Pelco Marine Radio TXB V User Manual

INSTALLATION/OPERATION

TXB-V

Translator Board

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Only use attachments/accessories specified by the manufacturer.

6. Installation should be done only by qualified personnel and conform to all local codes.

Only use replacement parts recommended by Pelco.

The product and/or manual may bear the following marks:

This symbol indicates that dangerous voltage

constituting a risk of electric shock is present within

this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

This symbol indicates that there are important

DO NOT OPEN.

operating and maintenance instructions in the

literature accompanying this unit.

Important Notice

All companies make changes and improvements in their products on a regular basis. Because this product

is interfacing with equipment not manufactured by Pelco, the possibility exists that the interface protocols

have changed or are in a different configuration from earlier tested units; therefore, an incompatibility may

occur. The existence of prior successful installations indicates our intent to provide equipment compatible

with other manufacturers, but does not guarantee successful results without on-site integration testing.

Pelco recommends purchasing a single unit for bench testing before the purchase and

installation of this product in quantity. Should any problems occur, Pelco will provide on-site technical

support (North American installations only) to analyze the interface protocols of your system. We will

typically schedule this visit within one week of when the problem is reported to Pelco Technical Support.

Pelco will endeavor, at its expense, to correct the interface incompatibility within two weeks on a high

priority basis. During these visits, the end user must agree to give Pelco reasonable access to the system

in order to study and correct the protocol incompatibility.

In the unlikely event that Pelco is unable to make the translator work in the system, Pelco will accept the

return of any Pelco products associated with the translator and refund the amounts paid for these products

plus freight expenses. Because Pelco recommends a bench test prior to installation, Pelco will not be

liable for any installation costs or lost revenues in the event it cannot solve the compatibility problem.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Regulatory Notices

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

RADIO AND TELEVISION INTERFERENCE

This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However there is no guarantee that the interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and the receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•

Consult the dealer or an experienced radio/TV technician for help.

You may also find helpful the following booklet, prepared by the FCC: “How to Identify and Resolve Radio-

TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington

D.C. 20402.

Changes and modifications not expressly approved by the manufacturer or registrant of this equipment can

void your authority to operate this equipment under Federal Communications Commission’s rules.

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The materials used in the manufacture of this document and its components are compliant to

the requirements of Directive 2002/95/EC.

This equipment contains electrical or electronic components that must be recycled properly to

comply with Directive 2002/96/EC of the European Union regarding the disposal of waste

electrical and electronic equipment (WEEE). Contact your local dealer for procedures for

recycling this equipment.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Description

The TXB-V translator board allows Vicon^®controllers to communicate with Pelco’s ExSite^™, Esprit^®, and

Spectra^®systems. After setup, the controller functions the same as a Vicon controller normally would,

except as noted in the Operation section on page 21.

The TXB-V translator board has been tested and shown to work with the following Vicon systems:

•

V1300X-DVC Remote Control Panel

VPS324 Matrix Controller

V1422^™Matrix Controller

V4480SCC Matrix 44^®Card Cage

V6680SCC Matrix 66^™Card Cage

Based on the information published by the manufacturer, Pelco has reason to believe that the translator

board will also work with the following Vicon models:

•

VPS1344^™Matrix Switching System

V1300 Series NOVA^™Programmable Matrix Switching System

V1400X-DVC System Console Control Station

Parts List

The following items are supplied:

1 TXB-V translator board (printed circuit board)

1 6-32 screw with lock washer (for Spectra III^™/Spectra IV Series only)

1 4-40 screw with lock washer (unused)

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Esprit Installation

To install the TXB-V translator board in an Esprit system (refer to Figure 1):

1. Turn off power to the Esprit system.

2. Remove the left cover from the pan and tilt.

3. Remove the shorting plug from the 16-pin connector on the Esprit system’s circuit board.

4. Remove the nut and washer from the standoff on the Esprit system’s circuit board.

NOTES:

•

Discard the 6-32 and 4-40 screws and their lock washers; they are not used in the Esprit system.

Save the 16-pin shorting plug. Otherwise, the Esprit cannot be converted back to a Pelco-controlled

system.

OFF

12345678

OFF

DIP SWITCHES

NYLON

WASHER

PHILLIPS

SCREW

ESPRIT CIRCUIT BOARD

16-PIN CONNECTOR

REMOVE SHORTING PLUG

STANDOFF WITH

NUT AND WASHER

Figure 1. Esprit System

5. Set the P2 jumper on the TXB-V to the proper termination setting (refer to Figure 2). Note the

following:

•

By default, the P2 jumper is installed in the unterminated position.

