Pelco Car Video System C1665M A 1 06 User Manual

I N S T A L L A T I O N  
TW3004P  
Passive Four-Channel  
Video Transceiver  
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Description  
The TW3004P is a four-channel passive video transceiver that can transmit multiple video signals over  
unshielded twisted pair (UTP) cable. The transceiver can be mounted into a fiber rack (RK5000PS-3U/  
RK5000-3U). Each transceiver has four rubber feet for placement on a flat surface, such as a desk or  
shelf.  
The transceiver can be used at the camera and/or monitoring location. It allows for easy connectivity  
with any video source or destination device, such as cameras, monitors, and matrix switchers. This  
multichannel transceiver will transmit video (color/black-white) and Coaxitron® (up-the-coax) PTZ  
control signals on the same pair of UTP wires.  
Although the transceiver is passive and requires no power, the Pelco badge on the front of the unit illu-  
minates when inserted into a fiber rack. The transceiver has built-in surge suppression.  
PARTS OF THE TRANSCEIVER  
4
2
3
1
Figure 1. TW3004P Parts  
Pelco Badge  
BNC Connector (4)  
4-Pin Power Connector  
8-Pin Terminal Block Connector  
Rubber Feet (4)  
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Installation  
Make sure all parts are present for the unit.  
1
1
Terminal block (with tension clamps)  
Wall clip  
MOUNTING  
The TW3004P transceiver is three rack units high and can be mounted into a fiber rack or onto a wall  
using a fiber wall mount kit or the supplied wall clip.  
USING A RACK  
You can mount a TW3004P into either an RK5000PS-3U or an RK5000-3U. For additional information,  
refer to the RK5000PS-3U/RK5000-3U Fiber Rack Mount Chassis Installation manual.  
USING WALL MOUNT KITS  
The optional WM5001-3U wall mount base kit allows attachment of a single TW3004P to a wall.  
Up to two WM5001-3UEXP wall mount expansion kits can be used to allow attachment of two  
additional transceivers to the wall. For additional information, refer to the Fiber Wall Mount Kits  
Installation manual.  
USING A WALL CLIP  
To attach the TW3004P transceiver to a wall using the supplied wall clip, refer to Figure 2 and do the  
following:  
1. Attach the wall clip to a wall using two screws (not supplied).  
2. Slide the transceiver into the clip until the two holes on the bottom of the transceiver align with  
the two holes on the lower flange of the clip.  
3. Attach the transceiver to the clip using the two Phillips pan head screws provided with the clip.  
4
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
UPPER  
FLANGE  
VERTICAL  
MOUNTING HOLE (2)  
HORIZONTAL  
MOUNTING HOLE (2)  
TW3004P  
LOWER  
FLANGE  
SCREW, PHILLIPS  
PAN HEAD WITH  
LOCK WASHER (2)  
WALL CLIP  
Figure 2. Mounting the TW3004P Using the Wall Clip  
APPLICATIONS  
Figures 4 through 7 show how to use the transceivers in various applications. For example, the  
TW3004P can be connected to a Spectra® or a Camclosure®. The terminal block on the back of the  
TW3004P has tension clamps instead of screw terminals.  
To connect the UTP wires to the terminal block:  
1. Use a small screwdriver to open the clamps (+ and -) for each channel.  
2. Insert each wire into the appropriate holes. Figure 3 shows the UTP wires for channel 1.  
4
3
2
1
Figure 3. Terminal Block UTP Connections  
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
   
Table A shows the distance in feet with Coaxitron or video only when using a particular type of  
Cat cable. Table B shows the maximum allowable wire gauge for single wire and stranded wire.  
Table A. Cable Distance  
Distance  
(with Coaxitron)  
Distance  
(video only)  
Cable Type  
Cat3  
Cat5  
Cat5e  
Cat6  
300 ft  
500 ft  
750 ft  
750 ft  
400 ft  
650 ft  
750 ft  
750 ft  
NOTE: Cat5e cable is recommended for optimum video performance.  
Table B. Wire Gauge  
Wire Gauge (maximum allowable)  
24 AWG (1.5 mm2)  
24 AWG (1.0 mm2)  
Single Wire (solid)  
Stranded Wire (flexible)  
TW3004P  
TW3004P  
POWER CONNECTOR  
FOR PELCO BADGE  
UTP  
4
2
4
2
3
1
3
1
MONITOR  
FIXED CAMERA  
Figure 4. Connecting Two Transceivers  
6
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
10 PINS (5-/6+)  
TW3004P  
PIN 5 +  
PIN 4 -  
POWER CONNECTOR  
FOR PELCO BADGE  
FIXED CAMERA  
8 PINS (4-/5+)  
UTP  
4
2
3
1
MONITOR  
Figure 5. Connecting a UTP Camera to a UTP Receiver  
NOTE: UTP cameras have a 10-pin RJ-45 connector. Standard RJ-45 connectors have 8 pins. Refer to  
Figure 5 for correct pin outs.  
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
 
