INS TALLATION/ OP ERATION
500 Series Flat Panel
LCD Monitor
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one blade wider than the
other. A grounding plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the points where they exit from
the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Only use with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-
supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
14. Unplug the apparatus during lightning storms or when unused for long periods of time.
15. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.
16. WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
17. Installation should be done only by qualified personnel and conform to all local codes.
18. Unless this unit is specifically marked as NEMA Type 3, 3R, 3S, 4, 4X, 6, or 6P enclosure, it is designed for indoor use only and it must not
be installed where exposed to rain and moisture.
19. Only use installation methods and materials capable of supporting four times the maximum specified load.
20. Only use replacement parts recommended by Pelco.
21. Avoid touching the screen directly with your fingers as the oils from your skin may be difficult to remove from the LCD.
22. Do not apply direvect pressure on the screen.
23. Keep the monitor in a dust-free environment and away from strong electromagnetic fields.
24. Do not use attachments, such as mounts, that are not recommended by Pelco. They may be hazardous.
25. Do not place the monitor on an unstable stand, bracket, or mount. The unit may fall, causing serious damage to the unit or injury to a
person. Only use mounts recommended by Pelco.
26. A CCC-approved power cord must be used to power this equipment when used in China.
27. A still image displayed too long may cause permanent damage to the LCD panel. Watching the LCD in 4:3 format for a long time may leave
traces of borders displayed on the left, right and center of the screen caused by the difference of light emission on the screen. Using a
camera or a system may cause a similar effect to the screen. Damages caused by this effect are not covered by the warranty.
The product and/or manual may bear the following marks:
This symbol indicates that dangerous voltage constituting a risk of electric shock is
present within this unit.
CAUTION:
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
This symbol indicates that there are important operating and maintenance instructions in
the literature accompanying this unit.
C2937M-C (4/08)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Regulatory Notices
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RADIO AND TELEVISION INTERFERENCE
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Changes and Modifications not expressly approved by the manufacturer or registrant of this equipment can void your authority to operate this
equipment under Federal Communications Commission’s rules.
In order to maintain compliance with FCC regulations shielded cables must be used with this equipment. Operation with non-approved
equipment or unshielded cables is likely to result in interference to radio and television reception.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
4
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
Description
The 500 Series high performance LCD monitors are designed specifically for the security industry and provide high quality display of video or
computer signals using multiple inputs. Adjustments of standard monitor display parameters are made using user-friendly, on-screen menus and
front panel controls.
For viewing multiple cameras simultaneously in high-definition quality on the LCD monitor, Pelco recommends using PMVC4 and PMVR2
multiviewers. The PMVC4 can accept up to four composite inputs while the PMVR2 can accept up to two DVI or VGA inputs. Both models can be
mixed and matched and cascaded together (daisy-chained) to put as many as 60 images of varying window sizes on the screen in clear HD
quality. This method eliminates the need of having multiple CRTs or smaller LCD monitors in racks to monitor security video. One or two LCD
monitors and a number of multiviewers can accomplish the same end with less space, less energy, and more versatility.
MODELS
PMCL523A
23-inch (583 mm) active TFT LCD monitor
26-inch (660 mm) active TFT LCD monitor
32-inch (800 mm) active TFT LCD monitor
37-inch (940 mm) active TFT LCD monitor
42-inch (1,067 mm) active TFT LCD monitor
PMCL526A
PMCL532A
PMCL537A
PMCL542A
EXTERNAL SPEAKERS
External speakers are optional with the 26-, 32-, 37-, and 42-inch models. The external speakers attach to the sides of the monitor. The speaker
model numbers are as follows:
•
•
•
•
PMCL526A-SPKRS for the 26-inch LCD monitor
PMCL532A-SPKRS for the 32-inch LCD monitor
PMCL537A-SPKRS for the 37-inch LCD monitor
PMCL542A-SPKRS for the 42-inch LCD monitor
NOTE: All models have internal speakers. For improved audio performance, external speakers are recommended.
C2937M-C (4/08)
5
Download from Www.Somanuals.com. All Manuals Search And Download.
PACKAGE CONTENTS
Qty Description
1
1
1
1
1
1
2
1
23-, 26-, 32-, 37-, or 42-inch TFT LCD monitor with attached stand (removable)
US standard power cord
EU standard power cord
DVI cable
VGA cable with 15-pin D-sub connection
Remote control unit
AAA batteries
Installation/Operation manual
REMOTE CONTROL
1 EA.
DVI CABLE
1 EA.
USER MANUAL
1 EA.
AAA BATTERIES
2 EA.
MONITOR
VGA CABLE
1 EA.
US POWER CORD
1 EA.
EU POWER CORD
1 EA.
Figure 1. Parts List
6
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
MOUNTING
The monitor can be placed on any flat surface (desk or table), or it can be wall mounted.
