®
PMC14E Series High-Resolution
14-Inch Color Monitors
Installation/Operation Manual
C929M-B (2/97)
Pelco • 3500 Pelco Way, Clovis, CA 93612-5699 • USA • (800) 289-9100 or (1-559) 292-1981
FAX (800) 289-9150 or (1-559) 292-3827
International customers call 1-559-292-1981 or FAX 1-559-348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
1.0 GENERAL
1.1 IMPORTANT SAFEGUARDS AND WARNINGS
Prior to installation and use of this product, the following WARNINGS should be
observed.
1. Installation and servicing should only be done by Qualified Service Personnel
and conform to all Local codes.
2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X ,6 or
6P enclosure, it is designed for Indoor use only and it must not be installed
where exposed to rain and moisture.
4. Only use replacement parts recommended by Pelco.
5. After replacement/repair of this unit’s electrical components, conduct a resis-
tance measurement between line and exposed parts to verify the exposed
parts have not been connected to line circuitry.
The product may bear the following marks:
This symbol indicates that dangerous voltage constituting a
risk of electric shock is present within this unit.
This symbol indicates that there are important operating and
maintenance instructions in the literature accompanying this
unit.
CAUTION:
RISK OF
ELECTRIC SHOCK.
DO NOT OPEN.
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER-
SERVICEABLE PARTS INSIDE. REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
Please thoroughly familiarize yourself with the information
in this manual prior to installation and operation.
Pelco Manual C929M-B (2/97)
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1.1 IMPORTANT SAFEGUARDS
1. Read Instructions - All the safety and operating instructions should be read
before the unit is operated.
2. Retain Instructions - The safety and operating instructions should be retained
for future reference.
3. Heed Warnings - All warnings on the unit and in the operating instructions
should be adhered to.
4. Follow Instructions - All operating and use instructions should be followed.
5. Cleaning - Unplug the unit from the outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
6. Attachments - Do not use attachments not recommended by the product manu-
facturer as they may cause hazards.
7. Water and Moisture - Do not use this unit near water - for example, near a bath
tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, near a swim-
ming pool, in an unprotected outdoor installation, or any area which is classi-
fied as a wet location.
8. Accessories - Do not place this unit on an unstable stand, tripod, bracket, or
mount. The unit may fall, causing serious injury to a person and serious dam-
age to the unit. Use only with a stand, tripod, bracket, or mount recommended
by the manufacturer, or sold with the product. Any mounting of the unit should
follow the manufacturer’s instructions, and should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart com-
bination to overturn.
9. Ventilation - Openings in the enclosure, if any, are provided for ventilation and
to ensure reliable operation of the unit and to protect it from overheating. These
openings must not be blocked or covered. This unit should not be placed in a
built-in installation unless proper ventilation is provided or the manufacturer's
instructions have been adhered to.
10. Power Sources - This unit should be operated only from the type of power
source indicated on the marking label. If you are not sure of the type of power
supply you plan to use, consult your appliance dealer or local power company.
For units intended to operate from battery power, or other sources, refer to the
operating instructions.
11. Grounding or Polarization - This unit may be equipped with a polarized alter-
nating-current line plug (a plug having one blade wider than the other). This
plug will fit into the power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the plug. If the plug
should still fail to fit, contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
Alternately, this unit may be equipped with a 3-wire grounding-type plug, a
plug having a third (grounding) pin. This plug will only fit into a grounding-type
power outlet. This is a safety feature. If you are unable to insert the plug into
the outlet, contact your electrician to replace your obsolete outlet. Do not de-
feat the safety purpose of the grounding-type plug.
12. Power-Cord Protection - Power supply cords should be routed so that they are
not likely to be walked on or pinched by items placed upon or against then,
paying particular attention to cords and plugs, convenience receptacles, and
the point where they exit from the appliance.
2
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
13. Power Lines - An outdoor system should not be located in the vicinity of over-
head power lines or other electric light or power circuits, or where it can fall
into such power lines or circuits. When installing an outdoor system, extreme
care should be taken to keep from touching such power lines or circuits as
contact with them might be fatal. U.S.A. models only - refer to the National
Electrical Code Article 820 regarding installation of CATV systems.
14. Overloading - Do not overload outlets and extension cords as this can result in
a risk of fire or electric shock.