All TXB-Vs in a daisy chain, except the last unit, must be unterminated.

The total wire distance from the Vicon controller to the last TXB-V in a daisy chain must be

less than 4,000 ft (1,219 m).

•

A maximum of 10 receivers can be installed on a single daisy chain.

To unterminate a TXB-V, remove the P2 jumper from the TXB-V and place it over one pin for

storage.

NOTE: When combining Pelco and Vicon receivers in the same system, refer to the Vicon manual for

proper RS-485 configuration of the Vicon receiver(s).

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

P3 & P4 JUMPERS

P2 UNTERMINATED

P2 TERMINATED

P2 JUMPER

16-PIN CONNECTOR

Figure 2. TXB-V Termination and Baud Rate (Bottom View)

6. Set the baud rate for the TXB-V translator board (from the controller). Use the P3 and P4 jumpers

(refer to the following table).

Baud

600

OFF

4800*

9600

19.2K

*Factory default.

7. Install the TXB-V on the Esprit circuit board (refer to Figure 3):

Insert the 16-pin connector on the bottom of the TXB-V into the mating 16-pin connector on

the Esprit circuit board.

Reinstall the nut and washer on the standoff to secure the TXB-V to the Esprit circuit board.

STANDOFF

16-PIN CONNECTOR

STANDOFF NUT

AND WASHER

Figure 3. Installing the TXB-V into the Esprit

8. Set the DIP switches on the Esprit system (refer to Figure 1 on page 6 for switch location):

SW1: Set all SW1 switches to the OFF position.

SW2: Set the Esprit address (refer to Table A on page 24 of the Appendix for switch settings).

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

9. Reinstall the left cover of the pan and tilt:

WARNING: Make sure you seal the unit. Otherwise, moisture could disable or damage

the Esprit.

Properly position the cover and slide it into place. The sides of the cover must fit under the

front and back rain guards of the pan and tilt. The top of the cover must seat against the lip of

the top gasket. (Refer to Figure 4.)

NOT SEALED

CORRECT

INCORRECT

GAP

Figure 4. Installing the Esprit Cover

Apply pressure and push the top of the cover down to align the screw holes (refer to Figure 5).

Insert the Phillips screw and washer. Tighten until the screw will not turn.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

TOP GASKET

FRONT

RAIN

GUARD

Figure 5. Fastening the Esprit Cover

10. Remove the pan and tilt from the base of the Esprit system.

11. Check the control wiring inside the base of the unit. Refer to the Esprit documentation and the

documentation supplied with your controller to make sure the wiring is correct.

Vicon Controller

Terminal Block J1

Esprit

Wire Harness

Pin 9 Response Out +

Pin 8 Response Out -

Pin 3 Command In +

Pin 2 Command In -

White (TX+)

Black (TX-)

Red (RX+)

Green (RX-)

12. Reattach the pan and tilt onto the base of the unit.

13. Apply power to the system. The following message appears on the monitor as soon as the Esprit

configuration cycle is completed:

TXB-V REV x.xx

NOTE: x.xx represents the current firmware revision.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Spectra III/Spectra IV Installation

To install the TXB-V translator board in a Spectra III/Spectra IV Series:

1. Turn off power to the dome system.

2. Remove the lower dome.

3. Remove the dome drive by pressing in the blue and red tabs on the sides of the dome drive. Gently

rock the dome drive to release it from the back box.

4. Set the P2 jumper on the TXB-V to the proper termination setting (refer to Figure 6). Note the

following:

•

By default, the P2 jumper is installed in the unterminated position.

All TXB-Vs in a daisy chain, except the last unit, must be unterminated.

The total wire distance from the Vicon controller to the last TXB-V in a daisy chain must be

less than 4,000 ft (1,219 m).

•

A maximum of 10 receivers can be installed on a single daisy chain.

To unterminate a TXB-V, remove the P2 jumper from the TXB-V and place it over one pin for

storage.

NOTE: When combining Pelco and Vicon receivers in the same system, refer to the Vicon manual for

proper RS-485 configuration of the Vicon receiver(s).

