®
PT780 Legacy® Series
Pan and Tilts
Maintenance/
Service Manual
C342SM (12/98)
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 • DataFAX (1-559) 292-0435
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 GENERAL
1.1 IMPORTANT SAFEGUARDS AND WARNINGS
Observe the following WARNINGS before installing and using this product.
1. Installation and servicing should be done by qualified service personnel only,
and should conform to all local codes.
2. The weight of the camera/lens and enclosure must not exceed 40 lb (18.14 kg)
with 12 VDC pan and tilts or 52 lb (23.59 kg) with 24 VAC or 120 VAC pan and
tilts.
3. Only use replacement parts Pelco recommends.
4. After replacing/repairing this unit’s electrical components, conduct a resistance
measurement between line and exposed parts to verify the exposed parts
have not been connected to line circuitry.
5. Installation methods and materials should be capable of supporting four times
the combined weight of the enclosure, pan and tilt, camera, and lens.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
CAUTION:
RISK OF
ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information
in this manual prior to installation and operation.
Pelco Manual C342SM (12/98)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 DESCRIPTION
2.1 PT780 DESCRIPTION
The PT780 Series pan and tilt units are designed for medium duty, indoor/outdoor
use.
Only Legacy® Series enclosures can be mounted on the pan and tilt units. These
enclosures are the EH4700L and EH5700L environmental enclosures and the
EH8106L pressurized enclosure.
You can easily remove the clamshell covers from the sides of the pan and tilt units
to access all internal parts without having to remove the camera enclosure. This
makes servicing the units and adjusting the pan and tilt limit stops easy.
2.2 PT780 MODELS
The PT780 Series consists of the following models:
PT780P
Heavy-duty, indoor/outdoor pan and tilt, 120 VAC.
PT780P/PP
PT780-SL
PT780SL/PP
PT780VS
PT780P with preset positioning capabilities.
PT780P with 360° pan rotation.
PT780SL with preset positioning capabilities.
Heavy-duty, indoor/outdoor, variable-speed pan and tilt, 12
VDC.
PT780VS/PP
PT780-VSSL
PT780-VSSL/PP
PT780-24P
PT780VS with preset positioning capabilities.
PT780VS with 360° pan rotation.
PT780-VSSL with preset positioning capabilities.
Heavy-duty, indoor/outdoor pan/tilt, 24 VAC.
PT780-24P with preset positioning capabilities.
PT780-24P with 360° pan rotation.
PT780-24P/PP
PT780-24SL
PT780-24SL/PP
PT780-24SL with preset positioning capabilities.
4
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 MAINTENANCE
If you need to remove the enclosure, protect the RediLINK™ connector area against
moisture, dust, dirt, etc. Failure to do so could result in a bad connection. Also,
damage to the pan and tilt unit or enclosure could occur when power is turned on.
The following servicing should be done every six months with average use.
1. Remove the PT780’s outer casing.
a. Remove the Phillips screw on each side of the pan and tilt unit.
b. Place your hands under the cover halves. Exert a strong, upward force
to release the covers from their internal latching devices.
c. Pull the cover halves away from the pan and tilt unit. Set the covers down
or hang them by the eyelets inside the covers. (The wire and hook on
which to hang the covers is not provided.)
2. Inspect the gaskets around the cover, tilt shaft, and spindle for damage.
3. Refer to Figure 1. It shows the parts locations of the tilt assembly. Look for
similar orientations of parts when adjusting the pan assembly.
4. Check the backlash adjustment.
Backlash is the slack or binding in a pan and tilt base mount. Determine back-
lash by lifting the maintenance assembly, grasping the base, and wiggling it.
There should not be any play or binding between the gear (A) and worm drive
(B). Play or binding indicates a backlash problem.
•
•
One backlash problem involves a worm and worm gear connection loose
enough to cause slipping or tight enough to cause binding.