•
For the 23-, 26-, and 32-inch models, Pelco recommends the PMCL-WMT tilt wall mount, the PMCL-CM or PMCL-CMP ceiling mount, and
the PMCL-WM1A or PMCL-WM2A articulating wall mounts. The 32-inch model LCD monitor requires an adapter plate (PMCL-V200) to
make these mounts compatible.
•
The 37- and 42-inch models use a PMCP-WM wall mount or the PMCL-CM or PMCL-CMP ceiling mount. The ceiling mount requires a
PMCL-VA adapter plate for the 37- and 42-inch models. Check the Pelco Web site (www.pelco.com) or contact a sales representative for
available mounts as of the publication date of this manual.
Table A. Mounting Hole Patterns
VESA® Compatible
Non-VESA
100 X 100
200 X 200
Universal Mount
PMCL523A
PMCL526A
PMCL532A
PMCL537A
PMCL542A
•
•
•
•
•
DESKTOP STAND
You can remove the desktop stand by removing the four screws that attach the stand to the back of the monitor. Refer to Figure 2.
SCREW
Figure 2. Removing the Stand (PMCL523A Example)
C2937M-C (4/08)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR PANEL CONNECTORS
DVI IN
RGB IN
COMPONENT
Y
V-IN2
V-OUT2
V-IN1
V-OUT1
AC IN
FRONT PC A-OUT A-OUT2
REAR PC A-IN A-IN2
A-OUT1 S-VHS OUT
A-IN1 S-VHS IN
L
R
Pb/Cb Pr/Cr
V-IN2
V-OUT2
V-IN1
V-OUT1
COMPONENT
Y
DVI IN
RGB IN
FRONT PC A-OUT A-OUT2
REAR PC A-IN A-IN2
A-OUT1
A-IN1
S-VHS OUT
S-VHS IN
L
R
AC IN
Pb/Cb Pr/Cr
Figure 3. Rear Panel Connectors
ì
î
ï
DVI IN: Connection to digital video signals from a computer or any DVI output.
RGB IN (VGA): Connection to RGB (VGA) output of a computer or any VGA output.
COMPONENT: Autodetecting component video inputs (Y/LPb/Pr or Y/RCb/Cr) for connecting to the component output jacks of a DVD
player.
PC A-OUT and PC A-IN (loop through): Stereo mini jack input to be used in conjunction with the RGB input from a DVR. Audio loops
through the stereo mini jack output.
ñ
ó
r
A-OUT2, A-IN2, A-OUT1, A-IN1 (loop through): Mono RCA audio inputs.
S-VHS OUT, S-VHS IN (loop through): Connection of S-Video signals from external sources such as VCRs or DVD players. Video loops
through the 4-pin DIN S-Video output.
s
t
u
V-IN2, V-OUT2 (loop through): Input connections from time-lapse VCRs. Video loops through the BNC video output.
V-IN1, V-OUT1 (loop through): Input connections from time-lapse VCRs. Video loops through the BNC video output.
AC IN: Power receptacle, which can be connected to a 100-240 VAC, 50/60 Hz source.
~í (External Speaker Jacks): Stereo mini jack inputs for optional external speakers.
~â (Mounting Holes)
NOTES:
•
•
•
RGB is also referred to as VGA or PC connector in the video security market. We use the term RGB in this manual, in the menu, and on the
remote control. The RGB connector is a D-sub 15-pin female plug. RGB is analog but provides a clear, sharp picture. It can carry either
standard or HDTV formats.
Component is not commonly used in the video security industry. It uses three RCA cables: red, green, and blue for better color separation
and a superior picture over composite. Component is an analog format that can carry standard and high-definition video and is most
commonly found on DVD players. To receive audio, you must connect the DVD output to the audio input.
Digital Video Interface (DVI) provides the best picture. It is used in Pelco products such as Endura®, PMVR2, PMVC4, PL outputs, DVD
players, and satellite boxes. Since the signal received and monitor are both digital, no conversion occurs to degrade the signal. Pelco
recommends using multiviewers (PMVR2, PMVC4) with the 500 Series monitors using DVI. The 500 Series uses a DVI-D interface, so DVI-I
cables will not work. DVI can carry either standard or HDTV formats.
8
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
FRONT PANEL CONTROLS
MENU SOURCE
VOL
MENU
SOURCE
VOL
Figure 4. Front Panel Controls
ì
î
MENU: Displays the main on-screen menu.
SOURCE: Selects the input source and confirms your choice.
ï !and ": Navigates through the on-screen menu.
ñ #VOL$: Increases or decreases the volume. Also selects or adjusts items on the on-screen menu.
ó
r
s
(Power Button): Turns on/off the monitor.
(Remote Control Signal Receiver): Receives remote control signal. Aim the remote control at this spot on the monitor.
(Power Indicator): Indicates power status. Red indicates the power is off; green indicates the power is on.
C2937M-C (4/08)
9
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLING REMOTE CONTROL BATTERIES
Figure 5. Battery Installation
1. Open and remove the battery cover on the back of the remote control.
2. Install two AAA size batteries (supplied). Match the positive (+) and negative (–) signs on the batteries to the signs on the battery
compartment.