P3 & P4 JUMPERS

P2 UNTERMINATED

P2 TERMINATED

P2 JUMPER

16-PIN CONNECTOR

Figure 6. TXB-V Termination and Baud Rate (Bottom View)

5. Set the baud rate for the TXB-V translator board (from the controller). Use the P3 and P4 jumpers

(refer to the following table).

Baud

600

OFF

4800*

9600

19.2K

*Factory default.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Install the TXB-V translator board into the back box:

Open the hinged door to the back box. Push the tab lock towards the back box wall of the unit

and open the door (refer to Figure 7).

Figure 7. Spectra III/Spectra IV Back Box Interconnect Door

Check the wiring to the controller. Refer to the Spectra III/Spectra IV documentation and the

documentation supplied with your controller to make sure the wiring is correct.

Vicon Controller

Terminal Block J1

Spectra III/Spectra IV

Four-Wire Terminal Block

Pin 9 Response Out +

Pin 8 Response Out -

Pin 3 Command In +

Pin 2 Command In -

TX+

TX-

RX+

RX-

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Remove the shorting plug from the 16-pin connector located on the back box circuit board

(refer to Figure 8).

6-32 SCREW AND

LOCK WASHER

REMOVE SHORTING

PLUG

16-PIN CONNECTOR

STANDOFF

Figure 8. Spectra III/Spectra IV Back Box Circuit Board

NOTES:

•

Discard the 4-40 screw and its lock washer; they are not used in the Spectra III/Spectra IV

system.

•

Save the 16-pin shorting plug. Otherwise, the Spectra III/Spectra IV cannot be converted back

to a Pelco-controlled system.

Insert the TXB-V board into the 16-pin connector located on the back box circuit board. Secure

the translator board to the standoff on the circuit board using the supplied 6-32 screw and

lock washer.

Close the interconnect door. Snap the tab lock into place.

7. Set the DIP switches on the Spectra III/Spectra IV system (refer to Figure 9 and Figure 10 on page 13

for switch locations):

Set the SW1 switches on the dome drive to assign the address (refer to Table A on page 24 of

the Appendix for switch settings).

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

For Spectra III systems, set all SW3 switches on the dome to the OFF position.

For Spectra IV systems, set SW2-1 through SW2-8 to the OFF position.

SW1 SW3

SW2

SW1 AND SW2

Figure 9. Spectra III Dome Drive DIP Switches

Figure 10. Spectra IV Dome Drive DIP Switches

8. Install the dome drive (refer to Figure 11). Line up the blue (A) and red (B) tabs with the blue (A) and

red (B) labels. When pushing the tabs in, insert one side, then the other. Continue pushing on the

ends of the tabs until both tabs click into place.

NOTE: Refer to the installation manual supplied with the Spectra III/Spectra IV dome for instructions

on installing the back box, dome drive, and lower dome.

Figure 11. Spectra III/Spectra IV Dome Drive Installation

9. Install the lower dome.

10. Apply power to the system. The following message appears on the monitor as soon as the

Spectra III/Spectra IV configuration cycle is completed:

TXB-V REV x.xx

NOTE: x.xx represents the current firmware revision.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Spectra Mini Dome Installation

To install the TXB-V translator board in a Spectra Mini dome:

NOTE: Installing a TXB-V into a mini dome increases unit height. In surface mount installations, you must

cut a hole in the surface to accommodate the TXB-V cover. For an installation template and more

information, refer to the Spectra Mini Dome Installation manual.

1. Turn off power to the dome system.

2. If the Spectra Mini dome is already installed, remove it to access the top of the dome drive where

the translator board will be installed.

3. Place the dome drive on a flat surface with the dome liner pointing up.

4. Set the DIP switches on the dome (refer to Figure 12 for switch location):

NOTE: There are no SW1 switch settings on the Spectra Mini dome.

Point the camera straight up.

Using a flashlight, look through the viewing slot of the dome liner. Rotate the dome liner until

you see two DIP switches in the bottom of the housing.

SW 3

SW 2

Figure 12. Locating the Spectra Mini Dome DIP Switches

SW2: Set all switches to the OFF position.

SW3: Set the Spectra Mini dome address (refer to Table A on page 24 of the Appendix for

switch settings).

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Set the P2 jumper on the TXB-V to the proper termination setting (refer to Figure 13). Note the

following:

•

By default, the P2 jumper is installed in the unterminated position.

All TXB-Vs in a daisy chain, except the last unit, must be unterminated.