The second involves a too-loose or too-tight chain, usually causing symp-
toms similar to the worm and worm gear problem–slipping or binding.
a. Verify that the worm drive (B) is fully seated in the worm gear (A). If it is not:
(1) Locate the worm-driven gear for either the pan or the tilt motor link-
age. Loosen the three hex screws (F) holding the worm in place,
but leave enough thread in place to hold the assembly on the mount.
(2) Using your thumbs, gently move the worm forward or pull the as-
sembly back from the worm gear to either tighten or loosen the gear
spacing to the worm gear. Move the base of the pan and tilt to check
the adjustment.
(3) If you get movement in the base, press a finger down in the middle
of the worm assembly. If you get no movement in the base, use
your thumb and forefinger to pull the worm assembly back until you
get movement.
(4) When the spacing is correct, tighten the hex screws. Start with the
middle screw to ensure proper spacing.
(5) Remove the screw (C) in the gear train nut (D).
(6) Tighten the gear train nut to remove any play.
(7) Line up the hole in the gear train nut with the nearest hole in the
gear train bracket (E).
(8) Replace the screw.
Pelco Manual C342SM (12/98)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
b. Refer to Figure 1. Adjust chain tension, if needed:
(1) Locate the pan or tilt motor on the assembly. Loosen the hex screws
(G) that hold the motor to its mounting bracket. Depending on which
motor assembly you are adjusting, there will be either three (pan) or
four (tilt). (Only two screws are shown in Figure 1.)
(2) Using a screwdriver, pry the motor down (at H) to tighten for the
correct chain tension. (You should not be able to freely move the
motor with your finger, nor should it be so tight that it will not move
at all as this usually leads to binding.)
(3) Tighten the hex screws.
c. Using a controller, you should now be able to move the PT780 without
looseness or binding. If you have any problems, contact Pelco’s Techni-
cal Support Department.
5. Lubricate the chains. Use a Teflon chain lubricant, such as TriFlon™.
6. Replace the covers.
a. Grasp one cover half in each hand and position the covers on each side
of the pan and tilt unit.
b. Bring the two cover halves together, aligning the two pins in one cover
half with the mating holes in the other cover half.
c. When the cover halves are together, press downward to force the covers
into their latches.
d. Replace the screws in the covers.
H
G
Figure 1. Pan and Tilt Adjustments
6
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 WIRING DIAGRAMS
Figure 2. PT780 Series Wiring Diagram
Pelco Manual C342SM (12/98)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 EXPLODED ASSEMBLY DIAGRAMS
Figure 3. Exploded Assembly Diagram of Mechanical Parts–PT780 Series 24 VAC and 120 VAC Models
8
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
12
9
10
11
17
13
16
60
8
18
19
20
21
6
22
7
23
24
63
4
14
64
15
62
41
26
25
40
27
61
46
53
15
57
3
51
50
14
59
58
6
2
1
29
39
61
54
47
31
49
44
48
33
46
45
38
34
37
21
42
22
21
43
36
35
56
55
Figure 4. Exploded Assembly Diagram of Mechanical Parts–PT780 Series 12 VDC Models
Pelco Manual C342SM (12/98)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Table A. Mechanical Parts List (Figure 3 and Figure 4)
Refer to Figure 12 for 24 VAC and 120 VAC models.
Refer to Figure 13 for 12 VDC models.
