Pelco Home Security System c1487 c User Manual

SD5 Series

Spectra II™ and

Spectra Lite™ Dome

Installation/

Operation Manual

C1487M-C (7/99)

LISTED

Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com

In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108

International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 • DataFAX (1-559) 292-0435

Download from Www.Somanuals.com. All Manuals Search And Download.

Section

Page

LIMIT STOPS ....................................................................................................41

PARK TIME MINUTES......................................................................................42

SCAN SPEED ...................................................................................................42

PATTERN LENGTH ..........................................................................................42

TROUBLESHOOTING ......................................................................................................43

BACK BOX ELECTRONIC ASSEMBLY REMOVAL .................................................45

MAINTENANCE ................................................................................................................45

DOME CLEANING ....................................................................................................45

SERVICE MANUAL ..................................................................................................45

SPECIFICATIONS.............................................................................................................46

REGULATORY NOTICES .........................................................................................50

WARRANTY AND RETURN INFORMATION ....................................................................50

LIST OF ILLUSTRATIONS

Figure

Page

In-Ceiling Components ...................................................................................... 5

Back Box Parts ..................................................................................................5

Pendant Components ........................................................................................ 6

Compass Tool ....................................................................................................8

Conduit Fitting Installation ..................................................................................8

Installing Back Box .............................................................................................9

Fastening Back Box ...........................................................................................9

Wiring Diagram for Spectra II™ ........................................................................10

Wiring Diagram for Spectra Lite™ .................................................................... 11

Interconnect Door .............................................................................................12

Transformer .......................................................................................................13

Interconnect Circuit Board Electrical Connections for Spectra II™................... 13

Interconnect Circuit Board Electrical Connections for Spectra Lite™ ...............14

Switch Locations ...............................................................................................15

Lower Dome Installation, In-Ceiling Models ......................................................21

Lower Dome Installation, Pendant Models .......................................................22

Backlight ...........................................................................................................29

SD5 Series Dimension Drawing ........................................................................47

LIST OF TABLES

Table

Page

Video Coaxial Cable Wiring Distances.............................................................. 11

24 VAC Wiring Distances ..................................................................................12

Switch Settings for SW1 ...................................................................................15

Switch Settings for SW2 – P-Type Control .......................................................16

Switch Settings for SW2 – D-Type Control .......................................................17

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

GENERAL

IMPORTANT SAFEGUARDS AND WARNINGS

Prior to installation and use of this product, the following WARNINGS should be observed.

1. Installation and servicing should only be done by qualified service personnel and

conform to all local codes.

2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P

enclosure, it is designed for indoor use only and it must not be installed where

exposed to rain and moisture.

3. Only use replacement parts recommended by Pelco.

4. After replacement/repair of this unit’s electrical components, conduct a resistance

measurement between line and exposed parts to verify the exposed parts have not

been connected to line circuitry.

5. The installation method and materials should be capable of supporting four times the

weight of the enclosure, pan/tilt, camera and lens combination.

The product and/or manual may bear the following marks:

This symbol indicates that

dangerous voltage constituting a

risk of electric shock is present

within this unit.

CAUTION:

RISK OF ELECTRIC SHOCK.

This symbol indicates that there

DO NOT OPEN.

are important operating and

maintenance instructions in the

literature accompanying this unit.

Please thoroughly familiarize yourself with the information in this manual prior to installation

and operation.

MEASURES DE SECURITE IMPORTANTES

Avant d’installer ou d’utiliser ce produit, les mesures de sécurité suivantes sont à prendre:

1. Toute installation et réparation devraient être entreprises par un technicien qualifié et

conformes au codes locaux.

2. A moins que cet equipement indique avoir un boitié agrée NEMA de type 3, 3R, 3S, 4,

4X, 6 ou 6P, il est uniquement conçu pour utilisation intérieure et ne peut donc pas

être en contact de pluie ou d’humidité.

3. Utiliser seulement les pièces de rechanges recommandées par Pelco.

4. Après toute installation ou réparation de la partie électrique de ce produit, une

résistance entre le courant et la partie exposée devrait être installée afin de vérifier

que la partie électrique n’aie pas été en contact d’un court circuit.

5. L’installation entreprise et le matériel utilisé devraient supporter quatre fois le poids du

boitié, de la tourelle, de la caméra, et de la lentille.

Ce produit et/ou le manuel pourrait inclurent les symbols suivants:

Ce symbol indique qu’un voltage

dangereux pouvant provoquer un

chock électrique est présant

dans cette unité.

CAUTION:

RISQUE DE CHOQUE ÉLECTRIQUE.

Ce symbol indique qu’il y a des

mesures d’installation et

NE PAS OUVRIR.

d’entretient importantes inclus

dans le manuel de cet équipement.

Nous vous prions de bien vous familiarisez avec la manuel avant d’entreprendre toute

installation.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

IN-CEILING MODELS

The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes, plus

the C1487M-C system manual that covers everything in the system (back box, dome drive,

and lower dome). Inspect each box to make sure all parts are present.

Back Box

Back box

Parts bag (refer to Figure 2)

Conduit fitting

Safety chain bracket

Lock nut

Compass tool

T-rail clip (clip, L-bracket, screw, lock washer and nut)

Installation/Operation Manual (C1488M-B)

Dome Drive

Dome drive

Installation/Operation Manual (C1489M-A for Spectra II™ or C1498M-A for Spectra Lite™)

Lower Dome

Acrylic lower dome with trim ring

Installation Instructions (C1457M-B)

BACK

BOX

COMPASS TOOL

SAFETY

BRACKET

DOME

DRIVE

CONDUIT FITTING

& LOCK NUT

LOWER

DOME

T-RAIL CLIP

Figure 1. In-Ceiling Components

Figure 2. Back Box Parts

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

PENDANT MODELS

The Spectra II™ dome and Spectra Lite™ dome shipping cartons contain three boxes, plus

the C1487M-C system manual that covers everything in the system (back box, dome drive,

and lower dome). Inspect each box to make sure all parts are present.

Back Box

Back box

Tube of pipe sealant

Installation/Operation Manual (C1488M-B)

Dome Drive

Dome drive

Installation/Operation Manual (C1489M-A for Spectra II™ or C1498M-A for Spectra Lite™)

Lower Dome

Acrylic lower dome with trim ring

Parts bag

O-ring

O-ring lubricant

Screw, 6-32 x 1/4" (black) or 6-32 x 5/16" (gray)

Tube of Loctite^®

Installation Instructions (C1457M-B)

BACK

BOX

DOME

DRIVE

LOWER

DOME

Figure 3. Pendant Components

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

DESCRIPTION

Spectra II™ and Spectra Lite™ domes are capable of the following:

•

360° pan rotation

+2 to -92° tilt

•

preset positioning

variable speed

The in-ceiling models can be installed in hard ceilings or standard 2' x 2' (61 cm x 61 cm)

suspended ceilings. These models are for indoor installation only.

The pendant models can be installed indoors or outdoors. The outdoor models include a

sun shield and heater. The heater allows operation in temperatures down to -60°F (-51°C).

An integral receiver has a switch to select the type of control. The receiver supports

Coaxitron^®and RS-422 control types.

The dome drive quickly disconnects from the back box for easy servicing or moving.

Spectra II™ models include either a high-resolution color or monochrome camera with a

16X optical, 8X electronic zoom lens for a total zoom ratio of 128X. Spectra Lite™ models

include a preset focus color CCD camera with a 12X zoom lens.

Spectra II™ models include additional features–such as zones, patterns, alarms, auxiliary

relays, and auto focus–that are not part of Spectra Lite™ models.

The Spectra II™ and Spectra Lite™ domes operate on 24 VAC.

MODELS

Each Spectra II™ and Spectra Lite™ system consists of one each: back box, dome drive,

and lower dome. Outdoor pendant systems include a sun shield and heater. Refer to

components below (in-ceiling or pendant) to determine your system configuration.

SPECTRA II™ PENDANT COMPONENTS

BB5A-PB

BB5A-PG

Black pendant-mount back box (CE, UL, cUL)

Light gray pendant-mount back box (CE, UL, cUL)

BB5A-PG-E Same as BB5A-PG except includes heater and sun shield (CE, UL, cUL)

DD5AC

DD5AC-X

DD5AM

Dome drive with color camera/lens, NTSC standard (FCC, UL, cUL)

Dome drive with color camera/lens, PAL standard (CE)

Dome drive with monochrome camera/lens, EIA standard (FCC, UL, cUL)

Dome drive with monochrome camera/lens, CCIR standard (CE)

Smoked lower dome (1/2 f-stop of light loss) for black pendant-mount dome

Clear lower dome for black pendant-mount dome

Chrome lower dome (2 f-stops of light loss) for black pendant-mount dome

Gold lower dome (2 f-stops of light loss) for black pendant-mount dome

Smoked lower dome (1/2 f-stop of light loss) for light gray pendant-mount dome

Clear lower dome for light gray pendant-mount dome

Chrome lower dome (2 f-stops of light loss) for light gray pendant-mount dome

Gold lower dome (2 f-stops of light loss) for light gray pendant-mount dome

Same as LD5PG-0 except includes heater

DD5AM-X

LD5PB-0

LD5PB-1

LD5PB-2

LD5PB-3

LD5PG-0

LD5PG-1

LD5PG-2

LD5PG-3

LD5PG-E0

LD5PG-E1

LD5PG-E2

LD5PG-E3

Same as LD5PG-1 except includes heater

Same as LD5PG-2 except includes heater

Same as LD5PG-3 except includes heater

SPECTRA II™ IN-CEILING COMPONENTS

BB5A-F

DD5AC

DD5AC-X

DD5AM

DD5AM-X

LD5F-0

LD5F-1

LD5F-2

LD5F-3

Indoor back box for flush mounting in a ceiling (CE, UL, cUL)

Dome drive with color camera/lens, NTSC standard (FCC, UL, cUL)

Dome drive with color camera/lens, PAL standard (CE)

Dome drive with monochrome camera/lens, EIA standard (FCC, UL, cUL)

Dome drive with monochrome camera/lens, CCIR standard (CE)

Smoked lower dome (1/2 f-stop of light loss)

Clear lower dome

Chrome lower dome (2 f-stops of light loss)

Gold lower dome (2 f-stops of light loss)

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECTRA LITE™ PENDANT COMPONENTS

BB5T-PB

BB5T-PG

Black pendant-mount back box (CE, UL, cUL)

Light gray pendant-mount back box (CE, UL, cUL)

BB5T-PG-E Same as BB5T-PG except includes heater and sun shield (CE, UL, cUL)

DD5T-C

Dome drive with color camera and lens, NTSC standard (FCC, UL, cUL)

Dome drive with color camera and lens, PAL standard (CE)

Smoked lower dome (1/2 f-stop of light loss) for light gray pendant-mount dome

Clear lower dome for light gray pendant-mount dome

Chrome lower dome (2 f-stops of light loss) for light gray pendant-mount dome

Gold lower dome (2 f-stops of light loss) for light gray pendant-mount dome

Same as LD5PG-0 except includes heater

DD5T-C-X

LD5PG-0

LD5PG-1

LD5PG-2

LD5PG-3

LD5PG-E0

LD5PG-E1

Same as LD5PG-1 except includes heater

SPECTRA LITE™ IN-CEILING COMPONENTS

BB5T-F

DD5T-C

DD5T-C-X

LD5F-0

LD5F-1

LD5F-2

LD5F-3

Indoor back box for flush mounting in a ceiling (CE, UL, cUL)

Dome drive with color camera and lens, NTSC standard (FCC, UL, cUL)

Dome drive with color camera and lens, PAL standard (CE)

Smoked lower dome (1/2 f-stop of light loss)

Clear lower dome

Chrome lower dome (2 f-stops of light loss)

Gold lower dome (2 f-stops of light loss)

INSTALLATION FOR IN-CEILING MODELS

To install the dome proceed through the steps in this section, beginning with the Ceiling and

Back Box Preparation section.