3. Close the battery cover. Make sure the lock snaps closed.
WARNINGS:
•
•
•
•
Dispose of batteries in a designated disposal area. Do not throw batteries into a fire.
Do not mix battery types.
Remove dead batteries immediately to prevent battery acid from leaking into the battery compartment.
Remove the batteries if you do not intend to use the remote control for a long period of time.
10
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL FUNCTIONS
ì
î
POWER: Turns on or off power to the monitor.
MUTE: Silences the sound. To return the sound, press MUTE
again, VOL +, or VOL -.
MUTE
POWER
(Input Source): Displays all the available input sources.
Press the button to select the desired input source.
ï
ñ
(PIP): Controls the PIP (picture-in-picture) as follows:
• PIP ON/OFF: Activates/deactivates PIP/PBP mode.
• P.SIZE: Selects the size of the subpicture.
VIDEO1
RGB
VIDEO 2
DVI
S-VIDEO
COMPONENT
P. SWAP
• P.SWAP: Swaps the main and subpicture.
• P.INPUT: Selects an input source for the subpicture.
• P.LOCATION: Selects a location for the subpicture.
• SOUND SEL: Selects the sound of the main or subpicture.
PIP ON/OFF P. SIZE
P. INPUT P. LOCATION SOUND. SEL
(Key Lock): Prevents unauthorized operation of the
equipment by locking the buttons on the front panel. Only the
buttons on the remote control can be used.
NOTE: If the remote control is lost or damaged, pressing and
holding the SOURCE button on the front panel for five seconds
will unlock the keys.
ó
MENU/EXIT
/VOL
KEY LOCK
/VOL +
ENTER
r
s
MENU/EXIT: Displays/exits the on-screen menu.
#/VOL- and $/VOL+, ", !: Controls the cursor in the
on-screen menu, and also adjusts the volume up or down.
SCAN
STILL
ENTER: Confirms (store or enter) your choice in the on-screen
menu.
t
u
~í
STILL: Freezes the current picture.
SCAN: Changes the scan mode of the screen (UNDER, 16:9,
OVER, 4:3).
AUTO COLOR TEMP. 4:3/16:9
BLUE ONLY
~â AUTO: Selects auto adjustment of the screen in RGB mode.
BLUE ONLY: Turns off the red and green colors on the screen
to allow color adjustment using professional calibration tools.
~ä
COLOR TEMP: Adjusts the color temperature (Kelvin) of the
screen Select NORMAL, COOL, or USER.
~ã
4:3/16:9: Swaps the picture between 4:3 mode and 16:9
mode.
~å
Figure 6. Remote Control Functions
C2937M-C (4/08)
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ON-SCREEN DISPLAY (OSD) FUNCTION
INPUT SOURCE DISPLAY
VIDEO 1/2
S-VIDEO
RGB
VIDEO 1
DVI
COMPONENT
Figure 7. Input Source Display Menu
The input source name is displayed in the upper-right corner. You can change the input source there or by pressing one of the input source keys
on the remote control.
MENUS
The menus are the same for the PMCL523A, PMCL526A, PMCL532A, PMCL537A, and PMCL542A. Since different options are available for
different input types, some options may be unavailable.
To use the menus:
1. Press the MENU button to access the Main menu.
2. Use the "and !buttons to highlight a selection.
3. Press the ENTER button to select an item.
4. Use the #/VOL- and $/VOL+ buttons to adjust the setting of a selected item.
12
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
VIDEO 1, VIDEO 2, S-VIDEO COMPONENT MODE MENU
Input Menu
MAIN MENU
VIDEO 1
VIDEO 2
S-VIDEO
RGB
DVI
COMPONENT
INPUT
CONTRAST
BRIGHTNESS
COLOR
SHARPNESS
TINT
Contrast Menu
3D NOISE REDUCTION
LANGUAGE
0
100
PANEL BUTTONS
PIP
SCAN MODE
OSD SETTING
COLOR TEMPERATURE
DEFAULT SETTING
INFORMATION
Brightness Menu
100
0
0
PIP Input Menu
Color Menu
100
VIDEO 1
VIDEO 2
PIP Location Menu
S-VIDEO
COMPONENT
Sharpness Menu
T/L
T/R
B/R
B/L
0
0
15
PIP Size Menu
Tint Menu
LARGE
SMALL
NORMAL
100
PIP Options Menu
PIP OFF
PIP ON
PBP ON
3D Noise Reduction Menu
PIP Swap Menu
SWAP
OFF
NR ON
Setup Menu
Language Menu
PIP OPTION
PIP INPUT
PIP LOCATION
PIP SIZE
ENGLISH
ITALIAN
FRENCH
SPANISH
GERMAN
OSD H Position
0
PIP SWAP
100
OSD V Position
Panel Buttons Menu
0
100
UNLOCK
LOCK
OSD Dwelling Time
OFF
PIP Menu
SETUP
5
30
OSD Setting Menu
OSD H.POSITION
OSD V.POSITION
OSD DISPLAY TIME
Scan Mode Menu
UNDER
16:9
0VER
4:3
R-Gain Menu
B-Gain Menu
0
0
100
100
G-Gain Menu
R-Offset Menu
0
0
0
100
100
OSD Setting Menu
SETUP
User Menu
Color Temp. Menu
R-GAIN
NORMAL
COOL
USER
B-GAIN
B-GAIN
R-OFFSET
G-OFFSET
B-OFFSET
RESET
G-Offset Menu
0
100
R-Offset Menu
100
Default Setting Menu
RESTORE
Reset Setting
RESTORE
INFORMATION
Figure 8. Video 1, Video 2, S-Video, Component Mode Menu
C2937M-C (4/08)
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Video 1, Video 2, S-Video, Component Mode Menu Field Definitions
Input: Select VIDEO 1, VIDEO 2, S-VIDEO, RGB, DVI, or COMPONENT.
