®
PMC21A
21-Inch Color Monitor
Installation/
Operation Manual
C1959M (6/99)
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFEGUARDS AND WARNINGS
Observe the following warnings before installing and using this product.
1. Installation and servicing should be done by qualified installation and service person-
nel only.
2. Installation should be done according to all local and national electrical and mechani-
cal codes, using only approved materials.
3. Use only installation methods and materials capable of supporting four times the maxi-
mum specified load.
4. A CCC-approved power cord must be used to power this equipment when used in
China.
Please thoroughly familiarize yourself with the information in this manual prior to installation
and operation.
DESCRIPTION
The PMC21A is a high-resolution color monitor that can be used in desktop applications or
rack mounted using the bezel rack mount that is provided as a standard accessory. The
rack mount is constructed of steel, has a black finish, and occupies 11 rack unit spaces. It is
supplied with eight flat-head screws to attach the rack mount to the monitor, and four 10-32
screws to attach the rack mount to a console.
The monitor supports NTSC and PAL video, as well as 120 VAC and 230 VAC input power.
An automatic switching system makes all the necessary changes for adapting to the re-
quired formats. Manual selection is not required. A separate power cord is supplied for each
voltage input.
The PMC21A features audio input and output, and has a steel housing and front panel con-
trols. The S-VHS high-resolution video (420 horizontal lines at center) and digital comb filter
circuitry add to the superior picture quality.
INSTALLATION
To install the monitor in a rack, start at step 1. Otherwise, start at step 3.
CAUTION: Do
not install this
monitor in a
1. Slide the bezel rack mount onto the monitor from the rear and attach it to the monitor
with the eight M5 flat-head screws provided.
location having excessive
heat or in any way that
obstructs the ventilation
openings in the cabinet.
Premature component
failure or cabinet damage
may result.
2. Place the PMC21A monitor and rack mount into the console, align the mounting holes
of the rack mount with the mounting holes in the console, and insert and tighten the
four 10-32 screws provided. The face of the monitor protrudes approximately 4.8
inches (12.2 cm) from the front of the rack.
FLATHEAD SCREW (8)
BEZEL RACK
MOUNT
NOTE: Installation of the
monitor and rack mount into
the console may require two
persons.
PMC21A MONITOR
Figure 1. Bezel Rack Mount Installation
Pelco Manual C1959M (6/99)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Connect the equipment as shown in Figures 2 through 5. Refer to Table A for the type
of video coaxial cable to use.
Table A. Video Coaxial Cable Requirements
Cable Type*
Maximum Distance
RG59/U
RG6/U
750 ft (229 m)
1,000 ft (305 m)
1,500 ft (457 m)
RG11/U
*Minimum cable requirements:
75 ohms impedance
All-copper center conductor
All-copper braided shield with 95% braid coverage
4. Set the IMPEDANCE switch on the monitor(s) to HIGH if the VIDEO OUT connection
is used. Otherwise, set the switch(es) to the 75-OHM position.
5. Plug the appropriate power cord into the AC INLET connection on the rear panel of the
monitor (refer to Figure 2). Plug the other end into a power receptacle.
AUDIO OUT
JACK (RCA)
CAMERA INPUT
JACK (BNC)
VIDEO OUT
JACK (BNC)
AC
INLET
OUT
CAMERA
INPUT
VIDEO
OUT
S-VHS IN
AUDIO
75Ω
HIGH
IMPEDANCE
IN
IMPEDANCE
SWITCH
(75Ω/HIGH)
S-VHS
JACK
AUDIO IN
JACK (RCA)
Figure 2. Rear Panel Connections
CAMERA
OUT
CAMERA
INPUT
VIDEO
OUT
S-VHS IN
AUDIO
75Ω
HIGH
IMPEDANCE
IN
VCR
Figure 3. One Monitor with External Video Equipment
MAXIMUM OF THREE MONITORS
OUT
OUT
OUT
CAMERA
INPUT
VIDEO
OUT
CAMERA
INPUT
VIDEO
OUT
CAMERA
INPUT
VIDEO
OUT
AUDIO
AUDIO
AUDIO
75Ω
HIGH
75Ω
HIGH
75Ω
HIGH
IMPEDANCE
IMPEDANCE
IMPEDANCE
IN
IN
IN
CAMERA
VCR
Figure 4. Monitor Looping with External Video Equipment
4
Pelco Manual C1959M (6/99)
Download from Www.Somanuals.com. All Manuals Search And Download.
