Pelco Home Security System SB19 1 SB1901 User Manual

®
SB19/SB1900 Series  
Discreet Surveillance Enclosures  
Installation/Operation Manual  
C467M-D (5/95)  
(800) 289-9100 or (1-559) 292-1981 • FAX (800) 289-9150 or (1-559) 292-3827  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION AND OPERATION MANUAL  
DISCREET SURVEILLANCE ENCLOSURES:  
MODEL SB19/SB1900 SERIES  
CAUTION  
This device is designed to operate at 24VAC power.  
MODEL SB19-1/SB1901 SERIES  
MODEL DD1900 SERIES  
Input voltage must not exceed 28 volts or drop be-  
low 22 volts or else damage to the motors will occur.  
Should you need assistance with this or any Pelco  
product, please call 1-800-298-9100or 1-559-  
292-1981.  
1.0 WARNINGS  
Priortoinstallationanduseofthisproduct,thefollowing  
WARNINGS should be observed.  
3. OnlyusereplacementpartsrecommendedbyPelco.  
4. After replacement/repair of this unit’s electrical  
components, conduct a resistance measurement  
betweenlineandexposedpartstoverifytheexposed  
parts have not been connected to line circuitry.  
1. Installation and servicing should only be done by  
Qualified Service Personnel and conform to all  
Local codes.  
2. Unless the unit is specifically marked as a NEMA  
Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is  
designed for indoor use only and it must not be  
installed where exposed to rain and moisture.  
5. The installation method and materials should be  
capable of supporting four (4) times the weight of  
theenclosure,pan/tilt,cameraandlenscombination.  
The product may bear the following  
marks:  
This symbol indicates that dangerous voltage  
constituting a risk of electric shock is present  
within this unit.  
This symbol indicates that there are important  
operating and maintenance instructions in the  
literature accompanying this unit.  
CAUTION:  
RISK OF ELECTRIC SHOCK.  
DO NOT OPEN.  
CAUTION:  
TOREDUCETHERISKOFELECTRICAL  
SHOCK, DO NOT REMOVE COVER. NO  
USER-SERVICEABLE PARTS INSIDE.  
REFER SERVICING TO QUALIFIED  
SERVICE PERSONNEL.  
Please thoroughly familiarize yourself with the information in this manual  
prior to installation and operation.  
Pelco Manual C467M-D (5/95)  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
2.0 SCOPE  
NOTE: The following are the cable require-  
ments. A relay box (RB24) is available to  
extend the operating distance. Consult the  
factory for details.  
The information contained within this manual covers  
the SB19/SB1900 Series of Discreet Surveillance En-  
closures.  
3.0 DESCRIPTION  
Non-PP Models  
The SB19 is a low profile, hemisphere, discreet sur-  
veillance dome for CCD type cameras designed for ease  
of installation, relocation, and servicing in hard ceiling  
applications or in a standard 2' x 2' or 2' x 4' suspended  
ceiling grid.  
12 Conductors  
13 Conductors*  
20 Awg  
18 Awg  
16 Awg  
190 ft (57.91 m)  
300 ft (91.44 m)  
480 ft (146.3 m)  
380 ft (115.82 m)  
600 ft (182.88 m)  
960 ft (292.61 m)  
The black opaque lower dome effectively conceals the  
camera while providing an inconspicuous viewing win-  
dow. The dome mounts directly to the pan/tilt (or fixed  
camera mount), thus keeping the viewing window and  
camera aligned.  
Models with PP  
18 Conductors  
19 Conductors*  
20 Awg  
18 Awg  
16 Awg  
190 ft (57.91 m)  
300 ft (91.44 m)  
480 ft (146.3 m)  
380 ft (115.82 m)  
600 ft (182.88 m)  
960 ft (292.61 m)  
To simplify installation even further, Pelco offers  
system packages with factory installed standard com-  
ponents from its regular product line. Options include  
a 24 VAC pan/tilt with factory pre-wired feed-through  
for all control functions (i.e., pan/tilt, motorized zoom  
lens, camera power (24 VAC) and video), continuous  
360° pan rotation, and a position feedback package for  
presets.  
*Using 2 conductor common.  
Calculations are based on a 10% cable loss with both  
motors running.  
4.2 WIRING INSTRUCTIONS  
The dome and camera assembly rotate at a speed of 24  
degrees/second for complete 360 degree surveillance  
coverage.  
The SB1900 and SB1900-SL include a pan/tilt which  
is pre-wired for all control functions (pan/tilt, motor-  
ized zoom lens, camera power (24 VAC), and video).  
All connections are made to the input terminal block in  
the J-box on top of the back box, eliminating the need  
for wiring harnesses made in the field. Wire the control  
cable according to the wiring diagram in Figure 1.  
The back box is constructed of aluminum to meet most  
fire code requirements for installation in open plenum  
ceilings.  
4.0 INSTALLATION  
Save the shipping carton and plastic packaging in case  
the unit must be returned for credit or repair.  
4.1 CONDUCTOR AND CABLE  
REQUIREMENTS  
(All Models Except SB19)  
A minimum of 12 conductors plus coax is required,  
which includes common requirements for motorized  
zoom lens and camera AC power. (An additional coax  
is required for camera sync.)  