Contrast: Adjusts the black level of the video screen image (0 to 100).
Brightness: Adjusts the white level of the video screen image (0 to 100).
Color: Adjusts the color saturation of the video signal (0 to 100).
Sharpness: Adjusts the picture softer or sharper (0 to 15).
Tint: Adjusts the range of color: green to red (0 to 100).
3D Noise Reduction: Reduces the background noise of the video signal (NR ON or OFF).
Language: Select ENGLISH, ITALIAN, FRENCH, SPANISH, or GERMAN for the OSD display.
Panel Buttons: Select UNLOCK or LOCK, and then press Enter to lock/unlock the buttons on the front panel. Authorized users can release the
key lock feature by pressing and holding the SOURCE button for five seconds.
PIP: Select SETUP for the picture-in-picture, and then select one of the following options:
•
•
•
•
•
PIP Option: Select PIP OFF, PIP ON, or PBP ON.
PIP Input: Select VIDEO 1, VIDEO 2, S-VIDEO, or COMPONENT.
PIP Location: Select the PIP position as T/L (top left), T/R (top right), B/R (bottom right), or B/L (bottom left).
PIP Size: Select the PIP size as LARGE, SMALL, or NORMAL.
PIP Swap: Select SWAP to interchange Main with PIP by pressing the ENTER button twice.
Only limited inputs can be selected while in PIP mode, based on the main video source in use (refer to Table B):
Table B. PIP Mode Inputs
Main Video Source Accessible PIP Inputs
Video 1
Video 2
S-Video
RGB
S-Video, Component, Video 2
S-Video, Component, Video 1
Component, Video 1, Video 2
Component, Video 1, Video 2, S-Video
S-Video, Component, Video 1, Video 2
Video 1, Video 2, S-Video
DVI
Component
Scan Mode: Select UNDER, 16:9, OVER, or 4:3 .This is in the Video menu.
OSD Setting: Select SETUP for the on-screen display. Then select one of the following:
•
•
•
OSD H.Position: Adjusts the OSD horizontal position (0 to 100).
OSD V.Position: Adjusts the OSD vertical position (0 to 100).
OSD Display Time: Select OFF or a range of 5-30 seconds.
Color Temperature: Select NORMAL, COOL, or USER. If you select USER, then select from the following calibrations:
•
•
•
•
•
•
•
R-Gain: Adjusts the gain for red (0 to 100).
G-Gain: Adjusts the gain for green (0 to 100).
B-Gain: Adjusts the gain for blue (0 to 100).
R-Offset: Adjusts the offset (or cut) for red (0 to100).
G-Offset: Adjusts the offset (or cut) for green (0 to 100).
B-Offset: Adjusts the offset (or cut) for blue (0 to 100).
Reset: Select RESTORE to return to the original color temperature settings.
Default Setting: Select RESTORE to return to the default settings.
Information: Select INFORMATION to access Pelco headquarters information.
