of one year after the date of shipment. Exceptions to this warranty

are as noted below:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Five years on the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2,

CC3651H-2X, MC3651H-2, and MC3651H-2X.

Three years on all other fixed camera models (including Camclosure^®Integrated Camera

Systems) and Genex^®Series (multiplexers, server, and keyboard).

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions

stated above, please include a written explanation with the product when returned.

•

Two years on all standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM6800E/CM8500/CM9500/CM9700 Series Matrix,

DF5 and DF8 Series Fixed Dome products.

Two years on Spectra^®, Esprit^®, and PS20 Scanners, including when used in continuous motion

applications.

Two years on Esprit^®and WW5700 series window wiper (excluding wiper blades).

Method of return shipment shall be the same or equal to the method by which the item was received by

Pelco.

RETURNS

•

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100

or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if

returned for repair).

•

Eighteen months on DX Series digital video recorders and NVR300 network video recorders.

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered

for a period of six months.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and

freight should be prepaid. Ship to the appropriate address below.

•

Six months on all pan and tilts, scanners or preset lenses used in continuous motion applica-

tions (that is, preset scan, tour and auto scan modes).

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico send the goods to:

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.

All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis, California. Repairs

made necessary by reason of misuse, alteration, normal wear, or accident are not covered under

this warranty.

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the

specific use or application made of the Products. Pelco’s liability for any claim, whether based on

breach of contract, negligence, infringement of any rights of any party or product liability, relating

to the Products shall not exceed the price paid by the Dealer to Pelco for such Products. In no

event will Pelco be liable for any special, incidental or consequential damages (including loss of

use, loss of profit and claims of third parties) however caused, whether by the negligence of

Pelco or otherwise.

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return

goods to the USA, you may do one of the folllowing:

If the goods are to be sent by a COURIER

SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT

FORWARDER, send the goods to:

Pelco

Pelco c/o Expeditors

473 Eccles Avenue

South San Francisco, CA 94080 USA

3500 Pelco Way

Clovis, CA 93612-5699 USA

The above warranty provides the Dealer with specific legal rights. The Dealer may also have

additional rights, which are subject to variation from state to state.

Phone: 650-737-1700

Fax: 650-737-0933

REVISION HISTORY

Manual #

C1522M

Date

10/01

1/02

2/02

5/03

6/04

Comments

Preliminary version for software version 2.00 Beta.

Original version.

Updated certifications.

Updated with additional functionality (such as Macros triggered by alarms).

Removed reference to use 18-gauge wire for EIA RS-485 communication. Updated Important Safeguards and Warnings. Revised Tables B, G, and J, and Figures 46

and 48.

C1522M-A

C1522M-B

C1522M-C

2/05

Added information on new feature allowing the use of macros for up to three alarm steps; revised memory protection timeframe (as a result of ECO #04-10477).

Revised Figure 14 and replaced Figure 20 with previous version from C1522M-A.

Pelco, the Pelco logo, Spectra, Genex, Legacy, Camclosure, Esprit, and Coaxitron are registered trademarks of Pelco.

C1522M-C (2/05)

Download from Www.Somanuals.com. All Manuals Search And Download.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO9001

Download from Www.Somanuals.com. All Manuals Search And Download.

Pelco DVR DX4500 User Manual
Pelco Flat Panel Television PMCL526A User Manual
Pentax Camcorder IQZoom140 User Manual
Philips Computer Drive VR600 User Manual
Philips Home Safety Product SFL7146 27 User Manual
Philips Projection Television 28PW962B User Manual
Poulan Chainsaw BH 2160 User Manual
Power Acoustik Car Speaker FUBAR 10W User Manual
Presto Fryer Electric Skille User Manual
Promise Technology Network Card TX4000 User Manual