CEILING AND BACK BOX PREPARATION

HARD CEILING

NOTE: Use the SCA1

(structural ceiling adapter) if

additional support is required.

1. Locate the center point where you want to drill a hole in the ceiling. (The ceiling tile

cannot be thinner than 0.50 inch [1.27 cm] nor thicker than 1.75 inches [4.45 cm].)

2. Drill a hole in the ceiling using a 3/32-inch drill bit.

3. Remove the compass tool from the parts bag that came with the back box (refer to

Figure 4). Press the stud of the compass tool into the hole in the ceiling. Insert a pencil

in the hole in the other end of the compass and mark a circle on the ceiling.

CAUTION: Be

careful not to cut

outside of the line.

4. Carefully cut the circle out of the ceiling.

If you do, you may not be

able to install the back box.

Also, the trim ring may not

cover the hole.

5. Remove the conduit fitting, lock nut, and safety chain bracket from the parts bag and

attach them to the back box as shown in Figure 5.

Proceed to the Wiring section.

ATTACH SAFETY CHAIN HERE

Figure 4. Compass Tool

Figure 5. Conduit Fitting Installation

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

SUSPENDED CEILING

1. Remove the ceiling tile from the ceiling. (The ceiling tile cannot be thinner than 0.50

inch [1.27 cm] nor thicker than 1.75 inches [4.45 cm].)

CAUTION: The

ceiling tile must be

capable of support-

2. Locate the center point to drill a hole in the tile.

ing 16 pounds (7.3 kg) of

weight. If the ceiling tile will

not support this weight, or-

der the SD5-P metal panel.

3. Drill a hole in the ceiling tile using a 3/32-inch drill bit.

4. Remove the compass tool from the parts bag that came with the back box (refer to

Figure 4). Press the stud of the compass tool into the hole in the ceiling. Insert a pencil

in the hole in the other end of the compass and mark a circle on the ceiling.

CAUTION: Be

careful not to cut

outside of the line.

5. Carefully cut the circle out of the ceiling tile.

If you do, you may not be

able to install the back box.

Also, the trim ring may not

cover the hole.

6. Remove the conduit fitting, lock nut, and safety chain bracket from the parts bag and

attach them to the back box as shown in Figure 5.

7. Refer to Figure 6. Compress the spring clips on the back box with your hands and

push the back box through the hole in the ceiling tile. The spring clips will spring out

when they clear the ceiling tile.

8. Refer to Figure 7. Tighten the screws until the spring clips hold the back box firmly to

the ceiling tile. You will hear a clicking noise when the screws are tight. Do not install

the ceiling tile in the ceiling yet.

Proceed to the Wiring section.

HARD CEILING

CEILING TILE

Figure 6. Installing Back Box

HARD CEILING

CEILING TILE

T-RAIL CLIP

FOR

CEILING TILE

T-RAIL CLIP

FOR

CEILING TILE

Figure 7. Fastening Back Box

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

WIRING

Bring wiring to the back box opening in the ceiling. Do not attach the wiring to the back box.

You will do that later.

Refer to Figure 8 for the Spectra II™ wiring diagram or Figure 9 for the Spectra Lite™

wiring diagram.

Wiring is required for power, earth ground, and video.

Refer to Table A for the type of video coaxial cable to use.

Input power for the dome is 24 VAC only. Power consumption is 30 vA per dome for indoor

models and 75 vA for outdoor models. Refer to Table B to determine the size of wire to use.

NOTE: The dome will stop

operating if the voltage at

the dome drops below 18

VAC. It will turn back on

when the voltage exceeds

18 VAC.

Use a 24 VAC transformer with the following minimum vA:

40 vA per dome

100 vA per dome

For indoor models (without heater)

For outdoor models (with heater)

Refer to Figure 11 for wiring multiple domes from the same transformer.

SPECTRA II™ INTERCONNECT BOARD

CONTROL

(RS-422)

+5 to +24 VDC

EXTERNAL RELAY

(WIRING EXAMPLE)

Figure 8. Wiring Diagram for Spectra II™

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

If you are using a Coaxitron^®controller, the control signals to operate the dome drive will

be transmitted over the video coax. The RS-422 control lines are not used.

If you are not using a Coaxitron^®controller, use the RS-422 control lines. Use 22-gauge

wire.

Optional wiring for the Spectra II™ dome may be provided for alarm inputs (maximum of

seven), relay output (Aux 1), and auxiliary output (Aux 2). For more information about

wiring requirements, refer to the Back Box Connections section.

Proceed to the Back Box Installation section.

SPECTRA LITE™ INTERCONNECT BOARD

CONTROL

(RS-422)

Figure 9. Wiring Diagram for Spectra Lite™

Table A. Video Coaxial Cable Wiring Distances

Cable Type*

Maximum Distance

RG59/U

RG6/U

RG11/U

750 ft (229 m)

1,000 ft (305 m)

1,500 ft (457 m)

* Minimum cable requirements:

75 ohms impedance. All-copper center conductor.

95% braided copper shield.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table B. 24 VAC Wiring Distances

The following are the recommended maximum distances for 24 VAC with a 10-percent

voltage drop. (Ten percent is generally the maximum allowable voltage drop for AC-powered

devices.)

Wire Gauge

30 vA

75 vA

94 ft

(28 m)

150 ft

(45 m) (72 m)

238 ft

380 ft

603 ft

960 ft

(115 m) (183 m) (292 m)

37 ft

(11 m)

60 ft 95 ft

(18 m) (29 m)

152 ft

(46 m)

241 ft

(73 m) (117 m)

384 ft

BACK BOX INSTALLATION

OPTIONAL PROCEDURE:

If you prefer, you may make

the wiring connections in-

side the back box before

installing the back box in the

ceiling.

1. Suspended Ceiling Only (for hard ceiling, go to step 2) – Install the ceiling

tile with the back box. Attach a T-rail clip on each side of the ceiling tile as shown in

Figure 7.

The clips for the ceiling tile are supplied with the back box. Attach the clip to the T-rail.

Fasten the L-bracket to the clip with the supplied screw, lock washer and nut.

2. Install a safety chain or cable (not supplied) that will support up to 16 pounds (7.3 kg).

Fasten one end to a support structure in the ceiling. Fasten the other end to the safety

chain bracket (refer to Figure 5) to prevent the back box from falling.

To do this, loosen the

thumbscrew inside the back

box and open the hinged

door (refer to Figure 10).

Bring the wiring into the

back box through the con-

duit fitting. Follow the steps

in the Back Box Connec-

tions section and then

3. Refer to Figure 10. Loosen the thumbscrew inside the back box and open the hinged

door.

4. Bring the wiring into the back box through the conduit fitting. If the wiring is inside

flexible conduit, connect the conduit to the fitting on the back box.

return to this section.

5. Hard Ceiling Only - Refer to Figure 6. Compress the spring clips on the back box

with your hands and push the back box through the hole in the ceiling. The spring clips

will spring out when they clear the ceiling. Refer to Figure 7. Tighten the screws until

the spring clips hold the back box firmly to the ceiling. You will hear a clicking noise

when the screws are tight.

CAUTION: The

ceiling must be ca-

pable of supporting

16 pounds (7.3 kg) of

Proceed to the Back Box Connections section.

weight. If the ceiling will not

support this weight, provide

additional reinforcement.

Also, a suitable safety chain

must be attached to the

back box to support up to 16

pounds (7.3 kg) in the event

of a ceiling failure.

THUMBSCREW

00096

Figure 10. Interconnect Door

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

BACK BOX CONNECTIONS

WARNING: Make sure you

wire power to the outer con-

nectors of the terminal block

and ground to the middle

connector. Otherwise, you

could damage the dome.

Refer to Figure 12 or 13 to attach the wiring to the interconnect circuit board inside the back

box. Also refer to Figure 8 or 9 if necessary.

1. Earth Ground - Connect earth ground to the middle connector on the power

connector.

2. Power - Connect 24 VAC from the transformer to the outer terminals on the power

connector. It does not matter which lead goes to which terminal.

If you are wiring more than one dome from the same transformer, it is important to

wire the power connector in each dome the same way. That is, the wiring from one

side of the transformer must be connected to the same connector on each dome. If

you reverse the wiring, the cameras will be out of phase with each other and may

produce what appears to be vertical roll when switching between cameras. Refer to

Figure 11 for a wiring diagram.

DOME 1

POWER

DOME 2

POWER

3. Video - Connect the coaxial cable to the BNC video connector.

4. Control - If you are using a Coaxitron^®controller, control signals will be transmitted

DOME 3

POWER

over the video coax.

If you are using RS-422 (P or D) control signals, connect the control lines from the

controller to the circuit board. Connect the wires as follows:

EXAMPLE: If each dome

requires 30 vA, three domes

require a transformer with a

minimum output of 120 vA

(refer to the Wiring section

for transformer require-

ments).

From controller

To 4-Wire terminal on circuit board

RX-

RX+

TX-

TX+

RX-

RX+

TX+

Figure 11. Transformer

Wiring

CONNECTOR

FOR OPTIONAL

TRANSLATOR

SUBASSEMBLY

HTR/FAN

VIDEO

RS-422

CONTROL

SIGNALS

RX–

RX+

TX–

TX+

DOME DRIVE

CONNECTOR

GND

COM

AUX 2

GND

AUX 1

FUSE

FAN

24 VAC

MIDDLE

PIN IS

GND

POWER

(24 VAC ONLY)

1.6 A

Figure 12. Interconnect Circuit Board Electrical Connections for Spectra II™

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

CONNECTOR

FOR OPTIONAL

TRANSLATOR

SUBASSEMBLY

HTR/FAN

VIDEO

RS-422

CONTROL

SIGNALS

RX–

RX+

TX–

TX+

DOME DRIVE

CONNECTOR

FUSE

FAN

24 VAC

MIDDLE

PIN IS

GND

POWER

(24 VAC ONLY)

1.6 A

Figure 13. Interconnect Circuit Board Electrical Connections for Spectra Lite™

NOTE: (Spectra II™

Only) Connect only a low

voltage device to the relay

output. Maximum current

rating of the relay contacts

is two amperes.