14
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB/DVI MODE MENU
MAIN MENU
INPUT
VIDEO 1
VIDEO 2
S-VIDEO
RGB
CONTRAST
BRIGHTNESS
H. POSITION
V. POSITION
FREQUENCY
DVI
COMPONENT
Contrast Menu
PHASE
AUTO POSITION
LANGUAGE
PANEL BUTTONS
PIP
ASPECT RATIO
OSD SETTING
COLOR TEMPERATURE
DEFAULT SETTING
INFORMATION
0
0
100
Brightness Menu
100
PIP Input Menu
VIDEO 1
H. Position Menu
100
0
VIDEO 2
PIP Location Menu
S-VIDEO
COMPONENT
V. Position Menu
100
T/L
T/R
B/R
B/L
0
0
PIP Size Menu
Frequency Menu
100
LARGE
SMALL
NORMAL
PIP Options Menu
PIP OFF
PIP ON
PBP ON
Phase Menu
PIP Swap Menu
SWAP
0
100
Setup Menu
PIP OPTION
PIP INPUT
PIP LOCATION
PIP SIZE
Auto Position Menu
DISABLE
OSD H Position
0
1024 X 768
1280 X 768
1360 X 768
1366 X 768
PIP SWAP
100
OSD V Position
0
100
Panel Buttons Menu
OSD Dwelling Time
OFF
UNLOCK
LOCK
OSD Setting Menu
5
30
PIP Menu
SETUP
OSD H.POSITION
OSD V.POSITION
OSD DISPLAY TIME
Aspect Ratio
UNDER
16:9
0VER
4:3
R-Gain Menu
B-Gain Menu
0
0
100
100
G-Gain Menu
R-Offset Menu
0
0
100
100
OSD Setting Menu
SETUP
User Menu
Color Temp. Menu
R-GAIN
NORMAL
COOL
USER
B-GAIN
B-GAIN
R-OFFSET
G-OFFSET
B-OFFSET
RESET
G-Offset Menu
0
100
R-Offset Menu
100
Default Setting Menu
RESTORE
0
Reset Setting
RESTORE
INFORMATION
Figure 9. RGB/DVI Mode Menu
C2937M-C (4/08)
15
Download from Www.Somanuals.com. All Manuals Search And Download.
RGB/DVI Mode Menu Field Definitions
NOTE: The DVI menu has a more limited selection. It consists of the following options: Input, Contrast, Brightness, Language, Panel Buttons, PIP,
Aspect Ratio, OSD Setting, Color Temp., Default Setting, and Information.
Input: Select RGB or DVI.
Contrast: Adjusts the black level of the video screen image (0 to 100).
Brightness: Adjusts the white level of the video screen image (0 to 100).
H-Position: (RGB only; not in DVI mode.) Adjusts the horizontal position (0 to 100).
V-Position: (RGB only; not in DVI mode.) Adjusts the vertical position (0 to 100).
Frequency: (RGB only; not in DVI mode.) Adjusts the horizontal size of the screen image (0 to 100).
Phase: (RGB only; not in DVI mode.) Adjusts image distortion appearing as horizontal noise on the screen (0 to 100).
Auto Position: (May be dimmed.) Select DISABLE, 1024 x 768, 1280 x 768, 1360 x 768, or 1366 x 768.
•
•
This menu is an override function.
The menu is enabled only when the input signal is in one of these resolutions. Other resolutions are not displayed, and are set by
autodetection.
•
•
•
If the screen is not displayed correctly, change the resolution selection.
The resolution remains as you set it until changed again.
If the display is distorted or shifted at a resolution of 1366 x 768 or 1360 x 768, adjust the resolution here by manually selecting 1366 x 768
or 1360 x 768.
Language: The choices are English, Italian, French, Spanish, and German.
Panel Buttons: Select UNLOCK or LOCK, and then press Enter to lock/unlock the buttons on the front panel. Authorized users can release the
key lock feature by pressing and holding the SOURCE button for five seconds.
PIP: Select Setup for the picture-in-picture, and then select one of the following:
•
•
•
•
•
PIP Option: Select PIP OFF, PIP ON, or PBP ON.
PIP Input: Select VIDEO 1, VIDEO 2, S-VIDEO, or COMPONENT.
PIP Location: Select the PIP position as T/L (top left), T/R (top right), B/R (bottom right), or B/L (bottom left).
PIP Size: Select the PIP size as LARGE, SMALL, or NORMAL.
PIP Swap: Select SWAP to interchange Main with PIP. (This is in the DVI mode.)
Aspect Ratio: Select UNDER, 16:9, OVER, or 4:3. (This is in DVI mode.)
OSD Setting: Select Setup for the on-screen display. Then select one of the following:
•
•
•
OSD H.Position: Adjusts the OSD horizontal position (0 to 100).
OSD V.Position: Adjusts the OSD vertical position (0 to 100).
OSD Display Time: Select OFF or a range of 5 to 30 seconds.
Color Temperature: Select NORMAL, COOL, or USER. If you select USER, then select from the following calibrations:
•
•
•
•
•
•
•
R-Gain: Adjusts the gain for red (0 to 100).
G-Gain: Adjusts the gain for green (0 to 100).
B-Gain: Adjusts the gain for blue (0 to 100).
R-Offset: Adjusts the offset (or cut) for red (0 to 100).
G-Offset: Adjusts the offset (or cut) for green (0 to 100).
B-Offset: Adjusts the offset (or cut) for blue (0 to 100).
Reset: Select RESTORE to return to the original color temperature settings.
Default Setting: Select RESTORE to return to the default settings.
Information: Select INFORMATION to access Pelco headquarters information.