2
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Figure 1. SB1900 Series Wiring Diagram  
Pelco Manual C467M-D (5/95)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.3 MOUNTING INSTRUCTIONS  
2. Remove the factory assembled 12.5" round face-  
plate from the back box by disengaging the ser-  
rated studs.  
Determine the type of mounting desired. The enclo-  
sure can be mounted in a hard ceiling, completely re-  
place a standard 2' x 2' suspended ceiling tile using the  
APSB19 optional faceplate, or be inserted through a  
cut-out in a standard 2' x 2' suspended ceiling tile.  
3. Remove the factory assembled 14.5" square mount-  
ing plate by removing the four (4) 1/4-20 bolts.  
4. Place the 14.5" square mounting plate on the re-  
moved ceiling tile, centering all four edges of the  
plate to the tile. Draw an outline of the octagon  
opening in the sub-plate onto the tile.  
Handle the lower dome with care so as not to scratch or  
get fingerprints on the viewing window.  
4.3.1 Suspended Ceiling Mounting  
5. Using a sharp knife or keysaw, cut out the octagon  
outlined on the tile.  
4.3.1.1 Suspended Ceiling -  
Preferred Method  
6. Replace the ceiling tile and place the mounting  
plate on top of it, centering the plate on the tile.  
Attach the back box mount rails with 1/4-20 nuts  
(provided) to two opposite sides of the mounting  
plate. Use these mount rails to secure the back box  
in place so that it can’t move when inserting or  
removing the dome drive unit, and so that all of  
the weight of the unit is not on the ceiling tile, per  
local code. (Refer to Figure 2.)  
1. Determine the location for mounting the enclosure  
and remove the appropriate ceiling tile.  
IMPORTANT: When installing the enclo-  
sure in a 2' x 4' ceiling grid, cut the ceiling tile  
in half and install an additional “T” rail for  
support.  
Figure 2. Back Box Mounting Rail Installation  
4
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. Slide the back box through the ceiling tile and  
mounting plate and replace the four (4) 1/4-20 bolts  
and tighten to secure the back box to the mounting  
plate.  
NOTE: For PC1804B and PC900U cameras,  
remove the mounting bracket with the two 1/4-  
20 holes in it from the camera’s power supply,  
align the camera power supply so that the two  
(2) threaded holes in the power supply align  
over two of the round holes in the camera power  
supply bracket on the pan/tilt, and attach it with  
the screws provided with the camera.  
8. Check the alignment of the back box to the ceiling  
tile by attaching the 12.5" round faceplate trim to  
the bottom of the back box, aligning the two studs  
with two of the holes in the flanges of the back  
box and engaging the studs. The studs should en-  
gage, while leaving a very minimal gap between  
the ceiling and faceplate trim. Loosen the 1/4-20  
hardware in the sides of the back box and make  
adjustments as required. Insure that the face of the  
back box is level with the ceiling.  
11. Hook up camera power, video, and lens with the  
connectors supplied, if not factory pre-assembled.  
Coil the excess camera cable and tie it down with  
tie-wraps to the pan/tilt body.  
NOTE: To insert or remove the drive unit from  
the back box, the drive unit may need to be ro-  
tated 90° so that the wiring cover and/or cam-  
era power supply does not interfere with the  
side of the back box. If difficulty inserting or  
removing the drive unit is experienced, slowly  
and gently rotate the drive unit 90°.  
9. Attach the lens and camera head to the tilt table  
(hardware not supplied), if not factory pre-assembled,  
using the camera/lens position template supplied  
as a guide (see Figure 3). Locate the lens and cam-  
era so that when the notched area in the template  
is fitted under the tilt table, the lens and camera do  
not project further out from the tilt table than al-  
lowed by the template. Also, the lens must not  
project higher than the long end of the template.  
12. Engage the connector of the coil cord into the con-  
nector of the pan/tilt and attach the safety clamp;  
then insert the pan/tilt into the back box, feeding  
the coil cord back through the opening in the top  
of the back box. Position the pan/tilt in the back  
box so that the horizontal studs in the pan/tilt mount  
bracket align with the slots in the back box mount  
bracket. Lift the pan/tilt until it reaches its stop,  
then slide it to one side while letting it drop about  
1/4 inch (see Figure 4).  
NOTE: If the camera and lens do not fit within  
the boundaries of the template, they will not fit  
inside the dome and need to be replaced with  
smaller units.  
10. Mount the camera power supply onto the bracket  
provided, if not factory pre-assembled. (Screws to  
mount the camera power supply and lens are not  
provided with the pan/tilt.)  
LENS  
SUPPLIED  
TEMPLATE  
CAMERA  
3.25  
(8.26)  
MAX  
TILT TABLE  
.875  
(2.22)  
MAX  
1.625  
(4.13)  
MAX  
6.5  
(16.51)  
MAX  
GENERAL LENS MAXIMUM EXTENSIONS  
PAST EDGES OF TILT TABLE  
NOTE: VALUES IN PARENTHESE ARE CENTIMETERS;  
ALL OTHERS ARE IN INCHES  
Figure 3. Camera/Lens Mounting Dimensions  
Pelco Manual C467M-D (5/95)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
13. Attach the dome to the pan/tilt by aligning the two  
ball studs protruding through the flange of the dome  
with the two holes in the dome attachment brack-  
ets and engaging the studs.  