5. Heater/Fan - This is a factory connection for a heater on outdoor pendant models.

6. Alarm Inputs - (Spectra II™ Only) If you need alarm inputs, connect them. The

maximum number of alarm inputs is seven. Refer to Figure 8 for a typical wiring

example. Alarm inputs require a ground signal through a contact closure, such as a

switch.

7. AUX 1 - (Spectra II™ Only) An AUX 1 command from the controller will activate

the relay output. If you need the relay, wire it as required. Refer to Figure 8. The relay

contacts are shown when AUX 1 is inactive. When an AUX 1 command is issued, the

relay contacts will reverse and remain latched until a clear command is issued.

CAUTION:

(Spectra II™

Only) The maxi-

mum output of AUX 2 is 150

mA. If you connect a device

that draws more current,

you could destroy the output

transistor. The output is in-

tended to drive logic circuits

or low-current devices. If

higher current is required,

connect the output to a relay.

8. AUX 2 - (Spectra II™ Only) An AUX 2 command from the controller will place a

ground at the output of AUX 2 to operate the device connected to it. The output will

remain latched until a clear command is issued. If you need the AUX 2 output, wire it

as required. Refer to Figure 8 for typical wiring examples. The AUX 2 output is an

open collector transistor driver that can pass a maximum of 150 mA at 32 VDC. It is

capable of driving TTL logic circuits or low-current reed relays. If you use an external

relay, make sure that both the supply voltage and the current requirements are well

below the maximum of 32 VDC and 150 mA. Exceeding these values will cause

permanent damage to the dome. If you are not familiar with open collector drive

requirements, contact Pelco technical support for assistance.

CAUTION: Leave

adequate slack in

the wiring to permit

9. Close the door and tighten the thumbscrew securely.

Proceed to the Dome Drive section.

the door to open without

pulling on the connectors.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

DOME DRIVE

NOTE: For Coaxitron^®con-

trol, SW2 is not used and all

switches must be OFF.

1. Turn on power to the back box. The red LED should light to indicate power.

If the LED does not light, correct the trouble before proceeding. Refer to the Trouble-

shooting section.

If the light is operating, you may either leave the power on and continue with the

installation, or you may turn the power off before proceeding further.

2. Set the switches on the bottom of the dome drive. Refer to Figure 14 and Table C for

the settings for SW1.

Refer to Figure 14 and Tables D and E for the settings for SW2.

CAUTION: Make

sure the dome

drive locks into

3. Install the dome drive in the back box: Line up the green drive eject tab on the dome

drive with the green label on the back box and the red static tab with the red label on

the back box. Raise the dome drive into the back box and push on the ends of the

tabs until they both click into place on the back box.

place. Tug downward on the

dome drive with moderate

pressure to ensure that it

stays in place.

4. Turn on power, if it is not on. Listen for the fan operating. If the fan does not work, the

dome will overheat and shut down. If the fan does not work, return the back box

electronic assembly and dome drive to the factory for repair. Refer to the Back Box

Electronic Assembly Removal section.

Proceed to the Lower Dome section.

SW 1

OFF

SW 1

SW 2

1 2 3 4 5 6 7 8

OFF

1 2 3 4 5 6 7 8

SW 2

OFF

Figure 14. Switch Locations

Table C. Switch Settings for SW1

Control Type

Switch Setting

SW1-1

SW1-2

SW1-3

SW1-4

SW1-5

SW1-6

SW1-7

SW1-8

Coaxitron^®

P-Type Control

D-Type Control

OFF

OFF*

OFF**

NOTES: Switches SW 1-3 through SW 1-6 MUST be OFF.

D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500 and CM8500

controllers or with American Dynamics control systems using the AD2083 Translator.

P-type control is RS-422 that is compatible with Pelco’s CM6700/CM9750/CM9760 control systems.

* OFF- Use with controllers that have more than 32 presets.

ON- Use with American Dynamics controllers (32 presets).

** OFF - Use with all control systems except CM9502 with variable speed keyboards.

For CM9502 with fixed speed keyboards, set switch OFF.

ON - Use with CM9502 with variable speed keyboards for smoother joystick control.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table D. Switch Settings for SW2 – P-Type Control

NOTES: For Coaxitron^®controls, all switches on SW2 MUST be OFF.

For D-type control systems, refer to Table E.

Receiver Address

Switch Setting

SW2-3

SW2-1

SW2-2

SW2-4

SW2-5

OFF

Baud Rate

Switch Setting

SW2-6

SW2-7

SW2-8

2400

4800

9600

OFF

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control

NOTES: For Coaxitron^®controls, all switches on SW2 MUST be OFF.

For P-type control systems, refer to Table D.

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

Continued on next page

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

OFF

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

OFF

Continued on next page

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 – D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

170

171

172

173

174

175

176

OFF

Continued on next page

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 - D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3 SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

177

178

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

195

196

197

198

199

200

201

202

203

204

205

206

207

208

209

210

211

212

213

214

215

216

217

218

219

220

221

222

223

224

225

226

227

228

229

230

231

232

233

234

235

236

OFF

Continued on next page

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Table E. Switch Settings for SW2 - D-Type Control (continued)

Receiver Address

Switch Setting

SW2-1 SW2-2 SW2-3

SW2-4 SW2-5 SW2-6 SW2-7 SW2-8

237

238

239

240

241

242

243

244

245

246

247

248

249

250

251

252

253

254

OFF

LOWER DOME

1. Snap the clip on the end of the trim ring leash into the hole on the lip of the back box

next to one of the mounting screws.

2. Line up the snaps on the trim ring with the mounting screws on the back box. Snap the

trim ring into place on the plastic snap washers on the mounting screws.

Figure 15. Lower Dome Installation, In-Ceiling Models

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION FOR PENDANT MODELS

PENDANT-MOUNT INSTALLATION

1. Install the pendant dome mount. Refer to the instructions supplied with the mount. If

the mount is outdoors, make sure it is properly sealed to keep moisture out.

2. Bring the wiring for the dome through the mount. Refer to the Wiring section.

3. Refer to Figure 10. Loosen the thumbscrew inside the back box and open the hinged

door.

4. Screw the back box into the mount and bring the wiring into the back box. If outdoors,

apply the provided pipe sealant to the threads on the back box.

5. Attach the wiring to the back box. Refer to the Back Box Connections section.

6. Install the dome drive. Refer to the Dome Drive section.

NOTE: If outdoors, apply

Duct Seal inside the pipe

portion of the back box to

prevent moisture or cold air

inside the mount from enter-

ing the unit and causing

condensation on the dome.

Make sure no moisture has

condensed inside the unit

before installing the lower

dome. Duct Seal can be

purchased through local

electrical supply houses.

7. Remove the O-ring and O-ring lubricant from the parts bag. Lightly apply lubricant to

the O-ring so that it is just moistened; do not use excess lubricant. Install the O-ring in

the groove on the trim ring of the lower dome.

8. Refer to Figure 16. Hanging down from the back box is a short cable (the trim ring

leash). Hold up the lower dome near the back box so that the trim ring leash touches

the lower dome. Line up the two screw holes in the trim ring of the lower dome with

the two screw holes in the back box. Place a finger on the edge of the trim ring where

the leash touches the lower dome.

9. Look inside the lower dome and note which of the six retainer screws is closest to your

finger. Remove this screw and attach the trim ring leash to the screw. Reinstall the

screw securely and make sure the leash will hold the lower dome.

LEASH

SCREW HOLES

(FRONT & BACK)

ATTACH LEASH

TO NEAREST

RETAINER

SCREW

Figure 16. Lower Dome Installation, Pendant Models

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

10. If you are installing an outdoor model, plug the two-pin heater connection in the lower

dome into the mating connector in the back box.

11. Remove the two screws and the tube of Loctite^®from the parts bag. Apply a drop of

Loctite^®to each screw.

12. Push the lower dome inside the back box, line up the screw holes, and install the two

screws.

SURFACE-MOUNT INSTALLATION

1. Use a hole saw to drill a hole in the ceiling where you want to hang the pendant dome.

2. Bring the wiring for the dome to the opening. Refer to the Wiring section.

NOTE: For hard ceilings,

such as concrete, where the

wiring must be installed in

surface-mounted conduit, use

the optional BB5-PCA-BK

(black) or BB5-PCA-GY

(gray) Pendant Conduit

Adapter.

3. Refer to Figure 10. Loosen the thumbscrew inside the back box and open the hinged

door.

4. Remove the gasket and the top mount from the back box by taking out the three

screws and lock washers.

5. Attach the back box to the ceiling using #8 hardware (not supplied).

6. Attach the wiring to the back box. Refer to the Back Box Connections section.

7. Install the dome drive. Refer to the Dome Drive section.

8. Remove the O-ring and O-ring lubricant from the parts bag. Apply lubricant to the

O-ring. Install the O-ring in the groove on the trim ring of the lower dome.

9. Refer to Figure 16. Hanging down from the back box is a short cable (the trim ring

leash). Hold up the lower dome near the back box so that the trim ring leash touches

the lower dome. Line up the two screw holes in the trim ring of the lower dome with

the two screw holes in the back box. Place a finger on the edge of the trim ring where

the leash touches the lower dome.

10. Look inside the lower dome and note which of the six retainer screws is closest to your

finger. Remove this screw and attach the trim ring leash to the screw. Reinstall the

screw securely and make sure the leash will hold the lower dome.

11. If you are installing an outdoor model, plug the two-pin heater connection in the lower

dome into the mating connector in the back box.

12. Remove the two screws and the tube of Loctite^®from the parts bag. Apply a drop of

Loctite^®to each screw.

13. Push the lower dome inside the back box, line up the screw holes, and install the two

screws.

OPERATION

The red LED in the interconnect door in the back box lights when power is turned on and

the fan operates to exhaust heat from inside the back box.

If you have an outdoor pendant model with a heater, the heater elements in the back box

turn on at 70°F (21°C) and turn off at 85°F (29°C). The heater element in the lower dome

turns on at 40°F (4°C) and turns off at 60°F (16°C). The fans in the back box operate

continuously.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

POWER-UP DISPLAY

When the Spectra II™ dome or Spectra Lite™ dome is powered up or reset, the selected

protocol, revision number, and other information is displayed on the monitor. For example,

the screen might show the following information:

PELCO SPECT II 4.0

CONFIGURE DONE

Protocol C

NOTE: The dome will stop

operating if the voltage at

the dome drops below 18

VAC. It will turn back on and

go through its start-up rou-

tine when the voltage ex-

ceeds 18 VAC.

The information remains on the monitor until the dome is moved. The information displayed

depends on the selected protocol and the choice made on the menu for selectable power-

up mode, a feature that lets the dome resume a desired condition upon power-up. As a

default, the dome goes to a random position. (Refer to the Power-Up Mode section).

The control system protocol (C, D, or P) appears. C is for Pelco’s Coaxitron^®control

systems. D-type control is RS-422 that is compatible with Pelco’s CM6700, MPT9500 and

CM8500 controllers or with American Dynamics control systems using the AD2083

Translator. P-type control is RS-422 that is compatible with Pelco’s CM6700 and CM9750/

CM9760 control systems.