15. Object and Liquid Entry - Never push objects of any kind into this unit through
openings as they may touch dangerous voltage points or short-out parts that
could result in a fire or electric shock. Never spill liquid of any kind on the unit.
16. Servicing - Do not attempt to service this unit yourself as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all ser-
vicing to qualified service personnel.
17. Damage Requiring Service - Unplug the unit from the outlet and refer servic-
ing to qualified service personnel under the following conditions:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instruc-
tions. Adjust only those controls that are covered by the operating in-
structions, as an improper adjustment of other controls may result in dam-
age and will often require extensive work by a qualified technician to
restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f.
When the unit exhibits a distinct change in performance - this indicates a
need for service.
18. Replacement Parts - When replacement parts are required, be sure the ser-
vice technician has used replacement parts specified by the manufacturer or
have the same characteristics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
19. Safety Check - Upon completion of any service or repairs to this unit, ask the
service technician to perform safety checks to determine that the unit is in
proper operating condition.
20. Coax Grounding - If an outside cable system is connected to the unit, be sure
the cable system is grounded. U.S.A. models only-Section 810 of the National
Electrical Code, ANSI/NFPA No.70-1981, provides information with respect to
proper grounding of the mount and supporting structure, grounding of the coax
to a discharge unit, size of grounding conductors, location of discharge unit,
connection to grounding electrodes, and requirements for the grounding elec-
trode.
21. Lightning - For added protection of this unit during a lightning storm, or when
it is left unattended and unused for long periods of time, unplug it from the wall
outlet and disconnect the cable system. This will prevent damage to the unit
due to lightning and power-line surges.
Pelco Manual C929M-B (2/97)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2.0 DESCRIPTION
The PMC14E Series provides 14-inch (36 cm), color, high-resolution monitors.
Monitor Features
•
Two video and audio input channels (one passive) with looping output. Video
inputs include connectors for either a standard composite video signal or Y/C
(Super VHS) signal.
•
•
•
•
•
•
•
Manual or automatic switching between channels with adjustable dwell time
Video tape recorder input and output
High resolution 480 lines
Comb filter for improved picture quality
120 VAC or 230 VAC operation
NTSC or PAL video format
Controls for contrast, brightness, color, sharpness, tint, dwell time, channel
selection, volume, and power
•
•
Steel cabinet
Manufactured in accordance with EMC Directive, 89/336/EEC
2.1 MODELS
PMC14E
14-inch color monitor, 120 VAC, NTSC format
14-inch color monitor, 230 VAC, PAL format
PMC14EX
2.2 OPTIONAL ACCESSORIES
RMA14E-BK
Rack-mount kit for mounting one monitor in a 19-inch (48.26 cm)
wide rack. Black finish.
RMA14E-GY
Same as RMA14E-BK except gray.
IN
OUT
75 ohm
HIGH
INPUT 2
OUTPUT
VTR
VIDEO
INPUT 1
VIDEO
AUDIO
VIDEO 2
VIDEO
AUDIO
AUDIO
AUDIO
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
Figure 1. Rear Panel Connectors
4
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
3.0 INSTALLATION
3.1 BACK PANEL CONNECTIONS
Refer to Table A for the type of video coaxial cable to use.
Refer to Figure 1 for rear panel connections.
CAUTION: Do not install
this monitor in an exces-
sively hot location, or in any
way obstruct the ventilation
openings in the cabinet. Pre-
mature component failure or
damage to the cabinet may
result.
Connect equipment to the monitor as follows. There are several options for inputs 1
and 2 as shown on this and the following pages. Select the appropriate one.
Table A. Video Coaxial Cable Wiring Distances
Cable Type
Maximum Distance
RG59
RG6
RG11
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m )
Inputs 1 and 2 (Camera Inputs)
1. Refer to Figure 2. Connect cameras and audio equipment to the inputs 1 and/
or 2. Note that each input has two video connectors: a BNC connector for a
standard composite video signal and a four-pin jack for a Y/C signal input. The
Y/C input provides luminance (Y) and chrominance (C) signal input from Su-
per VHS equipment.
NOTE:Do not connect equipment
to both the BNC and Y/C connec-
tors on the same input. If the moni-
tor senses a signal at both connec-
tors, the Y/C input will be selected.