The total wire distance from the Vicon controller to the last TXB-V in a daisy chain must be

less than 4,000 ft (1,219 m).

•

A maximum of 10 receivers can be installed on a single daisy chain.

To unterminate a TXB-V, remove the P2 jumper from the TXB-V and place it over one pin for

storage.

NOTE: When combining Pelco and Vicon receivers in the same system, refer to the Vicon manual for

proper RS-485 configuration of the Vicon receiver(s).

P3 & P4 JUMPERS

P2 UNTERMINATED

P2 TERMINATED

P2 JUMPER

16-PIN CONNECTOR

Figure 13. TXB-V Termination and Baud Rate (Bottom View)

6. Set the baud rate for the TXB-V translator board (from the controller). Use the P3 and P4 jumpers

(refer to the following table).

Baud

600

OFF

4800*

9600

19.2K

*Factory default.

7. Install the TXB-V translator board (refer to Figure 14 and Figure 15 on page 16):

Remove the cover from the top of the dome drive.

Remove the shorting plug from the 16-pin connector located on the Spectra Mini dome circuit

board.

NOTES:

•

Discard the 4-40 and 6-32 screws and their lock washers; they are not used in the

Spectra Mini dome.

•

Save the 16-pin shorting plug and the original cover from the Spectra Mini dome.

Otherwise, the unit cannot be converted back to a Pelco-controlled system.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

REMOVE

SHORTING

PLUG

Figure 14. Removing the Mini Dome Cover and Shorting Plug

Insert the TXB-V translator board into the 16-pin connector on the Spectra Mini dome’s circuit

board.

Install the translator board cover that is supplied with the Spectra Mini dome.

Figure 15. Installing the TXB-V and Mini Dome Cover

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

8. Check the wiring to the controller. Refer to the Spectra Mini dome documentation and the

documentation supplied with your controller to make sure the wiring is correct.

Vicon Controller

Terminal Block J1

Spectra Mini Dome

RJ45-10 Connector

Pin 9 Response Out +

Pin 8 Response Out -

Pin 3 Command In +

Pin 2 Command In -

Pin 6 (TX+)

Pin 5 (TX-)

Pin 4 (RX+)

Pin 3 (RX-)

9. Refer to the installation manual for the Spectra Mini dome to complete the installation.

10. Apply power to the system. The following message appears on the monitor as soon as the Spectra

Mini dome configuration cycle is completed:

TXB-V REV x.xx

NOTE: x.xx represents the current firmware revision.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

ExSite Installation

To install the TXB-V translator board in an ExSite unit:

WARNING: To reduce the risk of ignition of hazardous atmospheres, disconnect the

equipment from the supply circuit before opening.

1. Turn off the power to the ExSite system.

WARNING: Total weight of the pan and tilt component is 55 lb (25 kg). Use caution

when lifting and assembling the pan and tilt component on the power module. It is

recommended that nonslip gloves be worn during installation or removal.

2. Remove the pan and tilt unit from the power module (refer to Figure 16 and Figure 17):

Loosen the setscrew in the locking ring with a 2 mm Allen wrench.

Loosen the locking ring with a spanner wrench (Pelco part #MF00-1251-121A).

Carefully unscrew the locking ring and remove the pan and tilt unit from the power module.

PAN AND

TILTUNIT

LOCKING

RING

Figure 16. ExSite Spanner Wrench

POWER

MODULE

Figure 17. Removing the ExSite Pan and Tilt Unit

3. Set the P2 jumper on the TXB-V to the proper termination setting (refer to Figure 18 on page 19).

Note the following:

•

By default, the P2 jumper is installed in the unterminated position.

All TXB-Vs in a daisy chain, except the last unit, must be unterminated.

The total wire distance from the Vicon controller to the last TXB-V in a daisy chain must be

less than 4,000 ft (1,219 m).

•

A maximum of 10 receivers can be installed on a single daisy chain.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

•

To unterminate a TXB-V, remove the P2 jumper from the TXB-V and place it over one pin for

storage.

NOTE: When combining Pelco and Vicon receivers in the same system, refer to the Vicon manual for

proper RS-485 configuration of the Vicon receiver(s).

P3 & P4 JUMPERS

P2 UNTERMINATED

P2 TERMINATED

P2 JUMPER

16-PIN CONNECTOR

Figure 18. TXB-V Termination and Baud Rate (Bottom View)

4. Set the baud rate for the TXB-V translator board (from the controller). Use the P3 and P4 jumpers

(refer to the following table).