For the D and P protocols, the device address, baud rate, parity (N), number of data bits

(8), and number of stop bits (1) appears. For the D protocol, if the mode for 32 presets is

selected (SW1-7 is ON), “32 presets” appears.

If the CM9500 mode is selected (SW1-8 is ON), “CM9500 mode” appears.

PAN AND TILT FUNCTIONS

Use the joystick on your controller to control pan and tilt functions.

Pan and tilt operation is at a fixed speed with fixed-speed controllers. The speed is

determined by the controller.

Standard pan operation with variable-speed controllers will range from 0.5 to 80 degrees

per second, depending on the position of the joystick. In the turbo mode, pan speed will be

150 degrees per second. When performing preset operations, pan speed will be 250

degrees per second.

Standard tilt operation with variable-speed controllers will range from 0.5 to 40 degrees per

second, depending on the position of the joystick. When performing preset operations, tilt

speed will be 200 degrees per second. Turbo mode does not affect the tilt speed.

(Spectra II™ Only) If the proportional pan mode is enabled (refer to the Proportional

Pan section), the pan (and tilt) speed will depend on the amount of zoom. At telephoto

zoom settings, the pan (and tilt) speeds will be slower for a given amount of joystick

deflection than at wide zoom settings. This keeps the image from moving too fast on the

monitor when there is a large amount of zoom. This slowing does not happen when going

to a preset, but does occur in turbo mode when high zoom is selected.

AUTO FLIP

When the camera tilts downward and goes just beyond the vertical position, the dome

rotates 180 degrees. When the dome rotates (flips), the camera starts moving upward as

long as you continue to hold the joystick in the down position. Once you let go of the

joystick after the dome rotates, joystick control returns to normal operation. The auto-flip

feature is useful for following a person who passes directly beneath the camera.

You can disable this feature in the auto flip programming menu. Refer to Auto Flip in the

Programming the Spectra II™ and Spectra Lite™ section.

SCAN SPEED

Scan speed is adjustable from 1 to 40 degrees per second through the programming menu.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

ZOOM

SPECTRA II™ ZOOM

NOTE: (Spectra II™

The Spectra II™ dome can magnify an object up to 128 times. The dome has 16X of optical

zoom and 8X of electronic (digital) zoom for 128X total zoom. The amount of zoom can be

set for 16X, 32X, 64X, or 128X. Software controls the amount of zoom. Refer to the Zoom

Limit section to program the zoom limits.

Only) On some controllers

the zoom speed can be

changed. Refer to the docu-

mentation for your controller.

16X or 32X Zoom

Press the Zoom Tele button to magnify an object up to 16 or 32 times. Hold down the

button until you have the picture you want.

64X or 128X Zoom

1. Press the Zoom Tele button until the picture reaches 32X zoom.

2. Release the button.

3. Within one second, press the button again until you have the picture you want.

Zoom Wide

Press the Zoom Wide button to increase the field of view.

SPECTRA LITE™ ZOOM

The Spectra Lite™ dome can magnify an object up to 12 times (the dome has 12X of

optical zoom).

Zoom Telephoto - Press and hold down the Zoom Tele button until you have the picture

you want.

Zoom Wide - Press the Zoom Wide button to increase the field of view.

PRESET FUNCTIONS

NOTE: For American

The Spectra II™ dome is capable of going to 64 preset locations, each with a 20-character

label. The presets are numbered 1-32 and 35-66. The Spectra Lite™ dome can go to 32

presets. The presets are numbered 1-32.

Dynamics controllers with

only 32 presets, set switch

SW1-7 on the dome drive in

the ON position. When

SW1-7 is ON, preset

Refer to the documentation for your control system for programming presets.

When a preset operation is performed, the amount of error in moving to the pan and tilt

position is 1/2 degree. If you command the dome to go to an undefined preset, erratic

operation may result.

99 becomes 32

98 becomes 31

97 becomes 30

96 becomes 29

95 becomes 28

93 becomes 26

92 becomes 25

91 becomes 24

90 becomes 23

Presets 33 and 34 are fixed commands, meaning that you cannot program them. Preset 33

is the “flip” command, which will pan the dome drive 180 degrees from the position it is at.

Preset 34 is the “pan zero” command, which will direct the dome drive to the factory-

determined zero reference point.

The following presets are reserved for special functions. (An asterisk denotes

presets that apply to Spectra II only.)

If the limit stops are turned

off (refer to the Limit Stops

section), presets 23-26 can

be used as regular presets.

Preset

Function

Park

1-7*

90-93

Alarms, if used

Flip command

Pan zero command

Limit stops

Select camera programming menu

Stop a scan

97-99

Activate scanning

In the following sections, sometimes a number in parentheses follows a preset. This second

number is for 32-preset mode (conversion that lets Pelco’s presets work with American

Dynamics controllers). If you are using an American Dynamics controller, use the number in

parentheses.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

RANDOM, FRAME, AND AUTO SCANNING

Program preset 97 (30) to start random scanning. Program preset 98 (31) to activate frame

scanning (three seconds of scanning followed by a three-second pause). Program preset

99 (32) to start auto (continuous) scanning.

Scan limit stops are controlled by software. Refer to the Limit Stops section to program the

scan limit stops.

When the dome reaches a scan limit stop, it will immediately reverse direction.

Program preset 96 (29) to stop a scan. Any pan/tilt or lens command also will stop a scan.

ZONES

(This section applies to Spectra II™ only.)

The Spectra II™ dome is capable of eight zones, each with a 20-character label. Depend-

ing on the controller, you can define the zone size and define any zone as “blanked” for

video when the camera pans into the zone area. If zone labels are turned off, the system

displays the message VIDEO BLANK to indicate the video is being blanked and is not

failing. (Refer to the Zone Blank section for instructions.) For other information on program-

ming zones, refer to the documentation for your control system.

PATTERNS

(This section applies to Spectra II™ only.)

NOTE: Changing the length

erases all stored patterns.

The Spectra II™ dome can do either one full pattern (1.5, 3, or 6 minutes long) or two half

patterns (.75, 1.5, or 3 minutes long). This pattern can consist of any standard pan and tilt

or lens command. Presets, flip, and turbo are not allowed in a pattern. Zone scan can be

enabled while running a pattern.

Refer to the documentation for your control system to program and run patterns.

ALARMS

(This section applies to Spectra II™ only.)

The Spectra II™ dome has seven alarm inputs, which can be designated as either high or

low priority through its programming menu. When an alarm is received, the dome does one

of the following:

•

Moves to the preset position that corresponds to the alarm number. For example, if

alarm 3 is activated, the dome moves to preset 3.

•

Runs a half pattern or full pattern as programmed in the Alarm Pattern submenu.

If any of presets 1-7 are not used for alarms, they can be used as regular presets.

However, if they are being used for alarms, they should not be used for anything else.

If an alarm input is programmed to run a pattern, the corresponding preset can be used as

a regular preset. For example, if alarm 3 is programmed to run a pattern, preset 3 can be

used as a regular preset.

There is no indication at the controller that an alarm has been received, other than the view

displayed on the monitor.

The high priority setting (if set on the programming menu) is significant when more than

one alarm is activated. If priority in alarms is not required, leave all alarms in the low setting.

•

If the activated alarm inputs have the same priority–all low or all high–then the

dome will sequence between the presets that correspond to the alarm numbers.

•

If the activated alarm inputs have different priorities–for example, one is high and

four are low–the dome goes only to the high. It remains fixed on the high and only

goes to the low after the high has been cleared.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

In certain situations, the dome will respond as follows:

•

If a preset has not been set, but an alarm is connected: the dome will go to a factory

preset that will not be the desired position.

If one alarm is a preset and another is a pattern and both are received: the dome will

alternate between them.

An alarm clears by returning to its former (off) state.

Depending on choices made on the programming menu, the dome can respond to an alarm

by running one of the patterns below. (Refer to the Patterns section for more information.)

•

Run full pattern

Run half pattern 1

Run half pattern 2

When sequencing between presets, the dwell time depends on the time set on the Alarm

Dwell submenu for that preset. After the dwell time expires, the dome immediately does

one of the following:

•

If the resume feature was selected on the programming menu and there are no other

alarms activated, the dome resumes its prior activity. So, it might return to its previous

position or resume a scan or pattern.

•

If there are other alarms activated, the dome goes to them.

If you move the joystick to pan or tilt the dome, or if you issue a lens command while there

is an alarm, the pan and tilt or lens command overrides the alarm. Sixty seconds after the

last pan and tilt or lens command, the dome will return to the alarm preset if the alarm is

still active.

AUXILIARY OUTPUTS

(This section applies to Spectra II™ only.)

An AUX 1 command from the controller will activate the relay in the dome and operate the

device that is connected to the relay. The relay will remain latched until a clear command is

issued.

An AUX 2 command from the controller will place a ground at the output of AUX 2 to

operate the device that is connected to it. The output will remain latched until a clear

command is issued. Refer to the Back Box Connections section for precautions regarding

the use of the AUX 2 output.

The output relay can also be programmed so that it is activated when any alarm input is

activated. When latching (toggling) is selected on the programming menu, giving the AUX 1

command from the controller changes the state of the AUX (for example, if it was on, this

turns it off.) The clear command from the controller will turn the AUX off in the latching or

toggle mode.

PARK

If the Spectra II^TMdome does not receive any commands for a specified period of time

(refer to the Park Time Minutes section), the dome will go to preset 1 and park. If the time

specified is zero, or if preset 1 has not been programmed, the dome will not park. The

default is zero minutes.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

PROGRAMMING THE SPECTRA II™ AND SPECTRA LITE™

The Spectra II™ and Spectra Lite™ domes can be programmed for the following functions.

(In this section, an asterisk denotes items that apply to Spectra II only.)

AGC (automatic gain control)

Alarm dwell*

Auto park time

Auxiliary relays*

Backlight compensation

Camera reset

Gain

Limit stops

Power-up mode

Proportional panning*

Scan speed

Alarm pattern*

Alarm priority*

Alarm resume*

Auto flip disable

Auto focus*

Sharpness

Shutter speed

Video zone blanking*

White balance

Zoom limit*

Pattern length*

Power line synchronization*

Auto iris

The main menu contains six secondary menus for Spectra II™ and three for Spectra Lite™.

•

Camera

Line Sync*

Power Up Mode

•

Aux*

Alarms, Zone Blank*

Other

Each secondary menu has submenus, which are structured as shown below.