2. Set the 75-ohm/HIGH switch for 75 ohms if you are using Input 1.
CAMERA ONE
CAMERA TWO
SET FOR 75 OHMS
IN
OUT
75 ohm
HIGH
INPUT
2
OUTPUT
VIDEO
INPUT
1
VIDEO
AUDIO
VIDEO
2
VIDEO
AUDIO
AUDIO
AUDIO
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
Figure 2. Camera Inputs
Pelco Manual C929M-B (2/97)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Input 1 or 2 (Input from Switcher or Matrix Control System - Video
Only)
1. Refer to Figure 3. Connect the video output from the video switcher or matrix
control equipment to Input 1 or Input 2 on the output monitor.
2. Set the 75-ohm/HIGH switch for 75 ohms if you are using Input 1.
OUTPUT MONITOR
VIDEO SWITCHER
OR MATRIX
SET FOR 75 OHMS
IN
OUT
75 ohm
HIGH
INPUT
2
OUTPUT
VIDEO
INPUT
1
VIDEO
AUDIO
VIDEO
2
VIDEO
AUDIO
AUDIO
AUDIO
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
Figure 3. Input from Switcher or Matrix Control System
Input 1 (Dedicated Monitor Application - Video Only with Pan/Tilt/
Zoom Control)
Refer to Figure 4. This configuration allows you to use Pelco's Coaxitron® control
system to operate pan, tilt, and zoom functions The control signals are transmitted
over the video coax cable.
1. Connect the video cable from the Coaxitron® receiver to the IN connector of
Input 1 on the feed monitor. Connect another video cable from the OUT con-
nector of the feed monitor to the video switcher or matrix control equipment.
2. Set the 75-ohm/HIGH switch for HIGH.
VIDEO SWITCHER
OR MATRIX
VIDEO INPUT
SET FOR HIGH
COAXITRON®
RECEIVER
IN
OUT
75 ohm
HIGH
INPUT
2
OUTPUT
VIDEO
INPUT
1
VIDEO
AUDIO
VIDEO
2
VIDEO
AUDIO
AUDIO
AUDIO
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
VIDEO OUTPUT
FEED MONITOR
Figure 4. Dedicated Monitor Application with Pan/Tilt/Zoom Control
6
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
Input 1 (Dedicated Monitor Application - Video Only, No Camera
Control)
1. Refer to Figure 5. Connect the video cable from the camera to the IN connec-
tor of Input 1 on the feed monitor. Connect another video cable from the OUT
connector of the feed monitor to the video switcher or matrix control equip-
ment.
2. Set the 75-ohm/HIGH switch for HIGH.
FEED MONITOR
VIDEO SWITCHER
OR MATRIX
VIDEO INPUT
SET FOR HIGH
IN
OUT
75 ohm
HIGH
IUT
2
OUTPUT
VIDEO
INPUT
1
VIDEO
AUDIO
VIDEO
2
VIDEO
AUDIO
AUDIO
AUDIO
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
Figure 5. Dedicated Monitor Application with No Control
Output Connections
Refer to Figure 6. To loop the video and audio signals from the monitor to another
monitor, connect cables from the OUTPUT connectors of the monitor to the INPUT
1 or INPUT 2 connectors of the next monitor.
SET FOR 75 OHMS
SET FOR 75 OHMS
IN
OUT
75 ohm
HIGH
IN
OUT
75 ohm
HIGH
INPUT
2
OUTPUT
INPUT
2
OUTPUT
VIDEO
INPUT
1
VIDEO
INPUT
1
VIDEO
AUDIO
VIDEO
2
VIDEO
VIDEO
AUDIO
VIDEO
2
VIDEO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AUDIO
AC INPUT
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
INPUT
OUTPUT
Figure 6. Output Connections
Pelco Manual C929M-B (2/97)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
VTR Connections
Refer to Figure 7. Connect the video and audio connections from the monitor to a
video recorder if desired.
Power
Plug the appropriate end of the power cable into theAC INPUT on the monitor. Plug
the other end into a utility outlet.