15. Attach the faceplate trim to the back box by align-  
ing the two serrated studs with two of the holes in  
the edges of the back box and engaging the studs.  
16. Operate the pan/tilt to verify that there are no ob-  
structions or dragging cables within the back box  
or dome.  
14. Attach the safety chain on the side of the back box  
to the short 4-40 threaded screw in the 12.5" round  
faceplate trim with the provided hardware.  
UPPER MOUNTING PLATE  
INSIDE BACK COVER  
SAFETY SPRING CLIP  
ATTACHED TO COIL CORD  
(CAN BE POSITIONED  
180° FROM SHOWN)  
LOWER MOUNTING PLATE  
ATTACHED TO PAN AND TILT  
Figure 4. Pan/Tilt Mounting Detail  
6
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4.3.1.2 Suspended Ceiling Tile  
Replacement Mounting  
template.Also, the lens must not project higher than  
the long end of the template.  
NOTE: If the camera and lens do not fit within  
the boundaries of the template, they will not fit  
inside the dome and need to be replaced with  
smaller units.  
To mount the enclosure into a suspended ceiling grid  
where the tile is replaced, perform the following steps.  
1. Determine the location for mounting the enclosure  
and remove the appropriate ceiling tile.  
8. Mount the camera power supply onto the bracket  
provided, if not factory pre-assembled. (Screws to  
mount the camera power supply and lens are not  
provided with the pan/tilt.)  
IMPORTANT: When installing the enclo-  
sure in a 2' x 4' ceiling grid, cut the ceiling tile  
in half and install an additional “T” rail for  
support.  
NOTE: For PC1804B and PC900U cameras,  
remove the mounting bracket with the two 1/4-  
20 threaded holes in it from the camera’s power  
supply, align the camera power supply so that  
the two (2) threaded holes in the power sup-  
ply align over two of the round holes in the  
camera power supply bracket on the pan/tilt,  
and attach it with the screws provided with  
the camera.  
2. Angle the 23.75" back box mounting plate (part  
number APSB19, which must be ordered sepa-  
rately) through the grid opening and set the plate  
into the grid. Attach the back box mount rails with  
1/4-20 nuts (provided) to two opposite sides of the  
mounting plate (see Figure 2). Use these mount  
rails to secure the back box in place so that it can’t  
move when inserting or removing the dome drive  
unit, and so that all of the weight of the unit is not  
on the ceiling tile, per local code.  
9. Hook up camera power, video, and lens with the  
connectors supplied, if not factory pre-assembled.  
Coil the excess camera cable and tie it down with  
tie-wraps to the pan/tilt body.  
3. Remove the factory assembled 12.5" round face-  
plate from the back box by disengaging the ser-  
rated studs.  
NOTE: To insert or remove the drive unit from  
the back box, the drive unit may need to be ro-  
tated 90° so that the wiring cover and/or cam-  
era power supply does not interfere with the  
side of the back box. If difficulty inserting or  
removing the drive unit is experienced, slowly  
and gently rotate the drive unit 90°.  
4. Remove the factory assembled 14.5" square mount-  
ing plate by removing the four (4) 1-4/20 bolts.  
5. Slide the back box through the mounting plate and  
replace the four (4) 1/4-20 bolts and tighten to se-  
cure the back box to the mounting plate.  
10. Engage the connector of the coil cord into the con-  
nector of the pan/tilt and attach the safety clamp;  
then insert the pan/tilt into the back box, feeding  
the coil cord back through the opening in the top  
of the back box. Position the pan/tilt in the back  
box so that the horizontal studs in the pan/tilt mount  
bracket align with slots in the back box mount  
bracket. Lift the pan/tilt until it reaches its stop,  
then slide it to one side while letting it drop about  
1/4 inch (see Figure 4).  
6. Check the alignment of the back box to the mount-  
ing plate by attaching the 12.5" round faceplate  
trim to the bottom of the back box, aligning the  
two studs with two of the holes in the flanges of  
the back box and engaging the studs. The studs  
should engage, while leaving a very minimal gap  
between the ceiling and faceplate trim. Loosen the  
1/4-20 hardware in the sides of the back box and  
make adjustments as required. Insure that the face  
of the back box is level with the ceiling.  
11. Attach the dome to the pan/tilt by aligning the two  
ball studs protruding through the flange of the dome  
with the two holes in the dome attachment brack-  
ets and engaging the studs.  
7. Attach the lens and camera head to the tilt table (hard-  
ware not supplied), if not factory pre-assembled, us-  
ing the camera/lens position template supplied as a  
guide (see Figure 3). Locate the lens and camera so  
that when the notched area in the template is fitted  
under the tilt table, the lens and camera do not project  
further out from the tilt table than allowed by the  
Pelco Manual C467M-D (5/95)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. Attach the safety chain on the side of the back box  
to the short 4-40 threaded screw in the 12.5" round  
faceplate trim with the provided hardware.  