Baud

600

OFF

4800*

9600

19.2K

*Factory default.

5. Install the TXB-V board on the power module (refer to Figure 19 on page 20):

Remove the shorting plug from the 16-pin connector located on the ExSite system’s circuit

board.

NOTES:

•

Discard the 6-32 and 4-40 screws and their lock washers; they are not used in the

ExSite system.

•

Save the 16-pin shorting plug. Otherwise, the ExSite cannot be converted back to a

Pelco-controlled system.

Insert the TXB-V board into the 16-pin connector on the ExSite system’s circuit board. Confirm

that the TXB-V board is fully seated into the 16-pin connector.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

16-PIN

CONNECTOR

SW1

SW3

Figure 19. Installing the TXB-V into the ExSite

6. Check the wiring to the controller. Refer to the ExSite documentation and the documentation

supplied with your controller to make sure the wiring is correct.

Vicon Controller

Terminal Block J1

ExSite

Wire Harness

Pin 9 Response Out +

Pin 8 Response Out -

Pin 3 Command In +

Pin 2 Command In -

White/Orange (TX+)

White/Blue (TX-)

Red (RX+)

Green (RX-)

7. Set the DIP switches on the ExSite system (refer to Figure 19 for switch location):

SW3: Verify that all SW3 switches on the ExSite power module are set to the OFF position.

SW1: Set the ExSite address (refer to Table A on page 24 of the Appendix for switch settings).

8. Attach the pan and tilt unit to the power module (refer to Figure 16 and Figure 17 on page 18):

Align the pan and tilt unit with the power module. Carefully begin to hand tighten the locking

ring onto the threads of the power module.

Continue to tighten the locking ring with a spanner wrench.

Tighten the setscrew in the locking ring with a 2 mm Allen wrench.

NOTE: Refer to the installation manual supplied with the ExSite system for instructions on attaching

the pan and tilt unit to the power module.

9. Apply power to the system. The following message appears on the monitor as soon as the ExSite

configuration cycle is completed:

TXB-V REV x.xx

NOTE: x.xx represents the current firmware version.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Set preset 94 to access the camera menus. Press Iris Open to select menu items. The following table

shows how the Vicon keyboard relates to the Pelco translator. Refer to your Vicon documentation for

operating instructions.

SPECIAL FUNCTIONS DEFINITIONS

Vicon Keyboard

Unit Function

Pelco Function

Pan, tilt, zoom, focus, and Moves unit accordingly

iris functions

Pan, tilt, zoom, focus, and iris

functions

(Keyboard in PGM Mode)

1-32 Preset

Saves camera position as preset 1-32

Sets preset 1-32

33-64 Preset

Saves camera position as preset 33-64 Sets preset 35-66

AUX toggle 1-2 (On/Off)

AUX toggle 3-6

Activates auxiliaries 1-2

No action on Pelco receivers

Toggles auxiliaries 1-2 on/off

Ignored

Auto pan toggle (On)

Auto pan toggle (Off)

Runs auto pan

Stops auto pan

Calls preset 99

Calls preset 96

(Keyboard in RUN Mode)

1-32 Preset

33-64 Preset

65 Preset

66 Preset

67-87 Preset

88 Preset

89 Preset

90 Preset

91 Preset

92 Preset

Moves camera to preset position 1-32

Moves camera to preset position 33-64 Calls preset 35-66

Camera flips 180 degrees

Pans to zero

No action

Runs pattern 1 (short)

Runs pattern 2 (short)

Runs long pattern

Inserts IR filter*

Removes IR filter*

Stops scanning

Runs random scan

Runs frame scan

Runs auto scan

Calls preset 1-32

Calls preset 33

Calls preset 34

Ignored

Calls pattern #1

Calls pattern #2

Calls long pattern

Calls preset 88

Calls preset 89

Calls preset 96 (stop scan)

Calls preset 97

Calls preset 98

Calls preset 99

96 Preset

97 Preset

98 Preset

99 Preset

(Keyboard in PGM Mode)