IN
OUT
75 ohm
HIGH
INPUT
2
OUTPUT
VIDEO
INPUT
1
VIDEO
AUDIO
VIDEO
2
VIDEO
AUDIO
AUDIO
AUDIO
AC INPUT
INPUT
OUTPUT
INPUT
OUTPUT
VIDEO IN
VIDEO OUT
AUDIO IN
AUDIO OUT
Figure 7. VTR Connections
8
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
3.2 FRONT PANEL CONTROLS
Refer to Figure 8. Set the controls on the front panel of the monitor as follows:
1. Set the PAL/NTSC switch for NTSC video format if you have a PMC14E moni-
tor. Set the switch for PAL video format if you have a PMC14EX monitor.
2. Set the VTR/VIDEO switch for the signal input that you are using.
•
•
Select VTR if you want to play a VCR that is connected to the VTR termi-
nals on the back of the monitor.
Select VIDEO if you want video and audio from equipment that is con-
nected to inputs 1 and/or 2 on the back of the monitor.
3. If you selected VTR signal input in step 2, the VIDEO 1/VIDEO 2 and AUTO/
MANUAL switches are non-functional.
If you selected VIDEO signal input in step 2, set the AUTO/MANUAL switch to
MANUAL if you are using only one input (input 1 or input 2). Then set the
VIDEO 1/VIDEO 2 switch for the input that you are using.
If you are using inputs 1 and 2, set the AUTO/MANUAL switch to MANUAL if
you want to switch between the inputs manually using the VIDEO 1/VIDEO 2
switch.
If you are using inputs 1 and 2, set the AUTO/MANUAL switch to AUTO if you
want the monitor to switch back and forth automatically between the two in-
puts. If you select AUTO, the VIDEO 1/VIDEO 2 switch is non-functional. You
will set the dwell time for switching between the inputs in step 9.
4. Turn on the power. The LED next to the power switch will light. After about 10
seconds, a picture will appear on the monitor.
5. Adjust the BRIGHTNESS and CONTRAST controls to obtain optimum picture
quality.
6. Adjust the COLOR and TINT controls for desired picture color.
7. Adjust the SHARPNESS control to obtain optimum picture quality.
8. Adjust the VOLUME control for an appropriate audio volume.
9. Adjust the TIME control to obtain the desired dwell time for automatically switch-
ing back and forth between inputs 1 and 2. This function only operates if the
AUTO/MANUAL switch is in the AUTO position.
POWER
AUTO
VIDEO 1
VIDEO 2
VTR
PAL
TINT
COLOR
BRIGHTNESS
CONTRAST
SHARPNESS
TIME
VOLUME
MANUAL
VIDEO
NTSC
Figure 8. Front Panel Controls
Pelco Manual C929M-B (2/97)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
4.0 OPERATION
There are two sources of video and audio input:
•
•
VTR (video tape recorder)
Video 1 and Video 2
Only one source can be selected at a time.
To select the input from a video recorder, set the VTR/VIDEO switch on the front
panel in the VTR position. In this position, the video and audio signals are sent to
the monitor and through the OUTPUT connectors to any equipment connected to
them.
To select the input from Video 1 and/or Video 2:
1. Set the VTR/VIDEO switch on the front panel in the VIDEO position.
2. Set the AUTO/MANUAL switch to MANUAL if you are using only one input
(input 1 or input 2). Then set the VIDEO 1/VIDEO 2 switch for the input that
you are using.
If you are using inputs 1 and 2, set the AUTO/MANUAL switch to MANUAL if
you want to switch between the inputs manually using the VIDEO 1/VIDEO 2
switch.
If you are using inputs 1 and 2, set the AUTO/MANUAL switch to AUTO if you
want the monitor to switch back and forth automatically between the two in-
puts. The VIDEO 1/VIDEO 2 switch is non-functional. Adjust the dwell time for
switching between inputs 1 and 2 with the TIME knob.
When the VTR/VIDEO switch is in the VIDEO position, the video and audio signals
are sent to the monitor and through the OUTPUT connectors to any equipment
connected to them. The signals are also transmitted to the VTR output jacks for
recording.
4.1 PASSIVE LOOPING
If you are using Input 1 and are looping the signal through the IN and OUT connec-
tors (passive looping) (refer to Figures 4 and 5), the monitor does not have to be
turned on unless you want to watch the monitor.
10
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
5.0 MAINTENANCE
To reduce the risk of electric shock, do not remove the cover or back. No user-
serviceable parts are inside. Refer servicing to qualified personnel.