1. Camera

First Camera Submenu

Backlight comp

Zoom limit*

Reset camera

Gain/AGC

Second Camera Submenu

Shutter speed

Auto focus mode*

Sharpness

Auto sharpness

Sharpness

AGC mode

Gain

White balance

Auto-iris

Auto white bal

Auto-iris mode

Auto-iris level

Auto-iris peak

Next (to second camera submenu)

R-B white bal

M-G white bal

Prev (to first camera submenu)

2. Line Sync*

Line sync*

Line sync phase*

3. Power Up

Power Up

4. Aux*

Aux 1 mode*

Aux 2 mode*

5. Alarm, Zone Blank*

Alarm resume*

Alarm dwell sec*

Alarm priority*

Alarm pattern*

Zone blank*

6. Other

Auto flip

Proportional pan*

Limit stops

Park time minutes

Scan speed deg/s

Pattern length*

The following sections explain how to program the Spectra II™ and Spectra Lite™ domes

using the menu choices.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

MAIN MENU ACCESS

You can call up the main menu on your monitor by programming (setting or creating) preset

95 (28 if in 32-preset mode; refer to the Preset Functions section).

Programming preset 95 for Pelco’s controllers varies according to the type of controller you

are using. Instructions for programming preset 95 are given below for various Pelco

controllers.

CM6700

1. Enter the number of the Spectra II™ or Spectra Lite™ camera and press the CAM key.

2. Enter 95 and hold the PRESET key for two seconds.

3. In the Edit Preset menu, arrow to SET and press the ACK key. The main menu appears.

CM8500

1. Enter the number of the Spectra II™ or Spectra Lite™ camera and press the CAM key.

2. Highlight PRESET in the Camera menu and hold down the joystick button until the Set

Presets prompt appears.

3. Enter 95 and press the PRESET key. The main menu appears.

CM9500

1. Enter the number of the Spectra II™ or Spectra Lite™ camera and press the CAM key.

2. Press the SELECT key twice.

3. Highlight CAM in the Setup menu and press the SELECT key.

4. Highlight PRESET in the Camera menu and press the SELECT key.

5. Enter 95 and press the F1 key. The main menu appears.

CM9750

1. Turn the KEY SWITCH to the ON position.

2. Press the PROG key. PROGRAM appears on the LCD display.

3. Press the PRES key. The PRESET prompt appears.

4. Enter 95 and press the ENTER key. The main menu appears.

5. Turn the KEY SWITCH to the OFF position.

CM9760

1. In the default menu, select DEF. The Define Submenu appears.

2. Enter your four-digit PIN.

3. Enter 95 and select PRST. The main menu appears on the monitor.

4. Select the Quit icon to return to the default menu.

MPT9500

Standard Coaxitron^®Mode

1. Enter 95 and press the PRESET SET key.

2. Position the asterisk in the YES row and press the F1 key. The main menu appears.

Extended Coaxitron^®or RS-485 Mode

1. Enter 95 and press the PRESET SET key.

2. Press the F2 key. The main menu appears.

BACKLIGHT COMPENSATION

There are two backlight compensation modes: on and off.

NON-SENSITIVE AREA

Backlight compensation allows the Spectra II™ dome to compensate for bright light behind

the object you want to view. With backlight compensation On, the Spectra II™ dome will

use only the center 10 percent of the picture for adjusting the iris (refer to Figure 17). If

there is a bright light source outside of this area, it will wash out to white. The camera will

adjust the iris so that the object in the sensitive area is properly exposed.

SENSITIVE

AREA

To change the backlight compensation mode:

Figure 17. Backlight

1. Program Preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

Compensation

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Backlight Comp.

5. Press the Iris Open button on your keyboard. A star will appear beside Backlight Comp

and the cursor will move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

ZOOM LIMIT

(This section applies to Spectra II™ only.)

The Spectra II™ dome can magnify an object up to 128 times. The dome has 16X of optical

zoom and 8X of electronic (digital) zoom for 128X total zoom. The amount of zoom can be

set for 16X, 32X, 64X, or 128X.

To change the zoom limit:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Zoom Limit.

5. Press the Iris Open button. A star will appear beside Zoom Limit and the cursor will

move to the right beside the current zoom limit.

6. Move the joystick up or down to choose the zoom limit.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

RESET CAMERA

Resetting the camera returns the following settings to their defaults. (An asterisk

denotes items that apply to the Spectra II™ only.)

Setting:

Auto-focus mode*

Default:

Auto*

Gain/AGC

AGC mode

Gain

Auto

No default setting

Backlight comp

Shutter speed

Auto-iris

Off

Auto

Mode

Auto

Level

Peak

Default value depends on type of camera

White balance

Auto white balance

R-B white balance

M-G white balance

Sharpness

No default setting

Auto sharpness

Sharpness

No default setting

When the camera is reset, the following settings are not changed: park time, auto flip

disable, limit stops; and for the Spectra II™ only, zoom limit and proportional panning.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning off power to the Spectra II™ and Spectra Lite™ domes does not reset the camera.

Camera settings are retained in memory, and when the power is turned back on, the

settings will be the same as they were when it was turned off.

To reset the camera:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Reset Camera.

5. Press the Iris Open button to reset the camera.

GAIN/AGC

AGC Mode

There are three AGC (Automatic Gain Control) modes: auto, on, and off.

In the auto mode, the Spectra II™ and Spectra Lite™ domes automatically adjust the gain–

the amount of amplification the camera places on its video information in order to obtain a

full 1-volt peak-to-peak video signal out. If the iris is manually opened to its wide-open

position and the picture is weak, the AGC can be turned off and the gain increased

manually to improve the picture. For instructions on how to do this, refer to the Auto Iris

section. When you close the iris, the AGC will turn back on automatically when the lens iris

starts closing.

In the on mode the AGC is on all the time.

In the off mode the AGC is off.

To change the AGC mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Gain/AGC.

5. Press the Iris Open button to enter the Gain/AGC submenu.

6. Move the joystick up or down to position the cursor beside AGC mode.

7. Press the Iris Open button on your keyboard. A star will appear beside AGC mode and

the cursor will move to the right beside the word Auto, On, or Off.

8. Move the joystick up or down to position the cursor beside Auto, On, or Off.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Gain

The gain adjusts the signal level of the video output. Increasing the gain in low light

conditions will increase the level of noise in the picture.

To change the gain:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Gain/AGC.

5. Press the Iris Open button to enter the Gain/AGC submenu.

6. Move the joystick up or down to position the cursor beside Gain.

7. Press the Iris Open button on your keyboard. A star will appear beside Gain and the

cursor will move to the right beside the current gain setting (a numeric value).

8. Move the joystick up or down to change the gain. As you change the gain, the picture

on your monitor will get brighter or darker.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

AUTO IRIS

There are three settings for auto iris: mode, level, and peak.

To change the settings for auto iris:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Auto-Iris.

5. Press the Iris Open button on your keyboard. Another menu will appear with auto-iris

mode, level, and peak selections.

6. Move the joystick up or down to position the cursor beside one of the choices. Press

the Iris Open button on your keyboard.

MODE - The cursor moves to one of two choices: Auto or Off. In the Auto mode, the iris is

automatically adjusted to produce a constant video output as determined by the Level

setting below. In the Off mode, auto iris is disabled, and control is always manual. Move the

joystick up or down to toggle between Auto and Off. Press the Iris Open button to select the

choice, or press the Iris Close button if you do not want to change the setting.

LEVEL - The cursor moves to a numeric value, which the Spectra II™ dome uses to try to

maintain a certain light level. Changing the value of the Level setting will change the video

level to which the auto iris adjusts. This setting should be adjusted if the video level in the

auto iris mode is too bright or too dark. Move the joystick up or down to a value. Press the

Iris Open button to select the value, or press the Iris Close button if you do not want to

change the setting.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

PEAK - The cursor moves to a numeric value. Increasing this value will cause the auto iris

circuit to react more to highlights or “peaks” in the picture. Decreasing this value will cause

it to use the average video level to adjust the iris. Move the joystick up or down to a value.

Press the Iris Open button to select the value, or press the Iris Close button if you do not

want to change the setting.

If auto iris is in the auto mode, it remains that way until you manually open or close the iris.

The dome will return to auto iris when it is panned or tilted more than 15 degrees.

If there is not enough light for a good picture when the iris is wide open, you can increase

the gain of the camera to improve the picture. To do this:

1. The AGC mode (AGC Mode section) must be in either the Auto or Off mode. The

following steps will not work if the AGC mode is On.

2. Hold down the Iris Open button until the iris is wide open.

3. Release the button.

4. Within one second, hold down the button again. This will start increasing the camera

gain. Hold down the button until a desirable picture is obtained or the maximum gain is

reached.

SHUTTER SPEED

There are nine electronic shutter speed settings:

Auto

1/100

1/120

1/500

1/1000

1/2000

1/4000

1/10,000

1/30,000

In the Auto setting the camera controls the shutter speed automatically.

Increasing the shutter speed lowers the light sensitivity, but rapidly moving objects will be

less blurred as the speed is increased.

To change the electronic shutter speed settings:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera submenu.

6. Move the joystick up or down to position the cursor beside Shutter Speed.

7. Press the Iris Open button on your keyboard.

8. A star will appear beside Shutter Speed and the cursor will move to the right beside

the current shutter speed.

9. Move the joystick up or down to choose the shutter speed.

10. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO-FOCUS MODE

(This section applies to Spectra II™ only.)

There are two auto-focus modes: auto and off.

If auto focus is in the auto mode, pressing the Focus Far or Focus Near button will place

the focus in the manual mode. The dome will return to auto focus if you pan or tilt the unit

or do a zoom function.

If the mode is set to off, the dome will operate in the manual mode with one exception. If

you issue a command to go to a preset, auto focus will turn on and remain on until you

press the Focus Far or Focus Near button.

To change the mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera menu.

6. Move the joystick up or down to position the cursor beside Auto-Focus Mode.

7. Press the Iris Open button on your keyboard. A star will appear beside Auto-Focus

Mode and the cursor will move to the right beside the word Auto or Off.

8. Move the joystick up or down to toggle between Auto and Off.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

SHARPNESS

There are two modes for adjusting the sharpness of the picture: automatic and manual.

To change the mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera menu.

6. Move the joystick up or down to position the cursor beside Sharpness.

7. Press the Iris Open button. Another menu will appear with the auto sharpness and

sharpness selections.

8. Move the joystick up or down to position the cursor beside one of the choices. Press

the Iris Open button.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO SHARPNESS - The cursor moves to one of two choices: On or Off. Move the

joystick up or down to toggle between them. Press the Iris Open button to select the choice,

or press the Iris Close button if you do not want to change the setting.

SHARPNESS - The cursor moves to a numeric value. Move the joystick up or down to a

value. As you change the value, you will see the sharpness change. Press the Iris Open

button to select the value, or press the Iris Close button if you do not want to change the

setting. If the Auto Sharpness is on, it will change to off when you select a new value.

WHITE BALANCE (COLOR CAMERAS ONLY)

There are three settings for white balance: auto, red-blue, and magenta-green.

To change the white balance settings:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Camera, move the joystick up or down to position the

cursor beside Camera.

3. Press the Iris Open button to enter the Camera submenu.

4. Move the joystick up or down to position the cursor beside Next.

5. Press the Iris Open button to go to the next camera submenu.

6. Move the joystick up or down to position the cursor beside White Balance.

7. Press the Iris Open button on your keyboard. Another menu will appear with the auto,

red-blue, and magenta-green selections.

