Pelco Car Satellite TV System c19596 99 User Manual

®
PMC21A  
21-Inch Color Monitor  
Installation/  
Operation Manual  
C1959M (6/99)  
Pelco • 3500 Pelco Way • Clovis, CA 93612-5699 USA • www.pelco.com  
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150  
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120  
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFEGUARDS AND WARNINGS  
Observe the following warnings before installing and using this product.  
1. Installation and servicing should be done by qualified installation and service person-  
nel only.  
2. Installation should be done according to all local and national electrical and mechani-  
cal codes, using only approved materials.  
3. Use only installation methods and materials capable of supporting four times the maxi-  
mum specified load.  
4. A CCC-approved power cord must be used to power this equipment when used in  
China.  
Please thoroughly familiarize yourself with the information in this manual prior to installation  
and operation.  
DESCRIPTION  
The PMC21A is a high-resolution color monitor that can be used in desktop applications or  
rack mounted using the bezel rack mount that is provided as a standard accessory. The  
rack mount is constructed of steel, has a black finish, and occupies 11 rack unit spaces. It is  
supplied with eight flat-head screws to attach the rack mount to the monitor, and four 10-32  
screws to attach the rack mount to a console.  
The monitor supports NTSC and PAL video, as well as 120 VAC and 230 VAC input power.  
An automatic switching system makes all the necessary changes for adapting to the re-  
quired formats. Manual selection is not required. A separate power cord is supplied for each  
voltage input.  
The PMC21A features audio input and output, and has a steel housing and front panel con-  
trols. The S-VHS high-resolution video (420 horizontal lines at center) and digital comb filter  
circuitry add to the superior picture quality.  
INSTALLATION  
To install the monitor in a rack, start at step 1. Otherwise, start at step 3.  
CAUTION: Do  
not install this  
monitor in a  
1. Slide the bezel rack mount onto the monitor from the rear and attach it to the monitor  
with the eight M5 flat-head screws provided.  
location having excessive  
heat or in any way that  
obstructs the ventilation  
openings in the cabinet.  
Premature component  
failure or cabinet damage  
may result.  
2. Place the PMC21A monitor and rack mount into the console, align the mounting holes  
of the rack mount with the mounting holes in the console, and insert and tighten the  
four 10-32 screws provided. The face of the monitor protrudes approximately 4.8  
inches (12.2 cm) from the front of the rack.  
FLATHEAD SCREW (8)  
BEZEL RACK  
MOUNT  
NOTE: Installation of the  
monitor and rack mount into  
the console may require two  
persons.  
PMC21A MONITOR  
Figure 1. Bezel Rack Mount Installation  
Pelco Manual C1959M (6/99)  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
3. Connect the equipment as shown in Figures 2 through 5. Refer to Table A for the type  
of video coaxial cable to use.  
Table A. Video Coaxial Cable Requirements  
Cable Type*  
Maximum Distance  
RG59/U  
RG6/U  
750 ft (229 m)  
1,000 ft (305 m)  
1,500 ft (457 m)  
RG11/U  
*Minimum cable requirements:  
75 ohms impedance  
All-copper center conductor  
All-copper braided shield with 95% braid coverage  
4. Set the IMPEDANCE switch on the monitor(s) to HIGH if the VIDEO OUT connection  
is used. Otherwise, set the switch(es) to the 75-OHM position.  
5. Plug the appropriate power cord into the AC INLET connection on the rear panel of the  
monitor (refer to Figure 2). Plug the other end into a power receptacle.  
AUDIO OUT  
JACK (RCA)  
CAMERA INPUT  
JACK (BNC)  
VIDEO OUT  
JACK (BNC)  
AC  
INLET  
OUT  
CAMERA  
INPUT  
VIDEO  
OUT  
S-VHS IN  
AUDIO  
75  
HIGH  
IMPEDANCE  
IN  
IMPEDANCE  
SWITCH  
(75/HIGH)  
S-VHS  
JACK  
AUDIO IN  
JACK (RCA)  
Figure 2. Rear Panel Connections  
CAMERA  
OUT  
CAMERA  
INPUT  
VIDEO  
OUT  
S-VHS IN  
AUDIO  
75  
HIGH  
IMPEDANCE  
IN  
VCR  
Figure 3. One Monitor with External Video Equipment  
MAXIMUM OF THREE MONITORS  
OUT  
OUT  
OUT  
CAMERA  
INPUT  
VIDEO  
OUT  
CAMERA  
INPUT  
VIDEO  
OUT  
CAMERA  
INPUT  
VIDEO  
OUT  
AUDIO  
AUDIO  
AUDIO  
75  
HIGH  
75Ω  
HIGH  
75Ω  
HIGH  
IMPEDANCE  
IMPEDANCE  
IMPEDANCE  
IN  
IN  
IN  
CAMERA  
VCR  
Figure 4. Monitor Looping with External Video Equipment  
4
Pelco Manual C1959M (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OUT  
CAMERA  
INPUT  
VIDEO  
OUT  
VCR  
S-VHS IN  
AUDIO  
75  
HIGH  
IMPEDANCE  
IN  
Figure 5. S-VHS Video (Y/C) Input Connections  
OPERATION  
FRONT PANEL CONTROLS  
Refer to Figure 6 for front panel controls.  