Some household aerosol sprays, cleaning agents, solvents, or polishes may dam-
age the cabinet finish. Clean the cabinet with water and mild soap. Use a soft cloth
for drying.
If the quality of the picture on the monitor is poor and cannot be improved, inspect
all system connections and cable runs.
Pelco Manual C929M-B (2/97)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
6.0 SPECIFICATIONS
ELECTRICAL
Input Power
PMC14E
PMC14EX
120 VAC, 60 Hz
230 VAC, 50 Hz
Power Consumption
PMC14E
PMC14EX
65 W
70 W
System
PMC14E
PMC14EX
NTSC (525 lines, 60 fields per second)
PAL (625 lines, 50 fields per second)
Picture Tube:
14 inches (36 cm) measured diagonally
Effective Picture Size
Height:
8.27 inches (21.0 cm)
11.0 inches (28.0 cm)
Width:
Input Signal:
Composite video, negative synch
-Y: 1.0 Vp-p
-C: 0.286 Vp-p
Subcarrier Frequency
Synch Range at Room
Temperature:
3.579549 MHz +/-200 Hz
4.433619 MHz +/-200 Hz
High Voltage:
23.5KV +/500V
Convergence
At center of
picture:
At corners of
picture:
Less than 1.0 mm
Less than 1.4 mm
Horizontal Resolution
Center:
480 lines
Corners:
380 lines
Brightness:
More than 250 lux in 100% white signal picture at center
12
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL
Dimensions:
13.8" W x 12.4" H x 14.6" D
(35 x 31.5 x 37.1 cm)
Finish:
Steelcabinetpainteddarkgray. Blackbezelaroundthescreen.
Operating
Temperature:
32° to 104° F (0° to 40° C)
Humidity:
0% to 90% (non-condensing)
Connectors
Video Input,
Output:
BNC
Y/C Input,
Output:
Audio Input,
Output:
4-pin mini-Din
RCA
VTR Input,
Output:
RCA
Power Cord:
PMC14E
PMC14EX
3-wire power cord with grounded plug
“Euro” style grounded power cord
Weight
Shipping:
31.74 lbs (14.4 kg)
Pelco Manual C929M-B (2/97)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
7.0 WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
Exceptions to this warranty are as noted below:
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X,
CC3751H-2,CC3651H-2X,MC3651H-2,andMC3651H-2Xcameramodels,whichhaveafive-
year warranty.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed
dome products.
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
Sixmonthsonallpanandtilts,scannersorpresetlensesusedincontinuousmotionapplications
(that is, preset scan, tour and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment.
AllgoodsrequiringwarrantyrepairshallbesentfreightprepaidtoPelco,Clovis,California.Repairs
made necessary by reason of misuse, alteration, normal wear, or accident are not covered under
this warranty.
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the
specific use or application made of the Products. Pelco’s liability for any claim, whether based on
breach of contract, negligence, infringement of any rights of any party or product liability, relating
totheProductsshallnotexceedthepricepaidbytheDealertoPelcoforsuchProducts. Innoevent
will Pelco be liable for any special, incidental or consequential damages (including loss of use, loss
of profit and claims of third parties) however caused, whether by the negligence of Pelco or
otherwise.
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
Ifawarrantyrepairisrequired, theDealermustcontactPelcoat(800) 289-9100or(559)292-1981
to obtain a Repair Authorization number (RA), and provide the following information:
1. Model and serial number
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
If there is a dispute regarding the warranty of a product which does not fall under the warranty
conditions stated above, please include a written explanation with the product when returned.
Methodofreturnshipmentshallbethesameorequaltothemethodbywhichtheitemwasreceived
by Pelco.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800)
289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit,
and RA number if returned for repair).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number
and freight should be prepaid. Ship to the appropriate address below.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed
to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco, the Pelco logo, Camclosure, Esprit,
Genex, Legacy, and Spectra are registered
trademarks of Pelco.
Pelco c/o Expeditors
473 Eccles Avenue
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
Endura and ExSite are trademarks of Pelco.
© Copyright 1997, Pelco. All rights reserved.
14
Pelco Manual C929M-B (2/97)
Download from Www.Somanuals.com. All Manuals Search And Download.
|