Item
Quantity
Description
Part Number
1
2
3
4
1
2
2
1
Cover, pan side
Ball stud
Ball stud bracket
Pan motor, 24 VAC
9064003COMP
PT180410000
9064010COMP
5708007
Pan motor, 120 VAC
1758005
Pan motor with gearhead, 12 VDC
Pan motor gearhead, 24 VAC and 120 VAC
Not used, 12 VDC
Pan motor sprocket, 24 VAC and 120 VAC
Pan motor sprocket, 12 VDC
Pan motor bracket, 24 VAC and 120 VAC
Pan motor bracket, 12 VDC
Tilt preset potentiometer
Tilt potentiometer bracket
Gear, 32 teeth
9068102
1758006
5
6
7
1
1
1
5804010ACOMP
9004007COMP
9064006COMP
9064060COMP
POTP010.0K*
9064012COMP*
28010017*
8
9
1
1
1
1
1
10
11
12
13
14
Gear, 52 teeth
Tilt limit ring
Tilt limit stop
Actuator, with insulator
28010016*
9004012COMP
1554050COMP
SWIJS138B
2
4
2**
4
15
Switch
SWI1SM1
2**
1
1
1
1
1
5
3
1
1
1
1
1
16
17
18
19
20
21
22
23
24
25
26
27
Upright, pan side
Bushing, pan side
9064002COMP
PT250010004
COND226S
9004015COMP
9004000COMP
90010002
90010001
90010024
90010006
26-pin, subminiature, D-type socket
Tilt shaft connector guide
Tilt shaft feed-through
Thrust washer, .030"
Thrust bearing
Thrust washer, .060"
Bronze bushing
Cross-brace uprights
Upright, tilt side
9064008COMP
9064001COMP
90010009
Worm gear, 40 teeth
9004024COMP***
9004025COMP****
90010028
28
29
1
1
Sprocket, 24 VAC and 120 VAC
Not used, 12 VDC
Tilt motor, 24 VAC
5808000
1758005
9068101
5808001
1758006
Tilt motor, 120 VAC
Tilt motor with gearhead, 12 VDC
Tilt motor gearhead, 24 VAC
Tilt motor gearhead, 120 VAC
Not used, 12 VDC
30
1
31
32
1
1
Tilt motor bracket, 24 VAC and 120 VAC
Tilt motor bracket, 12 VDC
Sprocket, 24 VAC
9064005COMP
9064059COMP
5804022COMP
7512004
Sprocket, 120 VAC
Not used, 12 VDC
33
1
Circuit board assembly, 24 VAC
Circuit board assembly, 120 VAC
Circuit board assembly, 12 VDC
Cover, tilt side
PCB9061000ASSY
PCB9061120ASSY
PCB9061001ASSY
9064004COMP
34
35
1
1
Pan spindle
9004030COMP
*
PP models only
*** SL/PP model only
**** Non-360° PP models
** All SL models
Continued on next page
10
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
Table A. Mechanical Parts List (Figure 3 and Figure 4) (continued)
Item
Quantity
Description
Part Number
36
37
38
39
40
3
1
1
1
1
Pan limit stop
Bronze bushing
Base
Pan limit stop
Slip ring
5804006COMP*****
90010029
9064007COMP
1554049COMP*****
250010000***
28010000******
9004017COMP***
9004022COMP****
9004008COMP
90010020*
POTDARM010.0K***
POTP010.0K****
9004009COMP
5806005
5806003
5806002
90010008
9004005COMP
9004006COMP
PT18004003COMP
41
1
Preset gear, pan spindle
42
43
44
1
1
1
Pan potentiometer bracket
Gear, 56 teeth
Pan preset potentiometer
45
46
47
48
49
50
51
52
2
4
8
4
2
2
1
1
Gear train nut
Bronze bushing
Thrust washer
Thrust bearing
Worm
Gear train bracket
3-position bar nut
Sprocket, 24 VAC and 120 VAC
Not used, 12 VDC
Pan spindle nut
Ball stud receiver
Grommet, 3/8" ID
Grommet, 1/4" ID
Wire clamp
53
54
55
1
2
1
9004019COMP
90010030
GRO2175
GRO2170**
56
1
9004020COMP*****
9004021COMP**
9004023COMP
15510000*****
1554051COMP*****
90010017
GRO2172N*****
9064015COMP
9064014COMP
90010009
57
58
59
60
61
62
63
64
2
2
1
1
1
1
1
1
Eyelet service bracket
Snap ring
Pan limit switch bracket
Wave spring
Grommet
Unthreaded backup plate
Threaded backup plate
Worm gear