1. Press the POWER switch to turn the monitor on. The power LED lamp above the  
switch will illuminate when the power is applied.  
2. Press the VIDEO/S-VHS switch to select the S-VHS mode if the S-VHS input jack on  
the rear of the monitor is used. Otherwise, select the VIDEO mode. The mode is mo-  
mentarily displayed on the upper right portion of the monitor screen at the time it is se-  
lected.  
3. Adjust the VOLUME control for the desired audio level. Turn the control clockwise to in-  
crease and counterclockwise to decrease.  
4. Adjust the CONT. control for the desired overall contrast. Proper adjustment will allow  
maximum gradations between the darkest and lightest picture contrast. Turn the con-  
trol clockwise to increase and counterclockwise to decrease.  
5. Adjust the BRIGHT control for the desired overall display brightness. This control is  
also useful to compensate for differences in surrounding area lighting. Turn the control  
clockwise to increase and counterclockwise to decrease.  
6. Adjust the COLOR control to set the color saturation level. Turn the control clockwise  
to increase and counterclockwise to decrease.  
7. Adjust the SHARP control to obtain the clearest picture.  
8. Adjust the TINT control for the proper color phase or flesh tones. When turned clock-  
wise, the skin tone becomes greenish. When turned counterclockwise, skin tone be-  
comes reddish.  
PASSIVE LOOPING  
Passive looping is accomplished when two or three monitors are connected in series (see  
Figure 4) and a looping signal is sent through the IN and OUT connectors of one monitor  
and to the next in series. Unless you want to view the monitor(s), none of them need to be  
turned on for passive looping to function.  
POWER LED  
LAMP  
VIDEO/S-VHS  
TNT  
SHARP COLOR BRIGHT CONT. VOLUME POWER  
PMC21A  
Figure 6. Front Panel Controls  
Pelco Manual C1959M (6/99)  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE  
If the quality of the picture is poor and cannot be improved by making adjustments on the  
front control panel, inspect all system connections and cable runs.  
To reduce the risk of electrical shock, do not remove the cover or the back. No user-service-  
able parts are inside. Refer servicing to qualified personnel or contact the Pelco Customer  
Service Department for assistance. Refer to the Warranty and Return Information section.  
Clean the cabinet with a cloth slightly dampened with mild household detergent only. Use a  
soft cloth for drying. Some household aerosol sprays, cleaning agents, solvents, or polishes  
may damage the cabinet finish. Never use strong solvents such as thinner or benzene.  
SPECIFICATIONS  
ELECTRICAL  
Input Voltage:  
110-240 VAC, 50/60 Hz  
70 watts  
Power  
Consumption:  
Horizontal  
Resolution:  
420 lines (center)  
300 lines (corners)  
Picture Tube:  
21.0 inches (53.34 cm) measured diagonally  
20.5 inches (52.07 cm) measured diagonally  
Viewable  
Picture Size:  
Input Signal:  
Composite video, negative sync  
Y: 1.0 Vp-p  
C: 0.286 Vp-p  
Terminals  
Video Input Level/  
Impedance:  
1.0 Vp-p/75 ohms  
Video Output Level/  
Impedance:  
1.0 Vp-p/75 ohms  
Audio Input Level/  
Impedance:  
0.3 Vrms/25K ohms (over)  
Audio Output Level/  
Impedance:  
0.3 Vrms/4.7K ohms (under)  
Subcarrier Frequency  
Sync Range:  
High Voltage:  
GENERAL  
3.579549 MHz ±200 Hz  
4.433619 MHz ±200 Hz at room temperature  
25 ±1.2 kV  
Connectors  
Camera Input/  
Video Output:  
S-VHS Input:  
Audio Input/  
Output:  
BNC  
4-pin mini DIN  
RCA  
AC Power Cord:  
One power cord with grounded plug for 120 VAC  
One “Euro”-style grounded power cord for 230 VAC  
6
Pelco Manual C1959M (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Construction  
Monitor:  
Bezel  
Steel cabinet  
Steel  
Rack Mount:  
Finish  
Monitor:  
Bezel  
Rack Mount:  
Black with black bezel around screen  
Black  
Dimensions  
Monitor:  
Bezel  
See Figure 7  
See Figure 8  
52 lb (23.6 kg)  
Rack Mount:  
Unit Weight:  
ENVIRONMENTAL  
Operating  
Temperature:  
Humidity:  
32° to 106°F (0° to 41°C)  
10% to 95% (non-condensing)  
(Design and product specifications subject to change without notice.)  