OUT
CAMERA
INPUT
VIDEO
OUT
VCR
S-VHS IN
AUDIO
75Ω
HIGH
IMPEDANCE
IN
Figure 5. S-VHS Video (Y/C) Input Connections
OPERATION
FRONT PANEL CONTROLS
Refer to Figure 6 for front panel controls.
1. Press the POWER switch to turn the monitor on. The power LED lamp above the
switch will illuminate when the power is applied.
2. Press the VIDEO/S-VHS switch to select the S-VHS mode if the S-VHS input jack on
the rear of the monitor is used. Otherwise, select the VIDEO mode. The mode is mo-
mentarily displayed on the upper right portion of the monitor screen at the time it is se-
lected.
3. Adjust the VOLUME control for the desired audio level. Turn the control clockwise to in-
crease and counterclockwise to decrease.
4. Adjust the CONT. control for the desired overall contrast. Proper adjustment will allow
maximum gradations between the darkest and lightest picture contrast. Turn the con-
trol clockwise to increase and counterclockwise to decrease.
5. Adjust the BRIGHT control for the desired overall display brightness. This control is
also useful to compensate for differences in surrounding area lighting. Turn the control
clockwise to increase and counterclockwise to decrease.
6. Adjust the COLOR control to set the color saturation level. Turn the control clockwise
to increase and counterclockwise to decrease.
7. Adjust the SHARP control to obtain the clearest picture.
8. Adjust the TINT control for the proper color phase or flesh tones. When turned clock-
wise, the skin tone becomes greenish. When turned counterclockwise, skin tone be-
comes reddish.
PASSIVE LOOPING
Passive looping is accomplished when two or three monitors are connected in series (see
Figure 4) and a looping signal is sent through the IN and OUT connectors of one monitor
and to the next in series. Unless you want to view the monitor(s), none of them need to be
turned on for passive looping to function.
POWER LED
LAMP
VIDEO/S-VHS
TNT
SHARP COLOR BRIGHT CONT. VOLUME POWER
PMC21A
Figure 6. Front Panel Controls
Pelco Manual C1959M (6/99)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
If the quality of the picture is poor and cannot be improved by making adjustments on the
front control panel, inspect all system connections and cable runs.
To reduce the risk of electrical shock, do not remove the cover or the back. No user-service-
able parts are inside. Refer servicing to qualified personnel or contact the Pelco Customer
Service Department for assistance. Refer to the Warranty and Return Information section.
Clean the cabinet with a cloth slightly dampened with mild household detergent only. Use a
soft cloth for drying. Some household aerosol sprays, cleaning agents, solvents, or polishes
may damage the cabinet finish. Never use strong solvents such as thinner or benzene.
SPECIFICATIONS
ELECTRICAL
Input Voltage:
110-240 VAC, 50/60 Hz
70 watts
Power
Consumption:
Horizontal
Resolution:
420 lines (center)
300 lines (corners)
Picture Tube:
21.0 inches (53.34 cm) measured diagonally
20.5 inches (52.07 cm) measured diagonally
Viewable
Picture Size:
Input Signal:
Composite video, negative sync
Y: 1.0 Vp-p
C: 0.286 Vp-p
Terminals
Video Input Level/
Impedance:
1.0 Vp-p/75 ohms
Video Output Level/
Impedance:
1.0 Vp-p/75 ohms
Audio Input Level/
Impedance:
0.3 Vrms/25K ohms (over)
Audio Output Level/
Impedance:
0.3 Vrms/4.7K ohms (under)
Subcarrier Frequency
Sync Range:
High Voltage:
GENERAL
3.579549 MHz ±200 Hz
4.433619 MHz ±200 Hz at room temperature
25 ±1.2 kV
Connectors
Camera Input/
Video Output:
S-VHS Input:
Audio Input/
Output:
BNC
4-pin mini DIN
RCA
AC Power Cord:
One power cord with grounded plug for 120 VAC
One “Euro”-style grounded power cord for 230 VAC
6
Pelco Manual C1959M (6/99)
Download from Www.Somanuals.com. All Manuals Search And Download.