6. Attach the lens and camera head to the tilt table  
(hardware not supplied), if not factory pre-assembled,  
using the camera/lens position template supplied  
as a guide (see Figure 3). Locate the lens and cam-  
era so that when the notched area in the template  
is fitted under the tilt table, the lens and camera do  
not project further out from the tilt table than al-  
lowed by the template. Also, the lens must not  
project higher than the long end of the template.  
13. Attach the faceplate trim to the back box by align-  
ing the two serrated studs with two of the holes in  
the edges of the back box and engaging the studs.  
14. Operate the pan/tilt to verify that there are no ob-  
structions or dragging cables within the back box  
or dome.  
NOTE: If the camera and lens do not fit within  
the boundaries of the template, they will not fit  
inside the dome and need to be replaced with  
smaller units.  
4.3.2 Hard Ceiling Mounting  
To mount the enclosure into a hard ceiling, perform the  
following steps.  
7. Mount the camera power supply onto the bracket  
provided, if not factory pre-assembled. (Screws to  
mount the camera power supply and lens are not  
provided with the pan/tilt.)  
1. Determine the location and direction of the enclo-  
sure. Ideally, the enclosure cutout should be paral-  
lel and adjacent, or perpendicular, to any ceiling  
structure. Cut an opening (refer to Figure 8 for di-  
mensions).  
8. Hook up camera power, video, and lens with the  
connectors supplied, if not factory pre-assembled.  
Coil the excess camera cable and tie it down with  
tie-wraps to the pan/tilt body.  
2. Remove the factory assembled 12.5" round face-  
plate from the back box by disengaging the ser-  
rated studs.  
NOTE: To insert or remove the drive unit from  
the back box, the drive unit may need to be ro-  
tated 90° so that the wiring cover and/or cam-  
era power supply does not interfere with the  
side of the back box. If difficulty inserting or  
removing the drive unit is experienced, slowly  
and gently rotate the drive unit 90°.  
3. Remove the factory assembled 14.5" square mount-  
ing plate by removing the four (4) 1/4-20 bolts and  
place it over the opening. Attach the back box  
mount rails to the mounting plate with 1/4-20 nuts  
(provided) to two opposite sides of the mounting  
plate (see Figure 2). Use these mount rails to se-  
cure the back box in place so that it can’t move  
when inserting or removing the dome drive unit,  
and so that all of the weight of the unit is not on  
the ceiling tile, per local code.  
9. Engage the connector of the coil cord into the con-  
nector of the pan/tilt and attach the safety clamp;  
then insert the pan/tilt into the back box, feeding  
the coil cord back through the opening in the top  
of the back box. Position the pan/tilt in the back  
box so that the horizontal studs in the pan/tilt mount  
bracket align with slots in the back box mounting  
bracket. Lift the pan/tilt until it reaches its stop,  
then slide it to one side while letting it drop about  
1/4 inch (see Figure 4).  
4. Slide the back box through the mounting plate and  
replace the four (4) 1/4-20 bolts and tighten to se-  
cure the back box to the mounting plate.  
5. Check the alignment of the back box to the ceiling  
by attaching the 12.5" round faceplate trim to the  
bottom of the back box, aligning the two studs with  
two of the holes in the flanges of the back box and  
engaging the studs. The studs should engage, while  
leaving a very minimal gap between the ceiling  
and faceplate trim. Loosen the 1/4-20 hardware in  
the sides of the back box and make adjustments  
are required. Insure that the face of the back box is  
level with the ceiling.  
10. Attach the dome to the pan/tilt by aligning the two  
ball studs protruding through the flange of the dome  
with the two holes in the dome attachment brack-  
ets and engaging the studs.  
11. Attach the safety chain on the side of the back box  
to the short 4-40 threaded screw in the 12.5" round  
faceplate trim with the provided hardware.  
8
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12. Attach the faceplate trim to the back box by align-  
ing the two serrated studs with two of the holes in  
the edges of the back box and engaging the studs.  
2. Pan to the desired left position, remove the drive  
unit from the back box and adjust the pan limit  
stop until the actuator clicks, and lock into posi-  
tion. Replace the drive unit.  
13. Operate the pan/tilt to verify that there are no ob-  
structions or dragging cables within the back box  
or dome.  
3. Pan to the right and left to verify the exact posi-  
tioning.  
4.4 CONNECTOR ASSEMBLY  
4. The tilt limit is factory set at 0 to -90° travel (hori-  
zontal to vertical). The tilt can be adjusted to any  
point between horizontal and vertical; however,  
under normal conditions the tilt limits should not  
require adjustment.  
To install and test the SB1900 Series enclosures you  
may need to fabricate the interconnecting cable as out-  
lined below. (Pretested wire harnesses, WH1900-06 and  
WH1900-25, are optional cables for the SB1900 Se-  
ries dome enclosures).  
5. To alter the factory set tilt limit*, bend the actua-  
tor stops on the microswitches (see Figure 6).  