16
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
Mode Tables
Table C. RGB/DVI Mode
Mode
Resolution
720 x 400
Vertical Frequency (Hz)
70
VGA
640 x 480
50/60/72/75/85
SVGA
800 x 600
56/60/72/75/85
XGA
1024 x 768
1280 x 1024
1360 x 768
1366 x 768
720 x 480
60/70/75/80/85
SXGA
60
60
60
60
50
60
30
WXGA
WXGA
SDTV 480P
SDTV 576P
HDTV 720P
HDTV 1080I
720 x 576
1280 x 720
1920 x 1080
NOTE: The maximum resolution is 1366 x 768 at 60 Hz.
Table D. Main/PIP Mode
MAIN SOURCE
Video1
Video2
S-Video
RGB
DVI
Component
•
•
Video1
Video2
S-Video
•
•
•
•
•
(Swap)*
(Swap)*
•
•
•
•
•
(Swap)*
(Swap)*
•
•
•
(Swap)*
(Swap)*
RGB
DVI
•
•
Component
•
•
•
(Swap)*
(Swap)*
*Swap changes the subpicture to a main picture and vice versa.
C2937M-C (4/08)
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
If the quality of the picture is poor and cannot be improved by making adjustments on the front control panel, inspect all system connections and
cable runs.
WARNING: To reduce the risk of electrical shock, do not remove the cover or back of the monitor. No user-serviceable parts are inside.
Refer servicing to qualified personnel, or contact Pelco Customer Service (1-800-289-9100 or 1-559-292-1981) for assistance. Refer to
Product Warranty and Return Information located on the inside back cover of this document.
CLEANING
•
•
•
•
Gently wipe your screen with a clean camel hair brush or a soft, clean, lint-free cloth.
Gently apply pressure to the screen surface to clean the display.
Do not spray any liquid directly on the screen or the LCD monitor casing.
Chemical cleaners can damage the screen or the LCD monitor casing.
Troubleshooting
Intermittent Loss of Video in PIP/PBP and Main Video
Possible cause: In PAL, when using PIP or PBP, cycling through cameras (with one or more cameras out of operation) causes the monitor to
auto adjust and locate the signal.
Remedy: Check your input devices. If there is a problem with a camera from another input device such as no power signal or bad video, then
correct or disconnect the camera or device.
18
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
Supported Input Modes
Table E. Supported Input Modes
Mode
0
Resolution
720 x 400
640 x 480
640 x 480
640 x 480
640 x 480
640 x 480
800 x 600
800 x 600
800 x 600
800 x 600
800 x 600
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1024 x 768
1280 x 1024
1360 x 768*
1366 x 768*
H Freq. (kHz)
31.469
31.460
31.500
37.700
37.500
43.300
35.100
37.900
48.100
46.900
53.700
48.400
56.500
60.000
64.000
68.300
64.000
47.700
50.000
V Freq. (Hz)
70.000
50.000
60.000
72.000
75.000
85.000
56.000
60.000
72.000
75.000
85.000
60.000
70.000
75.000
80.000
85.000
60.000
60.000
60.000
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
*If the display is distorted or shifted at a resolution of 1366 x 768
or 1360 x 768, you should adjust the resolution in Auto Position on
the OSD menu: MENU>AUTO POSITION OVERRIDE>1366 X 768
or 1360 x 768.
C2937M-C (4/08)
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
MODELS
PMCL523A
PMCL526A
PMCL532A
PMCL537A
PMCL542A
23-inch (583 mm) LCD monitor
26-inch (660 mm) LCD monitor
32-inch (800 mm) LCD monitor
37-inch (940 mm) LCD monitor
42-inch (1,067 mm) LCD monitor
GENERAL
Native Resolution
Optimum Resolution
Panel Aspect Ratio
Viewing Area
1366 x 768 WXGA
1360 x 768/1366 x 768 at 60 Hz depending on graphic card used
16:9
PMCL523A
PMCL526A
PMCL532A
PMCL537A
508 x 286 mm
576 x 324 mm
698 x 392 mm
820 x 461 mm
930 x 523 mm
PMCL542A
Pixel Pitch
PMCL523A
0.372 x 0.372 mm
PMCL526A
0.422 x 0.422 mm
PMCL532A
0.511 x 0.511 mm
PMCL537A
0.600 x 0.600 mm
PMCL542A
0.681 x 0.681 mm
Video Formats
Brightness
PMCL526A
480i, 480p, 576i, 576p, 720p, 1080i