The following items are not shown:
65
1
1
Pan chain assembly, 29 pitch,
9061002ASSY
24 VAC and 120 VAC
Pan chain assembly, 32 pitch, 12 VDC
Tilt chain assembly, 35 pitch,
24 VAC and 120 VAC
9061013ASSY
9061003ASSY
66
Tilt chain assembly, 28 pitch, 12 VDC
2-position plastic connector
3-position plastic connector
6-position plastic connector
Cover labels
9061008ASSY
CON640428-2
CON640428-3
CON640428-6
LBL19000
67
68
69
70
71
1
6
1
2
1
Dust protector, 26-pin, subminiature,
D-type socket
90010025
72
73
74
75
1
37
1
37-pin connector plug (installed on cable)
Connector pins
Cable connector clamp
37-pin connector socket assembly
(loose equipment)
CON206305-1
CON66400-1
CON206138-1
CONA37S
1
Includes 37-position housing, boot,
sockets, cable clamp
*
PP models only
**** Non-360° PP models
***** Not on SL models
****** SL model
** All SL models
*** SL/PP model only
Pelco Manual C342SM (12/98)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
K
I
L
J
G
I
H
FF
J
E
EE
F
E
M
F
PP
D
S
C
T
B
A
AA
Q
N
NN
J
O
W
N
M
BB
EE
CC
J
E
F
Q
I
J
J
W
T
S
BB
R
W
J
W
J
A*
B*
C*
D*
P
HH
II
JJ
DD
E
F
KK
T
S
Y
Z
GG
X
LL
V
U
MM
J
I
Figure 5. Exploded Assembly Diagram of Hardware–PT780 Series 24 VAC and 120 VAC Models
12
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
I
K
J
L
I
G
J
H
FF
E
EE
F
E
F
M
A
F
PP
B
S
T
AA
NN
D
N
J
W
N
EE
M
BB
CC
J
E
F
BB
I
J
J
W
T
S
J
BB
R
W
W
J
B
F
A
P
DD
Z
E
F
T
S
Y
GG
X
LL
V
U
MM
J
I
Figure 6. Exploded Assembly Diagram of Hardware–PT780 Series 12 VDC Models
Pelco Manual C342SM (12/98)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Table B. Hardware Parts List (Figure 5 and Figure 6)
Refer to Figure 14 for 24 VAC and 120 VAC models.
Refer to Figure 15 for 12 VDC models.
Item
Quantity
Description
Part Number
A
4
8
4
4
8
4
4
8
Screw, 6-32 x 2 1/2", pan head, Phil, 24 VAC
Screw, 8-32 x 2 1/2", pan head, Phil, 120 VAC
Screw, 10-32 x 1/2", pan head, Phil, 12 VDC
Flat washer, 24 VAC
Flat washer, 120 VAC
Flat washer, 12 VDC
Split lock washer, #6, 24 VAC
Split lock washer, #8, 120 VAC
Not used, 12 VDC
Hex nut, 6-32, 24 VAC
Hex nut, 8-32, 120 VAC
ZH6-32X2.50SPP
ZH8-32X2.50CPS
ZH10-32X.500SPP
ZH932X1.75X130
ZH932X1.75X130
ZH240X436X60C
ZH6LWSSL
B
C
D
ZH8LWSSL
4
8
ZH6-32NUTSH
ZH8-32NUTSH
Not used, 12 VDC
E
F
12
11
12
15
3
Allen screw, 10-32 x 3/8", 24 VAC and 120 VAC
Allen screw, 10-32 x 3/8", 12 VDC
Split lock washer, #10, 24 VAC and 120 VAC
Split lock washer, #10, 12 VDC
Screw, 2-56 x 3/8", pan head, Phillips
Internal star washer, #2
ZH10-32X.375SSS
ZH10LWSSL
G
H
ZH2-56X.375SRS
ZH2LWSIS
3
I
J
K
L
9
25
2
Screw, 4-40 x 3/8", pan head, Phillips
Internal star washer, #4
Screw, 8-32 x 1/4", pan head, Phillips
Internal star washer, #8
ZH4-40X.375SPP
ZH4LWSIS
ZH8-32X.250SPP
ZH8LWSIS
2
M
N
O
P
Q
R
S
T
8
12
2
2
2
Screw, 2-56 x 7/16", pan head, Phillips
Screw, 6-32 x 1/2", flat head, Phillips
Bolt, 1/4-20 x .625", flat head, Phillips
Screw, 4-40 x 5/8", pan head, Phillips
Roll pin (Not shown in Figure 15)
Allen bolt, 1/4-20 x 1/2"
Flat washer, 1/4
Split lock washer, 1/4
Screw, 10-32 x .875", gray
Thread sealing washer
ZH2-56X.437SPP
ZH6-32X.500FPF
ZH1/420X.625SFS
ZH4-40X.625SPP
ZHPIN3/32X3/4R
ZH1/420X1.50SS
ZH260X562X65C
ZH1/4LWSSL
6
11
11
2
U
V
ZH10-32X.875GRY
PS3010002