Move the tilt table to the desired position and ad-  
just the actuators until the switch clicks; lock into  
position.  
1. Strip back the cable jacket approximately 2 inches  
and separate the individual conductors.  
2. Attach spade lugs to each wire and mate BNC to  
coax and camera sync.  
6. Tilt up and down to verify exact positioning.  
3. Pop out a knock-out in one of the ends of the J-box  
(on top of back box). Thread cable into J-box  
through knock-out and attach each wire to the ter-  
minal block, as marked beside terminal block, and  
engage BNC connectors or video and camer sync.  
* It should be emphasized that only very minor adjust-  
ments should be made by bending the actuator attached  
to the microswitch; and then, only for the reason of  
bringing it within factory specifications.  
4.5 ADJUSTMENTS  
To adjust the pan/tilt limits, perform the following steps.  
Refer to Figure 5 for limit stop locations.  
LIMIT STOP LEFT  
LIMIT STOP RIGHT  
LIMIT STOP FIXED  
LIMIT ACTUATOR  
CAUTION: Do not attempt to adjust limit  
stops when the pan/tilt is in operation. Damage  
to the equipment can result. Also, do not oper-  
ate equipment without limit stops. Note that SL  
models are supplied without pan limit stops,  
therefore, no adjustments are necessary.  
Factory pan limits are set to 0-355° and tilt limits are to  
0-90° (horizontal to vertical). Under normal conditions,  
the tilt limits should not have to be reset.  
To adjust limit stops, perform the following steps:  
1. Pan to the right using the joystick control until the  
desired pan limit is reached. Remove the drive unit  
from the back box and adjust the pan limit stop  
until the actuator clicks. Lock the limit into posi-  
tion. Replace the drive unit.  
NOTE: FIGURE IS A REPRESENTATION OF AN ACTUAL UNIT  
WITH SOME PARTS NOT SHOWN TO PROVIDE  
CLARITY OF LIMIT STOP LOCATIONS  
Figure 5. Limit Stop Locations  
Pelco Manual C467M-D (5/95)  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.0 CARE AND MAINTENANCE  
If dust or other debris accumulates on the inside of the  
lower dome, remove with clean air pressure only. Com-  
pressed air cans are available from commercial photo-  
graphic equipment and supply dealers.  
Regularly scheduled maintenance will prolong the op-  
erational life and appearance of the equipment.  
IMPORTANT: The lower dome of the en-  
closure is an optical surface. When cleaning the  
inner surface of the dome and viewing window,  
treat as carefully as you would a fine camera  
lens. Do not use water, liquid or spray cleaners  
of any kind on coated inner surface of dome.  
Clean the outer surface of the dome and the inner sur-  
face of the viewing window with a non-abrasive clean-  
ing cloth and anti-static cleaner that is safe for use on  
acrylic plastic. Do not use kerosene or similar sub-  
stances that can scratch the surface.  
LIMIT ACTUATOR  
UP  
DOWN  
LOCKING SCREW  
UP  
FRONT  
DOWN  
Figure 6. Tilt Limit Stop Modification  
10  
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.0 EXPLODED ASSEMBLY DIAGRAM  
Refer to Figure 7 for an exploded assembly diagram of the SB19 enclosure.  
PP ONLY  
NON SL ONLY  
*
**  
EXPASB1900  
EXPASB1900PP  
Figure 7. SB19 Exploded Assembly Diagram  
Pelco Manual C467M-D (5/95)  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST  
Item  
Qty  
Description  
Pelco Part Number  
1
2
3
4
5
6
1
1
1
1
1
2
UL, Pad, camera, black .062" thick  
PCB assembly, pan/tilt  
Bushing, 3/8" tilt shaft  
Shaft, tilt table  
Sprocket .25" bore with pin and SS  
Ball stud receiver  
EH200010004  
PCB3000100ASSY  
PT180010001  
PT18004002COMP  
PT18004003COMP  
PT180410001  
7
Not used  
8
9
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
4
2
2
6
2
1
1
1
1
2
1
1
2
1
Tilt Chain assembly  
Pan Chain assembly  
Tilt shaft, motor side  
PT18041006ASSY  
PT18041007ASSY  
PT18041011WA  
PT18041012WA  
PT18044002COMP  
PT18044055COMP  
PT18044006COMP  
PT18044009COMP  
PT1804410COMP  
PT18044011COMP  
PT18044014COMP  
PT250010004  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
47  
Frame body, weld assembly  
Dome attachment bracket  
Spindle, pan  
Mount, lower pan and tilt  
Bracket, PC1804-B power supply  
Pan motor heat sink mount  
Pan motor heat sink  
Connector spacer, spindle mount  
Bushing  
Bushing, 1/4", tilt shaft  
Sprocket, pan spindle  
Tilt table  
PT250010005  
PT25004104COMP  
PT25004106COMP  
PT25004108COMP  
PT25004121COMP  
PT25004125COMP  
PT350010000  
Tilt limit actuator  