65-79 Preset

80-87 Preset

Auto pan key

88 Preset

89 Preset

90 Preset

91 Preset

92 Preset

93 Preset

94 Preset

No action

Sets start point (left limit) of zones 1-8

Sets end point (right limit) of zones 1-8 Sets zone 1-8 end

Begins programming pattern #1

Begins programming pattern #2

Begins programming long pattern

Ends programming of a pattern

Sets manual pan left limit***

Sets manual pan right limit***

Shows program menu**

Ignored

Sets zone 1-8 start

Sets pattern #1 (short)

Sets pattern #2 (short)

Sets long pattern (#0)

Ends pattern programming

Sets preset 90

Sets preset 91

Sets preset 95

95 Preset

96 Preset

97 Preset

Enables zone label display

Disables zone label display

Performs power-on reset

Displays zone label

Returns to normal screen

Remote reset

98 Preset

99 Preset

Lens speed toggle

Sets Auto pan left limit***

Sets Auto pan right limit***

Sets zoom speed

Sets preset 92

Sets preset 93

Toggles through zoom speeds

Auto iris toggle (On/Off)

Controls auto iris

Auto on/off

*Spectra SD53CBW family, Spectra SD435 family, Esprit ES30CBW18 family, Esprit ES31CBW18

family, ExSite IPSXM30CBW family, ExSite IPSXM31CBW family, ExSite EHXM30CBW family,

and ExSite EHXM31CBW family.

**Iris Open selects menu items.

***Refer to the Pelco system operation manuals for details on how to clear limit stops.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

TXB-V ZONE PROGRAMMING PROCEDURE

A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. To program a zone

using a Vicon controller (refer to the manual supplied with the controller):

Step

Procedure

1. Set left zone limit.

a. Position the Pelco unit at the left limit of the zone.

b. Issue the zone start command (PRG 8# PRESET) for the zone

number being programmed; # is a number between 0 and 7 that

represents zones 1 through 8.

2. Set right zone limit.

a. Position the Pelco unit at the right limit of the zone.

b. Issue the zone end command by pressing the Auto Pan key.

Issue the enable zone label command (PRG 95 PRESET) to display

the zone label.

3. Enable the zone label display.

IMPORTANT: (Spectra III/Spectra IV and ExSite systems only): After programming a zone, always enable

the zone through the Pelco unit programming menu. Refer to the operation/programming manual supplied

with the Pelco system.

Operation Notes:

1. Focus speed cannot be set with the Vicon controller.

2. The Event Tour function on the Vicon controller does not function.

3. On-screen titling is only available on Spectra III/Spectra IV (v1.28 and higher).

4. Zone labels use only defaults (Zone 1, Zone 2, etc.)

5. Upon completion of pattern programming, issue an end pattern command (91 Set on the Vicon

controller) to enable Turbo speed during panning. If this is not done, Turbo speed will be unavailable

until 10 minutes after starting pattern programming.

6. Alarms from the Pelco receiver will not activate alarm LEDs on the Vicon controller.

7. LEDs on the Vicon controller may be out of sync when the receiver’s start-up defaults are changed,

when the receiver is reset, or if a receiver alarm triggers a status change. To correct, press and

release the affected key.

8. The communication parameters that are displayed momentarily on the selected monitor immediately

after initial power-up pertain only to the communication link between the translator board and the

Pelco unit. Communication parameters between the translator board and the Vicon controller are

selected with jumpers P3 and P4.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Troubleshooting

Symptom

Possible Cause

Suggested Remedy

No video is displayed.

Power is not connected to the

Pelco unit.

Check the power connector.

Video cable is not connected to Check the video connector.

the Pelco unit.

Translator board is not inserted Reinstall the translator board.

properly.

Make sure the pins on the

board are inserted correctly.

Pelco unit information (model,

firmware, Pelco P and D

addresses, and communication

settings) does not appear after

the configuration cycle.

The Pelco unit cannot complete Refer to the troubleshooting

its configuration cycle.

section of the product manual

for the Pelco unit.

The message “TXB-V REV x.xx” The baud rate setting on the

Make sure the baud rate setting

on the Pelco unit is 2400. Then

cycle device power.

does not appear.

Pelco unit is not correct. The

setting appears on power-up.

The Pelco unit does not respond The unit address is not correct.

to commands.

Make sure the Pelco unit

(receiver) address is correct.

This address can range from 1

to 255.

Make sure the controller is

addressing the correct Pelco

unit.

The receiving and transmitting

lines are not connected

properly.

Make sure the TX+, TX-, RX+,

and RX- lines are properly

connected. (Refer to the wiring

tables in this manual as well as

the troubleshooting section of

the product manual for the

controller.)