2
W
X
Y
14
2
3
3
2
2
2
2
1
1
1
4
4
4
4
1
1
Screw, 4-40 x .250", pan head, Phillips
Screw, 6-32 x .375", pan head, Phillips
Allen bolt, 1/4-20 x 3/4"
Bolt, 1/4-20 x 3/4", flat head, Phillips
Self-tapping screw, 6-32
Roll pin
Allen screw, 4-40 x .250"
Dowel pin
Cover gasket
ZH4-40X.250SPP
ZH6-32X.375SPP
ZH1/420X.750SS
ZH1/420X.750SFS
ZH6-SAX.250CPP
ZHPIN3/32X1/2R
ZH4-40X.250SS
90010004
Z
AA
BB
CC
DD
EE
FF
GG
HH
II
JJ
KK
LL
MM
NN
PP
90610010
90010014
Tilt shaft gasket
Set screw, 6-32 x 3/16"
ZH6-32X.187S
ZH8-32X2.50CPS
ZH932X1.75X130
ZH8LWSSL
ZH8-32NUTSH
90010003
90010012
ZH10-32X.750SPP
ZH1/420X.625CS
Screw, 8-32 x 2 1/2", pan head, Phillips, 24 VAC only
Flat washer, 24 VAC only
Split lock washer, #8, 24 VAC only
Hex nut, 8-32, 24 VAC only
Spindle cover gasket
Spindle mount gasket
Screw, 10-32 x 3/4", pan head, Phillips
Allen bolt, 1/4-20 x .625"
3
2
14
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
Pelco Manual C342SM (12/98)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment. Excep-
tions to this warranty are as noted below:
•
•
•
Three years on Genex™ Series (multiplexers, server, and keyboard).
Two years on all standard motorized and fixed focal length lenses.
Two years on Legacy®, Intercept®, PV1000 Series, CM6700/CM8500/CM9500/
CM9750/CM9760 Matrix, Spectra®, DF5 Series and DF8 Fixed Dome products.
Two years on WW5700 series window wiper (excluding wiper blades).
Two years on cameras.
•
•
•
Six months on all pan and tilts, scanners or preset lenses used in continuous
motion applications (that is, preset scan, tour and auto scan modes).
Pelco will warranty all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid to
Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration,
normal wear, or accident are not covered under this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss result-
ing from the specific use or application made of the Products. Pelco’s liability for
any claim, whether based on breach of contract, negligence, infringement of any
rights of any party or product liability, relating to the Products shall not exceed the
price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable
for any special, incidental or consequential damages (including loss of use, loss of
profit and claims of third parties) however caused, whether by the negligence of
Pelco or otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under
the warranty conditions stated above, please include a written explanation with the
product when returned.
Ship freight prepaid to:
Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the
factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA
number if returned for credit, and RA number if returned for repair). Goods returned
for repair or credit should be clearly identified with the assigned CA/RA number and
freight should be prepaid. All merchandise returned for credit may be subject to a
20% restocking and refurbishing charge.
®Pelco and the Pelco logo are
registered trademarks of Pelco.
©Copyright 1998, Pelco. All rights
reserved.
Ship freight prepaid to:
Pelco
300 West Pontiac Way
Clovis, CA 93612-5699
16
Pelco Manual C342SM (12/98)
Download from Www.Somanuals.com. All Manuals Search And Download.
|