Collar, tilt table switch shaft  
Spricket, 1/4" with SS and pilot  
Bearing, flange  
UL, motor, 4 rpm, 24VAC  
Plate, bearing  
Collar, tilt table motor side  
NP spacer, 1/4" OD x .125, #6 clear  
Switch  
Switch actuator with insulator  
NP cable, S/S x inch  
Connector ring, 14-wire #4 stud  
Coil cord  
Black box assembly, 10.9" octagon  
Trim ring assembly  
Mount, upper pan/tilt  
J-box end  
J-box cover  
PT350010010  
PT35001060COMP  
PT89104001COMP  
SPA8500  
SWI1SM1  
SWIJS138B  
E70810001  
E70810002  
PT180410002  
SB10841010ASSY  
SB18044100COMP  
SB18044105COMP  
SB18044105COMP  
SB18044006COMP  
SSB18044007COMP  
SB18044009COMP  
SB184220COMP  
Boack box mount plate  
BNC panel mount bracket  
8" dome camera/lens position template  
Not used  
4
2
1
Back box mount rail  
SB194002COMP  
TRB-2MV-10  
SB194200COMP  
Terminal block, 10-position PC mount  
Black opaque dome with smoked viewing window  
and mounting studs  
1
Black opaque dome with clear viewing window  
and mounting studs  
SB194300COMP  
12  
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST (continued)  
Item  
Qty  
Description  
Pelco Part Number  
48  
49  
Not used  
Not used  
50  
Not used  
51  
52  
1
Slip ring, 24 circuit for presets  
Not used  
250010000  
53  
Not used  
54  
Not used  
55  
56  
57  
58  
59  
60  
61  
1
1
1
2
2
1
1
Bracket, tilt pot  
Bracket, LPP lens connector  
Gear, 1.875 plastic  
Gear, 1.5 plastic  
Pot, precision 10K  
Gear, spindle feedback, non-SL  
Pan feedback pot  
Not used  
PT18044012COMP  
PT18044013COMP  
PT250010002  
PT250010006  
POTP010.0K  
PT25004114COMP  
PT25004116COMP  
62 thru 70  
71  
2
1
3
Ring snap  
15510000  
2704051COMP  
5804006COMP  
72  
73  
74  
Bracket, pan limit  
Limit stop, pan univ  
Not used  
75  
76  
1
Grommet, neoprene  
Not used  
GRO2172N  
77  
Not used  
78  
79  
80  
1
1
1
Pan limit stop ring  
Bracket, pan limit mount  
Pan limit actuator pin  
PT18044018COMP  
PT18044019COMP  
PT18044020COMP  
Pelco Manual C467M-D (5/95)  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8.0 MODELS  
DD1900  
SB1900-PP  
SB1901-PP  
Same as the SB1900, except this  
package features the factory installed  
preset (PP) option.  
Dome drive unit for SB1900. (UL)  
Dome drive unit for SB1900-PP.  
DD1900-PP  
DD1900-SL  
Same as SB1900-PP except supplied  
with clear viewing slot in the dome  
for virtually zero light loss.  
Dome drive unit for SB1900-SL.  
(UL)  
SB1900SL-PP Same as the SB1900-SL with the  
addition of the preset (PP) option.  
DD1900SL-PP Dome drive unit for SB1900SL-PP.  
SB19  
Drop ceiling discreet surveillance  
enclosure with black opaque lower  
dome with less than 1 f-stop light at-  
tenuation and all aluminum back box  
which mounts above the ceiling.  
(Camera mount supplied.) (UL)  
SB1901SL-PP Same as SB1900SL-PP except sup-  
plied with clear viewing slot in the  
dome for virtually zero light loss.  
9.0 RECOMMENDED CONTROLS  
The following controls are recommended for use with  
the SB1900 Series enclosures.  
SB19-1  
SB1900  
Same as SB19 except supplied with  
clear viewing slot in the dome for  
virtually zero light loss. (UL)  
9.1 MODELS SB1900 AND SB1900-SL  
This system package includes the  
SB19 black opaque dome enclosure  
plus a 24 VAC pan/tilt factory as-  
sembled inside the back box. It pro-  
vides factory pre-wired feedthrough  
for all control functions (i.e., pan/tilt,  
motorized zoom lens, camera power  
(24 VAC) and video).All connections  
are made at the terminal blocks on  
top of the back box, eliminating wir-  
ing harnesses made in the field. This  
feature significantly reduces installa-  
tion time while increasing the reliabil-  
ity and serviceability of the system.  
(UL)  
Hardwire Short-Distance Controls  
for 24 VAC Operation  
MPT24DT  
MPTA24DT  
MLZ6DT  
Desk top joystick control module for  
24 VAC pan/tilts.  
Same as MPT24DT except with auto/  
random scan operation.  
Desk top zoom lens control module  
with auto/manual iris control.  
Desk top enclosure control module  
for 24 VAC camera on/off.  
MEH24DT  
Coaxitron System 2000  
MPT9000CZ  
Desk top Coaxitron transmitter/control  
with pan/tilt joystick, zoom lens, and  
four accessory function controls.  
SB1901  
Same as SB1900 except supplied  
with clear viewing slot in the dome  
for virtually zero light loss. (UL)  
CX9024RXI  
Desk top Coaxitron receiver for 24  
VAC pan/tilts, zoom lens, 24 VAC  
camera power and optional four ac-  
cessory functions. Indoor use.  