Construction
Monitor:
Bezel
Steel cabinet
Steel
Rack Mount:
Finish
Monitor:
Bezel
Rack Mount:
Black with black bezel around screen
Black
Dimensions
Monitor:
Bezel
See Figure 7
See Figure 8
52 lb (23.6 kg)
Rack Mount:
Unit Weight:
ENVIRONMENTAL
Operating
Temperature:
Humidity:
32° to 106°F (0° to 41°C)
10% to 95% (non-condensing)
(Design and product specifications subject to change without notice.)
18.9
(48.0)
18.9
(48.0)
17.2
(43.7)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES
Figure 7. PMC21A Dimension Drawing
19.22
(48.82)
18.36
(46.63)
19.00
(48.26)
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES
Figure 8. Bezel Rack Mount Dimension Drawing
Pelco Manual C1959M (6/99)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in material or
workmanship for a period of one year after the date of shipment.
If
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following
information:
1. Model and serial number
Exceptions to this warranty are as noted below:
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Five years on FT/FR8000 Series fiber optic products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
If there is a dispute regarding the warranty of a product which does not fall under the
warranty conditions stated above, please include a written explanation with the product
when returned.
Three years on Camclosure® and fixed camera models, except the CC3701H-2,
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,
which have a five-year warranty.
Method of return shipment shall be the same or equal to the method by which the item was
received by Pelco.
•
•
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series
fixed dome products.
RETURNS
In order to expedite parts returned to the factory for repair or credit, please call the factory at
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned
for credit, and RA number if returned for repair).
•
Two years on Spectra®, Esprit®, ExSite™, and PS20 scanners, including when used in
continuous motion applications.
•
•
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).
All merchandise returned for credit may be subject to a 20% restocking and refurbishing
charge.
Eighteen months on DX Series digital video recorders, NVR300 Series network video
recorders, and Endura™ Series distributed network-based video products.
Goods returned for repair or credit should be clearly identified with the assigned CA or RA
number and freight should be prepaid. Ship to the appropriate address below.
•
•
One year (except video heads) on video cassette recorders (VCRs). Video heads will be
covered for a period of six months.
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:
Six months on all pan and tilts, scanners or preset lenses used in continuous motion
applications (that is, preset scan, tour and auto scan modes).
Service Department
Pelco
3500 Pelco Way
Clovis, CA 93612-5699
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident
are not covered under this warranty.
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are
instructed to return goods to the USA, you may do one of the following:
If the goods are to be sent by a COURIER SERVICE, send the goods to:
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from
the specific use or application made of the Products. Pelco’s liability for any claim, whether
based on breach of contract, negligence, infringement of any rights of any party or product
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for
such Products. In no event will Pelco be liable for any special, incidental or consequential
damages (including loss of use, loss of profit and claims of third parties) however caused,
whether by the negligence of Pelco or otherwise.
Pelco
3500 Pelco Way
Clovis, CA 93612-5699 USA
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:
Pelco c/o Expeditors
473 Eccles Avenue
The above warranty provides the Dealer with specific legal rights. The Dealer may also have
additional rights, which are subject to variation from state to state.
South San Francisco, CA 94080 USA
Phone: 650-737-1700
Fax: 650-737-0933
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive
2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE).
Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual # Date
C1959M 6/99
Comments
Original version.
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.
Endura and ExSite are trademarks of Pelco.
©Copyright 1999, Pelco.
All rights reserved.
8
Pelco Manual C1959M (6/99)
Download from Www.Somanuals.com. All Manuals Search And Download.
|