The command was lost

between the controller and the

Pelco unit.

Retry the command.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Appendix

Table A. Receiver Address Settings

Switch Setting

Receiver

Address

OFF

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Receiver Address Settings (Continued)

Switch Setting

Receiver

Address

OFF

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Receiver Address Settings (Continued)

Switch Setting

Receiver

Address

OFF

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Receiver Address Settings (Continued)

Switch Setting

Receiver

Address

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

OFF

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Receiver Address Settings (Continued)

Switch Setting

Receiver

Address

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

OFF

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Receiver Address Settings (Continued)

Switch Setting

Receiver

Address

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

237

OFF

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table A. Receiver Address Settings (Continued)

Switch Setting

Receiver

Address

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

255

OFF

REVISION HISTORY

Manual #

C656M

C656M-A

C656M-B

C656M-C

C656M-D

Date Comments

9/00 Original version.

12/02 Updated manual to new format. Added instructions for Spectra III SE and Spectra III.

5/03 Added instructions for zone programming.

3/05 Added ExSite system installation instructions. Corrected wiring table for controller.

3/06 Added Spectra Mini dome. Removed Spectra II. Updated graphics and procedures.

C656M-E

4/07 Added Green label, cross references, and Spectra IV. Added Important Safety Instructions.

C656M-E (4/07)

Download from Www.Somanuals.com. All Manuals Search And Download.

PRODUCT WARRANTY AND RETURN INFORMATION

WARRANTY

Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of

shipment.

Exceptions to this warranty are as noted below:

•

Five years on fiber optic products and TW3000 Series unshielded twisted pair transmission products.

Three years on Spectra^®IV products.

Three years on Genex^®Series products (multiplexers, server, and keyboard).

Three years on Camclosure^®and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and

MC3651H-2X camera models, which have a five-year warranty.

•

Three years on PMCL200/300/400 Series LCD monitors.

Two years on standard motorized or fixed focal length lenses.

Two years on Legacy^®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.

Two years on Spectra III^™, Esprit^®, ExSite^®, and PS20 scanners, including when used in continuous motion applications.

Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).

Two years (except lamp and color wheel) on Digital Light Processing (DLP^®) displays. The lamp and color wheel will be covered for a period of

90 days. The air filter is not covered under warranty.

Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and Endura^™Series distributed network-based video

products.

•

One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.

Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).

Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight

prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this

warranty.

Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products

shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential

damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.

The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state

to state.

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and

provide the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written

explanation with the product when returned.

Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.

RETURNS

In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization

number (CA number if returned for credit, and RA number if returned for repair).

All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.

Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate

address below.

If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:

Service Department

Pelco

3500 Pelco Way

Clovis, CA 93612-5699

If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the

following:

If the goods are to be sent by a COURIER SERVICE, send the goods to:

If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:

Pelco

Pelco c/o Expeditors

3500 Pelco Way

Clovis, CA 93612-5699 USA

473 Eccles Avenue

South San Francisco, CA 94080 USA

Phone: 650-737-1700

Fax: 650-737-0933

Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.

Spectra III, Endura, and ExSite are trademarks of Pelco.

DLP is a registered trademark of Texas Instruments, Inc.

Vicon and Matrix 44 are registered trademarks of Vicon Industries, Inc.

V1422, VPS1344, Matrix 66, and NOVA are trademarks of Vicon Industries, Inc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Worldwide Headquarters

3500 Pelco Way

Clovis, California 93612 USA

USA & Canada

Tel: 800/289-9100

Fax: 800/289-9150

International

Tel: 1-559/292-1981

Fax: 1-559/348-1120

www.pelco.com

ISO9001

Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore

South Africa Spain Sweden United Arab Emirates United Kingdom United States

Download from Www.Somanuals.com. All Manuals Search And Download.

Peavey Music Mixer MPA 700T User Manual
Pentax Camcorder PV C850A User Manual
Philips Car Video System 298P4 User Manual
Philips Network Card VOIP0211G User Manual
Philips TV DVD Combo 4PT6107 User Manual
Philips TV Receiver 29PT5435 User Manual
Philips Work Light 157255 User Manual
Polk Audio Speaker DSW PRO 400 User Manual
Porter Cable Air Compressor D24225 049 2 User Manual
PYLE Audio CD Player PT 688CU User Manual