SB1900-SL  
SB1901-SL  
Same as the SB1900, except this  
package features 360° continuous  
pan rotation. (UL)  
A9000  
Auto/random scan plug-in module  
for all Coaxitron receivers.  
Same as SB1900-SL except supplied  
with clear viewing slot in the dome  
for virtually zero light loss. (UL)  
CX900TLC  
System test and receiver manual con-  
trol board for Coaxitron receivers  
(plug-in module).  
14  
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9.2 MODELS SB1900, SB1900-SL,  
SB1900-PP AND SB1900SL-PP  
IOP19B1C  
B/W NTSC 6X camera and lens pkg.  
with preset positioning.  
CM7500 Series Coaxitron Matrix Switcher/Control  
System rack mount card cage with  
CPU and power supply. Capable of  
up to 64 inputs and up to 4 monitor  
outputs. (See C584 product specifi-  
cation sheet for details).  
IOP19B1G  
IOP19C1B  
IOP19C1C  
B/W NTSC 10X camera/lens pkg.  
Color NTSC 6X camera and lens pkg.  
Color NTSC 6X camera and lens  
pkg. with preset positioning.  
CM8500 Series Matrix Switcher/Control System ca-  
pable of up to 32 inputs and 16  
monitor outputs. (See C501 product  
specification sheet for details).  
IOP19C1G  
Color NTSC 10X camera and lens pkg.  
WH1900-06  
6 foot wire harness with bare wire on  
one end (for connection to the termi-  
nal blocks in the junction box on top  
of the back box) and a 37 position con-  
nector on the other end (for connec-  
tion to Coaxitron receiver).  
CM9500 Series Coaxitron Matrix Switcher/Control  
System rack mount card cage with  
CPU and power supply. Capable of  
up to 96 inputs and 16 monitor out-  
puts. (See C500 product specification  
sheet for details).  
WH1900-25  
Same as WH1900-06, except 25 feet  
long.  
CX9024RXI-PP Coaxitron indoor receiver for 24 VAC  
pan/tilts, zoom lens, 24 VAC camera  
power and optional four accessory  
functions, with preset option (PP) for  
pan/tilt and lenses (use with models  
SB1900-PP and SB1900SL-PP).  
(Must be used with CM7500/CM9500  
series controls only.)  
11.0 SPECIFICATIONS  
MECHANICAL  
Construction:  
Pan/tilt  
Back box  
Aluminum  
Aluminum  
Lower dome Acrylic hemisphere with a clear,  
distortion-free viewing window  
with no light attenuation factor  
(SB1901 Series) or smoked, distortion-  
free viewing window with less than  
1 f-stop light attenuation (SB1900 Se-  
ries); rotates with the pan/tilt/camera/  
lens  
CX900TLC  
System test and receiver manual con-  
trol board for Coaxitron receivers  
(plug-in module).  
MPT9500  
Desktop controller (coaxitron com-  
patible) with full PTZ, joy stick, 8  
auxiliary functions.  
Maximum  
Camera/Lens  
Size:  
10.0 OPTIONS  
6.5" L x 4.5" W x 3.25" H, including  
BNC (16.51 cm x 11.43 cm x 8.25 cm);  
maximum camera head width is  
2.50" (6.35 cm) (see Figure 3)  
RB24  
Relay box for 24 VAC pan/tilts and  
scanners. Extends operating distance  
(control to relay box) up to a maxi-  
mum of 14,500 feet utilizing 16Awg.  
Max. Camera  
Power Supply  
Size:  
APSB19  
23.75" square faceplate for suspended  
ceiling applications.  
2.5" x 5.0" x 2.5"  
(6.35 cm x 12.7 cm x 6.35 cm)  
APSB19-1  
IOP19B1B  
Same asAPSB19 except black finish.  
B/W NTSC 6X camera and lens pkg.  
Pan:  
0-355° movement in horizontal  
plane (Models SB1900, SB1900-PP)  
360° continuous rotation (Models  
SB1900-SL, SB1900SL-PP)  
Pelco Manual C467M-D (5/95)  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pan Speed:  
Tilt:  
24°/sec ± 1°  
Lens Connector: Hirchmann 6100 type (mate supplied)  
for non-PP models  
-90° movement from horizontal plane  
12°/sec ± .5°  
AMP CPC type (mate supplied) for  
PP models  
Tilt Speed:  
Motors:  
Synchronous type, continuous duty,  
instantaneous reversing  
Maximum Load: 10 lbs (4.6 kg)  
Gearing:  
Chain drive  
Limit Switches:  
Pan  
5 amp, 10 million cycle rating (ex-  
ternal adjustment) on non-SL  
5 amp, 10 million cycle rating (factory  
set)  
Bearings:  
Pan  
Heavy duty ball bearing and Oilite  
bronze bushing  
Tilt  
Tilt  
Oilite bronze bushing  
Conductor  
Requirements:  
Non-PP  
Braking:  
Friction  
ELECTRICAL  
Input Voltage:  
models  
Pan/tilt (5 plus ground), Lens (4),  
Camera AC (2), Video (coax), Cam-  
era Sync (coax)  
24 VAC required for pan/tilt  
Power  
Requirements:  
Pan  
PP models  
Pan/tilt (9 plus ground), Lens (6),  
Camera AC (2), Video (coax), Cam-  
era Sync (coax)  
.31 amp (7.5 vA)  
.31 amp (7.5 vA)  
Tilt  
GENERAL  
Connectors:  
Terminal strips inside J-box on the top of  
the back box (all functions except video:  
camerapower, lens, pan/tiltandpresets).  