8. Move the joystick up or down to position the cursor beside one of the choices. Press

the Iris Open button on your keyboard.

AUTO WHITE BALANCE - The cursor moves to one of two choices: Auto or Off. Move

the joystick up or down to toggle between them. Press the Iris Open button to select the

choice, or press the Iris Close button if you do not want to change the setting.

R-B WHITE BALANCE - The cursor moves to a numeric value. Move the joystick up or

down to a value. As you change the value, you will see the color change on your monitor.

Press the Iris Open button to select the value, or press the Iris Close button if you do not

want to change the setting. If Auto White Balance is on, it will change to off when you select

a new value.

M-G WHITE BALANCE - The cursor moves to a numeric value. Move the joystick up or

down to a value. As you change the value, you will see the color change on your monitor.

Press the Iris Open button to select the value, or press the Iris Close button if you do not

want to change the setting. If Auto White Balance is on, it will change to off when you select

a new value.

LINE SYNCHRONIZATION

(This section applies to Spectra II™ only.)

You can turn the line synchronization on or off.

If it is on, you can adjust the synchronization of the power line voltage so that it is in phase

with other cameras. If cameras are out of phase with each other, they may produce what

appears to be vertical roll when switching between cameras.

If it is off, the dome synchronizes to an internal clock.

To change the line synchronization settings:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

2. If the cursor (>) is not beside Line Sync, move the joystick up or down to position the

cursor beside Line Sync.

3. Press the Iris Open button on your keyboard. Another menu will appear with the Line

Sync and Line Sync Phase selections.

4. Move the joystick up or down to position the cursor beside one of the choices.

LINE SYNC - The cursor moves to one of two choices: On or Off. Move the joystick up or

down to toggle between them.

Press the Iris Open button to select the choice. If you changed to Off, the camera may

reset itself as it adjusts to the new synchronization. If the camera resets, it will only affect

the line synchronization. It will not change any other camera parameters, such as auto

focus or auto iris.

Press the Iris Close button if you do not want to change the setting.

LINE SYNC PHASE - The cursor moves to a numeric value. Move the joystick up or

down to change the value.

Press the Iris Open button to select the choice. The value represents the phase angle in

tenths of a degree between 0 degrees and 359 degrees. For example, 900 is 90 degrees,

1200 is 120 degrees, and 2400 is 240 degrees. Press the Iris Open button on your

keyboard to select your choice. The Line Sync setting will change to On. The camera may

reset or the picture on your monitor may wiggle when you change the phase angle. If the

camera resets, it will only affect the line synchronization. It will not change any other

camera parameters, such as auto focus or auto iris.

Press the Iris Close button if you do not want to change the setting.

POWER-UP MODE

This feature lets the dome resume a desired condition following power-up. The menu

includes the following choices. (An asterisk denotes items that apply to the

Spectra II™ only.)

•

Default – On power-up, the dome goes through a configuration cycle and stops at

zero reference, showing “Configuration Done,” and address and mode settings on the

screen.

•

Park – The dome moves to preset 1 when the power-up sequence finishes. The only

text on the screen is the preset label (if any is programmed).

Scan Auto – The dome initiates scan mode when the power-up sequence finishes.

Again, there is no text.

Scan Frame – The dome initiates a frame scan when the power-up sequence

finishes.

Scan Rand – The dome initiates a random scan when the power-up sequence

finishes.

Full Pat* – The dome initiates its programmed pattern when the power-up sequence

finishes. The length can be set to 1.5, 3, or 6 minutes.

Half Pat 1* – The dome initiates the first half-pattern when the power-up sequence

finishes. The length can be set to .75, 1.5, or 3 minutes.

Half Pat 2* – The dome initiates the second half-pattern when the power-up

sequence finishes. The length can be set to .75, 1.5, or 3 minutes.

The default setting is Default.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

To select the power-up mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Power Up Mode, move the joystick up or down to

position the cursor beside Power Up Mode.

3. Press the Iris Open button to enter the Power Up Mode submenu.

4. Move the joystick up or down to cycle through the selections. Stop on the item you

want to select.

5. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

AUX MODE

(This section applies to Spectra II™ only.)

This feature defines the output relay as either Normal (under control of the head end),

Latching (pressing the AUX key turns on the AUX and the next press of the AUX key turns it

off), or Alarm (any alarm input activates the AUX).

To change the AUX mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside AUX, move the joystick up or down to position the cursor

beside AUX.

3. Press the Iris Open button to enter the AUX submenu.

4. Move the joystick up or down to position the cursor next to either Aux 1 mode or Aux 2

mode.

5. Press the Iris Open button. The cursor will move to the right beside the word Normal,

Latching, or Alarm.

6. Move the joystick up or down to toggle between Normal, Latching, or Alarm.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

ALARM RESUME

(This section applies to Spectra II™ only.)

This mode lets the dome resume its previous activity (scan, pattern, or previous position)

after all alarms are cleared.

To change the alarm resume mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or down to

position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Resume.

5. Press the Iris Open button. The cursor will move to the right beside the word On or Off.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

6. Move the joystick up or down to toggle between On or Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

ALARM DWELL

(This section applies to Spectra II™ only.)

This is the minimum time the Spectra II™ will stay at an alarm even if the alarm is present

for less than this amount of time.

To change the alarm dwell:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or down to

position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Dwell sec.

5. Press the Iris Open button. The cursor will move to the right beside the number of

seconds for the alarm dwell time.

6. Move the joystick up or down and hold to cycle through 1-200 seconds in one-second

increments.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

ALARM PRIORITY

(This section applies to Spectra II™ only.)

This feature lets you set alarm inputs as either high or low priority. A high priority alarm will

not release to a low priority alarm. Alarms will release or sequence between low priority

alarms only if no high priority alarm exists. (Refer to the Alarms section for more informa-

tion.)

To change alarm priority:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or down to

position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Priority.

5. Press the Iris Open button to enter the Alarm Priority submenu.

6. Move the joystick up or down to position the cursor beside the number of the alarm

input for which you want to set the priority.

7. Press the Iris Open button. The cursor will move to the right beside the word High or

Low.

8. Move the joystick up or down to toggle between the words High and Low.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

ALARM PATTERN

(This section applies to Spectra II™ only.)

NOTE: Pattern length is set

on the secondary menu en-

titled Other.

In response to an alarm, the Spectra II™ dome can do either one full pattern (1.5, 3, or 6

minutes long) or two half patterns (.75, 1.5, or 3 minutes long). You can choose one of the

following for each of the seven alarm inputs:

NOTE: To make the pattern

run to its end when an alarm

activates it, make alarm

dwell time longer than pat-

tern length. Therefore, if the

alarm goes away before the

end of the pattern, the pat-

tern will continue until the

dwell times out.

•

Full Pat (run full pattern)

Half Pat 1 (run half pattern 1)

Half Pat 2 (run half pattern 2)

No Pattern

To change the alarm pattern:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or down to

position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Alarm Pattern.

5. Press the Iris Open button to enter the Alarm Pattern submenu.

6. Move the joystick up or down to position the cursor beside the number of the alarm

input for which you want to set the pattern.

7. Press the Iris Open button. The cursor will move to the right beside the words Full Pat,

Half Pat 1, Half Pat 2, or No Pattern.

8. Move the joystick up or down to toggle between the choices.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

ZONE BLANK

(This section applies to Spectra II™ only.)

This feature lets you define any of eight zones as blanked for video when the camera pans

into the zone area. The choices are On and Off. On means video blanking is in effect. The

default is Off.

To change the blank zone setting:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Alarms, Zone Blank, move the joystick up or down to

position the cursor beside Alarms, Zone Blank.

3. Press the Iris Open button to enter the Alarms, Zone Blank submenu.

4. Move the joystick up or down to position the cursor beside Zone Blank.

5. Press the Iris Open button to enter the Zone Blank submenu.

6. Move the joystick up or down to position the cursor beside the number of the zone for

which you want to set the blank option.

7. Press the Iris Open button. The cursor will move to the right beside the word On or Off.

8. Move the joystick up or down to toggle between the words On and Off.

9. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

AUTO FLIP

There are two auto flip modes: on or off.

When the auto flip mode is on, the auto flip feature is enabled. When it is off, the feature is

disabled.

To change the auto flip mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Auto Flip.

5. Press the Iris Open button. A star will appear beside Auto Flip and the cursor will move

to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

PROPORTIONAL PAN

(This section applies to Spectra II™ only.)

There are two proportional pan modes: on or off.

When proportional pan mode is on, the proportional pan feature is enabled and the pan

(and tilt) speed will depend on the amount of zoom. At telephoto zoom settings, the pan

(and tilt) speeds will be slower for a given amount of joystick deflection than at wide zoom

settings. This keeps the image from moving too fast on the monitor when there is a large

amount of zoom. This slowing does not happen when going to a preset, but does occur in

turbo mode when high zoom is selected.

When the proportional pan mode is off, the feature is disabled and the pan speed will not

depend on the amount of zoom.

To change the proportional pan mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Proportional Pan.

5. Press the Iris Open button. A star will appear beside Proportional Pan and the cursor

will move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMIT STOPS

There are two types of limit stops:

Manual limit stops

Scan limit stops

When manual limit stops are set, a manual (joystick) pan operation will stop when a limit

stop is reached.

When scan limit stops are set, the dome will reverse direction during random, frame, or

auto scanning when a limit stop is reached.

Limit stops are controlled by software. To set limit stops:

1. Turn on the limit stop mode.

2. Program the limit stops.

Turning Limit Stops On or Off

To change the limit stop mode:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Limit Stops.

5. Press the Iris Open button. A star will appear beside Limit Stops and the cursor will

move to the right beside the word On or Off.

6. Move the joystick up or down to toggle between On and Off.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

Programming Limit Stops

MANUAL LIMIT STOPS

Refer to the documentation for your control system for programming presets, then do the

following:

NOTE: Programming

preset 90 (23) disables the

manual limit stops until

preset 91 (24) is set.

1. Make sure limit stops are turned ON (refer to the Limit Stops section), then exit the menu.

2. Push the joystick left until you reach the limit you want the camera to go to on the left.

3. Program preset 90 (23).

4. Push the joystick right to the limit you want the camera to go to on the right.

5. Program preset 91 (24).

Setting presets 90 (23) and 91 (24) to the same point disables manual limit stops.

SCAN LIMIT STOPS

Refer to the documentation for your control system for programming presets, then do the

following:

NOTE: On power-up, the

auto scan tilt angle will be

whatever angle the camera

was at when the right scan

limit was set.

1. Make sure limit stops are turned ON (refer to the Limit Stops section), then exit the menu.

2. Push the joystick left until you reach the limit you want the camera to go to on the left.

3. Program preset 92 (25).

4. Push the joystick right to the limit you want the camera to go to on the right.

5. Program preset 93 (26).

Setting presets 92 (25) and 93 (26) to the same point disables scan limit stops.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

PARK TIME MINUTES

This feature causes the dome to park at preset 1 after a programmed number of minutes of

control inactivity. The time can be set from 1 minute to 720 minutes (12 hours), or it can be

set to zero, which disables this feature.