2
450 cd/m
PMCL523A, PMCL532A,
PMCL537A, PMCL542A
Contrast Ratio
PMCL523A
2
500 cd/m
700:1
800:1
PMCL526A
PMCL532A, PMCL537A,
PMCL542A
1000:1
Backlight Type
PMCL523A
6 CCFL
PMCL526A
PMCL532A, PMCL537A
PMCL542A
12 EEFL
16 EEFL
18 EEFL
50,000 hours
Panel Life
Viewing Angle (H/V)
PMCL523A
160°/160°
PMCL526A, PMCL532A,
PMCL537A, PMCL542A
Display Colors
PIP (Picture-In-Picture)
PBP (Picture-By-Picture)
Response Time
PMCL523A,PMCL526A,
PMCL532A
178°/178°
16.7 million
Selectable, sizable, swappable, moveable
Swappable
8 ms
PMCL537A
6 ms
PMCL542A
5 ms
Speakers
2 internal
Front Panel Controls
Indicators
Power, source/enter, menu/exit, up, down, volume minus, volume plus
LED (power on/off)
ELECTRICAL
Input Voltage
Power Consumption
PMCL523A
100-240 VAC, 50/60 Hz
110 W
20
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
PMCL526A
PMCL532A
PMCL537A
PMCL542A
Input Interfaces
Video
120 W
150 W
180 W
220 W
2 BNC, looping; 1 S-Video, looping; 1, RGB; 1 DVI; 1 component
Audio
2, audio L/R, RCA jack; 1 stereo mini jack, looping
Horizontal Frequency
Vertical Frequency
Sync Format
31 kHz to 69 kHz
50 Hz to 85 Hz
NTSC/PAL
PHYSICAL
Dimensions (without stand)
PMCL523A
4.0" D x 23.5" W x 14.8" H
(10.2 x 59.8 x 37.6 cm)
4.2" D x 26.2" W x 18.7" H
(10.7 x 66.6 x 47.5 cm)
4.1" D x 31.7" W x 19.7" H
(10.4 x 80.4 x 50.0 cm)
4.5" D x 36.5" W x 22.2" H
(11.4 x 92.8 x 56.4 cm)
4.7" D x 41.9" W x 25.8" H
(11.9 x 106.3 x 65.5 cm)
PMCL526A
PMCL532A
PMCL537A
PMCL542A
Dimensions (with stand)
PMCL523A
7.1" D x 23.5" W x 17.7" H
(18.0 x 59.8 x 44.9 cm)
8.9" D x 26.2" W x 18.4" H
(22.6 x 66.6 x 46.7 cm)
9.7" D x 31.7" W x 22.1" H
(24.6 x 80.4 x 56.1 cm)
9.7" D x 36.5" W x 24.6" H
(24.6 x 92.8 x 62.5 cm)
9.7" D x 41.9" W x 28.1" H
(24.6 x 106.3 x 71.4 cm)
PMCL526A
PMCL532A
PMCL537A
PMCL542A
Unit Weight (without stand)
PMCL523A
PMCL526A
PMCL532A
PMCL537A
27.6 lb (12.5 kg)
36.4 lb (16.5 kg)
50.7 lb (23.0 kg)
61.7 lb (28.0 kg)
71.6 lb (32.5 kg)
PMCL542A
Unit Weight (with stand)
PMCL523A
PMCL526A
PMCL532A
PMCL537A
30.9 lb (14.0 kg)
43.5 lb (19.7 kg)
58.0 lb (26.3 kg)
71.6 lb (32.5 kg)
81.5 lb (40.0 kg)
PMCL542A
Shipping Weight
PMCL523A
PMCL526A
PMCL532A
PMCL537A
35.0 lb (15.9 kg)
46.0 lb (20.9 kg)
62.0 lb (28.1 kg)
78.0 lb (35.4 kg)
84.0 lb (38.1 kg)
PMCL542A
ENVIRONMENTAL
Operating Temperature
Storage Temperature
Operating Humidity
Storage Humidity
32° to 104°F (0° to 40°C)
-4° to 140°F (-20° to 60°C)
20% to 80%, noncondensing
10% to 90%, noncondensing
C2937M-C (4/08)
21
Download from Www.Somanuals.com. All Manuals Search And Download.
OPTIONAL ACCESSORIES
Mounts
PMCL-CM
Ceiling mount for PMCL523A, PMCL526A, PMCL532A
PMCL-CMP
PMCL-WM1A
PMCL-WM2A
PMCP-WM
PMCL-WMT
PMCL-VA
Ceiling mount for PMCL523A, PMCL526A, PMCL532A
Articulating wall mount for PMCL523A, PMCL526A, PMCL532A
Articulating wall mount for PMCL523A, PMCL526A, PMCL532A
Fixed wall mount for PMCL537A and PMCL542A
Tilt wall mount for PMCL523A, PMCL526A, PMCL532A
Adapter plate required for use with ceiling mounts for PMCL537A and PMCL542A
Converts 200 x 200 mm to 100 x 100 mm VESA pattern. (Required for use with the PMCL532A and Pelco
monitor mounts with 200 x 200 mm VESA pattern.)
PMCL-V200
Speakers
PMCL526A-SPKRS
PMCL532A-SPKRS
PMCL537A-SPKRS
PMCL542A-SPKRS
Optional external speakers for PMCL526A
Optional external speakers for PMCL532A
Optional external speakers for PMCL537A
Optional external speakers for PMCL542A
Multiviewers
PMVR2
PMVC4
Multiviewer with 2 DVI and 2 VGA inputs, VGA or DVI output
Multiviewer with 4 composite inputs, VGA or DVI output
NOTE: Check the Pelco Web site at www.pelco.com or contact a sales representative for available newer mounts as of the publication date of
this manual.