Environment:  
Indoor  
Temperature  
Range:  
Video  
14°F to 122°F (-10°C to +50°C)  
Connector:  
BNC  
Dimensions:  
See Figure 8  
Camera Power: Spade lugs, 24 VAC  
9.25  
(23.50)  
1.65  
(4.19)  
1.80  
(4.58)  
A
7.93  
(20.14)  
3.10  
(7.87)  
11.00  
(27.94)  
B
C
C
B
A
WHERE:  
8.50  
(21.59)  
A
B
C
10.90 (27.69)  
7.70 (19.56)  
12.50  
(31.75)  
3.20  
(8.13)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES.  
Figure 8. SB19 Dimension Drawing  
16  
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12.0 WARRANTY AND RETURN  
INFORMATION  
WARRANTY  
RETURNS  
Pelco will repair or replace, without charge, any merchandise proved  
defectiveinmaterialorworkmanshipforaperiodofoneyearafterthedate  
of shipment.  
In order to expedite parts returned to the factory for repair or credit, please  
call the factory at (800) 289-9100 or (559) 292-1981 to obtain an  
authorization number (CA number if returned for credit, and RA number  
if returned for repair).  
Exceptions to this warranty are as noted below:  
All merchandise returned for credit may be subject to a 20% restocking  
and refurbishing charge.  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and  
keyboard).  
Three years on Camclosure® and fixed camera models, except the  
CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2,  
and MC3651H-2X camera models, which have a five-year warranty.  
Goods returned for repair or credit should be clearly identified with the  
assigned CA or RA number and freight should be prepaid. Ship to the  
appropriate address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto  
Rico, send goods to:  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and  
DF5/DF8 Series fixed dome products.  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, includ-  
ing when used in continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding  
wiper blades).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto  
Rico and are instructed to return goods to the USA, you may do one of the  
following:  
Eighteen months on DX Series digital video recorders, NVR300  
Series network video recorders, and EnduraSeries distributed  
network-based video products.  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
One year (except video heads) on video cassette recorders (VCRs).  
Video heads will be covered for a period of six months.  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods  
to:  
Six months on all pan and tilts, scanners or preset lenses used in  
continuousmotionapplications(thatis,presetscan,tourandautoscan  
modes).  
Pelco c/o Expeditors  
473 Eccles Avenue  
Pelco will warrant all replacement parts and repairs for 90 days from the  
date of Pelco shipment. All goods requiring warranty repair shall be sent  
freight prepaid to Pelco, Clovis, California. Repairs made necessary by  
reason of misuse, alteration, normal wear, or accident are not covered  
under this warranty.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
Pelco assumes no risk and shall be subject to no liability for damages or  
loss resulting from the specific use or application made of the Products.  
Pelco’s liability for any claim, whether based on breach of contract,  
negligence, infringement of any rights of any party or product liability,  
relating to the Products shall not exceed the price paid by the Dealer to  
Pelco for such Products. In no event will Pelco be liable for any special,  
incidental or consequential damages (including loss of use, loss of profit  
and claims of third parties) however caused, whether by the negligence  
of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The  
Dealer may also have additional rights, which are subject to variation from  
state to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800)  
289-9100 or (559) 292-1981 to obtain a Repair Authorization number  
(RA), and provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice  
number  
3. Details of the defect or problem If there is a dispute regarding the  
warranty of a product which does not fall under the warranty conditions  
stated above, please include a written explanation with the product  
when returned.  
Method of return shipment shall be the same or equal to the method by  
which the item was received by Pelco.  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union  
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.  
Pelco Manual C467M-D (5/95)  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pelco  
3500 Pelco Way • Clovis, CA 93612-5699  
(559) 292-1981 • (800) 289-9100  
FAX (800) 289-9150 or (559) 292-3827  
International customers call 1-559-292-1981 or FAX 1-559-348-1120  
(Product specifications subject to change without notice.)  
18  
Pelco Manual C467M-D (5/95)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Philips DVD Player DVD 691 User Manual
Philips DVD Player PET714 User Manual
Philips Range 1145AZ User Manual
Philips TV DVD Combo TV DVD User Manual
Phoenix Gold Speaker hoenix Gold Innovative Home ATC Dual Mono DM In Ceiling Speaker System User Manual
Pioneer Car Video System AVX 7300 User Manual
Porter Cable Air Compressor D24938 044 2 User Manual
Profile Speaker BX12 User Manual
ProForm Home Gym PFEL03900 User Manual
ProForm Treadmill 1290 zlt User Manual