18.9  
(48.0)  
18.9  
(48.0)  
17.2  
(43.7)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES  
Figure 7. PMC21A Dimension Drawing  
19.22  
(48.82)  
18.36  
(46.63)  
19.00  
(48.26)  
NOTE: VALUES IN PARENTHESES ARE CENTIMETERS; ALL OTHERS ARE INCHES  
Figure 8. Bezel Rack Mount Dimension Drawing  
Pelco Manual C1959M (6/99)  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
PRODUCT WARRANTY AND RETURN INFORMATION  
WARRANTY  
Pelco will repair or replace, without charge, any merchandise proved defective in material or  
workmanship for a period of one year after the date of shipment.  
If  
a
warranty repair is required, the Dealer must contact Pelco at (800) 289-9100 or  
(559) 292-1981 to obtain a Repair Authorization number (RA), and provide the following  
information:  
1. Model and serial number  
Exceptions to this warranty are as noted below:  
2. Date of shipment, P.O. number, Sales Order number, or Pelco invoice number  
3. Details of the defect or problem  
Five years on FT/FR8000 Series fiber optic products.  
Three years on Genex® Series products (multiplexers, server, and keyboard).  
If there is a dispute regarding the warranty of a product which does not fall under the  
warranty conditions stated above, please include a written explanation with the product  
when returned.  
Three years on Camclosure® and fixed camera models, except the CC3701H-2,  
CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X camera models,  
which have a five-year warranty.  
Method of return shipment shall be the same or equal to the method by which the item was  
received by Pelco.  
Two years on standard motorized or fixed focal length lenses.  
Two years on Legacy®, CM6700/CM6800/CM9700 Series matrix, and DF5/DF8 Series  
fixed dome products.  
RETURNS  
In order to expedite parts returned to the factory for repair or credit, please call the factory at  
(800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned  
for credit, and RA number if returned for repair).  
Two years on Spectra®, Esprit®, ExSite, and PS20 scanners, including when used in  
continuous motion applications.  
Two years on Esprit® and WW5700 Series window wiper (excluding wiper blades).  
All merchandise returned for credit may be subject to a 20% restocking and refurbishing  
charge.  
Eighteen months on DX Series digital video recorders, NVR300 Series network video  
recorders, and EnduraSeries distributed network-based video products.  
Goods returned for repair or credit should be clearly identified with the assigned CA or RA  
number and freight should be prepaid. Ship to the appropriate address below.  
One year (except video heads) on video cassette recorders (VCRs). Video heads will be  
covered for a period of six months.  
If you are located within the continental U.S., Alaska, Hawaii or Puerto Rico, send goods to:  
Six months on all pan and tilts, scanners or preset lenses used in continuous motion  
applications (that is, preset scan, tour and auto scan modes).  
Service Department  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699  
Pelco will warrant all replacement parts and repairs for 90 days from the date of Pelco  
shipment. All goods requiring warranty repair shall be sent freight prepaid to Pelco, Clovis,  
California. Repairs made necessary by reason of misuse, alteration, normal wear, or accident  
are not covered under this warranty.  
If you are located outside the continental U.S., Alaska, Hawaii or Puerto Rico and are  
instructed to return goods to the USA, you may do one of the following:  
If the goods are to be sent by a COURIER SERVICE, send the goods to:  
Pelco assumes no risk and shall be subject to no liability for damages or loss resulting from  
the specific use or application made of the Products. Pelcos liability for any claim, whether  
based on breach of contract, negligence, infringement of any rights of any party or product  
liability, relating to the Products shall not exceed the price paid by the Dealer to Pelco for  
such Products. In no event will Pelco be liable for any special, incidental or consequential  
damages (including loss of use, loss of profit and claims of third parties) however caused,  
whether by the negligence of Pelco or otherwise.  
Pelco  
3500 Pelco Way  
Clovis, CA 93612-5699 USA  
If the goods are to be sent by a FREIGHT FORWARDER, send the goods to:  
Pelco c/o Expeditors  
473 Eccles Avenue  
The above warranty provides the Dealer with specific legal rights. The Dealer may also have  
additional rights, which are subject to variation from state to state.  
South San Francisco, CA 94080 USA  
Phone: 650-737-1700  
Fax: 650-737-0933  
This equipment contains electrical or electronic components that must be recycled properly to comply with Directive  
2002/96/EC of the European Union regarding the disposal of waste electrical and electronic equipment (WEEE).  
Contact your local dealer for procedures for recycling this equipment.  
REVISION HISTORY  
Manual # Date  
C1959M 6/99  
Comments  
Original version.  
Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered trademarks of Pelco.  
Endura and ExSite are trademarks of Pelco.  
©Copyright 1999, Pelco.  
All rights reserved.  
8
Pelco Manual C1959M (6/99)  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Peavey Musical Instrument Amplifier 115 TXR User Manual
Perle Systems TV Converter Box C 10GT SFP User Manual
Philips Cell Phone CTS660BLK 00 User Manual
Philips Hair Clippers 25LC User Manual
Philips Handheld TV RD 0525C User Manual
Pioneer Car Video System AVH P6600DVD User Manual
Pioneer DVD Player BDP 51FD User Manual
Pioneer DVD Player BDP 121 User Manual
Pioneer Stereo Receiver VSX 518 User Manual
ProForm Treadmill PFTL99602 User Manual