NOTE: Preset 1 must be

programmed for the dome to

park.

To change the park time:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the Other submenu.

4. Move the joystick up or down to position the cursor beside Park Time Minutes.

5. Press the Iris Open button. A star will appear beside Park Time Minutes and the cursor

will move to the right beside the current park time.

6. Move the joystick up or down to change the park time.

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

SCAN SPEED

The scan speed is adjustable from 1-40 degrees per second. This occurs in three scan

modes: auto, random, and frame scan.

To change the scan speed:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

3. Press the Iris Open button to enter the submenu entitled Other.

4. Move the joystick up or down to position the cursor beside Scan Speed deg/s.

5. Press the Iris Open button. The cursor will move to the right beside the number of

degrees.

6. Move the joystick up or down to toggle through the number of degrees (1-40) until you

reach the number you want. (If set on a low number, the scan will appear to barely

move but is still functioning.)

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

PATTERN LENGTH

(This section applies to Spectra II™ only.)

CAUTION: If the

length is changed,

You can set the pattern length to 1.5, 3, or 6 minutes or have two half-patterns of .75, 1.5,

or 3 minutes long.

all patterns that

were stored are erased.

To set the pattern length:

1. Program preset 95 (28 if in 32-preset mode; refer to the Preset Functions section) to

access the main menu (refer to the Main Menu Access section). The main menu will

appear.

2. If the cursor (>) is not beside Other, move the joystick up or down to position the

cursor beside Other.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Press the Iris Open button to enter the submenu entitled Other.

4. Move the joystick up or down to position the cursor beside Pattern Length.

5. Press the Iris Open button. The cursor will move to the right beside the number of

minutes (1.5, 3, or 6).

6. Move the joystick up or down to toggle through the number of minutes (1.5, 3, or 6).

7. SELECT - Press the Iris Open button on your keyboard to select your choice.

CANCEL - Press the Iris Close button if you do not want to change the setting.

TROUBLESHOOTING

Symptom: Unit does not operate.

NOTE: The dome drive

contains no user-serviceable

parts. If there is a problem

with your dome drive, it

must be returned to Pelco

as a complete unit for

servicing.

1. Make sure your controller is trying to communicate with the unit and not another

camera.

2. Turn off power.

3. Remove the lower dome:

In-Ceiling Models - Insert the flat blade of a screwdriver into one of the slots on the

trim ring and twist the screwdriver to pop loose the trim ring and lower dome.

Pendant Models - Remove the two screws that hold the trim ring to the back box.

Insert the flat blade of a screwdriver into the slots on the trim ring and twist the

screwdriver to free the lower dome from the back box.

4. Remove the dome drive: Push in on the green drive eject tab on the side of the dome

drive and gently rock the dome drive to release the latch. When the green latch

releases, pull the dome down.

5. Turn on power.

6. If the red power LED on the door of the interconnect circuit board in the back box does

not light, turn off power.

a. Open the door to the interconnect circuit board and check the fuse. Refer to

Figure 12 or 13 for the location of the fuse. If the fuse is bad, replace it. To order

a replacement fuse from Pelco, specify the part number FUS1.6-5X20FAST. This

is a 1.6-ampere fuse, 5 x 20 mm, fast blow.

b. If the fuse is good, turn on power and use a voltmeter to check if 24 VAC is

getting to the power connector on the interconnect circuit board. Refer to Figure

12 or 13 for the location of the AC power connector.

c. If there is 24 VAC to the power connector, turn off power and return the back box

electronic assembly to the factory for repair. Refer to the Back Box Electronic

Assembly Removal section.

d. If there is no voltage at the power connector, check your power supply.

7. If the red power LED is lit, turn off power.

a. Open the door to the interconnect circuit board and check that all connectors are

fully seated.

b. Make sure the wiring is correct between the unit and controller.

c. Close the door. Check the switch settings on the dome drive (refer to Tables C,

D, and E) and reinstall the dome drive.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

d. Turn on power. If the unit still does not operate, turn off power and replace the dome

drive with a unit that is good, if you have a spare. Check the switch settings on the

substitute dome drive before installing it. If you do not have a spare, return the dome

drive to the factory. Also return the back box electronic assembly. Refer to the Back

Box Electronic Assembly Removal section.

e. If you substituted a dome drive, turn on power. If the unit operates, the original dome

drive is bad. Return it to the factory. If the unit still does not operate, then the

interconnect board is bad. Return the back box electronic assembly to the factory;

refer to the Back Box Electronic Assembly Removal section.

Symptom: Fan does not operate.

1. Turn off power.

2. Remove the lower dome:

In-Ceiling Models - Insert the flat blade of a screwdriver into one of the slots on the

trim ring and twist the screwdriver to pop loose the trim ring and lower dome.

Pendant Models - Remove the two screws that hold the trim ring to the back box.

Insert the flat blade of a screwdriver into the slots on the trim ring and twist the

screwdriver to free the lower dome from the back box.

3. Remove the dome drive: Push in on the green drive eject tab on the side of the dome

drive and gently rock the dome drive to release the latch. When the green latch

releases, pull the dome down.

4. Make sure the connector for the fan is fully seated.

5. Replace the dome drive. Turn on power. If the fan does not operate, return the back

box electronic assembly and dome drive to the factory for repair. Refer to the Back

Box Electronic Assembly Removal section.

Symptom: Alarms not cycling when more than one alarm is active

Reset all your alarm priorities to all LOW or all HIGH (refer to the Alarms section for an

explanation of alarm high/low priorities). To reset the alarm priorities, do the following:

1. Go to the Main Menu Access section and follow the instructions for accessing the

programming main menu.

2. Go to the Alarm Priority section and follow the instructions for setting the alarm priority.

Symptom: Alarms not going to preset

1. Check that the preset is defined.

2. Check that no higher priority alarm is activated.

3. Check that a pattern is not set for the affected alarm(s). If a pattern is set, the alarm

will run a pattern, not go to a preset. If a pattern (or patterns) is set, reset the

pattern(s) to NO PATTERN.

To reset a pattern, do the following:

1. Go to the Main Menu Access section and follow the instructions for accessing the

programming main menu.

2. Go to the Alarm Pattern section and follow the instructions for setting the alarm

pattern.

Symptom: Alarms not starting a pattern

Ensure that the pattern selected is valid. Any time you expect a pattern to execute, make

sure the pattern is recorded correctly and is valid.

Symptom: Motion problems

When troubleshooting motion problems on a system where alarms are connected, you can

eliminate alarms as a cause of the problem by disconnecting the alarm block in the back box.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

BACK BOX ELECTRONIC ASSEMBLY REMOVAL

To remove the back box electronic assembly:

1. Turn off power.

2. Open the interconnect door and disconnect all wiring to the back box.

3. Use an 11/32 socket driver to remove the three 8-32 washers and nuts that hold the

electronic assembly to the back box. When the screws are removed, the interconnect

back box receptacle will drop down. It may be necessary to move the open intercon-

nect door past 90 degrees vertical toward the side of the back box to release the door

from the built-in grounding strip (and free the interconnect back box receptacle).

4. Remove the interconnect back box receptacle with the electronic components from the

back box.

MAINTENANCE

DOME CLEANING

Clean the acrylic dome as necessary to maintain a clear picture. Be careful not to scratch

the surfaces of the dome.

Exterior Surface - Clean the dome's exterior surface with a nonabrasive cleaning cloth

and cleaning agent that is safe for acrylic. Either liquid or spray cleaner/wax suitable for fine

furniture is acceptable.

Interior Surface (Except Chrome or Gold) - Clean the same as the exterior surface.

Interior Surface (Chrome or Gold) - The inside surface of a chrome or gold dome is

easily scratched. Use the following precautions to maintain the dome's surface.

a. Always handle the dome from the outside of its circular flange.

b. Never touch the coated inside surface. The acid in your fingerprints will eventually

etch the coating if the fingerprints are not carefully removed according to the recom-

mended cleaning procedure in item “e”.

c. If dust or other contaminants accumulate on the dome's interior, remove the debris

with compressed air. Compressed air cans are available from photographic equipment

or electronic supply dealers.

d. If heavy residue accumulates and cannot be removed with air pressure, rinse with

water and immediately dry with air pressure so that water spots will not remain. Avoid

wiping the coated surface with direct hand pressure - it will easily abrade unless

extreme care is taken. Once scratched, the dome cannot be recoated.

e. If internal wiping is necessary, avoid hand rubbing. Instead, make a wick as follows:

Use a very soft paper towel. Roll a section into a tightly wound tube. Tear the tube in

half, and wet the fuzzy end of the wick with a solution of isopropyl alcohol diluted with

water. Hold the dome with its opening facing downward and wipe the interior of the

dome with the wet end of the wick. Use a circular motion, starting from the outside and

spiraling into the center. Use a new wick for each two passes over the dome.

SERVICE MANUAL

If you need to service your unit, obtain a service manual in one of the following ways:

•

Go to Pelco’s web site at ftp://www.pelco.com and find service manual C1455SM-B.

Call Pelco’s DataFAX service at 1-559-292-0435 and request document 214558.

Contact Pelco’s Literature Department and request service manual C1455SM-B.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

MECHANICAL

Construction

Back box:

Aluminum

Dome drive:

Lower dome:

Aluminum, ABS plastic

Acrylic

Cable Entry

In-Ceiling:

Pendant:

.75" (1.91 cm) conduit fitting

Through 1.5" (3.81 cm) NPT pendant mount

Pan Movement:

Vertical Tilt:

360° Continuous pan rotation

Unobstructed +2° to -92°

Manual Pan/Tilt

Speeds*

Pan:

0.5°-80°/sec manual operation, 150°/sec turbo

0.5°-40°/sec

Tilt:

Preset Speeds

Pan:

Tilt

250°/sec

200°/sec

* For variable-speed operation an appropriate controller is required. With fixed-speed

controllers, Spectra II™ and Spectra Lite™ pan speed is 30°/sec and tilt speed is 12°/

sec. The CM6700 controller with the KBD200 keyboard has programmable fixed speeds.

ELECTRICAL

Input Voltage:

18-30 VAC, 24 VAC nominal

30 vA

Input Power

In-ceiling:

Indoor pendant: 30 vA

Outdoor pendant: 75 vA

Fuse:

1.6 A

Relay Contacts

Type:

AUX 1

Form C

AUX 2 Output

Open collector transistor output

Voltage:

Low voltage (<40 V) 32 VDC maximum

Current:

2 A maximum

150 mA maximum

GENERAL

Environment

In-Ceiling:

Pendant:

Indoor only

Indoor/outdoor

Operating Range

In-Ceiling:

32° to 140°F (0° to 60°C) intermittent operation; 32° to 122°F (0° to

50°C) continuous operation

Pendant

Without Heater: 32° to 140°F (0° to 60°C) absolute maximum operating temperature;

32° to 122°F (0° to 50°C) sustained maximum operating temperature

With Heater*:

(Assumes no wind chill factor; for detailed test conditions, contact Pelco.)