(Design and product specifications subject to change without notice.)
22
C2937M-C (4/08)
Download from Www.Somanuals.com. All Manuals Search And Download.
PRODUCT WARRANTY AND RETURN INFORMATION
WARRANTY
Pelco will repair or replace, without charge, any merchandise proved defective in
material or workmanship for a period of one year after the date of shipment.
Pelco assumes no risk and shall be subject to no liability for damages or loss
resulting from the specific use or application made of the Products. Pelco’s liability
for any claim, whether based on breach of contract, negligence, infringement of
any rights of any party or product liability, relating to the Products shall not exceed
the price paid by the Dealer to Pelco for such Products. In no event will Pelco be
liable for any special, incidental, or consequential damages (including loss of use,
loss of profit, and claims of third parties) however caused, whether by the
negligence of Pelco or otherwise.
Exceptions to this warranty are as noted below:
•
Five years on fiber optic products and TW3000 Series unshielded twisted pair
(UTP) transmission products.
•
•
•
Three years on Spectra® IV products.
Three years on Genex® Series products (multiplexers, server, and keyboard).
The above warranty provides the Dealer with specific legal rights. The Dealer may
also have additional rights, which are subject to variation from state to state.
Three years on DX Series digital video recorders, DVR5100 Series digital video
®
recorders, DigitalSENTRY Series hardware products, DVX Series digital video
recorders, NVR300 Series network video recorders, and Endura® Series
distributed network-based video products.
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the
following information:
•
Three years on Camclosure® and Pelco-branded fixed camera models, except
the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and
MC3651H-2X camera models, which have a five-year warranty.
1. Model and serial number
2. Date of shipment, P.O. number, sales order number, or Pelco invoice number
3. Details of the defect or problem
•
•
•
Three years on PMCL200/300/400 Series LCD monitors.
Two years on standard motorized or fixed focal length lenses.
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8
Series fixed dome products.
Two years on Spectra III™, Spectra Mini, Esprit®, ExSite®, and PS20 scanners,
including when used in continuous motion applications.
If there is a dispute regarding the warranty of a product that does not fall under
the warranty conditions stated above, please include a written explanation with
the product when returned.
•
•
•
Method of return shipment shall be the same or equal to the method by which the
item was received by Pelco.
Two years on Esprit and WW5700 Series window wiper (excluding wiper
blades).
Two years (except lamp and color wheel) on Digital Light Processing (DLP®)
displays. The lamp and color wheel will be covered for a period of 90 days. The
air filter is not covered under warranty.
RETURNS
To expedite parts returned for repair or credit, please call Pelco at (800) 289-9100
or (559) 292-1981 to obtain an authorization number (CA number if returned for
credit, and RA number if returned for repair) and designated return location.
•
•
Two years on Intelli-M® eIDC controllers.
One year (except video heads) on video cassette recorders (VCRs). Video heads
will be covered for a period of six months.
All merchandise returned for credit may be subject to a 20 percent restocking and
refurbishing charge.
•
Six months on all pan and tilts, scanners, or preset lenses used in continuous
motion applications (preset scan, tour, and auto scan modes).
Pelco will warrant all replacement parts and repairs for 90 days from the date of
Pelco shipment. All goods requiring warranty repair shall be sent freight prepaid
to a Pelco designated location. Repairs made necessary by reason of misuse,
alteration, normal wear, or accident are not covered under this warranty.
Goods returned for repair or credit should be clearly identified with the assigned
CA or RA number and freight should be prepaid.
1-8-08
The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive 2002/96/EC of the European Union
regarding the disposal of waste electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling this equipment.
REVISION HISTORY
Manual #
C2937M
C2937M-A
C2937M-B
C2937M-C
Date
1/07
5/07
12/07
4/08
Comments
Original version.
Added PMCL-V100 per ECO 07-17659.
Revised the document due to change of manufacturer. All models are new.
Included 1360 x 768 resolution in the Auto Position description and the Supported Input Modes chart. Added Optimum Resolution to the specifications. Added a
Mounting Hole Patterns table. Updated the warranty.
Pelco, the Pelco logo, Camclosure, Digital Sentry, Endura, Esprit, ExSite, Genex, Intelli-M, Legacy, and Spectra are registered trademarks of Pelco, Inc.
Spectra III is a trademark of Pelco, Inc.
© Copyright 2008, Pelco, Inc. All rights reserved.
DLP is a registered trademark of Texas Instruments Incorporated.
Download from Www.Somanuals.com. All Manuals Search And Download.
Worldwide Headquarters
3500 Pelco Way
Clovis, California 93612 USA
USA & Canada
Tel: 800/289-9100
Fax: 800/289-9150
International
Tel: 1-559/292-1981
Fax: 1-559/348-1120
ISO9001
Australia Finland France Germany Italy Macau The Netherlands Russia Singapore
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.
|