TW3004P  
VC-UTP BOARD  
POWER CONNECTOR  
FOR PELCO BADGE  
SPECTRA  
COAXITRON  
UTP  
4
2
3
1
MONITOR  
VIDEO  
MATRIX  
Figure 6. Coaxitron PTZ Control  
8
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TW3004P  
BLUE WIRE =  
GRAY WIRE =  
POWER CONNECTOR  
FOR PELCO BADGE  
CAMCLOSURE  
UTP  
4
2
3
1
MONITOR  
Figure 7. UTP Camclosure to UTP Receiver  
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Specifications  
ELECTRICAL  
Power Source  
Wire Type  
Wire Category  
12 VDC (for Pelco badge only)  
Unshielded twisted pair (24 AWG maximum)  
Cat3 or better  
Wire Impedance  
Wire Distance  
100 ohms 20%  
750 feet maximum  
DC Loop Resistance  
Differential Capacitance  
Transient Immunity  
Insertion Loss  
52 ohms per 1,000 feet  
19pF/ft max  
300 W peak pulse power (8/20 US)  
<1 dB; 0-8 MHz frequency range  
VIDEO CHARACTERISTICS  
Video Input/Output  
Format  
1, BNC; internally terminated in 75 ohms  
NTSC, PAL, SECAM  
Frequency Response  
DC to 10 MHz  
Common Mode/Differential  
Mode Rejection  
>60 dB typical  
MECHANICAL  
Connectors  
BNC  
Video input/output  
8-Pin Terminal Block  
4-Pin Connector  
UTP input/output  
Rack power for Pelco badge  
Construction  
Finish  
Steel  
Silver  
GENERAL  
Operating Temperature  
Relative Humidity  
Data Transmission  
Dimensions  
-40° to 185°F (-40° to 85°C)  
0 to 90%, noncondensing  
Supports Coaxitron up to 750 feet  
8.75" D x 1.08" W x 4.81" H  
(22.23 x 2.74 x 12.22 cm)  
Unit Weight  
1.46 lb (0.66 kg)  
This equipment contains electrical or electronic components that must be recycled properly to  
comply with Directive 2002/96/EC of the European Union regarding the disposal of waste  
electrical and electronic equipment (WEEE). Contact your local dealer for procedures for recycling  
this equipment.  
10  
C1665M-A (1/06)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of  
shipment.  
Exceptions to this warranty are as noted below:  
Five years on FR/FT/FS Series fiber optic products and TW3000 Series unshielded twisted pair transmission products.  
Three years on Spectra® IV products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
Three years on Camclosure® and fixed camera models, except the CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and  
MC3651H-2X camera models, which have a five-year warranty.  
Three years on PMCL200/300/400 Series LCD monitors.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series fixed dome products.  
Two years on Spectra III, Esprit®, ExSite, and PS20 scanners, including when used in continuous motion applications.  
Two years on Esprit and WW5700 Series window wiper (excluding wiper blades).  
Two years (except lamp and color wheel) on Digital Light Processing (DLP®) displays. The lamp and color wheel will be covered for a period of  
90 days. The air filter is not covered under warranty.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video recorders, and EnduraSeries distributed network-based video  
products.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be covered for a period of six months.  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion applications (that is, preset scan, tour and auto scan modes).  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco shipment. All goods requiring warranty repair shall be sent freight  
prepaid to Pelco, Clovis, California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident are not covered under this  
warranty.  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from the specific use or application made of the Products. Pelcos  
liability for any claim, whether based on breach of contract, negligence, infringement of any rights of any party or product liability, relating to the Products  
shall not exceed the price paid by the Dealer to Pelco for such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused, whether by the negligence of Pelco or otherwise.  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have additional rights, which are subject to variation from state  
to state.  
If a warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or (559) 292-1981 to obtain a Repair Authorization number (RA), and  
provide the following information:  
1. Model and serial number  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
If there is a dispute regarding the warranty of a product which does not fall under the warranty conditions stated above, please include a written  
explanation with the product when returned.  
Method of return shipment shall be the same or equal to the method by which the item was received by Pelco.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization  
number (CA number if returned for credit, and RA number if returned for repair).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing charge.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA number and freight should be prepaid. Ship to the appropriate  
address below.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are instructed to return goods to the USA, you may do one of the  
following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco  
Pelco c/o Expeditors  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
473 Eccles Avenue  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
REVISION HISTORY  
Manual #  
C1665M  
C1665M-A  
Date Comments  
12/05 Original version.  
1/06 Revised Table A.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, Coaxitron, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 2007, Pelco.  
All rights reserved.  
DLP is a registered trademark of Texas Instruments, Inc.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Worldwide Headquarters  
3500 Pelco Way  
Clovis, California 93612 USA  
USA & Canada  
Tel: 800/289-9100  
Fax: 800/289-9150  
International  
Tel: 1-559/292-1981  
Fax: 1-559/348-1120  
ISO9001  
Australia Canada Finland France Germany Italy Macau The Netherlands Russia Singapore  
|
|
|
|
|
|
|
|
|
South Africa Spain Sweden United Arab Emirates United Kingdom United States  
|
|
|
|
|
Download from Www.Somanuals.com. All Manuals Search And Download.  

Pelco Security Camera C1988M B User Manual
Philips Clock Radio SJ T113632006 User Manual
Philips Computer Monitor 105S5 User Manual
Philips Computer Monitor 107E40 User Manual
Philips Cordless Telephone DECT5212S User Manual
Philips VCR VR1010BP User Manual
Pioneer Home Theater System SD 532HD5 User Manual
Pioneer Portable Speaker S 7EX User Manual
Pioneer Welder CDJ 2000nexus User Manual
PYLE Audio Car Stereo System PLDTF5M User Manual