Maximum operating temperature: 140°F (60°C) absolute maximum;

122°F (50°C) sustained maximum

Minimum operating temperature: -60°F (-51.11°C) absolute minimum;

minimal icing at -50°F (-45.56°C) sustained minimum; prevents icing at

-40°F (-40°C) sustained minimum; de-ices .1 inch (2.5 mm) within 3

hours after power-up

Dimensions:

See Figure 18

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

TOP PORTION OF BACK BOX

DOME IS SECURED

IS REMOVABLE FOR SURFACE TO CEILING BY

MOUNT APPLICATIONS

MOUNTING BRACKET

8.52

(21.64)

7.25 (18.13)

6.60 (16.76)

5.25

(13.34)

6.75

(17.15)

10.90

(27.69)

5.83

(14.80)

3.25

(8.26)

5.90 (14.99)

8.25 (20.96)

5.90

(14.99)

IN-CEILING DOME

PENDANT DOME

NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.

Figure 18. SD5 Series Dimension Drawing

Ratings:

Weight

NEMA Type 1–In-ceiling back boxes, all dome drives

NEMA Type 4–Pendant back boxes

IP 66–Pendant back boxes

Unit

Shipping

In-Ceiling

Back Box:

Dome Drive:

Lower Dome: .19 lb (.09 kg)

Pendant

2.6 lb (1.18 kg)

2.65 lb (1.20 kg)

4 lb (1.81 kg)

5 lb (2.27 kg)

1 lb (.45 kg)

Back Box:

2.85 lb (1.28 kg)

5 lb (2.27 kg)

Add 1.25 lbs (.57 kg) for heater and sun shield

Dome Drive:

2.65 lb (1.20 kg)

5 lb (2.27 kg)

Lower Dome: 1.30 lb (.59 kg)

2.20 lb (1.0 kg)

Add .25 lbs (.11 kg) for heater

* Assumes no wind chill factor; for detailed test conditions, contact Pelco.

CAMERAS

COLOR (Spectra II™ and Spectra Lite™)

Signal Format:

NTSC (Spectra II™ model DD5AC)

PAL (Spectra II™ model DD5AC-X)

NTSC (Spectra Lite™ model DD5T-C)

PAL (Spectra Lite™ model DD5T-C-X)

Scanning System:

Image Sensor:

2:1 interlace

1/4-inch interline transfer CCD

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

Effective Pixels

(NTSC Spectra II™):

(PAL Spectra II™):

768 (H) x 494 (V)

752 (H) x 582 (V)

(NTSC Spectra Lite™): 510 (H) x 492 (V)

(PAL Spectra Lite™):

500 (H) x 582 (V)

Horizontal Resolution

(Spectra II™):

(Spectra Lite™):

>450 TV lines

>330 TV lines

Lens

Minimum f-stop

(Spectra II™):

F1.4

(NTSC Spectra Lite™): F1.6-2.8

(PAL Spectra Lite™):

F1.6-2.5

Focal Length

(Spectra II™):

(Spectra Lite™):

4 mm to 64 mm optical

4 mm to 48 mm optical

Zoom Ratio

(Spectra II™):

(Spectra Lite™):

16X optical zoom, 8X electronic zoom

12X optical zoom

Horizontal Angle of View

(Spectra II™):

(Spectra Lite™):

47° (at 4 mm wide zoom), 3° (at 64 mm telephoto zoom)

47° (at 4 mm wide zoom), 4° (at 48 mm telephoto zoom)

MTBF:

>2 million cycles at room temperature (zoom, focus, iris)

Focus

(Spectra II™):

(Spectra Lite™):

Automatic and manual override

Manual with capability to focus when going to a preset position

Sensitivity

(Spectra II™ NTSC):

(Spectra II™ PAL):

1.5 lux at f1.4 at signal level of 40 IRE (NTSC), gain 22.0 dB

1.5 lux at f1.4 at 300 mV, gain 24.7 dB

(Spectra Lite™ NTSC): 4 lux at f1.6 at signal level of 40 IRE (NTSC), gain high

(Spectra Lite™ PAL):

Signal Process:

3 lux at f1.6 at 300 mV

DSP-3R

Sync System

(Spectra II™):

(Spectra Lite™):

AC line lock, phase adjustable via remote control*

Internal

White Balance:

Automatic with manual override*

Shutter Speed

(Spectra II™ NTSC):

(Spectra II™ PAL):

Automatic (electronic iris)/manual

1/60-1/30,000*

1/50-1/30,000*

(Spectra Lite™ NTSC): 1/100-1/30,000*

(Spectra Lite™ PAL):

1/100-1/30,000*

Iris Control:

(Spectra II™):

(Spectra Lite™):

Automatic with manual override*

Gain Control:

Automatic with manual override*

Video Output

(NTSC):

(PAL):

.714V ± .07V (100 IRE ± 10 IRE)

.7V ± .07V

Signal to Noise Ratio:

>46 dB

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

MONOCHROME (Spectra II™ Only)

Signal Format

EIA (model DD5AM)

CCIR (model DD5AM-X)

Scanning System:

Image Sensor

2:1 interlace

1/4-inch interline transfer CCD

>500 TV lines

Horizontal Resolution:

Effective Pixels

EIA:

CCIR:

768 (H) x 494 (V)

752 (H) x 582 (V)

Lens:

Minimum f-stop:

Focal Length:

Zoom Ratio:

Horizontal

Angle of View

MTBF:

F1.4

4 mm to 64 mm optical

16X optical zoom, 8X electronic zoom

47° (at 4 mm wide zoom), 3° (at 64 mm telephoto zoom)

>2 million cycles at room temperature (zoom, focus, iris)

Automatic with manual override

Focus:

Sensitivity

EIA:

.1 lux at f1.4, AGC gain 26.5 dB, signal level 40 IRE, without IR

cut filter

CCIR:

.1 lux at f1.4, AGC gain 29.5 dB, signal level 300 mV, without

IR cut filter

Signal Process:

Sync System:

DSP-3R

AC line lock, phase adjustable via remote control*

Shutter Speed:

EIA:

Automatic (electronic iris)/manual

1/60-1/30,000

CCIR:

1/50-1/30,000

Iris Control:

Automatic with manual override*

Gain Control:

Video Output

EIA:

CCIR:

.714V ± .07V (100 IRE ± 10 IRE)

.7V ± .07V

Signal to Noise Ratio:

>46 dB

* Manual control of camera setup functions can be done with CM6700, CM8500, CM9500,

CM9760 and MPT9500 controllers, but not with CM7500, MPT9000 or KBD9000

controllers.

(Design and product specifications subject to change without notice.)

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

REGULATORY NOTICES

Note: This equipment has been tested and found to comply with the limits of a Class A

digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

WARRANTY AND RETURN INFORMATION

WARRANTY

If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100

Pelco will repair or replace, without charge, any merchandise proved defective

in material or workmanship for a period of one year after the date of shipment.

Exceptions to this warranty are as noted below:

or (559) 292-1981 to obtain a Repair Authorization number (RA), and provide

the following information:

1. Model and serial number

2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number

3. Details of the defect or problem

•

Three years on Genex™ Series (multiplexers, server, and keyboard).

Two years on all standard motorized and fixed focal length lenses.

Two years on Esprit™, Legacy^®, Intercept^®, PV1000 Series, CM6700/

CM8500/CM9500/CM9750/CM9760 Matrix, Spectra^®, DF5 Series and DF8

Fixed Dome products.

Two years on WW5700 series window wiper (excluding wiper blades).

Two years on cameras.

Six months on all pan and tilts, scanners or preset lenses used in continu-

If there is a dispute regarding the warranty of a product which does not fall

under the warranty conditions stated above, please include a written explana-

tion with the product when returned.

•

Ship freight prepaid to:

Pelco

ous motion applications (that is, preset scan, tour and auto scan modes).

300 West Pontiac Way

Clovis, CA 93612-5699

Pelco will warrant all replacement parts and repairs for 90 days from the date of

Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid

to Pelco, Clovis, California. Repairs made necessary by reason of misuse, al-

teration, normal wear, or accident are not covered under this warranty.

Method of return shipment shall be the same or equal to the method by which

the item was received by Pelco.

RETURNS

Pelco assumes no risk and shall be subject to no liability for damages or loss

resulting from the specific use or application made of the Products. Pelco’s

liability for any claim, whether based on breach of contract, negligence, infringe-

ment of any rights of any party or product liability, relating to the Products shall

not exceed the price paid by the Dealer to Pelco for such Products. In no event

will Pelco be liable for any special, incidental or consequential damages (includ-

ing loss of use, loss of profit and claims of third parties) however caused, whether

by the negligence of Pelco or otherwise.

In order to expedite parts returned to the factory for repair or credit, please call

the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization num-

ber (CA number if returned for credit, and RA number if returned for repair).

Goods returned for repair or credit should be clearly identified with the assigned

CA/RA number and freight should be prepaid.All merchandise returned for credit

may be subject to a 20% restocking and refurbishing charge.

Ship freight prepaid to:

Pelco

The above warranty provides the Dealer with specific legal rights. The Dealer

may also have additional rights, which are subject to variation from state to state.

300 West Pontiac Way

Clovis, CA 93612-5699

REVISION HISTORY

Manual #

Date

Comments

C1487M

7/98

Original version.

C1487M-A

11/98

Revised the manual to incorporate Spectra Lite™ material. Added material on CCIR and EIA monochrome cameras, and PAL

color camera. Revised material in Section 5.11.21.2, Programming Limit Stops. Revised Section 6.0, Troubleshooting. Changed

the fixed-speed controller rate in Section 8.0, Specifications.

C1487M-B

C1487M-C

2/99

Changed Spectra Lite™ model numbers, and added comments that the line sync feature is not functional for the DD5T-C

model of Spectra Lite™. Changed power specifications for indoor models from 25 vA to 30 vA and for outdoor models from 90

vA to 75 vA. Revised maximum temperature operating ranges. Revised color camera specifications.

Changed auto iris material to include Spectra Lite™ as well as Spectra II™.

Added a note relating to running patterns when an alarm activates. Changed the preset tilt speed from 100 to 200 degrees/

second. Added model number and specifications for Spectra Lite™ PAL camera. Revised manual to new format.

3/99

7/99

® Pelco and the Pelco logo are registered trademarks of Pelco.

Pelco Manual C1487M-C (7/99)

Download from Www.Somanuals.com. All Manuals Search And Download.

PDP Video Gaming Accessories BB 7559 User Manual
Philips Cordless Telephone CD4453Q User Manual
Philips MP3 Player 64MB User Manual
Philips Telephone CD490 User Manual
Phoenix Gold Speaker TI65CS User Manual
Pioneer Blu ray Player BDP 41FD User Manual
Pioneer Car Speaker S HTD340 User Manual
Polycom IP Phone 1725 12490 001 User Manual
Poulan Lawn Mower Accessory 183187 User Manual
Proctor Silex Microwave Oven E7017NP BN User Manual